|
| 1 | Supply installation, testing & commissioning of factory assembled Diesel Engine driven generating set coupled with alternator AC to Give continuous output of 140 KVAat a power factor of 0.8 lagging, 415 volts, AC, 3 phase, 4 wire, 50 HZ, 1500 RPM, diesel engine liquid cooled, mounted on common base frame complete with in built fuel tank of adequate capacity with fuel line & accessories, PCC foundation work as per manufacture\"s instructions, vibration damper pads, micro processed based relay panel for automatic starting on mains failure, control panel showing all parameters of engine & alternator, sound proof canopy & other accessories etc. and confirming to the under mentioned technical specifications complete in all respect as specified & directed Make: Kirloskar/ Ashok Leyland/Greaves Cotton/Cummins .Note: 1. The Alternator shall be suitably de-rating factor for operation at high altitude (above 3,500 meters AMSL), ( delivery laocation- Leh, Ladakh) considering reduced air density and cooling efficiency as per IS: 13364(Part-2) 2. Adquate capacity of Diesel engine as accepted by the Accepting Officer based on manufacturers technical details liquid cooled to drive independently above alternator and after considering derating as per site conditons.(A) DIESEL ENGINE :6 cylinders, water cooled, turbo charged,1500 RPM under NTP conditions conforming to IS -4722, BS-5000, IEC-34/1, ISO 8528, BS-5514, ISO-3046 with an overload capacity of 10% for 12 Hrs of continuous operationwith the following accessorie complete in all respect as specifiedMake: Kirloskar/ Ashok Leyland/Greaves Cotton/Cummins .(a) Radiator with blower fan with guard (b) Pipe coupling for cooling system(c) Coolant inhibitor (d) Filters for fuel/lube oil(e) Fly wheel housing and fly wheel suitable for alternator(f) Engine bearing mechanism in fly wheel housing (g) Shut off coil protection with safeties for LLOP /HWT/ Over speed/high and low DC voltage.(h) Dry type heavy duty replaceable paper element air cleaner with restriction indicator and vacuum indicators .(j)Residential silencers. Cont. to 1.01 |
| 2 | (k)Stainless steel exhaust flexible bellows.(l)Motor driven priming pump.(m) Electric starter motor(n)Battery charging alternator. (o) Exhaust piping made outof \"C\" class MS Pipe inclusive of all accessories and hardware, necessary support as per manufacturer’s recommendations to sustain back pressure with rain cap.(p) Mineral wool insulation covered with aluminium sheets for the entire length of exhaust pipe as per manufacturers recommendations.(q) First fill of oil, coolant and diesel during commissioning.(r)Interconnecting copper cabling of adequate capacity between batteries andcontroller.(s) Fuel pipe. (t) Self starter 12 volts DC. (u) Metering equipments for recording (i) Battery voltage and charging rate (ii) Coolant temperature (iii) Lubricating oil pressure (iv) Engine speed (RPM) (v)Engine hours run (vi) Balance of fuel. Cont. to 1.02 |
| 3 | (v) Safety as protection control (Trip and indication) (i) High water temperature (ii) Low Lube oil pressure (iii) Low and high speed trip (iv) High and low DC voltage (v) over speed (w) Base frame sturdy fabricated welded construction, channel iron base frame (duly painted ) for mounting engine and alternator as per manufacturer’s design alongwith AVM pads (x) Battery: 01 Nos , 12 Volt, 180 AH maintenance free with leads and terminals Make of battery : Exide / Amron(y) Fuel Tank: Built in diesel storage capacity not less than 12 Hrs running of DG set or as per manufacturers recommendations (B) ALTRERNATOR : 140 KVA at 0.8 PF lagging, 415 volts, 3 Phase, 4 wire, 50 Hz at 1500 RPM self excited and self regulated with AVR brushless excitation band of voltage ± 1% of rated voltage from no load to full load insulation class H, self ventilated and conforming to IS4722, BS5000, IEC 34/1, IS0 8528, BS5514, I503046, suitable for above mentioned diesel engine complete all as specified and directed.(C) ACOUSTIC ENCLOSURE : Factory made acoustic enclosure (canopy) having size as per OEMNote: 1. The Alternator shall be suitably de-rating factor for operation at high altitude (above 3,500 meters AMSL), considering reduced air density and cooling efficiency as per IS: 13364 (Part-2) 2. Standard design alternator rated at 140 KVA,net output at site after considering derating as per site.(C) CONTORL PANEL :Controlpanelmadeout of 2mm thick CRCAsheets in suitable compartmentsfront openable duly powder coated, weather proof and long lasting finishing including the followings :-(i) Set of 300Amps electrolytic copper bus bar for phase and neutralmounted over the hygroscopic PVC insulator. (ii) MCCB ,200 A, 4 Pole microprocessor based adjustable magnetic and thermal release setting 70% to 100% rupturing capacity 25 KA, 415 volt, 50 Hz with over load and short circuit protections as approved make – 01 No.(iii) Set of phase indicating lamps showing DG \"ON\" and load \"ON\" Cont to 1.03 |
| 4 | (iv) Voltmeter digital type 0 to500 volts range : 01 No (v) Amp meter digital type 0 to 200 Amps range complete with suitable CT”s- 01 No.(vi) KWH meter digital type(vii) Instrument fuses (HRC type)(viii) Bottom gland plates for incoming and outing cable(ix) Circuit diagram plateCont to 1.04 |
| 5 | Automatic Main Failure (AMF) control panel:- Outdoor type, factory fabricated cubical type, free standing, floor mounted, AMF control panel, provided with removable rear door & hinged front door for easy accessibility, fabricated out of not less than 2.0 mm thick CRCA Sheet powder coated CPRI approved comprising of :-(i) AMF control circuit with 4 pole, MCCB 200 Amps-02Nos, micro process based with thermal and magnetic release setting 70% to 100% rupturing capacity 25 KA make Siemens or Legrand two Nos. each one for commercial and DG set incoming supply with HRC back up fuse complete with all DC control relays/line voltage monitor (LVM) as per OEM specifications incorporating engine start and stop complete as specified and directed.(ii) Digital ammeter (0-500 amps) and voltmeter (0-500 Volts) with selector switch(iii) Digital frequency meter.(iv) Digital power factor meter (-1.0 to +1.0)(v) Indicating lamps for supply \"ON\" and Load \"ON \"(vi) Instrument fuses (HRC type)(vii) Push button 01 No each for start, stop & reset Cont. to 1.05 |
| 6 | NOTES :- (i) TheGenerator set prime mover will produce BHP as per manufacturer\"s recommendation.(ii) Rate quoted shall be deemed to be inclusive of cable and terminations form Generator to the AMF Panel, with necessary holes to wall including making good to distrbed surfaces so as to match with the existing finishes all as specified and directed.(iii) The quoted rate shall be deemed to be inclusive of first filling of lubricant oil. (iv) The quoted rate shall be deemed to be inclusive of 12 hours test run at site including of half an hour on 10% overhead in presence of representative detailed by accepting Officer; including FOL, all arrangements are to be made by the contractor for tests.(v) The contractor shall arrange for artificial load (water load) for testing for final testing of DG Set at site and the cost is deemed to be including in above offer.(vi) Testing of sound level should carried out at the site in presence of Engr-In-Charge. (vii) One year maint spare as per manufacturer\"s maint schedule and as directed by Engr-in-Charge is deemed to be included in the above offer.(viii) One set of latest Spare part catelogue with price, exploded view of parts and user\"s manual are deemed to be included in the offer.(ix) : DG Set should be testing after derating factor(x) : The Gen set must be affixed with label meeting the following requirement ( The label shall be durable and legible) (a) Name and address of the engine manufacturer. (b) Statement that this engine conforms to the environment (PROTECTION) (c) Type and approval certificate number.(d) Date of manufacturing of Gen set. |
| 7 | Supply and Fixing of PVC insulated, heavy duty, LT XLPE galvanised steel strip armoured electric power cableof size 185Sqmm x 3.5 core with stranded aluminium conductor 1100 Volts grade, jointed with cable glands, lugs etc., laid in trenches/drawn through pipe, complete all as specified and directed.( NOTE- Excavation & Earth work will be measured and paid separately) |
| 8 | M&L Earthing complete withgalvanized steel earth plate electrode 60 cmx 60 cm x 6 mm thick buried directlyin ground (earth pit notless than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metres below normal ground level,connecting to thegalvanised iron strip 32×6mm by means of bolts, nuts , check nuts and washers of galvanized iron andgalvanised iron strip protected by provision of GI lightgrade pipe40 mmbore including provision of concrete pitmade from PCC ( 1:2:4) type B-1 (using20 mm graded stone aggregate) with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4 Kg/Sqm) and frame of angleiron40 x 40 x 6 mm and handle of 6 mmdia MS barmade to shape, GI light grade 20 mmbore pipefor watering perforated atbottom, 1.50metre long placed on top edge of earth plate, common salt &charcoalfilling, withfixing arrangement , funnel, wire mesh and earthwork in hard/dense soil, returning filling in and removal of surplus soilto a distance notexceeding50 metres, all as perelectrical plateNo 5 of SSR 2009 Part-I and connecting toMCBDB’searth test point all as specified or indicated including testing on completion, complete all as specified and as directed by the Engr-in-Charge.Note: 1.Rate quoted deemed to include GI protection pipe, funnel, excavation and earth work, in soft/loose soil with PCC type C1 in bed and pit |
| 9 | Excavation in trenches, n.exc 1.5m wide & n.exc 1.5m in depth for foundation etc in Hard and Dence soil & getting out for laying of cable complete all as specified & directed. |
| 10 | Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm in Soft/loose soil complete all as specified and as directed by the Engineer in charge. |
| 11 | Removing excavated material to a distance n.exc 50 mtr and depositing where directed at level n.exc 1.5 mtr above the starting point all as specified and as directed by the Engineer in charge. |
| 12 | M&L Sand cushioning to underground cable complete all as specified in clause 19.75 of SSR Part - I, complete all as specified and directed by Engr-in-Charge.Note: Only punned thickness shall be measured and paid. |
| 13 | Supplying and laying un-reinforced precast concrete cable cover, class LV, type 1 with peak, size 250mm x 150mm x 40mm complete all as specified and directed by Engr-in-Charge. |
| 14 | Supply,Installation ,testing and Commissioning in LT Panel cubical type indoor floor mounted weather proof totally enclosed, (CPRI approved) factory made and made out of 2.0 mm thick CRCA powder coated sheet and angle iron complete with bus bar of copper of suitable size for capacity 400 Amps 3 Phase and Neutral 415 Volts 50 Hz mounted on epoxy type insulators with PCC flooring and angle iron base frame including space to accomodate 10 Nos Dol staretrs compitable for monoblock motor and pump of capacity upto 10 HP each on seperate housing including painting of panel with two coats of synthetic enamel paint over a coat of red oxide primer having IP-54 and conforming to IS-8623 and including following accessories:- Cont. to 9.01 |
| 15 | INCOMING(a) MCCB 250 Amps 4 pole, with short circuit and earth fault protection with earth module breaking capacity 35 KA- 01 Nos OUT GOING(a) MCCB 4P 125 Amps, 415 Volts, 50 Hz \"C\" curve type- 01 Nos(b)MCCB 4P 160 Amps, 415 Volts, 50 Hz \"C\" curve type- 02 Nos(c) MCB SPN63 Amps, 240 Volts, 50 Hz \"C\" curve type - 08 Nos(d) Digital Volt meter with sellector switch(e)Digital Amp meter with sellector switch with necessary CT (f) LED indicating lamp Note :-(i) All MCCBs / instruments / MCBs /Bus Barshall be housed in a separate housing with on- off latches in the housing |
| 16 | Excavation in trenches, n.exc 1.5m wide & exc 1.5mbut n.exc 3m in depth for foundation etc in Hard and Dence soil & getting out for laying of cable complete all as specified & directed. |
| 17 | Labour only for laying of old serviceable cable covers retrieved from excavation complete all as specified and directed by Engineer-in-Charge. |
| 18 | M&L PCC 1:4:8 type D2 using 40 mm graded crushed stone aggregate as in foundation, filling mass concrete including necessary form work. |
| 19 | M&L for PCC 1:3:6 type C 1using 20 mm graded crushed stone aggregate as in copung including necessary form work. |
| 20 | M&L PCC 1:2:4 type B2 using 40 mm graded crushed stone aggregate as in foundation, filling mass concrete including necessary form work. |
| 21 | Pin type, porcelain, vitreous, white, brown or green insulator including one galvanised mild steel spindle, two galvanised iron washers and onegalvanisedironnut, 100mm height, 65mm dia for 1100 volts grade complete all as specified and directed. |
| 22 | Supply and fixingin repair Steel tubular swaged street light polescomplete with pole arms 1.2 m & cast iron base plate ,finial taper plug,bolts,nuts and screws as specified type 410 SP-31 9.0 mtr long and painting with two coat of aluminium paint over one coat of primer on exposed surface of pole all as specified and directed by Engr-in-Charge.( NOTE- Excavation & PCC will be measured and paid separately) |
| 23 | Supply and laying in replacementofXLPE insulated, armoured, haeavy duty electric cables (heavy duty) with stranded aluminium conductor rating 1100 volts grade of size 240 Sqmm 3.5 core laid in trences or passing through pipes.ducts or fixed to walls/poles completer all as specified.( NOTE- Excavation & Earth work will be measured and paid separately) |
| 24 | Supply and laying in replacementofXLPE insulated, armoured, haeavy duty electric cables (heavy duty) with stranded aluminium conductor rating 1100 volts grade of size 95 Sqmm 3.5 core laid in trences or passing through pipes.ducts or fixed to walls/poles completer all as specified.( NOTE- Excavation & Earth work will be measured and paid separately) |
| 25 | Supply and laying in replacementofXLPE insulated, armoured, haeavy duty electric cables (heavy duty) with stranded aluminium conductor rating 1100 volts grade of size 70 Sqmm 3.5 core laid in trences or passing through pipes.ducts or fixed to walls/poles completer all as specified.( NOTE- Excavation & Earth work will be measured and paid separately) |
| 26 | Supply and laying in replacementofXLPE insulated, armoured, haeavy duty electric cables (heavy duty) with stranded aluminium conductor rating 1100 volts grade of size 25 Sqmm 2.0 core laid in trences or passing through pipes.ducts or fixed to walls/poles completer all as specified.( NOTE- Excavation & Earth work will be measured and paid separately) |
| 27 | Taking down old unserviceable feeder pillar box and supply and fix in replacement feeder pillar box of suitable size with incommer MCCB of cpacity 160 Amps, 415Vand4 Nos aluminium bus bar strip along with 14 Nos MCB SPN 63 Amps, 240 Volts, C type with Din rail for moounting and necessary wiring for MCB,s complete size all as specified and directed. |
| 28 | Supply , Installation and Commissioning of Deep freezer Metal top of capacity 300 Litres having double door ,single phase 240 volts 50 Hzcomplete all as per speified and directed by Engr in Charge. Make- Voltas/Blue Star/Hitachi/LG/Samsung |
| 29 | M&L for Point wirnig for Power point 3 pin switch socket 15 Amp with PVC copper conductor cable multistrand unsheathed 2.5 Sqmm on independent board incl one run 1.5 Sqmm multistrand PVC copper conductor cable for earth continuity in and including PVC casing and capping fixed on wall complete all as specified and as directed by Engr in Charge. |
| 30 | Supply and fixing modular switch single pole one way 16 Amps 1 module complete all as specified and directed by Engr in Charge. |
| 31 | Supply and fixmodularsocket 6 A/16 amp -2/3 pin combined 2 module complete all as specified and directed by Engr in Charge. |
| 32 | Supply & fix metal flush box 3 module Complete all as specified and directed by Engr in Charge. |
| 33 | Supply & fix white cover platewith frame (inner plate) 3 module complete all as specified and directed by Engr in Charge. |
| 34 | Demolition of precast concrete block walling built in cement mortar all as specified and as directed. |
| 35 | Taking down cement plaster on brick or concrete surfaces including racking out joints hacking for key, scrubbing down with water etc. complete all as specified and as directed. |
| 36 | M&L for 15mm thick rendering on other than fair faces of brick works finished even and smooth without using extra cement in cement mortar 1:6 complete all as specified and as directed by Engr-in-Charge. |
| 37 | M&L for 15mm thick rendering onfair faces of brick works finished even and smooth without using extra cement in cement mortar 1: 4 complete all as specified and as directed. |
| 38 | M&L for preperation of new plastered wallsurface of any description and applying two coat of cement based paint over a coat of chalk whiting complete all as specified and as directed. |
| 39 | M & L Preparing newly plastered surfaces and applying two coats of distemper oil emulsion including priming plastered and other surfaces with alkali resistant priming paint on surfaces of walls. |
| 40 | Taking down chowkats / frames with shutters (without taking off shutters from the frames) area n\"exc 1.5 Sqm each complete all as directed by Engr-in-charge. |
| 41 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) area exceeding 1.5 Sqm and not exceeding 4 Sqm each complete all as directed by Engr-in-charge. |
| 42 | M & L Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed in cement mortar 1:4 screed bed or bedding layer of mortar and dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises all as specified and directed. |
| 43 | M & L glazed (coloured) ceramic tiles of size (350 x250mm) x7 mm / 450mm x 350mm x 7mm thick, as on vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement as in dado, skirting etc to matchwith the shade of tiles including rendering 10mm thick in cement mortar (1:4) on fair faces of brick work or concrete surfaces as in vertical surfaces for receiving tiles all as specified and Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed. |
| 44 | Demolition of stone slabs and tiles of any description or thickness in floors aprons etc.laid bedded and pointed in any mortar. |
| 45 | M & L for 20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15 mm thick screed bed in CM 1:4 complete all as specified and as directed by Engr-in-Charge. |
| 46 | M&L for pre cast solid block masonry set in CM 1:6& casted in cement concrete type C-1 (1:3:6) using 20mm graded curshed stone aggregate complete all as specified and directed. |
| 47 | S&F mild steel work as in hold fastsand similar work confirming to Fe-290 or Gd -E 165 complete.all as specified and as directed by the Engr-in-Charge. |
| 48 | Material & labour PCC (1:3:6) type C1 (using 20 mm graded stone aggregate) as in hold fast bed block and like including dismantling of any description complete all as specified and as directed by the Engr-in-Charge. |
| 49 | S&F 2nd class soft wood plain, solid, straight chowkets and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete(Glass shall be measured Seperately) all as directed by Engr-in-Charge. |
| 50 | S&F for 30 mm thick2nd class softwood plain framed paneled shutters (any number ofpanels) with panels of timber flat on both sides (feather edged), or ofveneered particle board medium density, wood particle board with commercial face veneers, Supply and fixed to chowkats , complete all as directed by Engr-in-charge. |
| 51 | S&F 2nd class soft wood 35 mm thick Glazed and skelton shutter, open and prepared to receive the glass, gauze etc.(without sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc. (Glass / Wiremesh should be measured seperately) complete all as specified and as directed by the Engr-in-Charge. |
| 52 | M&L sheet glass 4.8 mm thick ordinalry quality and glazing with oil putty or wooden beads in square not exc 0.50 sqm in each pane complete all as specified and as directed. |
| 53 | S&F 150mm long aluminium anodized, barrel tower bolt of extruded sectioncompleteall as specified and as directed. |
| 54 | S&F 100mm long aluminium anodized, barrel tower bolt of extruded section complete. |
| 55 | S&F 150mm size extruded aluminium alloy handles, fabricated type, anodized complete all as specified and as directed. |
| 56 | S&F floor door stopper (Length of cover plate ) 150mm long aluminium alloy body and tongueanodised with hard drawn steel springfixed in floorcompleteall as specified and as directed. |
| 57 | S&Fmild steel butt hinges, medium weight cold rolled 100mm sizecomplete all as specified and as directed. |
| 58 | S&Fmild steel butt hinges, medium weight cold rolled 75mm sizecomplete all as specified and as directed. |
| 59 | S&F in repair aluminium door closer (aluminium extruded section) hydraulically regulated designation No 3, universe type, suitable for door shutte of 851 mm to 1000 in width and of weight 61 to 80 kg. |
| 60 | S&F in repair250mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy fixed complete all as specified and as directed. |
| 61 | S & F in repair fancy type ,chromium plated 20 mm bore angle cock, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed. |
| 62 | S & F in repairs fancy type 15mm bore chromium plated bib taps, cast copper alloy, with crutch or butterfy handle, screwed down, screwed for iron pipe or for brass ferrule. |
| 63 | S & F 25mm dia3 layer PP-R polypropyene random copolymer concealedpipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete all as per manufacture instructions and as directed by Engineer in Charge and including taking up or down 25 mm bore steel tubing / PPR pipe and connections and set aside for re-use or removal to store. |
| 64 | S & F in repairVitreous china wash down water closet (Pedestal), white (EWC) excluding fixing bolts, flushing cistern and flush pipe)including plastic water closet seat, black closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device including connection to drain pipe and to flushing pipe antisyphonage pipe etccomplete all as specified and directed by Engr-in-Charge.Make : CERA/JAQUAR/KOHLER or equivalent. |
| 65 | 10 ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with linlet,ball valve, float and handle including brackets. |
| 66 | S&F in repairs, 15 mm bore, PVC connection pipe 600mm long with PTMT nuts at both ends complete all as specified and directed. |
| 67 | S&F in repair 600x450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial ply wood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed by Engr-in-Charge. |
| 68 | S & F in repair sink with drain board made of Stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe over all size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed by Engr-in charge. |
| 69 | S & F in repairs 750 mm long, 32/ 40 mm dia., PVC flexible Waste pipe including waste coupling. |
| 70 | S & F stainless stell wall mounted kitchen plate rack made of stainless steel 0.80mm thick sheet standard size 750x900x250mm and design as approved by Engr in chagre and fixed to wall with wooden plug & screw (Fixed in repair) complete all as specified and directed by Engr-in-Charge. |
| 71 | S & F two way angle cock, fancy type chromium plated with long shank and cup (two way angle valve type) cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions for bore of pipe 15mm complete all as specified and directed. |
| 72 | S&F in repair 15mm bore CP central hole basin mixer without Popup waste system with 450mm long copper pipeschrome finish complete all as specified and as directed. |
| 73 | S & F in repairs Vitreous china wash basin white flat back size 550 x 400 mm excluding taps, waste,chain and plug and porcelain stopper butincluding cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specified and directed by Engr-in-Charge. |
| 74 | S & Fin repair acrylic PVC bathroom cabinet of size 550 x 400 mm with openable shutter fixed with looking mirror of selected quality and with suitable shelves in side the cabinet of superior quality as approved and directed by Engr in Charge. |
| 75 | S & F in repairs health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25m long flexible tube and ABS wall hook including making connections and fixed in position completed all as specified and directed. |
| 76 | S & F in repair CPtoilet jet spary ABS with double lock 1.2 mtr CP tubestainless steel flexible hose all as specified and as directed. |
| 77 | S & Fin repair CP towel ring of dia 200mmfixed with and includingscrews and wooden/plastic cleats. |
| 78 | M&L for preperation of new or old untreated wood or wood based surface of any description over 10cm width or girth and applying two coat of synthetic enamal paint over a coat of pink primer complete all as specified and as directed. |
| 79 | S & F in repair CP floor gratings 150mm dia all as directed by the Engr-in-Charge. |
| 80 | S & F in repair fancy type glass corner self with CP brackets etc complete all as specified and directed. |
| 81 | S & F Chrominum plated brass soap dish (Oval shape) to walls (size not less than 125mm long) complete fix to wall all as specified and direced by Engr-in-Charge |
| 82 | S & F in repair toilet paper holder with flat recessed type stainless steelfixed with screws complete all as specified and directed by Engr-in charge. |
| 83 | Dismantling plain or corrugated steel sheeting any gauge thickness including nanital or similar pattern. |
| 84 | Dismantling wrought iron or mild steel work of any description not otherwise provided for angle iron or flat iron as in post and guard bars or grating, complete all as specified and as directed by Engr-in-Charge. |
| 85 | S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240. |
| 86 | S &F Pre-painted galvanum aluminum zink coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550MPa as in roof covering /clading to walls fixed with self tapping screws complete all as specified and directed. |
| 87 | M&L for preparation new steel surfaces of any description, not otherwise described, over 10cm width/girth and applying two coats of synthetic enamel paint over a coat of red oxide primercomplete all as specified and as directed. |
| 88 | S&F in repair19mm dia mild steel, chromium plated curtain rods,withbrackets, end bulbs all as specified and as directed by Engr-in-charge. |
| 89 | S&Fin repairsTowel rail 600mm long Cromum plated (Minimum weight 190 gms). |
| 90 | M&L for TMT mild steel bars, 10mm dia and over, as in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with MS wire (annealed not less than 0.9mm dia) , complete all as specified and directed by Engineer-in-charge. |
| 91 | M&L for providing precast cement concrete 1:2:4 type B-1, (using 20mm graded crushed stone aggregate) as in landings, cover slabs (for man holes etc)chullah hoods, chajjas, water troughs, mangers, shelves and similar articles withand similar articles with plain faces and setting in cement mortar 1:6 complete with joints to match including demolition of reinforced cement concrete of any description and in any position not other wise specifically provided for and Removing demolished material to a distance and depositingout site of MoD land Where directed at a level not exceeding 1.5 metre above the starting pointcomplete all as specified and directed by Engineer-in-Charge. Note : S&F reinforcement shall be measured and paid separately. |
| 92 | S&F 75mm bore PVC (SWR) pipe single socketed having compressive strength 655 - 675 Kg/Cm2 , in any length with rubber joints fixed to wallscomplete all as specified and directed by Engr-in-Charge. |
| 93 | S&F 75mm bore PVC (SWR) pipe bends complete all as specified and directed by Engr-in-Charge. |
| 94 | S & F PVC (SWR) 75mm dia, floor trap, plain with grating including jointing to waste pipe with solvent cement. |
| 95 | S&F in repair CP wallmixer 3-in-1 systemwithprovision for bathTelephone showerand over head showerwith bend pipecomplete all as specified and directed by the Engr-in-Charge. |
| 96 | S & F anodised aluminium snap grid of size 605 x 605 frame work of false ceiling including hanger 6mm dia GI (up to 1200 mm length) adjusting level fixed to roof slabs by means of ceiling clearts made out of GI flat 40 x 3 mm size 60mm long and expansion hold fasterners 12.5 mm dia 40mm long complete all as specified and directed by Engr-in-charge. |
| 97 | M & L providing and fixing Gypsum board 12mm thick and 600 x 600 mm in size in ceiling fixed with screw or with staples on snap grid as per manufactured instructions including Dismantlng complete all as specified and directed by Engr-in Charge. |
| 98 | M&L form work for rough finished concrete surfaces to sides and soffits of floor or roof beam ,beam haunchings ,girders, bresum-mers,lintles,cantilevers,shelves including supports ,overhanging, etc. also splays between floors and beams,etc |
| 99 | Form work to edges of concrete flats in floors openings in concrete walls floor and roof and sides of RCC/PCC bands in walls horizontal or sloping and similar work n exc 20 cm wide. |
| 100 | Dismantling of cast iron pipe of internal dia 75mm or reinforced concrete drain pipes, jointed in cement mortor and taking out of trenches , if requiredand complete all as specified and directed by Engr-in-Charge. |
| 101 | Deduct Schedule of Credit of Rs (-) 63051.00 (Minus) as listed in Schedule \"A\" (Contd). Contract Sum shall be arrived after deducting the credit amount.Note :- Tenderers will not quote against this item being a firm amount. |
