|
| 1 | Dismantling floor, stone, hearth or wall tiling including cement mortar bedding but not backing, removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engr-in-charge. |
| 2 | M&L for 25 mm thick PCC 1:2:4Type B0 (12.5mm Graded Stone Aggregate) as in sub flooretc., including rough top surface to receive floor finish complete all as specified and as directed. |
| 3 | M&L for non skid coloured glazed ceramic tiles of any shade any pattern of size (pattern consist of combination of two or more colour 7 to8 -10mm(square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqmset and jointed in neat cement slurry and pointed in colour cement as in floor over and including 15 mm thick screed bed or bedding layer of cement mortar 1:6 complete all as specified and directed by Engr-in-charge.(No extra cost shall be allowed forremoving and refixing joinery and cuttingof doors etc, any required during executionwork |
| 4 | Material and Labour for glossy finish coloured vitrified ceramic tiles 8-10 mm thick of area of each tiles not exceeding 0.42 sqm but not exceeding 1.0 Sqm, of any shade of any pattern (pattern consists combination of two or more tiles ) as in vertical surfaces etcjointed in neat cement slurry and pointed in colored cement to match colour tiles over and including 10mm thick screed bed in CM 1:4 and pointed in coloured cement to match coloured tiles complete all as specified and as directed. |
| 5 | Material and Labour for vitrified ceramic tiles 8-10 mm thick dark shade/double charged/ultrachargedarea of each tiles not exceeding 0.42 sqm but not exceeding 1.0 Sqm, of any shade and any pattern (pattern consists combination of two or more tiles ) as in floor etcjointed in neat cement slurry and pointed in colored cement to match colour tiles over and including 15mm thick screed bed in CM 1:6 and pointed in coloured cement to match coloured tiles complete all as specified and as directed.NOTE: No extra cost sahll be allowed for Removing and re-fixing and necessary cutting of door etc if any required during execution of work. |
| 6 | S & F for 10 mm thick Vitrified light shade Coloured tiles, square/rectangular double polished, area of each tile n.exc. 0.36 sqm,in floor including 15mm thick screed bed in CM 1:4 etc.,set and jointed in neat cement slurryand pointed in white with pigment to matchfor laying floor finishes all as specified and as directed . |
| 7 | M&L for 8 to 10 mm thick ceramic joint free Coloured Tiles, of size 600x100/150mm, on vertical surface/Skirting over and including 10mm thick rencering in CM 1:4 Laid and Jointed in Neat Cement Slurry and Pointed in white cement with pigment to match the shade of the Tiles, complete all as specified and as directed. |
| 8 | M&L forcut kota stone slab ,flooring 20-25mm thick over cement screed bedbase laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone slab including rubbing and polishing and including 20mm thick screed bed CM 1:3 complete all as specified and as directed |
| 9 | Allas per item no 8 here in -beforebut in skirting,dado and steps risers including rubbing and polishing and including 10 mm thick back coat CM 1:3 complete all as specified and as directed complete all as specified and directed |
| 10 | M&L for 18 to 20 mm granite slab of any size for counter top and similar work over and including 15 mm thick screed bed or bedding layer ofcement mortar 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including making good the edges complete all as specified and directed by Engr-in-charge. |
| 11 | Demolition of brick work or stone masonary built in cement mortar including all quoins, arches, pillars etc.complete all as specified and directed |
| 12 | M&L for precast cement concrete hollow solid blocks exc 10cm widthMasonry type1:3:6 (16 mm using aggregate as per IS 383) set in cement mortar 1:6 all as specified and as directed by engineer in charge |
| 13 | M&L for precast cement concrete solid building blocks or slabs 10mm thick typeC1,1:3:6 (20 mm Aggregate) in walls set in cement mortar 1:6 all as specified and as directed by engineer in charge |
| 14 | M&L for HCRM TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bendin spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified |
| 15 | M&L TMT bars 5 mm and over upto and incl 10mm dia in stirrups, spacers and binders cut to length bent to shape required including bending, hooking binding with and incuding MS wire not less than 0.9 mm dia. |
| 16 | M& L for use and waste of Formwork to sides and soffits of floor or roof beams, beam haunchings,girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. flat and rough finished surface of concrete. |
| 17 | M&L for RCC1:2:4 type B1 using 20 mm graded aggregate as in concrete for slab supported walls, landing ,canopies and shalfs all as specified and as directed by engineer in charge |
| 18 | Taking down cement plaster alongwith tiles on brick or stone wall surfaces including raking out joints, hacking for key and scrubbing down with water complete all as specified and directed by Engr-in-charge. |
| 19 | M&L for rendering 15 mm thick in cement mortar 1:6 on other than fare face of brick work or concrete surfaces and finishing the surface even & smooth without using extra cement on any height complete all as specified and directed by Engr-in-charge. |
| 20 | M&L for rendering 15 mm thick in cement mortar 1:4 on other than fare face of brick work or concrete surfaces and finishing the surface even & smooth without using extra cement on any height complete all as specified and directed by Engr-in-charge. |
| 21 | M&L for rendering 10 mm thick in cement mortar 1:3 on other than fare face of brick work or concrete ceiling surfaces and finishing the surface even & smooth without using extra cement on any height complete all as specified and directed by Engr-in-charge. |
| 22 | M&L for applying two coat of Distemper oil emulsion by Auto Roller over a coat of primer over 2 to 3 mm thick birla putty punning including finishing bySanding Machine and Auto Roller new plaster surface complete all as specified or as directed by Engineer-in-charge.Make: Asian Paint (Tractor)/Berger paints (Bison super) |
| 23 | M&L for preparingold distemper and painted surfaces of walls including washing rubbing down andbrooming down smoke soot mould mass and applying one coats of Oil emulsion distemper old surface complete all as specified and directed by Engr-in-charge. |
| 24 | M&L for preparingold distemper and painted surfaces of ceilingincluding washing rubbing down andbrooming down smoke soot mould mass and applying one coats of Oil emulsion distemper old surface complete all as specified and directed by Engr-in-charge. |
| 25 | M&L for applying two coat of exterior Acrylic emulsion paint (100% acrylic) of approved colour and shade over a coat of primer and over 1 to 2 mm thick birla putty punning including preparation of new plastered surface complete all as specified and as directed by Engineer-in-charge. Make-Asian (Apex Ultima) paints/Berger (Whether coat long life) including necessary scaffolding . |
| 26 | M&L for preparing old external plaster surface of walls including washing rubbing down and brooming down mould mass and applying one coat of exterior Acrylic emulsion paint (100% acrylic) of approved colour and shade over a coat of primer and over 1 to 2 mm thick birla putty punning complete all as specified and as directed by Engineer-in-charge. Make-Asian (Apex Ultima) paints/Berger (Whether coat long life) including necessary scaffolding upto 2th floor. |
| 27 | Taking down chowkats or frame with shutter (without taking out shutter from the frame) not exceeding 1.50 Sqm each as doors, windows & ventilators etc. and removal from site complete all as specified and directed by Engr-in-charge. |
| 28 | Taking down door frame with shutter of area exc 1.50 but n exc 4.0 Sqm each and removing to store complete all as specified and as directed. |
| 29 | M&L Second class hard wood plain solid straight chowkat &frame wrought rebated on solid rounded, complete all as specified and directed. |
| 30 | M&L for 2 nd class hard wood plain cover fillets square rectangular or triangular in section bull nosed spayed chamfered or rounded on one edge or face sectional area exc 06 n, exc 13sqcm complete all as specified and directed by EIC |
| 31 | S& F cast brass powder coated Box type decorative door handle of 100mm long complete all as specified and directed by EIC |
| 32 | S & F in repair of 35 mm thick IInd class HW plain framed flush shutterboard with commercial veneered on both faces.The size of rail as per IS: 1003 (part-I), kiln seasoned & chemically pressure treated all as spd. |
| 33 | S & F 35 mm thick IInd class hard wood glazed or skeleton shutters, open rebated and prepared to recieve glass, gauge etc. (without sash bars) , edges of framing plain, chamfered or rounded, fitted with cut and mitred bead for securing glass etc,. Sizes of member of shutters as specified in SSR Part-I,1991, section 8, clause 8.20(a),complete all as specified and directed. |
| 34 | S&F in repair of 4 mm thick sheet glass for window/ventilators ordinary quality and glazing with rubber beading/oil putty in square exc 0.50 Sq.m in each pane complete all as specified and as directed. |
| 35 | S&F for stainless steel wire cloth 0.36 mmnominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples and including dismantling of old mesh complete all s specified and directed by EIC |
| 36 | S&F inrepair of continious(piano)hingesMS bright finish or electrogalvanised 30 mm width of flaps(when open) |
| 37 | M&L for 18/19 mm thick solid ply wood grade BWR type BB over head rack workfixed with decorative mica with both sides adhesive and nails for working table/storage almirah/doors etc fitted in wall in a any shape and in any direction etc to the reuired size and desire pattern and colouras specified and directed by EIC |
| 38 | M&L 12 mm thick plywood grade BWR type BB fixed with adhesive and nails foralmirah/doors etc fiited in wall in a any shape and in any direction etc to the reuired size and desired pattern and colour as specified and directed by EIC |
| 39 | S&Ffor knobs for cub board fixed in nut screw and washers of brasscomplete all as specified anddirected |
| 40 | S&F for colour powder coated aluminiumframe for, doors ,windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed by Engr In Charge |
| 41 | S&Ffor aluminium colourpowder coated window ,ventilatorof sliding shutter of sectios weighting 0.55 kg/m includingnecessary joining cleatsglazing clips rubber packing aluminium snap beading screws anodised aluminiu fittings such as peg stays 150 mm longs 01nos suitable handles 01 Noscomplete all as specified and as directed. |
| 42 | S&F Solid PVC Door Frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S. Square tube in opening as per specification & drawing mentioned in SSR complete all as specified and directed by Engr-in-charge. |
| 43 | S&F for 30 mm thick factory made solid panel PVC door shutter confirming to criteria of testing as per IS : 4020, consisting of frame made out of MS tube of 19 gauge thickness & size 19x19mm for stiles and 15x15 mm for top & bottom rails MS frames shall have a coat of red oxide primer of approved make and shall be covered with 5mm thick heat moulded PVC `C\" channel of size 30x50mm forming styles and 5mm thick 75 mm wide PVC sheets for top rail lock rail and bottom rail on either side and 10 mm (5 mm x 2) thick 20mm wide cross PVC sheet as gap insert for top rail and bottom rail paneling of 5 mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rail with 30 mm wide x 5 mm thick PVC sheet beading on either side and joined together with solvent cement, adhesive and an additional 5 mm thick PVC strip of 20 mm width is to be struck on the interior side of \"C\" channel using PVC solvent adhesive complete as per manufacturers specifications & drawings and complete all as specified and directed by Engr-in-charge. |
| 44 | S&F forhasp and staples 100mm long alluminium anodised complete all as specified and directed |
| 45 | S&F for100mm extruded brass handles, fabricated type poished |
| 46 | S&F forbrass100 mm long Butt hinges Type-21 with galvanised mild steel screws complete all as specified and directed by Engr-in-charge. |
| 47 | S&F in repair of aliminium anodised barrel tower bolts, 100 mm long complete all as specified and directed by Engr-in-charge. |
| 48 | S&F in repair of brass flush bot type 2 tower bolts, 100 mm longfixed flush complete all as specified and directed by Engr-in-charge. |
| 49 | S&F in repair of aluminium die cast of door closer hydraulically regulated designed No 3 universal type suitable for doorshutter size of 850mm to 1000mm in width weight between from 61 to 80kg and fixed |
| 50 | S&F in repair decorative end Knob for curtain rod 25mm dia fancy type as directed. |
| 51 | S&Fstain less steel Decorative curtain Rod 25mm dia with bracket and fixed in repair |
| 52 | S&F in repairs 250 mm brass, sliding door bolt with hasp, staple (Bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or brass bolt and fixed complete all as specified and directed by Engr-in-Charge. |
| 53 | M&L for preparation of new wooden surfaces of any description, not otherwise described, over 10cm width or grith and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-Charge. |
| 54 | M&L forFalse ceiling with 12mmthick 1.2m x 1.80m plaster of paries sheets fixed with machine screws on and including G I channel 22 guage thick grid work main joints placed at 1.20m centre to centre cross joints placed at 450mm centre to centre, hanging with 22 gauge GI strip suspenders fromroof \"J\" hooks bolts and nuts etc and treating the POP sheets with thin layer of POP with gypsum and hydrous binder and prepare the surface till smooth surface is achieved and applying two coat ofoil boud distemper of any patterrn and design over a coat of texture primer on ceilings sheets all complete as required as per manufacture\"s instructions and directed by the EIC1. The pattern and design shall be as directed by Engineer in charge during the execution of work.2. The exposed surface of the false ceiling shall be joint less even and smooth to receive two coats of oil bound distemper3. The POP sheets shall be fixed with suitable screws below the grid and shall not be placed over the grid |
| 55 | S&F of bevalled frameless wall mounted mirror of selected qualityfixed with wall bolting arrangement of size 600x450mm of good finish complete all as specified and directed. |
| 56 | S&F in repair1000 ltrs rotational moulded polyethylene three layered water with EPI coated storage tanks (cylindrical vertical with closed top) hoisted and fixed with all necessary fittings i in position includingtaking down existing water tank of 500 to 1000ltrs or removing of existing RCC old tankcomplete all as specified and directed by Engr-in-charge . |
| 57 | S&F25 mm dia bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed complete all as specified and directed by Engr-in-charge. |
| 58 | Taking up or down existing steel tubing/PPR pipe of 15mm dia bore of any grade and connections including making good the disturbed surfaces complete all as specified and directed by Engr-in-charge. |
| 59 | Taking up or down existing steel tubing/PPR pipe of 20mm dia bore of any grade and connections including making good the disturbed surfaces complete all as specified and directed by Engr-in-charge. |
| 60 | S&F for 20mm dia CPVC SDR 11 pipefixed to concealed/wall, ceilling,laid in floor etc incl all fittings with solvant and brass threaded fittings for fixing taps etc , including wtar tighteness test etc., complete all as specified and as directed. |
| 61 | S&F for 25mm dia CPVC SDR 11 pipe fixed to concealed/wall, ceilling, laid in floor etc incl all fittings with solvant and brass threaded fittings for fixing taps etc, including water tightness test complete all as specified and as directed. |
| 62 | S&F in repair 15 mm dia bore CP Bib cock, cast copper alloy, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipes or for union and fixed complete all as specified and directed by Engr-in-charge. |
| 63 | S&F in repair 15 mm dia bore CP two in one bib cock, cast copper alloy, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipes or for union and fixed complete all as specified and directed by Engr-in-charge. |
| 64 | S&F in repair 15 mm dia bore stop valve, cast copper alloy, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipes or for union and fixed complete all as specified and directed by Engr-in-charge. |
| 65 | S&F in repairs 15 mm dia bore cast copper alloy chromium plated fancy type angle cock with long shank & cup (concealed type) complete all as specified and directed by Engr-in-charge. |
| 66 | S&F in repairvitreous china wash hand basin, white, semi circular ,corner WHB fancy typeofsize 500 mm x 400 mm fixed over counter top including32 mm dia, brass waste coupling and including fixing of tap, waste fitting and union complete all as specified and directed by Engr-in-charge. |
| 67 | S&F in repair PVC connection 15 mm dia and 450 mm long with both end brass fly nutcomplete all as specified and directed by Engr-in-charge. |
| 68 | Supply and fix in repair 15 mm dia bore pillar taps swan neck cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered ‘Hot’ or “cold’ with long screwed shank and fly nuts, screwed for iron pipe and fixed complete all as specified and directed by Engr-in-charge. |
| 69 | S&F in repair 32 mm bore of pipe low density (LDPE) of pressure rating 6 Kg per Sqcm fixed to wall or floor etc including fittings complete all as specified and directed by Engr-in-charge. |
| 70 | M&L PCC 1:3:6 type C-1 using 20 mm graded stone aggregate for filling in bed block of hold fast etc complete all as specified and as directed. |
| 71 | S&F in repair stain less steeltowel rail of 20 mm dia D type, 60 cm long between flanges complete all as specified and directed by Engr-in-charge. |
| 72 | S&F in repair 100 mm dia cast iron floor trap with grating including jointing to waste pipe in run lead fixed in concrete type B1 1:2:4 completeall as specified anddirected |
| 73 | S&F forglass shelfassembly consist of 5.5mm thick sheet glass shelf 12cm wide with cromium plated bracket guard and railing 60cm fixedl with screws and making good surface of wall complete all as specified and directed by Engr-in-charge. |
| 74 | S&F for 125 mm fancy type shower rose brass chromium plated with CP arms for 15mm bore GI pipe complete all as specified and directed by Engr-in-charge. |
| 75 | S&F forbrass chromium plated bottle trap of32mm bore for wash hand basin with inlet and outlet and screwed for pipe or fixed complete all as specified and directed by Engr-in-charge. |
| 76 | Supply only 32mm dia waste fitting brass chromium plated for basin with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed by Engr-in-charge. |
| 77 | S&Ffor CP Health Faucet, (CP body)mild syteel chromium plated suitable for 15mm dia pipe with 1.25metre long flexible tube and ABS wall hook including making connections and fixed in position of any description, complete as all specified and directed. |
| 78 | S&F for Soap Dish, Single, as Approved, fixing with Brass Chromium Plated Screws including Taking down unserviceable Soap Dish of any description, complete as all specified and directed. |
| 79 | Supply and fix vitreous china premium 1st quality washdown water closet wall hung single piece EWC white /ivory/off white (closed pattern including all necessary accessorieswith PP soft close seat cover, hinges, Dual flush cistern, fitting, Make Jaquar or eqilent complete as all specified and directed. |
| 80 | S&F in repairs 10 ltrs capacity PVC low level flushing cistern white with inlet, float valve and handle including bracket with 32 mm dia PVC pipe 600 mm long complete all as specified and directed by Engr-in-charge. |
| 81 | Supply and fix Toilet paper Roll Holder with flat recessed typestainless steel complete all as spdand directed Make Jaquar 1151N |
| 82 | Removal of debris/malwa to a distance exc 1.5Km but n exc 5 Km and depositing out side the MD land and asdirected by Engr-in-charge. |
| 83 | Supply and fix PVC pipe (SWR) single socketed in any length with rubber ring joint 110mm dia fixed to wall complete all as specified and as directed. |
| 84 | Supply and fix PVC (SWR) bends 110mm with access door complete all as specified and as directed. |
| 85 | Supply and fix in repairs 110mm PVC (SWR) branch piece , single (Single Y) equal or unequal all as specified and as directed. |
| 86 | Supply and fix in repairs 110mm PVC (SWR)Junction , single T (SingleTY) equal or unequal all as specified and as directed. |
| 87 | S&F liquiled soap container of PTMT fixed with including chromium plated brass screws and wooden plastic cleats (Min weight 105gms) complete all asspecified and directed |
| 88 | M & L for point wiring with PVC insulated unsheathed multistranded copper conductor cable 1100 volt grade, FRLS of size 1.5 Sqmm drawn in and including PVC rigid conduit of size not less than 20mm dia with accessories (concealed) including modular metal flush box of suitable size with inner and outer white plastic plate (same make of switch and socket) including continues 1.5 Sqmm copper conductor (multistranded) PVC insulated and unsheathed cable earth wire to common earth and connected to earth dolly complete all as specified conforming to IS-694 for the following:- One light point controlled by one switch 6 Amps |
| 89 | All as per item no. 88 butOne fan/ exhaust point controlled by one switch 6 Amps |
| 90 | All as per item no. 88 but One 3 pin socket outlet 6 Amps on Independent board |
| 91 | All as per item no. 88but One 3 pin socket outlet 6 Amps on same board |
| 92 | All as per ser item no 88 but here-in before with 4 Sqmm PVC insulated copper conductor incl 4 Sqmm PVC copper conductor used as earth wire for power point /AC point on independent board |
| 93 | Supply and fixing of Modular Switch, one way, 6 Amps complete all as specified and directed |
| 94 | Supply and fixing of Modular Switch socket outlet 3 pin 5 amp flush type 3 module complete all as specified and directed |
| 95 | Supply and fixing of Modular Switch socket combination 16 A, 6 pin, 3 module complete all as specified and directed |
| 96 | Supply and fixing LED lights fitting 1x 18 W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose completeMake: Havells/ Bajaj/Crompton/Wipro/Philips/Luker. |
| 97 | Supply and fixing LED lights fitting mirror type2\"x 10W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose completeMake: Havells/ Bajaj/Crompton/Wipro/Philips/Luker. |
| 98 | Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m |
| 99 | Supply and fixing of ceiling rose in poly carbonate 3 plates flush type 6 amps, 250 volts AC complete all as specified and directed. |
| 100 | Taking down ceiling fan, dismantling blades and removing fan to store, Painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. (M & L) including hanging of ceiling fan connectingup incl provn of cable from Ceiling rose to fan cmplete all as directed |
| 101 | S&F Fan regulator modular type 02 moduletype250 volts AC complete all as specified and directed. |
| 102 | Supply and fixing MCB SP 6-32 amp rating 240V, 10KA \"C\" curve miniature circuit breaker (MCB) of single pole in the MCB DB complete with connection testing and commissioning complete all specified and directed. |
| 103 | Supply and fixing MCB SPN 40 amp rating 240V, 10KA \"C\" curve miniature circuit breaker (MCB) of single pole in the MCB DB complete with connection testing and commissioning complete all specified and directed. |
| 104 | Supply and fixing sheet metal enclosure distribution board (DB), when MCB to be used, dust and vermin proof, single pole andneutral (SPN) 8 way with 200 Amps rated copper bus bar double door protection, neutral bar, earth bar, single pole and neutral 240 volts, MCBs used as incommer Double door, flush to wall complete all as specified and directed. |
| 105 | Supply and fixing sheet metal enclosure distribution board (DB), when MCB to be used, dust and vermin proof, single pole andneutral (SPN) 4 way with 200 Amps rated copper bus bar double door protection, neutral bar, earth bar, single pole and neutral 240 volts, MCBs used as incommer Double door, flush to wall complete all as specified and directed. |
| 106 | Material and labour for submain wiring using two run of sinlge core PVC insulated cable (FRLS) 6 Sqmm copper conductor multi stranded and 6 Sqmm copper conductor insulated cable (FRLS) using as earth wire drawn through and including PVC rigid conduit of size not less than 25mm dia with accessories (concealed) complete all as specified and directed |
| 107 | M & LEarthing complete with galvanised steel earth plate electrode 60× 60 cm.× 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less\"than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion |
| 108 | Schedule of Credit (Minus) Rs.25844.00NOTE: Bidder shall insert credit amount of Rs. 25844.00 as ratein Green field under Col-13. |
