|
| 1 | Dismantling plain or corrugated steel sheeting any thickness, complete all as specified and directed. |
| 2 | Supply & Fixingfor Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/chadding to wall, fixed with self tapping screws complete all as specified and directed. |
| 3 | Supply & Fixingfor Pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/chadding to wall, ficed with self tapping screws as specified as in ridges complete all as specified and directed. |
| 4 | Supply & Fixing for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc..conforming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 5 | Taking down cement plaster including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. |
| 6 | M&L for rendering 15 mm thick in CM (1:4) on fair face of brick work surfaces finished even and smooth without using extra cement complete all as specified and directed. |
| 7 | Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc 15 cm thickness (below or above ground level)and removing unserviceable material outside cantt area complete all as specified and directed. |
| 8 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing unserviceble material out side cantt area complete all as specified and directed. |
| 9 | M&LforGlazed vitrified ceramic tiles 8mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchover 15 mm thick CM (1:6) cement mortar screed bed complete all as specified and directed . |
| 10 | M&L Granite (of any type) slab work, 18-20 mm thick(table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shadecomplete all as specified and directed . |
| 11 | M&L coloured Glazed ceramic tilesin vertical surface 300 x 450x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and directed. (Note renderibg/backing layer shall be measured and paid separately under respective items in this schedule). |
| 12 | M&L for non skid coloured ceramic tiles7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match compete all as specified and directed. |
| 13 | M&Lfor screed bed or bedding layer 15 mm thick in cement mortar (1:6) on floors for laying floor finish complete all as specified and as directed. |
| 14 | M&L 10 mm thick plastering in cement mortar (1:4)brick or on concrete surfaces of wall and finishing the surfaces fair and even without using extra cement all as specified and directed as in screed bed of tiles. |
| 15 | M&L 25 mm thick PCC 1:2:4 type B-0 using (12.50 mm graded stone aggregates) as in floor finished even and rough complete all as specified and as directed. |
| 16 | M&L 40 mm thick PCC 1:2:4 type B-0 using (12.50 mm graded stone aggregates) as in floor finished even and rough complete all as specified and as directed. |
| 17 | S&F in repairs Vitreous China wash basin, white, flat back, size 630x450mm with coupling excluding taps, waste, chain and plug andporcelainstopper but including brackets white incl 32mm dia 90cm long PVC waste down pipe, complete all as specified and directed. (Note : Contractor should resolve the complain within 24 Hrs and should give feedback to the Engineer in charge). |
| 18 | S&Fvitreous China Wash down water closet pan (Anglo indian type), white fixed with brass screwswith necessary connection with water line and sewer line etc. complete including S&FPlastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device for pedestal pan complete all as specified and directed including taking out old one. |
| 19 | S&F in repair Health faucet (ABS Body) mild steelchromium plated suitable for 15 mm diapipe with 1.25 metre long flexible tube and ABS wall hook including makingconnections and fixed in position completein all respect as specified. |
| 20 | S&F in repairs CP Pillar taps 15 mm bore, cast copper alloy, with capstan heads screwed down high pressure, with or without lettered `Hot\" or `Cold\" with long screwed shanks & fly-nuts, screwed for iron pipe, complete all as specified and directed. (Note : Contractor should resolve the complain within 24 Hrs and should give feedback to the Engineer in charge). |
| 21 | S&F in repairs 15mm cromium plated Bib taps, cast copper alloy with crutch orbutterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed. |
| 22 | S&F in repairs Stop valves 15 mm bore, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and directed. |
| 23 | S&F Soap dish, vitreous china white, approximate size 160 x 160 x 90mm complete all as specified and as directed. |
| 24 | S&F towel rail 600mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats all specified and directed by engineers in charge. |
| 25 | S&F for Stainless steel sink, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc., overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm complete all as specified and as directed. |
| 26 | S&F vitreous China urinals, bowl type, flat back of size 465 x 355 x 265 mm (minimum) white with grating and union for discharge pipe complete including providing and fixing plugs, bedding urinals against wall in CM (1:2), screwing urinal to plug etc. complete all as specified and directed by including taking out old one. |
| 27 | S&F for 10Ltr PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, complete all as specified and directed. |
| 28 | S&F for 450mm long PVC connections 15mm size with PTMT nuts, complete all as specified and directed. |
| 29 | S&Fin repair 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers , complete all as specified and directed. |
| 30 | Taking up or down 15mm dia steel tubing and connection including cleaning for re-fixing or removal to store complete all as specified and as directed. |
| 31 | Supplying and laying of 15mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. |
| 32 | Taking up or down 20mm dia steel tubing and connection including cleaning for re-fixing or removal to store complete all as specified and as directed. |
| 33 | Supplying and laying of 20mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. |
| 34 | Taking up or down 25mm dia steel tubing and connection including cleaning for re-fixing or removal to store complete all as specified and as directed. |
| 35 | Supplying and laying of 25mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. |
| 36 | S&F for 125/110 mm bore dia PVC (SWR) \"P’ trap, complete all as specified and directed. |
| 37 | S&F for Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms), complete all as specified and directed. |
| 38 | S&F PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed. |
| 39 | S&F PVC (SWR) bends any radius 110mm dia with access door, complete all as specified and directed. |
| 40 | S&F PVC (SWR), junction single, (Single T) equal or unequal 110mm dia with access door, complete all as specified and directed. |
| 41 | S&F in repair toilet paper holder, viterous china, box type white fixed to walls with chroium plated (cp) brass screws complete all as specified and as directed. |
| 42 | S&F PVC (SWR) vent cowl 110mm dia, complete all as specified and directed. |
| 43 | Dismantlingstructuralsteelworkin- cluding doors, gates but excluding framed truss etc.complete all as specified and as directed. |
| 44 | M&L for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified as directed. |
| 45 | Taking down chowkats or frames with shutter (without taking off shutter from the frames) n. exc 1.50 Sqm each complete all as specified and directed. |
| 46 | Taking down chowkats or frames with shutter (without taking off shutter from the frames) exc. 1.50 Sqm n.exc 4 Sqm each complete all as specified and directed. |
| 47 | S&F factory made solid PVC door Frame of size 50 mmx47 mm made out of 5mm thick wood grain printed PVC sheet and edges will be painted to match with printed sheet reinforced M.S. square tube, supplying & fixing in opening as per specification & drawing on page no. 160of SSR Part -II complete all as specifiedand directed. |
| 48 | S&F factory made solid panel PVC door shutter 30 mm thick style consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheets strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock rail and bottom rail on either side and as gap inside for top rail and bottom rail paneling of plain colour PVC sheet to be fitted in the MS frame welded/seated to the stiles and rail with suitable PVC sheet bending and jointed together with solvent cement supplying and fixing in the frame at site as per specification and drawing. |
| 49 | S &F for cast iron or mild steel, Hat and coat hooks, solid body, 175mm to 250 mm complete all as specifiedand directed. |
| 50 | S&F 2nd class hardwood plain solid, straight chowkat and frames, wrought, framed rebated on the solid, rounded or chamfered put together with glue pinned at joints all as specified inanddirected. |
| 51 | S&F 35 mm thick, 2nd class hardwood glazed and skeleton shutters, open rebated and prepare to receive gauge etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for secruing glass/gauge etc size of member of shutter as specified in SSR Part-I Section 8 Clause 8.20(a), fitted to chowkats complete all as directed. |
| 52 | S&F 35 mm thick flush shutters solid core construction, with particle board core and ply wood face panels commercial type on both sides complete all as specified and as directed. |
| 53 | M & L for preparation of old wood or wood based surface and applying one coats of synthetic enamel paint ,complete all as specified and as directed. |
| 54 | M & L Applying two coats of synthetic enamel paint on wood/wooden based surfaces over one coat of pink primer including preparation of new surfaces over 10 cm width or girth complete all as specified and as directed. |
| 55 | M&L preparation of new steel surface exc 10cm width or girth and applying two coats of synthetic enamel paints over one coat of red oxid zinc crome primer all as specified. |
| 56 | M&L preparation of old steel surface exc 10cm width or girth and applying one coats of synthetic enamel paints all as specified. |
| 57 | S&F Butt hinges, heavy weight, cold rolled mild steel, and fixed of size 100 mm complete all as specified and directed. |
| 58 | S&F Butt hinges, heavy weight, cold rolled mild steel, and fixed of size 75 mm complete all as specified and directed. |
| 59 | S & F alloy wire cloth 0.45 mm nominal dia of wire and avg width of appreature 1.40 mm and fixed with aluminium wire staples complete all as specified and as directed. |
| 60 | S & F in repair Door closer hydraulically regulated, designation No. 1 universal type, suitable for door shutters up to 700 mm in width and of weight not more than 35 kg and fixed Aluminium (extruded section)body complete all as specified as directed. |
| 61 | S&F for Floor door stopper 150mm of brass body and tongue with hard drawn steel spring aluminium alloy bodywith hard drawn steel spring, fixed in floor complete all as specified as directed. |
| 62 | S&F 200 mm long aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixingclips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as directed. |
| 63 | S&F 150 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed. |
| 64 | S&F Extruded aluminium alloy handles 150 mm long fabricated type anodised complete all as specified and directed . |
| 65 | Hacking out old broken glass (any thickness size, quality or description) from wooden frames or stone, concrete or brick surrounds glazed with putty or fixed with beads all as directed. |
| 66 | S&F sheet glass 4.0 mm thick ordinary quality and glazing with oil putty or wooden beads in square, rectangle n.exc 0.5 Sqm in each pan all as specified and as directed. |
| 67 | S&F for 19mm thk Block board, grade 2 quality, interior grade, commercial type decorative type, both faces complete all as specified and directed. |
| 68 | S&F for 12mm thk Particle board, medium density, flat pressed, single layer type or three layer type, BWR grade complete all as specified and directed. |
| 69 | S&F for 12mm thk Veneered decorative ply wood, grade I (with BWR resin) decorative veneers on both faces complete all as specified and directed. |
| 70 | S&F Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, screws etc. complete all as specified and as directed. |
| 71 | Providing and fixing factory made UPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Windowprofile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (Onevertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drillingof holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steelFrame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed tothe wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mmnominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured lorpayment purpose.) |
| 72 | S&F Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. but of anodised aluminium alloy andknobs complete all as specified. |
| 73 | Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium brass/ stainless steel screws, all complete as snap beading for glazing/ paneling, C.P. per architectural drawings and the directions of Engineer-in-Chief. |
| 74 | Supply only Liquid water proofing compound. |
| 75 | M&L Prepration of new surface of wall and Applying two coats of oil emulsion distemper including priming over a coat of 3mm wall putty complete all as specified. |
| 76 | M&L prepration of old surface of wall and applying two coats of oil emulsion distemper with priming over a coat of 3mm wall putty complete all as specified. |
| 77 | M&L preparation of old plaster surfaces and Applying two coats of Asure Radiance exterior Emulsion paint (7 year warranty)over one coat of Azura Premium Damp Arrestor alkali block dual primercomplete all as specified. |
| 78 | M&L preparation of newly plaster surface of wall and Applying two coats of Asure Radiance exterior Emulsion paint (7 year warranty)over one coat of Azura Premium Damp Arrestor alkali block dual primercomplete all as specified. |
| 79 | Demolition of existing RCCof any description and any postion not otherwise (reinforcement cut as required to facilate demolition) all as specified and directed. |
| 80 | S&F Rotational moulded polytehylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position of capacity 1000 ltrs incl. making connections including 25 mm dia bore Ball Valve high pressure of PTMT with epoxy coated Aluminum rod and high density plastic ball screwed for iron pipe and fixed. (Minimum wt -455 gms) complete all as specified and directed. |
| 81 | M&L 50 mm thick PCC 1:3:6 type C-1 (20 mm graded stone agg) as inplinth protection finished even and fair complete all as specified and as directed. |
| 82 | M&L forscreed bed 15mm thick in CM 1:4 onsurface or concrete surface finished even and rough for laying tiles complete all as specified. |
| 83 | M&L for Chequred cement concrete tiles 20 x 20 cm x25mm thick set jointed and pointed in neat cement slurry mixed with gray cement and pigment as in path all as specified and as directed. |
| 84 | S&F Curtain rod 20 mm dia Aluminium fancy type complete with clamps, ring, ball shaped knobs at both end, all golden colour, complete all as directed by Engr-in-charge. |
| 85 | Demolition & breaking up existing 150mm dia drain pipes(salt glazed stoneware, ac or reinforced concrete) pipe including PCC bed set in cement mortar & removing demolished material from site all as specified and as direted by Engr-in-charge. |
| 86 | M&L PCC1:3:6 type C2 (using 40 mm graded stone, aggregate) as in conncrete bed to drain pipes including packing under haunching against the sides of pipes after they are laid and tested for 150 mm dia SWG pipe all as specified and directed. |
| 87 | M&L MS TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia as reinforcement completeall as specified &directed. |
| 88 | M&L MS TMT bar 8 mm dia and over, upto and incl 10mm dia in stirrups , speces and binder complete all as specified and as directed. |
| 89 | Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed. |
| 90 | M&L brick work with sub class \"B\" bricks straight or curved in plan exc 6 mtr mean radius built in CM (1:6) using old size bricks complete all as specified and as directed. |
| 91 | M&L brick work with sub class \"B\" bricks straight or curved on plan to any radius in half brick thick wall built in CM 1:4 complete all as specified and directed. |
| 92 | Dismantling of 100 mm dia cast iron drain pipes, jointed in cement mortar and taking outold pipe complete all as specified and directed. |
| 93 | S&F PVC (SWR) 110 mm bore pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors as specified and directed. |
| 94 | S&F 110 mm bore PVC (SWR) bends any radius complete all as specified and directed. |
| 95 | M&L forRCC (nominal; mix), type B0 1:2:4 (using 12.5mm graded crushed stone aggregate) as in chajaa supported on wall, beams, columns, in floor, roof, landing, deck slab and in shelves and the like complete all as specified. |
| 96 | M&L formm work to Chullah hoods, chajjas troughs and similar items including edgs complete all as directed. |
| 97 | S&F for PVC wall panelling 10mm thick including pasting , beading and aliied services as per manufacturer instrucion / requirement at site complete all as specified and directed by Engr in Charge .(Make : Polywood and equivalent ) |
| 98 | M&L pre-cast reinforced cement concrete (1:2:4) type B1(using 20 mm graded crushed stone aggregate) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain facesetc set in CM 1:6 including necessary forms, moulds etccomplete all as directed . |
| 99 | S&F SS mild steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4 mm and fixed with stainless steel wire staples all as specified. |
| 100 | Dismantling ceiling boards any thickness incl cover fillets complete all as specified and as directed by the Engr-in-Charge |
| 101 | S&FPVC fluted wall/Ceillingpanelling section of size 10mm X 300mm with wall thickness of 0.80mm±0.2mm (per Sq mtr). Weight is 4.90kg±4%), each section consist of 10 groves equidistant at 25mm of 4mm depth and a width of 5mm complete all as specified and as directed. |
| 102 | Material and labour Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified ® complete all as specified and as directed. |
| 103 | M&L for planting and developing lawn grass (phospolen) includingPreparing of soil base by excavation / ploughing and loosening of ground upto 15cm and removing unwanted material, grass stone etc to a distance exceeding 50m but not exceeding 250m complete all as specified and as directed. |
| 104 | S& fix in repair block board 18/19MM thickexterior grade, including sanmica pasting both side fixed with screws to timber frame work in cup board for short area including 40mm dia knob and magnet catch complete all as specified and as directed by Engineer-in-charge. |
| 105 | Taking down carefully the existing aluminium/copper point wiring of any size and capacity and type by disconnecting from the either terminals complete including fittings and fixtures such as switches, sockets, ceiling rose, fanregulators, lamp holders, call bell, bell pushesany type etcby unscrewing and taken away from site complete and make good the disturbed surface as existing. Note :(i) cost of unserviceable materials will be charged from the contractor against schedule of credit. (ii) Serviceable light fitting shall be kept in safe custody for reuse at site. (iii) Re-fixing shall be measured and paid seperately. |
| 106 | M&L for Concealed point wiring with 1.5 sqmm PVC insulated FRLSH sheathed 1100 Volts grade copper multi stranded conductor drawn through and including rigid PVC conduit 20 mm dia concealed in walls ,roofs, etc including 1.5 sqmm PVC insulated copper conductor as earth continuity conductor and other accesories such as metal box, sheet cover, screws,nuts etc connecting it to the common earth dolly all as specified for one light/ceiling fan/Exhaust fan / wall fan each controller by one way switch.Note :- (i) One run of PVC conduit, two runs of cable (Phase + Neutral) and one run of earth wire shall be measured and paid as one unit.(ii) Quoted rate shall deemed to be incluive oflaying of conduit and making good the surface as per existing.(iii)Necessary chase cutting if any shall be in the quoted rate. |
| 107 | All as per item no 106 abovebut one 3 pin 5 Amps socket outlet on same board controlled by one switch complete all as specified and as directed |
| 108 | All as per item no 106 abovebut one 3 pin 5 Amps socket outlet independent controlled by one switch complete all as specified and as directed |
| 109 | All as per item no 101 above above but with 2.5 sqmm cable copper for 15/16 Amps socket outlet on independent board,including 2.5 sqmm copper conductor PVC insulated sheathed continuous earth wire and connecting to common earth dolly complete all as specified and directed. |
| 110 | All as per item no101 above but with 4.0 sqmm cable copper for 15/16 Amps AC point on independent board,including 4.0 sqmm copper conductor PVC insulated sheathed continuous earth wire and connecting to common earth dollycomplete all as specified and directed. |
| 111 | All as per item no 101 above butforone bell/buzzerpointcontrolled by one bell push button on the same board with other switches or independent with 1.5 Sqmm copper conductor cables complete all as specified and as directed |
| 112 | Taking down unserviceable submain wiring any size,complete all as specified and directed. |
| 113 | Supply and fixing sub-main/sub-circuit wiring with PVC insulated & unsheathed two run of 4 Sqmm single core multi stranded copper conductor cable (FRLSH), 1100 Volt grade alongwith one run of4 Sqmm PVC insulated & unsheathed copper conductor cable (FRLSH), 1100 Volt grade, connected to common earth dolly asearth continuity conductor, drawn through 20 mm conduit with all accessories and PVC rectangular boxes for mounting switch socket and fan regulator etc including taking down existing sub main wiring complete all as specified and as directed.Note :- (i) One run of PVC conduit, two runs of cable (Phase + Neutral) and one run of earth wire shall be measured and paid as one unit.(ii) Quoted rate shall deemed to be incluive oflaying of conduit and making good the surface as per existing.(iii)Necessary chase cutting if any shall be in the quoted rate. |
| 114 | Supply and fixing sub-main wiring with PVC insulated & unsheathed two run of 6 Sqmm single core multi stranded copper conductor cable (FRLSH), 1100 Volt grade alongwith one run of6 Sqmm PVC insulated & unsheathed copper conductor cable (FRLSH), 1100 Volt grade, connected to common earth dolly asearth continuity conductor, drawn through 20 mm conduit with all accessories and PVC rectangular boxes for mounting switch socket and fan regulator etc including taking down existing sub main wiring complete all as specified and as directed.Note :- (i) One run of PVC conduit, two runs of cable (Phase + Neutral) and one run of earth wire shall be measured and paid as one unit.(ii) Quoted rate shall deemed to be incluive oflaying of conduit and making good the surface as per existing.(iii) Necessary chase cutting if any shall be in the quoted rate. |
| 115 | M & L for 1 X 20 wattextruded aluminium housing LED lighting fixture with Lamp Lumen not less than 2100 lumen polycarbonate ,enviornmental friendly ,energy efficient fixed to wall/ ceilling & connecting upto ceiling rose with three core twisted flexible 1.5 sqmm PVC copper conductor cable with earthing complete all as specified and as directed |
| 116 | Supply and fix LED batten 10 Watt extruded aluminium housing,high power diffuser, slim and integrated design, lumen not less than 2100 lumen polycarbonate, energy efficient fixed to wall/ ceilling and connecting upto ceilling rose with three core twisted flexible 1.5 sqmm PVC copper conductor cable with earthing complete all as specified and as directed. |
| 117 | Supply and fixedenergy efficient LED Square light of 600x600 mm 36 Watt including driver complete all as specified and directed. |
| 118 | Supply and fixing LEDbldg street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed |
| 119 | M & L Switch Modular type single pole, one way 6 Amp complete all as specified and as directed |
| 120 | S & F modular socket 6 Amps, 5 pin, 240 Volts, two modules conforming to IScomplete all as specified and as directed. |
| 121 | S & F modular socket 6/16 Amps, 3 pin, 240 Volts, two modules conforming to IScomplete all as specified and as directed. |
| 122 | M & L Modular Bell push 6A 1 module complete all as specified and as directed |
| 123 | S & F modular switch 16 Amps, 240 Volts, single pole, one way, single module conforming to IScomplete all as specified and as directed. |
| 124 | S & F Modular Fan step regulator, 120W - 2 modulecomplete all as specified and as directed. |
| 125 | S & F Modular White cover plate with frame 1/2 M incl taking down old onecomplete all as specified and as directed. |
| 126 | S & F Modular White cover plate with frame 3 M incl taking down old onecomplete all as specified and as directed. |
| 127 | S & F Modular White cover plate with frame 4 M incl taking down old onecomplete all as specified and as directed. |
| 128 | S & F Modular White cover plate with frame 6 M incl taking down old onecomplete all as specified and as directed. |
| 129 | S & F Modular White cover plate with frame 8 M incl taking down old onecomplete all as specified and as directed. |
| 130 | S & F Metal flush box 1/2 module incl taking down old onecomplete all as specified and as directed. |
| 131 | S & F Metal flush box 3 module incl taking down old onecomplete all as specified and as directed. |
| 132 | S & F Metal flush box 4 module incl taking down old onecomplete all as specified and as directed. |
| 133 | S & F Metal flush box 6 module incl taking down old onecomplete all as specified and as directed. |
| 134 | S & F Metal flush box 8 module incl taking down old onecomplete all as specified and as directed. |
| 135 | S & F ceiling rose 3 terminal PVC/polycarbonate isolated body typecomplete all as specified and as directed. |
| 136 | Supply and fixing Ac motor starter 2 modular with red and green switch complete with connection testing and commissioningcomplete all as specified and as directed. |
| 137 | S & F Buzzer, Ding Dong AC. 230 volts, single polecomplete all as specified and as directed. |
| 138 | Supply and fixing SP 6-32 amp rating 240V, 10KA \"C\" curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioningcomplete all as specified and as directed. |
| 139 | Supply and fixing SPN 40-63 amp rating 240V, 10KA \"C\" curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioningcomplete all as specified and as directed. |
| 140 | Supply and fixing TPN MCB100 Amp rating 415V, 10 KA in DB complete with connection testing and commissioningcomplete all as specified and as directed. |
| 141 | Supply and fix 4 way SPN Double door DB with 100 amps rated bus barcomplete all as specified and as directed. |
| 142 | Supply and fix 8 way SPN Double door DB with 100 amps rated bus barcomplete all as specified and as directed. |
| 143 | Supply and fix 4 way TPN Double door DB with 200 amps rated bus barcomplete all as specified and as directed. |
| 144 | Taking down ceiling fan/ exhaust fan/wall fan, cealing cable end, dismantling blades and removing fan and blades to store Complete all as specified and directed. |
| 145 | Servicing ofceiling fan/ exhaust fan/wall fan incl open all parts, lubrication, cleaning and other necessary job to make smooth run of the item Complete all as specified and directed. |
| 146 | M & L for Spray Painting of ceiling/ wall fans and Exhaust fan complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etccomplete all as specified and as directed. |
| 147 | Refixing ceiling/ wall fansand connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and directed. |
| 148 | Re-Fixing only exhaust fan (M.D. supply) and connecting up including provision of cable from ceiling rose/connector to fan complete all as specified and directed. |
| 149 | Fixing only serviceable LED light fitting of any type and any watt retrievied from item No 105 above complete all as specified and directed. |
| 150 | M&L for Earthing complete with galvanised steel earth plate electrode 600x600x6mm thick buried directly in ground (earth pit not less than 2.25mtrs deep below ground level) with top edge of plate not less than 1.5mtrs below normal ground level, connected to GI earth wire 4 mm dia by means of bolts,nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 connected to earthing test point on completion with and including 15mm bore medium grade GI protection pipe (upto 7.5mtr long) for earth and 20mm GI medium grade for watering including PCC chamber pit & cover with suitable lifting hooks, with funnel, wire mesh, common salt, charcoal filling, necessary excavation and earth work in any type of soil complete all as specified and directed by Engr-in-Charge. |
| 151 | M&L for earth continuity conductor or main earthing lead galvanised iron wire of size 4mm fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. completecomplete all as specified and as directed. |
| 152 | Materials and labour for inrepair galvanized iron Tubing light grade of size 40 mm dia for cable passingetc all as specified and directed |
| 153 | Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded,galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100Volts grade with stranded aluminium conductor of size 35.0 sq mm 3.5 core in trenches / through GI pipe / fixed along with pole structure etc with all fixing & connecting accessories complete all as specified and directed by Engr-in-Charge. |
| 154 | M&L for excavation in trenches n.exc.1.5 m wide and n.exc. 1.5 m in depth for foundation etc n.exc. 10 sqm on plan and n.exc 1.5 m in depth and getting out in soft/loose soil complete all as specified & directed. |
| 155 | Materials and labour for sand filling around the cable with approved quality coarse sand for sand cushioning of Under ground cableincludingspreading and punning down to desired thickness complete all as specified and as directedby the Engr-in-Charge. |
| 156 | Supplying and laying un-reinforced precast concrete cable cover, class LV, type 1 with flat, size 250mm x 150mm x 40mm complete specified and directed. |
| 157 | M&L for returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft loose soil complete all as specified & directed |
| 158 | M&L for removing excavated material n, exc. 50 m and depositing outside MD land at a level n exc. 1.5 m above the starting point complete all as specified & directed |
| 159 | Supply and laying GI pipe light grade (ISI Marked) of size 40 mm for cable protection to be fixed on wall /pole /road crossing with necessary clamps complete all as directed and specified by Engr-in-Charge.Note :- Unit rate quoted is deemed to be inclusive ofclampsalong with all fittings etc. if required to be fixed the pipe. |
| 160 | Material and Labour for Cutting existing steel tubing of size upto 50 mm for alterations or additions or for insertion of new tees, brances complete all as specified and directed by Engr-in-Charge. |
| 161 | Supply & lay pipe of size 25mm dia, galvanized, \"Medium Class\",incl fittings complete all as specified and directed by Engr-in-Charge. |
| 162 | Supply and fix 25mm dia Gate valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed |
| 163 | M&L for road cutting/PCC/Drain or under boaring for passing of pipes and make correct the top surface as per ground requirement. |
