|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 Sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge |
| 2 | All kinds of soil |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating Each deposited layer by ramming and watering, lead up to 50 and for all lift. |
| 4 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. |
| 5 | Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. |
| 6 | All kinds of soil |
| 7 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: |
| 8 | 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 9 | 1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 10 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement -All work up to plinth level : |
| 11 | 1:1.5:3 (1 cement : 1.5 coarse sand (zone-Ill} derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 12 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement: 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregae 20 mm nominal size derived from natural sources). |
| 13 | Centering and shuttering including strutting, propping etc. and removal of form for |
| 14 | Suspended floors, roofs, landings, balconies and access platform |
| 15 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. |
| 16 | Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 17 | Smooth finishing of the exposed surface of R.C.C. work with 6 mm thick cement mortar 1:3 (1 Cement : 3 fine sand). |
| 18 | Extra for rendering smooth the top of suspended floors, landings and staircases (treads and risers) with cement mortar 1:2 (1 cement : 2 coarse sand), including a floating coat of neat cement and protecting the surface with a layer of 7.5 cm of earth laid over 15 mm of fine sand in case of suspended floor and bricks laid in mud mortar in case of landings and steps, including subsequent removal and cleaning of the same |
| 19 | Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. |
| 20 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : |
| 21 | Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 22 | Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 23 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor Vlevel |
| 24 | Cement mortar 1:4 (1 cement :4 coarse sand) |
| 25 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. Complete at all levels. |
| 26 | Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble |
| 27 | Area of slab over 0.50 Sqm |
| 28 | Granite stone slab of colour black, Cherry/Ruby red |
| 29 | Area of slab over 0.50 Sqm |
| 30 | Granite stone slab of all colour and texture except black, Cherry/Ruby red |
| 31 | Area of slab over 0.50 Sqm |
| 32 | Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete |
| 33 | Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of anysize as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per Sqm, includingpointing in white cement mixed with pigment of matching shade complete |
| 34 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes (weight not less than 10 kg per Sqm) fixing with ISi marked M.S. pressed butt hinges bright finished of required size with necessary screws. |
| 35 | Kiln seasoned selected planks of sheesham wood |
| 36 | 30 mm thick |
| 37 | Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws |
| 38 | 30 mm thick shutters |
| 39 | with ISI marked M.S. pressed butt hinges bright finished of required size |
| 40 | Kiln seasoned selected class of sheesham wood |
| 41 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete |
| 42 | Fixed to steel windows by welding |
| 43 | Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete. |
| 44 | 125 mm |
| 45 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 46 | Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer |
| 47 | Using flats 30x6mm for diagonal braces and central cross piece |
| 48 | Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. |
| 49 | Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) |
| 50 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. |
| 51 | Hot finished welded type tubes |
| 52 | Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete. |
| 53 | Galvanised M.S. Wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides |
| 54 | Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with |
| 55 | 4.0 mm thick glass panes |
| 56 | 5.5 mm thick glass panes |
| 57 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. |
| 58 | 40 mm thick with 20 mm nominal size stone aggregate |
| 59 | Cement concrete pavement with 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size), including finishing complete |
| 60 | Providing and fixing glass strips in joints of terrazo/ cement concrete floors. |
| 61 | 40 mm wide and 4 mm thick |
| 62 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/Sqm including pointing the joints with white cement and matching pigment etc., complete |
| 63 | Providing reinforced by organic fibres and/or inorganic synthetic fibres cement 6 mm thick corrugated sheets (as per IS: 14871) roofing up to any pitch and fixing with polymer coated J or L hooks, bolts and nuts 8 mm dia. G.I. plain and bitumen washers or with self drilling fastener and EPDM washers etc. complete (excluding the cost of purlins, rafters and trusses), including cutting sheets to size and shape wherever required |
| 64 | Providing gala 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design |
| 65 | In 75x75 mm deep chase |
| 66 | Providing and fixing precoated galvanised iron profile sheets (size, shapeand pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per Sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 67 | 12 mm cement plaster of mix : |
| 68 | 1:4 (1 cement: 4 coarse sand) |
| 69 | 1:6 (1 cement: 6 coarse sand) |
| 70 | 15 mm cement plaster on rough side of single or half brick wall of mix : |
| 71 | 1:4 (1 cement: 4 coarse sand) |
| 72 | 1:6 (1 cement: 6 coarse sand) |
| 73 | 6 mm cement plaster 1:3 (1 cement : 3 fine sand) finished with a floatingb coat of neat cement and thick coat of Lime wash on top of walls when dry for bearing of R.C.C. slabs and beams |
| 74 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge |
| 75 | With cement mortar 1:4 (1cement: 4 coarse sand) |
| 76 | Fixing chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts, embedding hold fasts in cement concrete blocks of size 15 x 10 x 10 cm with cement concrete1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. |
| 77 | Door chowkhats . |
| 78 | Window chowkhats . |
| 79 | Making the opening in brick masonry including dismantling in floor or walls by cutting masonry and making good the damages to walls, flooring and jambs complete, to match existing surface including disposal of mulba/ rubbish to the nearest municipal dumping ground, all complete as per direction of Engineer-in-Charge |
| 80 | For door/ window/ clerestory window |
| 81 | Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: |
| 82 | Float glass panes of nominal thickness 4 mm (weight not less than 10kg/Sqm) |
| 83 | Float glass panes of nominal thickness 5 mm (weight not less than 12.5kg/Sqm) |
| 84 | Renewing glass panes, with wooden fillets wherever necessary |
| 85 | Float glass panes of nominal thickness 4 mm (weight not less than 10kg/Sqm) |
| 86 | Float glass panes of nominal thickness 5 mm (weight not less than 12.5kg/Sqm) |
| 87 | Renewal of old putty of glass panes (length) |
| 88 | Refixing old glass panes with putty and nails |
| 89 | Raking out joints in lime or cement mortar and preparing the surface for re-pointing or replastering, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge |
| 90 | Providing and fixing bright finished brass helical door spring (superior quality). |
| 91 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. |
| 92 | Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 93 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge |
| 94 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. |
| 95 | In cement mortar |
| 96 | Removing mortar from bricks and cleaning bricks including stacking within a lead of 50 m (stacks of cleaned bricks shall be measured): |
| 97 | From brick work in cement mortar |
| 98 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : |
| 99 | Of area 3 sq. metres and below |
| 100 | Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead |
| 101 | Of area 3 sq. metres and below |
| 102 | Dismantling steel work manually/ by mechanical means in built up sections without dismembering and stacking within 50 metres lead as per direction of Engineer-in-charge |
| 103 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. |
| 104 | For thickness of tiles 10 mm to 25 mm |
| 105 | Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead |
| 106 | Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: |
| 107 | G.S. Sheet |
| 108 | Asbestos Cement sheet |
| 109 | Dismantling C.I. or asbestos rain water pipe with fittings and clamps including stacking the material within 50 metres lead : |
| 110 | 75 to 80 mm dia pipe |
| 111 | 100 mm dia pipe |
| 112 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 113 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. |
| 114 | Brick edging in full brick width and half brick depth including excavation, refilling and disposal of surplus earth lead upto 50 metres |
| 115 | With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 116 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : |
| 117 | Kitchen sink without drain board |
| 118 | 610x460 mm bowl depth 200 mm |
| 119 | P/F stainless steel first quality curtain rod with all fitting and fixture i/c bracket and all other necessary accessories complete as per direction of engineer in charge. |
| 120 | Providing and fixing 25mm dia meter curtain rods of 1.25mm thick brass plates with two brass brackets fixed with brass screws and PVC plugs etc. wherever necessary complete . |
| 121 | Fixing of old girder or grill in position including welding, drilling, cutting etc. complete as per direction of EIC (labour rate only) |
| 122 | Dismantiling CC Floor Nominal Concrete 1:3:6 or richer mix (i/c equivalent design mix) i/C base concrete Nominal Concrete 1:4:8 or leaner mix (i/C equivalent design mix) manually by mechanical means including disposal of material withing 50 meters lead as per direction of EIC. |
| 123 | Grinding of Existing Stone Floor/DADO/Skirting including polishing complete in all respect. |
| 124 | S/F of MS steel shutter Almirah type made from 1.0mm. Thick MS Sheet including frame hold fast mortise handle lock with double key looking mirror frame steel pegs on back side and i/c hammer painting of approved shade on front and three coats of synthetic enamel paint at backside i/c grouting in wall with 1:2:4 cement concrete i/c supply of all material labour & T&P etc. required for proper completion of the work |
| 125 | Providing laying and jointing 110 mm dia UPVC pipe of Ist quality complete in all respect as as per direction of EIC |
| 126 | Providing laying and jointing 75 mm dia UPVC pipe of Ist quality complete in all respect as as per direction of EIC |
| 127 | Providing and fixing aluminium sheet 0.50 thick on existing door shutter (Bathroom and WC door) using nails |
| 128 | Providing, mixing and applying 12 mm thick ready mix cement plaster of approved makeas per specifications and directions of Engineer-in-charge. |
| 129 | Providing, mixing and applying 15 mm thick ready mix cement plaster of approved makeas per specifications and directions of Engineer-in-charge. |
| 130 | Brick work with old bricks (supplied free of cost at our stores ) in foundation and plinth in cement mortar 1:4 (1 cement : 4 coarse sand) |
| 131 | Brick work with old bricks (supplied free of cost at our stores ) in foundation & plinth in cement mortar 1:6 (1 cement: 6 coarse sand) |
| 132 | Providing and fixing 35 mm thick ISI mark ply flush door shutters non-decorative type of century ply make or equivalent approved make complete in all respects as per directions of EIC |
| 133 | Providing and fixing 32 mm thick ISI mark flush door shutters non-decorative type of centuryplymake or equivalent approved make complete in all respects as per directions of EIC |
| 134 | Providing and fixing S.S. Sliding door bolt of 200x16 mm with nuts and screw etc. complete as per direction of EIC |
| 135 | For Calculation purpose Only |
| 136 | Sub Total (A) |
