|
| 1 | Demolition of cement concrete ofany description and positionandremoving off debrises outside defence land premises complete all as specified and directed. |
| 2 | Dismantling floor tiling, hearth, stone slab or wall tiling including cement mortar bedding, removing srviceable tiles to store andremoving off debrises outside defence land premises complete all as specified and directed. |
| 3 | Taking down Chowkats or frame with shutter (without taking off shutter from frame)exceeding 1.5 sqm but n.exc4sqm each complete all as specified and directed. |
| 4 | Taking down Chowkats or frame with shutter (without taking off shutter from fram)not exceeding 1.5 sqm each complete all as specified and directed. |
| 5 | Taking down cement plaster on walls etc, including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. |
| 6 | Dismantling plain or corrugated steel sheeting, AC Sheets any guage, thickness including Nainital or similar pattern roof covering/wall cladding complete all as specified and directed.((Note : height of the bldg truss is upto upto 7 Metre) |
| 7 | Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including snap grid of any type and cover fillets complete all as specified and directed |
| 8 | Demolition of brick work or stone masonry built in cement mortar including pillar etc. complete all as apecified |
| 9 | Demolition of lime concrete / Mud phuska / PCC of any description and in any position not otherwise specifically provided forincluding taking down old APP membrane and removal of demolished material beyond the Md land to a distance exceeding 500mtr not exceeding 1.5KM completed all as specified and directed. |
| 10 | Dismantling timber scantlings 40 sq. cm and over in section, in any position completed all as specified and directed. |
| 11 | Dismantling timber scantlings in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm and over in section, in any position completed all as specified and directed. |
| 12 | Dismantling boarding, any description fixed in any position with nails including cover fillets and frame, complete all as specified and directed. |
| 13 | Cutting grooves in brick/stone wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 completed all as specified and directed. |
| 14 | M&L PCC 1:3:6 type C-2, 75 mm thick using 40 mm graded aggregate as in sub base/Plinth protection and path completed all as specified and directed. |
| 15 | M&L for 25mm thick Cement concrete type B-0, 1:2:4 (12.5mm graded aggregate) as in leveling/beding under floor finishes and peding concrete for roof etc all as specified and directed |
| 16 | M&L forvitrified Ceramic coloured tiles 8 to10 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.72 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles including 15mm thick screed bed in cement morar 1:6 complete all as specified and as directed by Engineer -in-Charge. |
| 17 | M&L for coloured vitrified Ceramic tiles 8 to 10 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.72 sqm, in verticle surface as in skirting/dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles including 10mm thick backing coat in CM 1:4completed all as specified and directed. |
| 18 | M&L chequered cement concrete tiles 30 cm x 30 cm x 25 mm thick, set jointed and pointed in neat cement slurry with grey cement and pigments, completed all as specified and directed. |
| 19 | M&L for Screed bed or bedding layer of mortar 20mm thick for laying floor finishes in CM 1:6 completed all as specified and directed. |
| 20 | M&L glazed ceramic coloured tiles 450x 300x 6 to 7mm thick on vertical surfaces such as dados,wall etc set and jointed in neat cement slurry and pointed in white or coloured cement to match on vertical surfaces completed all as specified and directed. |
| 21 | M&L Rendering 10 mm thick in CM (1:4) finished rough finished to receive wall tiles. |
| 22 | M&L PCC 1:2:4 type B1 (using 20 mm graded stone aggregate) as in cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, coving, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, watertroughs and the like including weathering, slightly rounded or chamfered angles andthroating, as directedincluding formed work complete all as specifed and directed. |
| 23 | S&F 2nd class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed completed all as specified and directed. |
| 24 | M&L for35mm thick flush shutter,solid core construction with block board core and plywood face panels,commercials type on both sides completed all as specified and directed. |
| 25 | M&L Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M S Square tube, supplying and fixing in opening as per manufacturers instructions all as directed completed all as specified and directed. |
| 26 | Factory made solid panel laminated PVC door shutter 30mm thick (style) consisting of frame made out M.S tube for top & bottom rails.M.S Frame shall be covered with heat moulded plain colour PVC \"C\" channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail : Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/scaled the stiles & rails with suitalble PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specifications & drawing complete all as specified |
| 27 | S&F 100 mm long butt hinges extruded aluminium alloy withgalvanisedmild steel hinge pin anodised andfixed completed all as specified and directed. |
| 28 | S/F 150mm size aluminium anodised handles, fabricated type completed all as specified and directed. |
| 29 | S/F 150mm long aluminium anodised barrel tower bolt of extruded section completed all as specified and directed. |
| 30 | S&F 150 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy completed all as specified and directed. |
| 31 | S&F 250 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed completed all as specified and directed. |
| 32 | S&F 140mm long floor door stopper of aluminum alloy body and tongue anodised with hard drawn steel spring fixed in floor or bottom of door completed all as specified and directed. |
| 33 | Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead /double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge (A) Area not exceeding 2.00 sqm eachcompleted all as specified and directed. |
| 34 | S&Fpowder coated aluminium door shutters, aluminium section weighing not less than 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified |
| 35 | S&F Powder coated aluminium sections (minimum thickness of powder coating 50 micron) work for windows/ventilators frame/ track for sliding/fixed window and shutter sections/ partitions sections with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including locking arrangemnet, cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainlesssteel screws, complete all as directed by Engr-in-Charge |
| 36 | S&F Anodised aluminium powder coatedwindow and ventilator shutters, fixed type without sash bar, aluminium section weighing not less than 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified |
| 37 | Sheet glass, 4.80 mm ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane omplete all as directed |
| 38 | S&F Aluminium composite panel 5mm to 6mm thick for aluminium doors/partitionconsisting of LDPE Core and coating with Polyvinylidene Fluoride |
| 39 | S/F Stainless Steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with Stainless Steel wire staples along with frame work of windows / ventilators with all necessary arrangementscomplete all as specified and as directed. |
| 40 | M&L for 18/19 mm thick,Prelaminated particle board (WMP), exterior grade,prelaminated both side with decorative choice lamination,fixed with screws to timber frame work,with roller in top and bottom to shutter complete all as specified and directed by Engineer-in-Charge. |
| 41 | S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roofovering/cladding to wall, fixed with self tapping screws as specified |
| 42 | S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge. |
| 43 | Excavating in post holes (or similar holes) in hard/dense soil each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, |
| 44 | M & L for PCC (1:3:6) type C2( using 40mm graded agg) as infoundation, filling and mass concrete etc. |
| 45 | Cutting holes in stone walls built in cement mortar or cement lime mortar and walls of cement concrete etc. Superficial area exc 150 Sqcm but not exc 400 Sqcm each all as specified and directed |
| 46 | M&L Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 |
| 47 | M&L for rolled mild steel sections of grade Fe-290,(Gde E-165) as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and tubular section fixed vertically and guides for sliding doors; fixed with angle cleats or other connecting plates etc complete all as specified as directed. |
| 48 | Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel withconnecting clips cross the intermediate channel at 457 mm centre to centre completed all as specified and directed. |
| 49 | Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified |
| 50 | S&F PVC laminated designed (one side PVC lamination and other side Alumnium paper) gypsum board600 x 600 x8mm thick decorative type fixed in aluminium/GI frame work with screws or nails etc complete all as specified and directed. |
| 51 | M&L 40mm thick PCC (1:2:4) type B0 using 12.5mm graded stone aggregate as in padding concrete (levelling course) on roof complete all as specified and as directed. |
| 52 | M&L for rendering 10mm thick in CM (1:3) on concrete surfaces of roof padding with integral water profing compound @3% by weight of cement content (water proofing compound to be paid separately) finished even and smooth without using extra cement complete all as specified and directed.Note: Water proofing compound will be measured and paid separately. |
| 53 | Supply only Integral water proofing compound |
| 54 | M&L for APP based polymeric membrane minimum weighing 3.5kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) including 10cm side over lap and 15cm end lap laid over primed surface by torching method all as specified and directed.The roof treatement consisting of as under :-(i) Applying one coat of bituminous primer conforming toIS 3384 applied @ 0.30 Ltr/Sqm.(ii) Laying of APP based memberane as specifiedf thickness and weight.(iii) Applying coats of Solar reflective Bituminous aluminium paint @ 0.1 Kg/ Sqm over the membrane |
| 55 | M&L Brick work with Fly ash modular bricks straight or curved on plan to any radius in half brick thick walls built in cm 1:4 complete all as apecified |
| 56 | M&L for rendering 15 mm thick on brick or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement all as specified |
| 57 | M&L for rendering 10 mm thick on brick or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement all as specified |
| 58 | Raking out joints/ pointing to brick work in walls or to random rubble orpolygonal rubble uncoursed or brought up to courses bult in Cement mortar |
| 59 | Flush pointing to random or polygonal rubble, uncoursed or brought upto course in CM 1:4 |
| 60 | M&L for preparation of old decorated surfacesof walls and cornices, spoiled by smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots by scraping and applying one coat of oil emulsion distemper, complete all as specified and directed by Engr-in-Charge. |
| 61 | M&L for applying two coats of OBD over 3mm thick wall care putty over a coat of alkali resistant primer including preparing the new plastered wall surfaces complete all as directed |
| 62 | M & L for preparation of new surfaces and applying two or more coats of 100% Premium acrylic emulsion (weather proof) paint having VOC less than 100 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over wall surfaces complete,all as specified and as directed by Engr-in-Charge. |
| 63 | M & L for preparation of old surfaces by complete removal of existing treatment of painted wall/ceiling incl pillar etc.and applying two or more coats of 100% Premium acrylic emulsion (weather proof) paint having VOC less than 100 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over wall surfaces complete,all as specified and as directed by Engr-in-Charge. |
| 64 | M&L for two coat of Synthetic enamel paint over a coat Zinc chrome primer, including Preparing new steel surfaces any description, over 10 cm width or grith,not otherwise described. |
| 65 | M&L for two coats of synthetic enamel paint over a coat of pink primer including preparation of new wooden surface of any description over 10 cm width and girth. |
| 66 | M&L 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or fix to wall all as specified and directed |
| 67 | S&F Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall. |
| 68 | Disconnecting existing tanks, setting side(or lowering if required) for repairs, cleaning, etc and hoisting if required reconnecting and re-fixing in position. exc 500 Ltrs but n .exc 1000 Ltrs capacity including cleaning and removing all scale and dirt. |
| 69 | S & F in repairs, vitreous china wash down water closet pan ( Pedestal pattern) including \"P\" or \"S\"trap with necessary fixing arrangement includingplasticwaterclosetseat coverwhitewithrecessedbottom andcoverfixed with aluminium hinging device complete all as apecified anddirected |
| 70 | S&F in repairs, PVC low level flushing cistern 10 litres capacitycomplete all as specified |
| 71 | S&Fin repairs, counter top vitreous china wash basin white flat back size 550x400mm with brackets including cutting for and pinning in ends of brackets or erecting stand including waste coupling CP brass 32mm dia with long screwed shanks & fly nuts & fancy type CP pillar tap complete all as apecified |
| 72 | S&F Grating doom 100mm dia of PTMT (Minimum weight 25gms) |
| 73 | S&F PVC (SWR) multi floor trap with grating including jointing with solvent cement |
| 74 | M&L Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete |
| 75 | S&F in repairs 600x450mm bevelled edge mirror of selected quality glass, mounted on 06mm thick commercial ply wood backing including aluminiumframe and fixed in wall with wooden plug with chromium plated brass screws and cup washerswith glass self assembly complete all as specified and as directed by Engineer-in-Charge. |
| 76 | S&Fin repairssoap dish, vitreous china white, approximate size 160 x 160 x 90mm, fixed to plugs with chromium plated brass screws all as specified and as directed. |
| 77 | S&F in repair Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe), complete all as specified and as directed by Engineer-in-Charge. |
| 78 | S&F Concussive push button taps of cast copper alloy, screwed for 15mm iron pipe and fixed all as specified and directed. |
| 79 | S&F push button type urinal spreader cast copper alloy for fixing with 15 mm dia pipe all as specified and directed. |
| 80 | S&F CP brass tubular towel rail 600mm long 20mm dia \"D\" type in repairs complete all as specified |
| 81 | S&F in repairs for low density polythelyne pipes (LDPE) of pressure rating 6kgf/cm2 fixed complete to wall or in floors etc. as in outlet pipe for WHB etc. 32mm bore complete all as specified |
| 82 | Taking up or down steel tubing & connections,15 mm dia complete all as apecified |
| 83 | Taking up or down steel tubing & connections,20 mm dia complete all asapecified |
| 84 | Taking up or down steel tubing & connections,50 mm dia complete all asapecified |
| 85 | S & F 15mm dia. Unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe all as specifiedanddirected. |
| 86 | S & F 20mm dia.Unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe |
| 87 | S & F 50mm dia.Unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe |
| 88 | Cutting chases ,pinning in making good to facing where required of stone walls and pointed in cement mortar 1:3 for concealed water tubing etc cutting not exc 10 cm girth. |
| 89 | Cutting holes in stone walls built in cement mortar or cement lime mortar and walls of cement concrete etc. Superficial area exc 150 Sqcm but not exc 400 Sqcm each all as specified and directed |
| 90 | S&F 1mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 all as specified and directed. |
| 91 | S&F in repairs 15mm bib taps fancy type chromium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferule and fixed |
| 92 | S&F in repairs,CP 15mm, stop valves/ angle cock, fancy type cast copper alloy with crutch or butterfly handle, screwed down, high pressure, screwed both ends for iron pipe complete all as specified |
| 93 | S&F 15 mm dia 600 mmlong PVC water connection with PTMT nuts and washersall as specified |
| 94 | S&F in repairs 15mm bore Fancy type pillar taps, long shank (swan neck), Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed. |
| 95 | S & F Gun metal globe or gate valves of 20 mm dia with iron wheel head screwed both ends for iron pipe and fixed in repair complete all as specified |
| 96 | S&F in repairs 20 mm bore dia ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (min weight 210gms) complete all as specified |
| 97 | S&F 100mm aluminium barrel tower bolts, stove enamelled black, with bright bolt and fixed. |
| 98 | S&F 50 mm long Magnet ball catcher made out of PVC fixed to shutter and chowkhats with SS screw all as specified and directed by Engr-in-Charge. |
| 99 | M&L for ATT at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same |
| 100 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custodyor for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc all as specified. |
| 101 | Taking down the existing unserviceable main switch / cut out / DBs of any type / capacity / description as per existing at site including making good the disturbed surfaces to match with the existing finishes all as specified. |
| 102 | Material and labour for point wiring complete all as specified with 1100 Volts grade 1.5 Sqmm PVC insulated FR-LSH unsheathed cable with multistranded copper conductor conforming to IS:694:1990 with ISI marking in and including PVC rigid conduit medium grade of size minimum 20 mm with all accessories concealed in wall / ceiling including cutting chases andcontinous earth wire 1.5 Sqmm PVC insulated FR-LSH unsheathed 1100 Volts multistranded copper conductor connected to common earth and earth dolly including Concealed modular metal flush boxes in walls and modular white plate covers with frame for mounting of modular switches/sockets/fan regulators etc and making good the disturbed surface to match with existing complete all as specified and directed by E-IN-Charge for the following:- (a) One light point controlled by one, one way switch 6 A, SP |
| 103 | (b)One ceiling fan/exhaust fan point controlled by one, one way switch |
| 104 | (c)One 3 point 6 Amps switch socket outlet point controlled by one switch on the same board. |
| 105 | (d)One 3 pin 6 Amps switch socket outlet point controlled by one switch on independent board. |
| 106 | Description all as per item No 3 here-in-before but using 4.0 Sq mm single core copper conductor cable of multistranded PVC FRLSH insulated unsheathed 1100 Volts grade for 6/16 Amps switch socket combination point including running of 4.0 Sq mm copper conductor PVC FRLSH wire as earth continuity conductor along with wiring and connecting to the common earth dolly. |
| 107 | S&F modular switch 1way 6A, 1 module all as specified and directed |
| 108 | S&F modular switch 1way 16A, 1 module all as specified and directed |
| 109 | S&F modular socket, 6A - 2/3 pin combined 2 module, flush tpe all as specified and directed |
| 110 | S&F modular socket, 6A/16A - 2/3 pin combined 2 module, flush tpe all as specified and directed |
| 111 | S & F ceiling rose three terminal surface bakelite type AC 50 Hz 230 Volts of size 65 x 50 mm complete all as specified. |
| 112 | S&F modular metal flush box 6 module all as specified and directed |
| 113 | All as per item No.109 hereinbefore but 4 moudle |
| 114 | All as per item No.109 hereinbefore but 3 moudle |
| 115 | All as per item No.109 hereinbefore but 2 moudle |
| 116 | S & F modular white cover plate with frame 6 module all as specified and directed |
| 117 | All as per item No.113 hereinbefore but 4 moudle |
| 118 | All as per item No.113 hereinbefore but 3 moudle |
| 119 | All as per item No.113 hereinbefore but 2 moudle |
| 120 | S&F of Lamp holder, metal cased, bakelite body, 230 volts, complete all as specified and directed. |
| 121 | S&F LED lamp 9W complete all as specified and directed by the Engineer-in-Charge. |
| 122 | Supply & replacement of 20 W ( minimum 120 lumem / watt) surface / wall mounted LED batten having PC diffuser, CRI>80, PF>0.9, CCT 6500K, independent isolated SMPS pased constant current electronic LED driver with THD<20%, surge voltage protection and other safety tests as per IS15885 (Part-2/Sec-13): 2012, with rated life 50,000 burning hours, system efficiency/ lumens 120 lumen per watt and housing made up of aluminium, white coloured ABS end caps, IP 20 protection, input voltage range 140- 270 V, input freqency 50-60 Hz, including electrical connection with3 core flexible Cu conductor cable of appropriate size from ceiling rose to the fixture complete all as specified and directed.Note: Contractor shall submitTDS ( Technical Data Sheet) alongwith sample approvalMake: Havells/ Philips/ WIPRO/ Crompton. |
| 123 | Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with potted Electronic driver, including Aluminium housing connecting up with three core flexible copper conductor cable of suitable size complete. Make: Havells/ Philips/ Wipro/Crompton. |
| 124 | Supply and Fixing ofLED luminaire 600mm X 600mm 35/36W ,220V, AC recessed type with high efficiiency PMMA diffuser soft glare free light complete with drivers ,holders LED lamp suitable for roof ceiling connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. Make: Havells/ Philips/ Wipro/Crompton.. |
| 125 | S&F modular fan step regulator, 2 module all as specified and directed. |
| 126 | Supply and fixing ceiling fans completewith blades, down rods, electronic regulator/Remots and accessories, white color, 230 V, 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor(BLDC). Note : - Old Fan deposit in MES store yard.Make: Havells/Orient/USHA/Crompton |
| 127 | Supply & fixWall mounted fans AC single phase 230/ 240 V, of size 400 mm sweep, metal body, three blade with fixing arrangement including making of hole to the wall and making good the disturbed surface complete. Make: Havells/Crompton/USHA/ STANDARD/ Bajaj. |
| 128 | M & L for Submain wiring with two single core 10 Sq mm PVC FRLSH insulated unsheathed copper conductor multistranded 1100 Volts grade drawn in and including concealed rigid PVC conduit of suitable dia, conduit fittings and accessories concealed in wall including cutting & chases with one run of 10 sqmm PVC FRLSH insulated unsheathed copper conductor cable as earth continuity conductor along the wiring and connected to the common earth dolly complete including removing the existing unserviceable sub main wiring and making good the disturbed surface to match with the existing all as specified. Note 1: Two runs of 10 Sqmm cable, one run of 10 Sqmm earth contuinity conductor and one run of conduit shall bemeasured and paid as one unit length length including qutade rate. |
| 129 | M & L for Submain wiring with two single core 6 Sq mm PVC FRLSH insulated unsheathed copper conductor multistranded 1100 Volts grade drawn in and including concealed rigid PVC conduit of suitable dia, conduit fittings and accessories concealed in wall including cutting & chases with one run of 6 sqmm PVC FRLSH insulated unsheathed copper conductor cable as earth continuity conductor along the wiring and connected to the common earth dolly complete including removing the existing unserviceable sub main wiring and making good the disturbed surface to match with the existing all as specified. Note 1: Two runs of 6 Sqmm cable, one run of 6 Sqmm earth contuinity conductor and one run of conduit shall bemeasured and paid as one unit length length including qutade rate. |
| 130 | Supply and fixing sheet Metal enclosure double door type for DB’s 240 Volts Single Pole and Neutral 8 way with 200 Amps rated bus bar complete all as specified andas directed.Make: ABB/ Legrand/ Havells. |
| 131 | Supply and fixing sheet Metal enclosure double door type for Vertical TPN DB for 125 Amp MCCB as incommer, 8 way with 200 Amps rated bus bar complete all as specified andas directed. Make: ABB/ Legrand/Havells. |
| 132 | S&F MCCB 415 Volt 16/18 KA 4 pole 125 Amp thermal magnetic trip release & setting ICU= 100% ICS as incoming with fixing arrangement complete all as specified and directed. Make: ABB/ Legrand/C&S. |
| 133 | Supply and fixing MCB SPN 40Amps , 240 volt, 10 KA,complete all as specified andas directed. Make: Havells/ ABB/ Legrand. |
| 134 | Supply and fixing MCB SPN 32 Amps , 240 volt, 10 KA,complete all as specified andas directed. Make: Havells/ ABB/Legrand. |
| 135 | Supply and fixing MCB single pole 6 to 32 Amps, 240 volts, 10 KA complete all as specified and as directed by the Engineer-in-Charge. Make: Havells/ABB/ Legrand. |
| 136 | S&Fin replacement of air ventilation fan Plastic (PVC) body Type 250 mm , ,single phase,250V AC including making necessary hole by breaking existing wall to fix air ventilation fan,with frame fixing holdfastner, bolt,washer etc including connection with twisted white three core flexible copper multistranded conductor cable from ceiling rose to connector all a directed by Engineer-in-charge. Old Ex fan shall be deposited to MES store yard. MAKE:Havells/ STANDARD/Crompton. |
| 137 | M&Lfor Cutting chases on stone wall suitable for 20to 25 mm PVC conduit pipeandmaking good distube surfacewhere required and including cement work with cement mortar 1:3:2 complete maching with good distube surface as directed by Eng-in-Charge. |
| 138 | Supply and fixing Energy saving and environmental friendly long life 35W LED bldg security light made up of pressure die cast aluminium housing with high efficiency LED as lighting source and lens embedded PC cover having bottom opening seperate driver compartment with IP66 protection and impact resistance of IK08, potted Elect driver with surg protection complete with all accessories incl three run of 1.5 Sqmm Copper conductor cable from security light to ceiling rose complete.Make : Havells/ Wipro/Crompton. |
| 139 | Supply and fixing GI pipe bracket made of 40 mm bore light grade pipe made to shape of overall length of 1.2 mtr for fixing of security light fittingincluding MS clamps , nuts & bolts of required size complete |
| 140 | Supply and layon wall/in ground/on pole ISI marked XLPE insulated armoured, heavy duty, electric cable with aluminium conductors 1100 volts laid in trenches, floors, ducts, pipes drawn across the road/paths/drain/along poles/walls/floor/equivalent etc including jointing & testing complete all as specified of size 50 Sqmm , 3.5 core all as specified and directed. ( Main panel to VTPN DB ) Make: Havells/KEI/Polycab/Gloster |
| 141 | Excavation in trenches not exceeding 1.5 mtr width and not exc 1.5 mtr in depth and getting out in hard /dense soil for laying / repairing of LT cable / GI pipe. |
| 142 | Supply, spread river sand of approvalin cable trenches providing for cable cushioning as directed.NOTE :- Punned thickness of sand only will be measured and paid. |
| 143 | Removal of surplus soil to a distance not exc50 mtrs away and depositingwhere directed at a level not exc 1.5 mtr above the starting point. |
| 144 | Returning , filling incl spreading levelling watering and well rammingin layers not exc 25 cm thick. |
| 145 | Supply and lay PCC cable covers for LT cable protection, Class LV, Type 1 of size 250x150x40mm |
| 146 | Supply and fixing medium grade GI tubing of 50 mm dia for XLPE cable protection complete all as specified and as directed |
| 147 | Earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick burried directly in ground to a depth not less than 2.25 m below ground level with top edge of earth plate not less than 1.5 m below normal ground level connected to GIearth wire 4 mm dia drawn through and including GI protection pipe of light grade 15 mmbore by means of bolts, nuts, checknuts and washers all as shown in Electrical Plate No.3 of SSR Part-I and connected to main switch board including excavation and earth work, PCC chamber in 1:3:6, RCC Cover in 1:2:4 type B-1 reinforced with8 mm dia MS bars at 10 cm c/c, 20 mm dia medium grade GI pipe with funnel and wire mesh complete and watering arrangement all as specified. (Note: GI pipe 15mm dia, GI wire 4mm dia upto 7.5m deemed to be included in quoted rate.) |
