|
| 1 | Dismantling AC corrugated, semi corrugated sheets in roof covering, complete all as specified and as directed by Engineer-In-Charge. |
| 2 | Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including any pattern roof coverings, complete all specified and directed. |
| 3 | Dismantling of mild steel work of any description, complete all specified and directed. |
| 4 | S&F pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified & directed, complete all specified and directed. |
| 5 | S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall,fixed with self tapping screws ,complete all specified and directed. |
| 6 | S&F on asbestos ceiling board of 4mm thick, designer, in ceiling fixed as per manufacturer’s instructions, including powder coated galvanised iron snap grid frame work of main and tee (weight not less than 240gm/Rm), angle (weight not less than 217 gm/Rm), grid size 595x595mm, for false ceiling all as specified, and hangers not less than 3mm nominal dia, galvanised iron (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of galvanised iron wire of 2.0mm dia, length as required at site and expansion hold fasteners 12.50mm dia, 40mm long including dismantlingof wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets,complete all specified and directed. |
| 7 | S&F rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, confirming to grade Fe 410-W (Gde E-250 quality-A), complete all as specified and directed. |
| 8 | Dismantling of brickwork or stone/ boulder masonry, built in cement mortar including allquoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and as directed. |
| 9 | M&L for brick work with sub class \"B\" bricks old size straight or curved in plane exc 6m mean radius built in cement mortar 1:6, complete all as specified anddirected. |
| 10 | All as per above but except brick. |
| 11 | Taking down cement plaster on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed. |
| 12 | M&L for rendering 10 mm thick in cement mortar 1:6 on any surfaces of brick work, finished even & smooth without using extra cement, complete all specified and directed. |
| 13 | M&L for rendering 15 mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces, finished even & smooth without using extra cement,complete all specified and directed. |
| 14 | M&L for preparation of newly plastered surface of wall applying two coats of distemper oil emulsion over one coat of alkali resistant primer over two coats of wall care putty, complete all as specified and as directed . |
| 15 | M&L for preparation of new plastered or unplastered surfaces of walls and applying two coats of cement based paint over a coat of alkalie resistant priming paint , complete all as specified and as directed. |
| 16 | M&L for complete removal of existing treatment from old plastered or unplastered surfaces of walls and applying two coats of distemper oil emulsion over one coat of alkali resistant primer over two coats of wall care putty, complete all as specified and as directed. |
| 17 | M&L for complete removal of existing treatment from old decorated surfaces of wall and applying two coats of cement base paint, complete all as specified and as directed. |
| 18 | M&L for preparation of old surface of walls, applying two coats of Emulsion paint (Apex Ultima or Equivalent) over one coat of alkali resistant primer including complete removal of exiting treatment , complete all as specified and as directed . |
| 19 | M&L for preparation of old surface of ceiling and applying two coat of white(Lime) washing, including complete removal of existing treatment, complete all as specified and as directed . |
| 20 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and as directed. |
| 21 | M&L for 25 mm thick plain cement concrete 1:2:4 type B-1 using 20 mm graded crushed stone aggregates finishing concrete surface even and fair without using extra cement including necessary formwork, complete all as specified and as directed. |
| 22 | S&F non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of eachtile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, including screed bed or bedding layer of mortar 15mm thickin cement mortar 1:6, complete all as specified and directed. |
| 23 | M&L for non-skid, coloured, ceramic tiles of size 600 x 600 mm 7 to 8mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match and laid over and including screed bed or bedding layer of mortar 15mm thick in cement mortar 1:6, complete all as specified and directed. |
| 24 | M & L for non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) suitable size to match existing floor tiles 7 to 8 mm mm thick, as in skirting set and jointed in neat cement slurry (3 Kg cement per Sqm) and pointed in white or coloured cement to match shade of tiles over 10 mm thick rendering in cement mortar 1:4on other than fair faces of brick work, complete all specified and directed. |
| 25 | M&L for machine cut kota stone slab, minimum size shall be (550x550mm), flooring 18-20 mm thick laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing with beeswax polish (mirror finish) complete, over and including screed bed or bedding layer of mortar 20mm thick in cement morat 1:3, complete all as specified and as directed. |
| 26 | M&L for machine cut kota stone slab, (size shall in one length), 18-20mm thick, as in riser of steps, skirting, dado and pillar, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete, and including laid over screed bed or back plastering layer of mortar 15mm thick in cement mortar 1:4, complete all as specified and as directed by Engineer-In-Charge. |
| 27 | M&L for makrana white marble work (table rubbed and polished), 18-20mm thick, as in steps, jambs, pillars, window-cills, cooking platforms and like with 20mm thick screed bed in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of marble, complete all as specified and as directed by Engineer-In-Charge. |
| 28 | M&L for glazed ceramic jointless tiles in vertical surface/dado, size 450x300x6/7 mm thick, on vertical surface of wall such asskirting, dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade/colour of tiles including 10mm thick rendering in cement mortar 1:4, complete all as specified and as directed. |
| 29 | M&L for granite (of any type) 16-18 mm work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite over and over 20 mm thick screed bed in cement mortar 1:3, complete all as specified and as directed. |
| 30 | Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level), complete all as specified and directed. |
| 31 | M&L for 75mm thick, plain cement concrete M-10 1:3:6, type C-1 (using 20mm graded crushed stone aggregate),as in plinth protection and providing the joints throughout the thickness, filled with mastic filling comprising bitumen 85/25 grade and sand mixture 1:3 by weight, complete all specified and directed. |
| 32 | Taking down chowkhat or frame with shutters (without taking off shutters from frames) exc. 1.5 Sqm but n.exc 4Sqm each, complete all as specified and directed. |
| 33 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 Sqm each, complete all as specified and directed. |
| 34 | M&L pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., size of frame 125x60mm, complete all as specified and as directed . |
| 35 | M&L for pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., size of frame 105x60mm, complete all as specified and as directed. |
| 36 | S&F factory made steel window, box type, using ERW hollow \"P\" section, comprising double frame for and including gauged and glazed skeleton shutter with wire mesh and plain sheet 4mm thick glass, jointed internally and made with flat iron 40x4mm complete including grill/ guard bars of 8mm square bars fixed horizontally @100mm C/C including mild steel hinges, handles, tower bolts, stops, lugs etc, complete all as specified and as shown in drawing No- CEUZ/TD-1517/15, sheet No- 1/3 to 3/3 and as directed . Note :- Cost of window shall include all members and spare parts as elaborated in the Drwaing and in the specifications and nothing shall be paid extra seperately. |
| 37 | S&F anodised aluminium powder coated (minimum thickness of powder coating 50micron) frame forwindow, ventilator with one or more rebates including joining cleat for fixing etc, complete all as specified and as directed. |
| 38 | S&F 5.0 mm frosted sheet glass, ordinary quality fixed in windows in square n exc 0.5 Sqm in each pane fixed in aluminium partion, complete all as specified and as directed . |
| 39 | S&F 40 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides with both faces covered with decorative face veneer with lipping/frame to match complete all as specifed and directed. |
| 40 | S&F 40 mm thick flush shutter prepared to receive glass/ wire cloth, etc. (in 2 panels n. exc 0.4 sqm each) with sash bars, solid core construction, with block board core and plywood face panels, commercial type on both sides with both faces covered with decorative face veneer with lipping/frame , includingstainless steel wire cloth, 0.46mm nominal dia of wire and average width of aperture 1.18mmetc.; supplied and fitted to chowkhats, complete all as specified and as directed . |
| 41 | S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet rein forced with M.S. square tube supplying and fixing in opening as per specification and drawing, complete all as specified and directed. |
| 42 | S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat molded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail lock rail and bottom rail and as gap insert for top rail and bottom rail paneling of plain colour PVC sheet to be fitted in the MS frame welded etc. with suitable PVC sheet beading including hinges etc, complete all as specified and directed. |
| 43 | M&L for mild steel framed work such as in grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; staging for of water tanks, cooler stand and similar work conforming to Fe-290, Gde-E-165, including cutting and welding and taking down existing steel.complete all as specified and as directed |
| 44 | S&F TMT bars of 5mm dia and over upto and including 10mm dia in stirrups,spacers and binders and binding with and including mild steel wire (annealed) not less than 0.9 mm dia.,complete all as specified and as directed. |
| 45 | S&F TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia.,complete all as specified and as directed. |
| 46 | M&L for formwork to flat finished surface of concrete to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, chajja, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and as directed. |
| 47 | M&L for reinforcement cement concrete (nominal mix) type B-1 ,1:2:4 (20 mm graded crushed stone aggregatge) for Chajjas/Balcony/Landing work/kitchen slab etc, complete all as specified and as directed. |
| 48 | Dismantling of old/ damaged existing roof treatment and plastering 10mm thick on fair faces of concrete surfaces, in cement mortar 1:4, including mixing water proofing compound @3% by weight in cement, rendering is to be finished even and and smooth (without using extra cement) when the concrete is green, complete all as specified and as directed.NOTE:- Cost of water proofing chemical shall be included in quoted rate. |
| 49 | M&L for water proofing treatment on roof top with APP (Ataxic poly proplene) modified polymeric five layered membrane with central core of 100 micron high molecular high density polyethylene film, minimum weight not less than 3.0 Kg/Sqm 2.0mm thick, centre core is sandwiched on both sides by high quality polymeric mix with properties of high softening point, high heat resistance and cold resistivity to make it ideal for all water proofing treatment, with polymeric mix protection on both sides with 20 micron HMHDPE film, laid over one coat of bituminous primer conforming to IS:702, applied @ 0.40 Kg/Sqm and one coat of hot blown bitumen of 85/25 grade, conforming to IS:3384, applied @1:20 Kg/Sqm on prepared surfaces of roof, overlap should be not less than 150mm at ends and 75mm at sides, joints and overlaps uniformly bounded with LPG torch flame including applying of one coat of semi bot blown bitumen of 85/25 grade @1.20 Kg/Sqm and fine screened sand in dry condition @0.50 Kg/Sqm after laying the membrane and applying two coats of aluminium paint,complete all as specified and as directed. |
| 50 | S&F in repair curtain rod, 20 mm dia stainless steel fixed with brakets,stops,rollers etc, complete all as specified and as directed. |
| 51 | M&L for applying two coats of synthetic enamel paint over a coat of zinc chrome/red oxideprimer including preparation of new or previously untreated steel surfaces over 10 cm in width or girth, complete all as specified and as directed. |
| 52 | M&L for preparation of old painted steel surfaces of any description, not otherwise described, over 10cm width or girth including and applying one coat (finishing coat) of synthetic enamel paint, complete all as specified and as directed. |
| 53 | S&F extruded aluminum alloy handles 150mm ISI marked size fabricated type anodized, complete all as specified and as directed. |
| 54 | S&F aluminium anodised barrel tower bolt ISI marked of extruded section and fixed, length of bolt 200mm, complete all as specified and directed. |
| 55 | S&F aluminium alloy, anodised, sliding door bolt, size 300mm, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy,ISI marked, complete all as specified and as directed. |
| 56 | S&F mild steel spring for doors, 300mm, ordinary rat tail rod pattern springs including roller and roller plate, ISI marked, complete all as specified and as directed. |
| 57 | S&F floor door stopper 140mm overall length of cover plate of aluminium alloy body and tongue,anodised,with hard drawn steel spring, ISI marked fixed in bottom body of door, complete all as specified and directed. |
| 58 | M&L for 75 mm thick plain cement concrete 1:4:8, type D-2 using 40mm graded crushed stone aggregates as in sub bases of floors and pavings, complete all as specified and as directed. |
| 59 | M&L for machine pressed precast concrete interlocking paver block of any size and shape confirming to IS 15658-2006 of 60mm thickness M-35 grade with grey cement and no pigment including 25mm thick sand cushioning,complete all as specified and directed |
| 60 | M&L for 25mm thick sand filling under floor or in foundations or in floor including watering and consolidation, complete all as specified and directed |
| 61 | Providing and laying at or near ground level factory made kerb stone of M-25 (Design mix) grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required ,complete all as specified and as directed . |
| 62 | M&L for plain cement concrete 1:3:6 type C-0 (using 12.5 mm graded crushed stone aggregate) as in filling of pressed steel frame, complete all as specified and directed |
| 63 | S&F in repair vitreous china urinal, half stall and grating and union for discharge pipe (excluding flushing cistern and flush pipe but including waste pipe), complete and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing flush pipe, grating and union for discharge pipe fixing in repair, complete all as specified and as directed. |
| 64 | S&F sinks made of stainless steel 0.80mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm fixing in repairs, complete all as specified and as directed by Engineer-In-Charge. |
| 65 | S&F vitreous china wash basin, white, flat back, size 550x400mm excludings taps, waste, chain and plugand porcelain stopper including brackets of any size, including cutting for and pinning in ends of brackets or erecting stand including fixing and supply of waste pipe of 32 mm dia, waste coupling of PTMT (half or full threaded) and pedestal, fixing in repairs, complete all as specified and as directed. |
| 66 | Pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered \"Hot\" or \"Cold\" with long screwed shanks and fly-nuts, screwed for iron pipe and fixed for 15mm bore pipe, fixed in repair, complete all as specified and as directed. |
| 67 | S&F vitreous China squatting pattern Orissa pattern WC size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe) but excluding lime concrete bedding, complete all as specified and as directed. |
| 68 | S&F Vitreous China wash down water closet pan (pedestal pattern), white (including fixing bolts, flush pipe but excluding flushing cistern) and including plastic water closet seat cover, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device and making good to dismantled/ damaged floor in cement concrete M-15 (1:2:4), type B-1 (using 20mm graded crushed stone aggregates), complete all as specified and as directed . |
| 69 | S&F in repair 600x450mm bevelled edge mirror of selected quality glass mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup waste washer, complete all as specified and directed. |
| 70 | S&F in repair PVC valveless symphonic action type flushing cistern, low level, white with inlet ball valve, float and handle including brackets 10 ltr capacity, complete all as specified and directed. |
| 71 | S&F in repair waste pipe for SINK/WHB/Urinal for 32/40mm dia, complete all as specified & as directed. |
| 72 | S&F in repair angle valves, cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed for 15mm bore pipe, complete all as specified and as directed. |
| 73 | S&F in repair PVC connection 15mm bore size with PTMT nuts of length 45cm length, complete all as specified and directed. |
| 74 | S&F in repair 110 mm PVC (SWR) floor/Nahani trap, plain with grating including jointing with solvent cement, complete all as specified and as directed. |
| 75 | S&F in repair PVC (SWR) \"P\" or\"S\" trap of 110mm dia outlet, including jointing with solvent cement, complete all as specified and as directed. |
| 76 | S&F in repair stainlees steel grating, chromium plated, size 125/150mm, with or without hole heavy duty, complete all as specified and as directed. |
| 77 | S&F in repair 15 mm bore CP bib taps (long body), fancy type chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and, complete all as specified and as directed. |
| 78 | S&F in repair bib taps chromium plated fancy type, cast copper alloy with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed 15mm bore, complete all as specified anddirected. |
| 79 | S&F in repair chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union, complete all as specified and as directed. |
| 80 | S&F in repair stainless steel soap dish, chromium plated, any type, fixed to plugs with screws, complete all as specified and as directed. |
| 81 | S&F in repair stainless steel towel rail chromium plated 20mm dia \"D\" type 60 cm long between flanges, ISI marked, complete all as specified and as directed. |
| 82 | S&F in repair 15mm bore angle valve brass chromium plated screwed down, high pressure with crutch or butterfly handle concealed type with long shank cup,complete all as specified and as directed. |
| 83 | S&F in repair health faucet mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and wall hook including making connections and fixed in position, complete all as specified and as directed. |
| 84 | S&F in repair rotational moulded polyethylene water storage tanks of 1000 litres capacity, (cylindrical vertical tanks with closed top) (White in colour and three layered) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc. including float valve 20/25mm, complete all as specified and as directed.Note: Old storage tank shall be deposited at store yard of MES and shall be property of department. |
| 85 | Taking up or down steel tubing of 15mm bore pipe and connections, including cleaning for re-fixing or removal to store, complete all as specified and as directed. |
| 86 | S&F tubes, \"medium grade\" galvanised, 15mm bore, ISI markedwith all fitting such as bends, tees, elbows, unions, short pieces, connectors, back nuts, etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed.Note: Cost of cutting/ chasing for pipe line making concealed in surfaces shall be deemed included in quoted rates. |
| 87 | Taking up or down steel tubing of 25mm bore pipe and connections, including cleaning for re-fixing or removal to store, complete all as specified and as directed. |
| 88 | S&F tubes, \"medium grade\" galvanised, 25mm bore, ISI markedwith all fitting such as bends, tees, elbows, unions, short pieces, connectors, back nuts, etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed.Note: Cost of cutting/ chasing for pipe line making concealed in surfaces shall be deemed included in quoted rates. |
| 89 | S&F in repair PVC (SWR) bends of 110mm bore, pressure capacity not less than 4.50 Kgf/Sqcm, any radius, fixing with adhesive, complete all as specified and as directed. |
| 90 | S&F in repair PVC (SWR) pipes, 110mm bore, pressure capacity not less than 4.50 Kgf/Sqcm, single socketed, in any length with rubber ring joints, laid in trenches, complete all as specified and as directed . |
| 91 | S&F in repair PVC (SWR)junction single, (single T) equal or unequal,complete all as specified and as directed. |
| 92 | S&F in repair 110 mm bore PVC (SWR) vent cowl, complete all as specified and directed. |
| 93 | S&F in repair 25 mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed high pressure with crutch or butterfly handle, complete all as specified and as directed. |
| 94 | S&F in repair glavanised Mild steel wire cloth. 0.46mm nominal dia of wire and average width of aperature 1.18mm and fixed with tinned tacks or galvnaised wire staples, complete all as specified and directed. |
| 95 | S&F rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, confirming to grade Fe 410-W (Gde E-250 quality-A), complete all as specified and directed. |
| 96 | Demolition of reinforced concrete as in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work. reinforcement cut as required to facilitate demolition,complete all specified and directed. |
| 97 | Precast reinforced cement concrete M-20 1:1.5:3, type A-1, (using 20mm graded crushed stone aggregate), nominal mix, as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs and similar articles with plain faces as specified in clause No- 4.11.16 of SSR Part-I (2009), set in cement mortar 1:4, complete all as specified and as directed by Engineer-In-Charge. |
| 98 | S&F stainless steel peg set of six with base plate and fixed to wall/door and including rawal pugs/ screw, complete all as specified and as directed. |
| 99 | M&L for glazed ceramic coloured designer pattern tiles 350x250x7mm / 450mmx 300mmx7mm thick on vertical surface such as skirting, dado etc. set and jointed in white colour cement,including rendering 10mm thick on fair faces of brick work or concrete surface in cement mortar 1:4 as backing coat for tiles including dismantling of existingwall tiling with cement mortar backing and removing, complete all as specified anddirected. |
| 100 | M&L for plaster plate of desired shape and size including writing letters or figures (Block, Roman, Italic or Indian) not exceeding 30 cm high, complete all as specified anddirected. |
| 101 | S&F for factory made, glazed and skeleton shutters in second class hardwood, 35mm thick, open rebated and prepared to receive glass, gauze, etc. (in3 panel) with sash bars, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass including galvanized mild steel wire cloth, 0.46mm nominal dia of wire and average width of aperture 1.18mmetc.; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a); supplied and fitted to chowkhats, complete all as specified and as directed by Engineer-In-Charge. |
| 102 | S&F for factory made, plain framed, paneled shutter (any number of panel) 35mm thick, 2nd class hardwood with lock rail and panel of 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS:1003 (Part-I), kiln seasoned and chemically pressure treated, complete all as specified and as directed by Engineer-In-Charge. |
| 103 | Preparation of new or previously untreated wooden surfaces of any description, not otherwise described, over 10cm width or girth including and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and as directed by Engineer-In-Charge. |
| 104 | Taking down carefully copper/aluminium point wiring ( light, fan, bell, socket or power, light fitting )complete,includingfixtures and fittings such as switches, ceiling roses, holders, regulators, sockets, tube light fittings and including making good the disturbed surfaces to match with existing surface and colour shade with putty and white cement for smooth finishing of holes,small patches etc, complete all as specified and directed. |
| 105 | M&L for point wiring for one light point/fan point/bell point controlled by one-one way switchwith 1.5 Sqmm. (nominal area) single core FRLS,PVC insulated 1100 Volts, grade multi stranded unsheathed copper conductor unsheathed in and including PVCcasing caping medium grade of 25mm width complete with all acessories including PVC sunk box ISI marked for mounting of switches, sockets, fan regulator etc with 3 mm thick plastic laminated sheet as top cover, and 1.5 Sqmm. (nominal area) single core FRLS, PVC insulated 1100 Volts, grade multi stranded unsheathed copper conductor cable as earth wire upto common earth and connected to earth dolly including making goodthe diturbed surfaces to match with the existing, compete all as specified and directed. (Note:- Three run of copper conductor of required size and one run of casing capping measured as one unit and also colour coding of wiring to be followed as red/yellow/blue for phase, black for neutral and green for earth) |
| 106 | (a) One light point/fan point/ exhaust fan point/ bell point controlled by one switch. |
| 107 | (b) One 5 pin 5 amps socket point controlled by one 6 amps switch on independent board . |
| 108 | (c) One 5 pin 5 amps socket point controlled by one 6 amps switch on same board . |
| 109 | Description all as per item No.105 above, but point wiring with 2.5 Sqmm and earth conductor of size 2.5 Sqmm complete all as specified and directed but for One 6 pin 16/6 amps socket outlet point controlled by one 16 amps switchon independent board, complete all as specified and directed. |
| 110 | S&F Switch flush type, 5 amps 240 volts single pole on way, complete all as specified and directed.Supply and fixing switch piano, flush type, single pole, one way, 6 Amps, complete all as specified and as directed by Engineer-In-Charge. |
| 111 | S&F socket outlet, flush type 2/3-pin, 6-Amps,complete all as specified and as directed. |
| 112 | Supply and fixing switch socket combination,2 in 1 ,3-pin, 5/16-Amps, flush type, complete all as specified and as directed by Engineer-In-Charge. |
| 113 | Supply and fixing including connection testing of stepped type (multi-steps) electronic regulatorfor ceiling fan 1200/1400 mm, 240 volts,including connecting, complete all as specified and as directed by Engineer-In-Charge. |
| 114 | S&F ceiling rose, three phase/ PVC/ polycarbonate, isolated body, JUMBO type, complete all as specified and as directed. |
| 115 | S&F angle lamp holder, polycarbonate insulated body with back plate including LED bulb 9 Watt, 240 Volts, complete all as specified and directed. |
| 116 | S&F LED light fitting 1x20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified and directed. |
| 117 | S&F in repair LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection, complete all as specified and directed. |
| 118 | Labour only for refixing/Hanging only ceiling fan (M.D. supply) with replacement of 3 core multistranded copper conductor cable of size23/0.193 from ceiling rose to fan ternimal including over hauling the fan, painting of ceiling fans complete with two coats synthetic enamel paint by spraying including filling in cavities with filler after cleaning all dust etc ,complete all as specified and directed. |
| 119 | S&F of exhaust fan 300 mm sweep steel body with louvers,240 volts AC single phase, 50 Hz, ISI marked, including necessary work in wall/sheet, including connection cable of suitable size, nut bolt and other fixing material, complete all as specified and directed.Note: (i) Cutting of walls/wooden panel of any description and making provision of holes etc and making good to the disturbed surface to matching with the existing finish shall also be deemed to have been included in the quoted rates. (ii) The dismantled/unserviceable exhaust fan shall be deposited with MES store yard for safe custody and shall be the property of the department. |
| 120 | Supply and fixing sheet metal enclosure DB TPN 4 way double door made powder coated out of CRCA mild steel sheet200 amps rated bus bar dust and vermin proof suitable for incorporation ofMCBs duly concealed in wall and making good to disturbed surface completeincluding dismantling existing DB, complete all as specified and directed. |
| 121 | S&F sheet metal enclosures DB\"s double door factory made power coated out ofr CRCA mild steel sheet 1.6 mm thick with metallic painting white series, 240 volts 200 amps rated enamelled bus bar 8 way dust and vermin proof proof suitable for incorporation of MCBs duly concealed in walls and making good to disturbed surface and colour matchingcomplete including dismantling existing DBs, complete all as specified and directed. |
| 122 | Supply and fixing sheet metal enclosures DB\"s double door factory made power coated out ofr CRCA mild steel sheet 1.2 mm thick with metallic painting white series, 240 volts 200 amps rated enamelled bus bar 4 way dust and vermin proof proof suitable for incorporation of MCBs duly concealed in wass and making good to disturbed surface and colour matching including dismantling of existing DBs complete all as specified and directed. |
| 123 | S&F in repair MCB SP 6 to 32 Amps 10 KA,\"C\" series, AC, 240Volts, 50Hz , ISI marked, complete all as specified and directed. |
| 124 | S&FMCB SPN 32 Amps 10 KA,\"C\" series,AC, 240Volts, 50Hz, ISI marked, complete all as specified and directed. |
| 125 | S&FMCB TPN63 Amps 10 KA,\"C\" series,AC, 415Volts, 50Hz, ISI marked, complete all as specified and directed. |
| 126 | M&L for Earthing complete with galvanised steel earth plate electrode 600mmX 600mmX 6mm thick buried directely in ground vertically ( earth pit not less than 2.25 meters deep below ground level) with top edge of plate not less than 1.5 metres belowground level, connected to and including galvanised iron wire 4 mm dia and light grade protection pipeof 15 mm diafrom earth electrode up to test point or up to 7.5mtr whichever is less by means of GIbolts, nuts, check nuts and washersall as per electrical plate No 3 of SSR Pt-I and GI watering pipe of 20 mm dia medium grade,GI funnel with wire mesh,including charcoal, salt packed all around the earth electrode plate in layers, plain cement concrete earth pit chamber 1:3:6 type C1, of size 45X 45X 45 cement mortar, RCC cover 1:2:4 type B1 of size 45X45X6 cement mortar, excavation/earth work in any strata and returning filling, removal of surplus soil and testing/test point for required value including removing old unserviceable earthing item, complete all as specified and directed. |
| 127 | S&F in repair GI bracket pipe of size 40 mm dia medium grade of 1.5 mtr long bent to shape hot or cold suitable for street light fitting and making the one end of GI pipe bracket suitable for fixing of any type street light fitting and shall be fixedon wall surfaces and including suitable fabricate MS flat ironclamps of 25X6 mm thick -02 Nos suitable for fixing any places with nuts,bolts & washers including grouting on wall etc, including taking down, complete all as specified and directed. |
| 128 | Supply and laying, connecting and testing for XLPE insulated screened PVC bedded galvanised steel strip or wire armoured UG heavy duty electric cable with aluminium conductor 1100 volts grade cross sectional area of 16 Sqmm 4 core size laid in trenches under floor/roads/hard standing along poles etc including taking down exixting cable any type and size all as specified and directed. Note: Excavation and earth work, sand cushioning, brick protection & GI pipe shall be measured and paid for separately), complete all as specified and as directed. |
| 129 | Supply and laying, connecting and testing for XLPE insulated screened PVC bedded galvanised steel strip or wire armoured UG heavy duty electric cable with aluminium conductor 1100 volts grade cross sectional area of 10 Sqmm 2 core size laid in trenches under floor/roads/hard standing along poles etc including taking down exixting cable any type and size all as specified and directed. Note: Excavation and earth work, sand cushioning, brick protection & GI pipe shall be measured and paid for separately), complete all as specified and as directed. |
| 130 | M&L for sub main wiring in repair complete with 2 run of 6.0Sqmm single core copper conductor (ISI marked)cable1100 volts grade, FRLSH type, PVC insulated, unsheathed,flexible,multi strandedcolour coded cables drawn through and including rigid PVC conduit of size 25 mm dia medium grade(MMS) with all connected accessories such asBend,Tee,Elbow,Short peices etc concealed in wall/roofs/floorsand including cutting chases and making good the surface, one run of 6 Sqmm single core copper conductor cable flexible, PVC insulated, unsheathed, multistranded, 1100 volts grade,FRLSH type as earth continuity conductor connected to common earth dolly and including making good the disturbed surfaces to match with existing surface and colour coat and applying putty including cutting and chasing and including taking down existing, complete all as specified and directed by Engr in ChargeNote : - Two run of 6 Sqmm single core copper conductor cable and one run of 6 Sqmm single core copper conductor cable as earth continuity and one run of PVC conduit shall be measured as one unit only, complete all as specified and as directed. |
| 131 | Excavation in trenches in any type of soil not exceeding 1.5 m wide and not exc. 1.5 mtr deep ,complete all as specified and directed |
| 132 | M&L clean dry river sand in trenches/ducts for cushioning to cable, 8cm in depth before laying the cable and 15cm in depth after laying the cable, complete all as specified and directed |
| 133 | M&L for brick protection to cable using old size sub class \"B\" bricks, laidflat, dry butt jointed, laid lengthwise perpendicular to the axis of cable, complete all as specified and directed. |
| 134 | Returning filling including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in trenches, complete all as specified and directed. |
| 135 | Removal of surplus soil obtained from excavation to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point, complete all as specified and directed. |
| 136 | S&F in repair for GI pipe 40 mm dia light grade fixing to wall or laying in floors for protection of cable complete existing pipe, complete all as specified and directed. |
