|
| 1 | M&L for repairing of spalled concrete from ceiling in the following stages:-a. Preparation of existing surfaces like chipping of unsound weak / loose concrete with electric hammer or manually including tapering all edges, making square shoulders of cavities etc. n.exc 50 mm thickness removal of debries, complete all as specified and directed. b. Applying rust remover cum passivator Sika rust off 100 or equivalent @ 0.20kg/Sqm/per coat or as per manufacturer\"s specifications to remove rust from existing reinforcement c.Applying a epoxy based zinc rich rebar corrosion protection system of product : Fiazin (R) R @ 0.15Kg/Sqm/coat or as per manufacturer\"s specifications d. Mixing & applying two component Epoxy resin concrete Bonding coat of Sikadur(R)-32 LP A & B @ 0.40 Kg/Sqm(Mixing proportion as per manufacturer\"s instructions) on prepared RCC surfaces as per manufacture specification including preparation of surface by chipping and thoroughly cleaning of surface complete whereverrequired over new reinforcement (if required) complete all as specified and directed. (Reinforcement will be measured and paid separately).e. Apply a pre-batched one component polymer modified cementious patch repair mortar n.exc 50mm in layer of 15mm thick each of Product: Sika Mono Top®-122 Fas per manufacturer instructions complete all as specified and directed. f. Apply aluminized synthetic resin Concrete curing compounds for the prevention of premature water loss from concrete of product: Antisol®-E(WP)@ 0.10 to 0.20 kg/m2 as manufacturers instructions complete all as specified and directed. |
| 2 | M & L for providing rebar of required length & dia with Sika Anchor Fix ® -3/Mungo/Fischer FISV 390/HiltiRE-500 epoxy resin wherever required in RCC members including power drilling for holes (of size 16mmx160mm ), cleaning of holes, filled with epoxy to ensure the bond as per manufacturers instructions, complete all as specified and directed. |
| 3 | Making \"V\" groove of 5mm wide and 5mm deep over crack line by electrically operated angle grinder with diamond concrete saw blade and cleaning it by air blower and sealing it with polymer modified mortar complete all as specified and directed. |
| 4 | Drilling and fixing NRV injection packers in RC members including, (a)Drilling Holes: Drilling holes in structural members at the intervals as per recommendation of engineer in charge.(b)Cleaning of holes: Clean the holes by air blower prior to fixing nozzles. Fixing of Packers: Insert 12 mm dia., 50~75 mm long injection packers in cleaned holes with solvent free, moisture insensitive epoxy resin based putty or equivalent.(c)Cutting of Packers: Cut the packers by cut of wheel after completionof grouting without damaging structural elements. |
| 5 | M & L for shrinkage free low viscous epoxy resin based injection grout.Product: Sikadur®-52 as per manufacturers instructions and complete all as specified and directed. |
| 6 | M & L for mixing & applying two component Epoxy resin concrete Bonding coat of Sikadur(R)-32 LP A & B @ 0.40 Kg/Sqm(Mixing proportion as per manufacturer\"s instructions) on prepared RCC surfaces as per manufacture specification including preparation of surface by chipping and thoroughly cleaning of surface complete whereverrequired over new reinforcement (if required) andcomplete all as specified and directed. (Reinforcement will be measured and paid separately). |
| 7 | M & L for water tight centering and shuttering including bolting, strutting, propping etc. including removal of form work from column, beam etc. complete all as specified and directed. |
| 8 | M & L for ready to use non shrink, cementitious free flow micro-concrete (> 100 mm). Product: Seared® Microcrete-4 + adequate coarse aggregate, Yield: approx. 17 later/bag (30kg) (depending on the size and quantity of coarse aggregate added) Product requirements: compressive strength > 60 N/mm2 (28 days) according to ASTM C 1107-99, complete all as specified and directed. |
| 9 | M & L for aluminised synthetic resin Concrete curing compounds for the prevention of premature water loss from concrete of productAntisol®-E(WP) (Product Requirement: Antisol®-E(WP) conforms to ASTM C 309-89 Type II Class A) @ 0.10 to 0.20 kg/m2, complete all as specified and directed. |
| 10 | M & L for protection plaster (25 – 30 mm) reinforced with virgin polypropylene mono filament fibers with admixture: Sika® plastocrete Plus @ 0.10 kg per bag of cement, reinforcement: Sika® Fiber h 150 @ 0.9 kg/cum complete all as specified and directed. (Product requirements admixture: conforms to IS 2645. Product requirements reinforcement: conforms to ISO 9001-2000 and ASTM C 1116 type III4.1.3; specific gravity: 0.91 kg/ltr; fine monofilament; alkali proof; containing no reprocessed olefin materials). |
| 11 | M&L for PCC tiles of size 250x250x22mm thick fixed & jointed in grey cement with pigments in cement mortar over & including 10mm thick cement screed bed in CM (1:4) complete all as specified and directed. |
| 12 | Dismantling of brick tiles or terracing tiles single layer on roof complete all as specified and directed. |
| 13 | Demolition of mud phuska on roof slabs, any thickness including cleaning of roof surfaces and removing the debris upto the distance exc. 1.00Km but n. exc. 1.5Km complete all as specified and directed. |
| 14 | Scraping of old tar felt roof treatment over concrete padding of any thickness etc from roof including finishes or junction or parapet and cleaning the surface (by mechanical means like grinder, etc) complete all as specified and directed. |
| 15 | M&L for cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) on roof padding with water proofing compound surface finished even and smooth without using extra cement complete all as specified and directed. (Rate of WPC shall be included in unit rate) |
| 16 | M&L for water proofing treatment in following stages:-1.Rendering in CM 1:3 with waterproofing liquid as per manufacturer\"s instruction over concrete surface finished even and smooth without using extra cement.2.First coat of bitumen primer confirming to IS-3384@ 0.40 Kg/Sqm over plastered surface.(Bitumen primer shall be TANK MASTIC of M/S STP Ltd or ‘EMW FLATE’ of M/S Texas India Ltd).3. Second coat of binding material using blown type bitumen confirming to IS-702 Gde 85/25 @ 1.2 Kg/Sqm applied over bitumen primer.4. Third layer of APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 Kg/Sqm with a centre core of 90 micron high density polyethylene film protected on both sides with a high quality polymeric asphaltic mix, the polymeric asphaltic mix will be protected on both sides with thermo fusable HMHDPE filmof make super thermolay manufactured by STP Ltd or ‘Hyper Plas’ (Polyster) manufacturedby M/S IWL Ltd or ‘Shaliplas’ (polyester) manufactured by M/S Capital Steels and chemicals Pvt Ltd as approved by GE, black finish reinforced with non-woven polyester matt, with a thermo fusable finish. Torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at the sides and 100mm at the ends complete all as specified and as directed. 5.Final coat of binding material using blown type bitumen confirming to IS-702 Gde 85/25 @ 1.2 Kg/Sqm applied over APP membrane. Over this layer stone dust @ 0.50 Kg/Sqm shall be applied uniformly. |
| 17 | Water proofing treatment of sunken RCC slab : (i) Demolition of unreinforced cement concrete exc 15cm thickness for sunken portion of WC, and removal of the same from premises complete all as specified and directed. (ii) Apply a coat of cement sullry @ 0.488 kg/sqm mixed with tapecrete @ 0.253 kg/sqm after surface preparation all as per manufacturer\"s instructions.(iii) Apply hot bitumen 30/40 (grade S-35) conforming to IS-73-1961 @ 0.70 kg/sqm and providing transparent polythene film 200micron (heavy duty) conforming to IS - 2508-1977 laid with 150mm overlaps.(iv) Then apply 1.5mm thick layer of cement slurry @ 1.288 kg/sqm mixed with tapecrete @ 0.570 kg/sqm and course sand @ 1.298 kg/sqm.Allow the treatment to air curing for 4 hours followed by water curing for 48 hrs.The whole treatment shall be taken upto full depth of parapet wall and tuck into groove in parapet around, and fluhing the edges of treatment into floor finishes.(v)Sunken floor shall be filled with graded cinder (including PCC 1:5:10 Type-C2 using 40mm graded stone aggregate). |
| 18 | S&F in repair 100mm dia CI spun soil, waste and vent pipes in any length, with or without ears, with cement joints, fixed to walls including dismantling of old unsv pipes, complete all as specified and directed. |
| 19 | S&F in repair 75mm CI spun soil, waste and vent pipe in any length with or without ears with cement joints fixed to walls, including dismantling of old unsv pipes complete all as specified and directed. |
| 20 | S&F in repairs 100mm bore spun cast iron bends/Tee (any radius) diminishing pieces or tapers (larger bore to be measured) with oval access doors complete all as specified and directed. |
| 21 | All as per item No.20 here-in-beforeabove but 75mm bore of pipe. |
| 22 | S&F CI Cowl for 100mm bore of CI spun pipe. |
| 23 | Suplply only 75mm dia CI floor trap with grating including jointing to waste pipe with lead joint,fixed complete all as specified & directed. |
| 24 | Taking down chowkats or frames not exc. 1.5 sq. m with shutters (without taking off shutters from the frames) , complete all as specified and directed. |
| 25 | Taking down chowkats or frames exc. 1.5 sq. m but not exc 4 sqm each with shutters (without taking off shutters from the frames) , complete all as specified and directed. |
| 26 | Taking down shutters of any description exc 1 sq. m and not exc 2 sqm each, and refixing in the same opening complete all as specified and directed. |
| 27 | Taking down old window / ventilators with frame, any description, including guard bars not exc 1.5 sqm each , complete all as specified and directed. |
| 28 | S&F powder coated anodised aluminium frame for windows, ventilators, grill with one or more rebates including necessary joining cleat, powder coated aluminium snap beading, screws for fixing etc. complete all as specified and directed.Note: (1) Only aluminium items to be measured.(2) Glass, wire mesh, handles to be measured & paid separately.(3) Minimum thickness of powder coating to be 50 micron. |
| 29 | S & F powder coated anodised aluminium window and ventilator shutters, side hung type with out sash bars, aluminium sections weighing not less than 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150 mm long ( 1 No.) hinges type B-21 100 mm long (2no.) suitable handle 1 no.) each shutter complete all as specified and directed. |
| 30 | S&F powder coated (minimum thickness of powder coating 50 micron) aluminium sliding three track window, three shutter Series B(SHUTTER SECTION-18mm) withtwo glazed shutters each covering half opening and one gauged shutter covering one third openingincluding self closing locking arrangement, stoppers and rubber beading gasketwithout sash bar aluminum section weighing 1.06 Kg/RM including necessary jointing cleats glazing clips rubber packing powder coated aluminum beading screws including fittings in each shutter with 5 mm thick tinted glass & also including stainless steel wire cloth of 0.36 mm dia and avg width of aperture 1.40 mmcomplete all as specified and directed.Note:- Three way track sliding window of frame size 92x31.75x1.5 mm and shutter size 40x18mm with 9mm interlocking leg x 1.45mm thick and weight not less than 0.607kg/RM. |
| 31 | S & F for mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors, angle iron chowkhats; ladders; framed balusters; walk ways; railings; framework of water tanksand similar work conforming to Fe.290.Gde-E-165, complete all as specified and directed. |
| 32 | S&F 35 mm thick 2nd class hardwood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, cla-use 8.24 (a); supplied and fitted to chowkats incl one shop coat of pink primer complete all as specified and directed. |
| 33 | S & F factory made 35 mm thick 2nd class hardwood Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated including one shop coat of pink primer complete all as specified and directed. |
| 34 | S&F 19mm thick Medium density fiber board, exterior grade, fixed to timber framework with screws on both sides as shutter of cupboard complete all as specified and directed. |
| 35 | S&F Solid PVC moulded door frame of size 50mm x 95mm made out of5mm wood grain printed PVC sheet reinforced with M.S square tube, complete all as specified and directed. |
| 36 | S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30 mm thick (stiles),with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain MouldedPVC Sheet Polyurethane painted on the front face & 2mm Plain colour PVC Sheet on back face complete all as specified and directed. |
| 37 | S & F stainless steel butt hinges 100mm long medium weight etc complete all as specified and directed. |
| 38 | S & F200mm long aluminum, anodized barrel tower bolts of extruded section complete all as specified and directed. |
| 39 | S & Faluminum anodised handle 150 mm long cast type complete all as specified and directed. |
| 40 | S&F in repair stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples (for windows and gauzed doors) complete all as specified and directed. |
| 41 | S&F for Factory made FRP Chhajjas of suitable sizes2.0mm thick of any colour and shade in roof covering/chajjas covering, cladding to wall fixed with all necessary nutt and bolts fixed in and including 150x150x150mm bed in walls including cutting of chase in wall and inserting 50 mm deep, and making good and matching the surface with existing finish, complete all as specified and directed. |
| 42 | M & L for preparation of new or previously untreatedwood or wood based surface of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint (approved tint) over a coat of pink primer complete all as specified and directed. |
| 43 | S&F in repair110 mm bore DWC pipes single socket in any lengthwith rubber ring/ cement solvent cement joints fixed to walls including MS clamps of suitable size made of flat iron 25x3mm including taking down old unsv pipes complete all as specified and directed. |
| 44 | S&F in repair 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches, floors including necessary bends, Tees or cowl fixed to walls or floors including taking down of old pipe of any description complete all as specified and as directed. |
| 45 | S&F in repair 40 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches, floors including necessary bends, Tees or cowl fixed to walls or floors including taking down of old pipe of any description complete all as specified and as directed. |
| 46 | Demolition of reinforced cement concrete roofs, floors (other than ground floor), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed. |
| 47 | M&L for ready mix concrete (RMC) of design mix M-25 (using 20mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs landings, balconies canopies, deck slabs and in shelves and complete all as specified and directed. |
| 48 | S&F TMTbars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed. |
| 49 | S&F TMTbars 6mmto 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed. |
| 50 | All as per Srl itemNo. 49.00 above but TMT bars 6mm and over upto and including 8mm as in stirrups, spacers and binders., complete all as specified and directed. |
| 51 | M&Lform work to soffits of suspended slab such as roof beams/slabs, chhajja, floor slabs, cover slab, shelves, landing and similar work not exc. 200mm thickness finished rough (horizontal or sloping) complete all as specified and directed. |
| 52 | M&Lform work to sides and soffits of floor or roof beams, beams,haunchings, griders bressummers lintels, cantilevers shelves including sup-ports, overhangs, etc also splays between floors and beams etc, complete all as specified and directed. |
| 53 | M&L formwork to edges of concrete flats, treads, breaks in floors, windows cills, concrete railings, opening in concrete walls, floor and roofs n.exc 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n.exc 20cm wide rough finished surfaces complete all as specified and directed. |
| 54 | M&L for 15mm thick rendering of ready mix mortar of approved make on brick work or concrete surfaces on wall, finish the surface even and smooth without using extra cement as whole or in patch etc complete all as specified and directed.Note :Cost for necessary steel formwork & shutteringof the above aspects shall be deemed to be included in the quoted rate of the respective item and nothing extra shall be paid on any account. |
| 55 | M&L 5mm thick rendering of ready mix mortar of approved make (having ratio equivalent to CM 1:3)of ceiling surface finished fair even and smooth without using extra cement as whole or in patch complete all as specified and directed. |
| 56 | M&L for Keyed pointing to brick walls in cement mortar (1:4) and matching with existing keyed pointing including raking out joints, complete all as specified and directed. |
| 57 | M&L for complete removal of existing treatment on walls with electric sander machine and steel wire brushes to the entire satisfaction of Engr-in-Charge including rendering on external wall surfaces in CM (1:4) including water proofing compound upto four storey buildings complete all as specified and directed.Note :(cost of necessary scaffolding and safety measure are inclusive in unit quoted rates). |
| 58 | M&L for preparing new or old plastered surfaces on walls and applying two coat of cement base paint over a coat of alkali resistant primer complete all as specified and directed. |
| 59 | M&L for complete removal of existing treatmentby brooming down or steel wire brushing, scrapping down smoke, mass, efflorescent salt and oil and greasy spot etc. washing rubbing down distemper surfaces and applying Birla white putty 2mm on wall even and smooth surface and applying two coat of oil bound distemper over a coat of primer (of approved quality and tint) on wall using painting roller, complete all as specified and directed. |
| 60 | M&L for preparation of old decorated surfaces and applying two coats of white wash on ceiling complete all as specified and directed. |
| 61 | M&L for preparation of new plastered surfaces and applying three coats of white wash on ceiling complete all as specified and directed. |
| 62 | Demolition of cement concrete Infloors and paving in any position and any thickness (below or above ground level all as specified and directed. |
| 63 | M&L for Plinth protection 75 mm thick in PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) laid in alternate bays(not exc 2 Sqm each) finished even and fair at top using extra cement and providing joints throughout the thickness of plinth protection, filled with mastic filling comprising one part of bitumen 85/25 graded and three parts of sand by weight complete all as specified and directed. |
| 64 | M & L for preparation of old painted wood or wood based surface of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint (approved tint) complete as specified and directed. |
| 65 | Material and labour for preparation of old steel surface of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint (approved tint) complete as specified and directed. |
| 66 | Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc but excluding ashlars facings dressed stone work and Precast concrete articles, complete all as specified and directed. |
| 67 | M&L for Brick work with Sub class \"B\" bricks straight or curved on plan exceeding 6m mean radius, built in Cement mortar 1:6 complete all as specified and directed. |
| 68 | M&L for Brick work with Sub class \"B\" bricks straight or curved on plan to any radious in half brick thick walls, built in Cement mortar 1:4 complete all as specified and directed. |
| 69 | S&F CPVC tubing 15mm bore with all fittings and fixed complete to wall and ceiling or laid in floors including taking down old steel GI tubing completeall as specified and directed. |
| 70 | S&F CPVC tubing 20mm bore with all fittings and fixed complete to wall and ceiling or laid in floors including taking down old steel GI tubing completeall as specified and directed. |
| 71 | S&F in repair vitreous chinaware wash hand basin flat back of size 550mm x 400mm complete including provision of pair of mild steel angle iron brackets of suitable size duly painted, 32 mm dia chromium plated waste coupling, PVC waste pipe and cutting for pinning in ends of brackets in wall etc complete all as specified and directed. |
| 72 | S&F in repair vitreous china squatting pan (Orissa pattern) long pan size 580x440mm white with integral footrest with \"P\" or \"S\" trap complete (excluding flushing cistern and flush pipe), complete all as specified and directed. |
| 73 | S&Fin repair curtain rail (drapery rod ) 20 to 25 mm dia coloured with pair of suitable brackets, fennals and also making good the wall surface to match the existing surfaces complete all as specified and directed. |
| 74 | S&F in repair looking mirror fitted to wooden plug with CP brass screws, complete all as specified and directed. |
| 75 | S&F in repair 15 mm borestop valve(concealed type, fancy type), cast copper alloy screwed down high pressure with capstain head with long shank & cup complete all as specified and directed. |
| 76 | S&F in repair 15mm dia bib tap long body fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe, fancy type, cast copper alloy, chromium plated long body with flange complete all as specified and directed. |
| 77 | S&F in repair 15mm dia chromium plated wall mixer fancy type with fly nut capstan head screwed for 15mm dia pipe, complete all as specified and directed. |
| 78 | S&F in repair 15mm dia chromium plated wash basin mixer fancy type with fly nut capstan head screwed for 15mm dia pipe, complete all as specified and directed. |
| 79 | S&F in repair 15mm dia chromium plated kitchen sink mixer fancy type with fly nut capstan head screwed for 15mm dia pipe, complete all as specified and directed. |
| 80 | S&F in repair stop valve/ angle valve, fancy type chromium plated cast copper alloy with crutch or butterfly handle screwed down both ends for high pressureas per IS suitable for 15 mm dia iron pipe complete all as specified and directed. |
| 81 | S & Fin repair CP shower rose with shower arm rod complete all as specified and directed. |
| 82 | S&F in repairs PVC low level white flushing cistern, valve less symphonic action type 10 ltr capacity with inlet, ball valve, float and handle including PVC flush pipe 32mm dia bend and a pair of mild steel iron brackets of suitable size including making necessary connection to water supply pip line and, complete all as specified and directed. |
| 83 | Dismantling of floor, hearth or walling including cement mortar bedding (but not backing removing serviceable to store and rubbish off the premises complete all as specified and directed. |
| 84 | M&L for Glazed ceramic colour tiles in vertical surface of size 350 x250x 7 mm or450x 350x7 mmthick set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick cement plaster in CM 1:4 complete all as specified and directed. |
| 85 | M&L for Non Skid ceramic tiles 7 to 8 mm thick(square/ rectangular) area of each tile exceeding 0.18 sq m but not exceeding 0.38 sqm ,in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed or bedding layer inCM 1:6, complete all as specified and directed. |
| 86 | M&L for Non Skid ceramic tiles 7 to 8 mm thick(square/ rectangular) area of each tile exceeding 0.11 sq m but not exceeding 0.18 sqm ,in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed or bedding layer inCM 1:6, complete all as specified and directed. |
| 87 | All as per item 86.00 here-in-before but in skirting/ dado complete all as specified and directed. |
| 88 | S&F in repair stainless steel plate rack made of 0.80mm thick sheet of size 600x750x250mm fixed to wall with suitable rawl plug complete all as specified and directed. |
| 89 | S&F in repair sinks made of stainless steel 0.80mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed. |
| 90 | M & L for green marble 18mm thick (table rubbed and polished) in cooking platform/floor, trades & risers, skirting etc machine cut laid over 20mm thick screed bed or bedding layer in CM 1:4 and jointed and pointed with grey cement mixed with colour pigment to match the shade of the slab including rubbing and poishing and making edges chamfered and demolition of old stone slab of any description, complete all as specified and directed. |
| 91 | Dismantling of PVC water storage tanks exc 500 ltrs & n.exc 1000 ltrs capacity and removing complete all as specified and directed. |
| 92 | S&F rotational moulded polyethylene water storage tanks 500 Ltrs capacity, white coloured, triple layered (cylindrical vertical with closed top) hoisted including nipple and float valve suitable for water tank connection and fixed in position complete all as specified and directed. |
| 93 | Taking down carefully copper/aluminium any type of point wiring (light/fan/socket /power) complete (fittings such as switches, ceiling roses, holders, sockets, regulators light fittings) and making good the disturbed surfaces of wall/floors/ceiling etc)complete all as specified and directed. |
| 94 | Material and labour for concealed point wiring with PVC insulated unsheathed multistranded colour code copper conductor in PVC conduit with FRLS cable1.5 Sqmm size 1100 volts grade conforming to IS:694 in box of 1.6 mm thick including one coat of synthetic enameled black paint and providingwith brass screws and cup washers including single core multi stranded FRLS copper conductor 1.5 Sqmm PVC insulated cable as earth wire to common earth and connected to earth dolly and earth terminal box drawn in same concealed conduit complete all as specified and directed for the following :- |
| 95 | (a)One light/fan/bell point controlled by one way switch 5 amps. |
| 96 | (b)One 3 pin 5 Amps socket outlet point controlled by one way switch on independent board. |
| 97 | (c)One 3 pin 5 Amps socket outlet point controlled by one way switch on same board. |
| 98 | (d)One two way point controlled by 2 way switch 5 amps. |
| 99 | Material and Labour for concealed point wiring with PVC insulated unsheathed multistranded FRLS copper conductor in PVC conduitwith cable 2.5 Sqmm size 1100 volts grade conforming to IS:694 innew metal flush box of 1.6 mm thick including one coat of synthetic enameled black paint with new modular white cover plate with frame of suitable size of required colour fixed with brass screws and cup washers including single core multi stranded FRLS copper conductor 1.5Sqmm PVC insulated cable as earth wire to common earth and connected to earth dolly and earth terminal box drawn in same concealed conduit for One 3 Pin socket 15A Independent board complete all as specified and directed. |
| 100 | S&F of switch piano type 5 amps single pole one way complete all as specified and directed. |
| 101 | S&F of switch pianotype 15 amps single pole one way complete all as specified and directed. |
| 102 | S&F of socket outlet multipurpose 2/3 pin 5 amps flush button type complete all as specified and directed. |
| 103 | S&F of socket outlet multipurpose 2 in 1, 5 and 15 Amps complete all as specified and directed. |
| 104 | S&F of ceiling fan regulator step type for 1200/1400 mm sweep ceiling fan including connections complete all as specified and directed. |
| 105 | S&F 2 way switch complete all as specified and directed. |
| 106 | S&Fbell push switch complete all as specified and directed. |
| 107 | S&Fof electric bell Ding-Dong AC 230 Volt SPwith brass screws and cup washers complete all as specified and directed. |
| 108 | M & L for Decorative City 3 wall light fixture made up of Polycarbonate, suitable for Spiral B-22 Base complete all as specified and directed. |
| 109 | S & F of angle Lamp holder,PVC /Polycarbonate type with back plate and metallic ring suitable for B 22 base complete all as specified and directed. |
| 110 | S&F of LED bulb of 9 watt ,B 22 Base, colour temp 6500K complete all as specified and directed. |
| 111 | Supply, laying and drawing submain wiringin and including 20 mm dia concealed PVC rigid conduits including cutting of chases for laying conduit making good the surfaces as per existing surfaces or as directed on walls 02 runs of IC x 6.00 sqmm (Main Cable and neutral) and one run of IC x 6.0 sqmm (as earth wire) of multistranded copper conductor PVC insulated unsheathed cables of 1100 volts grade conforming to IS : 694 of 1990 complete including connection complete all as specified and directed. |
| 112 | S & F LED light fitting 1X10W bulk head luminaries including driver connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. |
| 113 | S&Fof factory made epoxy polyester powder coated distribution board SP&N 8 way fabricated from minimum 1.6 mm thick CRCA sheet with metal double door (IP-43 protection ) fixed flush to wall and suitable for universal mounting and including 200 Amps copper bus bar, Neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with knockouts and suitable for one DP MCB as incomer and6 SP MCBs as outgoings complete all as specified and conforming to IS: 8623 along with cable end box for aboveDB all as specified and directed.Note: MCBs shall be measured and paid separately. |
| 114 | S&Fof factory made epoxy polyester powder coated distribution board TP & N 4 way (VTPN MCCB DB) with metal double door (IP-54 protection) fabricated from minimum 1.6 mm thick CRCA sheet andfixed on wall and suitable for universal mounting and including 200 Amps copper bus bar, Neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with provn for DPX 160, 4 pole MCCB and ELM as incomerand 12 SP MCBs outgoings complete all as specified and conforming to IS: 8623 along with cable end box for aboveDB including taking down old DBs all as specified.NOTE :-(a) MCBs shall be measured and paid separately.(b) All cables terminating into MCBs shall be connected by using suitable copper lugs/thimbles/sleeves and its cost shall be deemed to be included under respective item of Sch. |
| 115 | S&F inofMCCB 125 Amp 4 pole 16 KA at 415 V with fixed thermal magnetic release complete all as specified directed. |
| 116 | S&Fof single pole MCB 6 to 32 Amps, 240 v, 50 Hz AC Made from moulded self-extinguishing thermostat plastic and suitable for ‘B’ curve, 10 KA breaking capacity complete conforming to IS 8828 of 1996 including taking down old MCB\"s complete all as specified and directed. |
| 117 | S&Fof SPN MCB 32 amp, 240 v, 50 Hz AC Made from moulded self-extinguishing thermostat plastic and suitable for ‘C’ curve, 10 KA breaking capacity, complete all as specified and directed. |
| 118 | Supply and fixing LED lights fitting 1x 20W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. |
| 119 | Supply and fix Air freshenerfan PVC type ventilating single phase 230 voltof 250 mm sweep with louver shutter including making provision for fixing the ventilating fan on window/in wall complete all as specified and directed. |
| 120 | Supply and fixing LED Building security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65 protection complete all as specified and directed. |
| 121 | S&F ceiling rose 3 phase/PVC/polycarbonate isolated body complete all as specified and directed. |
| 122 | S&F single pole and neutral enclosure with a two pin earth plug and socket complete with one single pole MCB 20 Amp complete all as specified and directed. |
| 123 | Supply and Fix HOT press moulded SMC Meter box of inside dimensions 250x250x155 mm with hinged doors and all accessories suitable for fixing 01 nos single phase digital electronic meter dully inside the box complete all as specified and directed. |
| 124 | S&Fof single pole MCB 40 Amps, 240 v, 50 Hz AC Made from moulded self-extinguishing thermostat plastic and suitable for ‘B’ curve, 10 KA breaking capacity complete conforming to IS 8828 of 1996 including taking down old MCB\"s complete all as specified and directed. |
| 125 | M&L far Earthling complete with galvanized steel earth plate electrode 60cm×60cm× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less \"than 1.5 metres below normal ground level, connected to galvanized earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on complete all as specified and directed. |
| 126 | Taking down Geyser 25 Ltr carefully and deposit to MES store with all connected accessories after disconnecting all connection and refixing the same on site carefully complete all as specified and directed. |
| 127 | Taking down carefully Exhaust fan and deposit to MES store with all connected accessories after disconnecting all connection of and refixing the same complete all as specified and directed. |
| 128 | Taking down carefully electric meter and deposit to MES store with all connected accessories after disconnecting all connections and refixing the same complete all as specified and directed. |
| 129 | Fixing only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and directed. |
| 130 | M & L for Painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. complete all as specified and directed. |
| 131 | M&L for opening up the winding of ceiling fan 1200 mm sweep any make and type and rewinding with super enameled copper winding wire, raping insulating material, insertion and varnishing well including drying complete. Testing of the ceiling fan after refixing in position to the entire complete all as specified and directed. |
| 132 | S&F ceiling fan blade 1200 mm sweepmade up of aluminium having provision of free size mounting nuts/screw all as per requirement at site complete all as specified and directed. |
| 133 | Taking down ceiling fan, ceiling cable end, dismantling blades and removing fan and blades and deposit to theMES store yard complete all as specified and directed. |
