|
| 1 | CIVIL WORKS |
| 2 | Earthwork in excavation by mechanical means (hydraulic excavator)/manual means in foundation pipeline trenches drain (not exceeding 1.5 m in width or 10 sq.m. on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directedwithin a lead of 50m.All kinds of soil |
| 3 | Rubble packing with hard laterite stone under floors including watering ramming and consolidating etc. in pipeline trenches and other foundations complete. |
| 4 | Providing and laying in position cement concrete 1:2:4 (1 cement : 2 coarse sand: 4 graded granitic or basaltic stone aggregate 40 m nominal size) excluding cost of centering, shuttering and finishing : All works upto plinth level |
| 5 | Centering & shuttering including Strutting, Propping & removal of forms for :Foundations, Footings, Bases for columns |
| 6 | Providing and laying in position ready mixed concrete (RMC) with usage of Ordinary Portland Cement manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead upto 10kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C., from the transit mixer to the site of laying, excluding the cost of centering, shuttering, finishing and reinforcement including the cost of admixtures in recommended porportions as per IS : 9103 to accelerate/retard setting of concrete, improve workability without imparing strength and durability as per the directions of the engineer-in-charge. All works upto floor V level. M-20 grade of concrete |
| 7 | Providing TMT steel reinforcement bars of (SAIL, TATA. VIZAG, JSW Steel Ltd.) ) (Confirming to IS 1786 of 1986) for RCC work (conforming to I.S. 1786 of 1986) including bending, binding & placing in position in all the floors along with the factory made precast concrete cover blocks of specified sizes whose compressive strength is not less than that of surrounding concrete in the structural member. |
| 8 | Electrical work |
| 9 | Supply of 6M decorative Single Arm Cameroon pole with 72W Sabik Ø480mm Crown TM PC:- 6M height designer decorative single arm pole made in combination of steel pipe which is fabricated using 114 mm(+/-3%)dia grooved pipe x 4mm thick base section with Minimum height of 2000mm. The pole is to be provided with a surface mounting suitable base plate dia of 350 mm and suitable thickness as per IS standards and structural reports. Decorative knob on the top is made of cast aluminium in single piece of minimum height >360mm. The pole should be provided with an inbuilt junction box to fix Four-way connector and 6A MCB at the bottom - the inbuilt box should have a flush door of suitable size. The decorative pedestal to be mounted on a suitable size steel plate. The Pole shall be hot dip galvanized. . The suitable size foundation bolt shall be supply along with the pole of EN 8 grade. The manufacturer needs to provide a structural analysis for structural stability of the pole with the relevant IS standards IS 1239/1161/E250 needs to be clearly mentioned. The same needs to be confirmed in form of Test Certificates from the manufacturer. Internal wiring backelite sheet and MCB included Please refer the attached drawing no – Cameroon 6M SA TM Pole. Including 72W post top fixture suitable to mount 72W ± 10% with MCPCB of not less than 1.6 mm thickness and Cu of 35 microns and 2.5 Thermal conductivity for fixture. The LED used should be high power Epoxy LEDs (Make- Osram/bridgelux/nichia/cree) with Macadam /= 70 and CCT 4000K. The luminaire should have System efficacy (Lumens/watt) >110 lumens/watt. The luminaire should be having a warranty for a period of 5 years against any manufacturing defects. The manufacturer should have internal testing equipment’s especially 2m Integrating Sphere, IPX6, IK10, Humidity Chamber. The manufacturer shall submit the LM 80 report for LED used in the fixtures. Similar to Model no. Sabik Ø480mm Crown TM PC Clear SL. The luminaire should be RoHS compliant as per Government notification and with a valid BIS Number. Luminaire Make REYTEK, suncity, k-lite, dwarka casting, havells as directed by the engineer inchrage. |
| 10 | Street Light Panel: SITC of LT panel IP- 67 outdoor type,floor mounted Panel, shall be suitable for 415 V, 3 phase, 4 wire, 50Hz Supply system. With 3 phase energy meter and 63A TPN MCB as incommer and 11 nos of 16 A TPN MCB as outgoing with 3 numbers of microcontoller based 25 A programmable digital Almac timer as directed by engineer in-charge. |
| 11 | Supply of high quality Static White (3000K) Linear Wall Washer in 1000mm having precies beam angle as per design or site requirement suitable for façade lighting applications. Housing to be made of extruded Aluminium alloy with excellent heat management system to ensure proper heat dissipation and thermal stability of the luminaire. The luminaire shall have electrostatically applied polyester powder coating finish. Luminaire shall be suitable to operate in a temperature range of -10°C to 50°C, LED life should be at least 50,000 burning hours at L70 at 25°C. The lens shall be made of anti-aging & anti UV-PMMA/PC material and able to minimize hot spots to insure proper light distribution. Suitable for outdoor weather proof conditions having IP66 ingress protection. Transparent toughened glass having impact resistance protection of IK08. The luminaire shall have system wattage not exceeding 36W and system lumen output of not less than 2910 lumens, Beam angle should be 10x60 /15x45/25 Degree/As per site condition, The fixture shall have input voltage of 24V DC, provided with external high efficiency Driver operating on 240V AC, Power factor >0.90 @ full Load, internal Surge protection 4KV and other protections including OCP, OVP, SCP, OTP shall be provided in the driver. Luminaire complying to BIS standard \"IS 10322\" ,Color Temperature : 3000K, CRI>80,, Operating Temperature : -10°C to +50°C, Operating Humidity : 10%-90%, LED Makes should be CREE, LumilLED, Osram, Nichia, Bridgelux to insure higher lumen output and brightness with SMD LED chips. The manufacturer should have internal testing equipment’s especial 2m Integrating Sphere, IPX6, IK10, Humidity Chamber. The manufacturere shall submit the LM79 & LM 80 report along with the supply of material along with the BIS certificate. Make: REYTEK, leksa, la-lumirie,phillips,havells as directed by the engineer incharge. |
| 12 | Supply of high quality Static White (3000K) Linear Wall Washer in 1000mm having precies beam angle as per design or site requirement suitable for façade lighting applications. Housing to be made of extruded Aluminium alloy with excellent heat management system to ensure proper heat dissipation and thermal stability of the luminaire. The luminaire shall have electrostatically applied polyester powder coating finish. Luminaire shall be suitable to operate in a temperature range of -10°C to 50°C, LED life should be at least 50,000 burning hours at L70 at 25°C. The lens shall be made of anti-aging & anti UV-PMMA/PC material and able to minimize hot spots to insure proper light distribution. Suitable for outdoor weather proof conditions having IP66 ingress protection. Transparent toughened glass having impact resistance protection of IK08. The luminaire shall have system wattage not exceeding 18W and system lumen output of not less than 1490 lumens, Beam angle should be 10x60 /15x45/25 Degree/As per site condition, The fixture shall have input voltage of 24V DC, provided with external high efficiency Driver operating on 240V AC, Power factor >0.90 @ full Load, internal Surge protection 4KV and other protections including OCP, OVP, SCP, OTP shall be provided in the driver. Luminaire complying to BIS standard \"IS 10322\" ,Color Temperature : 3000K, CRI>80,, Operating Temperature : -10°C to +50°C, Operating Humidity : 10%-90%, LED Makes should be CREE, LumilLED, Osram, Nichia, Bridgelux to insure higher lumen output and brightness with SMD LED chips. The manufacturer should have internal testing equipment’s especial 2m Integrating Sphere, IPX6, IK10, Humidity Chamber. The manufacturere shall submit the LM79 & LM 80 report along with the supply of material along with the BIS certificate. Make REYTEK, suncity, k-lite, dwarka casting, havells as directed by the engineer inchrage. |
| 13 | Supply of high quality Static White (3000K) Linear Wall Washer in 500mm having precies beam angle as per design or site requirement suitable for façade lighting applications. Housing to be made of extruded Aluminium alloy with excellent heat management system to ensure proper heat dissipation and thermal stability of the luminaire. The luminaire shall have electrostatically applied polyester powder coating finish. Luminaire shall be suitable to operate in a temperature range of -10°C to 50°C, LED life should be at least 50,000 burning hours at L70 at 25°C. The lens shall be made of anti-aging & anti UV-PMMA/PC material and able to minimize hot spots to insure proper light distribution. Suitable for outdoor weather proof conditions having IP66 ingress protection. Transparent toughened glass having impact resistance protection of IK08. The luminaire shall have system wattage not exceeding 12W and system lumen output of not less than 980 lumens, Beam angle should be 10x60 /15x45/25 Degree/As per site condition, The fixture shall have input voltage of 24V DC, provided with external high efficiency Driver operating on 240V AC, Power factor >0.90 @ full Load, internal Surge protection 4KV and other protections including OCP, OVP, SCP, OTP shall be provided in the driver. Luminaire complying to BIS standard \"IS 10322\" ,Color Temperature : 3000K, CRI>80,, Operating Temperature : -10°C to +50°C, Operating Humidity : 10%-90%, LED Makes should be CREE, LumilLED, Osram, Nichia, Bridgelux to insure higher lumen output and brightness with SMD LED chips. The manufacturer should have internal testing equipment’s especial 2m Integrating Sphere, IPX6, IK10, Humidity Chamber. The manufacturere shall submit the LM79 & LM 80 report along with the supply of material along with the BIS certificate. Make: Make REYTEK, suncity, k-lite, dwarka casting, havells as directed by the engineer inchrage. |
| 14 | Supply of high quality Static White (3000K) Floodlight projector having precies beam angle as per design or site requirement suitable for façade lighting applications. Housing to be made of pressure die-cast Aluminium with excellent heat management system to ensure proper heat dissipation and thermal stability of the luminaire. The luminaire shall have electrostatically applied polyester powder coating finish. Luminaire shall be suitable to operate in a temperature range of -10°C to 50°C, LED life should be at least 50,000 burning hours at L70 at 25°C. The lens shall be made of anti-aging & anti UV-PMMA/PC material and able to minimize hot spots & insure proper light distribution. Suitable for outdoor weather proof conditions having IP66 ingress protection. Transparent toughened glass having impact resistance protection of IK08. The luminaire shall have system wattage 36W and system lumen output of not less than 3020 lumens, Beam angle should be narrow : 15/25/40 Degree/As per site condition, The fixture shall have input voltage of 240V AC, provided with internal high efficiency Driver operating on 240V AC, Power factor >0.90 @ Full Load, internal Surge protection 4KV and other protections including OCP, OVP, SCP, OTP shall be provided in the driver complying to BIS standard \"IS 10322 ,Color Temperature : 3000K CRI > 70, Operating Temperature : -10°C to +50°C, Operating Humidity : 10%-90%, LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia, Bridgelux to insure higher lumen output and brightness with SMD/COB LED chips. The successful bidder shall submit the product data sheets, LM80 report issued by LED manufacturer along with the BIS certificate.Make: Make REYTEK, suncity, k-lite, dwarka casting, havells as directed by the engineer inchrage. |
| 15 | Supply of high quality Static White (3000K) Floodlight projector having precies beam angle as per design or site requirement suitable for façade lighting applications. Housing to be made of pressure die-cast Aluminium with excellent heat management system to ensure proper heat dissipation and thermal stability of the luminaire. The luminaire shall have electrostatically applied polyester powder coating finish. Luminaire shall be suitable to operate in a temperature range of -10°C to 50°C, LED life should be at least 50,000 burning hours at L70 at 25°C. The lens shall be made of anti-aging & anti UV-PMMA/PC material and able to minimize hot spots & insure proper light distribution. Suitable for outdoor weather proof conditions having IP66 ingress protection. Transparent toughened glass having impact resistance protection of IK08. The luminaire shall have system wattage 18W and system lumen output of not less than 1550 lumens, Beam angle should be narrow : 15/25/40 Degree/As per site condition, The fixture shall have input voltage of 240V AC, provided with internal high efficiency Driver operating on 240V AC, Power factor >0.90 @ Full Load, internal Surge protection 4KV and other protections including OCP, OVP, SCP, OTP shall be provided in the driver complying to BIS standard \"IS 10322 ,Color Temperature : 3000K CRI > 70, Operating Temperature : -10°C to +50°C, Operating Humidity : 10%-90%, LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia, Bridgelux to insure higher lumen output and brightness with SMD/COB LED chips. The successful bidder shall submit the product data sheets, LM80 report issued by LED manufacturer along with the BIS certificate. Make: Make REYTEK, suncity, k-lite, dwarka casting, havells as directed by the engineer inchrage. |
| 16 | Supply of Static white 3000K Neon Flex with diffused and homogenous light suitable for outdoor applications of Façade Lighting. Silicon extrusion Flexible tubes with side bending option. Silicon extrusion technology having advanced process, with high-efficiency production capacity and environmentally-friendly characteristics. Additionally, withhigh grade appearance, soft bend flexibility, strong impact resistant and high weather resistance. Uniform, dot-free and smooth lighting performance up to 5M. On field cuttable and assembly, with endcap sealed by gluing process. Power Consumption should be between 12~14W/m and have atleast 120 Led\"s per meter with 120° beam angle. Ingress Protection should be IP 67. and IK rating IK07. Size 10mm x20mm side bend. Dimmable available with PWM signal. Operating Temperature: -10°C to 45°C. The fixture shall have input voltage for 24V DC, with external high efficiency driver having power factor >0.90, Surge protection 4KV and other protections including OCP, OVP, SCP, OTP shall be provided. The lumen maintenance L70@ 25 °C of the LED shall not be less than 70% of the initial lumen after 30,000 burning hours, with suitable aluminium mounting profile.* Power supply: DC 24V * Operating Temperature range: -10°C to +45°C * LED make: CREE/ OSRAM/ LUMILED/ SEOUL/ NICHIA/Sanan/Epistar Make: Make REYTEK, suncity, k-lite, dwarka casting, havells as directed by the engineer inchrage. |
| 17 | SITC of Smart lighting panel |
| 18 | Supplyof 3M decorative Single Arm Cameroon pole with 72W Sabik Ø480mm Crown TM PC:- 6M height designer decorative single arm pole made in combination of steel pipe which is fabricated using 114 mm(+/-3%)dia grooved pipe x 4mm thick base section with Minimum height of 2000mm. The pole is to be provided with a surface mounting suitable base plate dia of 350 mm and suitable thickness as per IS standards and structural reports. Decorative knob on the top is made of cast aluminium in single piece of minimum height >360mm. The pole should be provided with an inbuilt junction box to fix Four-way connector and 6A MCB at the bottom - the inbuilt box should have a flush door of suitable size. The decorative pedestal to be mounted on a suitable size steel plate. The Pole shall be hot dip galvanized. . The suitable size foundation bolt shall be supply along with the pole of EN 8 grade. The manufacturer needs to provide a structural analysis for structural stability of the pole with the relevant IS standards IS 1239/1161/E250 needs to be clearly mentioned. The same needs to be confirmed in form of Test Certificates from the manufacturer. Internal wiring backelite sheet and MCB included Please refer the attached drawing no – Cameroon 6M SA TM Pole. Including 72W post top fixture suitable to mount 72W ± 10% with MCPCB of not less than 1.6 mm thickness and Cu of 35 microns and 2.5 Thermal conductivity for fixture. The LED used should be high power Epoxy LEDs (Make- Osram/bridgelux/nichia/cree) with Macadam /= 70 and CCT 4000K. The luminaire should have System efficacy (Lumens/watt) >110 lumens/watt. The luminaire should be having a warranty for a period of 5 years against any manufacturing defects. The manufacturer should have internal testing equipment’s especially 2m Integrating Sphere, IPX6, IK10, Humidity Chamber. The manufacturer shall submit the LM 80 report for LED used in the fixtures. Similar to Model no. Sabik Ø480mm Crown TM PC Clear SL. The luminaire should be RoHS compliant as per Government notification and with a valid BIS Number. Luminaire Make REYTEK, suncity, k-lite, dwarka casting, havells as directed by the engineer inchrage. |
| 19 | SITC of junction box including terminations of size 130 x130 x 77 mm of make hensel |
| 20 | Charges for installation testing and commissioning of all light fixtures of façade illumination of Shantadurga Temple and Mahamaya Temple. |
| 21 | Supply of 4 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size.4 core25sq.mm |
| 22 | Supply of 3 core unarmoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size.3 Core 2.5 sq.mm |
| 23 | Supply of 4 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size.4 core10sq.mm |
| 24 | Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm on surface, etc. complete as required |
| 25 | Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm direct in ground including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable) and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required.(a) In soily strata |
| 26 | Supplying and laying 6 SWG GI wire at 0.5 m below ground level for conductor earth electrode including soldering etc. as required |
| 27 | Supply and making cable end terminations with compression gland and aluminium lugs for following sizes of PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. (4) 2 X 10sq.mm |
| 28 | Supply and making cable end terminations with compression gland and aluminium lugs for following sizes of PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. (6) 2 X 25sq.mm |
| 29 | Earthing with GI earth pipe 2 mts long 40 mm dia medium class with ISI mark,of approved brands, including accessories and providing masonry enclosure with CI/RCC cover having locking /lifting arrangement and watering pipe etc. with charcoal or coke and salt) as required as per the Earthing Drawing provided by the Engineer-Incharge.The scope of work includes the following: a) Excavation of pit of size 1.0x1.0x 2.0 mtrs(min) and disposal of excavated soil. b) Class B GI pipe, 40mm diameter as per specifications. c) Charcoal/salt as per specs. d) Refilling the pit of size 1.0x1.0x 2.0 mtrs(min) with soft black soil of minimum resistivity i/c transportation. e)Masonary chamber with proper foundation, cover plate and locking arrangement. f) Testing of earth value with earth megger and certifications of its value. Aluminium tag with embossed earthing value to be attached to the pipe. g)watering arrangement(plumbing will be paid seperately).(a) In soily strata |
| 30 | Supplying and laying 25 mm x 5 mm GI strip in 40 mm dia GI pipe from earth electrode as required |
| 31 | Supply, installation, testing & commissioning of Diesel Generator Set 25kva @20 Kwe with Volvo Eicher engine, Canopy made of composite polymer-based material, Glass Reinforced Polymer (GRP) acoustic enclosure which can be recycled when replaced having Canopy Dimension of 2825x1090x1425mm (LxWxH) with total canopy weight not exceeding 900kg. Output continuous rating 3 ph, 415V, 50 hz 0.8 p. f A.C Supply. A totally enclosed water cooled 4-cylinder engine developing 38 BHP at 1500 RPM with 10% overload for 1hour in 12 hours. The Generator canopy shall be of non-metallic, non-rusting i.e. corrosion free, weatherproof, material suitable for coastal and high humidity conditions. The DG Set shall comply with CPCB IV+ noise norm with sound absorbing material to restrict sound level up to 75Db at 1.0m with the silencer positioned inside the canopy. The canopy shall maintain certified sound level for minimum of 15 years. The inbuilt tank fuel capacity at 85 litres & maximum fuel consumption 5.3 ltr/ hr @ 75% loading. The Generator & panel Canopy material shall contain fire resistant, additives with self -extinguishing and non -conductive properties. the controller should be fixed in GRP panel box having metal hinges with SS finish should be welded from inside of box size of 650x450x200mm with box having powder coated in RAL9001 mounted at rear side at height of 954mm from ground level. The DG should come with low Vibration as per IS8528 part 9 & should be Aesthetically pleasing in colour combination of white & Anthracite grey for canopy with RAL9001 -RAL 7016 respectively with base frame size of 285mm made up of 2.5mm thickness in RAL 9005 maintaining 2 coat of Primer & 1 coat of Painting Process thickness 80microns. All the painting shall be done by qualified painters. Reference to CAT No- GRP PKGVEF-IV25 Paikane Make or Equivalent. |
| 32 | Supplying and erecting Outdoor type 5 to 7 W LED Focus light fitting complete with IP67, 24VDC, 60w driver, / power supply (if any), connecting wire, including gear box and junction box for cable connectionwith all necessary accessories and Coated with epoxy zinc phosphate primer and finished using environmentally stable polyurethane based paint .Beam angle requirement as per GTDC with 3000K CCT of suitable make Wipro,Legero,Bajaj,Jaquar,VIN LED,K-lite,Philips Complete with all required accessories . |
| 33 | Supplying and erecting 15 W wall/Column-mounted Rectangular type LED downlight IP 65 having Extruded and Die cast aluminium housing with high corrosion resistance surface finish with Integral control gear and beam angles - narrow, medium, wide ,with 3000K CCT of suitable make Wipro,Legero,Bajaj,Jaquar,VIN LED,K-lite,Philips. Complete with all required accessories . |
| 34 | Supply of high quality Static White (3000K) Linear Wall Washer in 1000mm having precies beam angle as per design or site requirement suitable for façade lighting applications. Housing to be made of extruded Aluminium alloy with excellent heat management system to ensure proper heat dissipation and thermal stability of the luminaire. The luminaire shall have electrostatically applied polyester powder coating finish. Luminaire shall be suitable to operate in a temperature range of -10°C to 50°C, LED life should be at least 50,000 burning hours at L70 at 25°C. The lens shall be made of anti-aging & anti UV-PMMA/PC material and able to minimize hot spots to insure proper light distribution. Suitable for outdoor weather proof conditions having IP66 ingress protection. Transparent toughened glass having impact resistance protection of IK08. The luminaire shall have system wattage not exceeding 40W and system lumen output of not less than 3250 lumens, Beam angle should be 10x60 /15x45/25 Degree/As per site condition, The fixture shall have input voltage of 24V DC, provided with external high efficiency Driver operating on 240V AC, Power factor >0.90 @ full Load, internal Surge protection 4KV and other protections including OCP, OVP, SCP, OTP shall be provided in the driver. Luminaire complying to BIS standard \"IS 10322\" ,Color Temperature : 3000K, CRI>80,, Operating Temperature : -10°C to +50°C, Operating Humidity : 10%-90%, LED Makes should be CREE, LumilLED, Osram, Nichia, Bridgelux to insure higher lumen output and brightness with SMD LED chips. The manufacturer should have internal testing equipment’s especial 2m Integrating Sphere, IPX6, IK10, Humidity Chamber. The manufacturere shall submit the LM79 & LM 80 report along with the supply of material along with the BIS certificate. Make: Make REYTEK, suncity, k-lite, dwarka casting, havells as directed by the engineer inchrage. |
| 35 | Supply of high quality Static White (3000K) Linear Wall Washer in 1000mm having precies beam angle as per design or site requirement suitable for façade lighting applications. Housing to be made of extruded Aluminium alloy with excellent heat management system to ensure proper heat dissipation and thermal stability of the luminaire. The luminaire shall have electrostatically applied polyester powder coating finish. Luminaire shall be suitable to operate in a temperature range of -10°C to 50°C, LED life should be at least 50,000 burning hours at L70 at 25°C. The lens shall be made of anti-aging & anti UV-PMMA/PC material and able to minimize hot spots to insure proper light distribution. Suitable for outdoor weather proof conditions having IP66 ingress protection. Transparent toughened glass having impact resistance protection of IK08. The luminaire shall have system wattage not exceeding 24W and system lumen output of not less than 1950 lumens, Beam angle should be 10x60 /15x45/25 Degree/As per site condition, The fixture shall have input voltage of 24V DC, provided with external high efficiency Driver operating on 240V AC, Power factor >0.90 @ full Load, internal Surge protection 4KV and other protections including OCP, OVP, SCP, OTP shall be provided in the driver. Luminaire complying to BIS standard \"IS 10322\" ,Color Temperature : 3000K, CRI>80,, Operating Temperature : -10°C to +50°C, Operating Humidity : 10%-90%, LED Makes should be CREE, LumilLED, Osram, Nichia, Bridgelux to insure higher lumen output and brightness with SMD LED chips. The manufacturer should have internal testing equipment’s especial 2m Integrating Sphere, IPX6, IK10, Humidity Chamber. The manufacturere shall submit the LM79 & LM 80 report along with the supply of material along with the BIS certificate. Make REYTEK, suncity, k-lite, dwarka casting, havells as directed by the engineer inchrage. |
| 36 | Supply of high quality Static White (3000K) Linear Wall Washer in 1000mm having precies beam angle as per design or site requirement suitable for façade lighting applications. Housing to be made of extruded Aluminium alloy with excellent heat management system to ensure proper heat dissipation and thermal stability of the luminaire. The luminaire shall have electrostatically applied polyester powder coating finish. Luminaire shall be suitable to operate in a temperature range of -10°C to 50°C, LED life should be at least 50,000 burning hours at L70 at 25°C. The lens shall be made of anti-aging & anti UV-PMMA/PC material and able to minimize hot spots to insure proper light distribution. Suitable for outdoor weather proof conditions having IP66 ingress protection. Transparent toughened glass having impact resistance protection of IK08. The luminaire shall have system wattage not exceeding 15W and system lumen output of not less than 1180lumens, Beam angle should be 10x60 /15x45/25 Degree/As per site condition, The fixture shall have input voltage of 24V DC, provided with external high efficiency Driver operating on 240V AC, Power factor >0.90 @ full Load, internal Surge protection 4KV and other protections including OCP, OVP, SCP, OTP shall be provided in the driver. Luminaire complying to BIS standard \"IS 10322\" ,Color Temperature : 3000K, CRI>80,, Operating Temperature : -10°C to +50°C, Operating Humidity : 10%-90%, LED Makes should be CREE, LumilLED, Osram, Nichia, Bridgelux to insure higher lumen output and brightness with SMD LED chips. The manufacturer should have internal testing equipment’s especial 2m Integrating Sphere, IPX6, IK10, Humidity Chamber. The manufacturere shall submit the LM79 & LM 80 report along with the supply of material along with the BIS certificate. Make REYTEK, suncity, k-lite, dwarka casting, havells as directed by the engineer inchrage. |
| 37 | Supply of high quality Static White (3000K) Floodlight projector having precies beam angle as per design or site requirement suitable for façade lighting applications. Housing to be made of pressure die-cast Aluminium with excellent heat management system to ensure proper heat dissipation and thermal stability of the luminaire. The luminaire shall have electrostatically applied polyester powder coating finish. Luminaire shall be suitable to operate in a temperature range of -10°C to 50°C, LED life should be at least 50,000 burning hours at L70 at 25°C. The lens shall be made of anti-aging & anti UV-PMMA/PC material and able to minimize hot spots & insure proper light distribution. Suitable for outdoor weather proof conditions having IP66 ingress protection. Transparent toughened glass having impact resistance protection of IK08. The luminaire shall have system wattage 40W and system lumen output of not less than 3320 lumens, Beam angle should be narrow : 15/25/40 Degree/As per site condition, The fixture shall have input voltage of 240V AC, provided with internal high efficiency Driver operating on 240V AC, Power factor >0.90 @ Full Load, internal Surge protection 4KV and other protections including OCP, OVP, SCP, OTP shall be provided in the driver complying to BIS standard \"IS 10322 ,Color Temperature : 3000K CRI > 70, Operating Temperature : -10°C to +50°C, Operating Humidity : 10%-90%, LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia, Bridgelux to insure higher lumen output and brightness with SMD/COB LED chips. The successful bidder shall submit the product data sheets, LM80 report issued by LED manufacturer along with the BIS certificate.-Make REYTEK, suncity, k-lite, dwarka casting, havells as directed by the engineer inchrage. |
| 38 | Supply of high quality Static White (3000K) Floodlight projector having precies beam angle as per design or site requirement suitable for façade lighting applications. Housing to be made of pressure die-cast Aluminium with excellent heat management system to ensure proper heat dissipation and thermal stability of the luminaire. The luminaire shall have electrostatically applied polyester powder coating finish. Luminaire shall be suitable to operate in a temperature range of -10°C to 50°C, LED life should be at least 50,000 burning hours at L70 at 25°C. The lens shall be made of anti-aging & anti UV-PMMA/PC material and able to minimize hot spots & insure proper light distribution. Suitable for outdoor weather proof conditions having IP66 ingress protection. Transparent toughened glass having impact resistance protection of IK08. The luminaire shall have system wattage 24W and system lumen output of not less than 1950 lumens, Beam angle should be narrow : 15/25/40 Degree/As per site condition, The fixture shall have input voltage of 240V AC, provided with internal high efficiency Driver operating on 240V AC, Power factor >0.90 @ Full Load, internal Surge protection 4KV and other protections including OCP, OVP, SCP, OTP shall be provided in the driver complying to BIS standard \"IS 10322 ,Color Temperature : 3000K CRI > 70, Operating Temperature : -10°C to +50°C, Operating Humidity : 10%-90%, LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia, Bridgelux to insure higher lumen output and brightness with SMD/COB LED chips. The successful bidder shall submit the product data sheets, LM80 report issued by LED manufacturer along with the BIS certificate. Make REYTEK, suncity, k-lite, dwarka casting, havells as directed by the engineer inchrage. |
| 39 | Supply of high quality Static White (3000K) Floodlight projector having precies beam angle as per design or site requirement suitable for façade lighting applications. Housing to be made of pressure die-cast Aluminium with excellent heat management system to ensure proper heat dissipation and thermal stability of the luminaire. The luminaire shall have electrostatically applied polyester powder coating finish. Luminaire shall be suitable to operate in a temperature range of -10°C to 50°C, LED life should be at least 50,000 burning hours at L70 at 25°C. The lens shall be made of anti-aging & anti UV-PMMA/PC material and able to minimize hot spots & insure proper light distribution. Suitable for outdoor weather proof conditions having IP66 ingress protection. Transparent toughened glass having impact resistance protection of IK08. The luminaire shall have system wattage 12W and system lumen output of not less than 1550 lumens, Beam angle should be narrow : 15/25/40 Degree/As per site condition, The fixture shall have input voltage of 240V AC, provided with internal high efficiency Driver operating on 240V AC, Power factor >0.90 @ Full Load, internal Surge protection 4KV and other protections including OCP, OVP, SCP, OTP shall be provided in the driver complying to BIS standard \"IS 10322 ,Color Temperature : 3000K CRI > 70, Operating Temperature : -10°C to +50°C, Operating Humidity : 10%-90%, LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia, Bridgelux to insure higher lumen output and brightness with SMD/COB LED chips. The successful bidder shall submit the product data sheets, LM80 report issued by LED manufacturer along with the BIS certificate.Make REYTEK, suncity, k-lite, dwarka casting, havells as directed by the engineer inchrage. |
| 40 | Supply of Static white 3000K Neon Flex with diffused and homogenous light suitable for outdoor applications of Façade Lighting. Silicon extrusion Flexible tubes with side bending option. Silicon extrusion technology having advanced process, with high-efficiency production capacity and environmentally-friendly characteristics. Additionally, withhigh grade appearance, soft bend flexibility, strong impact resistant and high weather resistance. Uniform, dot-free and smooth lighting performance up to 5M. On field cuttable and assembly, with endcap sealed by gluing process. Power Consumption should be between 10~14W/m and have atleast 120 Led\"s per meter with 120° beam angle. Ingress Protection should be IP 67. and IK rating IK07. Size 10mm x20mm side bend. Dimmable available with PWM signal. Operating Temperature: -10°C to 45°C. The fixture shall have input voltage for 24V DC, with external high efficiency driver having power factor >0.90, Surge protection 4KV and other protections including OCP, OVP, SCP, OTP shall be provided. The lumen maintenance L70@ 25 °C of the LED shall not be less than 70% of the initial lumen after 30,000 burning hours, with suitable aluminium mounting profile.* Power supply: DC 24V * Operating Temperature range: -10°C to +45°C * LED make: CREE/ OSRAM/ LUMILED/ SEOUL/ NICHIA/Sanan/Epistar Make REYTEK, suncity, k-lite, dwarka casting, havells as directed by the engineer inchrage. |
| 41 | Supplyof decorative post top LED luminaire is designed with a robust die-cast aluminium housing and a clear injection moulded polycarbonate diffuser,ensuring long life and durability against outdoor environmental conditions. It features an ingress protection rating of IP65 and an impact resistance of IK08, making it both dust-tight and resistant to heavy impacts. The luminaire is aesthetically designed with an overall diameter of 460 mm and a height of 785 mm, and it is suitable for mounting on a Ø 60 mm pole pipe. Top cover made of spun aluminium with decorative knob on top made of die cast aluminium as shown in the drawing for unique and better aesthetics. The luminaire should have effective Heatsink for thermal management for longer life of the LEDs. The luminaire shall be provided with Type V optics to provide uniform photometric distribution suitable for typical 360 degree illumination and facilitate minimum glare, with degree of protection as IP65 Lamp Compartment. The design of the fixture has to be the same aesthetics as shown in the drawing. The system AC wattage of the luminaire shall be 45W (± 10%) with MCPCB of not less than 1.6 mm thickness and Cu of 35 microns and 2.5 thermal conductivity for fixture. Colour temperature (CCT) of 3000K, colour rendering index CRI >/= 70 and residual flux of 70% (L70) @ 50,000 hours at Ta of 25°C. The luminaire shall be suitable for operating within temperature range from - 10°C to + 45°C. The LED used should be high power LEDs (Make- Osram/bridgelux/nichia/cree/Lumiled) with Macadam |
| 42 | Charges for installation testing and commissioning of all light fixtures of poles and compund lights of Kelbai temple. Please Enable Macros to View BoQ information |
