|
| 1 | Civil works |
| 2 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 3 | 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) |
| 4 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer |
| 5 | Finishing walls with Acrylic Smooth exterior paint of required shade :Old work (One or more coat applied @ 0.90 ltr/10 sqm). |
| 6 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade:One or more coats on old work |
| 7 | Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot &double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge ( Door handle, lock and stopper etc to be paid separately) |
| 8 | Providing and fixing 3M Fasara frosted etching film of thickness 25 microns self-adhesive of approved colour, shade, and quality with cutting as per approved design and pattern, including cleaning of glass and making surface smooth for fixing of film to the surface, all completed as per the direction of the engineer in charge. |
| 9 | Providing and fixing of glass door SS Patch Lock with out handle in toughened glass door including all necessary screws etc. complete |
| 10 | Providing and fixing SS H handle having min 30cm length in toughed glass door including all necessary screws etc. complete |
| 11 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm,with swan neckfaucet with pipe in let and drain provision, including painting of fittings and brackets, cutting and making good the walls wherever required:Kitchen sink with drain board510x1040 mm bowl depth 250 mm |
| 12 | Providing and fixing uplasticised PVC connectionpipe with brass unions: 45 cm length15 mm nominal bore |
| 13 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 893115 mm nominal bore |
| 14 | Flexible pipe40 mm dia |
| 15 | Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge Concealed work, including cutting chases and making good the wall etc. 15 mm pipe 10kgf/cm2 |
| 16 | Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 32 mm dia 6 Kgf/cm2 - External work - Exposed on wall |
| 17 | Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge.Concealed work,including cutting chased and making good the wall etc. 20 mm pipe 12 Kgf/cm2 |
| 18 | Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge.Concealed work, including cutting chases and making good the wall etc. 32 mm pipe 10Kgf/cm2 |
| 19 | Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge.Concealed work, including cutting chases and making good the wall etc. 50 mm pipe 10 kgf/cm2 |
| 20 | Providing and fixing PVC pipes including fixing the pipe with clamps/clips at 1.00 m spacing. This included jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 75 mm dia 6Kgf/cm2 - External work- Exposed on wall |
| 21 | Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75 mm dia Door Elbow |
| 22 | Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Bend |
| 23 | Providing and fixing to existing door frames.30 mm thick Fiberglass Reinforced Plastic (F.R.P) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF) / Polystyrene foam to be used all filler material throughout the hollow panel, casted monoolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS : 14856, complete as per direction of Engineer-in-charge. |
| 24 | Providing and fixing bright finished brass handles with screws etc. complete:125 mm |
| 25 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions,i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron) |
| 26 | For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Anodised aluminium ( anodised transparent or dyed to required shade according to IS : 1868, Minimum anodic coating of grade AC 15) |
| 27 | Filling the gap in between aluminium/ stone/ wood frame and adjacent RCC/ Brick/ Stone/ wood/ Ceramic/ Gypsum work by providing weather/structural non sag elastomeric PU sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete, complying to ASTM C920, DIN 18540-F & ISO 11600Upto 5 mm depth and 5 mm width |
| 28 | Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS : 12823 Grade I Type II, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer - in- Charge.Pre- laminated particle board with decorative lamination on both sides |
| 29 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) |
| 30 | For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 31 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:125 mm |
| 32 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.Single rubber stopper |
| 33 | Providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles of approved quality for aluminium door, with necessary screws etc complete as per direction of Engineer- in- charge. |
| 34 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. |
| 35 | Providing and fixing aluminium tower bolts, ISI marked, anodised(anodic coating not less than grade AC 10 as per : 1868), transparent or dyed to required colour or shade, with necessary screws complete:300x10 mm |
| 36 | Furniture |
| 37 | Providing and erection of reception counter table of length 1200 mm and first level should be provided at a height of 750 mm and width 600 mm and the second level at a height of 1050mm from base with a width of 300. The table made of 18mm thick pre laminated Medium Density board of exterior grade (Grade I)IS: 14587:1998 with decorative laminated finish on both sides and 2 mm thick PVC beading on all edges, including electrical flip box, cable measurement tray, grommets with 3 nos universal power socket and ethernet port, three drawer pedestal unit with drawer channel, handles, hinges, lock all complete as per approved drawing and installation of Engineer in charge/Architect. |
| 38 | Supply and erection of Airport type 3 seater waiting chair with powder coated chromium finish having minimum dimensions 1675mm length X 710mm width X 775mm total height and 400mm seat height . Seat: High quality cold rolled 1.2mm thick steel perforated sheet pressed and welded to form the shape. Arm & Leg: High quality 1.2mm thick MS Tube / Sheet . Cross bar: High quality cold rolled 2mm thick steel sheet pressed and welded to form the shape. |
| 39 | Supply and erection of Airport type 2 seater waiting chair with powder coated chromium finish having minimum dimensions 1250mm length X 710mm width X 775mm total height and 400mm seat height . Seat: High quality cold rolled 1.2mm thick steel perforated sheet pressed and welded to form the shape. Arm & Leg: High quality 1.2mm thick MS Tube / Sheet . Cross bar: High quality cold rolled 2mm thick steel sheet pressed and welded to form the shape. |
| 40 | L TYPE WORKSTATION WITH MODULAR PEDESTAL STORAGE UNIT 1200*600*750 mm HT PARTITION : TABLE TOP is made of 25mm Thick Medium density fiber board with PVC Edge Banding, UNDERSTRUCTURE: MS Unique Leg Trapezoidal cross section of size 60mm x 50mm x 20mm is made of 1.6mm thick CRCA Powder Coated. Horizontal Beams Below Table Top will be with 50mm x 25mm Rectangular Tube made of 1.6mm thick CRCA Powder coated. Flip Cover Considered, includes three drawer modular pedestal unit ( min width 450mm,depth 500 mm, height 650) with channel handles ,hinges, lock all complete as per approved design of engineer in charge/Architect |
| 41 | Supply and installation of visitors chair Medium Back, Mesh Back cushion seat with fixed supports made of 304 Stainless Steel/ powder coated MS of approved colour or shade as per the instruction of the engineer in charge |
| 42 | Counter Height Stools :Supply and erection of counter height stools ( bar stools ) of following specifications:Revolving adjustable Chrome plated steel body chairs with resistance to the corrosion. Cushion Seat with Lift mechanism for Adjustment of height. Minimum height 750mm before expansion. Medium Back rest and arm rest. Item shall be of reputed make. |
| 43 | Revolving adjustable type Medium height Back Office Chair with arm rest with back tilt and swivel mechanism constructed out of mild steel and high quality plastic. |
| 44 | Supply of phlebotomy chair with optimum design made up of MS Power coated frame and up upholstery type seat,back rest and arm rests.Both side arm rest should be with height and position adjustable system and all as per the instruction of Engineer in charge. |
| 45 | Supplying and fixing of lab work table with 18 mm thick edge moulded granite top supported over 18mm thick marine ply wood of 2500mm,L x 1200mm,W x 850mm, H and powder coated GI frame of section size not less than 50x50x1.5 mm including and providing 4 nos under storage movable cabinents of size 600mm,L x 450mm,D x 750 mm,H and powder coated steel sheet of thickness not less than 1mm with 1 drawer and partition bottom storage space with door including drawer channels, individual locks andhandles all as per the approved drawing and instructions of Engineer in charge |
| 46 | Cabinet/Wardrobe: Providing and errectionofCabinet/Wardrobe unit madewith 18 mm thick prelaminated MDF boardof one side decorative lamination and other side balancing lamination having total unit dimension of 900mm,L x 450mm,Dx 2400mm,H andall edges to be sealed with PVC edge beeding of 2.00 mm thick including all fittings such as autoclose hinges,chromium plated brass individual locks & handles ,tower boltsetc all required.All shelves to be fix with proper support and bracket holders at a spacing of 400 mm centre to centre and all as per the drawings and instruction of Engineer in charge. boardmake : Greenlam/ Merino / Century/ equivalent . Only front elevation will be measured. |
| 47 | Supply of Fowler Bed with Mattress & Cushion (for Hospital Purpose) having Top flat platform made of perforated CRC sheet of thickness of 16G or better. Bed frame must be sturdy and stable to support weight of at least 170 kg. The frame structure should be made up of at least 16 G CRC, rectangular / circular pipe of 100 mm x 30 mm and mounted on trolley base made up of 100mmx30mm CR C rectangular pipe of 16 gauge. All adjustments for fowler position must be obtained from crank shaft, manually operated with stainless steel/ABS foldable handle on both the shaft. Fowler bed should be of following dimension: Mattress area of Length 2000 to 2010 mm x Width 900 to 1000mm x Height: - 500 to 550mm (without mattress). The finished bed must be rust proof, pre-treated and polished Stainless Steel. The bed should have telescopic side rails of stainless steel of 22 Gauze with spring loaded locking arrangement on both sides. Should have easily removable head and foot panels made up of ABS plastic. Should have strong & good quality single wheeled total locking type Swivel Castors of 125 to 150 mm diameter with breaks on all four castors for stabilized position. There should be suitable buffer mechanism to avoid hitting of the bed to the wall from all sides.Should have provision of fixing suitable rod for hanging intravenous / irrigation fluid bottle on both sides at head end and foot end. Each bed should be supplied with 1 no. good quality & I. V. rod. Should have hooks on bed frame on both side for holding urine / drainage bag (at least 2 Nos. on each side). Hooks should be in- turned to prevent injury to bystander. Bed production facility to be US FDA registered. Bed to be European CE and facility to be ISO 9001, 14001 and 13485 approved. Mattress to be four sectional and to be combination of good quality foam and coir layer and exactly fitting to the bed. |
| 48 | Slotted Angle Racks : Supply and errection of Powder coated slotted angle metalic rack having min 8 shelfs made up of min 40 X 40 X 2 mm size rolled steel angle posts shall have 8-mm diameter holes provided at 50-mm centre to centre. Metal shelves shall be made from mild steel sheets not less than 1.0 mm in thickness and with sufficient stiffners. Shelves shall have lipped flanges width of flange being 30 mm and depth of lip 15 mm .Min size of rack 900mm Length X 300mm Depth X 2000mm Height. |
| 49 | Lab work bench -The work bench top made up of 18mm thick granite top edge moulded over 18 mm thick marine plywood and GI Powder coated frame work of section size not less than 50x50x1.5mm. The width of the table shall be 750mm and height shall be 850mm. The frame provided with level adjusting screws fixing accessories ,carriage of material all complete as per the approved drawings and direction of Engineer in charge.Note Only length of the table shall be measured for making payment. |
| 50 | Supply of mounded Pantry Table with Heavy Duty stainless steel Legswith minimum dimension of 1200mmx 800mm |
| 51 | Supply of pantry chair made of high-quality moulded polypropylene (PP) material, ergonomically designed with contoured seat and backrest, strong legs with anti-skid rubber pads, lightweight yet durable, water-resistant, termite-proof, corrosion-free and easy to clean, suitable for pantry/office use, complete in all respects including all taxes, packing and transportation to site, as approved by the Engineer-in-Charge. |
| 52 | Vinyl Transparent Vision Glass Stickers: Supply and pasting of Vinyl Transparent Vision Glass Stickers in approved size and design in glass partition and door as per the instruction of Engineer in Charge. |
| 53 | Backlit Acrilic Board with projected letters: Supply, installation, testing and commissioningof weatherproof backlit acrilic board with projected letters made upof 20mm thick acrilic board and having box depth of min 100mm in approved size and design with reqired LED strips for high glow light. The board shall be fabricated and fixed over suitable welded and painted 25X25X3mm MS angle frame in suitable location and in proper line and level with all necessary fastners, supports etc.Electrical works likes electrical wirings, connections, fittings, externaly fixed weather proof 2/3 pin plug points and sockets including boxes etc. to be complete properly.All fabrication and fixing should be done as per approved design and instructions of Engineerin Charge. (Note: Only front elevation will be measured.) |
| 54 | Demolishing |
| 55 | Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.In cement mortar |
| 56 | Wiring |
| 57 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C |
| 58 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes ofFRLS PVC insulated copper conductor, single core cable in surface / recessedmedium class PVC conduit as required2x1.5 sq.mm + 1x1.5 sq.mm earth wire |
| 59 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes ofFRLS PVC insulated copper conductor, single core cable in surface / recessedmedium class PVC conduit as required2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 60 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes ofFRLS PVC insulated copper conductor, single core cable in surface / recessedmedium class PVC conduit as required2 X 4 sq. mm + 1 X 4 sq. mm earth wire |
| 61 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 6 Sq.mm + 1 x 6 sq.mm earth wire |
| 62 | Fixtures |
| 63 | Supplying and fixing suitable size GI box with modular plate and cover in front onsurface or in recess, including providing and fixing 3 pin 5/6 amps modular socketoutlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to beused in non residential buildings) |
| 64 | Supplying and fixing suitable size GI box with modular plate and cover in front onsurface or in recess, including providing and fixing 6 pin 5/6 & 15/16 ampsmodular socket outlet and 15/16 amps modular switch, connection etc. as required |
| 65 | Supply, Installation of surface mounted LED Tubelight. The luminaire should haveCRI > 80 and CCT of both 6500K/5700K. The luminaire shall be compliant withIP20 and IK02 classification. Luminaire shall be designed to emit at least 3600nominal lumens and efficacy of atleast 105 lumen/watt and Minimum system wattageof 30 Watts. The luminaire shall be designed so as to ensure lumen depreciation of upto 30% over 25k burning hours. The electronic driver used shall have a power factor>0.95 and THD. Make - Philips, Crompton, Wipro, Havells |
| 66 | Supply and Installation of surface/recess mounted LED Round/Square luminaire with CRCA housing suitable with fully diffused diffuser for general lighting in offic eareas. The luminaire should have CRI > 80 and CCT of both 6500K/5700K, Cool White Light. The luminaire shall be compliant with IP20 and IK02 classification.Luminaire shall be designed to emit at least 1000 nominal lumens and efficacy ofatleast 105 lumen/watt and Minimum system wattage of 10 -15 Watts. The luminaire shall be designed so as to ensure lumen depreciation of up to 30% over 50k burning hours. The electronic driver used shall have a power factor >0.95 and THD. For light fittings to be installed in false ceiling, all required cuttings shall be made and damages shall be made good as per the direction of Engineer in charge. Make-Philips, Crompton, Wipro |
| 67 | Supply, conveyance, installation, testing and commissioning of ceiling fans of the following sizes using standard accessories excluding resistance type regulator, wiring the down rod with PVC insulated and PVC sheathed 650/1100V grade 3 core round copper conductor flex wire or with extended original wiring etc. as required. 1200mm sweep - 5 star rated, 3 blade ceiling fan complete with 300mm down rod, canopies, shackles. |
| 68 | Supplying and fixing two module stepped type electronic fan regulator on the existingmodular plate switch box including connections but excluding modular plate etc. as required. |
| 69 | Supplying, conveyance and Installation of 3 blade, 400 mm sweep, 1400 rpm Wall Mount Fan including frames and all mounting accessories complete. Recommended Make: USHA/ Havells/ Bajaj / Almonard or equivalent |
| 70 | Supplying, conveyance and Installation of 150 mm sweep,1800 rpm Exhaust Fanincluding frames and allmounting accessories complete. Recommended Make: USHA/Havells/Bajaj or equivalent |
| 71 | Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required. |
| 72 | Supplying and fixing brass batten/ angle holder including connection etc. as required. |
| 73 | Supply, Installation of 12 Watt LED Bulb. |
| 74 | DB and Switchgear |
| 75 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 16 way, Double door |
| 76 | Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, \"\"C\"\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole |
| 77 | Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. |
| 78 | Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps |
| 79 | Supplying and fixing Cable End Boxes (IP 43) suitable for following single poleand neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess,complete with testing and commissioning etc. as required.For 6 way, Double door SPN MCBDB |
| 80 | CCTV and Networking |
| 81 | Supply, Conveyance and Installing of 2MP IP Dome/Bullet Camera having 1/3"Progressive Scan True Day and Night Colour IR Camera having effective pixel of 2MP, Video frame rate of 2MP @30FPS, Minimum illumination of 0.01 [email protected], 0lux@IR On, 20 M IR Range, 24 IR LED, AWB, AGC, BLC, 2D Noise reduction,with 3.6mm board lense, 12 VDC, PoE IP67 rated weatherproof performance. 1 year warranty. Make: Bosch/CP Plus/Honeywell or equivalent |
| 82 | Supply, Installation and Integration of 8 channel embedded Linux PoE, NVR (Network Video Recorder), having dual core embedded processor, must connect 8 channel IP cameras , should support min 2 SATA HDD each of 6TB and must recordvideo simultaneously, (Recording Type: Continuous, Motion Detection, Alarm, SmartEvent, Event Motion Detection, Alarm, Smart Event), Video Compression H.265(HEVC)/H.264+/H.264, 2 Year Warranty, Image quality should be maintainedthroughout the warranty period. Make: Bosch/CP Plus/Honeywell or equivalent |
| 83 | Supply and Installation of Network Switch. 8 Port PoE Switch 1000BASE-T Copper Ethernet PoE+ connections, 10M/100M/1G RJ-45 copper ports, 1000BASE-X Fiber SFP ports, 8 port Auto sensing 10/100/1000 Mbps PoE, minimum CPU memory 512 MB with 2 SFP/combo ports, Energy Efficient Ethernet (IEEE 802.3az). Make: Cisco/CP Plus/ Netgear or equivalent |
| 84 | Supply and fixing of 6U wall mounting rack with supply and fixing of mounting brackets for support Lockable Front Door and Detachable Side Doors, Cable Manager and PDU of 4 or 6 sockets including cooling fan with accessories complete |
| 85 | Supply and Installation of 8TB hard disk |
| 86 | Supply and Installation of LED Color Monitor of minimum 32 inch screen, complete, UHD display Make: LG/Samsung/Panasonic or equivalent. |
| 87 | Supplying and drawn of UTP 4 pair CAT 6 LAN cable in the existing surface/recessed steel/PVC conduit as required1 run of Cable |
| 88 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm |
| 89 | Supplying and fixing RJ45 Outlet including cover plate, Keystone Jack and Gang box supporting, connection etc. as required |
| 90 | Air conditioning system |
| 91 | Supply, installation, testing and commissioning of Split Air Conditioner of followingcapacity and specifications: Consisting of high wall-mounted type room unit (fan coil) with cordless remote control and one number outdoor condensing unit comprising of energy-efficient suitable rotary compressor for operation on single phase, 230 V, 50Hz supply, fixing the outdoor unit on a raised platform as per manufacturers recommendation and fixing of room (fan coil) unit on wall, standard 4m distance refrigerant copper piping with 13mm nitrile rubber insulation, providing and making interconnection between room & condenser as per site conditions, comprising of 1inch dia drain PVC pipe with insulation up to 4 m, canvas connections, full electrical cabling from power plug near indoor unit and to outdoor unit, ODU MS stand, first charge refrigerant gas, suitable stabilizer etc complete as required. (Make: Voltas, Blue Star, Hitachi, Carrier or equivalent). 2 TR 3 Star rated (inverter type AC) as per BEE |
| 92 | Supply, installation, testing and commissioning of Split Air Conditioner of following capacity and specifications: Consisting of high wall-mounted type room unit (fan coil) with cordless remote control and one number outdoor condensing unit comprising of energy-efficient suitable rotary compressor for operation on singlephase, 230 V, 50Hz supply, fixing the outdoor unit on a raised platform as per manufacturers recommendation and fixing of room (fan coil) unit on wall, standard 4 m distance refrigerant copper piping with 13mm nitrile rubber insulation, providing and making interconnection between room & condenser as per site conditions, comprising of 1" dia drain PVC pipe with insulation up to 4 m, canvas connections, full electrical cabling from power plug near indoor unit and to outdoor unit, ODU MS stand, first charge refrigerant gas, suitable stabilizer etc complete as required. (Make: Voltas, Blue Star, Hitachi, Carrier or equivalent). 1.5 TR 3 Star rated (inverter type AC) as per BEE |
| 93 | Supply and Installation of additional copper piping, cabling from indoor to outdoor and drain piping for air conditioning unit with proper insulation including all required on wall/above false ceiling complete |
| 94 | UPS |
| 95 | Supply, Installation, Testing and Commissioning of True on-line Double Conversion 6 KVA UPS system with 1:1 Crest Factor Single Phase Phase Input & SinglePhase Output. Inversion shall be Microprocessor controlled with instantaneous sine wave Control using IGBT. UPS shall have standard display features, alarms, safeties, etc Input Voltage range : a) Phase & Single Phase with ground b)Votage range 190 VAC & 250 VAC c)Input Frequency : 50/60 Hz d)Power Factor : 0.95 or above e)THD : less than 5% with full load Bypass f) Voltage Range – 200VAC – 240 VAC g) Frequency range & 45-55 Hz/55-65 Hz Output Voltage Range h)Voltage Range & 200VAC – 240 VACi)Frequency range & 50/60 Hz j)Voltage distortion & linear load = 2% k)Voltage distortion &nonlinear load = 5% l)Output waveform – pure sinewave m) Minimum Back up time : Continuous 60 Minutes at full load Rectifier shall be Full wave Type (Shall fully meet the specified input power requirements) Battery Type: Sealed Lead Acid Maintenance Free DC Voltage : 24/48/96V DC System, Battery Nos and capacity shall be designed for optimum storage space. Make: Liebert Vertiv/APC by Schneider/Numeric by Legrand |
| 96 | Visi Cooler and Refrigerator |
| 97 | Supply and Installation of 260 litre refrigerator, direct-cool model with a minimum 3-star BEE rating and stabilizer-free operation. It shall use eco-friendly refrigerant (R600a) and have a high-efficiency, low-noise compressor. The unit shall include toughened glass shelves, a vegetable crisper, bottle storage for 2L bottles, an internal freezer compartment, and a removable anti-bacterial gasket. It shall operate on 230V, 50Hz AC and include standard accessories such as an ice tray and egg tray. The refrigerator shall have 1-year comprehensive warranty and 10-year compressor warranty, with BIS certification. |
| 98 | Visi Cooler/Pharmacy refrigerator: Supply, installation and commissioning of lab/pharmacy refrigerator as per following specification: Upright Show case Coolers/refrigerators with Single Glass Door and Lock having 350-450 Liter capacity, Temperature range capability 1-10 degree Celsius with Digital Temperature Controller and Display, Minimum of 4 adjustable Shelve/Rack Recommended Make: BLUE STAR |
