|
| 1 | Dismantling floor, hearth or wall tiling including cement mortar bedding(but not backing), removing serviceable tiles to store and rubbish off the premisescomplete all as specified and as directed by Engr-in-Charge |
| 2 | Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid dry or laid dry and pointedcomplete all as specified and as directed by Engr-in-Charge |
| 3 | Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any positioncomplete all as specified and as directed by Engr-in-Charge |
| 4 | Demolition of brick/block work or stone/boulder masonrybuilt in cement mortarcomplete all as specified and as directed by Engr-in-Charge |
| 5 | M & L forPrecastcement concrete block masnory with solid blocks, 1: 3: 6 using (20mm graged aggregate) set in cm 1: 6exc.10 cm in width and setting in mortar complete all as specified and as directed by Engr-in-Charge |
| 6 | Use and waste the form work to soffits of suspended slab such as roof slab, landings and similar work . (Horizontal or sloping) for fair finished surface n.exc 200 mm thick complete all as specified and as directed by Engr-in-Charge |
| 7 | Use and waste the formwork to sides of concretecomplete all as specified and as directed by Engr-in-Charge |
| 8 | M & L forRCC 1 : 2 : 4 Type B1 ( 20 MM graded aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed by Engr-in-Charge |
| 9 | S & F forTMT steel bars 6mm to 8mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking end and binding with and including MS wire annealed not less than 0.9 mm dia but in stirrups complete all as specified and as directed by Engr-in-Charge |
| 10 | S&F for Non skid ceramic coloured tiles7 to 8mm thick, (square /rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc,laid over 15mm thick screed bed in cement mortar 1:6 and set and jointed in neat cement slurry and pointed incoloured cement complete all as specified and as directed by Engr-in-Charge |
| 11 | S&Ffor glazed ceramic Coloured tilesover vertical surface of wall,350x 250x7mm / 450x350x7mm thick, set and jointed in neat cement slurry and pointed in coloured cement to match including backing coat of 10mm thick in CM(1:4) complete all as specified and as directed by Engr-in-Charge |
| 12 | M&L for machine cut kota stone slabin patch work 18-25 mm thick over cement screed base 15 mm thick in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match with the shade of slab including grinding polishing complete all asincluding grinding polishing rounding to edges complete all as specified single piece of stone on steps shall be provided |
| 13 | M&L for Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed. |
| 14 | Taking down of cement plaster fromsurfaces of wallof any description including raking out joints, hacking out for key, scrubbing down with water etc including complete treatment if any all as specified. |
| 15 | M&L for rendering 10mm thickcement plaster on concrete surfaces of walls in CM 1:6 , finished the surface even and smooth wihout using extra cement etc complete all as specified and directed. |
| 16 | M&L for rendering 5 mm thickcement plaster on concrete surfaces of ceiling in CM 1:3 , finish the surface even and smooth without using extra cement etc complete all as specified and directed. |
| 17 | M&L for preparation of new plasteredsurfaces of walls, and applying two coat of oil bound distemperover a coat of primer all as specified and directed |
| 18 | M&L for preparation ofnewplasteredof ceiling and applying three coat of white wash all as specified and as directed by Engineer in Charge. |
| 19 | M&L forfactory made 18 mm thick (+-0.7 mm) PVC celuka one side preleme and PVC celuka of density 600 Kg/Cum manufactured by an ISO 9001-2008 certified company for kitchen cabinet shutter complete as per manufatures specification and direction of Engr-in -Charge. Make :- Rajashri Brand and equevilant |
| 20 | M&L forfactory made 18 mm thick (+-0.7 mm) PVC celuka plain white colourtedof density 600 Kg/Cum manufactured by an ISO 9001-2008 certified company for kitchen cabinet shutter complete as per manufatures specification and direction of Engr-in -Charge.Make :- Rajashri Brand and equevilant |
| 21 | M&L forfactory made 12 mm thick (+-0.5 mm) PVC celuka on plain white colourted of density 600 Kg/Cum manufactured by an ISO 9001-2008 certified company for kitchen cabinet shutter complete as per manufatures specification and direction of Engr-in -Charge. Make :- Rajashri Brand and equevilant |
| 22 | M&L forfactory made 05 mm thick (+-0.2 mm) PVC celuka on plain white colourted of density 600 Kg/Cum manufactured by an ISO 9001-2008 certified company for kitchen cabinet shutter complete as per manufatures specification and direction of Engr-in -Charge.Make :- Rajashri Brand and equevilant |
| 23 | S&F fpr 75mm stainless steel handles complete all as specified and directed. |
| 24 | S&F fpr 100mm stainless steel hinges complete all as specified and directed. |
| 25 | S&F magnet typePVC door stopper 30 to 40mm dia fixed with screw behind the door all as approved by Engr -in-Charge. |
