Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | SCH \"A\" PART-I (B/R WORK)Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as per specified and as directed by Engineer-in-charge. |
| 2 | Demolition of unreinforced cement concrete in ground floors and pavings nexc 15 cm thickness (below or above ground level) complete all as specified and as directed by Engineer-in-charge. |
| 3 | Demolition of stone slabs and tiles laid, bedded and pointed in any mortar of any description or thickness in floors, approaches, dado/Partitionsetc, complete all as per specified and as directed by Engineer-in-charge. |
| 4 | Demolition of unreinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed by Engineer-in-charge. |
| 5 | Dismantling framed work timber in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section, complete all as per specified and as directed by Engineer-in-charge. |
| 6 | Dismantling wall and ceiling boards (fibre, pulp, insulation, etc) or insulation board/Slabs/blankets of any thickness including cover fillets, complete all as per specified and as directed by Engineer-in-charge. |
| 7 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises , complete all as per specified and as directed by Engineer-in-charge. |
| 8 | Taking down cement plaster on brick wall of any description, including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed by Engineer-in-charge. |
| 9 | Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as per specified and as directed by Engineer-in-charge. |
| 10 | Dismantling wrought iron or mild steel work of any description not otherwise providedcomplete all as specified and as directed by Engineer-in-charge. |
| 11 | Dismantling water tanks of capacity exc. 500 and not exc. 1000 ltrs, complete all as per specified and as directed by Engineer-in-charge. |
| 12 | Taking down chowkat or frame with shutters (without taking off shutters from the frame) not exceeding 1.5 Sqm each and removing from site, complete all as specified and as directed by Engineer-in-charge. |
| 13 | Taking down chowkat or frame with shutters (without taking off shutters from the frame) exceeding 1.5 Sqm but not exceeding 4 Sqm each and removing from site, complete all as per specified and as directed by Engineer-in-charge.(Note for Item No. 12.00 & 13.00 - Rate shall be deemed to be include for cuttingholes/demolition of masionry walls etc for taking down chowkats and making good the damaged surfaces). |
| 14 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as per specified and as directed by Engineer-in-charge. |
| 15 | Taking up or down 15 mm steel tubing and connections, including removing from site complete all as per specified and as directed by Engineer-in-charge. |
| 16 | Taking up or down 20 mm steel tubing and connections, including removing from site complete all as per specified and as directed by Engineer-in-charge. |
| 17 | Excavation in trenches n.exc 1.5m wide and n.exc 1.5 m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes etc n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in soft/loose soil complete all as specified and as directed by Engineer-in-charge. |
| 18 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm in hard/dense soil, complete all as per specified and as directed by Engineer-in-charge. |
| 19 | Removing excavated soil material not exc. 50 m & depositing where directed at a level not exc. 1.5 m above starting point complete all as specified and as directed by Engineer-in-charge. |
| 20 | M&L for PCC 1:3:6 Type C2 (using 40mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as specified and as directed by Engineer-in-charge. |
| 21 | M&L for PCC (1:2:4) type B-1 ( using 20 mm grade crushed stone aggregate) as in water tank platforms, filling and mass concrete, complete all as per specified and as directed by Engineer-in-charge. |
| 22 | M&L for plain cement concrete type C-2, 1:3:6 (using 40 mm gradedstone aggregate) as in surface channels and drains, complete all as per specified and as directed by Engineer-in-charge. |
| 23 | M&L for PCC (1:2:4) type B1 (using 20 mm graded crushed stone aggregate) as in in copping, bed plates etc of main holes, roof kerbs or mud stops, rounded or chamfered on edges include necessary formwork (straight or curved), complete all as specified and as directed by Engineer-in-charge. |
| 24 | M&L for precast cement concrete PCC 1:2:4 type B0 (using 12.5 mm graded Aggregate) as in blocks, louvres and jallies, 25mm thick (measured solid), including all mouldings and similar articles with plain faces set in cement mortar 1:4, complete all as specified and as directed by Engineer-in-charge. |
| 25 | M&L forRCC1:1.5:3, type A-1 (Nominal Mix), (using 20 mm graded crushed stone aggregate) as in foundations, including rafts, footings, foundation beams, plinth beams; bases for columns, mass concrete etc, complete all as per specified and as directed by Engineer-in-charge.Note: Reinforcement and formwork shall be measured and paid separately |
| 26 | M&L for RCC1:1.5:3, type A-1 (Nominal Mix), (using 20 mm graded crushed stone aggregate)as in chajjas,facia and like, complete all as per specified and as directed by Engineer-in-charge. |
| 27 | M&L for providing plain cementconcrete type C-1, 1:3:6, (using 20 mm graded stone aggregate), as in copings, bed block for filing hollow space of steel chowkhats, fixing of hold fast, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work, complete all as per specified and as directed by Engineer-in-charge. |
| 28 | M&L for precast cement concrete (1:2:4) type B1 (using 20 mm graded crushed stone aggregate) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces set in cement mortar 1:4, complete all as per specified and as directed by Engineer-in-charge. |
| 29 | Supply only Liquid water proofing compound confirming to IS , complete all as per specified and as directed by Engineer-in-charge. |
| 30 | M&L for fly ash brick work, straight or curved on plan to any radius in half brick thick walls built in cement mortar (1:4) complete all as specified and as directed by Engineer-in-charge. |
| 31 | M&L for fly ash brick work, straight or curved on plan exc. 6m mean radius in cement mortar 1:6, complete all as per specified and as directed by Engineer-in-charge. |
| 32 | M&L for cutting holes in brick walls inbrick walls Exc. half brick but not exc. brickbuilt in cement mortar or cement lime mortar and stone walls built in lime mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 , complete all as per specified and as directed by Engineer-in-charge. |
| 33 | Providingformwork to sides of concrete foundation, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter rough finished surface of concrete flat complete all as per specified and as directed by Engineer-in-charge. |
| 34 | Providing formwork to chullah hoods, chajjas, weather shades, corbels, water troughs and similar items including edges, rough finished surfaces of concrete flat etc., complete all as per specified and as directed by Engineer-in-charge. |
| 35 | S&F Pressed steel frames of size 125x60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete all as per specified and as directed by Engineer-in-charge. |
| 36 | S&F of30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as per specified and as directed by Engineer-in-charge. |
| 37 | Supply and fixing of factory made partly glazed i.e. upper panel will be wire mesh fitted externally in the clear space & lower panel will be plain colour PVC sheet 5mm thick PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail,; Panelling of plain colour PVC sheet to be fitted in the M.S.frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as per specified and as directed by Engineer-in-charge. |
| 38 | S&F of providing and fixing factory made uPVG white colour Sliding window (Area exceeding 2.00 sqm each) Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 no\"s, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories, including taking old unserviceable steel window, complete all as per specified and as directed by Engineer-in-charge.(Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured lor payment purpose.) |
| 39 | S&F of Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as per specified and as directed by Engineer-in-charge. |
| 40 | Supply and fixing of factory made solid panel factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as per specified and as directed by Engineer-in-charge. |
| 41 | S&F of Powder coated aluminium louvered ventilators of size n exc 0.50 Sqm area with glass louvers, without sash bars of aluminium sections weighing not less than 0.605kg/m for frame of size 40x20x2mm including necessary jointing cleats, glazingcleats, rubber packing , anodised aluminium snap beading, screws, anodised aluminium fittings and 5.5mm thick tinted glass fixed in panels with suitable locking arrangementsincluding taking down of old existing steel ventilator and making good disturbed surfacesof wall complete all as per specified and as directed by Engineer-in-charge. |
| 42 | S&F 150 mm long aluminium, anodised, barrel tower bolts of extruded section, complete all as per specified and as directed by Engineer-in-charge. |
| 43 | S&F of 100 mm butt hinges, medium weight, cold rolled mild steel and fixed , complete all as per specified and as directed by Engineer-in-charge. |
| 44 | S&F of 200 mm long aluminium, anodised, barrel tower bolts of extruded section, complete all as per specified and as directed by Engineer-in-charge. |
| 45 | S&F of 125 mm long aluminium handles, cast type, anodised, complete all as per specified and as directed by Engineer-in-charge. |
| 46 | S&F of 150 mm long aluminium handles, cast type, anodised, complete all asspecified and as directed by Engineer-in-charge. |
| 47 | S&F of 300 mm long mild aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed by Engineer-in-charge. |
| 48 | S&F in repair of harrison rails curtain rod, anodised aluminium alloy with fixing brackets, stops, rollers etc. complete all as per specified and as directed by Engineer-in-charge. |
| 49 | S&F of floor door stopper with overall length of cover plate 140 mm long of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor, complete all as per specified and as directed by Engineer-in-charge. |
| 50 | S & F Stainless steel wire cloth, 0.36 mm dia of wire and average width of aperture 1.40 mm and fixed with tinned stacks, or galvanized wire staples complete all as per specified and as directed by Engineer-in-charge. |
| 51 | S&F in repair of brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges, complete all as per specified and as directed by Engineer-in-charge. |
| 52 | M&L for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all asspecified and as directed by Engineer-in-charge. |
| 53 | S&F of screw bolts (machine made) (diameter of neck 16 to 20 mm) with hexagonal or square head at one end and screwed the other or screwed both ends to be fitted with washers and one hexagonal or square nut exc. 22.5 cm but n.exc. 30 cm long MS Work as in bands , straps, supports or stays incl bolts, if reqd. , hold fasts, wall ties and similar small articlesconforming to Fe-290 Gde E-165 complete all as specified and as directed by Engineer-in-charge. |
| 54 | S&F of roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. Confirming to Fe 410-W (Gde E- 250) quality-A, includingsteel is painted one shop coat of zinc chromate primer paint (including preparation of surface) at Contractor’s workshop before fabrication, complete all as per specified and as directed by Engineer-in-charge. |
| 55 | M& L for MS Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment confirming to Fe 410-W (Gde E- 250) quality-A , complete all as per specified and as directed by Engineer-in-charge. |
| 56 | M&L for Mild steel TMT bars 10 mm dia. and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips, complete all as per specified and as directed by Engineer-in-charge. |
| 57 | M&L for Mild steel TMT bars 6 to 8 mm dia. cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips, complete all as per specified and as directed by Engineer-in-charge. |
| 58 | S&F Pre-painted galvalume aluminium zinc coating GI based corrugated or semi-corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws or J hooks, complete all as per specified and as directed by Engineer-in-charge. |
| 59 | M&L for Cutting out cracks to V-section in existing roofs or terracing, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight), complete all as specified and as directed by Engineer-in-charge. |
| 60 | M&L for water-proofing treatment to RCC roof slab including parapet, comprising the following course of treatment (applied from bottom to top):(a) Applying bituminous primer @ 0.40 litre per Sqm over prepared plastered surfaces of the roof including parapet surfaces.(b) Over the priming coat, laying one layer of APP-based polymeric membrane, 3 mm thick, weighing not less than 3.0 Kg/Sqm, reinforced with non-woven polyester fabric weighing not less than 160 gsm. The membrane shall be taken to a height of 60 cm (minimum) and then inserted inside the groove of the parapet.(c) Applying two coats of bituminous aluminium paint over the polymeric membrane after necessary preparation and cleaning.The laying of APP-based polymeric membrane shall be done by torch-on method or as per manufacturer’s instructions.Notes:(i) A minimum overlap of 100 mm shall be provided at the ends and 75 mm at the sides of the APP-based polymeric membrane and sealed as per manufacturer’s instructions.(ii) APP-based polymeric membrane shall be of approved quality conforming to the required specifications. |
| 61 | Providing & fixing false ceiling all heights with GRG (Glass Fibre Reinforced Gypsum) with semi perforated 12mm thick micro tegular edged GRG false ceiling tiles of Size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 476 (part 4 )-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of mainT runners of size 15 x 32 mm of length 3000mm, cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of size 600x 600mm , suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1OOOmm length and Lshape level adjuster of size 85x25x2mm.Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall I partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and complete all as per specified and as directed by Engineer-in-charge. |
| 62 | M&L for 25 mm thick for cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregates) as in floor finished even and smooth without using extra cement, complete all as per specified and as directed by Engineer-in-charge. |
| 63 | M&L for 25 mm thick PCC (1:2:4) type B-0 (12.50 mm graded stone aggregate) , as in under layer levelling course for Bath, WC floor below tiles finished even and rough, complete all as specified and as directed by Engineer-in-charge. |
| 64 | M&L for 75 mm thick PCC (1:3:6) type C-2 (using 40 mm graded crushed stone aggregate) as in plinth protection with saucer drain / footpath laid in panels and finished even and smooth with using extra cement including necessary form work complete all as specified and as directed by Engineer-in-charge.Note : Joints 12mm wide to the full depth of PCC shall be provided at every 3 meters and at every change of direction and shall be filled with mixture of bitumen and sand 1:3 by weight. Cost of this provision shall be deemed to be included in the quoted rate for concrete in plinth protection. |
| 65 | M&L for 100 mm thick PCC (1:4:8) type D2 (using 40 mm gradedcrushed stone aggregate) as in path/ steps complete all as specified and as directed by Engineer-in-charge. |
| 66 | M&L for 18 to 20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of granite stone including griding & polishing with complete all as specified and as directed by Engineer-in-charge.Note : Hole to be provided in granite slab for gas pipe in kitchen platform etc. |
| 67 | M&L for Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed in CM (1:6), complete all as per specified and as directed by Engineer-in-charge. |
| 68 | Ditto-all as per Item No.67.00 here-in-before but in skirting/dado over and including a backing coat of 10mm thick cement plaster in cement mortar (1:4), complete all as per specified and as directed by Engineer-in-charge. |
| 69 | M&L Chequered cement concrete tiles 30cm x 30cm x 25mm thick set jointed and pointed in with grey cement and pigmentlaid over floor and pointed in neat cement slurry in floors including 15 mm thick screed in CM (1:6), complete all as per specified and as directed by Engineer-in-charge. |
| 70 | M&L for coloured glazed ceramic tiles 350x 250x 7 mm/ 450X 350X 7mm thick, on vertical surfaces such as skirting, dados and risers to steps etc conforming to IS - 13712 grade IB-III, set and jointed in neat cement slurry and pointed in white or Coloured cement to match over 10 mm thick screed bed or bedding layers in CM 1:4 complete all as per specified and as directed by Engineer-in-charge. |
| 71 | S&F of coloured non-skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but notexceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shades of tiles over 15 mm thick screed bed or bedding layers in CM 1:6 complete all as per specified and as directed by Engineer-in-charge. |
| 72 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as per specified and as directed by Engineer-in-charge. |
| 73 | M&L for 20 mm thick plaster of cement mortar (1:4) rendering on fair faces of brick work in two layers (10mm+ 10mm) mixed with water proofing compound in top layer 200 ml per beg of cement or as per manufacturer\"s instructions finishing the surface fair and even without using extra cement complete all as specified and as directed by Engineer-in-charge.(Note: WPC shall be measured and paid separately as supply only under relevant item.) |
| 74 | M&L for 15 mm thick rendering on other than fair faces of brick work or concrete surface in cement mortar 1:6, and surface finished even and smooth (without using extra cement),complete all as specified and as directed by Engineer-in-charge. |
| 75 | M&L for 5mm thick rendering plastering on ceiling,chajja,slab fair faces ofconcrete surface in cement mortar (1:3) and surface even and smooth without using extra cement, complete all as specified and as directed by Engineer-in-charge. |
| 76 | M&L for preparing newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed by Engineer-in-charge. |
| 77 | M&L for applying two coats of oil emulsion distemper over a coat of alkali resistant primer over and including applying 1mm thick wall care putty newly plastered surfaces of wall after and including preparation of surfaces complete all as specified and directed. |
| 78 | M & L for preparing new Plasteredsurfaces of walls and finishing the walls with Acrylic smooth exterior paint of required shade : New work (Two or more coats applied @1.67 Ltr/10 Sqm over and including priming coat of exterior primer applied @ 2.20 Kg/ 10 sqm), complete all as per specified and as directed by Engineer-in-charge. |
| 79 | S&F of 4.8 mm thick sheet glass of ordinary quality in squares exc. 0.5 sqm in each pane glazing with oil putty, extra over sheet glass, ordinary quality, if sheet glass is ground or obscured or frosted, on one side complete all as per specified and as directed by Engineer-in-charge. |
| 80 | M&L for preparation of new or previously untreated wood or wood based surfaces of any description, exceeding 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as per specified and as directed by Engineer-in-charge. |
| 81 | M&L for preparation of new or previously untreated steel or iron surface of any description and applying two coats of synthetic enamel paint over a coat of red oxide, primer over 10cm width or girth complete all as specified and as directed by Engineer-in-charge. |
| 82 | M&L for 20 mm Drilling and tapping cast iron water mains (in position) for branch connections of the internal dia, complete all as per specified and as directed by Engineer-in-charge. |
| 83 | S&F in repair of Vitreous China Ware Wash hand basin white, flat back, size 550 x 400 mm size(flat back or angle back type) including cutting for and pinning ends of brackets and including, waste pipe, CP waste coupling etc., complete all as per specified and as directed by Engineer-in-charge. |
| 84 | S&F in repair of 15mm dia bore fancy type pillar tap cast copper alloy with capstan heads chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly-nuts, screwed for iron pipe complete all as per specified and as directed by Engineer-in-charge. |
| 85 | M&L for Straight plain brass ferrules (or connecting screws) screwed both ends and fixed includingall necessary fitting such as nippel, reducer socket, socket etc. complete all as specified and as directed by Engr-in-Charge. |
| 86 | S&F of 20 mm ballvalves, high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minimum weight 15mm-142gms/ 20 mm - 210gms/25mm-455gms/ 40mm - 690 gms) and fixed in position complete all as per specified and as directed by Engineer-in-charge. |
| 87 | S&F in repairs of 600x450mm bevelled edge mirror of selected quality glass, mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as per specified and as directed by Engineer-in-charge. |
| 88 | S&F in repair of Bib taps long body fancy type cast copper alloy, chromium plated for 15mm bore pipe, screwed for iron pipes or for brass ferrule, complete all as per specified and as directed by Engineer-in-charge. |
| 89 | S&F in repair of Stop valves, cast copper alloy, fancy type, chromium plated with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as per specified and as directed by Engineer-in-charge. |
| 90 | S&F in repairs of Gun-metal 20 mm bore pipe, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as per specified and as directed by Engineer-in-charge. |
| 91 | S&F in repairs of PVC connection 15mm dia with PTMT nuts of length 600 mm, complete all as per specified and as directed by Engineer-in-charge. |
| 92 | S&F in repair of two way bib cock with wall flange chromium plated with crutch or butterfly handle screwed down screwed for iron pipe 15 mm bore and fixed, complete all as per specified and as directed by Engineer-in-charge. |
| 93 | S&F in repair of 15 mm bore angle cock CP with flange complete all as per specified and as directed by Engineer-in-charge. |
| 94 | S&F of rotational moulded PVC water storage tank 1000 litres capacity conforming to IS-12701(1989) cylindrical vertical type multi-layered with closed top including inlet, outlet and wash out holes of approved make hoisted and fixed in position all as specified in SSR Part-I, 2009 etc., complete all as per specified and as directed by Engineer-in-charge. |
| 95 | Supply and laying of GI tube 15 mm bore medium grade with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by Engineer-in-charge. |
| 96 | S&F of GI tube 20 mm bore medium grade with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by Engineer-in-charge. |
| 97 | Supply and laying of GI tube 20 mm bore medium grade with fittings and fixed in trenches, complete all as specified and as directed by Engineer-in-charge. |
| 98 | M&L for salt-glazed stoneware gully traps, square or round mouthed, type `P\" 150x100mm complete all as directed by Engr-in-Charge |
| 99 | S & F in repair of sink without drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers; including bedding in cementmortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe over all size 495mm x 420mm bowl size 410mm x 330mm x 160mm, complete all as per specified and as directed by Engineer-in-charge. |
| 100 | S&F in repair of toilet paper holder with flat recessed type stainless steel including all necessary fittings, complete all as per specified and as directed by Engineer-in-charge. |
| 101 | S&F in repair of PVC valveless, symphonic action type 10 litre capacity low level flushing cistern, white, with inlet, ball valve, float and handle including brackets and 32 mm bore PVC flush pipe, complete all as per specified and as directed by Engineer-in-charge. |
| 102 | S&F in repair of Vitreous China wash down water closet pan (pedestal pattern), white, including connection to drain (or outgoing pipe) and to flushing pipe, anti siphonage pipe, etc., complete all as per specified and as directed by Engineer-in-charge. |
| 103 | S&F of plastic water closet seat cover, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, complete all as per specified and as directed by Engineer-in-charge. |
| 104 | S&F in repair of 75mm PVC (SWR) floor trap with grating including jointing with solvent cement complete all as per specified and as directed by Engineer-in-charge. |
| 105 | S&F of 110 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls or laid in trenches/floor, complete all as per specified and as directed by Engineer-in-charge. |
| 106 | S&F of PVC (SWR) 110 mm bore bends with access door complete all as per specified and as directed by Engineer-in-charge. |
| 107 | S&F of 75 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls or laid in trenches/floor, complete all as per specified and as directed by Engineer-in-charge. |
| 108 | S&F of 110mm dia PVC (SWR) branch piece single (single \"Y\") equal or unequal with access door complete all as per specified and as directed by Engineer-in-charge. |
| 109 | S&F 110mm dia PVC SWR vent cowl complete all as per specified and as directed by Engineer-in-charge. |
| 110 | S&F of 75 mm dia bore PVC (SWR) junction (single T) equal or un-equal with access door, complete all as per specified and as directed by Engineer-in-charge. |
| 111 | S&F of PVC (SWR) 75 mm bore bends complete all as per specified and as directed by Engineer-in-charge. |
| 112 | S&F in repair of Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position, complete all as per specified and as directed by Engineer-in-charge. |
| 113 | S & F in repair stainless steel Soap dish, complete all as per specified and as directed by Engineer-in-charge. |
| 114 | S&F in repairs Brass chromium plated shower rose 150 mm size with or without swivel joints, any size, including fixing to steel pipe or union, complete all as per specified and as directed by Engineer-in-charge. |
| 115 | S&F in repair of glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chomium plated bracket guard & railing 60 cm long, complete all as per specified and as directed by Engineer-in-charge. |
| 116 | Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed by Engineer-in-charge. |
| 117 | Surface Preparation and removal of Loose Concrete : Removing & Hacking of existing concrete Carefully by low impact high frequency hammer OR by manual chipping without damaging the existing concrete or control sand blasting including cleaning the surfaces by air jet etc. complete all as specified and as directed by Engineer-in-charge.(Mode of measurement- per sqmt of breaking area of concrete ) |
| 118 | Bonding Agent: Supply and applying a bond of Fosroc Nitobond SBR Latex, or Equivalent SBR Latex based bonding agent admix with cement as per manufacturer recommended ratio.complete all as specified and as directed by Engineer-in-charge. |
| 119 | Patch Repair Work by Polymer modified mortar : Repair ofconcrete surface with single component, fibre reinforced shrinkage compensated, polymer modified structural grade repair mortar like Fosroc Renderoc SP 40 or equivalent at a thickness of 25 mm. The repair mortar should have a compressive strength 45 N/mm²,flexture strength 7 N/mm² and tensile strength 2.5 N/mm² at 28 days,complete all as specified and as directed by Engineer-in-charge. |
| 120 | SCH \"A\" PART-II (E/M WORK)Taking down carefully old unserviceable copper/ aluminium point wiring (light, exhaust fan, socket or power) complete incl fittings such as switches, ceiling roses, pendants, regulators, bells, sockets, tube light fittings etc., and making good disturbed surface of walls & floors etc., complete all as per specified and as directed by Engineer-in-charge. |
| 121 | M&Lfor point wiringcomplete with 1.5 sqmm PVC insulated, FRLS type, ISI marked, conforming to IS-694/1990 unsheathed,multistranded,single core, copperconductor cable 1100 volts grade colour code cablesdrawn through and including PVCConduit 20 mm dia medium grade (MMS) andincluding cutting, chasing work at any height and all accessoriesconcealedinwalls / roofs / floors / ceiling etc. flush mountingMS box with top, bottom, side/back wall knockout for conduitentry from any direction made out of 1.60mm thick and 50mm depth suitable for fixing ofmodular top cover , blankingplate as per numbers of switch modules, modular switches, sockets, fan regulators, red colour indicator, blank plates etc as approved colouresmodular accessories of suitable modules andincluding 1.5 Sqmm PVC insulated multistranded FRLS type unsheathedsingle core cable with copper conductor cable as earth continuity conductor andconnecting to common earth dolly and including making good the disturbed surfaces to match with existing surfaces by applying white/colour wash/distemper as applicable after applying of putty for smooth finish surfacecomplete all as specified and directedfor one light point controlled by one way switch, complete all as per specified and as directed by Engineer-in-charge.(Note:- (i) Allnecessary accessories such asmodular box, top cover plate, blank plate, MS box, screws, washers etcare to be used of same make/brand onlyin relevant items.(ii) Cutting & chasingof wall for point wiring at any height shall be done and cost of the same deemed to be including with quoted rate.) |
| 122 | All as per serial item No. 121 above but for one ceiling/exhaust fan point controlled by one switch. |
| 123 | All as per serial item No. 121 above but for one socket outlet 5/6 AMPs on same board. |
| 124 | All as per serial item No. 121 above but for one socket outlet 5/6 AMPs on independent board. |
| 125 | All as per serial item No. 121 above but for one Bell point controlled by one switch, complete all as specified and as directed by Engineer-in-charge. |
| 126 | All as per serial item No. 121 abovebut with 2.5 sqmm single core copper conductor for one socket out let 15/16 AMPs point on the independent board, complete all as per specified and as directed by Engineer-in-charge. |
| 127 | All as per serial item No. 121here in before but wiring with two single core, multistranded copper conductor of size 4.00 sqmm for 15/16 A socket out let point on independent board, complete all as specified and as directed by Engineer-in-charge. |
| 128 | S&F of Modular switch, single pole, one way, 10 Amp, 1 Module, 230 volt, ISI marked, complete all as per specified and as directed by Engineer-in-charge. |
| 129 | S&F of Modular shutter socket outlet 5 pin, 6/10 Amps, 2 module, 230 volts, ISI marked, complete all as per specified and as directed by Engineer-in-charge. |
| 130 | S&F of Modular shutter socket outlet 6 pin, 6/16 Amps, 2 module, 230 volts, ISI marked, complete all as per specified and as directed by Engineer-in-charge. |
| 131 | S&F of Modular Switch single pole, one way, 16/20 Amps, 1 module, 230 volts, ISI marked, complete all as per specified and as directed by Engineer-in-charge. |
| 132 | S&F of Modular Bell push 10 Amp, 1 Module, 230 volt, ISI marked, complete all as specified and as directed by Engineer-in-charge. |
| 133 | Supply and of fix ceiling rose surface PVC three terminals, PVC/ polycarbonate, insulated body, complete all as per specified and as directed by Engineer-in-charge. |
| 134 | Supply and fix of Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed by Engineer-in-charge. |
| 135 | S&F of modular electronic step regulator (speed regulation in 5 steps) 120W - 2 module suitable for ceiling fan 1200 sweep/1400 mm, complete all as per specified and as directed by Engineer-in-charge. |
| 136 | Supply and fix LED tube light fittings1 x 20 Watt, 4 feet long, 220 V, AC decorative box type with driver holder including LED tube rodconnecting up with three core flexible copper conductor cable from ceiling rose to tube light fitting complete all as specified and as directed by Engineer-in-charge. |
| 137 | Supply and fixing of LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and as directed by Engineer-in-charge. |
| 138 | Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection including taking down old unserviceable street light, complete all as specified and as directed by Engineer-in-charge. |
| 139 | Supply and fixing of ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC), complete all as per specified and as directed by Engineer-in-charge. |
| 140 | Supply and fix of exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm, complete all as specified and as directed by Engineer-in-charge. |
| 141 | Supply and fixing ofelectric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc., complete all as specified and as directed by Engineer-in-charge. |
| 142 | S&F of MCB TPN 40 Amp to 63Amp four pole 415 volt breaking capacity 16KA adjustable thermal and adjustable magnetic, complete all as specified and as directed by Engineer-in-charge. |
| 143 | Supply and fix of Single pole and neutral, 240 Volt, 20Amp, enclosure with a two pin and earth plug and socket complete with one single pole MCB, complete all as specified and as directed by Engineer-in-charge. |
| 144 | Supply and fix sheet metal enclosure powder painted for MCB SPN 12 way double door DB with din rail and suitable bus bar including cutting chases for DB of reqd size and making good distrubed surface area and putting blanking plate, including taking down old unserviceable DB, complete all as specified and as directed by Engineer-in-charge. |
| 145 | Supply and fix sheet metal enclosure powder painted for MCB TP & N 4 way double door DB, 415 Volts, 200 Amp with din rail and bus bar including making good to the disturbed surface matching with the existing complete all as specified and as directed by Engineer-in-charge. |
| 146 | Supply and fixing of amp rating 240V, 10KA \"C\" curve miniature circuit breaker (MCB) of SPN 40 to 63 AMP and current carrying capacity in the MCB DB complete with connection testing complete all as specified and as directed by Engineer-in-charge. |
| 147 | Supply and fixing of amp rating 240V, 10KA \"C\" curve miniature circuit breaker (MCB) of SP 6 To 32 AMP current carrying capacity in the MCB DB complete with connection testing and commissioning, complete all as specified and as directed by Engineer-in-charge. |
| 148 | M&L for earthing with glavanised steel earth plate electrode of size 600mmX600mmX6mm thick buried directly in ground (earth pit not less than 2.25 m deep below the ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to the galvanised earth lead by means of bolts, nuts, check nutsand washers of galvanisediron or steel using GI or steel wire 4mm dia as earthing lead as shown in electrical plate No.3 of SSR Part-I connected to earthing test point all specified or indicated including testing on completion including necessary excavation and earth work in soft/loose soil, returning filling, disposalof surplus soil, earth pit in PCC (1:3:6) type C-1 using 20mm graded stone aggregate pit, funnel, 20mm dia GI medium grade watering pipe , 15mm dia GI medium grade earth lead protection pipe and pre-cast earth pit cover 50mm thick made of RCC (1:1.5:3) type A-1 duly reinforced with 8mm dia TMT bar @150c/c both ways, one lifting handle made out of 10mm dia TMT bar 250 mm long embedded in cover slab and cover, wire, copper lugs etc mesh, charcoal and common salt in alternate layer of 15 cm thick including taking down old earthing completeall as specified and directed.(Notre: Galvanised iron wire of 4mm dia upto 7.5m long including testingis deemed to be included with quoted rate). |
| 149 | M&L for sub main wiring complete with 2 run of 6 sqmm single core copper conductor (ISI marked) cable1100 volts grade, FRLS type, PVC insulated, unsheathed, flexible, multi strandedcolour coded cables drawn through and including rigid PVC conduit of required sizemedium grade (MMS) with all connected accessories such asBend, Tee, Elbow, Short piecesetc concealed in wall/roofs/floorsand including one run of 6 sqmmsingle core copper conductor cable flexible, PVC insulated, unsheathed, multistranded, 1100 volts grade, FRLS type as earth continuity conductor connected to common earth dolly and including chease cutting and filling the same with cement mortar and finished with putty and making good the disturbed surfaces to match with existing surfaceas requiredfor concealedworkincluding taking down old unseviceable sub main wiring, complete all as specified and directed .(Note: (i) Two runs of cable with one run earth wire and PVC conduit shall be measured as one length. (ii) Extra length of cable required for connection to DBs shall be deemed to be included in the unit rate and shall not be measured separately. (iii) Earth wire shall run inside the conduit. (iv) Suitable color code of wire must be ensured for phase/netural/earth. (v) All surface cutting/making good for wiring/switch board/junction box/DB etc are included with unit quoted rate.) |
| 150 | S&F of street light bracket made out of GI tubing 25 mm bore medium grade 1.20 Mtr long bend to required shape as in bracket for street light fittings fixed with two No of MS flat iron 25mm x 5mm size and 30cm long clamp of required shape with bolts nuts and washers suitable for building security light including painting of mild steel flat iron surfaces with two coats of aluminium paint over a coat of red oxide primer, including taking down old unserviceable GI bracket, complete all as specified and as directed by Engineer-in-charge. |
| 151 | S&F XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminum conductor, 1100Volt grade on walls with fixing acessories of size 16 Sqmm4 Core cable including taking down old cable, complete all as per specified and as directed by Engineer-in-charge.(NOTE: Excavation/earth work, sand cushioning, cable cover/brick shall be measured and paid separately if required) |
| 152 | Supply & Laying of Sub-Class B Bricks, well burnt, laid breadth wise along the length of cable laid in trenches over sand cushion laid for UG cable protection, complete all as per specified and as directed by Engineer-in-charge. |
| 153 | M&L for sand cushioning to under ground cable in trenches/existing cable trenches/ductsin layers of 8 cm deep before laying the cable and 15 cm deep including required watering and consolidation after laying and stretching the cable complete all as specified and directed. (Note: Only punned down volume of sand to be measured)NOTE:-The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule \"A\"/BOQ. |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
