Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | M&L for Relieving structural members such as coloumn, beam and slabs of their superimposed loads partially or fully by provision of adjustable steel props, frames etc. including providing necessory timber runners, bracing, jacking up arrangement all complete to the satisfaction of engineer-in-charge(Removing and redoing of brick work, if requied shall be measured andpaid seperately) |
| 2 | M&L for chipping, removing carefully concrete work by low impact hammer, breaker with out damaging the structure & cleaning and disposal of debris out side the premises etc,including errection of double steel scafolding, covering with green cloth and all the safety measures/precuations and remove the debrius outside MD land (as per the direction of BMC) complete all as specified and dircted.( hard concrete should not be removed by hammer) |
| 3 | M&L Clean existing reinforcement with wire brush/rotary wire brush to make surfce free from rust scales, loose material, dirt etc. complete and providing applying two coats of alkaline rust converting primer confirming to ASTMB-117, on the existing rebars and allowing it to react with rust for 6 hrs and form a corrosion resistant, insoluble and adherant protective layer, including cleaning the reinforcement, wirebrushing to remove loose rust spalls, with time interval of 1 hour between the coats. |
| 4 | M&L Replacement of steel reinforcement with TMT (CRS) bars of appropriate size where 20% of cross section is reduced including dismantling of rusted steel including application of rust convertor FEOVERT and applying protective coating IPNET-RB complete all as specified and directed, |
| 5 | M&L Providing and application of hightech concrete penetrating, water based, organic, Bi-polar, calcium nitrate free, migratory corrosion inhibitor on concrete surface having Ph9.5 which migrates to a virtual extent of 100 mm inside concrete through pores, to inhibit the corrosion process on embedded steel at both anodic and cathodic ends by depassivating the electro-chemical reaction in that region thereby protecting rebar on all sides. |
| 6 | M&L Providing and apllying structural grade EPIBOND-21-LP prior to application of any type of mortar plaster confirming to ASTM-C882-91(Arizona slant shear test) to ensure bound between old concrete and new concrete all as per manufactures instruction and as directed by Engineer-in-Charge. |
| 7 | M&L Building up the profile of structural member by using latex additives (MONOBOND) modified air cured mortar system (polymer modified mortar/LW+) (1:5:15=1 monobound-5 cement-15 sand) )-in damaged area in 30 mm thickness including levelling profilling etc. complete all as per manufactures instruction and as directed by Engineer-in- charge . |
| 8 | M&L Rebuilding the section of damaged RCC elements to desize size avarage thickness 50 mm by proving and casting with microconcrete of grade M-40 and above including all lifts, drilling holes, shear connectors, providing and fixing of water tight shuttering of minimum 12 mm thick with suppoerting frame work, all lead lift, mixing, placing , deshuttering, levelling the surface by grinding off cementitious slurry or construction joint diffrences if any to satisfaction of Eng-in_charge |
| 9 | M&L Opening the seperation cracks at the junction of RCC and masonary where ever directed andinstructed in to V grooves 2 inch to 3 inch from the eaither sides of the cracks by carefully marking the areas to be opened up using a cutting machine and skillfully/carefully chiselling with a well sharpened chisel and hammeras directed including wire brushing and washing of concrete substrata and masonry wall with water jet to the surface thus repaired to the entire satisfaction of Engineer -in-Charge as instructed and directed. |
| 10 | M&L Moistering the cracks providing and applying priming/ bonding coat of slurry made out of polyalk EP and cement (or equivalent as specified in the list of brand names) in proportion 1:1 to surfaces prepared as instructed and directed. Filling the cracks/ grooves by providing and applying Polyalk EP polymer modified cement mortar (or equivalant as specified in the list of brand names) in propotion of 1:5:15 (Polyalk EP : cement: graded sand /quarts sand) on the prepared surface and finishing it in level with the exsisting plaster including hand packing curing and making in the surface similar to the external plastering using wooden floats /punch etc complete as per specified and directed. |
| 11 | M&L Drilling holes of required size up to 16 mm diameter and up to 50 mm depth in concrete and cleaning the same as directed |
| 12 | M&L Providing and fixing 12 mm diameter aluminium/PVC injection nipples and securing the same as directed.& providing and injucting cementitious grout using CEBEX- 112 additive of Fosroc at the rate of 225 grams per bag of cement and using suitable mechanical gun / pump including mixing etc. complete all as specified. |
| 13 | M&L Carefully chiselling /chipping out all existing loose decayed plaster of external facades and terrace areas (in entire areas) using plaster brackingmachine and or well sharpend chisels & hammers at proper angles carting away the debris outside of bldg permises etc.complete as directed by the consultants, providing appying 20 /25 mm thick sand faced plaster concrete member brick work etc. External wall facades using approved screeneed and pre washed river sand including base coat of 13 to 15mm thick in CM 1:4 and curing the same for not less than three days and keeping the surface of base coat rough to recive the sand face treatment 6 to 8 mm thick of CM 1:3 finishing the surface by taking out gains and curing for 7 to 10 days providing and mixing approved water proofing compound in requied quantiity in both the coat complete all as specified. |
| 14 | M&L Chipping out all existing loose and decayed internal plaster and redoing the same with 15 mm thick cement plaster in CM 1:4 finishing with instant neeru of elephant brand or equivalent in the inside areas of staircase areas and over internal structural members of premises etc. |
| 15 | Removing and demolishing the existing water proofing treatment of any type up to slab level of any thickness stacking the excavated debris on the ground floor in the compound of the bldg carting away the same out side the MD land. |
| 16 | M&l for cement concrete Type B1 1:2:4 20 mm graded aggregate 40 mm thick in floor finishing the surfaces even and smooth with out using extra cement |
| 17 | M&L for water proofing treatment to RCC roof slab all as specified below and as directed:-( a) Apply one coat of bitumous primer @ 0.25 Kg/Sqm.(b) Apply a coat of blown type bitumen grade 85/25 heated to working temperature of 180 degree centigrade and applied at 1.20 Kg/Sqm of the surface area. (c) Laying APP polymer modified membrane 4mm thick with non woven polyster reinforcement weighing not less than 4.00 Kg/ Sqm applied by torch application method and inserting membrane on vertical surfaces upto 300 mm height in continuation with floor waterproofing. (d) Apply a coat of blown type bitumen grade 85/25 heated to working temperature of 180 degree centigrade and applied at 1.20 Kg/sqm of the surface area. (e) Apply a coat of solar reflective bituminous aluminium paint @ 0.10 Kg/Sqm. |
| 18 | M&L cleaning and repair the surface of APP membrane removal of debris, roof tilesaccumulated removal of algae,and preparing the surface by cleaning a high pressure water jet and ensure that it is free of dust, oil, grease loose particle vegitation root etc of any description and in position including removing of accumulated material outside MD land with all necessory arragements and for sealing opened overlaps and voids of existing APP membrane using thermo fusion using LPG torch inserting cement slurry with liquid water proofing compound @ 200 ml of Dr. fixit pidiproof LW per 50 Kg of cement water proofing compund on coving and on joints of APP membrane maualy to seal all joints, cracks and fixing roof tiles of exixting tilesby cement mortar and pointing te tiles and matching with the existing surfacecomplete all as specified and directed. |
| 19 | M&L Cement concrete tiles 30cm X30 Cm x (20-22) mm thick machine pressed set jointed in neat cement slurry in floors and cut and polished over 20 mm cement screed (1:4 ), complete all as specified and directed. |
| 20 | M&L Carefully chiselling /chipping out exixting cracked IPS and providing IPS fnish over chajja top staircase room top and OH/WT etc. Laying brick bats metal pieces to the desired thick ness and slope finished with cemnt mortar plasrter of specified and required thick in CM 1:4 with neat cement slurry including water proofing compound curing etc. including making junction wattas etc. complete as specified and directed. |
| 21 | Demolition of reinforced cement concrete of any description and in any position( reinforcement cut as required to facilitate demolition whenever required), complete all as specified and as directed. |
| 22 | Demolition of brick work or stone masonary built in cement mortarincluding all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles. |
| 23 | Material andlabour for brick work with sub class \"B\" bricks, straight or curved on plan exc 6 m mean radius, built in CM (1:6), complete all as specified. |
| 24 | M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius inhalf brick thick wallsbuilt in CM (1:4), complete all as specified. |
| 25 | Providing & applying weather proof paint exterior wall finish on newly plastered surfaces including surface preparation, applying suitable wall prime seal primer 8-10 sqm per ltr coverage area and application of two coats (base coat 4.2-4.7 & top coat 6-6.5 sqm per ltr coverage area ) & of paint by roller etc. complete all as specified and directed by the Engineer-in-charge. Notes:-1. The paint shall be used in top most quality of approved make . 1. Work will be executed by authorised applicator of approved manufacturer. 2. Every coat of finish will be approved by GE before starting new layer/coat.3. Contractor to submit minimum 05 yrs warranty certificate from the company. |
| 26 | Material and labour for preparation of new plastered surface of wall and applying 2 coats of oil emuslion distemper over a coat of primer on3 mm thick wall care putty (JK / Birla) all as specified and directed. |
| 27 | M&Lfor preparation of old plastered surface of wall and applying 2 coats of water based distemperall as specified and directed. |
| 28 | M&L Rendering 10mm thick on fair faces of ceiling in CM (1:3) & rendering is to be finishing even & smooth without using extra cement., complete all as specified. |
| 29 | Material and labour for preparation of new plastered surface of ceiling and applying two coats of oil emulsiondistemper , complete all as specified and directed. |
| 30 | M&Lfor preparation of old plastered surface of ceiling and applying 2 coats of oil emuslion distemper all as specified and directed. |
| 31 | M&L for preparation of old painted steel surfaces of any description, over 10 cm in width or girth not otherwise described and applying one coat of synthetic enamel paint with necessary scafolding for high rise bldgs etc all as specified and directed. |
| 32 | M&L for preparation of old painted wooden surfaes of any description over 10cm width or girth and applying one coat of synthetic enamel paint including external window with necessary scafolding for high rise bldgs. |
| 33 | M&L for preparation of old treated wooden surfaces of any description, over 10cm in width or girth and finishing with synthetic varnish complete all as specified |
| 34 | M&L for preparation of newly steel surfaces of any description over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 35 | M&L for preparation of newlywooden surfaes of any description over 10cm width or girth and applying two coats ofsynthetic enamel paint over a coat of pink primer incl preparation of surfaces. |
| 36 | Dismantling plain /corrugated steel sheeting of any size type in roof covering all as specified and directed. |
| 37 | M & L for pre-painted hot-dip aluminium-zinc alloy metallic coated plain steel sheet as per IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in ridge/ valley/ gutter fixed with self tapping screws as specified including necessary scaffolding and safety measures at any floor for height of building exceeding 10 metres but not exceeding 20 metres complete all as specified and as directed. |
| 38 | M & L for pre-painted hot-dip aluminium-zinc alloy metallic coated corrugated steel sheet, any pattern corresponding to IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in roof covering fixed with self tapping screws as specified including necessary scaffolding and safety measures at any floor for height of building exceeding 10 metres but not exceeding 20 metres complete all as specified and as directed. |
| 39 | Taking up or down 15mm bore steel tubing and connections, with or with out concealeed linecincluding cleaning for refixing,complete all as specified. |
| 40 | Taking up or down 20mm bore steel tubing and connections,with or with out concealeed line complete all as specified. |
| 41 | Taking up or down 25/32mm bore steel tubing and connections, with or with out concealeed line complete all as specified. |
| 42 | Taking up or down40/ 50mm bore steel tubing and connections,with or with out concealeed line complete all as specified. |
| 43 | S&F 15mm bore CPVC pipes of pressure rating 10 Kg/cm2 fixed complete to wall or ceilingor in floor etc,.where ever concealledwith all fitting open concealledcompleteall as specified. |
| 44 | S&F 20mm bore CPVC pipes of pressure rating 10 Kg/cm2 fixed complete to wall or ceilingor in floor etc. , where ever concealled with all fitting completeall as specified. |
| 45 | S&F 25mm bore CPVC pipes of pressure rating 10 Kg/cm2 fixed complete to wall or ceiling or in floor etc. , with all fitting and where ever concealledcompleteall as specified. |
| 46 | S&F 32 mm bore CPVC pipes of pressure rating 10 Kg/cm2 fixed complete to wall or ceiling in floor etc. , with all fittingopen or concealledcompleteall as specified. |
| 47 | S&F 50 mm bore CPVC pipes of pressure rating 10 Kg/cm2 fixed complete to wall or ceiling open concealled or in floor etc. , with all fitting and where ever concealledcompleteall as specified. |
| 48 | S&F as in repairs 15mm fancy type chromoum platedBib taps, Cat Part No.CQT-CHR-23037of Jaquar or Techno Commercia lequivalantinParryware or Hindwareas approvedcast copper alloy with crutch or butterfly handle, screwed down, fixed toiron pipe or for brass ferrule complete all as specified and directed. |
| 49 | S & F in repairs15 mm stop valve /angle valve fancy type CP Cat Part No.CQT-CHR-23053 of Jaquar or Techno Commercia lequivalantinParryware or Hindwareas approved chromium platedscrewed down, high presure with butterfly handle screwed both ends for pipeand fixed to pipe of15mm dia bore complete all as specified and as directed. |
| 50 | S&F in repair 15 mm boreconcealed Stop valves , CP, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions & fixed as in repairs. |
| 51 | S&F in repairs PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and as directed. |
| 52 | S&F in repairs PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and as directed. |
| 53 | S&F in repairs of vitreous china colouredwash down water closet pan (pedestal pattern),including plastic seat cover(excluding fixing bolts, flushing cistern and flush pipe) including connection to trap and drain (or outgoing pipe) and to flushing pipe, antisyphoage pipe etc complete all as specified. |
| 54 | S&F in repairs PVC valveless syphonic action type ,flushing cistern coloured Low level white, with inlet ball valve ,float and handle10 Ltr capacity including brackets. |
| 55 | S&F in repair wash hand basin vitreous china coloured(flat back) of size 550x400mm including bracketdia 32mm dia waste coupling and32mm dia PVC flexible waste pipe 90cm long etc. complete all as specified, |
| 56 | S&Fvitreous chinacounter top Wash Basin, coloured, oval type of size 560mm x 470mm x 190mm including cutting to granite slab for table coiunter,mirrorpolishing fixing in position , waste pipe, 32 mm waste coupling etc. Make: jaquar/Cera. Complete all as specified and directed by Engineer-in-charge. |
| 57 | Supply and fixing coloured vitreous china half stall urinal of approved make and design, including PVC connection of 600mm length with spreader and union, PVC connection from flushing line to spreader, CP brass spreader with check nut, outlet connection directly to waste pipe with all required fittings, complete with necessary brackets, nuts, bolts, rubber gaskets, washers and inlet pipework, including cutting and making good the wall and floor wherever required, all as apecified and directed |
| 58 | S&F vetrreous china coloured Urinal partition size 300X700 mm all as specified and directed. |
| 59 | S&F in repairs fancy type CP Pillar taps 15 mm dia, cast copperalloy, with capstan heads, screwed down high pressure, suitable for counter top/ bracket fix wash basin and with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified. |
| 60 | S&F repair 600mm x 450mm bevelled edge mirror of selected quality glass, mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plugs with CP Brass screws and cup washerscomplete all as specified and directed. |
| 61 | M&L for water proofing treatment of sunken slabs by cleaning RCC slab surface floors and walls by wire brush and rendering 6 mm thick in CM 1:4 mixed with integral WPC on uneven surface to make it even.Fill it water and check for dampness and seepage, all junctions points of side walls where CI/GI pipe are passing shall be sealed with epoxy mortar.Apply two coats of polymer modified cementious water proofing coating of minimum thickness of 1 mm each layer as per manufacturers instructions on floor & walls (upto 100 mm above FFL)and spray coarse sand on surface when the second layer is still sticky.Apply 20 mm thick plaster in CM 1:4 mixed with integral WPC of approved make on floors and walls including rounding of corners and junctions stoping towareds spouts.All pipes laid in sunken portions shall be covered with 50 mm thick PCC 1:3:6 all around after painting with anti corrosive black japan paint on GI/CI pipes.Test the water proofed area by filling water at least 72 hours and tested for leakage/seepagefor the entire satisfaction of GE.After above said treatment apply two coats of hot blown bitumen @ 1.5 Kg /Sqm for each coat and laying APP based polymeric membrane minimum weighing 3Kg/Sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150gms/Sqm) land on primed surfaces by forced applicationAPP based polymeric membranceand providing 40 mm cpvc pipe of 30 cm length for spotingin floors , tile work shall be carried out 2 to 3mm spacer filling with epoxy grouting complete all as specified and directed. (Note : If leakage/Seepage occured after filling water at least 72 hours, the above said treatment will be re-done completely) |
| 62 | M&L for cement concrete 1:7:12 type F2, (40 mm graded stone agg) as in foundation fillingand sunken floors etc all as specified and directed. |
| 63 | Supply & fixing in replacement vitreous China squatting pan \"Orissa\" pattern of size 580mm x 440mm white with integral foot rests including lime concrete for fixing the trap and making connection to trap and flush pipe and making good the floor to existing specifications completeall as specified and directed by Engineer-in-Charge. |
| 64 | S&F Aluminium hats and coat hooks single solid body 175 mm to 250 mm fixed to wall with SS crews all as specified and directed. |
| 65 | S&F Aluminium wardrobehooks single solid body 50 mm to 75 mm all as specified and directed. |
| 66 | S&F hasp and staple aluminium anodised 100mm all as specified and directed. |
| 67 | S&F GI wire with mild steeltigtening arrrage ment in each room for tying mosquito proofing net where ever necessory all as per specified and directed. |
| 68 | S&F in repairs Toilet paper holder with flat recessed type stainless steel Complete all as specified and directed. |
| 69 | S&F as in repairs brass chromium plated shower rose 100mm diaincluding 160mm long shower arm casted body round shape for wall mounted shower Cat Part No.OHS-CHR-1989 and Cat Part No.SHA-CHR-477 respectively of Jaquar or or Techno Commercia lequivalantinParryware or Hindwareas approved, including fixed to 15mm bore pipe, complete all as specified and directed. |
| 70 | S&F as in repairs Health faucet (ABS Body) Cat Part No. ALD-CHR-587of Jaquar or or Techno Commercia lequivalantinParryware or Hindwareas aprroved mild steel chromium plated suitable for 15 mm dia pipe with 1.00 metre long spirochrome Flexible tube and wall hook including making connections and fixed in position complete all as specified and directed. |
| 71 | S&F in repairs Stainless steel Towel rail 600 mm longCat Part No ACN-CHR-1181FSof Jaquar or of equivalent inParryware or Hindwareas approved including necessarybrackets complete all as specified and as directed. |
| 72 | S&F in repairs Stainless Steel Soap Dishas approved fancy type fixed with two Steel/ CP Screws complete all as specified and directed |
| 73 | S&F in repair decorative glass corner shelf round 10mm thick, 300mm size with stainless steel railing, fixed with D type stainless steel bracket on wall of approved design and pattern all as specified. |
| 74 | S&F in repair rotational moulded polythylene water storage tanktankof2000 litre capacityhoisted including 20 mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 210 grms ) and dismantling old tank all as specified in SSR Part I. complete all as specified and directed . |
| 75 | S&F in repair 1000 litre capacity rotational moulded polyethylene water storage tanks (cylindrical, vertical with closed top ) hoisted and fixed position all specified in SSR Part-I, with and including 15 mm dia ball valve, high pressure of PTMT, with epoxy coated aluminium rod & high density plastic ball, minimum weight 210gm, screwed for iron pipes and fixed; including disconnecting and dismantling/ taking down of existing old unserviceable water storage tank , complete all as specified and directed . |
| 76 | S&F polythylene water storage loft tank of500 litre capacityhoisted including 20 mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 210 grms ) and dismantling old tank all as specified in SSR Part I. |
| 77 | S&F as in repairs Gun-metal, globe or gate valves ISI marked50mm bore dia., with iron wheel head, screwed both ends for iron pipe and fixed above 5th floor terrace complete all as specified and directed. |
| 78 | S&F as in repairs 50mm dia ball brass valve, high pressure with polythene float and flynutscrewed for iron pipes all as specified and directed. |
| 79 | Material and labour for cement 1:2:4 type B-1 (12.5mm graded stone aggregate) as in roof kerbs and leveling course on RCC roof surfaces ( Terrace above 5th floor of bldg.) all as specified and directed. |
| 80 | Taking down chowkats or frames n exc 1.5 sqm each with shutters (without taking off shutters from the frame) , complete all as specified and directed. |
| 81 | Taking down chowkats or frames exc 1.5 sqm each but n.exc 4 sqm with shutters (without taking off shutters from the frame) all as specified and directed. |
| 82 | Taking down shutters of any descriptionnot exc 1 sqmeach all as specified and directed. |
| 83 | Taking down shutters of any description exc 1 sqm and n exc 2 sq.m each all as specified and directed. |
| 84 | S&F 2nd class hard wood (sal) plain, solid, straight chawkhats and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints all as specified. |
| 85 | S&F 32mm thick flush shutters, solid core construction, with block board core and ply wood face panels, commercial type on both side all as specified and directed. |
| 86 | S&F 30mm thick 2nd class hardwood glazed and skeleton shuttersopen rebated and prepared to receive glass, gauze, etc. divided in to squares,with plain, chamfered or rounded , mitred and rebatedsash bars,any numbers ; edges of framing plain, chamfered or rounded , fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, Section 8 clause8.24 (b) ; supplied and fitted to chowkhats of Second class hard wood. All as specified and directed. |
| 87 | M & L for 30mm thick 2nd class hard wood panelled shuttertwo pannel with lock rail and pannel of 9 mm ply or 12 mm veneered particle boardwith commercial veneer on both sideand fitted to chowkat all as specified and directed. |
| 88 | S&F Factory made single extruded WPC (WoodPolymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and directed. |
| 89 | M&L factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screwsand as per specification & drawing complete all as specified and directed. |
| 90 | S&F stainless steelwire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel stapple etc. all as specified and directed. |
| 91 | S&F 300 mm long aluminium alloy, sliding door bolt withhasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts all as specified and directed. |
| 92 | S&F for aluminiumanodized barrel tower bolts 200 mm of extruded section all as specified and directed. |
| 93 | S&F for aluminiumanodized barrel tower bolts 150 mm of extruded section all as specified and directed. |
| 94 | S&F 150 mm size aluminium alloy handles, febricated type extruded section, ISI markedall as specified. |
| 95 | S&F 125mm long SS Butt hinges, medium weight, cold rolled mild steel, all as specified and directed.. |
| 96 | S&F 100mm long SS Butt hinges, medium weight, cold rolled mild steel, all as specified and directed.. |
| 97 | M&L for PCC 1:3:6 type C-2 (40 mm graded stone aggregate) as in foundation, filling and mass concrete all as specified and directed. |
| 98 | M & L for MS flat for hold fast. Conforming to Fe-290-0 or Fe-165 all as specified and directed. |
| 99 | S&F in 140 mm long floor door stopper of aluminium door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring all as specified |
| 100 | S&F in repairs fancy type curtainrods, powder coated aluminium of 20-25mm size incl end brackets, hooks etcand fixing arrangements complete all as specified and directed. |
| 101 | S&F in repairs doorcloser aluminium (Die cast) body hydraulically regulated, designation No 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 Kg and fixed all as specified and directed. |
| 102 | Dismantling old rusted GI frame work of any description all as specified and directed |
| 103 | S&F of grid 605 x 605mm Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete all as specified and directed . |
| 104 | S&F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified |
| 105 | M&Lin repair for false ceiling made out of 600x600x 6mmthick( non asbestos fiber cement designer/coloured) ceiliing board / tiles deep panel as per sample. |
| 106 | S&F in repairs18/19 mm thick prelaminated partical board exterior grade prelaminated both side with lamination and other side balancing white lamination fixed with screw to frame work cupboard etc including 6 mm thick teak wood beading all around complete all as specified and directed. |
| 107 | S&F in repairs9 mm thick prelaminated partical board interior grade prelaminated both side with lamination and other side balancing white lamination fixed with screw to frame work cupboard etc including 6 mm thick teak wood beading all around complete all as specified and directed. |
| 108 | S&F in rapairs 12mm thick plywood, grade bwp type BB, fixed with screws to timber frame as in paneling/partition/ base for loft tanketc complete all as specified and as directed.. |
| 109 | M&L for wooden wall panelling made out of 15 mm thick I st class hard wood boarding, treated for termite proof planed one side and edge tongued and grooved width of panel exceeding 15 cm not exceeding 30 cm and fixed with brass screws, nails, glue beads jambs, joint filling, polishing, varnishing to uniform and finising the surface as per direction of Engineer in Chargeincluding aluminium frame work complete all as specified and directed. |
| 110 | M&L 0.9mm thick decorative texture finish laminate type 1, of surface finish colour and pattern as approved fixed with adhesive as per makers instruction complete all as specified and as directed. |
| 111 | S&F powder coated (colour of coating as directed) aluminium (minimum 25 micron thickness of coating) ofvarious section as required/suitable for doors, window & partition/Ventilator (sliding /or openable type)etc including fixing and making the frames hinges to receive glass/wire gauge etc.Complete incl all fittings like jointing cleats, glazing clips, rubber neoprene packing. anodised aluminium snap beading screws etc.rubber beading, clips locking arrangement, handle,silicon sealant all around windows etc all as specified and as directed. |
| 112 | S&F in repair aluminium grill with and including suitable aluminiumanodised frame F/H section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, as directed by Engr- in- charge. |
| 113 | S&F 4.8 mm thick sheet glass selected quality n exc 0.5Sqm in each pane,fixed to Aluminium windows. |
| 114 | S&F 6.3 mm thick glass sheet ordinary quality obscured on one side,exc 0.5 Sqm in each pane,fixed to Aluminium frameall as specified and directed. |
| 115 | S & F sheet glass of 4.8 mm thick selected quality in square and exceding 0.5 Sqm in each pane, complete all as specified. |
| 116 | S & F sheet glass of 4.8 mm thick selected quality, frosted from one side, and n exceding 0.5 Sqm in each pane, complete all as specified. |
| 117 | Providing and fixing roller Venetian cloth blinds of approved make and colour, including aluminium/steel roller tube, side brackets, operating chain mechanism, complete, fixed in position |
| 118 | S&F fibre glass reinforced transulant sheeting 3 mm thick fixed to MS frame with nut blt with washer all as specified and directed. |
| 119 | S&F 5 mm prelam PVC Sheet fixing on aluminium frame work for partition inclusive of rubber beeding ,solvent etc and fixing to site all as specified and directed. |
| 120 | S&F aluminium alloy wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminium wire staples all as specified and directed. |
| 121 | S&F 4 mm thick bakelite sheet with docorative choice laminated on both side complete all as specified and directed. |
| 122 | Dismantling floor hearth or wall tiling including cement mortar beddingremoving serviceble tiles to store and rubbish off the permises.complete all as specified & as directed. |
| 123 | M & L Non - skid Ceramic tiles colouredof approved make 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM (1:6), complete all as specified. |
| 124 | M&L, Glazed ceramic wall tiles coloured of approved size and make on vertical surface such as dado/skirting over cement mortar backing coat, set jointed in neat cement slurry and pointed in white or colouredcementincluding 15mm thick backing coat in CM 1:4 , complete all as specified. |
| 125 | M&L forlight shade coloured vitrifiedceramic tiles 9- 10 mm thick (square/rectangular) polished area of each tiles not exceeding 0.36 Sqm in floors etc set and jointed in neat cement slurry and pointing in white or coloured cement to match incl15 mm thick screed bed in CM 1:4including dismantling of old tiles, complete all as specified and directed. |
| 126 | M&L forlight shade coloured vitrifiedceramic tiles 9-10 mm thick (square/rectangular) polished area of each tiles not exceeding 0.36 Sqm as in skirting etc set and jointed in neat cement slurry and pointee in white or coloured cement to match incl10 mm thick back coat in CM 1:4including dismantling of old tiles, complete all as specified and directed. |
| 127 | M&L, for machine cut mirror polished kota stone slab flooring 22-25mm thick over cement screed bed in CM (1:4) 15mm thick, & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete all as specified and directed. |
| 128 | M&L, for machine cut mirror polishedkota stone slab flooring 22-25mm thickin riser / treads of steps in single piece, skirting, dado and pillar laid over cement screed and jointed withover cement screed bed in CM (1:4) 15mm thick, & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing and rounding the edges where as required complete all as specified and directed. |
| 129 | M&L for Plain cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate as in floor/ plinth protection orpaving 75 mm thick and finished even and smooth without using extra cement,as in plinth protection all as specified |
| 130 | M&L for forming construction joint 50mm deep x 10mm wide filled with sealing compound Grade \"A\"in plinth protection, complete all as specified. |
| 131 | Roughening old concrete surface of old concrete floor by picking, sweeping clean and washing down with water to rmove dust etc all as specified and directed. |
| 132 | M&L brushing neat cement slurry with 3.0 kg of cement per Sqm all as specified and directed. |
| 133 | M&L for 100mm thickPCC 1:2:4 type B2 Using 40 mm graded stone aggregate as in sub basecomplete all as specified and directed. |
| 134 | Material and labour for PCC (1:2:4) type B1, using 20mm graded stone aggregate as in coping, kerb stone pcc or similar places etccomplete all as specified and directed. |
| 135 | M&L for Machine pressed precast concrete interlocking paver block having glossy finish shape and size as approved by GEconfirming to IS 15658-2006 of 80mm thickness, M-40 Grade of with grey cement and pigments laid over and including 50 mm thick dry sand cushioning and voids filled with dry and surface compact, including compaction by means of surface vibrator and removing old paver blocks complete all as specified and directed. |
| 136 | M&L 18-20 mm thick mirror polished Granite (of any type) work as in steps, jambs, pillars, cooking platforms, working table and like over 15 mm thick screed bed or bedding layer in cement mortar (1:4), including pointing in white cement (1:2) using marble dust with admixture of pigment to match withshade of granite |
| 137 | Rounding to edges of stone slabs on edge, such as in steps, cooking platform and making grooves for lining and other similar work complete all as specified and directed. |
| 138 | Taking down rolling shutter of any type incl taking down accessories like shaft, top cover, guide channel after straightening/ rectify warped/buckled parts and replacing unserviceable components with new with and including cleaning/overhauling greasing etc including Re-fixing complete to walls/RCC members all as directed by the Engineer-in-Charge. (All new components/accessories will be measured and paid separately as supply only under relevant item of schedule) |
| 139 | Taking down aluminium window/ventilaots of any size with out taking of shutter from framewith accessories all as specified and directed |
| 140 | Dismantling stone slab /tiles of any description or thickness in floors laid and pointed in any mortar, complete all as specified and directed. |
| 141 | S&F as in repairs Steel rolling shutters 1.25mm thickness of laths, without ball bearing, as specified including top cover, anchoring rod, hasp and staple; erected in position as indicated, complete:gear operated type with bevel gear box and crankhandle including taking down old rolling shutter with all fittings, complete all as specified. |
| 142 | S& FCollapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete |
| 143 | Supply and fixingMS suspension shaft of dia 50 mm incl springssuitable for rolling shutter, complete all as specified |
| 144 | Supply & fixing guide channel of width 65 mm wide & 25 mm deep and 3.15mm thick all as specified and as directed . |
| 145 | Supply and fixing in repair ball bearing for 40 to 50mm dia shaft of rolling shutter upto 6.0m widthall as specified and as directed.. |
| 146 | Supply and fixing in repairgear box and crank handle, all as specified and directed. |
| 147 | M&L for plain,black mild steel sheeting in gates, 1.25mm thick sheet welded or shouldered to angle iron frame and all as specified and directed. |
| 148 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/ dense soil. |
| 149 | Dismantling of 200mm reinforced concrete drain pipes, jointed in cement mortar, complete all as specified. |
| 150 | S&F for 200mm bore RCC pipe class NP-2 laid and jointed complete with collers as specified including testing all as specified and directed . |
| 151 | M&L for cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregate) as in bed to drain pipes including forming cradle after they are laid and tested for 200mm bore RCC pipe complete all as specified and as directed . |
| 152 | M&L for PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) as in foundations, filling ad mass concrete all as specified and directed.. |
| 153 | Taking down soil, rain water pipes (any size or pattern), including all fittings, heads,shoes,bends, swan-neck, etc. Including cleaning or refixing or removal to store ( measured over all as fixed along the center line over fittings and accessories) |
| 154 | Supply and fix 160 mm dia PVC (SWR) grade pipes, single socketed in any length with rubber ring joints fixed to walls / laid in trenches with and including and including fixing of pipes in wall with clamps as mentioned and shown in HQ CE (N) Mumbai zone TD Drg No TD/2023/01 toTD/2023/03 complete all as specified and directed. |
| 155 | Supply and fix in repairs 160 mm dia bore PVC (SWR) bends any radius |
| 156 | Dismantling of 100mm cast iron or reinforced concrete drain pipes, jointed in cement mortar, complete all as specified. |
| 157 | Dismantling of 75mm cast iron or reinforced concrete drain pipes, jointed in cement mortar, complete all as specified. |
| 158 | S&F 100 mm bore of sand cast CI soil waste pipe in any length with ears and jointed with neat cement paste fixed to wall and including fixing of pipes in wall with clamps complete all as specified. |
| 159 | S&F 75mm bore of sand cast CI soil waste pipe in any length with ears and jointed with neat cement paste fixed to wall and including fixing of pipes in wall with clamps a complete all as specified. |
| 160 | S&F in repairs 100 mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured),& ht. upto 4th floor of bldg., complete all as specified. |
| 161 | S&F in repairs 75 mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured)& ht. upto 4th floor of bldg., complete all as specified. |
| 162 | S&F 75mm sand cast CI Branch pieces (Tee), Single (equal), ordinary or inverted (spigot or socket type) or with parallel branches with ovel access door and jointed with neat cement paste to CI pipes fixed to wall or roof at any floor/ any height/ any location including all fittings complete all as specified and as directed by Engr-in-Charge. |
| 163 | S&F 100mm sand cast CI Branch pieces (Tee or Y), Single (equal), ordinary or inverted (spigot or socket type) or with parallel branches with ovel access door and jointed with neat cement paste to CI pipes fixed to wall, complete all as specified. |
| 164 | S&F 75mm sand cast CI Branch pieces (Tee), Double (equal), ordinary or inverted (spigot or socket type) or with parallel branches with ovel access door and jointed with neat cement paste to CI pipes fixed to wall or roof at any floor/ any height/ any location including all fittings complete all as specified and as directed. |
| 165 | S&F 100mm sand cast CI Branch pieces (Tee), Double (equal), ordinary or inverted (spigot or socket type) or with parallel branches with ovel access door and jointed with neat cement paste to CI pipes fixed to wall , complete all as specified. |
| 166 | S&F in repair cast iron cowl suitable for 75mm dia pipe , complete all as specified. |
| 167 | S&F in repair cast iron cowl suitable for 100mm dia pipe, complete all as specified. |
| 168 | M&L in repairs 75mm dia Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), complete all as specified. |
| 169 | S& F in repair PTMT grating 125 mm complete all as specified and directed |
| 170 | Cutting into existing manholes for connecting new drain making good to200mmpipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 Sec) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as reqd for 200mm bore of pipe. |
| 171 | Removal of excavated soils from site to distance exc1.50 Km but not exc 5 Km and depositing where directed , complete all as specified. |
| 172 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. in Hard / dense soil, complete all as specified. |
| 173 | M&L forMild steelTMT(CRS) bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, all as specified and directed. |
| 174 | M&L forMild steel TMT (CRS)bars 5mm dia and over upto and including 10mm dia in stirrups, spacers, binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips,all as specified and directed. |
| 175 | M&L providing and injecting chemical emulsion for post construction anti termite treatment along the external wall below concrete or masonary apron using chemical emulsion at 2.25 litre per linear meter including drilling and plugging holes etc with white cement and match the surface to existing apron complete all as specified and as directed. |
| 176 | M&L for post construction treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same all as specified and directed. |
| 177 | S&F in repairs ready made pully operated clothes drying system incl of four aluminium pipes of 2.70RM long each (4 pipe set), outer dia 22mm and inner dia 19.8mm channel assembly, locking system ropes and all fixing materials complete all as specified and directed. |
| 178 | Dismantling structural steel work of any description and in any position all as specified and directed. |
| 179 | Material & labour for stainless steel railing of grade 304 of specified section embedded into wall /floor including cutting weldingpolishing, as specified and directed . |
| 180 | S&FRolled mild steel in Roof truss (framed), trussed, purlins, rafter, crane gantries, rails and fastening and heavey bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe-410 (gde E-265) complete all as specified and directed. |
| 181 | S&F Rolled mild steel in Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc, as in vertical post and fixing of post with drilling and fixing with fastener of required size conforming to Fe-410 (gde E-250) complete all as specified and directed. |
| 182 | S&F Rolled mild steel in Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachmentconforming to Fe-410 (gde E-250) complete all as specified and directed. |
| 183 | S&F Rolled mild steel in wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes,notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work roof including securing bolts;conforming to Fe-410 (gde E-265) complete all as specified and directed. |
| 184 | Removing any kind of debris including loading in 5-7 Cum truck and conveying day to day basis to approved dumping point ie. @ urban/industry loading spreading etc. complete with all leads and lifts(lead 50 Km) |
| 185 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators,sockets,light fitting etc. removing materials to store for keeping in safecustody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc all as specified and directed. |
| 186 | M & L for concealed Point wiring complete with 1.5 sqmm single core multistranded FRLS PVC insulated unsheathed copper conductors 1100 volts grade drawn through & including PVC non-metallic double locked casing ISI marked with accessories fixed in wall/ceiling/truss including cutting chases, pinning in etc with PVC non metallic ISI marked terminal boxes concealedwall including one FRLS PVC insulated & unsheathed multistranded green colour copper conductor 1.5 sqmm as earth continuity conductor connected to common earth as earth dolly complete all as specifed and directed. |
| 187 | (a) One light point controlled by one switch SP one way. |
| 188 | (b) One ceiling fan point controlled with one 5A switch. |
| 189 | (c) One exhaust fan point controlled with one 5A switch. |
| 190 | (d) One 3 pin socket outlet 5Amps on independant board. |
| 191 | (e)One 3 pin socket outlet 5Amps on same board with other switches. |
| 192 | Material and Labourforconcealed point wiring for 15 Amps socketcomplete with 2.5 sqmm single core multistranded FRLS PVC insulated unsheathed copper conductors 1100 volts grade drawn through and including PVC non-metallic double locked casing and capingincludingPVC bend,teejointsetc as per site requirement, ISI marked with accessories fixed on wall/ceiling/truss etc with PVC non metallic ISI marked including one FRLS PVC insulated & unsheathed multistranded green colour copper conductor 4 sqmm as earth continuity conductor connected to common earth as earth dolly complete all as specifed and directed. |
| 193 | S&F Modular Switch , 6Amp, One way, 1 module, ISI marked complete all as specified and directed. |
| 194 | S&FModular Switch , 16Amp, One way, 1 module, ISI markedcomplete all as specified and directed. |
| 195 | S&F Modular Socket , 6 Amps, 2/3 pin combined2 module, ISI marked complete all as specified and directed. |
| 196 | S&F ModularSocket , 16Amps, 6 pin combined 2 module, ISI marked complete all as specified and directed. |
| 197 | S&F ceiling rose surface bakelite with ISI mark,three terminals complete all as specified anddirected. |
| 198 | S&FModular white cover plate with Frame 3 Module, ISI marked complete all as specified anddirected. |
| 199 | S&FModular white cover plate with Frame 4 Module, ISI marked complete all as specified anddirected. |
| 200 | S&FModular white cover plate with Frame 6 Module, ISI marked complete all as specified anddirected. |
| 201 | S&FModular white cover plate with Frame 8 Module, ISI marked complete all as specified anddirected. |
| 202 | S&FModular white cover plate with Frame 12 Module, ISI marked complete all as specified anddirected. |
| 203 | S&F Modular metal flush box 3module, ISI marked and including cutting hole in wall / ceiling/piller etcand making good surface complete all as specified anddirected. |
| 204 | S&F Modular metal flush box4 module, ISI marked andincluding cutting hole in wall / ceiling/piller etcand making good surface complete all as specified anddirected. |
| 205 | S&F Modular metal flush box6module, ISI marked and including cutting hole in wall / ceiling/piller etcand making good surface complete all as specified anddirected. |
| 206 | S&F Modular metal flush box8module , ISI markedandincluding cutting hole in wall / ceiling/piller etcand making good surface complete all as specified anddirected. |
| 207 | S&F Modular metal flush box 12 module, ISI marked and including cutting hole in wall / ceiling/piller etcand making good surface complete all as specified anddirected. |
| 208 | Supply and fixing integrated LED batten 20 Watt,(Min 130 Luman/watt)4 feet long, full white in Engineering plastic battern with white acrylic cover with built in electronic driver, pre-wired and connecting up with twisted twin core flexible copper wire of 0.5 sqmm from ceiling rose to connector of fitting including taking down existing unserviceable light fitting of any description complete all as specified and directed. |
| 209 | Supply and fixing serene 2\"x2\" 36 Watt luminare recess mounting, CRCA housing, white powder coated, with polymer diffuser complete with accessories including taking down existing unserviceable light fitting of any description complete all as specified and directed. |
| 210 | Supply and fixing integrated LED batten 10 Watt, ,(Min 130 Luman/watt) 2 feet long, full white in Engineering plastic battern with white acrylic cover with built in electronic driver, pre-wired and connecting up with twisted twin core flexible copper wire of 0.5 sqmm from ceiling rose to connector of fitting including taking down existing unserviceable light fitting of any description complete all as specified and directed. |
| 211 | S&F of New LED Bldg security light 45 Watt indus series powder coated pressure die cast aluminium high power LED bldg security lightwith heat resistant toughned glass with lens with IP66 Protectionincluding40 mm dia pipe bracket fixing on wall at any height with 02 nos of MS clamp of suitable size,complete all as specified and directed. |
| 212 | S&F MCB DB TPN 4 way suitable for three phase single, 415 volt sheet steel powder painted enclosure double door type with minimum IP-43 degree of protection withbuilt in 200 Amps copper bus bar, neutral link and earth link complete including flush off in wall with cutting and making good the disturbed surface including connection of circuits with copper pin terminals complete all as specified and directed. |
| 213 | S&F MCB DB SPN 12 way suitable for single phase AC supply, 230 V sheet steel powder painted enclosure double door type with minimum IP-43 degree of protection withbuilt in 200 Amps copper bus bar, neutral link and earth link complete including flush off in wall with cutting and making good the disturbed surface including connection of circuits with copper pin terminals complete all as specified and directed. |
| 214 | S&F MCB DB SPN 8 way suitable for single phase AC supply, 230 V sheet steel powder painted enclosure double door type with minimum IP-43 degree of protection withbuilt in 200 Amps copper bus bar, neutral link and earth link complete including flush off in wall with cutting and making good the disturbed surface including connection of circuits with copper pin terminals complete all as specified and directed. |
| 215 | S & F MCB TPN 40 to 100 Amps, 415 volt, 10 KA rating complete all as specified anddirected. |
| 216 | S & F MCB SPN 63 Amps, 240 Volts, C Series complete all as specified and directed. |
| 217 | S & F MCB SP 6-32 Amps, 240 Volts, C Series complete all as specified and directed. |
| 218 | Taking down old unserviceable submain cable of any size and capacity and finishing wall surfaces complete all as specified and directed. |
| 219 | Supply and fixsubmain wiring 4 run x 10 sqmm + 1 run x 10 sqmm earh wire FRLS unsheathed 1100 volts grade cable with stranded copper conductor of size 10 Sqmm in and including PVC casingcaping/ PVC conduit of suitable dia, ISI marked including 1 single core cable with stranded copper conductor of size 10 sqmm(green colour) for earthing.Note :- (i) Four runs of 10 Sqmm cable, 1 run of PVC casing & caping/ PVC conduit and 1 run of 10 Sqmm cable for earth shall be measured as 1 RM. |
| 220 | Supply and fixing submain wiring with proper colour coding,2 single core FRLS 1100 volts grade cable with stranded copper conductor of size 4 Sqmm in and including PVC Conduit/PVC casing caping of suitable size not less than 25 mm , ISI marked including 1 single core cable with stranded copper conductor of size 4 Sqmm(green colour) for earthing. Note : (i) 2 runs of 4 Sqmm cable, 1 run of PVC Conduit/PVC casing caping and 1 run of 4 Sqmm cable for earth wire shall be measured as 1 Run. (ii) Each Submain Wiring shall run in Seperate PVC Conduit/PVC casing caping. |
| 221 | Supply and fixing submain wiring with proper colour coding,2 single core FRLS 1100 volts grade cable with stranded copper conductor of size 6 Sqmm in and including PVC conduit/ PVC casing caping of suitable size not less than 25 mm , ISI marked fixed on wall/ceiling/ shaft of building with clamps at suitable intervals including 1 single core cable with stranded copper conductor of size 6 Sqmm(green colour) for earthing. Note : (i) 2 runs of 6 Sqmm cable, 1 run of PVC conduit/PVC Casing Caping and 1 run of 6 Sqmm cable for earth wire shall be measured as 1 Run. (ii) Submain Wiring for Each DB shall run in Seperate PVC Conduit/PVC casing caping. |
| 222 | Supply and fixing submain wiring with proper colour coding,2 single core FRLS 1100 volts grade cable with stranded copper conductor of size 10 Sqmm in and including PVC Conduit/PVC casing caping of suitable size not less than 25 mm , ISI marked fixed on wall/ceiling/ shaft of building with clamps at suitable intervals including 1 single core cable with stranded copper conductor of size 10 Sqmm(green colour) for earthing. Note : (i) 2 runs of 10 Sqmm cable, 1 run of PVC Conduit/PVC casing caping and 1 run of 10 Sqmm cable for earth wire shall be measured as 1 Run. (ii) Submain Wiring for Each Qtr shall run in Seperate PVC Conduit/PVC casing caping. |
| 223 | S&Fin replacementPlug and Socket enclosure, in sheet metal enclosure with MCB, SP 20 Amps 240 Volts complete with metal clad socketincluding flush off in wall with cutting and making good the disturbed surface for window typeair conditioners/geyser complete all as specified and directed. |
| 224 | Taking down ceiling fan of any size and make from each flat/room/at any location and keep in safe custody/ store after dismantling of fan blades and refixing the same in each flat at directed location after completion of civil work by following overhauling of ceiling fan, replacement of all unserviceable parts, providing safety wire, properly cleaning , removing old existing grease oil and applying new oil grease, varnishing of winding, cleaning dust rust, replacement of canopy, bushes, bearing with new including painting of complete fan synthetic enamel paint and assembling and connecting complete with copper conductor multi stranded 3 core wire of size 14/0.0076 complete all as specified and directed. |
| 225 | Taking down ceiling fan of any size and make from each flat/room/at any location and deposited in MES store after dismantling the blade to keep is safe custoday complete all as specified and directed by Engr in Charge. |
| 226 | Taking down exhaust fan of size 200 mm to 400 mm and make from each flat/room/at any location and keep in sage custody/ store after dismantling of fan blades and refixing the same in each flat at directed location after completion of civil work by following overhauling of exhaust fan, replacement of all unserviceable parts, louver, properly cleaning , removing old existing grease oil and applying new oil grease, varnishing of winding, cleaning dust rust, replacement of burnt motor, bushes, bearing with new including painting of complete fan synthetic enamel paint and assembling and connecting complete with copper conductor multi stranded 3 core wire of size 14/0.0076 complete all as specified and directed. |
| 227 | Supply and fixing ceiling fans complete with aluminum blades, down rods with safetyGIwire connecting up to fan hook,electronicregulatormodular type and accessories , 230 volts, 1200 sweep.Minair delivery 245 CFM with service value 8.75 CMM/W with brushles diret currentmotor 28 W, minimum rated speed 350 RPM, No of speed -5, insulation resistance above 2 mega ohm, No of blade - 03 Nos, TDH below 10%, class B insulation, starting voltage 120 V maximum BIS certified andconnecting up including provision of flexible 3 corecopper cable complete all as specified and directed. |
| 228 | Taking down ols unsv panel and Supply, fix, install, testing and commissioning ofindoor typeLT panel cubical shape,three phase, 4 wire, copper bus barrating 600 amps for phases and 400 amps for neutral made out of CRCA sheet ,2 mm thick ,factory fabricated , CPRI approved , powder coated ,dust and vermin proof , provn for ventilation , angle iron frameand four legs of 50x50x6mm thick angle iron ,1 ft long grouted on PCC foundation of height not less than 30 cm from the ground level , grouting properly ,and of suitable size to accommodate the items mentioned belowand having separate compartment /chambers for cable gallery busbar,switch gearand front side doubledoor openable , back side fixedwall etc all as specified and comprising of following including necessary cable connections to the MCCBs ,voltmeter,Ammeter and cable lugs etc . (i) MCCB 4 Pole, 415V, adjustable type, 400 Amps with breaking capacity 25KA Make- Schneider/Havells/Legrand-01 No (Incoming)(ii) MCCB 4 pole 415V fixed type, 63 to 100 Amps with breaking capacity 16KA. -08 Nos (out going)(iii)TPN 40 Amps- 12 Nos (outgoing)(iv) Voltmeter,digital type 0- 400 volt,with selector switch -01 set(v) Phase indicating lamps LED type ( red , yellow, blue) -01 set(vi)Ammeter Digital type 0-100Amps, with selector switch and CT\"-1set . |
| 229 | Material & Labour for Earthing with galvanised steel earth plate electrode 60 x 60 cm x 6 mm thick, burried directely in ground (earth pit not less than 2.5 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to galvanised iron strip 32 x 6 mm with the help of bolts, nuts, check nuts and washers of galvanised iron or steel, protection GI pipe of 40 mm dia including necessary excavation, PCC 1:3:6 type D2 and PCC cover 1:2:4 type B1 watering arrangement with GI pipe funnel, jali,and cast iron coverfixed on topof pit complete all as specified and shown in electrical plate No.3 including connection to the earthing test point andtesting on completion. |
| 230 | Excavation in trenches not exc 1.5 mtr wide & not exc 1.5 mtr in depth: for foundationetc or for manholes, laying of pipe in any type of soil and getting out complete all as specified |
| 231 | Returning filling in, including spreading, leveling watering & well rammng in layers not exc 25cm thick complete all as specified and directed by EIC |
| 232 | Removing excavated material to a distance not exc 50 mtr & depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified & diected |
| 233 | Supply andlaying, commisssionXLPE insulated armoured LT cable, 110 Volts grade with aluminium conductor of size 150 sqmm 3.5 laid in trenches/ through pipe/ ducts or fixed on wall etc complete all as specified and directed. |
| 234 | Supply andlaying, commisssionXLPE insulated armoured LT cable, 110 Volts grade with aluminium conductor of size 3.5core50 Sqmm laid in trenches/ through pipe/ ducts or fixed on wall etc complete all as specified and directed. |
| 235 | Supply andlaying, commisssionXLPE insulated armoured LT cable, 110 Volts grade with aluminium conductor of size 4core16 Sqmm laid in trenches/ through pipe/ ducts or fixed on wall etc complete all as specified and directed. |
| 236 | S&F HDPE of Pressure rating 6kg/cm sq pipe of 90 mm dia including necessary bends,elbows,Tees etc on cable protection complete all as directed. |
| 237 | M&L for cutting of Road/hardstanding not less than 30 cm in depth and 30 cm in width underneath the road for passing the cable/pipe and making good with PCC 1:2:4 type B-1whete road cutting done to make the road surface fair and level complete all as specified and directed by Engr-in Charge. |
| 238 | Note for all items above1)The tenderer shall note that before quoting his unit rates, all items of work shall be executed in a high-rise building (G + 3 floors) and shall include provision of necessary scaffolding and safety measures.2)Debris shall be removed from time to time as directed by the Engineer-in-Charge.3)Protective Work: Provision of temporary barricading using galvalume sheets around the periphery of the site up to a height of 5 m, complete all as specified and directed by the Engineer-in-Charge. |
| 239 | 4) The contractor shall be construct 05 Nos new temporary shed of (structural steel & Galvalume sheet)approx size 05M X10 M for storage of materials in the space provided by the user.. 5) Demolition of RCC structure shall be under controled demolition and any damage caused to the RCC structure or adjoining portions during demolition or dismantling, due to negligence of the contractor, shall be made good by the contractor at his own expense.6)Safety Precaution: Necessary safety precautions for men, material and structures shall be taken by the contractor during execution of work.6)Necessary steel scaffolding shall be provided by the contractor for multistoried buildings. The contractor shall ensure that all workmen wear safety belts at all times.7)The work shall be carried out while the building remains partially occupied.8)The quoted rate for all items shall be deemed to include compliance with all the above conditions. |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
