Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Taking down cement plaster of any description and in any position of brick or stone wall/concrete surfaces on walls ,ceiling etc including raking out joints ,hacking for key scrubbing down with water etc & prepared to receive new plaster complete all as specified and directed. Note: if existing plaster found on site in multi layers, in this situation contractor will remove complete plaster,rate for the same will be included deemed in quoated rates |
| 2 | M&L for 15mm thick rendering on fair faces of brick/concrete surfaces in CM 1:4 finished even and smooth without using extra cement mixed with water proofing compound.(Note :-WPC shall be measured & paid separately) |
| 3 | M&L for rendering 5 mm thick in Cement Mortar (1:3) on ceiling finished even and smooth without using extra cement complete all as specified and directed. |
| 4 | M&L for 15 mm thick rendering on surfaces other than fair faces of brick/concrete surfacesin CM (1:6) and finished even and smooth without using extra cement complete all as specified and directed. |
| 5 | Supply only Integral waterproofing compound.complete all as specified and directed. |
| 6 | M&L for applying acrylic wall care putty on old/ new plastered internal/Externalsurfaces of walls/ceilings/soffits (thickness vary from 1.5 to 2.5 mm as required for desired smoothness and levelling of surfaces in two or more layers) by using ready made wall care putty including sand papering after filling the putty to make surface smooth and ready for receiving painting etc complete all as specified and directed.Make of wall Putty : JK wall Putty / Birla Wall care Putty / Bison Wall Putty.Notes : (i) The prepared surface after wall putty, the contractor will inform to the GE as well as to the Engineer-in-Charge for site inspection before applying further finishes. Please note that the further finishes work will start only after approval of the prepared surface from the GE. |
| 7 | Complete removal of existing treatment of any type/description from walls/RCC surfaces/ceiling/chajjas/roof projections etc with mechanical means/grinder complete all as specified and as directed. |
| 8 | M&L for preparation of surfaces and applying 02 coats of exterior emulsion paint (light shade) over new/ old surfaces with highlighter of any approved shade,@ 5 sq.m/litre/2 coats by using roller to external walls/RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc surfaces over & including a coat of exterior wall primer @ 11 sq.m/litre/1 coat as recommended for under coat by manufacturer of exterior emulsion by using following brands of emulsion and primer complete all as specified and directed.Make of Exterior Wall Primer : Asian / Berger / Nerolac [Best Quality].Make of Exterior Emulsion : Asian (APEX)/ Berger (WEATHER COAT ANTI DUST) / Nerolac (EXCEL TOTAL) . |
| 9 | M&L for preparation of surfaces and applying 02 coats of interior emulsion paint (light shade) over new/ old surfaces @ 10 sq.m/litre/2 coats by using roller/brush to wall surfaces over & including a coat of interior wall primer @ 10 sq.m/litre/1 coat as recommended for under coat by manufacturer of interior emulsion by using following brands of emulsion and primer on existing yellow coloured surface complete all as specified and directed.Make of Interior Wall Primer : Asian / Berger / Nerolac [Best Quality].Make of Interior Emulsion : Asian (tractor shyne)/ Berger (bison) / Nerolac (BEAUTY sheen) |
| 10 | M&L for preparation of surfaces and applying 02 coats of interior emulsion paint (white shade) over new/ old surfaces @ 10 sq.m/litre/2 coats to ceilings surfaces over & including a coat of interior primer @ 10 sq.m/litre/1 coat as recommended for under coat by manufacturer of interior emulsion by using following brands of emulsion and primer complete all as specified and directed.Make of Interior Wall Primer : Asian / Berger / Nerolac [Best Quality].Make of Interior Emulsion : Asian (tractor shyne)/ Berger (bison) / Nerolac (BEAUTY sheen) |
| 11 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. |
| 12 | Material and labour for Double charge vitrified coloured tiles (approved shade) of size 1200mm x 600mm having thickness 8 to 9 mm premium quality having water absorption less than 0.08%, straight edge, stain free, glossy finish, square marbonite, laid as in floor, set and jointed using type-I adhesive (thick bed fixing) confirming to IS-15477:2004 and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, complete all as specified and directed.Make : Johnson (Snow Flair/Albano White Plus/Albano Lemon Plus) or Techno commercial equivalent in make mentioned in Appendix \"B\" |
| 13 | Ditto all as above item but as in skirting, but tiles laid over and including 10 mm thick bedding layer in cement mortar (1:3) complete all as specified and as directed. |
| 14 | M&L for non skid ceramic ede cut tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:4, complete all as specified and as directed. Make : Somany/Johnson/Kajariya/Sunheart. |
| 15 | M&L for glazed ceramic tiles (coloured) 600x300x 7mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10 mm thick rendering (as screed bed) in cement & sand mortar 1:4, complete all as specified and as directed. Make : Somany/Johnson/Kajariya/Sunheart. |
| 16 | Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar complete all as specified and as directed. |
| 17 | M&L (telephone Z black) Granite slab work 18-20mm thick in floors steps, cooking platforms and likeincluding pointing in white cement with admixture of pigment to match with granite shade over & including screed bed 15mm thick in CM 1:6 including cutting recess opening for the sink portion and embedding complete all as specified and directed. complete all as specified and directed. : Note: deduction shall be made for opening of sink portion, shall deemed to be included in the quoted rate) complete all as specified and directed. |
| 18 | M&L (telephone Z black)Granite (of any type) tiles 20mm thick machine cut, in skirting/dado laid over cement screed and jointed with grey cement slurry, and pointed with whitecement with admixture of pigment to match the shade of granite stone including grinding and polishing complete laid over 10mm thick screed layer in cement mortar 1:4 complete all as specified and directed. |
| 19 | Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and othersimilar situations complete all as specified and directed. |
| 20 | M&L for preparation of old steel painted surfaces exc 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed. |
| 21 | Taking down chowkats or frame with shutters (without taking off shutters from the frame) n exc 1.5 sqm each complete all as specified and directed. |
| 22 | Taking down chowkats or frame with shutters (without taking off shutters from the frame) exc 1.5 sqm and n exc 4.0 Sqm each complete all as specified and directed. |
| 23 | Taking down shutters of any description and in any positionexceeding 1 sqm & not exceeding 2 sqm each complete all as specified and directed. |
| 24 | Taking down shutter of any description exc 1 Sqm and not exc 2 Sqm each and refixing in same opening including easing and adjusting of shutter as required including renewal of unserviceable screws all as directed. |
| 25 | Supply and fixing Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 850 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and as directed.Note: (i) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made(ii) Cost for M.S. hold fast/ lugs or SS dash fasteners shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account. |
| 26 | Supply and Fixing Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 850 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and as directed.Note: (i) WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.(ii) Cost for M.S. hold fast/ lugs or SS dash fasteners shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account. |
| 27 | Supply and Fixing Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 150 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 850 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.Note: (i) WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.(ii) Cost for M.S. hold fast/ lugs or SS dash fasteners shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account. |
| 28 | Supply and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non-toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-in-Charge including supply and fixing following items :(a) Stainless Steel (304 Grade) Finished Butt Hinges 100mm - 4 nos. per leaf(b) Stainless Steel (304 Grade) Finished Square Tower Bolt 150 mm long - 2 nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 150 mm - 2 nos. per leaf |
| 29 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk) and non-toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as per direction of Engineer- in-Charge including supply and fixing following items :(a) Stainless Steel (304 Grade) Finished Butt Hinges 100mm - 4 nos. per leaf(b) Stainless Steel (304 Grade) Finished Square Tower Bolt 200mm long - 2 nos per leaf(c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 nos. per leaf(d) Stainless Steel (304 Grade) Finished Sliding Bolt 300 mm - 1 no. per leaf(e) Stainless Steel (304 Grade) Finished Floor Door Stopper - 1 nos. per leaf |
| 30 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type Skelton door shutter of size 35 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk) and non-toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws,including S&F of stainless steel 304 Grade (natural finish) wire cloth complete all as per direction of Engineer- in-Charge including supply and fixing following items :(a) Stainless Steel (304 Grade) Finished Butt Hinges 100mm - 4 nos. per leaf(b) Stainless Steel (304 Grade) Finished Square Tower Bolt 200mm long - 2 nos per leaf(c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 nos. per leaf(d) Stainless Steel (304 Grade) Finished Sliding Bolt 300 mm - 1 no. per leaf(e) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 nos. per leaf(f) Stainless Steel (304 Grade) wire cloth fixing as per manufacture |
| 31 | M&L for providing and fixing factory made UPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+-0.2mm). Window profile with hollow section with multi chamber. Frame (108mm x 45mm), sliding sash (39mm x 65mm). Sliding mesh Sash (39mm x 58mm) Sliding interlock (One vertical length in each shutters) (45mm x 38mm), Glazing bead (20mm x 18mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (32mm x 13.5mm) 2 nos, sliding sash (33mm x 20mm), sliding mesh sash (29mm x 19mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel-304 Black coated wire cloth and required accessories. Note: The unit rate quoted by contractor excludes cost of glass & wire mesh and includes all other connected accessories. Net Opening will be measured for payment purpose. Wire mesh and Glass Shall be measured and paid Separately& Cutting holes of suitable depth in wall for inserting lugs etc including making good dismentalled portion with PCC (1:2:4) type B-0 using 12.5mm graded crushed stone aggregate and cement mortar (1:3) shall be deemed to be included Note : 1Description of items amend accordingly as per manufacturer instructions.Note : 2(i) Test certificate of manufacturer to be provided by contractor.(ii) Embossing with barcode of manufacturer engraved over each door frame and shutter is mandatory. |
| 32 | S & F factory made UPVC window or ventilator side hung/top hung (glazed and gauge both) white colour casement (Openable) window made of extruded profiles with wall thickness of 2.3mm (+-0.2mm). Window profile with hollow section with multi chamber frame (60mm x 55mm), sash (60mm x 75mm), T profile (One vertical length in between two shutters) (60mm x 74mm), Glazing bead (34mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 0.2mm thick, galvanized steel Frame (28mm x 20mm), sash (31mm x24.5mm). T profile (28mm x 20mm) to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100mm long fasteners. Hardware: [casement handle made of zinc alloyed (white powder coated). Butt Hinges of zinc alloyed (white powder coated), transmission gear made of mild steel with multi point locking system] and 5mm thick glazing with selected quality glass & Stainless steel-304 Black coated wire cloth and required accessories. Note: The unit rate quoted by contractor excludes cost of glass & wire mesh and includes all other connected accessories. Net Opening will be measured for payment purpose. Wire mesh and Glass Shall be measured and paid Seperatly. Provision of all other items & Cutting holes of suitable depth in wall for inserting lugs etc including making good dismentalled portion with PCC (1:2:4) type B-0 using 12.5mm graded crushed stone aggreegate and cement mortar (1:3) shall be deemed to be include.Note : 1Description of items amend accordingly as per manufacturer instructions.Note : 2(i) Test certificate of manufacturer to be provided by contractor.(ii) Embossing with barcode of manufacturer engraved over each door frame and shutter is mandatory. |
| 33 | M&L forPlain fillets or beading of sectional area Exc3 & n. exc 6sq.cm of 2nd class hard wood square, rectangular or triangular in section , clean sawn, se-cured with nails or brads for securing wiremesh or similar worksput together with glue pinned at joints incomplete all as specified and directed. |
| 34 | M&L block board, 19/20mm thick, grade 2 quality, interior grade, commercial type, fixed with screws to timber frame workas in cup board shutter/shelves/cabinet etc, complete, all as specified and directed. |
| 35 | M&Lfor 0.90mm thick decorative laminates \"Mica type 1 of surface finished,colour and pattern as approved, fixed with adhesive as per makers instructions complete all as specified and as directed. |
| 36 | S&F 25 mm size magnetic catches with Plastic body and striking plate including letting in and fixed complete all as specified and directed. |
| 37 | S&F continuous (piano) hinges 20mm & 12 MM width of flap, mild steel bright finish or electrogalvanised of complete all as specified fixed with CP steel screws complete all as specified and directed. |
| 38 | Supply & fixing aluminium (extruded section body) Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed (IS Marked) complete all as specified anddirected. |
| 39 | S& FStainlesssteel-304wire cloth 0.36 mm nominal dia of wire and avarage width of aparture 1.40mm and fixed including necessary beading etc. complete all as specified and directed. |
| 40 | M& L for toughned glass5 mm thick fixed in Upvc window of any size in each panescomplete all as specified and directed. |
| 41 | All as per item here-in-above but pin head type, figuredglass complete all as specified and directed. |
| 42 | S&Faluminium powder coatedventilator with fixed aluminium frame of size 65 x 40 x 1.98mm thick fixed in vertical position with aluminium vertical members andhalf portion to be provided with 4mm thick pin head glass and remaining portion to be louvered using 4mm thick pin head glass and louvered portion covered with stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm incl necessary channel frame work, including rubber gasket and aluminium beading complete all as specified and directed. |
| 43 | M &L for Framed/unframed work such as angle, grills,gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors;ladders; framedbalusters; walk ways; railings;girder ,channelframework of water tanksand similar work conforming to Fe.290.Gde-E-165etc complete all as specified and directed. |
| 44 | S&F in repairs stainless steel curtain rod 25 mm dia (minimum weight 0.36 Kg per RM) with brackets, fancy knobs and rings (20 cm c/c) etc complete all as specified and directed. |
| 45 | S&F gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of 20 mm bore,all as specified and as approved by GE. |
| 46 | S & F in repairs wall mixer 3-in-1 system with provision for both hand shower and overhead shower complete with 115 mm long bend pipe with connecting legs and wall flanges complete all as specified and directed. (MAKE -CONFIRMING TO JAQUAR CAT PART-No. STE -107281 OR EQUIVALENT) |
| 47 | Supply and fixing vitreous china premium/1st quality wall hung water closet with P trap white/ivory/off white including connection to drain (or out going pipe) and to flushing pipe, antisyphonagee pipe,etc., and incl. plastic soft close seat cover as recommended by manufacturer for particular model closed pattern with flat bottom etc; and incl S&F of all necessary accessories set like rag bolts/gel gasket/hinges etc as recommended by manufacturer for fixing, packing and taking down existing of any description/size complete all as specified and directed.Make : Jaquar (Continental Series-CNS-WHT-963N or Techno commercial equivalent in make mentioned in Appendix \"B\" |
| 48 | Supply and fixingconcealed flushing cistern of PVC 8 ltr. cap with dual flushing system, valveless syphonic action type, with inlet/outlet, ball valve, float and including brackets and connection to pipe etc. and incl S&F of all necessary accessories/installation kit and \"S\" type drain pipe connetion set for wall hung WC etc as recommended by manufacturer for fixing, packing and including S&F of actuator knob/flush plates and and taking down existing of any description/size complete in all respect all as specified.Make: Jaquar (Concealed Cistern-JCS-WHT-2400S, Flush Plate-JCP-CHR-812415) or Techno commercial equivalent in make mentioned in Appendix \"B\" |
| 49 | S&Fin repairs vitreous china water closet (squatting pan), orissa patern size 575 x 440 x 250 mm white with integral, foot rests an including \"P\" trap and lime bedding making good to floors complete all as specified and directed.(MAKE -CONFIRMING TO JAQUAR CAT PART-No. ECH-WHT-451LE OR EQUIVALENT) |
| 50 | S&F in repair 10 litre capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets with flush pipe 32mm dia complete all as specified and directed. (MAKE - CERA/PARRYWARE) |
| 51 | S & F in repair corner vitreous china wash basin, white flat back , size 450mmx300mm with and including Waste fittings, brass, chromium plated forbasins with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed with and including Supplying and fixing cast copper alloy chromium plated,fancy type,pillar tap swan neck,15mm bore,screwed down high pressure with or without lettered hot or cold with long shanks, screwed for iron pipe complete all as specified and directed.(MAKE - CERA/PARRYWARE/JAQUAR) |
| 52 | S&F sink with drainage board made of stainless steel 1mm thick for kitchen with plugs, washers and wastes, including fixing with cast iron cantilever brackets, bedding in cement mortar on to dwarf wall, connecting union to pipe, overall minimum size 915mm x 460 mm with bowl size 410mm x 330mm x160 mm including 32mm dia waste pipe of polythelene of low or high density, 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0, complete, including taking down old unserviceable sink. Make: Nirali/Neelkanth/Diamond/Jayna |
| 53 | S & F in repairs 15mm dia angle valves, Chromium plated crutch or butterfly handle screwed down high pressure, screwed both ends for iron pipes or for unions.(MAKE -CONFIRMING TO JAQUAR CAT PART-No. STE -107053 OR EQUIVALENT) |
| 54 | S & F in repairs 15mm dia 2-in-1 bib tap with angle valves, Chromium plated crutch or butterfly handle screwed down high pressure, screwed both ends for iron pipes or for unions complete all as specified and directed.(MAKE -CONFIRMING TO JAQUAR CAT PART-No. STE -107067 OR EQUIVALENT) |
| 55 | S&F in repairs 15mm bore bib tap, cast copper alloy, chromium platedwith capstan head, screwed down, screwed for iron pipe or for brass ferrule,complete all as specified & directed.Make: Jaquar/Prayag/ESSCO/Parryware |
| 56 | S&F in repairs shower rose 100 mm dia of brass chromium plated fancy type with or without swivel joint suitable for fixing to 15mm bore GI pipe complete all as specified and directed.(MAKE -CONFIRMING TO JAQUAR CAT PART-No. EOS-542N OR EQUIVALENT) |
| 57 | S&F in repair health faucet spray type jet with brass jet, chromium plated, and 1.0 m long PVC flexible pipe complete all as specified and directed.(MAKE -CONFIRMING TO JAQUAR CAT PART-No. STE -107067 OR EQUIVALENT) |
| 58 | S & F in repairs 15mm size PVC connections with PTMT nuts of length 450 mm.complete all as specified and directed. |
| 59 | M&L in repairs 40mm dia Low density poly ethylene pipes(LDPE) of pressure rating 6 Kgf/cm2fixed complete to wall, ceiling or in floors etc complete all as specified and directed. |
| 60 | S&F in repair 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 61 | S&F glass corner self assembly, fancy type,made of 5 mm thick sheet toughened glass of size 250x250mm,fixed with CP brackets,complete,all as specified and directed. |
| 62 | S&F in repairs CP brass tubular towel rail,20mm dia, ‘D’ type, 60cm long between flanges, fixed to PVC rawl plugs with chromium plated brass screws, complete all as specified and directed. |
| 63 | M&L cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth all as directed. |
| 64 | S&F for Rotational moulded polyethylene water storage tank(white) in double layer of 1000 liter capacity (cylindrical vertical with closed top incl float valve) hoisted and fixed in position all as specified and directed. |
| 65 | M&L for cutting grooves in brick wall, 75 mm wide and 65 mmdeep and shaping horizontal face of groove with cement mortar 1:3 /epoxy groutingto ends of landings, steps, cills sunshades, shelves lintels etc complete all as specified and directed. Note : Epoxy grouting applied by approved applicator |
| 66 | M&L for cutting holes or through PCC block / RCC wall built in CM and making good in CM 1:3 or cement concrete 1:2:4 type B-1 as required, superficial area exc 150 sqcm but n.exc 400 sqcm complete all as specified and directed. |
| 67 | Demolition and breaking up drain pipes (salt glazed ware, AC or Reinforced concrete) internal dia of pipe in 75mm set in cement mortar complete all as specified and directed. |
| 68 | Demolition and breaking up drain pipes (salt glazed ware, AC or Reinforced concrete) internal dia of pipe in 110mm set in cement mortar and taking out of trenches, if required complete all as specified and directed. |
| 69 | S&F for 75mm PVC (SWR) pipes single socketed,inanylength with rubber ring joints, laid in trenches or in floors complete all as specified and directed. |
| 70 | S&F for 110mm PVC (SWR) pipes single socketed,inanylength with rubber ring joints, laid in trenches or in floors complete all as specified and directed. |
| 71 | S&F 110 mm bore PVC (SWR) pipes Type B ISI marked single socketed in any length with rubber ring joints laid on wall fixedcomplete all as specified and directed |
| 72 | S&F 110mm dia PVC (SWR) branch piece Tee (Single \"T\") equal or unequal with acess door complete all as specified and directed. |
| 73 | S&F 75mm dia PVC (SWR)bendsany radius with access door complete all as specified and directed. |
| 74 | S&F 110mm dia PVC (SWR)bendsany radius with access door complete all as specified and directed. |
| 75 | S&F for PVC (SWR) floor trap long body type, plain with grating including jointing with solvent cement complete all as specified and directed. |
| 76 | S&F for PVC (SWR) vent cowl 110 mm bore complete all as specified and directed. |
| 77 | M&L PCC 1:2:4 type B1 using 12.5 mm graded aggregate as in hold fast, cill etc with necessarry form work complete all as specified and directed. |
| 78 | Taking up or down existing unserviceable upvc/ mild steel water tubing and connections 15mm dia, any grade,of any description or in any position including fittings complete all as specified and directed. |
| 79 | Taking up or down existing unserviceable upvc/ mild steel water tubing and connections 20mm dia, any grade,of any description or in any position including fittings complete all as specified and directed |
| 80 | Supplying and laying16 mm outer dia CPVC SDR 13.5 and plain CPVC SDR 11 fittings pipes fixed complete to walls, ceilings or in floors etc., any type of pipe etc in required length complete all as specified and directed |
| 81 | Supplying and laying20 mm outer dia CPVC SDR 13.5 and plain CPVC SDR 11 fittings pipes fixed complete to walls, ceilings or in floors etc., any type of pipe etc in required length complete all as specified and directed |
| 82 | Dismantling of brick tiles or terracing tiles single layer on roof & disposal of retrieved material upto a distance n.exc 100m where directed, all as specified and directed. |
| 83 | Demolition of existing PCC as in form of roof padding incl backing over roof, any thickness including plastering and leaping (where full thickness removed or only a part there of disposal off rubbish upto a distance n.exc 100m, where directed. |
| 84 | M&L for cement concerete type C2 1:3:6 (20 mm graded aggrigate) as in filling and mass concerete etc complete all as specified and dirceted. |
| 85 | M&L for 10mm thick rendering on fair faces of brick/concrete surfaces in CM 1:4 finished even and smooth without using extra cement mixed with water proofing compound.(Note :-WPC shall be measured & paid separately) |
| 86 | Material and labour for roof surface treated with PU Elastoseal primer with Epoxy Primer to seal the pores and enhance the adhesion of the coating, supplying and applying single component waterproofing liquid membrane based on pure, elastomeric, polyurethane resin cold applied of spray/brush applied membrane with an elongation of 650%+ 50 and tensile strength not less than 2 Mpa, crack bridging ability not less than 2mm. No leakage upto 5 bars of water pressure. Shore Hardness > 50 Shore. The minimum thickness to be applied shall be 1.5 mm, (overall) in two layers (each layer 750 micron) or as per manufacturer’s instructions so as to achieve thickness not less than 1.5mm including providing & laying of protective Geotextile fabric 150 GSM over the entire membrane with proper overlaps of 75mm before laying SRI roof tiles complete all as specified and as directed. Note : (i) The treatment shall be carried out by authorised applicator approved by GE as per the manufacturerMake for PU Primer/ Membrane SIKA/ BASF, BERGER/ STP FOSROC/ SAINT GOBAIN, PIDILITE. |
| 87 | Making benching / Roof Kerbing with PCC (1:2:4) type B0 using WPC as per manufacturer\"s instruction along side wall adjoining to roof in concave shape complete all as specified and directed. Note : WPC shall be measured and paid separately. |
| 88 | Supply and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 10 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner complete all as specified and directed. |
| 89 | S&F in repair of PVC cabinet size 650 x 400mm, comprising of looking glass, space for bath soap, shampoo, tooth brush and paste, handle towel rail complete allas specified and as approved of any fo floowing.Makes :- HINDWARE / CERA / NEYCER / PARRYWARE/CLASSICcomplete all as specified and directed. |
| 90 | Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15 cm thickness below and above ground level,all as directed. |
| 91 | M&L 75 mm thick PCC 1:3:6 type D-2 (using 40mm graded stone aggregate) as in as in sub baseall as specified and directed. |
| 92 | M&L sand filling 25 mm thick under floor/over floor or in foundations including well ramming complete all as specified and directed. |
| 93 | M&L 60 mm thick M-35 grade coloured interlocking paver block in approved design/colour setin grey cement and pigment laid over compacted sub soil / sand all as specified and directed. |
| 94 | M&L for providing prrecast cement concrete Type B1 1:2:4 (20 mm graded aggregate) in appex stone/kerb stone with plain fair faces including chamfers, weathering throting etc and set in cement mortar 1:4 complete with joints to math size and shape as approved by GE. |
| 95 | Demolition of RCC slab , RCC tank, chajjas, kitchen slab, chimney and similar items complete all as specified and directed. |
| 96 | S&F Window Canopy which is made with a durable polycarbonate/Glass/ fiber/acrylic sheet and steelbrackets for roof covering/cladding to wall, fixed with hold fast complete all as specified and directed.(Note :As per Design approved by GE) |
| 97 | Demolition of concrete block masonry built in cement mortar or cement lime mortar complete all as specified and directed. |
| 98 | M&L for Pre-cast cement concrete block masonry (Type C1, 1:3:6, 20mm aggregate) with solid blocks, exc. 10cm in width and setting in cement mortar (1:6), complete all as specified and directed. |
| 99 | Site clearance complete all as specified and directed. |
| 100 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in any type of soil complete all as specified and directed. |
| 101 | M&L PCC 1:4:8 type D2 ( using 40 mm graded aggregate) in foundation filling and mass concreteetc complete etc.all as specified and as directed. |
| 102 | Use & waste offormwork to sides of flat surfaces of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed. |
| 103 | Use & waste form work to sides of concrete pillars, posts, struts, piers, columns and stanchion etc; rough finish surfaces complete all as specified and directed. |
| 104 | Use & waste offormwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and as directed. |
| 105 | Use & waste of Formwork for chullah hoods, chajjas through and similar items including edges, surface rough finish surfaces to receive the plaster, complete all as specified and as directed. |
| 106 | Use & waste offormwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) rough finish surfaces complete all as specified and as directed. |
| 107 | Use & waste offormwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC rough finish surfaces complete all as specified and directed. |
| 108 | M&L M-30 (Design Mix) using 20mm graded aggregatein RCC Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed. |
| 109 | M&L M-30 (Design Mix) using 20mm graded aggregatein RCC Columns, pillars, piers, posts and struts complete all as specified and directed. |
| 110 | M&L for M30 Design Mix (using 20mm graded stone aggregate) in RCC as in beams, lintel, lintel bands etc; complete all as specified and as directed. |
| 111 | M&L for M30 Design Mix (using 20mm graded stone aggregate) in RCC as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like etc; complete all as specified and as directed. |
| 112 | M&L for M30 Design Mix (using 20mm graded stone aggregate) in RCC as in chajjas etc; complete all as specified and as directed. |
| 113 | M&L Reinforcement TMT Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 114 | Ditto, but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed. |
| 115 | M&L Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and directed. |
| 116 | M&L Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed. |
| 117 | M&L Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and directed. |
| 118 | M&L Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified anddirected. |
| 119 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in any type of soil complete all as specified anddirected. |
| 120 | Removing excavated material exc. 250 m but n exc. 500 m and depositing where directed |
| 121 | M&L for carrying out water proofing treatment forroofs in the following stages -(i) Rendering 10mm thick in 1:4 mixed with integral water proofing liquid all as per manufacturer\"s instructions over concrete surfaces finished even and smooth with out using extra cement. (ii)First coat of bitumen primer confirming to IS 3384 @0.300 Kg/ Sqm over plastered surafces (iii) Second APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified (iv) Aluminium paint |
| 122 | M & L Pre-cast cement concrete block masonry with solid blocks, exc. 10 cm in width and 1:3:6 Type C1 (20 mm graded aggregate) set in CM 1:6 complete all as specified anddirected. |
| 123 | M & L for 10mm thick rendering on fair faces of brick work or concrete surfaces in CM ( 1:6 ) finished even and smooth (without using extra cement) on internal Wall complete all as specified anddirected. |
| 124 | M & L for 5mm thick rendering on fair faces of brick work or concrete surfaces in CM ( 1:3 ) finished even and smooth (without using extra lime or cement) on Ceiling complete all as specified anddirected. |
| 125 | M & L 15 Mm Thick (10 mm in 1:6 CM+ 5 mm in1:4 CM with WPC(measuredsaperately)) External Plaster On Fair Faces Of Walls Finished Even And Smooth (without Using Extra cement) complete all as specified anddirected. |
| 126 | M & L 75mm thick Cement concrete type D-2, 1:4:8 (40mm graded aggregate) as in sub base, floor etc complete all as specified anddirected. |
| 127 | Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified anddirected. |
| 128 | M&L for PCC 1:2:4 type B0 25 mm thickusing 12.5mm graded stone aggregates as in sub floors/base floors etc all as specified and directed. |
| 129 | S & F 165 x 60mm Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed. |
| 130 | M&L for Cement concrete (1:3:6) type C-0 using 12.5 mm graded stone aggregate as in fillings and mass concrete, filling backs of chowkats etccomplete all as specified anddirected. |
| 131 | S&F 30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sidescomplete all as specified anddirected. |
| 132 | S&F of factory made 30 mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) kiln seasoned and chemically pressure treated complete all as specified anddirected. |
| 133 | S & F powder coated anodised Aluminium alloy sections sliding windows with frames 92 X29.6 X1.10mm , 3 track sliding shutters duly fitted with neoprene beading, glazing clips, two shutters tinted glass panes 4.80 mm nominal thickness one shutter with stainless steel wire cloth 0.45mm dia and average width of aperture 1.4mm , aluminium alloy handles etc. complete all as specified and directed. Note : Making all edges i.e. cill and jamb good by cement mortar 1:3 |
| 134 | M & L powder coated aluminium deco grill medium grade of mesh size 75mmx75mm with 6mm square anodised aluminium bars fixed with aluminium frame of size 9x9x1 mm complete all as specified anddirected. |
| 135 | S&F 125 mm long Aluminium handles, cast type,anodised complete all as specified anddirected. |
| 136 | S&F 150mm long Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified anddirected. |
| 137 | S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified anddirected. |
| 138 | S&F 75 mm size Butt hinges, heavy weight, cold rolled mild steel, and fixed complete all as specified anddirected. |
| 139 | S&F 150mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified anddirected. |
| 140 | M&L Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 |
| 141 | M&L two coats of oil bound Distemper over a coat of chalk whitening/ concrete primer incl preparing the newly plastered surfaces of walls complete all as specified anddirected. |
| 142 | M&L for preparation of new plastered surface and applying two coat of cement base paint over one coat of alkalic resistant primer all as specified and as directed. |
| 143 | M&L for preparation of newplastered surfaces of wall & applying three coats of limewhite wash on ceilingetc complete all as specified anddirected. |
| 144 | M&L for preparing new or previously untreated surfaces of steel or iron work of any description and girth over 10cmand applying two coats of synthetic enamel paint complete all as specified andas directed. |
| 145 | S&F solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed. |
| 146 | S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat molded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for styles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rai ; Panelling of plain colourPVC sheet 5 mm thickness to be fitted in MS frame welded/sealed to the style and rails with suitable PVC sheet beading and joinedtogether with solvent cement complete all as specified and directed. |
| 147 | S&F of sheet glass ordinary quality 4 mm thick and glazing with oil putty or fixed with wooden beads or fixed with rubber gasket in squares any size of pane complete all as specified & as directed. |
| 148 | S&F 125 mm long Mild steel pressed handles oval type, stove enamelled black all as directed. |
| 149 | S&F 150mm long mild steel, barrel tower bolts stove enamelled and fixed complete all as specified anddirected. |
| 150 | S&F 250mm Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified anddirected. |
| 151 | S&F (concealed / open) 25mm outer diaCPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified anddirected. |
| 152 | S&F (concealed / open) 20mm outer diaCPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified anddirected. |
| 153 | S&F Vitreous Cliina wash basin, angle back, size 600x480mm white including brackets, cutting for and pinning in ends of brackets or erecting stand, 32mm Rubber or vulcanite plugs (waste) with rings and fitting and fixing including chromium plated brass or bronze chain and stay (chain n exc 50 cm in length) wit waste pipe complete all as specified anddirected. |
| 154 | S&F PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified anddirected. |
| 155 | S&F 1000 Ltr Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position incl 40mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed.Minimum weight 15mm- 142gms/ 20 mm - 210 gms / 25mm-455gms/ 40mm - 690 gms) complete all as specified anddirected. |
| 156 | S & F 600mmx450mm bevelled edge mirror of selected quality glass, mounted on6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup Washers complete all as specified anddirected. |
| 157 | S&F 15mm bore chromium plated bib taps, fancy type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified anddirected. |
| 158 | S&F pillar tap, brass, 15mm dia, with capston heads, chromium plated,fancy type screwed down, high pressure, with or without lettered hot or cold, with long shank, screwed shanks and fly nuts, screwed for iron pipes or for wash hand basin all as specified and as directed. |
| 159 | S&F 15mm bore stop valve/ angle stop cock chromium plated,fancy type cast copper alloy, screwed down, high pressure, screwed both ends for iron pipe with long shank and cup complete all as specified anddirected. |
| 160 | S&F Tubular towel rail, 20mm dia, aluminium anodised plated, D type, 60cm long between flanges complete all as specified anddirected. |
| 161 | S&F Grating doom 100mm dia of PTMT complete all as specified anddirected. |
| 162 | S&F wall mixer cast copper alloy Chromium Plated with capstain heads, fancy type screwed down high pressure, with or without letters \"Hot or Cold\" with long screwed shanks and flynut screwedfor 15 mm bore iron pipe or for unions, fixed in repairs, complete all as specified and directed. |
| 163 | S&Fchromium plated shower roses 125mm size with or without swivel joints, any size, including fixing to steel pipe or union suitable for 15mm bore pipe etc;complete all as specified anddirected. |
| 164 | S&F stainless steel health faucet witrh 1 Mtr tube and hoock complete all as specified and directed. Confirming to Cat part No ALD573 of jaguar/PRAYAG |
| 165 | S & F Soap dish, vitreous China white, approximate size 160x 160x90mm complete all as specified anddirected. |
| 166 | S & F Toilet paper holder, vitreous China,box type complete all as specified anddirected. |
| 167 | S&F PVC 10 ltr. Cap. valveless syphonic action type, flushing cictern, low level, white/ coloured with inlet, ball valve, float and handle including brackets and connection to pipe etc complete all as specified anddirected. |
| 168 | S&F vitreous China wash down water closet pan (Pedestal Pattern), white including white plastic seat cover with mild steel CP hinging device, suitable brass CP wash jet with 1.00 to 1.50m long tube incl making connection to inlet flush pipe, & to \"P\" or \"S\" draintrap, incl supply of long special \"P\" or \"S\" trapfixed complete all as specified and directed. |
| 169 | S & F PVC (SWR) pipes double socketed in any length with rubber ring joints fixed to walls 110mm complete all as specified anddirected. |
| 170 | S & F PVC (SWR) pipes double socketed, in any length with rubber ring joints, laid in trenches or in floors 110mm complete all as specified anddirected. |
| 171 | S & F PVC (SWR) vent cowl 110mm complete all as specified anddirected. |
| 172 | S & F PVC (SWR) pipes double socketed, in any length with rubber ring joints, laid in trenches or in floors 75mm complete all as specified anddirected. |
| 173 | M & L PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified anddirected. |
| 174 | S & F PVC (SWR) branch piece 110mm single (double Y) equal or unequal complete all as specified anddirected. |
| 175 | S & F PVC (SWR) bends any radius 110mm complete all as specified anddirected. |
| 176 | M & L PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75mm complete all as specified anddirected. |
| 177 | M & L Glazed ceramic coloured tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match incl backing coat of CM(1:3) 10mm complete all as specified anddirected. |
| 178 | M & L Coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl Screed bed or bedding layer of mortar CM(1:4) 15 mm thick for laying floorfinishes complete all as specified anddirected. |
| 179 | S&F of galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified & as directed. |
| 180 | M&L forPCC (1:3:6) type C2, (using40mm graded stone aggregate) as in plinth protection, 75 mm thick, finishing the surface even and smooth w/o using extra cement including forming & filling expensionjoints 65 mm deep x 10 mm wide filled with sealing compound grade Acomplete all as specified and directed. |
| 181 | Taking down carefully copper/alumunium point wiring for light, fan, bell, socket or power complete including fittings such as switches, ceiling roses pendents regulators, sockets and tube light fittings etc, removing materials from site or for reuse refixing and making good distrubed surface of wall, floors etc all as specified and directed. |
| 182 | Taking down main switches from DBs with sheet metal enclosure 08/04 way SPN/TPN DBsetc all as specified and directed. |
| 183 | M&L for point wiring with using 1.5 Sqmm (nominal area) multi standard copper conductor, single core, FRLS PVC insulated & unsheathed cable, 1100 volts grade with and including PVC conduit pipe of adequate size concealed type on wall / fixed to surface ceiling with PVC rawl plugswith sunken type pressed steel terminal box suitable for laminated board or Modular fititng board and junction boxes 1.6mm thick of suitable size, duly painted with one coat of red oxide primer and two coats of black bituminous paint for mounting fittings and wiring to be terminated in pressed steel sunken boxes with and including all accessories andusing 1.5 Sqmm (nominal area) stranded copper conductor single core conductor, FRLS PVC insulated & unsheathed cable as in earth wire connected to common earth dolly complete all as specified and directed forOne light/fan point controlled by one; one way switch complete all as specified and directed. NOTE :- (i) Quoted rate shall be deemed to include the cost of cutting chases in walls / pillars /column etc. of any description for concealing the boxes to required depth & making good the disturbed surface in CM 1:4 including finishing the surface to match with the existing surface. (ii)Fittings like switches, sockets, regulators, lamp holders, light fittings shall be measured and paid for separately under appropriate item of Schedule `A\".(iii) The quoted rates shall be deemed to be inclusive for provision of white cover plate and frame all as specfied and directed |
| 184 | -ditto- all as per item No 183 above but for one 5 pin socket 5 Amps on same board complete all as specified and directed |
| 185 | -ditto- all as per item No 183 above but for one 5 pin socket outlet 05 Amp independent board complete all as specified and directed |
| 186 | M & Lfor point wiring complete with proper colour coding using 1100 volts grade, 2.5 Sqmm, PVC insulated, FRLS,unsheathed wire with multi stranded copper conductor confirming to IS-694, Part II, ISI marked, drawn partly in and including PVC conduit concealed in walls etc including cutting chases and making good the same in CM 1:3 to match with the existing surfaces and partly drawn in and including PVC casing caping fixed on the surfaces of RCC slab/ ceiling/columns/beams etc with all accessories, fittings, PVC junction boxes etc. also inclduifng 2.5 Sqmm, PVC insulated, FRLS, unsheathed, 1100 Volts mutli-stranded copper conductor green colour as continous earth wire connected to common earth dolly all as specified and diretced for one 5Pin,6/16Amps,Socket outlet independent,complete all as specified and directed.NOTE :- (i) Quoted rate shall be deemed to include the cost of cutting chases in walls / pillars /column etc. of any description for concealing the boxes to required depth & making good the disturbed surface in CM 1:3 including finishing the surface to match with the existing surface. (ii)Fittings like switches, sockets, regulators, lamp holders, light fittings shall be measured and paid for separately under appropriate item of Schedule `A\".(iii) The quoted rates shall be deemed to be inclusive for provision of white cover plate and frame all as specfied and directed |
| 187 | Supply & fixing ceiling rose , surface bakelite3 terminal complete all as specified anddirected. |
| 188 | Supply & fixing modular fan regulator,120W- 2 module complete all as specified anddirected. |
| 189 | Supply & fixing switch modular type6 Amp single pole one way 230V complete all as specified anddirected. |
| 190 | Supply & fixing switch modular type16 Amp single pole one way 230V complete all as specified anddirected. |
| 191 | Supply & fixing socket modulartype 6 Amp2/3 pin single pole one way 230 V complete all as specified anddirected. |
| 192 | Supply & fixing socket modulartype 16 Amp2/3 pin single pole one way 230 V complete all as specified anddirected. |
| 193 | Supply and fixingin replacement To surface mounting slim/Box type LED flat panel 2\" x 2\"LEDs 36/40 watts Inlcuding Replacement of Unserviceable LED Drivers and Multistrip LEDs Suitable to Fitted on False ceiling by cutting to complete all as specified and directed. |
| 194 | S&F LED Batten T-5 ,integrated sleek extruded LED channel with acrylic cover, with and including 20 Wattlight and driver, prewired, provision of 0.5 Sqmm 3 core flexible copper conductor wirefor connecting from ceiling rose, complete all as specified and directed. LED batten must have technical specification specified below: - 20 W Wattage, Rated input voltage-140 V AC-270 V AC, Driver efficiency-88%, Lumens Efficiency-Min 100lm/w, starting voltage 90V and THD <=20 Colour Rendering index (CRI) >80, Colour Temperature-6500K, Cool daylight Light Effect, No harmful radiations, In built surge protection-2.5 kV, Isolation-3.75 kV and Zero mercury content. Make- Havells/Philips/Bajaj/Wipro/Jaquar as approved by the GE. |
| 195 | Supply & fix exhaust fan 300 mm sweep, 1200 rpm, 230V complete with louvers, Plastic body, bolts, nuts, washers, suitably embedded in windowwith provisioning offlexible three core wire for electrical connections from ceiling rose to fan all as specified and directed. (for bathroom) |
| 196 | Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM,Five star rated with brushless direct current motor (BLDC) |
| 197 | Supply and fix electric water heater,storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, anchor fastner Bolts etc.Completely all as specified and diretced for one 5Pin,6/16Amps,Socket outlet independent,complete all as specified and directed. Make : Jaquar/Havells/Racold with Minimum 01 Year warrentyNote : The rate quoted by the contractor also including provision of Hot and Cold water stainless steel connecting pipe 2ft long with Connecting bolt 15mm diaISI Marked complete all as specified & directed. |
| 198 | Supply and Fix Modular Type 3 module surface box including MCB Protected socket for current rating of 16A and MCB SP Modular type 16A currecnt rating with steel enclosure for surface mounted complete all as specified and directed. Make:Havells /Anchor/Legrand |
| 199 | Supply & fix sheet metal enclosure powder coated for MCB DB SPN 8 way double door with din rail and bus bar including making good to the disurbed surface matching with the existing complete all as specified and directed. |
| 200 | Supply and fix MCB SPN 240 volts 32 Amps breaking capacity 10 KA \"B\" Series rating complete all as specified and directed. |
| 201 | Supply and fix MCB SP 240 volts 6 to 32 Amps breaking capacity 10 KA \"C\" Series rating complete all as specified and directed. |
| 202 | Taking down unserviceable building security light fitting and Supply and fixing pressure die cast housing with epoxy power coated dark graphite grey colour finish. Prismatic polycarbonate cover with individual LED lenses 35 watt, AC 240 Volts 50 HZ ,\"IP66 protection, PF>0.95, LED light luminous efficiency shall not be less than 90 LumensWatt and the colour rendering index shall not be less than 70 and Correlated Colour Temperature is 6500K and light should complying ISl and BIS marking complete all as specified anddirected. Make: Philips/Havells/Osram |
| 203 | Supply and fix pipe bracket made out of 32 mm dia GI pipe, medium grade, upto 1.5 mtr long, bent to required shape and fixed onpole including necessary clamp/saddle and fixing by screw/bolt complete all as specified and directed. |
| 204 | Material and labour for earthing complete with GI earth plate electrode 600x600x6 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below ground lavel) with top edge of the plate not less than 1.5mtr below normal ground lavel connected to galvanised earth lead wire 4.0mm dia mean of bolts, nuts, check nuts and washer of brash all as shown in electrical plate No 5 connected to earthing test point all as specified or indicated including PCC pit and CI cover fullel with watering pipe, wire mess and copper lugs etc GI protection pipe 40 mm dia medium gradeincluding testing on completion all as specified and directed. |
| 205 | Excavation in trenches n.exc 1.5 m wide and n. exc 1.5 m in depth and getting outin soft/loose soil for removing/laying of cables complete all as specified and as directed. |
| 206 | Removing excavated material to a distance n.exc 50 m and depositing where directed at a level n.exc 1.5 mtr above the starting point complete all as specified and as directed. |
| 207 | Material and Labour for dry fine sand cushioning to under ground cables 8 cm thick before laying the cable and 15 cm thick after laying, stretching and testing the cable all as direted.Note : [Punned thickness 18 cm shall be measured & paid] |
| 208 | Supply and laying un-reinforced pre cast concrete cable cover, class LV type 1 with flat size 250mm x 150mm x 40mm complete all as specified and as directed. |
| 209 | Supply and laying GI pipe 50 mm, light grade for the protection of the cable passing through road crossing, etc complete all as specified and as directed. |
| 210 | Supply and laying in repairs cable LT XLPE insulated and screened PVC bedded, galvanised steel strip armoured electric power cable (heavy duty) with stranded aluminium conductor, 1100 Volts grade complete all as specified and directed by Engineer in charge for the 16 Sqmm 2 Core sizes including taking down existing u/s LT cable. |
| 211 | Material and labour for PCC 1:2:4 type B2(using 40 mm graded stone aggregate) forfilling the disturbed road opening for cable crossing include levelling with road surface and smooth finishing complete all as specified and directed. (for Road Cutting Repair) |
| 212 | Supply and fixing in any length UPVC pipe 25 mm dia manufacture as per ASTM-D-1785 as per IS-559, Sch-40 complete with fittings, laid in treanches in required length complete all as specified and directed. |
| 213 | All as per item no 212 here in before but of 20 mm dia complete all as specified and directed. |
| 214 | M & L for cutting the existing GI / PVC pipe 100 mm / 50 mm dia in position for insertion of new Tee for branch connection complete all as specified and directed. |
| 215 | S & FUPVC ball valve with operating handle (stop valve) of size(25 mm dia) both ends threaded complete suitable for fitting with ASTMD-1785, Sch40 UPVC pipes all as specified and directed. |
| 216 | Supply and fix in replacement XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100 volts grade of cross sectional area 25 sqmm 4 core complete all as specified and directed |
| 217 | Excavating in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundation etc for laying of cables, erection of poles, struts/ stays etc not exceeding 10 sqm on plan and getting out in any hard/dense soilon any type ofslope complete all as specified and directed. |
| 218 | M&L for sub main wiring complete two run of size 2.5 sqmm PVC insulated ,unsheathed, heavy duty 1100 volts grade (FRLS) multi-stranded copper conductorcable ,drawn partly in and including PVC conduit concealed in walls etc including cutting chases and making good in CM 1:3 to match with the existing surfaces and partly drawn in and including PVC casing capingfixed on the surfaces of RCC slab/ceiling/columns/beams etc with all accessories, fittings, PVC junction boxes etc, also including one run of 2.5 Sqmm, PVC insulated, FRLS, unsheathed, 1100 Volts multi-stranded copper conductor green colour as continous earth wire connected to common earth dolly and mains, complete all as specified and directed.(For Building security Lights & Power Point )Note: Three run 2.5 Sqmm PVC cable and one run of Conceled/Casing Caping & conduit will be measured as \"one unit\"length. |
| 219 | S & FTPNDB,415 volts,4 waydouble door, With provision for TP 63A MCCB as incomer and SP / TP MCBs as outgoing With neutral bars & earth bars complete all as specified and directed including making good to the disurbed surface matching with the existing also fixing MCB to the panel complete all as specified and directed. |
| 220 | Supply and fixing TPN 63 Amps 4P 415V 10KA \"B\" curve complete with connection testing and commissioning. and directed. |
| 221 | Supply and fix MCB SP 240 volts 6 to 32 Amps breaking capacity 10 KA \"B\" Series rating complete all as specified and directed. |
| 222 | Supply, installation, commissioning of metal top deep freezer single phase 240 volt 50 Hz with capacity of 530 ltr double door standard deep freezer BEE 5 star rated complete all specified and directed. |
| 223 | Supply and installation frost free double door refridgerators with smart inverter compressor, built in stabilizer, electric driven (single phase) of capacity 260 ltr frosffree BEE 5 star rated complete all specified and directed. |
| 224 | Supply and fix voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170V to 250V with output voltage stabilized at 230v with accuracy of 2.5% and of capacity 4000VA including fix voltage stabilizer to wall with necessary sheet and support all as specified and directed. |
| 225 | NOTE APPLICABLE FOR ALL ITEMS :- If rate quoted for similar/identical items in same part of Sch ‘A’ is at variance, the lowest rate quoted shall only be considered for payment to the contractor. |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
| 5 | Click here to download tender document | Tender Documents |
| 6 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
