|
| 1 | Notes:-(i) 100 percent nonperishable items of the work shall be deposited by the L1 bidder within 30 days after placing of work order.(ii) The critical path network shall be submitted by L1 bidder immediately after the acceptance of tender and approved by GE.(iii) The bidders must ensure to visit the site, check relevant documents and makes of materials required to be incorporated under the subject from concern Engineer-in-Charge.(iv) The unserviceable material obtained under the schedule of credit shall be handed over to the contractor by the Engineer-in-Charge on a proper gate pass.(v) In case of non-availability of any make mentioned under list of Makes, the L1 Bidder shall obtain non-availability / non-manufacturing certificate from the concern OEM / authorised dealers and submitted to Accepting Officer, in such case the L1 bidder may be incorporated makes as approved by HQ CE SWC Jaipur and HQ CE BTZ in the works after prior approval of Accepting Officer.(vi) L1 Bidder shall produce E-way bill alongwith test certificate from OEM / manufacturer for costly items / major items of amount above Rs 50,000/- along with RAR’s and Final Bill.(vii) L1 Bidder shall be maintained an album containing Photos of all the material brought at site and each stage wise work progress and kept at site. Same shall be deposited in Engineer-in-Charge office after completion of work.(viii) The cost of all the above provisions shall be deemed to be included in the quoted rate of bidder, nothing extra shall be paid to the bidder.(ix) If a bidder observes any item in the BOQ that appears to be \"Freakishly Low\" or technically not required for execution at the site, the bidder must submit written comments to the Accepting Officer during the pre-tender stage or at least 07 days before the Bid Submission Start Date. (x) Any act by the contractor that is found to be against the interest of the Department,or commits misconduct or any complaint received through proper channels and supported by verifiable proof (e.g., fraudulent vouchers, negligence in execution, or attempt to cause undue benefit), shall be treated as a willful default.Such defaults shall render the contractor liable for an Adverse Remark (\"NO\") in the Quarterly Work Load Return (WLR), barring the firm and its related/sister concerns from participating in further tenders. |
| 2 | Dismantling asbestos cement corrugated or semi corrugated sheets as in roof covering complete all as specified and as directed. |
| 3 | M&L Pre-painted galvalume aluminium zinc coating AZ-150 GI based corrugated steel sheet 0.6 mm thickCompany Rolled of any colour having tensile strength of 550 Mpaas in roof covering/cladding to wall,fixed with self tapping screws complete all as specified and as directed.MAKE :- TATA DURASHINE/JSW Colouron+/JINDAL Neu Color + or Technocommercial make metioned in Appx \"A\")Note:- Contractor Shall Submit Manufacturer Warranty certificate from manufacturer . |
| 4 | M&L Pre-painted galvalume aluminium zinc coating AZ-150 GI based Plain steel sheet 0.6 mm thickCompany Rolled of any colour having tensile strength of 550 Mpaas in roof covering/cladding to wall,fixed with self tapping screws complete all as specified and as directed.MAKE :- TATA DURASHINE/JSW Colouron+/JINDAL Neu Color + or Technocommercial make metioned in Appx \"A\")Note:- Contractor Shall Submit Manufacturer Warranty certificate from manufacturer . |
| 5 | Dismantling structural steel work as in doors, gate etc etc complete all as specified and directed by the Engineer-in-Charge. |
| 6 | Dismantling unframed timber scantlings 40 sq. cm and over in section, in any position complete all as specified and directed |
| 7 | Demolition of Brickwork or stone/boulder masonry, built in CM or cement lime mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework & precast concrete articlescomplete all as specified and as directed. |
| 8 | M&L brickwork withfly ash bricks, straight or curved in plan exc 6 mtr mean radius built in CM (1:6) using old size bricks complete all as specified and directed by Engr-in-Charge. |
| 9 | Taking down cement or cement lime plaster wall and ceiling including in patches, any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engr-in-Charge. |
| 10 | M&L forrendering 15 mm thick on fair faces of brick or concrete surfacesin cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. |
| 11 | M & L for preparation of newly plastered surfaces of wall & applying two coats of emulsion distemper white or coloured by Roller or Air Spray over 1 mm thick wall care putty(Multipurpose mixer shall be used for uniform and proper mixing of putty)complete all as specified and as directed by Engineer-in- charge.(MAKE :-Tractor Emulsion (Asian Paints), Easy Clean (Berger Paint), Promise Inerior (Dulux Akzonobel) or Techno commercial as mentioned in Appx \"A\". |
| 12 | M&L forrendering 15mm thick on fair faces of brick or concrete surfacesin cement mortar (1:4) finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. |
| 13 | M & L for preparation of newly plastred surfaces of wall,by Vaccume based sanding machine,and applying two coats of exterior emulsion acyrlic weatherproof antifungal paint over a coat of exterior grade primer byAuto Roller over 1 mm thick wall putty, including necessary scffoldings complte all as specified and as directed. MAKE :-(Brand :- Apex Ultima (Asian Paint), Weather Coat ( Berger Paint ), Excel No Dust ( Nerolac) or equivalent brand of Make specified in Appendix \"A\". |
| 14 | M & L providing cement concrete type B1 1:2:4(20 mm graded aggregate)as in lintels upto 1.5m clear span, copings, bed plates (block),cills, steps and other bands, parapet and railing upto 60cm height complete all as specified and directed . |
| 15 | M&L as in repair Anodised aluminium silhouette snap grid with size of grid 605x605mm frame work for false ceiling incl. Hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long and fixing board in ceiling fixed with screw as per manufacturers instructions including demolition of boarding, ceilling board with fram work complete all as specified. |
| 16 | S&F Composite cement designer ceiling board4 mm thick in ( 595 mmX595 mm ) pannel designer ceiling pre finished conforming to IS 14862 type B cateogory three incl powder coatedGI frame , grid work,hold fast,suspended with suspender along with holding down bolt complete . (Note: Ceiling board shall confirming to IS-14862 ,shall be fire resistant , Moisture resistant and ceiling shall be suspended with suspenter and adjuster .) complete all as specified and as directed.Make of Board : Everest /Armstrong/Gyproc (Saint Gobain) or Techno Commercial make as mentioned in Appx \"A\". |
| 17 | Taking down and erection Fixing only Rooftrusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.Note:- Refix the same rafter after raising ht. of bldg complete all as specified and as directed |
| 18 | M & L Granite (of any type) tiles 20mm thick in steps, jambs,pillers, window cill, cooking platform, etc machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing and 15mm thick cement sand screed bed complete all as specified and as directed. |
| 19 | M&L for Stone slab 25 mm to 35 mm thick dressed true and square, in one length not less than 60cm and n. exc 120cm in copings, window cills, chajjas, sunshades, etc., punched dressed on exposed faces and self faced on the embedded unexposed beds and joints; exposed edges rounded or chamfered as directed, set, jointed and pointed in cement mortar 1:4 complete all as specified and directed by Engineer-in-charge. |
| 20 | M&L for steel work as in square / tubular trusses, purlins, post including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS-1161-1979 grade St.-240 including painted with two coat of synthetic enamel paint over a coat of zinc chromate primer paint including preparation of surface at contractor workshop before fabrication complete all as specified and directed by Engineer-in-charge. |
| 21 | S&F Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed by Engineer-in-Charge. |
| 22 | M&L Non skid Ceramic tiles 7 to 8 mm thick (square /rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors on 15mm thick screeding in CM 1:6. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directedNote:- Rates for the work as in repair of chowkhats , GI Tubings or in patches area (n.exc. 5 Sqm) deemed to be included in the item contractor shall not claim extra payment for the same |
| 23 | M&L for providing 75 mm thick cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates as in plinth protection finished even and smooth without using extra cement and providing jointsthroughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight Complete all as specified and as directed. |
| 24 | Dismantling, floor, hearth or wall tiling including CM bedding (but not backing), removing rubbish off the premises complete all as specified and directed |
| 25 | M&L for 7-9mm thick double charged , coloured tiles (square / rectangular), polished, area of each tile not exceeding 0.36 sqm in floors etc, set and jointed with epoxy grout to match coloured to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar (1:6) complete all as specified and directed by Engineer-in-charge. Make :- Johnson/Kajaria/Somany or equivalent technocommercial make as specified in Appendix \"A\".(Note:- Rates for the work as in repair of chowkhats , GI Tubings or in patches area (n.exc. 5 Sqm) deemed to be included in the item contractor shall not claim extra payment for the same) |
| 26 | M&L for 7-9mm thick double charged , coloured tiles (square / rectangular), polished, area of each tile not exceeding 0.36 sqm on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering in cement & sand mortar (1:4) complete all as specified and directed by Engineer-in-charge. Make :- Johnson/Kajaria/Somany or equivalent technocommercial make as specified in Appendix \"A\".(Note:- Rates for the work as in repair of chowkhats , GI Tubings or in patches area (n.exc. 5 Sqm) deemed to be included in the item contractor shall not claim extra payment for the same) |
| 27 | Taking down carefully or drawn out from conduit, existing copper / aluminium point wiring for light, fan, bell, socket, power point etc complete including fixture and fittings such as switches, sockets, ceiling rose, pendent holder, light fittings, top sheet covers, fan regulators, MCB, DB, lamp, earth plug etc (excluding MS sunken boxes) and making good the disturbed surfaces of wall/ceiling complete all as specified and as directed by Engineer-in-charge. |
| 28 | M&L for Modular point wiring complete with 2.5 Sqmm (nominal cross section area) FRLSH PVC insulated multistranded unsheathed copper conductor cable drawn in and including concealed PVC rigid conduit medium grade 20mm dia, pipe hooks, elbows, junction covers and junction boxes including cutting chases in walls for conduits and for sunken pressed steel terminal boxes and making good the disturbed surfaces of wall with all jointing accessories including provision of pressed steel sunken terminal boxes made of 1.2mm thick pressed steel sheet, 60mm deep of suitable length and painted with red oxide primer for mounting modular switches, sockets, fan regulator including suitable size modular plates fixed flush with wall including 2.5 Sqmm PVC insulated multistranded unsheathed copper conductor wire as earth continuity to common earth and connecting to earth dolly for one light point, fan point, bell point controlled by one switch complete all as specified and directed by Engineer-in-Charge.Note : The quoted rate shall be deemed to included with modular cover plates with frame of any colour and metal flush boxes of suitable size as directed by Engr-in-Charge. |
| 29 | S&F Modular switch piano 6 Amps single pole, one way, 01 Module complete all as specified and directed by Engineer-in-charge. |
| 30 | S&F ceiling rose surface bakelite 65mmx50mm with two or three terminal complete all as specified and directed by Engineer-in-charge. |
| 31 | S&F Lamp holder, insulated body with back plate etc complete all as specified and as directed by Engineer-in-Charge. |
| 32 | S&F Energy efficient decorative ultra slim, prewired, lumiline 10 watt LED light fitting (Day cool light), batten type with drive & polycarbonate housing including tube rod and all accessories prewired fixed on wall / hanging complete all as specified and as directed by Engineer-in-charge.Make : Havells Cat Part No.:- LHEXAZP7PN1W010/Crompton Cat Part CCS-103-10-65-SL-DP-NWH/Wipro Cat Part D531065 or equivalent cat part of Make as specified in Appendix \"A\". |
| 33 | S&F Energy efficient decorative ultra slim, prewired, lumiline 20 watt LED light fitting (Day cool light), batten type with drive & polycarbonate housing including tube rod and all accessories prewired fixed on wall / hanging complete all as specified and as directed by Engineer-in-charge.Make : Havells Cat Part No.:- LHEXAZP7PN1W020/Crompton Cat Part CCS-103-20-65-SL-DP-NWH/Wipro Cat Part D532065 or equivalent cat part of Make as specified in Appendix \"A\". |
| 34 | Supply and fixing LED lamp minimum 3 star rated 10W LED B-22 base complete all as specified and directed by Engr-in-Charge with following specifications(a) Lumen system efficacy of lamp should be minimum 100 Lumen per watt.(b) Input Voltage range : 140 to 270 volts(c) Temp operating range : Minus 10°C to Plus 45°C(d) Power factor : Minimum 0.90(e) CRI: Morethan80 |
| 35 | Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed. |
