Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Demolition cement concrete (unreinforcement) in ground floor and paving n exc 15 cm thickness (below or above ground level) & removal complete all rubbish materials complete all as specified and directed. |
| 2 | Demolition of brick work or stone/boulder masonry built in cement mortar incl all quoins, arches, pillars& precast concrete masonry etc complete all as specified & directed. |
| 3 | M&L for brick work with sub class \"B\" bricks, straight or curved on plan to any radius, built in 1:4 as in half brick thick wall complete all as specified and directed. |
| 4 | M&L for brick work with sub class \"B\" bricks, straight or curved on plan exceeding 6 mean radius, built in CM 1:6 complete all as specified and directed.. |
| 5 | M&L for 50mm thick PCC (1:3:6) type C-2 as in footpath/plinth protection & finishing the surface even & smooth without using extra cement complete all as specified & directed. |
| 6 | M&L for PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in cills, coping steps, tank staging, sesmic and other similar courses, lacing courses parapet and railing upto 60cm ht kneeler kerb and alike including weathering, slightly rounded or chemfered angle and throating complete all as specified and directed. |
| 7 | M&L rendering 15 mm thick in CM 1:6 on stone masonry surfaces or on other than fair faces of brick masonry finishedeven and smooth without using extra cement including taking down cement or cement lime plaster, any description on brick or stone walls,etc including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed. Note : Quoted rate is deemed to be inclusive for work at any height and location including cost of scaffolding and all other equipments reqd to execute the work complete all as specified and directed. |
| 8 | M&L rendering 15mm thick in CM 1:4 on fair faces of on stone/Brick masonry including WPC @ 3% by weight of cementfinished even and smooth without using extra cement including taking down old existing plaster of any type complete all as specified and directed.Note : Quoted rate is deemed to be inclusive for work at any height and location including cost of scaffolding and all other equipments reqd to execute the work also incl cost of WPC shall be incl in quoted rate only and nothing extra will be paid in this regard. |
| 9 | M&L rendering 5mm thick in CM 1:3 on concrete ceiling surfaces finished even and smooth without using extra cement including taking down cement or cement lime plaster, any description on brick or stone walls,etc including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed. |
| 10 | M&L rendering 15 mm thick in CM 1:6 on stone masonry surfaces or on other than fair faces of brick masonry finishedeven and smooth without using extra cement , any description on brick or stone walls,etc including racking out joints, hacking for key,scrubbing down with water etc, complete all as specified and directed. Note : Quoted rate is deemed to be inclusive for work at any height and location including cost of scaffolding and all other equipments reqd to execute the work complete all as specified and directed. |
| 11 | M&L rendering 15mm thick in CM 1:4 on fair faces of on stone/Brick masonry including WPC @ 3% by weight of cement finished even and smooth without using extra cement complete all as specified and directed.Note : Quoted rate is deemed to be inclusive for work at any height and location including cost of scaffolding and all other equipments reqd to execute the work also incl cost of WPC shall be incl in quoted rate only and nothing extra will be paid in this regard complete all as specified and directed. |
| 12 | M&L for Rough cast plaster on exterior wallsapplying the under coat of cement and sand morrtar 1:3 not less than 10mm thick and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (size between 6 to 12mm ) mixed with coarse sand and cement in the raio of 1:1:1 shall be applied and finished even.The mix of cement and sand shall made slightly wetter than normal for rendering to ensure that larger aggregate are thoroughly covered including dismantling old existing cement plaster complete all as specified and directed. |
| 13 | M&L preparation of newly plasterd surface of wall and applying two coats of oil bound distemper white or tinted over and including 2mm thick Birla wall care putty complete all as specified and directed. |
| 14 | M&L for preparing of newly plastered surfaces & applying three coat of white wash on ceiling etc complete all as specified and directed. |
| 15 | M&L for preparing new plaster wall surfaces by mechnical scraper and applying two coats water based premium acrylic smooth exterior emulsion(Apex ultima or equivlent) of approved colourwith silicon additive & Color stay Technology, Excellent Dirt Pick up resistance with low VOC less than 50 gram/ litre as per the LEEDS specifications, Anti Algal properties in two coats @ 1.79 ltr (undiluted)/ 10 sqm diluted with water as per manufacturer instructions applied over priming coat with fully automatic airless spray machine of paint application with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI.Allow 6-8 hrs to dry the surface in both the coats of paint over and including applying alayer of cement base wall care putty 2 mm thick as per manufacturars instructioncomplete all as specified and as directeduptoany height incuding necessary scaffolding.Note:- The quoated rate are including applying of cement wall care putty complete all as specified and directed. |
| 16 | M&L for Complete removal of existing treatment (White wash, colour wash, cement base paint, OBD or any other treatment) of wall by brooming down on steel wire brushing scrapping down smoke soot moulds, moss and efflorescent salts and trading oil greasy spot etc and applying two coats of oil bound distmper over and incl 2mm thick wall Care Puttyon walls complete all as specified and directed. |
| 17 | M&L for preparation of old surrfaces and applying two coats of white wash on ceiling complete all as specified and directed. |
| 18 | M&L for Complete removal of old existing treatmentfromwall surfaces by mechnical scraper and applying two coats water based premium acrylic smooth exterior emulsion(Apex ultima or equivlent) of approved colourwith silicon additive & Color stay Technology, Excellent Dirt Pick up resistance with low VOC less than 50 gram/ litre as per the LEEDS specifications, Anti Algal properties in two coats @ 1.79 ltr (undiluted)/ 10 sqm diluted with water as per manufacturer instructions applied over priming coat with fully automatic airless spray machine of paint application with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI.Allow 6-8 hrs to dry the surface in both the coats of paint over and including applying alayer of cement base wall care putty 2 mm thick as per manufacturars instructioncomplete all as specified and as directeduptoany height incuding necessary scaffolding.Note:- The quoated rate are including applying of cement wall care putty complete all as specified and directed. |
| 19 | M&L for glazed ceramic colour tiles in vertical surface 450X 300X 7 mm thick or any other size as approved by Engr-in-Charge set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 10 mm thick rendering in CM (1:4), including dismantling old tiles and removal of rubbish or dismantling items upto 1.0 Km from the site etc complete all as specified and directed. |
| 20 | M&L non skid ceramic coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.06 sqm but n.exc 0.11Sqm in floor etc, set and jointed in neat cement slurry and pointed in white and coloured cement to match coloured tiles including Screed bed of mortar 15mm thick for laying floor finishes CM (1:6) including dismantling old tiles and removal of rubbish or dismantling items upto 1.0 Km from the site etc complete all as specified and directed. |
| 21 | M&L non skid ceramic coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11 sqm but n.exc 0.18 Sqm in floor etc, set and jointed in neat cement slurry and pointed in white and coloured cement to match coloured tiles including Screed bed of mortar 15mm thick for laying floor finishes CM (1:6) including dismantling old tiles and removal of rubbish or dismantling items upto 1.0 Km from the site etc complete all as specified and directed. |
| 22 | M&L for Vitrified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors/wall etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchcoloured tiles including Screed bed of mortar 15mm thick for laying floor finishes in CM (1:6) including dismantling old tiles and removal of rubbish or dismantling items upto 1.0 Km from the site etc complete all as specified and directed. |
| 23 | All as per srl item No 22.000 but in skirting in CM 1:4. |
| 24 | S&F Granite (of any type) work 18-20mm thick (table rubbed and polished) in steps, jambs, pillars ,window cills,cooking platforms and like (including cutting for fixing of WHB, Sink etc) in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete including demolition old stone slab and removal of rubbish or dismantling items upto 1.0 Km from the site etc complete all as specified and directed.all as specified and directed |
| 25 | M&L for mirror polished machine cut kota stone flooring 18 to 20 mm thick over and including 20mm thick cement mortar srceed bed 1:6 set andjointed in neatcement slurry mixed with pigment to match the shed of the slab including rubbing polishing including dismantling old kota stone flooring with bedding and removal of rubbish or dismantling items upto 1.0 Km from the site etc complete all as specified and directed.etc complete all as specified and as directed |
| 26 | M&L for Mirror polished machine cut Kota stone slab 18-20 mm thick in riser of steps, skirting, dado and pillar laid over cement plaster in CM 1:4and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including dismantling old kota stone and removal of rubbish or dismantling items upto 1.0 Km from the site etc complete all as specified and directed. |
| 27 | Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, false ceiling etc any thickness, including cover fillets etc complete all as specified and directed. |
| 28 | M&L for suspendedfalse ceiling system using 4 mm thick\"E\" Board ceiling tiles classic/ designer as approved by GE of size 595 x 595mm (as approved by GE) fixed with and including galvanized iron powder coated GI Grid system suspendedfrom ceiling with provision of galvanized wire 4 mm dia with butterfly clips and wall taping screw, hold down clips for fixing the board to frame complete all as per manufacturer’s instructions, complete all as specified and directed.(a)Size of grid - 600 x 600 mm.(b)Size of main Tee – 39 x 24x0.30mm (c)Size of cross Tee – 24X24x0.3mm(d)Size of wall angle – 24 x 24x0.4mm |
| 29 | Taking down chowkats or frames with shutters (without taking off shutters frome the frames) n exc 1.5 but each complete all as specified & directed. |
| 30 | Taking down chowkats or frames with shutters (without taking off shutters frome the frames) exc 1.5 but n exc 4 sqm each complete all as specified & directed. |
| 31 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisturproof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with Four numbers 125mm long stainless steel butt hinges on each shuttrs of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed.. |
| 32 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type glazed and skelton door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisturproof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with Four numbers 125mm long stainless steel butt hinges on each shuttrs of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed.(Note :- Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm shall be included in quoted rate only.) |
| 33 | Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 X 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardanand fixed in position with MS hold fast/ugs/SS dash fasteners of required diaincluding necessary hold fast/lugs or SS dash fastner/necessary cutting hole in wall and making good the wall with filled the holes alongwith PCC 1:2:4 or CM 1:4 etc complete all as per direction of Engineer-in-Charge. |
| 34 | S&F aluminium powder coated ventilators alongwith necessary fitting such as hinges, handle, peg stay, tower bolt etc made out of thefollowing specifications :- (Net external size of ventilator shall be measured.Following items are included in this unit rate.)(a)Aluminium frame powder coated styles, bottom, top and middle rail of hollow section 50 mm x 25 mm x 1.80 mm thick.(b)Lower portion of ventilator shall be fixed with 4mm thick pin headed glass fixed with suitable aluminium beading clips and EPDM beading (rubber).(c)Upper portion shall be fixed withlouver guides fixed with 4mm thick pinheaded glass with suitable EPDM beading incl suitable handle and clips.(d) Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with suitable frame in upper panel. |
| 35 | S&F aluminium powder coated sliding window made of thefollowing specifications :- (Net outer size of window shall be measured.Following items are included in this unit rate.)(a)Provn of 03 track runners of size 92 x 31.75 x 1.10 mm.(b)Provn of glazed sliding shutters (02 Nos) of section 44 mm x 18 mm x 1.25 mm alongwith 4 mm thick heat observingglass with suitable EPDM beading and locking clips arrangement.(c)Provn of gauged sliding shutter of size44 mm x 18 mm x 1.25 mm alongwith Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm with suitable stainless screws and locking clips arrangement..(d) 12 mm dia square bar grill/ guard bar alongwith 25mm wide and 3mm thick ms flat strip frame to be fixed in wall with hole fastener or any other necessary screws etc complete. |
| 36 | S&F powder coated aluminium door anodised of approved colour ( size of frame :63.5mm x38.10mm x 2mm thick& size of shutter :door vertical (style ) with gasket of size 45mmx45mmx 2mm thick,top/bottom/middle rail of size 110mmx45mmx2mm,including S&F of5.5 mm thickfrosted glass with glazing clip, pvc track gasket, EPDM rubber gasket on glass of weather tightening alongwith recessed type handle - 02 Nos,hinges - 04 Nos, mortic lock - 01 Nos, Hydraulic door closer - 01 Nos on each shutter etc complete all as specified and directed. |
| 37 | S&F stainless steel sliding door bolt with hasp,staple (bolt type) 300mm long not less than 12mm dia with and incl minimum of 06 bolts and nuts, 4 on plate and 2 on staple and fixing complete all as specified and directed. |
| 38 | S&F stainless steel barrel tower bolts of extruded section and fixed 150 mm long complete all as specified and directed. |
| 39 | S&F stainless steel handles 125mm size fabricated type anodized ISI marked complete all as specified and directed. |
| 40 | S&F stainless steel barrel tower bolts of extruded section and fixed 200 mm long complete all as specified and directed. |
| 41 | S&F stainless steel handles 150mm size fabricated type anodized ISI marked complete all as specified and directed. |
| 42 | S&F 140 mm long Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring,with vulcanised rubber piece fixed in floor complete all as specified and directed. |
| 43 | S&F in repair Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or galvanised wire staples to wooden/steel/aluminium frames with beading complete all as specified & directed. |
| 44 | S&F vitreous china squatting pan of Orrisa pattern size 580mmx440mm white with integral foot rest (excluding flushing cistern and flush pipe complete incluidng provision of lime concrete bedding fixed in repair complete all as specified and directed. |
| 45 | Supplyand fixing PVC flushing cistern low level 10 ltr cap with inlet ball valve float and handle syphonic action type incl brackets and flush pipe of polythene of low or high density ISI marked complete all as specified and directed. |
| 46 | S&F in repair 15mm dia bib tap cast coper alloy chromium plated fancy type crutch or butter fly handle screwed down screwed for iron pipe or for brass ferrule and fixed as fixed in repair complete all as specified and directed. |
| 47 | S&F in repair 15mm dia stop valve/angle valve of copper alloy fancy type chromium platedscrewed down high pressure with crutch or butter fly handle screwed on both ends for iron pipe or for union fixed in repair complete all as specified and directed. |
| 48 | S&F in repair swivel shower rose(fancy type) chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed. |
| 49 | S&F 15mm dia concealed stop valve/angle valve of copper alloy fancy type chromium plated with long shank and cup (concealed type) screwed down high pressure with crutch or butter fly handle screwed on both ends for iron pipe or for union fixed in repair complete all as specified and directed. |
| 50 | S&F in repair 600mmx450mx5mm thick looking mirror of selected quality glass mounted on 6mm thick AC building board or commercial plywood incl framing and fixed to wooden plugs with chromium plated screws & cup washers & fixed complete all as specified and directed. |
| 51 | S&F in repair WHB flat back of Size 580x450mm incl brackets, waste pipe, waste coupling, and CP pillar tap etc incl cutting pinning in ends of brackets complete all as specified and directed. |
| 52 | S&F 32 mm dia PVC flexible waste pipe for WHB/Sink 600 mm long with PVC coupling all as directed fixed in repair complete all as specified and directed. |
| 53 | S&F 15mm diaconcealed galvanised iron tube medium grade with all fittings such as bends, elbowssockets, reducers etc and fixed to wall, ceiling or laid in floor with new fittings including cutting through wall floor etc including taking down old existing pipe complete all as specified and directed. |
| 54 | S&F20mm diaconcealed galvanised iron tube medium grade with all fittings such as bends, elbowssockets, reduces etc and fixed to wall, ceiling or laid in floor with new fittings including cutting through wall floor etc including taking down old existing pipe complete all as specified and directed. |
| 55 | S&F in repairs stainless steel sink with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste pipe & waste coupling; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe complete all as specified and directed. |
| 56 | S&F in repair Stop valves 20mm bore, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. |
| 57 | S&F 500 ltrs capacity rotational moulded polyethylene triple layered water storage tanks (cylinderical vertical with closed top) hoilsted and fixed in position all as specified in SSR Part-I including dismantling of existing water tank complete all as specified & directed. |
| 58 | S& Fixing in repair ball valve brass high pressure with polythene floatand fly nut screwed on iron pipe and fixed 20 mm bore of pipe complete all as specified and directed. |
| 59 | S&F in repair PVC connection 15mm size with PTMT nuts of length 600mm complete all as specified and directed. |
| 60 | S&F in repair Brass chromium plated Tubular towel rail 20mm dia, D type, 60cm long between flanges complete all as specified and directed. |
| 61 | S&F in repair Floor Drainer with Collar and Cockroach Trap/Jali with or without waste hole complete all as specified and directed. |
| 62 | S&F in repair brass chromium plated soap dish, complete all as specified and directed. |
| 63 | S&F in repair UPVC (SWR) pipes of 75 mm bore single socketed in any length fixed to wall i/c taking out old u/s PVC/CI pipe with fittings complete all as specified and directed. |
| 64 | S&F in repair UPVC (SWR) pipes of 110 mm bore single socketed in any length fixed to wall i/c taking out old u/s PVC/CI pipe with fittings complete all as specified and directed. |
| 65 | S&F in repair 75mm dia UPVC (SWR) floor trap, plain with grating including joining with solvent cement complete all as specified and directed. |
| 66 | S&F in repair 100mm dia UPVC (SWR) floor trap, plain with grating including joining with solvent cement complete all as specified and directed. |
| 67 | S&F in repair UPVC (SWR) bend 75mm bore of any radius complete all as specified and directed. |
| 68 | S&F in repair UPVC (SWR) bend 110 mm bore of any radius complete all as specified and directed. |
| 69 | S&F in repairs Stainless Steel (304 Grade) drapery rod of 25 mm inner dia (in length as directed ) of approved colour with & including matching finials at both ends and pair of SS brackets fixed at both ends with PVC rawl plug & steel screws on walls/beams including PVC curtain rings of matching colour @10 cm complete all as specified and directed. |
| 70 | Demolition of cement concrete (reinforced) in landing slab, chullah hoods, manhole covers , Roofs ,Floors, beams, stair case, landing, chajja and similar suspended work complete all as specified and directed. |
| 71 | M&L for TMT bars 10mm dia and over cut to length to shape required including cranking, bending spirally or hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. |
| 72 | M&L for form work to soffits of suspended slabs such as roof slabs etc for rough finished concrete surface complete all as specified and directed. |
| 73 | M&L for form work to SIdes for slabs and SIdes of RCC/PCC bands in walls, horizontal or sloping and SImilar work exc 10 cm but n exc 20 cm wide for fair finished concrete surface complete all as specified and directed. |
| 74 | M&L for RCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in roof, floor, slabs supported on walls complete all as specified and directed. |
| 75 | Demolition of existing lime concrete/PCC padding, roof treatment of any thickness laid over RCC roof/Chajjas etc removing complete layer of bitumen/ PCC upto RCCsurface, cleaning and washing of roof with water to remove dust etc as preparation to receive treatment incl removal rubbish material from outside of MOD Land etc complete all as specified and directed. |
| 76 | M&L for Providing cement concrete type B-0, 1:2:4 (using 12.5mm graded stone aggregate) as in padding and levelling course of floor/ roof etc complete all as specified & directed. |
| 77 | M&L for 20 mm thick screed bed on fair faces of concrete/brick surfaces in CM1:4 with water proofing compound @ 3 % of wt of cement finished even and smooth in order to maintain proper slope over new/existing roof surfaces for laying APP complete all as specified and directed. (WPC will be incl in quoted rate only and nothing will be paid extra in this regard.) |
| 78 | M&L water proofing treatement to RCC roof slab including parapet comprising of following course of treatement/specified from bottom to top (a)Applying Bituminous primer @ 0.40 Ltr per sqm over plastered surfaces of roof including parapet surfaces.NOTE : Bituminous primer shall be \"TANK MASTIC\" manufactured by M/S STP Ltd or \"EMW FLATE\" M/S Texas India Ltd (b)Over the priming coat laying one layer hot blown bitumen layer after that fixing APP based polymeric membrane of approved manufacturer, 3 mm thick weight not less 3.6 Kgs/Sqm reinforced with non woven polyester fabric weight not less than 150 gms per sqm polymeric membrane shall be taken to a height of 20 cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrane flushing and applying two coats of heat resistance paint over app memebrane complete all as spd and directed.Note:- Only horizontal roof/chajja area shall be measured for payment purpose. |
| 79 | M&L preparation of newly wooden surface/ old untreated of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 80 | S&F for preparation of new steel surface/old untreated of any description over 10cm width or girth & applying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed. |
| 81 | S & F factory made kitchen cabinet of depth 600mm made out of 18mm thick PVC celuka sheet having density not less than 650kg/cum one side decorative lamination & other side balancing lamination sheet consisiting of carcase 18mm thick PVC sheet incl shutters made out of 18mm thick PVC board all required brackets 5.5 screwes etc. The panels shall be fabricated using adhesive and screws where every required. All edge shall be covered with 2mm thick edge bonding tape or 90 degree edge bent finish as per make and specification mentioned as per drawing and specification approved by Engineer in charge. Note : (i) PVC celuka sheet manufactured by ISO 9001-2015 certified company, termite proof, water prrof & flame retradat PVC Sheet. (ii) PVC cabinet of required size fabricated by joining 18mm thick PVC celuka ply fixed with each other using solvent cement adhesive and screws and 18mm thick PVC sheet as backing of cabinet to be screw and solvent cement adhesive etc (iii) The cabinet box will be devided into two equal part with two leaf shutter and one shelf will be placed in caninate (iv) Cabinate will be fixed in wall with 4 x fastners etc and necessary fixing lugs (v) Each shutter will be provided with SS handle of 75mm, CP Piano hinges, magnet/catcher (vi) The quoted rates are incl the rates of all fifftings and fixture and dismantling and taking down old kitchen cabinet of any type complete all as specifed. The measured area shall be front elevation.Note : Items like cupboard knobs, stainless steel channel, CP plate clip hinges, handles are included in the mentioned rates and as per manufacturesrs specification and drawing.The measured area shall be front elevation. |
| 82 | Supplying and fixing in repair factory made PVC shutter of 18 mmthickness consisting of panel of 18 mmthick celluca ply of density 600 Kg.cbm densitymanufactured by an ISO 9000 certified company using for shutter celluca ply 18 mm thick cut in desired size of shutter and fixed with frame of kitchen accesory/cubboard at all four edges of shutter using 13/6 size self tapping steel screws below cooking platform. The thickness of the shutter is edfe painted by matching colour of PVC ink of plain colour of PVC sheet using including dismantling old boarding any description complete all as specified and directed by Engineer-in-Charge and manufacturers specification.Note : Items like cupboard knobs, stainless steel channel, CP plate clip hinges are included in the mentioned rates and as per manufacturesrs specification and drawing.The measured area shall be front elevation. |
| 83 | M&L for providing and injecting chemical emulsion for post constructional anti termite treatment alongwith the external/ internal wall below concrete or masonry apron using chemical emulsion at the rate of 2.25 litre per linear meter incl drilling and plugging 12mm dia holes with CM 1:2 to match the existing floors drilling and plugging holes etc complete all as specified and directed. |
| 84 | M&L for providing and injecting chemical emulsion for post constructional anti termite Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors etc complete all as specified and directed. |
| 85 | Demolition of Stone slabs and tiles laid bedded and pointed in any mortar of any description or thickness in floors, aprons etc complete all as specified and directed. |
| 86 | M & L for 25mm thick cement concrete (1:2:4) type B0 using 12.5 mm thick graded stone aggregate as in base or sub-base or as in floor for leveling course etc finished even & smooth or rough including necessary form work complete all as specified and directed. |
| 87 | M&L for Vitrified tiles (dark shade / double charged/ Ultra charged) 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm as in floors etc. laid over and including 15 mm screed bed or bedding layerin CM 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile etc complete all as specified and directed. |
| 88 | M&L for false ceilings using GI powder coated sanp grid system with roll-formed made out of hot drip galvanised steel capings (Powder coated) main runner 38x24mm, cross Tee 29x24mm and wall angle 24x24mm members 1mm thick, suspended with 4mm dia GI wire for capable to taking the weight upto 12 Kg/Sqm) with Hangers of 6 mm dia. G.I. (upto 1200mm length) adjusting level clip fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long, of size as approved by Engr-in-Charge, fixed with and including wall taping screw including butterfly clips, hold down clips for fixing the board to frame complete all as per manufacturer’s instructions, complete all as specified and directed. |
| 89 | S&F 6mm thick designer Non asbestos prepainted fibre cement building boards of any texture as approved by Engr-in-charge fixed or laid/ inserted to timber/GI/Aluminium frame work with screws fixed to the ceiling section with necessary accessories of make Everest ceiling andgrid system Regular T-2430 or its equivalent Make of \"Ramco/Charminar/Armstrong\" or any other make as per CA condition etc complete, all as specified and directed. |
| 90 | S&F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and as directed etc complete all as specified and directed. |
| 91 | S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specificatioand as directed etc complete, all as specified and directed. |
| 92 | Taking down carefully copper/aluminium point wiring of any size (light, socket or power) complete (fittings such as switches, ceiling roses, pendants, regulatos, sockets etc to be measured separately),and making good disturbed surfaces of walls, floors etc to match with existing surfaces complete all as specified and directed. |
| 93 | M&L for concealed Point wiring for One Light point controlled by one, one way switch with two single core PVC insulate, unsheathed multistranded copper conductorcable of size 1.5 sq.mm (FRLS) drawn in and including electrical grade PVC conduit20 mm dia concealed on wall/ceiling/floorincluding PVC insulated unsheathed earth wire with multi stranded copper conductor of size 1.5 sq.mm(FRLS) including Modular MS shunk sheet metal box with modular cover plate of required Module with brass counter shunk screws with washer complete all as specified and directed. Note - quoted rate shall include cost of cutting chases in Stone/Brick Wall for inserting PVC Conduit and Cost of Modular Cover plate of required module and making good to the disturbed surfaces including plastering andpaintingto match with the existing colour. |
| 94 | All as per srl item No 93.00 but for One 3 pinswitch socket outlet, 5 Ampon the same board with other switches. |
| 95 | All as per srl item No 93.00 but for One 3 pin 5 amps switch socket outlet pointon independent board. |
| 96 | All as per srl item No 93.00 but for One Ceiling fan/Exhaust Fan point controlled by one switch and regulator |
| 97 | All as per srl item No 93.00 but for wiring with 4.0 sq.mm multistranded cable and earth wire with copper conductor of size 4.0 sq.mm for 15 amps power/geyser point. |
| 98 | All as per srl item No 93.00 but for one 3 pin 15/16 Amps socket outlet controlled by one 15/16 Amps switch on independent board with 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour. |
| 99 | Supply and fixing in repair of Modular switch, one way 6 Amp, 1 module, piano type, 230/250 volts grade on top covers including taking down of old U/S one (catered in point wiring above) complete all as specified and directed. |
| 100 | All as per srl item No 99.00 but for Modular switch, one way 16 Amp, 1 module |
| 101 | Supply and fix in repair of Modular socket outlet 2in1, 3pin 5A, 2 module multipurpose use, flush mounting type, 230/250 Volts grade on Top covers including taking down of old U/S one (catered in point wiring above) complete all as specified and directed. |
| 102 | All as per srl item No 101.00 but for Modular socket outlet 2in1, 3 pin 15 Amps flush type |
| 103 | Supply and fix in repair U/S ceiling rose surface bakelite two to three terminals/plate, polycarbonate, isolated body including taking down of old U/S one complete all as specified and as directed by Engr-In-Charge. |
| 104 | Supply and fixing in repair PVC Blanking Plates one way with internal lock including taking down of Old U/S one complete all as specified and as directed by Engr-In-Charge. |
| 105 | S & F in repair stepped type electronic fan regulator flush type on modular cover plate of Elec trical Boards including taking down of old U/S one as reqd complete all as specified and directed by Engr in charge. |
| 106 | Supply and fix in repair Lamp holder, PVC/Polycarbonate type complete with lamp LED 9 Watt for Batten fitting with back plate and all fittings complete including taking down of old U/S one all as specified and directed by Engr-In-Charge |
| 107 | Supply and fix in repair wall mounted decorative Lights aesthetically designed with elegant frosted glass casing in durable metallic housing inbuilt with bulb holder two pin or Screwed type includinginsulated body with back plate for angle/batten fitting along with LED Bulb warm white colour 09 Watt complete including taking down of old U/S one complete all as specified and directed. Make/Model : Havells : Floretine WL1LSE27SSLHFOAJD1TZ1I060/Phillips Nerobless/Bajaj/Crompton |
| 108 | Supply and fixing in repair LED 36 Watt ultra slim edge 2x2 feet lit panel in aluminium casing recess mounted square fixtures in white finish suitable for low ceiling height, 3 in 1 , 3K,4K,6K with & including LED prewired and connecting up dismantling of old UNSV recessed mounted light Complete including taking down of old U/S one complete all as specified and directed. |
| 109 | Supply & fix in repair recess type, 36 watt LED panel light Sky Type (600x600 mm) complete with fittings integrated electronic driver,energy efficient, 230 volts, co- relatedcolour temperature (CCT) of 6500K, white coloured clouds in sky blue coloured background complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete including taking down of old U/S one complete all as specified and directed. |
| 110 | Supply and fix in repair LED batten (1.2m) made of CRCA sheet housing with a PC glossy diffisure duly prewired connection having nominal system lumen output of 2000 lumens at a minimum system efficiency of 115 lumen per watt and total power consumption not more than 20 watt including driver. it should have rated system life time of 40000 burning hours at L70 and should have a temperature of 6500 K CRI >80, thd <10 and PF>0.95 complete including taking down of old U/S one complete all as specified and directed.Make - Crompton Cat Part CIS-305-40-57-SL-DP-NWH, Philips Cat part BN308C LED20S-6500 L120 PSU WH, Havells Cat Part STOUTPLUS600BS20WLED840SPCWH |
| 111 | Supply and fix in repair Surface mounted COB LED fixture of 18 Watt with pressure die cast aluminium housing heat sink and clear PC as a Cover in white coated powder finish with integrated electronic LED driver and prewired connection having nominal system lumen output of 2000 lumens at a minimum system efficiency of 115 lumen per watt and total power consumption not more than 18 watt . it should have rated system life time of 40000 burning hours at L70 and should have a temperature of 6500 K CRI >80, thd <10 and PF>0.95 complete including taking down of old U/S one complete all as specified and directed. Make/Model: Crysta Deco Surf COB 18 W 6K Chrome W, Cat Part No.LHEEBGPGUE1W018 in Havells |
| 112 | Supply and fixing in repair LED light fitting as building security lights of 45 Watt Cap 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, with epoxy powder coated CRCA sheet steel grey tray, clear acrylic cover,incl street light bracket made out of 25 mm dia GI medium grade pipe 0.6 mtr long complete with 2 sets of FI clamps made out of 30x5 MS flat & nuts, bolts & washer including painting to clamp with two coats of aluminium silver paint over a coat of primer, with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete including taking down of old U/S one complete all as specified and directed. |
| 113 | Supply & fix in repair LEDpost top lanterns of 20 Watt rated power, warm white colour and rated CCT 3000K, IP65 aesthatically designed spun Al spigot for mounting LED Driver and spun aluminium canopy which is painted white inside. Epoxy powder coated matt black finish after phosphochromate treatment, weather proof construction having robust design delivers to meet the landscaping needs, Luminaire type,Opalinediffuser suitable to be fixed over galvanised pole of diameter upto 50mm,complete including taking down of old U/S one complete all as specified and directed. |
| 114 | S&F sheet metal enclosureconcealed in wall incl making good of disturbed surfaces double door type suitable for fixing MCB\"s, SPN with 200 Amps rated bus bar, 8 Way, 230 Volts and including taking down old U/S DB ,SPN,8 way complete all as specified & directed. |
| 115 | Supply and fix in repair VerticalTPN DB 4 way suitable for Double Pole outgoing MCB-40 Amp-04 Nos with incoming 100 Amps, 16 KA, MCCB 4 pole-01 Nos complete with 250 Amps rated Copper busbar flush mounting, double door, proction class IP-30, IK08 complete including taking down of old U/S one complete all as specified and directed. |
| 116 | Supply and fixing in repair SP 6-32 Amp, 240V, 10KA \"C\" curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete including taking down of old U/S one complete all as specified and directed. |
| 117 | All as per srl item No 116.00 but for SPN 40-63 Amps |
| 118 | S&F in repair modular AC Box 3 Module complete with 01 No. 32 Amps 3 Pin Socket Outlet and 1 Nos Single pole MCB 32 Amps & including taking down old U/S enclosure complete all as specified & directed . |
| 119 | Material & Labour in repair for Sub Main Wiring in repair with two run single core 6 Sqmm PVC insulated unsheathed(FRLS) cable with stranded copper conductor drawn in PVC conduit & accessories Suitable size with and including 6 Sqmm copper green colour earth wire Complete including taking down of old U/S one and cutting chases in stone or brick wall upto required depth for concealing the conduit of min external dia upto 25 mm to pass the submain wiring complete all as specified and directed.NOTE-two run of 6 sq.mm & One run of 6 sq.mm & One run of PVC conduit with accessories shall be measured as One length. |
| 120 | Material and labour in repair for earthing complete with galvanized steel earth plate electrode 60cmx60cmx6.30mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level and connected to and including galvanized iron earth wire 4 mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No 3 of SSR Part-I and connection to main switch board/Test point/panel/equipment and testing on completion including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exc 50 metre, charcoal and salt in alternate layer 15 cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering and 15 mm bore 3.00 metre long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25 mmx3mm, bolts, nuts and washers,PCCchamber (1:3:6) type C1, 40mm thick precast RCC cover 1:2:4 type B1 shall be provided on CI frame etc complete all as specified & directed. |
| 121 | Supply and lay in repairs and testing of cable of 95 Sqmm 3.5 Core LT XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured, electric power cable heavy duty with stranded aluminum conductor, 1100 Volts grade, complete all as specified and directed.Note:-Excavation, earthwork, will be measured and paid separately under respective items of this Schedule. The rates quoted by the contractor for this item shall be deemed to include the rates incurred on account of taking down of old U/S Cable and no additional payment shall be made on account of the same. |
| 122 | All as per srl item No 121.00 but for 35 Sqmm 3.5 Core. |
| 123 | All as per srl item No 121.00 but for 10 Sqmm 2.0 Core |
| 124 | Excavation in trenches not exc 1.5 m wide and n. exc 1.5 m deep in soft/loose soil for foundation/ cable etc n exc 10 Sqm on plan and n exc 1.5 Sqm in depth all as specified and directed by Engr-in-Charge |
| 125 | Returning, filling in including spreading levelling, watering and well ramming in layer n. exc 25 cm thick complete all as specified and directed |
| 126 | Removing surplus soil to a distance n. exc 50 m and depositing where directed at level n. exc 1.5 m above the starting point complete all as specified and directed |
| 127 | Supply and spreading, levelling river sand in trenches for cables cushioning on top and bottom of cable complete all as specified and directed. |
| 128 | M&L brick protection with sub class \"B\" brick laid flat across the cable complete all as specified and directed. |
| 129 | M&L for boring under roads for crossing of UG Cables complete all as specified and directed. |
| 130 | Supply and fix GI Pipe light grade of size 40 mmlaid in trenches under road/fixed on wall/pole for cable protection complete all as specified and directed by Engr-In-Charge |
| 131 | Supply and fixing in repair of 25 mm bore GI water tubing IS-1239 marked, medium grade, in replacement including all necessary pipe fittingslaid in trenches, on wall, under floor, under road on same or new route and making good the disturbed portion as existing and including taking down of old unserviciable pipe complete all as specified and directed.Note :-Excavation and Earth work will be measured and paid separately |
| 132 | Supply & install, testing & commissioning in repair LT control panelcompartmental type,Lockable fabricationmade by 3.15 mm thick sheet CRCA approved weather proof design framed on angle iron (40mmx40mmx6mm) double door front and rear openable both side opening shutters duly painted two coat with siemens gray color, cable entry with glands, foundation /grouting on & including PCC as per site requirement and taking down of old U/S LT Panel with the following :-(a) Al bus bar300 Amp Cap- 1 Set ( Set of 4 strips)(b) MCCB 160 Amp,4 Pole, 25 KA with spreader links - 1 Nos(Incoming) (c) MCCB 125 Amp,4 Pole,16 KA with spreader links - 2 Nos(Outgoing)(d) MCCB 63 Amp,4 Pole,16 KA with spreader links -2 Nos(Outgoing)(e) Indicating fuse LED type R,Y,B - 3 Nos(f) On Load Change Over Switch 100 Amps - 01 Nos |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
