|
| 1 | (B/R PORTION)Complete removal of entire existing water proofing treatment in any position, any thickness including tarfelt, Plaster, lean concrete, gravels etc. and removing the debries out side MD land complete all as specified and directed. |
| 2 | M&L for plain cement concrete type B1, 1:2:4 (20mm graded stone aggregate) as in kerb or mud stop, slightly rounded or champhered on edges complete all as specified and directed. |
| 3 | M&L for plain cement concrete type B1 1:2:4 (20mm graded aggregate) 40mm thick complete all as specified and directed. |
| 4 | M&L for 10 mm thick rendering in CM 1:4 over concrete surfaces mixed with water proofing compound @ 3% by weight of cement complete all as specified and directed. Note: Water Proofing compound shall be measured and paid for seprately as \"Supply Only\" |
| 5 | M&L Acrylic emulsion polymerof acrylic single component low viscosity polymer for preventing leakages over exisitng/New surface of slab, terrace, exterior, interior wall, Chajjas etc as per following procedure :-(a) Surface & surface preparation : Remove all the loose particles, dirt & dust clean by water, wire brush & mechanical cleaning, grease & oil should be cleaned using solvents,if the surface is previously coated with tar, it should be thoroughtly scraped off.The surface should be dry before application.All the cracks and crevices in the concrete slab to be filledwith polyurethene based sealent with and including application of PU based primer complete all as specified and directed.(b) Finish paint : Apply water based polyurethenene modified dispersion (single component cold applied, non toxic, VOC compliant) in 03 coats icluding 01 coat of primer of same materials after dillution of water at 50 % or specific primer matching same material as per manufacturers specification complete all as specified and directed. |
| 6 | Dismantling plain or corrugated steel sheeting any gauge thickness including Nainital or similar pattern roof covering complete all as specified and directed.. |
| 7 | S&F pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering /cladding to wall, fixed with self tapping screws as specified complete all as specified and directed. |
| 8 | M&L Fibre board Eves/ Weather Boarding 12 to 20mm thick or Feather Edged 15mm to 20mm thick and fixed with 30mm Lap, complete as approved arch pattern any size and shape including taking down existing boarding including necessary scaffolding required for maintance work, safety measures etc complete all as specified and directed. |
| 9 | Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets/ AC boards, any thickness, including cover fillets complete all as specified and as directed. |
| 10 | M&L for false ceiling with powder coated exposed Aluminium grid suspension system (E-Grid T-2430 or equivalent load carrying capacity with mid span deflection not exceeding 1/360 span with hanger spacing of 1200 mm c/c) consisting of Main Runner 3600 mm long, Cross Tee 1200mm/600mm long and Wall Angle. The Wall Angle shall be fixed on PVC Dash Fasteners on the perimeter of the wall by steel screws with distance 300 mm c/c. The Main Runners to be placed @ 1200mm, The Cross Tee 1200mm will be inserted in the pre-cut slots of Main Runner at a regular interval of 600 mm to form a modular grid of 1200mm x 600mm. Additional Cross Tees of 600 mm shall be placed perpendicular to the Cross Tee 1200 mm long to finally form a grid of 600mm x 600mm. Grid of module size 600mm x 600mm shall be supported by 6 mm dia G.I. wire from purlins/ soffit complete all as specified and directed . |
| 11 | M & L for providing4 mm thick high pressure steam cured everest water repellentnon asbestos fibre cement standard ceiling board ( density > 1200 kg/ Cum, modulus of rupture (M.O.R) -15.85 MPa, thermal condutivty (K)-0.0872W/mK) confirming to IS 14862 of size 595 mm X 595 mm shall be place in grid module to form false ceiling complete all as specified and directed . |
| 12 | Demolition of brickwork or stone masonary built in cement mortar inlcuding all quions, arches, pillars etc. but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed . |
| 13 | M&L for stone walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortor 1:6 complete all as specified and directed. |
| 14 | Extra over stone walling for hammer dressing to face stones with maximum depression on face from a straight edge n.exc 40mm and dressing face beds and joints as specified to randomrubble wallingbrought upto courses complete all specified and directed. |
| 15 | M & L for racking out joints/ pointing to old random rubble or polygonal rubble masonry uncoursed or brought up to courses buit in cement or cement lime mortar complete all as specified and directed . |
| 16 | M&L for keyed pointing to randomor polygonal rubble uncoursed or brought upto courses in cement mortar 1:4 complete all as specified and directed. |
| 17 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed . |
| 18 | M & L forplain cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in floor levelling course and in similar situations 25 mm thick complete all as specified and directed . |
| 19 | M&L for non-skid coloured ceramic tiles 7 to 8 mm thick (Square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles complete all as specified and directed . |
| 20 | M&L for Non Skid Ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6 complete all as specified and directed . |
| 21 | M&L Glazed ceramic coloured tiles in vertical surfaces 300 x 450 x 7mm as in dado/ skirting etc. and joineted neat in cement slurry and pointed in white or colour cement to match over 10mm thick backing coat in CM 1:4 complete all as specified and directed . |
| 22 | M&L for 20mm thick machine cut kota stone slab flooring laid over and including 20mm thick screed base in CM 1:6 and jointed in with grey cement to match the shade of the slab including rubbing, cutting and polishing complete including preparation of old surfaces complete all as specified and directed. |
| 23 | M&L for 20mm thick machine cut kota stone slab as in riser of steps, skirting, dado and pillar laid over and including 15mm thick rendering in CM 1:4 and jointed with grey cementslurry mixed with pigment to match the shade of the slab inlcuding rubbing, cutting and polishing complete all as specified and directed. |
| 24 | Demolition of cement concrete in floors and pavings n. exc. 15cm thickness (below or above ground level) complete all as specified and directed. |
| 25 | M&L for 75mm thick PCC 1:3:6 type C2 using 20mm graded stone aggregate as in plinth protection. complete all as specified and directed. |
| 26 | M&L for Machine cut cudappah stone slab 20 to 25mm thick over 20 mm th cement screed base in cm 1:6, laid and jointed with grey cementslurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. |
| 27 | Taking down chowkats or frames of wooden or steel window not exc 1.5 sqmwith Shutters (without taking off shutters from the frames) complete all as specified and directed. |
| 28 | Taking down chowkats or frames of wooden or steel windowexc 1.5 sqmbut not exc 4.00 Sqmwith Shutters (without taking off shutters from the frames) complete all as specified and directed. |
| 29 | Taking down shutters of any description but exc. 1 Sqm and n exc. 2 Sqm each complete all as specified and as directed. |
| 30 | S&F steel windows with double door side hung shutters (Glazing shutters & Jali Shutters) including projecting type hinges with steel handles, steel peg stays complete withglazing shutters with bars &outer shutters as as fly proof shutters complete all as specified and directed. |
| 31 | S & F Steel ventilator with top hung shutter including hinges, steel peg stay complete all specified and as directed. |
| 32 | M & L sheet glass ordinary quality 4mm thick and glazing with oil putty in squares exc. 0.5 sqm each pane complete all as specified and directed. |
| 33 | S&F 2nd class Hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed. |
| 34 | S & F 125 x 60mm size pressed steel frames for doors with one or more rebates incl necessary fixing luges, hinges, lock strike plates etc. complete all as specified and directed. |
| 35 | M&L for PCC 1:3:6 type C1 (using 20 mm graded stone aggregate) as in door frame filling and similar work filling complete all as specified and directed. |
| 36 | M&L for 35mm thick Factory Made Flush shutters with lipping all around of solid core construction with block board core and ply wood face panels commercial type on both side complete all as specified and directed. |
| 37 | M&L for 35mm thick 2nd class H/wood gauged and skeleton shutters, open rebated and prepared to receive gauge etc (with sash bars) edges of ramming plain, chamfered or grouted, fitted with cut of and mitred beads for securing gauge etc of size of members of shutters as specified in SSR Part-I section 8 clause No. 8.2(a) and fitted to chowkats complete all as specified and directed. |
| 38 | S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm & fixed with stainless steel wire staples complete all as specified and directed. |
| 39 | S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail.Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, and fixing in the frame at site complete all as specified and directed. |
| 40 | S & F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S square tube, complete all as specified and directed. |
| 41 | M&L for two coat of synthetic enamel paint over a coat of pink primer including preparation of new/old painted wood surfaces complete all as specified and directed. |
| 42 | S& F 300 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed. |
| 43 | S&F aluminium anodised barrel tower bolts of extruded section 200 mm long. complete all as specified and directed. |
| 44 | S&F aluminium handles, anodised, cast type, of size 150 mm complete all as specified and directed. |
| 45 | S & F 140 mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed. |
| 46 | S&F 300mm, Brass ordinary rat tail rod pattern springs including roller and roller plate including fixing to door complete. complete all as specified and directed. |
| 47 | S&F in repairs 25mm dia powder coated aluminium draping rods corrugated of approved qualityincluding brackets with dome complete all as specified and directed. |
| 48 | Taking down cement plaster, any description on brick, concrete or stone walls or ceiling including racking out joints, hacking for key, scrubbing down with water etc and removal of rubbish offthe premises complete all as specified and directed. |
| 49 | M & L for Rendering 15mm thick in two layers, 5mm thick using WPC @ 3% by weight of cement over 10 mm thick on stone masonary work/ concretesurfaces in cement mortar 1:4 finished surfaces even and smooth without using extra cement,complete all as specified and directed. |
| 50 | M&Lfor rendering 15 mm thick plaster in CM (1:6) on wallsurface finished even and smooth without using extra cement complete all as specified and as directed. |
| 51 | Supply only WPC complete all as specified and directed. |
| 52 | M & L for three coat of white wash onwall surface including preparation ofsurfaces complete all as specified and directed. |
| 53 | M & L three coat of white wash onceiling surfaces including preperation ofsurfaces complete all as specified and directed. |
| 54 | M&L fortwo or more coats of 100% Premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @1.43 litre/10sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 Sqm over Old/ new surfaces of wall including necessary scaffolding required for painting work, safety measures etc. complete all as specified and directed. |
| 55 | S&F in repair 18mm thick prelaminated particle board interior grade, conforming to IS-12823, Gde-I prelaminated both side with decorative choice lamination as in cupboard shutters, Kitchen cabinets etc fixed with screw including 3mm thick, ist class HW(TW) beading all around on edging to timber frame work complete all as specified and directed. |
| 56 | S&F continuous (Piano) hinges mild steel bright finished or electro galvanised width of flap 30mm complete all as specified and directed. |
| 57 | S&F in repairs vitreous china water closet (squatt pan) orrisa pattern 580x440 mm sizewhite withfront or back inlet with integral foot rests including provn of lime concrete bedding including connections to flushing cistern/ pipe complete all as specified and directed. |
| 58 | S&F in repairs 10 liters capacity PVC low level flushing cisternwith ISI marked body,complete all as specified and directed. |
| 59 | S&F in repair Wash hand basin, vitrous china, coloured,flat back of size 550 x 400mm including cutting for and pining in ends of brackets or erecting stand including brass waste coupling, waste pipe, 15mm dia bore pillar taps, chromium plated fancy type and connection pipe complete all as specified and directed. |
| 60 | S & F looking mirror 600 x 450mm beveled edge mirror of selected quality glass mounted on 6mm thick commercial plywood and fixed to wooden plugs with steel screw, complete all as specified and directed. |
| 61 | S&F in repairs Bib taps fancy type chromium plated for 15mm bore pipe,(small/long body) screwed for iron pipes or for brass ferrulecomplete all as specified and directed. |
| 62 | S&F in repairfancy type, chromium plated angular stop cock fixed with wall flange for 15mm bore of pipe complete all as specified and as directed. |
| 63 | S&F in repairs 15 mm bore stop valves, cast copper alloy, chromium plated, with long shank and cup (concealed type) fancy type screwed down, high pressure, with crown head, screwed both ends for iron pipe or for unions complete all as specified and directed. |
| 64 | S&F in repairs 450mm long PVC connection 15mm bore with PTMT nuts complete all as specified and directed. |
| 65 | S &Ffor 100mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete complete all as specified and directed. |
| 66 | S & F stainless steel grating doom 100 mm dia complete all as specified and directed. |
| 67 | S & FSheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf corner type three tyres with chromium plated brackets, bracket guard and railing 30cm size incl screws, fixed as in repair complete all as specified and directed. |
| 68 | S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete complete all as specified and directed. |
| 69 | S&F in repair 125mm chromium plated shower roses with shower arm with or without swivel joints, any size including fixing to uPVC/Steel pipe complete complete all as specified and directed. |
| 70 | S&F in repairs stainless steel kitchen sink of overall size 495x420mm and bowl size 410 x 330 x 160mm with plugs,washers and wastes;32 mm dia Low density polyethylene (LDPE) pipes of pressure rating 6 kgf/sq. as in waste pipe including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe complete all as specified and directed. |
| 71 | S&F in repairs 60 cm long brass CPtubular towel rail 20-mm diaD type complete all as specified and directed. |
| 72 | S&F stainless steel chromium plated 6 Pin, 45Cm to 60Cm long hanger fixed to wall with screws complete complete all as specified and as directed. |
| 73 | S&F for steel water tubes, 20mm bore medium grade, galvanized with all fittings and fixed complete to walls, ceiling or laid in floor, complete including taking up or down steel tubing and connections or removal to store complete all as specified & directed. |
| 74 | All as per itemhere in above but 15mm dia complete all as specified and directed. |
| 75 | M&L for cutting chases, pinning in stone, concrete block walls making good to facings where required and pointing in cement mortar 1:3 to concealed water tubingand making good complete all as specified and directed. |
| 76 | S&Fin repairs 1000 ltrs capacity, Rotational moulded polythylene water storage tank (cylindrical vertical with closed top) hoisted and in position including ball brass valve 20mm high pressure with polythene float and fly nut complete including dismantling existing water tank and removing to store complete all as specified and directed. |
| 77 | S &F Gun metal globe or gate valve with iron wheel head screwed both ends size 20mm for iron pipe, fixed complete all as specified and directed. |
| 78 | S&F PVC (SWR) pipes, single socketed in any length with rubberring joints fixed to wall, floor of size 110mm bore including taking down old pipe complete all as specified and directed. |
| 79 | S&F PVC (SWR) pipes, single socketed in any length with rubberring joints fixed to wall, floor of size 75mm bore including taking down old pipe complete all as specified and directed. |
| 80 | S&F PVC (SWR) junction, (Single Tee) equal or unequal 110mm bore complete all as specified and directed. |
| 81 | S&F PVC (SWR) junction, (Single Tee) equal or unequal 75mm bore complete all as specified and directed. |
| 82 | S&F PVC (SWR) bends of any radius 110mm bore complete all as specified and directed. |
| 83 | S&F PVC (SWR) bends of any radius 75mm bore complete all as specified and directed. |
| 84 | S&F PVC (SWR) vent cowl 110mm bore complete all as specified and directed. |
| 85 | S&F PVC (SWR) vent cowl 75mm bore complete all as specified and directed. |
| 86 | S&F PVC (SWR) gully traps 125/100mm setting and jointed in cement solventcomplete all as specified and directed. |
| 87 | S&F Structural steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes confrming to IS 1161-1979 grade St-240 with necessry angle cleats and girder plate etc complete all as specified and directed. |
| 88 | M&L for Two coats of synthetic enamel paint over a coat of red oxide on steel surfaces exc. 10 cm width or girth etc. complete all as specified and directed. |
| 89 | Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided forcomplete all as specified and directed. |
| 90 | M&L for providing plain cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed. |
| 91 | M&L for PCC 1:3:6 type C 1 ( using 20 mm graded stone aggregate) as in surface channels and bed of drains complete all as specified and directed. |
| 92 | Demolition of brick work or stone masonry/ PCC block walling built in cement mortar or cement lime mortar incl arches, pillers etc. complete all as specified and directed. |
| 93 | M&L Fly ashbrick work straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed. |
| 94 | Demolition and breaking up 150 mm bore drain pipes (SWG,AC or RCC pipes) set in CMcomplete all as specified and as directed. |
| 95 | Supply and laying reinforced cement concrete pipe 150mm bore class NP-2 with collars laid and jointed with cementcomplete all as specified and directed. |
| 96 | M & L for providing bed to drain pipes 150 mm dia in cement concrete (1:3:6) type C2 using 40 mm graded stone aggregate including packing under and haunching against the sides of pipe after they are laid & tested complete all as specified and directed. |
| 97 | S&F factory made 50mm thick 600 x 600 mm manhole cover (125Kg, 10 Ton capacity) with additional frame for fixing, of precast RCC 1:2:4 type B1 (using 20mm graded stone aggregate) finished the surface even and fair including reinforcement as per manufacturer\"s design and set in CM 1:4 and handles including demolition of old existing RCC cover (Reinforcement required to cut as facilitate to demolition) of any description and in any position complete all as specified and directed. |
| 98 | M&L forrendering 15 mm thick on other than fair faces of brick or concrete surfaces in CM (1:4), finishing even and fair without using exta cementcomplete all as specified and directed. |
| 99 | Cleaning of 150 mm bore sewage line in between two consecutive manholes to the entire satisfaction of Engg-in-Charge and testing by pouring water from manhole to manhole. Complete all as specified and directed. |
| 100 | Cutting into existing manholes for concreting new drain of 150mm internal dia making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2;4 type B1 smooth finished and reforming benching as required.complete all as specified and directed. |
| 101 | (E/M PORTION)Taking down carefully aluminium/ copper point wiring any type for one light , fan, socket power point or buzzer controlled by one switch complete including fitting/ fixtures such asswitches, ceiling roses, holder, socket, light fitting etc; for credit and making good disturbed surfaces of walls, ceilings etc complete all as specified and directed. |
| 102 | Taking down old U/s DBs including all fittings or switches of any type and any size. complete all as specified and directed. |
| 103 | M & L for point wiringwith 1.5 Sqmm multi stranded copper conductor 1100 V grade, ISI marked, PVC insulated unsheathed cable (with approved colour code) FRLSH cable drawn in & including PVC casing caping (ISI Mark)of size 20/25 mm on wall or over ceiling/surface (or as at site requirement with casing caping as per direction of Engr-in-Charge), including sutable size of metal flush box any size and respective cover plate all as specified including 1.5 Sqmm FRLSH PVC insulated sheathed solidmulti stranded copper conductor cable/wire for continoues earth wire in green colour and connected to earth dolly forlight point/ceiling fan point /exhaust fan point / bell point controlled by one switch.Note:- 1. M&L forcutting chases if required on walls / ceiling /surface and making good disturbed surfaces including finishing with cement mortar (1:3) etc; are deemed to be included in the quoted rate. complete all as specified and directed. |
| 104 | All as per item herein above but for 3 pin 5 Amps switch socket combination on independent board with 1.5 sq mm copper cable. complete all as specified and directed. |
| 105 | All as per item herein above but for 5 Amps socket point on the same board controlled by one switch with 1.5 Sqmm copper cable complete all as specified and directed. |
| 106 | All as per item herein above but for 16/20 Amps socket point conform by one switch with 4.0Sqmm copper cable complete all as specified and directed. |
| 107 | All as per item herein above but for One light point controlled by two 2-way switches with 1.5 sq mm copper cable.complete all as specified and directed. |
| 108 | S & F Modular switch 1 way 6/10 Amp SP, 1 module complete all as specified and directed. |
| 109 | S & F Modular switch 2 way 6/10 Amp SP, 1 module complete all as specified and directed. |
| 110 | S & F Modular switch 1 way 16/20 Amp SP, 1 module complete all as specified and directed. |
| 111 | S & F Modular Fan step regulator, 120W - 2 module complete all as specified and directed. |
| 112 | S & F for ceiling rose surface bakelite 3 phases polycarbonate isolated body complete all as specified and directed. |
| 113 | S & F Modular Socket 6 A 2/3 pin combined, 2 module complete all as specified and directed. |
| 114 | S & F Modular Socket 6 A /16 A-2/3 pincombined 2 module complete all as specified and directed. |
| 115 | S & F Modular Bell push switch 6 Amp1 module complete all as specified and directed. |
| 116 | S & F Bell Buzzer/Ding Dong AC. 230 volts, single pole complete all as specified and directed. |
| 117 | Supply & fix LED Tube light luminaires, 20 watts, lumen output not lessthan 2000 (4 feet), made of anodised extruded aluminium housng, with high transmissivity diffuser, high lumen output, with suitable integrated electronic driver, and operated in single phase, 230 volts, 50HZ, all accessories internally pre-wired and including connecting up with three core twisted flexible copper conductor cable offrom connector and ceiling rose complete all as specified and directed. |
| 118 | Supply and fixingLED bulb not less than 15 watt B22 type emergency inverter type rechargable (4 hr backup) with lumen output 950 lm and color temp 6500K suitable for bulb holdercomplete all as specified and directed. |
| 119 | Supply and fixing Lamp holder (Angle Holder), PVC/ Polycrbonate type with cord grip cap suitable for pendent fitting complete all as specified and directed. |
| 120 | Supply & fix of new generation energy saving and environmental friendly long life 45 W LED building security light made up of pressure die cast aluminium housing with high efficient LED as lighting source and PC cover having top Opening seperate driver compartment with IP66 protection and impact resistance of IK07including necessary brackets (made out of suitable bore GI pipe light grade appx 0.6 meter long bend to shape) nuts, bolts, etc fixed on walls with MS clamp complete all as specified and directed. |
| 121 | M&L for sheet metal enclosure MCB DBs VTPN, 4 way 415 V, with 250 A rated copper bus bar, double door, IP 43, suitable for 160 Amp MCCB 25 kA as incomer as per IEC 61439-3, suitable for flush mounting and surface mounting including taking out complete all as specified and directed. |
| 122 | S &F MCCB 4 Pole , 415 V , AC , C - curve , Adjustable type, 100 Amps with breaking capacity 25 KA complete all as specified and directed. |
| 123 | M&L for sheet metal enclosure MCB DBs SPN, 8 way 240 V, with 100 A rated copper bus bar, double door, IP 43 as per IEC 61439-3, suitable for flush mounting and surface mounting including taking out complete all as specified and directed. |
| 124 | M & L for MCB SP 6-32 Amps, 240 volts, 10 kA ISI marked as per IS/IEC 60898-1 2002, C - curve, IP 20 including taking out complete all as specified and directed. |
| 125 | M & L for MCB SPN 32/40 Amps, 240 volts, 10 kA ISI marked as per IS/IEC 60898-1 2002, C - curve, IP 20 including taking out complete all as specified and directed. |
| 126 | Taking down burnt/unserviceable sub main wiring any size complete and making good disturbed surfaces of walls complete all as specified and directed. |
| 127 | M & L for sub main wiring with two single core FRLSH, PVC insulated unsheathed, 1100 Volts grade, copper cable 4 sqmm stranded conductor and drawing through PVC casing caping ( ISI marked) of suitable size withaccessoriesincluding continus earth wire FRLSH, PVC insulated unsheathed 1100 volts grade, cable 4 sqmm copperconductor and connected to common earth dolly complete as directedincluding taking down old submain wiring and making good disturbed surface matching with the existing shade/tint. Complete all as specified and directed.Note :-(i) One run of casing caping, two runs of cable and one run of earth wire shall be measured and paid as one unit. |
| 128 | All as per herein above item but for2x1.5 sq mm and 1x1.5 sq mm as earth wire. complete all as specified and directed. |
| 129 | M&L for Removing the existing Ceiling fan and servicing, cleaning and spray painting, rewinding & refixing the same with necessary 3 core wire and accessories all as directed. |
| 130 | S&F Blades for 1200 mm ceiling fan in place of unserviceable blades including required nuts/washers etc. complete all as specified and directed. |
| 131 | S&F Canopy for 1200 mm ceiling fan in place of unserviceable Canopy including required nuts/ washers etc. complete all as specified and directed. |
| 132 | S&F down rod 2 feet for 1200 mm ceiling fan in place of unserviceable downrod including required nuts/washers/pins etc.complete all as specified and directed. |
| 133 | S & F exhaust fan made of PVC body minimum 250 mm sweep with louvers shutter 240 Volt , 50 Hz ,single phaseaccessories, complete all as specified and directed. |
| 134 | Taking down the existing electric meter of Single Phase/ Three phase any capacity and make after disconnecting electrically and S&F new electric meter box (Polycarbonate body suitable for installation of4 x electric meter in one box or as recommended by Engr-in-charge) suitable for 3 phase/single phase electric meter including refixing of electric meter in new meter box after servicing & removing of old u/s meter box and made good the discturbed surfaces ccomplete all as specified and directed. |
| 135 | M&L for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cmx 6mm thick buried directly in ground (earth pit not less than 2.25 metre below ground level) with top edge of the earth plate not less than 1.5 metre below ground level, connected to GI earth wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanisediron or steel all as shown in electrical plate No 3 of SSR Part Iconnected to earth test point all as specified including excavation and connected earth work, in soft/loose soil, removing soil upto 50m, PCC1:3:6 type C1 as in pit, 20mm dia GI pipe medium grade for watering pipe, 15mm bore GI medium grade earth lead protection pipe,50mm thick RCC 1:2:4 type B1 cover slab of earth pit reinforced with 8 mm dia TMT Bars @ 10cm C/C both ways and with handle made out of 12mm dia bars,funnel, strainer, alternate layer of charcoal dust and common salt and testing on completion, complete all as specified and directed. |
| 136 | Taking out LT UG Cable any size inany type of soil complete all as specified and directed. |
| 137 | Supply, laying, jointing and testing LT cable in trenches or on poles/ walls, XLPE Insulated screened, PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 70 sqmm 3.5 corefor laying in trenches and poles /walls complete all as specified and directed. |
| 138 | As per item hereinabove but for size 35 sqmm 3.5 core. complete all as specified and directed. |
| 139 | Supply & fixing DWC Pipe heavy dutyminimum 32/40 mm dia of required length for protection of cables complete including necessary MS clamps, nuts, boltsfixed complete to walls and ceilings or laid in floorscomplete all as specified and directed. |
| 140 | Supply & fixing GI Pipe light grade 50 mm dia, ISI marked, of required length for protection of cables complete including necessary MS clamps, nuts, bolts and washers etc fixed complete to walls and ceilings or laid in floorscomplete all as specified and directed. |
| 141 | Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m wide and not exceeding 1.5 m depth and getting out in any type ofsoil for laying cables/ pipes/ erection of poles etc. complete all as specified and directed. |
| 142 | Removing excavated material (soil) not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point. complete all as specified and directed. |
| 143 | Returning filling in soil including spreading levelling watering well ramming in layers not exceeding 25 cm each. complete all as specified and directed. |
| 144 | M&L for cutting of bituminous road/floor for laying of pipe/cables not exceeding 30 cm wide and not exceeding 60 cm deep including refilling/ with material and watering well ramming/compacting and making good with PCC 1:2:4 type B-1, 100 mm thick complete all as specified and directed. |
| 145 | Supply Fabricate, install, connect, test and commission Outdoor type dust & Vermin proof LT electrical panel board, 1100 volts, 50 Hz AC supply, fully compartmentalised for cable chamber and busbar 300 Amps 4 Nos including MCCB 4P 160 Amps as incommer,chambers with adequate space made out of 3 mm thick CRCA sheet for load bearing like all over body, front and back cover with hinges and aldrops with DC locks CRCA poweder coated and 2.0 mm thick MS Sheet for non load bearing and portions, complete with one coat of powder coating including suitable angle iron/ flat iron frame work/ supports bottom 50x50x6 mm MS channel as base and chamber for metering equipment complete suitable for mounting following switch gear items internally connected with suitable capacity aluminium strip/ rods insulated and connection wirings with FRLS copper conductor complete mounted on PCC pillars foundation, arrangements for bus bar trunking system, cable connectionusing new lugs complete with danger notice all as specified(ii) Getting of approval for Panel board drawing from Engr-in-Charge is necessary before fabrication. (iii) All swith gears should be fixed with 06 mm thick Fibre sheet Make: Any CPRI approved complete all as specified and directed. |
| 146 | Material and Labour for Earthing complete with with600 mm x 60 mm x 6.15 mm thick, galvanized steel earth plate electrode buried vertically in ground (not less than 2.25 meters deep below normal ground level),with top edge of earth plate not less than 1.5 meter below ground level connected to and including G.I strip of size 25mm x 4 mm by means of bolts/nuts/check nuts and washers of galvanized steel, GI Strip encased in and including 40 mm bore GI light grade protection pipe starting from top edge of the earth platelaid in ground/floors fixed on wall. GI strip to be connected with LT Panel with provision of charcoal dust & common salt all around the earth plate 15 cm layersincludingnecessary excavation and earth work in any type of soil/strata, provision of concrete earth pit using PCC 1:3:6 type C-2 including RCC cover using PCC 1:2:4 type B1 20 mm dia GI light grade with wire mesh and tunel for watering arrangement, complete all as shown on electrical plate No. 3 of SSR Part I includig testing after completion of earth complete all as specified. |
| 147 | Supply and fixing / laying of GI pipe medium grade 50 mm dia including all fittings such as bend, tee, elbow, union, reducer, tee reducer etc laid or fixing/clamping on floor /surface / air/ wall, complete all as specified and directed. |
| 148 | Supply and fixing / laying of GI pipe medium grade 25 mm dia including all fittings such as bend, tee, elbow, union, reducer, tee reducer etc laid or fixing/clamping on floor /surface/air/wall, complete all as specified and directed.(Branch Connection from 50 mm GI to Prop Building OHT) |
| 149 | S & F Gun metal globe/ gate valve 50 mm bore with iron wheel head, screwed both ends for iron pipes, ISI marked, complete all as specified and directed. Note: Union or long screw have to provided before fixing of gate valve if required. |
| 150 | S & F Gunmetal globe/ gate valve 25 mm bore with iron wheel head, screwed both ends for iron pipes, ISI marked, conf to IS complete all as specified and directed. Note: Union or long screw have to provided before fixing of gate valve |
| 151 | M&L for construction of valve chamber of size 900 x 900 x 900 mm internal dimensions,3 mm thick MS sheet cover with 2 Nos MS hinges welded to angle iron frame of 40mm x 40mm x 5 mm thick with lifting hook and locking arrangement complete with necessary earth work 230 mm thick, brick work in CM (1:6), PCC bed (1:4:8) type D2 150 mm thick, cement plastering, finishing 15 mm thick in CM (1:4) and applying a coat of black bituminous paint to the steel surfaces completeall as specified and directed |
