|
| 1 | Earth work in excavation by mechanical means(Hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 mtr in width as well as 10 sqm on plan) in all kinds of soil including rock and disposal of surplus, excavated earth at dumping sites to be purchased by the contractor and approved by the engineer-in-charge at site for safe disposal of same without damaging private /public property and all required leads/lifts and carriage.(Complete job) in 80 AKS 10 OR 10 H?R |
| 2 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level in 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate) 40mm nominal size crushed. |
| 3 | Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:1.5:3 |
| 4 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1.5:3 |
| 5 | Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement. in 1:1.5:3 |
| 6 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level in 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). With 20 perecent boulders |
| 7 | Brick work with common burnt clay (non modular) bricks of class designation 7.5 in cement mortar 1:6 (1 cement : 6 fine sand). |
| 8 | Extra for brick masonary above plinth level |
| 9 | Half brick masonry with bricks of class designation 75 in foundation, plinth and superstructure upto floor V-level in cement mortar 1:4 (1 cement : 4 coarse sand). |
| 10 | Reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete TMT bars. |
| 11 | 6 mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand) |
| 12 | 12mm cement plaster of mix 1:6 (1 cement : 6 fine sand). |
| 13 | Providing and laying in position cement concrete of specified grade including the cost of shuttering all work upto Plinth level in 1:4:8 stone aggregate) 40mm nominal size crushed stone aggregate including curing |
| 14 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering, lead upto 50Mt & lift upto 1.50M. |
| 15 | Hand Packed stone filling including supply of stones |
| 16 | Foundations, footings, bases of columns. |
| 17 | Columns, pillars, piers. |
| 18 | Lintels, beams, |
| 19 | Suspended floors, roofs, landings and access platforms. |
| 20 | Wall (any thickness) including attached pilasters, buttresses, plinth and string courses fillets etc |
| 21 | Stair Case |
| 22 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. |
| 23 | Providing edge moulding to 18 mm/16 mm thick marble stone counters, Vanities stairs etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge for granite work |
| 24 | Providing and fixing ceramic glazed floor tiles (non-skidding) 300x300mm (thickness to be specified by the manufactures) of Premium quality conforming to IS : 13755 of ORIENT, SOMANY, KAJARIA or equivalent make in colour such as white, Ivory, Grey, Fume Red, Brown laid on 20mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc. complete. |
| 25 | Providing and fixing Ist quality ceramic glazed wall tiles 300X600mm conforming to IS : 13753 of minimum thickness 5mm of approved make like SOMANY, KAJARIA or equivalent make in all colour, shades except burgundy, bottle green, black of any size as approved by Engineer in charge over 12mm thick bed of cement mortar 1:3 (1cement : 3coarse sand) and jointing with grey cement slurry @ 3.3Kg per sqm including pointing in white cement mixed with pigment of matching shade complete. |
| 26 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete |
| 27 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): |
| 28 | Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size |
| 29 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.With ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws |
| 30 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws |
| 31 | Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge :second class deodar wood. |
| 32 | 150x10mm. |
| 33 | 200x10mm. |
| 34 | 125mm. |
| 35 | 100mm. |
| 36 | Providing and fixing hanging floor door stopper ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete. Twin rubber stopper. |
| 37 | P/F stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc, including welded, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered including fixing accessories such as nuts, bolts, fasteners etc. |
| 38 | Providing and fixing M.S grills of required pattern in frames of windows etc. with M.S flats, square or round bars etc. including priming coat with approve steel primer all complete (fixed to openings/wooden frames with rawl plugs, screws etc.). |
| 39 | Steel work welded in built-up sections/framed work including cutting hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required in gratings, frames, guard bar, ladders, railings, brackets, gates and similar work. |
| 40 | Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacture,over the plasterted wall surface to prepare the surface even and smooth complete |
| 41 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer |
| 42 | Finishing wall with acrylic smooth exterior paint of required shade on New work (two or more coats applied @ 1.67 litre/10 sqm over and including base coat of water proofing cement paint applied @ 2.20kg/10sqm) |
| 43 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content.on steel/wood work |
| 44 | Sand for an average lead of 120 kms |
| 45 | Stone aggregate fo r an average lead of 20 Kms. |
| 46 | Bricks for an average lead of 150 Kms |
| 47 | Stone fo r an average lead of 5 Kms. |
| 48 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) (Essel Cat No-76031011 / Kerovit Cat No- KS112 / CERA CAT NO- S1053121) with seat and lid, 10 liter low level white P.V.C. flushing cistern (Essel Cat No- 402101 / Kervoit Cat No- KO1005 / CERA CAT NO- B1010110), including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:18.2.1 W.C. pan with ISI marked white solid plastic seat and lid. (MAKE:- Kerovit, Essel, CERA, Hindware) |
| 49 | Providing and fixing wash basin (Essel Cat No-72001140 / Kerovit Cat No- KS234 / CERA CAT NO- S2040120) with C.I. brackets, 15 mm dia CP Brass single hole basin mixer (Essel Cat No-113001 / Kerovit Cat No- KB1311010 / CERA CAT NO- F1020451) of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer. (MAKE:- Kerovit, Essel, CERA, Hindware) |
| 50 | Providing and fixing white vitreous china pedestal (Essel Cat No-72011071 / Kerovit Cat No- 305 / CERA CAT NO- S2090113) for wash basin completely recessed at the back for the reception of pipes and fittings. (MAKE:- Kerovit, Essel, CERA, Hindware) |
| 51 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 18.11.1 Kitchen sink with drain board 18.11.1.1 510x1040mm bowl depth 250mm (MAKE:- Kerovit, Essel, CERA, Hindware) |
| 52 | Providing and fixing concealed body for single lever diverter 35mm (ESSEL CAT NO- 180104, KEROVIT CAT NO- KB2011035 & CERA CAT NO- F1020711) cartridge with button assembly , cartridge sleeve (button on top ) but without exposed parts. Complete job . (MAKE:- Kerovit, Essel, CERA, Hindware) |
| 53 | Providing and fixing Ornamix prime bathtub spout (ESSEL CAT NO- 310015, KEROVIT CAT NO- KB2111016 & CERA CAT NO- F1020661) with wall flange. Complete job . (MAKE:- Kerovit, Essel, CERA, Hindware) |
| 54 | Providing and fixing single lever exposed parts kit of diverter (ESSEL CAT NO- 113003, KEROVIT CAT NO- KB2111037 & CERA CAT NO- F4020101) consisting of operating lever , wall flange, with seal & button only . Complete job (MAKE:- Kerovit, Essel, CERA, Hindware) |
| 55 | Providing and fixing of wall mounted over head shower 200mm SQUARE (ESSEL CAT NO- 304106, KEROVIT CAT NO- KA570030 & CERA CAT NO- F7010116SS) with shower arm round shape with 90 degree bend with flanges with all fittings. (MAKE:- Kerovit, Essel, CERA, Hindware) |
| 56 | Providing and fixing CP Brass Single lever telephonic wall mixer (Essel Cat No 113067-307001 / Kerovit Cat No.KB411020-KA510002 & CERA CAT NO- F1020403-F7030101AB) of quality & make as approved by Engineer in charge. (a) 15 mm nominal dia. (MAKE:- Kerovit, Essel, CERA, Hindware) |
| 57 | Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS : 8931. (MAKE:- Kerovit, Essel, CERA, Hindware) |
| 58 | Providing and fixing 15 mm nominal bore C.P. brass angle valve (Essel Cat No 113052, Kerovit Cat No- KB2111003 & CERA CAT NO- F1023201) for basin mixer and geyser points or wherever required as per the direction of Engineer Incharge of approved make conforming to IS : 8931. (MAKE:- Kerovit, Essel, CERA, Hindware) |
| 59 | Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-incharge.(MAKE:- Kerovit, Essel, CERA, Hindware) |
| 60 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to European type W.C. of quality and make as approved by Engineer - in - charge. (MAKE:- Kerovit, Essel, CERA Hindware) |
| 61 | Providing & fixing C.P. hand spray with lever control (health faucet) (ESSEL CAT NO- 309004, Kerovit CAT NO- KA580007 & CERA CAT NO- F8030106AB) and flexible hose 1 m long connection with C.P. holder for hand spray complete in all respects as per direction of Engineer-Incharge. (MAKE:- Kerovit, Essel, CERA, Hindware) |
| 62 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C waste fittings complete: 18.28.1 Semi rigid pipe 18.28.1.1 32 mm dia (MAKE:- Kerovit, Essel, CERA, Hindware) |
| 63 | Providing and fixing P.V.C. waste pipe for sink or wash basin (ESSEL CAT NO- 301206) including P.V.C waste fittings complete: 18.28.2 Flexible pipe 18.28.2.1 40 mm dia (MAKE:- Kerovit, Essel, CERA, Hindware) |
| 64 | Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour: 18.69.1 Waste coupling 31mm of 79 mm length and 62 mm breadth weighing not less than 45gms. (MAKE:- Kerovit, Essel, CERA, Hindware) |
| 65 | Providing and fixing PTMT Bottle Trap for Wash basin and sink: 18.70.1 Bottle trap 31 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms. (MAKE:- Kerovit, Essel, CERA, Hindware) |
| 66 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with brackets of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. (MAKE:- Kerovit, Essel, CERA, Hindware) |
| 67 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with a minimum distance of 37 mm from wall face with concealed fittings arrangements of approved quality and colour, weighing not less than 88 gms. (MAKE:- Kerovit, Essel, CERA, Hindware) |
| 68 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour: 18.73.1 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms. (MAKE:- Kerovit, Essel, CERA, Hindware) |
| 69 | Providing and fixing PTMT shelf 440 mm long, 124 mm width and 36 mm height of approved quality and colour, weighing not less than 300 gms. (MAKE:- Kerovit, Essel, CERA, Hindware) |
| 70 | Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan.or wherever required as per the direction of Engineer Incharge. (MAKE:- Kerovit, Essel, CERA, Hindware) |
| 71 | Providing and fixing PTMT soap dish holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106gms. (MAKE:- Kerovit, Essel, CERA, Hindware) |
| 72 | Cooling capacity 20 Ltrs./hr (Model No. Bluestar PC240) Storage capacity 40 Ltrs. |
| 73 | Providing & fixing commercial 20 LPH water purifier of required capacity 8 LTR. Including all components as per manufacture specifications, including connection from water supply line, and final connection to water cooler electric wiring & plug top etc. with all accessories.(MAKE:- KENT GRAND, AQUAGUARD, OR EQUIVALENT) |
| 74 | Capacity 10 liters |
| 75 | Capacity 25 liters |
| 76 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. (MAKE:- Kerovit, Essel, CERA, Hindware) |
| 77 | 1216 (16mm OD) pipe. |
| 78 | 1620 (20mm OD) pipe. |
| 79 | 1216 (16mm OD) pipe. |
| 80 | 1620 (20mm OD) pipe. |
| 81 | 2025 (25mm OD) pipe. |
| 82 | 25 mm dia. nominal bore (Medium) |
| 83 | 32 mm dia. nominal bore (Medium) |
| 84 | 40 mm dia. nominal bore (Medium) |
| 85 | 25 mm dia. nominal bore (Medium) |
| 86 | 32 mm dia. nominal bore (Medium) |
| 87 | 40 mm dia. nominal bore (Medium) |
| 88 | 15 mm nominal bore |
| 89 | 20 mm nominal bore |
| 90 | 25 mm nominal bore |
| 91 | 32 mm dia. nominal bore |
| 92 | 40 mm dia. nominal bore |
| 93 | 25 mm dia. nominal bore (Medium) |
| 94 | 32 mm dia. nominal bore (Medium) |
| 95 | 40mm dia. nominal bore (Medium) |
| 96 | 25 to 40 mm nominal bore |
| 97 | 15 mm dia. nominal bore |
| 98 | 20 mm dia. nominal bore |
| 99 | 25 mm dia. nominal bore |
| 100 | 32 mm dia. nominal bore |
| 101 | 40mm dia. nominal bore |
| 102 | Earthwork in all kinds of soil excavation by manual means in trenches for foundations, drains, pipes, cable etc. (not exceeding 1.5 in width) and for shafts, wells, cesspits and the like not exceeding 10 Sqm on plan, depth upto 1.5 Mtr including disposal of excavated earth upto 1 Mtr from cutting edge, disposed earth is to be levelled and neatly dressed. |
| 103 | 75MM dia |
| 104 | Constructing brick masonry chamber for underground C.I. inspection chamber and bend with common burnt clay (non modular) bricks of class designation 7.5 in cement mortar 1:4 ( 1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg ) R.C.C. top slab with 1:1 ½ : 3 mix ( 1 cement : 1 ½ coarse sand : 3 graded stone aggregate 20 mm nominal size),foundation concrete 1:5:10 (1 cement: 5 fine sand: 10 graded stone aggregate 40mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design Inside dimensions 455x610 mm and 45 cm deep for single pipe line- |
| 105 | Constructing brick masonry chamber for underground C.I. inspection chamber and bend with common burnt clay (non modular) bricks of class designation 7.5 in cement mortar 1:4 ( 1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg ) R.C.C. top slab with 1:1 ½ : 3 mix ( 1 cement : 1 ½ coarse sand : 3 graded stone aggregate 20 mm nominal size),foundation concrete 1:5:10 (1 cement: 5 fine sand: 10 graded stone aggregate 40mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard designInside dimensions 600x850 mm and 45 cm deep for single pipe line with three or more inlets. |
| 106 | Providing and fixing Heavy class SS grating with Cockroach proof SS strainer of approved design including setting in floor with cement motor to match with floor finish as per direction of Engineer-Incharge. (Size 100 mm dia) (ISI Marked) |
| 107 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank (Sintex, Electroplast, star, Lotous or equivalent having valid ISI license) (1000 ltr. Capacity.). |
| 108 | Making soak pit 2.5m diameter 3.0 M deep with 45x45cm dry brick honey comb shaft with bricks of class designation 75mm and S.W. drain pipe 100mm diameter 1.8 m long complete as per standard design with FPS bricks. Please Enable Macros to View BoQ information |
