|
| 1 | Building Works |
| 2 | Carriage of excavated material up to 2 km including loading, unloading & stacking |
| 3 | Earthwork in excavation by mechanical means in foundation trenches (all kinds of soil) |
| 4 | Filling available excavated earth in plinth & trenches, watered and rammed |
| 5 | Supplying & filling in plinth with sand under floors including watering & compaction |
| 6 | Pre-coMRtruction anti-termite treatment to top of plinth and wall-floor junction (complete as per IS 6313 Part II) |
| 7 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size) |
| 8 | PCC 1:4:8 (M7.5) in foundations and plinth |
| 9 | PCC 1:2:4 in copings, sills, anchor blocks, etc. |
| 10 | 40 mm thick DPC in 1:2:4 concrete |
| 11 | Extra for waterproofing admixture in concrete |
| 12 | Bitumen coat over DPC (VG-10, 1.7 kg/m²) |
| 13 | 50 mm plinth protection in 1:3:6 CC over brick ballast |
| 14 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing:1:1½:3 (1 cement : 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 15 | Centering and shuttering including strutting, propping etc. and removal of form for all heights: :Foundations, footings, bases of columns, etc. for mass concrete |
| 16 | Columns, Pillars, Piers, Abutments, Posts and Struts |
| 17 | Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like |
| 18 | Edges of slabs and breaks in floors and wallsUnder 20 cms wide |
| 19 | Suspended floors, roofs, landings, balconies and access platform. with water proof ply 12 mm thick |
| 20 | Lintels, beams, plinth beams, girders, bressumers and cantilevers. with water proof ply 12 mm thick |
| 21 | Reinforcement Fe-500D up to plinth level |
| 22 | Reinforcement Fe-500D above plinth level |
| 23 | RCC M25 (machine batched) up to & above plinth level, incl. pumping & admixtures |
| 24 | Design mix M-25 RCC above plinth to floor V level |
| 25 | Addl. cement over design mix |
| 26 | Brick work in foundation & plinth, CM 1:6, class 7.5 FPS (non-modular) |
| 27 | Half brick masonry in foundation & plinth, CM 1:4 |
| 28 | Brick work in superstructure up to floor V, CM 1:6 |
| 29 | Half brick masonry in superstructure up to floor V, CM 1:4 |
| 30 | Extra: 2 Nos. 6 mm MS bars @ every 3rd course in half brick masonry |
| 31 | Brick edging 7 cm × 11.4 cm to plinth protection in CM 1:4 |
| 32 | 18 mm granite (gang saw cut, premoulded) over 20 mm CM 1:4 – slabs >0.5 sqm |
| 33 | Edge moulding & polish — granite |
| 34 | Extra for fixing marble/granite in facias & drops ≤ 150 mm width using epoxy adhesive |
| 35 | Extra for opening in granite counter for sink / basin incl. polishing edges |
| 36 | Wood work in frames (2nd class teak) |
| 37 | Extra for frosted glass panes 4 mm (in lieu of clear) |
| 38 | Flush door shutters, decorative, 25 mm (cupboards) |
| 39 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 9.20.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary scrws |
| 40 | Flush door shutters 35 mm with SS butt hinges, IS:2202 |
| 41 | Extra lipping with 2nd class teak battens (all edges) |
| 42 | Wire gauge shutters 35 mm thick (hollock wood frame) |
| 43 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to steel windows by welding |
| 44 | Fly-proof MS wire gauge with 12 mm MS U-beading |
| 45 | Providing and fixing ISI marked oxidised M.S. pressed butt hinges with necessary screws etc. complete.125x65x2.12 mm |
| 46 | Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 250x10 mm |
| 47 | Providing and fixing ISi marked oxidised M.S. door latches conforming to IS:5930 with screws etc. complete : 300x20x6 mm |
| 48 | Oxidised MS casement stays 250 mm (≥280 g) |
| 49 | Aluminium sliding door bolts 250×16 mm, anodised |
| 50 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 300x10 mm |
| 51 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm |
| 52 | Aluminium hanging floor door stopper, twin rubber |
| 53 | Decorative HPL sheet 1.5 mm, plain/woodgrain, Type-S |
| 54 | Cupboard shutters 25 mm veneered board (Grade I) with decorative veneer one side |
| 55 | Providing and fixing to existing door frames.30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of \"H\" section, a uPVC hollow section of size 100x30 mm and 2 mm (± 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. \"U\" cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness . The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer\"s specification and direction of Engineer-in-charge. |
| 56 | Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment).Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3coarse sand : 6 graded stone aggregate 20 mm nominal size) |
| 57 | Extra for providing and fixing steel beading of size 10 x 10 x 1.6 mm (box type), approved shape and section with screws instead of glazing clips and metal sash putty, in steel doors, windows, ventilators and composite unit |
| 58 | Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat ofapproved steel primer.Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3coarse sand : 6 graded stone aggregate 20 mm |
| 59 | Built-up tubular trusses/steel work incl. primer, welded/bolted |
| 60 | Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment). Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) |
| 61 | T-iron frames for doors/windows |
| 62 | CI/MS sheet box for ceiling fan clamp with 12 mm bar clamp |
| 63 | Steel work welded in gratings/frames/guard bars etc., primed |
| 64 | Handrail in MS tube incl. primer |
| 65 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 66 | Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete. Galvanised M.S. Wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides |
| 67 | Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.0 mm thick glass panes |
| 68 | Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge. |
| 69 | Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with Jamuna sand, with common burnt clay non modular bricks. |
| 70 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :25 mm thick |
| 71 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. |
| 72 | Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab. |
| 73 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm |
| 74 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 500x500 mm |
| 75 | Vitrified floor tiles 600×600 mm, 12 mm thick, laid with cement mortar 1:3 and joints grouted |
| 76 | Providing and laying pressed clay tiles (as per approved pattern 20 mm nominal thickness of approved size) on roofs jointed with cement mortar 1:4 (1 cement : 4 coarse sand) mixed with 2% integral water proofing compound, laid over a bed of 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) and finished neat complete. |
| 77 | Making khurras 45×45 cm in 1:2:4 CC over 1 m×1 m×400 mic PVC sheet with 12 mm 1:3 plaster & neat finish |
| 78 | 12 mm cement plaster 1:6 (1 cement : 6 coarse sand) |
| 79 | 15 mm cement plaster on rough side of single or half brick wall of mix: 1:6 (1 cement: 6 coarse sand) |
| 80 | 18 mm plaster in two coats |
| 81 | Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement.20 mm cement plaster |
| 82 | 6 mm cement plaster 1:3 (1 cement : 3 fine sand) |
| 83 | White washing with lime (new work, ≥3 coats) |
| 84 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer |
| 85 | Textured exterior paint, two or more coats with primer |
| 86 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacturePainting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture |
| 87 | Ready-mixed aluminium primer on wood/ply |
| 88 | Red-oxide zinc-chromate primer on steel/GI works |
| 89 | Synthetic enamel paint, two or more coats |
| 90 | Black bitumastic paint, two or more coats |
| 91 | Washed stone grit plaster on exterior walls height upto 10 metre above ground level, in two layers, under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand ), furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 2 Kg of cement per square metre, top layer 15 mm cement plaster 1:1/ 2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10 mm nominal size), in panels with groove all around as per approved pattern, including scrubbing and washing the top layer with brushes and water to expose the stone chippings ,complete as per specification and direction of Engineer-in-charge (payment for providing grooves shall be made separately) |
| 92 | White-cement based putty (avg 1 mm) |
| 93 | Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour |
| 94 | Renewing glass panes, with putty and nails wherever necessary including racking out the old putty:Float glass panes of nominal thickness 4 mm (weightnot less than 10kg/sqm) |
| 95 | Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying |
| 96 | Integral cement-based waterproofing treatment (avg 120 mm) |
| 97 | Waterproofing treatment for sunken portions (4-course) |
| 98 | Providing & fixing 0.47mm thick Galvalume sheet roofing including vertical surface fixed with J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead . |
| 99 | Providing and laying cinder filling in sunken floors and other locatioMRwith approved quality cinder including watering and light ramming etc.required for proper compaction/completion of the work complete in all respects as per drawings and as directed by the Engineer in Charge. |
| 100 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) traMRparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 101 | Providing and fixing aluminium door buffer of approved make, design and colour with necessary screws etc all complete as directed and specified by the Engineer-in-Charge : |
| 102 | Providing and laying 1st quality ceramic glazed Anti skid floortiles of size 300x300 mm (thickness to be specified by the manufacturer) conforming to IS:15622 in all colours, shades, sizes as approved over 20 mm thick bed of Cement Mortar 1: 4 (1 cement : 4 Coarse Sand) including pointing the joints with white cement and matching pigment etc complete in all respects as per specificatioMR/drawings and to the entire satisfaction to the Engineer-in-Charge : |
| 103 | Providing and fixing false ceiling at all heights ….12 mm plain gypsum board ceiling incl. finishing |
| 104 | Plumbing works |
| 105 | Providing & fixing stone slab table rubbed, edges rounded and polished of size 75×50 cm and 1.8 cm thick in urinal partitions – White Agaria Marble Stone |
| 106 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot restsW.C. pan with ISI marked white solid plastic seat and lid |
| 107 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required W.C. pan with ISI marked white solid plastic seat and lid |
| 108 | Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required :Single half stall urinal with 5 litre P.V.C. automatic flushing cistern |
| 109 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps |
| 110 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink with drain board |
| 111 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. 10 litre capacity – White |
| 112 | Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. (a) 15 mm nominal dia |
| 113 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Rectangular shape 453x357 mm |
| 114 | Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. |
| 115 | Providing and fixing toilet paper holder :C.P. brass |
| 116 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. |
| 117 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms |
| 118 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. |
| 119 | Pedestal type EWC with 10 L PVC cistern, IS:7231 – with ISI marked white solid plastic seat & lid |
| 120 | 8 mm dia C.P./S.S. jet with flexible tube (1 m) to EWC |
| 121 | PTMT bottle trap 38 mm single piece moulded |
| 122 | PTMT liquid soap container (109×125×112 mm) with bracket |
| 123 | PTMT towel rail 600 mm long |
| 124 | C.P. brass shower rose, 100 mm dia |
| 125 | PTMT towel ring, trapezoidal 215×200 mm |
| 126 | C.P. brass single lever telephonic wall mixer, 15 mm dia |
| 127 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.15 mm nominal outer dia Pipes |
| 128 | 25 mm nominal outer dia Pipes |
| 129 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.100 mm nominal inner dia Pipes |
| 130 | Providing and fixing brass bib cock of approved quality : 15 mm nominal bore |
| 131 | Providing and fixing brass stop cock of approved quality : 15 mm nominal bore |
| 132 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore |
| 133 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :100 mm diameter |
| 134 | Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : |
| 135 | Providing and fixing PTMT pillar cock of approved quality and colour. 15 mm nominal bore, 107 mm long, weighing not less than 110 gms |
| 136 | uPVC connection pipe with brass unions, 45 cm, 15 mm bore |
| 137 | C.P. brass bib cock, 15 mm |
| 138 | C.P. brass angle valve for basin/geyser, 15 mm |
| 139 | Wash basin with CI brackets & 15 mm CP brass single-hole basin mixer, 550×400 mm |
| 140 | Indian type W.C. Orissa pattern 580×440 mm with 10 L PVC cistern |
| 141 | PVC waste pipe for sink, flexible, 32 mm dia |
| 142 | MS holder bat clamps with 10×10×10 cm CC block 1:2:4 for 100 mm dia CI pipe |
| 143 | PTMT grating, circular, 125 mm dia |
| 144 | CC 1:5:10 all-round CI hubless pipe incl. bed concrete, 100 mm dia |
| 145 | Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design. |
| 146 | Constructing soak pit 1.20x1.20x1.20 m filled with brickbats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design |
| 147 | UPVC (SWR) Type-B pipe 40 mm dia with fittings & clamps etc. |
| 148 | UPVC (SWR) Type-B pipe 50 mm dia with fittings & clamps etc. |
| 149 | UPVC (SWR) Type-B pipe 110 mm dia with fittings & clamps etc. |
| 150 | UPVC(SWR) Multi Floor Trap 110×75×40, with 63 mm i/d outlet |
| 151 | UPVC(SWR) Nahani Trap 110×90, with 90 mm i/d outlet |
| 152 | End cap (door piece) uPVC, with 110 OD |
| 153 | uPVC 110 mm P-Trap (min 50 mm water seal) |
| 154 | Pipe inlet fittings (uPVC) to P-traps (max 3 inlets 40/50/75 mm) |
| 155 | Mosquito-proof coupling, 25 mm dia |
| 156 | CPVC pipe exposed, 15 mm OD |
| 157 | CPVC pipe exposed, 20 mm OD |
| 158 | CPVC pipe exposed, 25 mm OD |
| 159 | CPVC pipe exposed, 32 mm OD |
| 160 | CPVC pipe exposed, 40 mm OD |
| 161 | CPVC pipe exposed, 50 mm OD |
| 162 | CPVC pipe concealed incl. chasing, 15 mm OD |
| 163 | CPVC pipe concealed incl. chasing, 20 mm OD |
| 164 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittingswith one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge25 mm nominal outer dia Pipes |
| 165 | G.I. pipe internal work, roof level, 25 mm NB |
| 166 | G.I. pipe internal work, roof level, 32 mm NB |
| 167 | G.I. pipe internal work, roof level, 40 mm NB |
| 168 | G.I. pipe internal work, roof level, 50 mm NB |
| 169 | G.I. pipe, 65 mm NB |
| 170 | Painting with synthetic enamel (two more coats) on new work |
| 171 | Gun metal gate valve, 25 mm NB |
| 172 | Gun metal gate valve, 32 mm NB |
| 173 | Gun metal gate valve, 40 mm NB |
| 174 | Gun metal gate valve, 50 mm NB |
| 175 | Gun metal NRV, 40 NB |
| 176 | Gun metal NRV, 50 NB |
| 177 | Gun metal NRV, 80 NB |
| 178 | Brass stop cock, 15 mm |
| 179 | Brass stop cock, 20 mm |
| 180 | Structural steel work (built-up sections, trusses, framed work) |
| 181 | Polyethylene water storage tank (ISI:12701), per litre |
| 182 | Butterfly valve (manual) 65 NB |
| 183 | Butterfly valve (manual) 80 NB |
| 184 | Nitrile rubber insulation 19 mm |
| 185 | GI pipes medium class, 80 mm NB |
| 186 | Brass ball valve PN-40, 15 mm NB |
| 187 | Brass ball valve PN-40, 20 mm NB |
| 188 | Brass ball valve PN-40, 25 mm NB |
| 189 | Motorised butterfly valve system for OHT filling – 50 mm dia NB Float Valve |
| 190 | Solar water heater 300 LPD (For Kitchen) |
| 191 | Electrical works |
| 192 | Wiring for light/fan/exhaust point with 1.5 sq.mm FRLS PVC cable in conduit (Group C). |
| 193 | Wiring for light/fan/exhaust point with 1.5 sq.mm FRLS PVC cable in conduit (Group B). |
| 194 | Wiring for light/power plug with 2×4 sqmm FRLS Cu + 1×4 sqmm earth in PVC conduit |
| 195 | Supplying & drawing of FRLS PVC insulated copper conductor, single core cable in the existing surface PVC conduit for 3x1.5sq.m |
| 196 | Supplying & drawing of FRLS PVC insulated copper conductor, single core cable in the existing surface PVC conduit for 3x2.5sq.m |
| 197 | Supplying & drawing of FRLS PVC insulated copper conductor, single core cable in the existing surface PVC conduit for 3x4sq.m |
| 198 | Supplying & drawing of FRLS PVC insulated copper conductor, single core cable in the existing surface PVC conduit for 3x6sq.m |
| 199 | GI box with modular plate & 5/6A socket + 5/6A switch |
| 200 | GI box with modular plate & 6 pin 15/16A + 5/6A socket with shutter & 15/16A switch |
| 201 | 3 pin, 5A ceiling rose on the existing junction box |
| 202 | Supplying & fixing angle holder including connections |
| 203 | Supplying and fixing stiff pendent with 300 mm long, 20mm dia x 1.6 mm thick steel conduit, aluminium cast back plate and brass holder complete, including wiring the down rod with 1.5 sq.mm FRLS PVC insulated, copper conductor, single core cable and painting |
| 204 | Call bell/buzzer, 230 V |
| 205 | Co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor, PE insulated, shielded with fine tinned copper braid and protected with PVC sheath |
| 206 | Medium class PVC conduit 25 mm with accessories (surface/recessed) |
| 207 | Medium class PVC conduit 32 mm with accessories |
| 208 | Supplying and fixing metal box of following sizes on in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required for 75mm x 75mm x 60mm deep |
| 209 | Supplying and fixing metal box of following sizes on in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required for 100mm x 100mm x 60mm deep |
| 210 | Supplying and fixing metal box of following sizes on in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required for 150mm x 75mm x 60mm deep |
| 211 | Supplying and fixing metal box of following sizes on in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required for 150mm x 150mm x 60mm deep |
| 212 | Modular switch/socket on existing modular plate & switch box including connections 5/6A switch |
| 213 | Modular switch/socket on existing modular plate & switch box including connections 15/16A switch |
| 214 | Modular switch/socket on existing modular plate & switch box including connections 3 pin 5/6A socket outlet |
| 215 | Modular switch/socket on existing modular plate & switch box including connections6 pin 15/16A socket outlet |
| 216 | Modular switch/socket on existing modular plate & switch box including connectionsTV antenna socket outlet |
| 217 | Modular switch/socket on existing modular plate & switch box including connections bell push |
| 218 | Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubical panel, making connections 100 A, 16 KA, TPMCCB |
| 219 | 75×75×10 mm zinc-passivated box with RJ45 socket for data point |
| 220 | SP&N MCB DB 8 way, double door |
| 221 | TP&N MCB DB 415V, 4 way (4+12), double door |
| 222 | MCB “C” curve SP 5–32A |
| 223 | Double pole 240V, isolator in the existing MCB DB for 40A |
| 224 | Double pole 240V, isolator in the existing MCB DB for 63A |
| 225 | Four pole 415V, isolator in the existing MCB DB for 40A |
| 226 | Cubical LT switchboard (IP52) with 100A 4P MCCB, meters, lamps, bus bars; outgoing 63A 4P MCB-6 Nos & 40A DP MCB-2 Nos |
| 227 | 2 module(100mm x 75mm) modular GI box with base & cover |
| 228 | 3 module(100mm x 75mm) modular GI box with base & cover |
| 229 | 6 module(200mm x 75mm) modular GI box with base & cover |
| 230 | 8 module(125mm x 125mm) modular GI box with base & cover |
| 231 | 12 module(200mm x 150mm) modular GI box with base & cover |
| 232 | Telephone tag block – 20 pairs |
| 233 | GI earth plate4.5 m long 40mm diawith enclosure, pipe, charcoal/salt etc. |
| 234 | 25×5 mm GI strip laid as strip electrode |
| 235 | Supply of LED street light fitting of 60 watt, AC 240 volts of make Crompton, catalog no. LSTP-60-CDL-M of NEXUS NEO LED |
| 236 | Exhaust fan double bearing self lubricating type, single phase, 50 cycles Light Duty Type |
| 237 | 500 V grade TPIC Bus Bar Chamber complete with 4 Nos copper iMRulator 100 Amp Capacity |
| 238 | Floor mounting cubical type dust & vermin proof electrical LT control panel board of the following specification made with 16 mm thick MS sheet built on MS angle iron frame work duly painted with 2 coats of power fray paints320 AMP TPN SDF with fuse |
| 239 | 10W LED Downlighter (recessed/surface), Al die-cast, ≥90 lm/W, 5-yr warranty |
| 240 | 22W LED Tubelight |
| 241 | 18W LED Tubelight |
| 242 | 2′×2′ 34W LED Panel |
| 243 | 10W LED Bulkhead |
| 244 | 305 mm, 1400 RPM exhaust fan with louver & bird guard |
| 245 | Ceiling fan complete with blades/downrod etc. – 1200 mm sweep |
| 246 | Installation, testing & commissioning of pre wired fluorescent/compact fitting incl. connection |
| 247 | Installation, testing & commissioning of ceiling fan incl. wiring of downrod |
| 248 | Two-module stepped electronic fan regulator |
| 249 | Laying of one number PVC insulated and PVC sheathed power cable of 1.1 KV grade Upto 35 sq.mm and upto 95 sq.mm |
| 250 | Providing and fixing lightning arrester rod with copper tape and GI pipe earth termination as per IS:2309 |
| 251 | Supplying, Installation, Testing and commissioning of 1200 mm sweep, Bee 5 star rated, ceiling fan with Brush Less Direct Current Motor, class of insulation: B, 3 nos blades, 30 cm long down rod, 2 nos canopies, shackle kit, safety rope, copper winding. |
