|
| 1 | Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area & stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift Upto 1.50 M.) By Mechanical Means SSR Pg No./It No. 131/714/21.02/BDA1 Spec. No. : Bd A.1 Page No. 259 |
| 2 | Excavation for foundation in hard murum including removing the excavated material up to a distance of 50 m. beyond the building area & stacking and spreading as directed dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete ( Lift Upto 1.5 m) By Mechanical Means. SSR Pg No./It No. 113/718/21.06/BDA2 Spec. No. : Bd A. 2 Page No. 259 |
| 3 | Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting etc. complete. SSR Pg No./It No. 113/718/21.38/BDA2 Spec. No. : Bd A. 2 Page No. 259 |
| 4 | Providing and laying Casting in situ,/ Ready mix concrete cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, Steel Centering ,formwork, laying / pumping, compacting,roughening them if special finish is to be provided,finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer / concrete Batch mix plant (Pan mixer) etc. complete. With fine aggrigate ( Crushed sand VSI Grade finally washed etc.) SSR Pg No./It No. 150/820/24.01/BDE1 Spec. No. Bd. E. 1 Page No. 287 |
| 5 | Providing and laying in situ/ Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. work in foundationslike raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, formwork, cover blocks compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) complete, With fully automatic micro processor based PLC with SCADA enabled reversible drum type concrete mixer / concrete Batch mix plant (Pan mixer) etc. complete. With fine aggrigate ( Crushed Sand VSI Grade finally washed etc ) SSR Pg No./It No.153/829/25.11/BDF3 Spec. No. Bd. F. 3 Page No. 298 and B-7 Page No. 38 |
| 6 | Providing and casting in situ / Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawing or as directed including centering, formwork, cover blocks compacting and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement).With fully automatic micro processor based PLC with SCADA enabled reversible drum type concrete mixer / concrete Batch mix plant (Pan mixer) etc. complete.With fine aggrigate ( Crushed Sand VSI Grade finally washed etc ) SSR Pg No./It No.154/834/25.31/BDF5 Spec. No.:Bd. F. 5 Page No. 300 and B-7\"Page No.38 |
| 7 | Providing & casting in situ / Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs & drawings or as directed including centering, formwork, cover blocks compaction & roughening the surface if special finish is to be provided & curing complete. (Excluding reinforcement). With fully automatic micro processor based PLC with SCADA enabled reversible drum type concrete mixer / concrete Batch mix plant (Pan mixer) etc. complete. With fine aggrigate ( Crushed Sand VSI Grade finally washed etc ) SSR Pg No./It No.155/839/25.50/BDF6 Spec. No. : Bd.F.6Page No.300 and B-7, Page No. 38 |
| 8 | Providing and fixing in position TMT-FE-500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams, columns, canopies, staircase, newels, chajjas, lintels, pardis, copings, fins, arches etc. as per detailed desings, drawings and schedules including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. SSR Pg No./It No. 161/864/26.33/BDF17 Spec. No. : Bd.F.17, Page No. 306 |
| 9 | Providing second class Burnt Brick masonry with conventional/I.S. type bricks in cement mortar 1:6 in foundations and plinth of inner walls/in plinth external walls including bailing out water, striking joints on unexposed faces, racking out joints on exposed faces and watering, Complete. SSR Pg No./It No.167/882/27.01/BDG1 Spec. No. Bd.G.1 Page No. 313 |
| 10 | Providing second class Burnt Brick masonry with conventional/I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, racking out joints, watering and scaffolding etc Complete. SSR Pg No./It No.167/885/27.05/BDG5 Spec. No. Bd.G.5 Page No. 315 |
| 11 | Filling in plinth and floors with contractor’s material / brought from out side and approved by engineer incharge in layer of 15 cm to 20 cm including watering and compaction. Etc complete. SSR Pg No./It No.134/744/21.37/BDA11 Spec. No. Bd. A 11 Page No. 263 |
| 12 | Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1 kg per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete. SSR Pg No./It No. 177/956/32.11/BDL7 Spec. No. : Bd.L.7 Page No. 369 |
| 13 | Providing and laying machine cut machine polished machine cut Kota stone slabs 20 to 25 mm thick for treads and risers of steps and staircases, with rounded nosing for the treads on a bed of 1:4 cement mortar including cement float, filling joints with neat cement slurry, curing, polishing and cleaning etc. complete. SSR Pg No./It No.181/998/33.18/BDM22B Spec.No.Bd.M.22B Page No.390 |
| 14 | Providing and laying vitrified matt fininsh tiles of having size 590 mm to 605 mm x to 605 mm of 8 to 10 mm thickness and confirming IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement morar including neat cement float, filling joints, curing and cleaning complete .a) flooring. SSR Pg No./It No.183/1022/33.42/BDM12 Spec. No.: Bd.M. 12 Page No. 385 |
| 15 | Providing and fixing heavy duty inter locking concrete RUBBER MOULD GLOSSY PAVING BLOCKS of 60 millimeter thickness of having a strength of 400 Kilogram/sq.m of approved quality and shape on a bed of crushed sand of 25 to 30 millimeter thick including striking joints and cleaning etc. complete. (using 100% crushed sand) SSR Pg No./It No. 186/1031/33.53/BDM Spec. No. As Directed By Engineer Incharge |
| 16 | Providing and laying telephone black / Amba White / Cadburybrown / Ruby red / Ocean Brown granite stone of 18 to 20 mm thick for door frame/ dado/ window boxing etc. On C.M. 1:6 including filling joints with polymer base filler nosing the sharp edges wherever necessary, curing, etc. complete. SSR Pg No./It No.186/1045/33.68/BDM Spec.No.As Directed By Engineer Incharge |
| 17 | Providing and constructing granite kitchen platform with fixing of stainless steel sink 600 mm x 450 mm size as per detailed drawing including vertical both side polished kadappah stone 25 to 30 mm thick supports with kadappah top 35 to 40 mm thick and polished granite 16 to 20 mm top with side strips of granite at front and both sides of platform raised with two vertical granite supports 15 cm height and top granite of 75 x 40 cm including cutting, opening for sink of required size in kadappah as well as granite etc. complete. (Platform top size 5.00 m x 0.60 m and height is 0.75 m)SSR Pg No./It No.186/1045/41.78/BDM Spec.No.As Directed By Engineer Incharge |
| 18 | Providing and fixing solid core flush door shutter commercial in single leaf 32mm thick without ventilator commercial type of exterior grade as per detailed drawings with wrought iron hold fast, stainless steel fixtures and fastenings and handles on both sides and finishing with oil painting 3 coats complete. SSR Pg No./It No.206/1195/39.10/BDT36 Spec.No.BDT-36 Page No.500 |
| 19 | Providing and fixing fiber glass reinforced polyster door shutter 30 mm thick as per IS 14856 (2000) (Reaffirmed 2006) without ventilator including chromium plated fixtures and fastening with chromium plated handles on both sides, etc complete SSR Pg No./It No.187/1245/39.58/BDT Spec. As Directed By Engineer Incharge |
| 20 | Providing and fixing in position. (as per I.S.1868 / 1982) Aluminium sliding window of two tracks with rectangular pipe having overall dimension 63.50 x 38.10 x 1.02 mm at weight 0.547 Kilogram/One Running Metre. and window frame bottom track section 61.85 x 31.75 x 1.20 mm at weight 0.695 Kilogram/One Running Metre. Top and side track section 61.85 x 31.75 x 1.30 mm at weight 0.659 Kilogram/One Running Metre. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 Kilogram/One Running Metre. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 Kilogram/One Running Metre. And handle section 40 x 18 x 1.25 mm at weight 0.417 Kilogram/One Running Metre. and top section 40 x 18 x 1.25 mm at weight 0.417 Kilogram/Running metre. As per detailed drawings and as directed by Engineer in charge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass with all required screws and nuts etc, complete. With colour Anodising with box. SSR Pg No./It No.211/1230/39.37/BDT Spec. As directed by Engineer In Charge |
| 21 | Providing and fixing rolling shutter fabricated from steel laths of minimum thickness 0.9 mm with lock plate of 3.15 mm thickness reinforced with 35 x 35 x 5 mm angle section fitted with sliding bolts and handles for both sides, deep M.S. channel section of depth and thickness not less than 65 mm and 3.15 mm respectively with hold fast arrangements, M.S. Bracket plate 300 x 300 x 3.15 mm minimum size and shape with square bar, suspension shaft of minimum 32 mm diameter, hood cover of M.S. sheet not less than 0.9 mm thickness and of any size at top and safety devices including mechanical gear operation arrangement consisting of worm gear wheels and worms of high grade cast iron or mild steel and one coat of red lead primer etc. complete. (I.S. 62481979) (With mechanical gear) SSR Pg No./It No.215/1257/39.26/BDT Spec.No. As directed by Engineer in charge |
| 22 | Supplying and fixing of 6mm thick Exterior Compact Laminate or High Pressure Laminate of approved colour by approving authority with UV resistant Decorative colour paper on both side typically made out of multiple layers of craft papers and then impregnated with thermosetting phenolic resins, on top of it melamine treated barrier paper and decorative paper and wear layer on both the sides saturated with melamine resins and then covered with UV resistant acrylic resin layer which makes it extremely durable and weather resistant compressed together on extremely high pressure and hardened with electron beam curing to get the total desired thickness of 6mm matching European standard specification as per EN 438 -part 6, protected with 60 Micron protective peel-off film on both side which in no case leave any adhesive mark over the panel surface after it is peeled off. Fixing of the same to be done on a supporting frame of 50 mm X 5 mm X 3 mm powder coated aluminium box section to be spaced horizontally and vertically in 600mm X 600mm grid and fixed to building structure as per design through 50mmX50mmX mm 5 mm MS angle bracket prefixed to masonry slab or columns with Hilti make anchor fastener along with all related hardware and fixtures. The panel should then be fixed on the Aluminium section with the help of pure polyester exterior grade colour coating rivets as per architectural drawings or as directed by Engineer-in-charge. Each panel should be riveted on substructure maintaining a gap of 6mm on all the sides between each Panel for Air circulation and expansion and contraction as per installation specifications provided by the manufacturer. The cost shall include all expenses related to storage, material handling, lifting, freight, labour, scaffolding etc as directed by Engineer-in-charge. (Prior permission of S.E. is necessary before inclusion of this item in estimate) SSR 51.236 |
| 23 | Supply, fixing and installation of 4mm thick Cnc cutting ms jail 4mm thick with powder coating. The fixing of panel to be done with the help of VHB tapes and screws and all the sealing of joints to be done with weather sealent Silicon as directed by Engineer-in-charge. |
| 24 | Providing structural steel work in trusses, other similar trussed purlins and members with all bracing, gusset plates etc. as per detailed designs and drawings or as directed including cutting, fabricating, hoisting, erecting fixing in position, Making riveted/ bolted/ welded connection and one coat of anticorrosive paint and over it 2 coats of oil painting approved quality and shade etc. complete.SSR Pg No./It No./1181/23.04/BDR Spec. No. As Directed By Engineer Incharge. |
| 25 | Providing and fixing colour coated Zincalume ( R ) AZ150 ( min 150 gms/sq.mt. total on each side ) profiled sheets for roofing. The feed material is manufactured out of nominal 0.45 mm Base Metal Thickness ( BMT ) (0.5 mm TCT ), Hi-strength steel with min.550 MPa yield strength, metallic hot dip coated with Aluminium-Zinc alloy (55% aluminium 43.4% zinc 1.6% silicon) with COLORBOND ( R ) steel quality super durable polyester paint coat ( with inorganic pigment). The paint shall have a total coating thickness of nominal 35 um, comprising of nominal 25 um exterior coat on top surface and nominal 10 um reverse coat on back surface. Profile sheet shall have nom. 950-1050 mm effective cover width and nominal 25-30 mm deep ribs with subtle square fluting in the five pan at nominal 180-250 mm center- to-center. The end rib shall be designed for anti-capillary groove. and return leg. The feed material should have coil manufacturers product details marked a regular interval. Including fasteners with min. fastened with min. 25 um Zinc-Tin alloy coated, Hex head, self-drilling screw etc. complete. (weight of profile 4.52 Kilogram/Square Metre) SSR Pg No./It No./1181/38.34/BDR Spec. No. As Directed By Engineer Incharge. |
| 26 | Providing and fixing coloured glazed earthenware Wash Hand Basin of 55cm x 40 cm size including cold water pillar tap/cold and hot water pillar tap brackets, rubber plugs and brass chain, stop tap and necessary pipe connection including P.V.C. waste pipe and trap up to the outside face of the wall. SSR Pg No./It No. 227/1354/41.66/BDV30 Spec. : No. Bd.V.30 Page No.565 |
| 27 | Providing and fixing 15 mm dia screw down bib/stop tap of brass including nessesary sockets, union nuts complete. SSR P.No.225/1328/41.40/BDV8 Spec.No.BdV 8 Page No. 554 |
| 28 | Providing and fixing 450mm x 550mm size superior type Belgium mirror with 16mm dia. nickel plated towel rod etc. complete. SSR P.No.230/1385/42.20/BDV Spec.No.BdV 9 Page No. 555 |
| 29 | Providing and fixing 10cm PVC Nahani Trap With greating etc. complete. SSR P.No.235/1432/42.67/BDV32 Spec.As directed by Engineer Incharges |
| 30 | Providing and fixing on Walls/Ceiling/Floor 25mm Dia CPVC pipe with necessacery fittings,remaking good the demolished portion etc. complete. Including removing existing pipe line if necessacery and conveying and stacking the same in PWD chowaky or as directed etc.complet . SSR Pg No./It No. 234/1422/42.57/BDV5 Spec. As Directed By-In-Charge |
| 31 | Providing and fixing H.D.P. container syntex or alike one piece moulded water tank made out of high density polythyler and built corrugated inclusive of delivery up to destination hoisting fixing of accessories such as inlet, outlet, overflow inclusive of all taxes Capacity between 200 To1000 lit. SSR P.No.233/1418/42.53/BDV Spec.As directed by engineer in charge |
| 32 | Providing and applying Plastic Emulsion paint of approved quality ,colour and shade to old & new surfaces in two coats including scaffolding, preparing the surfaces (excluding the primer coat.) complete. SSR Pg No./It No. 192/1100/36.12/BDP6 Spec. No. : Bd. P. 6 Page No. 414 & Pre Approval Of Superitendering Engineer |
| 33 | Providing and applying pearl/ luster finish paint of approved colour and shade to the existing plaster surface including scaffolding, preparing the surface, applying the acrylic wall putti etc. complete. SSR Pg No./It 190/1086/35.23/BDO Spec.No.:As Directed by Engineer- In Charge |
| 34 | Providing & Fixing Table top 12mm thick ply & 15 mm thk. glass,embosed in table at top & All Vertical members are in 18mm thick ply . Drawers are Made in 12mm thick ply, edges of 20 mm thk., front side with frosted glass, ply work finished in laminate 1.5 mm thk. From outer side & inner side with 0.8 mm laminate with approved shade as per detailed drawing & design, with S.S. hardware like hinges, legs, finishing the wood work with polishing & 3 coats of painting wherever necessary etc. complete. RA |
| 35 | Supplying and fixing Chairs for external seating arrangements made of materials as directed by engineer in charge |
| 36 | Supplying and fixing Cafeteria Tables for external seating arrangements made of materials as directed by engineer in charge |
| 37 | Providing, Supplying and fixing electrical fittings such as switches, Fans, lights, cables etc as directed by engineer in charge |
| 38 | Providing and fixing board displaying information, such as \"Name of work, Tender cost, Name of Contractor, Work completion and liability period etc\", having rectangular shape of 1.20m x 0.90m size made out 18 gauge (1.25mm) thick mild steel sheet painted with one coat of Zinc chromate stoving primer and two coats of enamel paint on front side and grey stove enamel on back side and border / messages / symbols etc. with approved colour shade paint complete, on M.S.angle of size 35 x 35 x 3 mm frame with properly cross braced M.S. angles of size 35mmx35mmx3mm duly painted including Two M.S. angle iron posts of size 65 mm x 65 mm x 6 mm, 3.65 m long painted with alternate black and white bands of 25 cm width including all fixtures etc.and fixing the boards in 1:4:8 concrete block of size 60 cm x 60 cm x 75 cm including, excavation, refilling, transportation, and labour etc complete. Spec. No. As directed by Engineer in Charge SSR Pg No./It No.54/288/6.36/MORTH801 Spec. No. :MORTH801 |
| 39 | ADD FOR SAND ROYALTY CHARGES |
| 40 | ADD FOR OTHER MINERALS ROYALTY CHARGES |
| 41 | Test of Concrete - Compressive Strength OF C.C. M10,C20 Cube (Set of 3 cubes) SSR Pg No./It No.483/19 |
| 42 | Test of Steel 6mm,8mm,10mm,12mm,16mm dia -Tensile strength , %, Elongation, Yield Stress, Weight -Per Meter, Bend/ Rebend Test, Proof Stress. SSR Pg No./It No. 485/77 |
| 43 | GST Charges Please Enable Macros to View BoQ information |
