Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Earth work/Fly ash in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil. |
| 2 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. |
| 3 | Filling with available fly ash and earth (excluding rock) in trenches or embankment in layers (each layer should not exceed 15 cm), with intermediate layer of compacted earth (Soil density of 98%) after every four layers of compacted depth of fly ash, sides & top layer of filling shall be done with earth having total minimum compacted thickness 30 cm or as decided by Engineer -in-charge, including compacting each layer by rolling/ ramming and watering, all complete as per drawing and direction of Engineer -in - charge. |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work above plinth level :1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 5 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work above plinth level : 1:1.5:3 (1 cement: 1.5 coarse sand (zone-Ill) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 6 | Centering and shuttering including strutting, propping etc. and removal of form forShelves (Cast in situ) Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 7 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 8 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 9 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand) |
| 10 | Extra for providing and placing in position 2 Nos 6 mm dia. M.S. bars at every third course of half brick masonry. |
| 11 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished,machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour, shade and size etc. (Basic prize Rs 250/- per Sqft) |
| 12 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work |
| 13 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Sal wood |
| 14 | Providing and fixing Pre-laminated flat pressed 3 layer (medium density) particle board or graded wood particle board IS : 3087 marked, with one side decorative and other side balancing lamination Grade I, Type IIexterior grade IS : 12823 marked, in shelves with screws and fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid separately). 25 mm thickMake Greenply or equivalent |
| 15 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on bothfaces of shutters: 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws Make Greenply or equivalent |
| 16 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. piano hinges with necessary screws Make Greenply or equivalent |
| 17 | Providing and fixing aluminium(Heavy Duty )die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. Make dorma/Doorset |
| 18 | Providing and fixing aluminium sliding door bolts, ISI marked Powder coated transparent or dyed to required colour or shade, with nuts and screws etc. complete : 250x16 mm Make Classic or equivalent |
| 19 | TProviding and fixing aluminium tower bolts, ISI marked, Powder coated transparent or dyedto required colour or shade, with necessary screws etc. complete :250x10 mm Make Classic or equivalent |
| 20 | TProviding and fixing aluminium tower bolts, ISI marked,Powder coated transparent or dyedto required colour or shade, with necessary screws etc. complete :150x10 mm Make Classic or equivalent |
| 21 | Providing and fixing aluminium handles, ISI marked,Powder coated transparent or dyed to required colour or shade, with necessary screws etc. complete :125 mm Make Classic or equivalent |
| 22 | Providing and fixing aluminium hanging floor door stopper, Powder coated transparent or dyed to required colour and shade, with necessary screws etc. complete. Make Classic or equivalent |
| 23 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. Make Jindal/TATA |
| 24 | Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete. S.S Wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides |
| 25 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick |
| 26 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. |
| 27 | Providing and fixing 1st quality ceramic glazed wall tiles30 X45 cm size digital series with highlighter conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. makeKajaria digital hi-definition ceramic wall tilesseriesor equivalent make |
| 28 | Providing and laying double charge Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polimer modified quick set tile adhsive water based. conforming to IS 15477 average 10mm / chemical andjointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments, etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily .Double charge vitrified tile polished finish of size. Size of Tile 600 x 600 mm or more. Make kajaria Double charge/classic sonics polished vitrified tiles |
| 29 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter Make :- Supreme or Equivalent |
| 30 | 12 mm cement plaster of mix :1:4 (1 cement : 4 Fine Sand) |
| 31 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :New work (two or more coats) over and including water thinnable priming coat with cement primer Make Asian/Nerolac/Dulux paint |
| 32 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :two coats on New/old work Asian/Nerolac/Dulux paint |
| 33 | Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer of Jk wall putty/Asian/Birlawallcare putty, over the plastered wall surface to prepare the surface even and smooth complete. |
| 34 | Removing dry or oil bound distemper/white wash, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 35 | Repairs to plaster ofthickness12mm to20mminpatches ofarea 2.5 sq. meters and under including cutting the patch in proper shape, raking outjointsandpreparingandplasteringthesurfaceofthewalls completeincludingdisposalofrubbishtothedumpinggroundwithin 50metres lead : With cement mortar 1:4 (1 cement : 4 fine sand) |
| 36 | Demolishing cement concrete manually/ by mechanical means including disposal of material within CSIO as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 37 | Demolishing cement concrete manually/ by mechanical means including disposal of material within CSIO as per direction of Engineer - in - charge. Nominal concrete 1:4:8 or leaner mix (including equivalent design mix) |
| 38 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within CSIO as per direction of Engineer-in-charge.In cement mortar |
| 39 | Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within CSIO as per direction of Engineer-in-charge : 15 mm to 40 mm nominal bore |
| 40 | Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within CSIO as per direction of Engineer-in-charge :Above 40 mm nominal bore |
| 41 | Dismantling C.I. pipes including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means breaking lead caulked joints, melting of lead and making into blocks including stacking of pipes & lead at site within CSIO as per direction of Engineer-in-charge:Up to 150 mm diameter |
| 42 | Dismantling of low/high level cistern,EWC,Wash basin of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal ofunserviceable materials within CSIO. |
| 43 | Dismantling frames, doors, windowsplaster/tiles/chips and cleaning the surface for plaster including disposal of rubbish to the dumping ground within CSIO. |
| 44 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond CSIO for all leads including all lifts involved. |
| 45 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. Make :- Cera/Hindware |
| 46 | Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover,Hand Jet CP cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge. Make :- Cera/Hindware |
| 47 | Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm or similar size with CP push type flushing system with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including arrangement of push typepainting of fittings and cutting and making good the walls and floors wherever required :Range of two half stall urinals with Push type flushing sytem |
| 48 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass push type pillar tap. Make :- Cera/Hindware |
| 49 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. |
| 50 | Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & including GI pipe reach to waste outlet as per the direction of Engineerin- Charge. Make Cera or equivalent |
| 51 | Providing and fixing P.V.C. waste pipe for sink or wash basin including Flexible pipe32 mm dia P.V.C. waste fittings complete. points of approved quality conforming to IS:893115mm nominal bore Make :- Viking or equivalent |
| 52 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 53 | Providing and fixing Lookingmirror of superior glass (of approved quality) an dof required shape and size with wood teak beading frame of approved 6 mm thick hard board backing :Rectangular shape 1500x450 mm. as per direction of Engineer in Charge. Make saint gobind or equivalent |
| 54 | Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. |
| 55 | Providing and fixing toilet paper holder : C.P. brassMake Cera or euqivalent |
| 56 | Providing and fixing soil, waste and vent pipes :100 mm diaSand cast iron S&S pipe as per IS: 1729Make :- NIF/RIF/BIC or equivalent |
| 57 | Providing and fixing soil, waste and vent pipes : 75 mm diaSand cast iron S&S pipe as per IS: 1729Make :- NIF/RIF/BIC or equivalent |
| 58 | Providing and fixing plain bend of required degree.100 mm diaMake :- NIF/RIF/BIC or equivalent |
| 59 | Providing and fixing plain bend of required degree.Make :- NIF/RIF/BIC or equivalent 75 mm dia |
| 60 | Providing and fixing single equal plain junction of required degree : 100x100x100 mmSand cast iron S&S as per IS - 1729Make :- NIF/RIF/BIC or equivalent |
| 61 | Providing and fixing single equal plain junction of required degree : 75x75x75 mmSand cast iron S&S as per IS - 1729Make :- NIF/RIF/BIC or equivalent |
| 62 | Providing and fixing collar :100 mmSand cast iron S&S as per IS - 1729 Make :- NIF/RIF/BIC or equivalent |
| 63 | Providing and fixing collar : 75 mmSand cast iron S&S as per IS - 1729 Make :- NIF/RIF/BIC or equivalent |
| 64 | Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter : 100 mm |
| 65 | Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter : 75 mm |
| 66 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :100 mm inlet and 75 mm outlet:Sand Cast Iron S&S as per IS: 1729Make RIF/Adhunik/NECO/BC |
| 67 | Providing and fixing CP towel ring with concealed fittings arrangement of approved quality. Make Cera or equivalent |
| 68 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. Internal work/external work 40 mm dia nominal bore Make TATA/ Jindal (Hissar) or Equivalent |
| 69 | Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall :15 mm dia nominal bore. Make TATA/ Jindal (Hissar) or Equivalent |
| 70 | Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall :20 mm dia nominal boreTATA/ Jindal (Hissar) or Equivalent |
| 71 | Providing and fixing brass stop cock of approved quality 20 mm nominal bore. Make Zoloto or equivalent |
| 72 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :150 mm diameter |
| 73 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 15 mm nominal bore . Make SVW/UNIK/UF |
| 74 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 20 mm nominal bore Make SVW/UNIK/UF |
| 75 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 40 mm nominal bore Make SVW/UNIK/UF |
| 76 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes including ball valve (brass), Nipple outlet and inlet and all other necessary fittings. Make :- Diplast/Plasto or equivalent |
| 77 | Providing and fixing C.P brass bib cock of approved quality : 15 mm nominal bore15 mm nominal bore. Make Cera or equivalent |
| 78 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards 15 mm nominal bore Make Cera or equivalent |
| 79 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore Make Cera or equivalent |
| 80 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:893115mm nominal bore. Make Cera or equivalent |
| 81 | Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge. |
| 82 | Providing and fixing CP grating of approved quality and colour. Circular type 100 mm nominal dia Make Chilly or equivalent |
| 83 | Providing and fixing CP soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements,weighing not less than 106 gms.Make Cera or equivalen |
| 84 | Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour |
| 85 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portionpowder coated aluminium (minimum thickness ofpowder coating 50 micron). Make Jindal /nalco |
| 86 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :For shutters of doors, windows & ventilators including providing and fixing hinges/hasp and staple, pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings Polyester powder coated aluminium (minimum thickness of powder coating 50 micron shall be paid for separately) Polyester powder coated aluminium (minimum thickness of powder coating 50 micron). Make Jindal /Nalco |
| 87 | Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides. Make Novopan, action tesa |
| 88 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)Make :- SaintGobin/ModiGuard |
| 89 | Providing and fixing machine moulded aluminium coveringfor construction joint of approved pattern & design, made out of machine cut aluminium sheet and machine holed for receiving dash fastener, over expansion joints on vertical surfaces/ceiling floors, the fixing on plate in one row on one side of joint only shall be done with stainless steel dash fasteners of 8 mm dia and 75 mm long bolt including providing aluminium washers 2 mm thick & 15 mm dia , at a staggered pitch of 200mm centre to centre including drilling holes in the receiving surface and providing expandable plastic sleeves in holes etc. complete as per direction ofEngineer-in-charge. Anodised aluminium sheet 2.5mm thick (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) |
| 90 | Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS : 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints ofPVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm). |
| 91 | Dismantling roof\" old plaster or skirting or gola raking out jointsand cleaning the surface for plaster including disposal of rubbish to the dumping ground within CSIO. |
| 92 | Finishing the roof surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster andfinally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep and including the corner gola. |
| 93 | Waterproofing :- Premix Compound Components A and B using an electric double-paddle mixer for 2–3 minutes at low speed. Apply the first coat of Compound at a rate of 0.80–0.90 kg/m² without dilution, using a lamb’s wool or cloth roller. While the coating is still wet, roll and embed a 225 gsm Fiberglass Chopped Strand Mat, ensuring full bonding without air bubbles or wrinkles. Allow the first coat to dry for 3–4 hours. Apply the second coat at a 90° angle to the first. Overlap the chopped strand mat by at least 5 cm at the joints, ensuring the overlaps are sufficiently wet to achieve proper bonding. Once the surface is dry enough to walk on, apply the second coat at 0.80 kg/m². Apply additional coats as needed to achieve a total dry film thickness of 900–1000 microns, with a total system material consumption of 1.60 kg/m² over 2–3 undiluted coats. Note – Coating should be terminated below the drip mould on the vertical surface. The material has followed technical properties: Attains a Tensile Strength ≥ 18 N/mm2 as per ASTM D 2370; Crack bridging ability, Tear Strength ≥ 160 N/mm as per ASTM D 624, Dynamic Crack bridging as per EN 13251:2016 - No Cracks after 20000 sinusoidal cycles, Dynamic Crack bridging as per ASTM C 1305-2016 - Pass, No Crack, Pass Low Temperature Flexibility (-20 after 1000 Hrs. UV as per ASTM D 1970-2021, Shore A as per ASTM D2240 – 85 , Peel Adhesion to Concrete under wet Condition -24 Hrs. – N As per ASTM C 794 – 11.4 , Abrasion resistance (CS 17 Wheel -1000 Cycle, 1.0 Kg) as per ASTM D 4060 - 7 mg , Depth of Water Permeability @ 10 Bar as per EN 12390-8-2019 – Nil Water Migratlon Resistance as per ASTM D 7281,-2007 - No Leakage, Pass Spread of flame Class makes BASF, Pidilite, Fosroc, MAPEI, CIPY . The Operation shall becarried out after scrapping and properly cleaning the surface to remove loose particle with wire brushes complete in all respect as per direction of engineer in charge.All the agencies should be having valid trained/authorized applicator certificate certified by the agency i.e. BASF, Pidilite wonderproof , Fosroc, MAPEI, CIPY. |
| 94 | Providing gola 75x75 mm, Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase |
| 95 | Providing and fixing3 mm thick translucent white acrylic plastic sheet on aluminium door etccomplete as per architectural drawings and directions of engineerin- charge. |
| 96 | Carrying out petty jobs of carpentary including of doors, Almirah, pelmets, storage spaces etc. complete with necessary tools, drill machine nails, screws ,fevicol, SR etc. at diffrent locations which can not be measured as directed by engineer in charge. |
| 97 | Carrying out petty jobs of massonary work including of alltypes of repairs with coc. And mortar etc. complete with necessary tools, cement, sand, aggregate etc.at diffrent locations which can not be measured as directed by engineer in charge. |
| 98 | Carrying out petty jobs of welding workswith necessaqry tools, welding set &rods etc. for petty works at diffrent locations which can not be measured as directed by engineer in charge.which otherwise can not be mearsured. |
| 99 | Carrying out petty jobs of misc.petty workswith all necessary tools,Rehri,etc.at diffrent locations which can not be measured as directed by engineer in charge. |
| 100 | P/F Polysulhide for Sealing of old RCC or Brick construction joints upto 75 mm width including removing the spalling concrete and filling the depth of joints withthermocol etc.then sealing with polysulphide sealent of minimum one cm thickness on both faces at all heights including Fixing on top felxible polyolefin sealing tape for building joint i.e seal Tape. make Dr Fixit & including scaffolding wherever requiredall complete as directed by Engineer in charge |
| 101 | Finishing walls/Roofwith Damp Proof Paint with additives of required shade (Two coats ). including priming coat of one coat ofprimer appliedMake :- Asian Damp Proof paint or Equivalent The Operation shall becarried out after scrapping and properly cleaning the surface to remove loose particle with wire brushes complete in all respect as per direction of engineer in charge |
| 102 | Labour Charges for the following Jobs including minor assorted material likes aluminium/copper thimbles, pvc tapes, fastners, screws, washers etc. as required to complete the job:-Labour charges for dismantling of existing TPIC Switches (including disconnection of cables), Dismantling & Refixing of existing Distribution Panels-02 Nos.,Bus Bar Chamber, dismantling ofcomplete electrical points wiring of 1st Floor of Hostel-B (From Rooms,Toilets & Bathroms- 4 Nos. (1st & 2nd Floor etc.) Light Plug & Power Plug switch boards, exhaust fan, steel/PVC wiring/cabling conduits, etc., fitting and fixture etc.including dismantling & reinstallation of 4 Nos. electrical geysers and dismantled matetrial is to be shisfted from site to store as required& as per direction of Engineer-in-charge.Note:- Before quoting the rates visit the site for assessment of the work. |
| 103 | Wiringforlightpoint/fanpoint/exhaustfanpoint/callbell pointwith1.5sq.mmFRLSPVCinsulatedcopperconductor single core cable in surface / recessed medium class PVC conduit,withmodularswitch,modularplate,suitableGIbox andearthingthepointwith1.5sq.mmFRLSPVCinsulated copper conductor single core cable etc. as required.( Group-A) |
| 104 | Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. |
| 105 | Wiring for circuit/ submain wiring alongwith earth wire with 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required. |
| 106 | Wiring for circuit/ submain wiring alongwith earth wire with 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required. |
| 107 | Wiring for circuit/ submain wiring alongwith earth wire with 2X4 sq mm + 1X4 sq mm earth wire PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required. |
| 108 | Wiring for circuit/ submain wiring alongwith earth wire with 2 X 6 sq. mm + 1 X 6 sq. mmearth wire with PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required. |
| 109 | Supplying and fixing metal box of size 100 mm X 100 mm X 60 mm deep(nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required. |
| 110 | Supplying and fixing metal box of size 180 mm X 100 mm X 60 mm deep(nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required. |
| 111 | Supplying and fixing 1 or 2 Module (75mmX75mm) , GI box alongwith modular base & cover plate for modular switches in recess etc. as required. |
| 112 | Supplying and fixing 3 Modules (100mmX75mm), GI box alongwith modular base & cover plate for modular switches in recess etc. as required. |
| 113 | Supplying and fixing 6 Module (200mmX75mm), GI box alongwith modular base & cover plate for modular switches in recess etc. as required. |
| 114 | Supplying and fixing 8 Module (125mmX125mm), GI box alongwith modular base & cover plate for modular switches in recess etc. as required. |
| 115 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. |
| 116 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. |
| 117 | Supplying and fixing 5/6 A modular switch on the existing modular plate & switch box including connections but excluding modular plate etc. as required. |
| 118 | Supplying and fixing 2 way 5/6 A switch on the existing modular plate & switch box including connections but excluding modular plate etc. as required. |
| 119 | Supplying and fixing modular 3 pin 5/6 A socket outlet on the existing modular plate & switch box including connections but excluding modular plate etc. as required. |
| 120 | Supplying and fixing 15/16 A modular switch on the existing modular plate & switch box including connections but excluding modular plate etc. as required. |
| 121 | Supplying and fixing modular 6 pin 15/16 A socket outlet on the existing modular plate & switch box including connections but excluding modular plate etc. as required. |
| 122 | Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. |
| 123 | Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required |
| 124 | Supplying and fixing brass batten/ angle holder including connection etc. as required. |
| 125 | Supply & fixing of cubical type, indoor type, single door, wall mounted, fixed type, dust proof 200A 4 strips aluminium bus bar made out of in suitable Sheet Steel Enclosure duly painted with siemen gray powder with all accessories & Rubber Gasket etc. as required. Overal Box Size (Approx): (H)455mm x (W)330mm x (D)150mm. |
| 126 | Supplying and fixing 6 way , Double door, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) |
| 127 | Labour charges for fixing of existing MCB-DB TPN/MCB-DB SPN/TPN Bus Bar chamber/MCCB TPN with enclosure/on surface/ recess including fixing & connections of existing MCBs in the existing MCB DB complete with connections, testing and commissioning etc. as required., interconnections, providing & fixing of fastners, nut bolts etc. as required to complte the job and directed by Engineer-in-Charge. |
| 128 | Supplying and fixing Cable End Box (Loose Wire Box) suitable for For 6way, Double door SPN MCBDB single pole and neutral, sheet steel, MCB distribution board, 240 Volts, on surface/ recess, complete with testing and commissioning etc. as required. |
| 129 | Supplying and fixing Cable End Box (Loose Wire Box) suitable for For 8way, Double door SPN MCBDB single pole and neutral, sheet steel, MCB distribution board, 240 Volts, on surface/ recess, complete with testing and commissioning etc. as required. |
| 130 | Supplying and fixing 63 A, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 131 | Labour Charges for fixing MCB (miniature circuit breaker)of Single Pole in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 132 | Supplying and fixing 32A to 63 A rating, 240/415 V, 10 kA, \"C\" curve, miniature circuit breaker suitable for inductive load of double Pole in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 133 | Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32 A 240 V \"C\" curve DP MCB complete with connections, testing and commissioning etc. as required. |
| 134 | Supplying and fixing 63 A rating, 240/415 V, 10 kA, \"C\" curve, miniature circuit breaker suitable for inductive load of Triple pole and neutralin the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 135 | Supplying and fixing 63A, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 136 | Supplying and fixing of 25mm size of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. |
| 137 | Supplying and fixing 25 mm dia MS flexible pipe with PVC coating along with all ancillaries and accessories like coupler etc. as required. |
| 138 | Supply of 3.5 core 70 sq.mm 1.1KV grade, one number XLPE insulated, aluminium conductor, armoured power cable confirming to latest IS standards. |
| 139 | Supply of 4 core 35 sq.mm 1.1KV grade, one number XLPE insulated, aluminium conductor, armoured power cable confirming to latest IS standards. |
| 140 | Supply of 4 core 25 sq.mm 1.1KV grade, one number XLPE insulated, aluminium conductor, armoured power cable confirming to latest IS standards. |
| 141 | Supply of 4 core 16 sq.mm 1.1KV grade, one number XLPE insulated, aluminium conductor, armoured power cable confirming to latest IS standards. |
| 142 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of size bove 35 sq. mm and upto 95 sq. mm direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. |
| 143 | Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Size: Upto 35 sq. mm (clamped with 1mm thick saddle) :Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp) |
| 144 | Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of size Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)on wall surface as required. Size: Upto 35 sq. mm (clamped with 1mm thick saddle) |
| 145 | Supplying and making end termination with brass compression gland and aluminium lugs of size 3½ X 95 sq. mm (45mm)of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. |
| 146 | Supplying and making end termination with brass compression gland and aluminium lugs of size 3½ X 70 sq. mm (38mm) of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. |
| 147 | Supplying and making end termination with brass compression gland and aluminium lugs of size 4 X 35 sq. mm (32mm) of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. |
| 148 | Supplying and making end termination with brass compression gland and aluminium lugs of size 4 X 25 sq. mm (28mm) of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. |
| 149 | Supplying and making end termination with brass compression gland and aluminium lugs of size 4 X 16 sq. mm (28mm) of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. |
| 150 | Providing and fixing 6SWG dia GI wire on surface or in recess for loop earthing along with existing surface/recessed conduit/submain wiring/cable etc as required. |
| 151 | LED Batten light 24 -26 watt (System lumen efficacy ≥105 <120 lm/Watt):-Supplying, installation, Testing & Commissioning of LED surface mounted Batten light of following body material and construction as per IS : 10322 with driver (Replaceable) as per the requirement with Driver efficiency >85% ,Operating voltage AC 140-270 Volt, freq 50/60 hz, Operating temp range -15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, Flicker free, (flicker should be below 5 %), life time (LED,Driver & electrical circuitary), of minimum 50000 Burning Hours with , 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching)per BISshall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermalmanagement:heatsinkofaluminumhousing such that LED junction temperature shall not rise above 90°C). Powdercoated die cast/ Extrudedaluminium Body (Thickness≥ 1.20 mm) |
| 152 | Supplying of LED Rimless RoundSurface Panel of rating 12W, Color Temp. 6500K, lumens effieciency not less than 100lm/watt, suitable for 230V, 50 Hz, single phase AC Supply, complete as required. |
| 153 | Installation ,Testing, Commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required. |
| 154 | Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal ( Aluminum alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, steel/Al body Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, suitable for operation with regulator for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Ceiling Fan compliant to IS 374:2019 fan Supply, earthing etc. complete as required. Size: 1200mm,service value≥ 6.0 CM/Min/Watt, air delivery 210 CM/Min (Minimum) |
| 155 | Supply of Metallic Body Exhaust Fan of size 300 mm sweep, with G.I. sheet louver shutter, Grey in color,RPM: 900-950, four number blades, Air delivery (minimum) 1145 m3/h, low noise level, suitable for 230V, 50 Hz, single phase AC Supply, complete as required. |
| 156 | Installation of exhaust fan of sizeupto 450 mm sweep in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. |
| 157 | Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes. |
| 158 | Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. |
| 159 | Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required. |
| 160 | Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required. |
| 161 | Providing and laying in position cement concrete of specfied grade excluding the cost of catering and shuttering-All work upto plinth level: 1 : 1½ : 3 ( 1 Cement: coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20mm nominal size derived from natural sources} |
| 162 | Demolishing cement concrete manually / by mechanical means including disposal of material within 50 meters lead as per direction of Engineer-in-charge. Nominal concrete 1:3:6 or richer mix Ii/c equivalent design mix) . |
| 163 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. |
| 164 | Supplying anddrawing of 1x16 sq. mm ISI marked, FRLS PVC insulated, single corecopper conductor cable including connections, copper lugs etc. as required. |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
