|
| 1 | Surface excavation n. exc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil, complete all as specified and directed. |
| 2 | Excavation in trenches n. exc 1.5 m wide and 1.5 m deep or for foundation shafts, wells, manholes cables/poles or similar items n.exc 10 sqm on plan and n.exc 1.5 m in depth and getting outin soft/loose soil, complete all as specified and directed. |
| 3 | Removing of excavated material exc. 50 m and not exc 1.5 km and depositing where directed by the Eng-in-charge, complete all as specified and directed. |
| 4 | M&L for PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete, complete all as specified and directed. |
| 5 | Returning filling in including spreading, levelling, watering and well ramming in layers n exc 25 cm in soft loose soil, complete all as specified and directed. |
| 6 | M&L for brick work with sub class \"B\" bricks (old size bricks) straight or curved on plan exc 6 m mean radius built in cm 1:6, complete all as specified and directed. |
| 7 | M&L for RCC nominal mix 1:2:4, Type B1, using 20mm graded crushed stone aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded for chamfered angles and throating, complete all as specified and directed. |
| 8 | M&L for TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed. |
| 9 | M&L for TMT bars 6 mm dia and up to 8mm dia and including in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed. |
| 10 | Use and waste formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter on flat surface, rough finished, complete all as specified and directed. |
| 11 | S&F mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS.1161-1979 grade St.-240, complete all as specified and directed. |
| 12 | S&F for plates (plain or chequered) channels, Fe 410-W (Gde E- 250) square cut or notched (ordinary and counter sunk) forming holes, without any attachment, complete all as specified and directed. |
| 13 | M&L for reparing new or previously untreated steel surfaces of any description, over 10cm in width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer, complete all as specified and directed. |
| 14 | S&F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws, complete all as specified and directed. |
| 15 | S&F for pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering, fixed with self tapping screws, complete all as specified and directed. |
| 16 | Taking down cement plaster from brick or stone masonry or concrete surfaces and hacking for key and scrubbing down with water etc, complete all as specified and directed. |
| 17 | M&L for rendering, 15 mm thick, in cement mortar 1:6, over brick or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and directed. |
| 18 | M&L for rendering 5 mm thick on RCC ceiling surfaces in cement mortar 1:3 and finished even and smooth without using extra cement, complete all as specified and directed. |
| 19 | M&L for rendering 15 mm thick, in cement mortar 1:4 over brick or concrete surfaces, finished fair and even without using extra cement, mixed with water proofing compound @ 3% by weight of cement, complete all as specified and directed.Note : Integral water proofing compound shall be measured and paid separately. |
| 20 | Supply only integral water proofing compound conforming to IS-2645-1975, complete all as specified and directed. |
| 21 | M&L for preparation of new plastered surfaces of ceiling, chajja etc, including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc. and applying three coats of white wash, complete all as specified and directed. |
| 22 | M&L for preparation of new plastered surfaces and applying two coat of external emulsion paint over 3 mm thick wall care putty, complete all as specified and directed. |
| 23 | M&L for preparation of new plastered surface of wall and applying two coat of oil bound distemper over 3mm thick wall care putty on new plastered surfaces, complete all as specified and directed. |
| 24 | M&L for 75 mm thick PCC 1:3:6 type C-1 (using 20mm graded stone aggregate) as in plinth protection, complete all as specified and as directed. |
| 25 | M&L for hardcore of broken stone of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface, complete all as specified and as directed. |
| 26 | M&L for 100mm thick PCC 1:3:6 type C-2 using 40mm graded crushed stone agg as in sub base, complete all as specified and directed. |
| 27 | M&L for 40mm thick PCC 1:2:4 type B-1 using 20mm graded crushed stone agg as in sub base, complete all as specified and directed. |
| 28 | Dismantling of floor, hearth or wall tiling or stone flooring including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed. |
| 29 | M&L for coloured printed Non - skid Ceramic tiles 7 to 8 mm thick premium quality (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including the chipping of the existing PCC floor, complete all as specified and directed. |
| 30 | M&L for glazed ceramic coloured tiles of (600 x 300mm) x 7-8mm thick premium quality, laid on vertical surfaces such as skirting, dados and risers to steps etc laid over and including 10 mm thick cement plaster in CM (1:4) set and jointed in neat cement paste ofhoney like consistancy and pointed in white or coloured cement to match the shade of tiles, complete all as specified and directed. |
| 31 | M&L for viritified ceramic tiles, 10 mm thick premium quality (square/ rectangular) polished, light shade, area of each tile not exceeding 0.36 Sq.m, laid in floors with neat cement slurry over and including pointing in white cement with pigment to match the shade of tiles, complete all as specified & directed. |
| 32 | M&L for viritified ceramic tiles, 10 mm thick premium quality (square/ rectangular) polished, light shade, area of each tile not exceeding 0.36 Sq.m, laid on vertical surfaces such as skirting, dados and risers to steps etc laid over and including10 mm thick cement plaster in CM (1:4) set and jointed in neat cement paste ofhoney like consistancy and pointed in white or coloured cement to match the shadeof tiles, complete all as specified & directed. |
| 33 | M&L for Screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in cement mortar 1:4, complete all as specified and directed. |
| 34 | M&L for granite (of any type) tiles 18-20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixure of pigment to match the shade of granite stone including cutting and polishing any types, complete all as specified and directed. |
| 35 | M&L for machine cut kota stone slab flooring 20-25mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing, moulding on edge and polishing, complete all as specified and directed. |
| 36 | M&L for Screed bed or bedding layer of mortar 20 mm thick for laying floor finishes in cement mortar 1:4, complete all as specified and directed. |
| 37 | M&L for machine cut kota stone slab in risers/dedos 20-25mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing, moulding on edge and polishing over and including 10mm thick rendering in CM 1:4, complete all as specified and directed. |
| 38 | S&F for powder coated aluminium frames for doors, windows, ventilators & partitions with one or more rebates including jointing cleat for fixing and suitable aluminium powder coated handles, tower bolts and door stopers including fixing to floor with suitable screws/fasteners in partiton etc. complete all as specified anddirected. |
| 39 | S&F for powder coated aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and directed. |
| 40 | S&F for powder coated aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed. |
| 41 | S&F floor door stopper of aluminum alloy body and tongue anodised with drawn steel spring fixed to door with overall length of cover plate 140 mm complete all as specified and directed. |
| 42 | S&F false ceiling with semi perforated 12 mm thick micro tegular edged GRG false ceiling tiles, at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles ofSize 595 x 595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 476 (part 4 )-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main T runners of size 15 x 32 mm of length 3000mm, cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module ofsize 600x 600mm , suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and L shape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall I partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge. |
| 43 | M&L for PVC hollow panelling 5 to 8 mm thick wall panelling any colour/design approved by Engr-in-Charge, inclusive of fixing on to wall incl L Corner, moulding end caps and necessary frame work for fixing and screwing as required, complete all as specified and directed. |
| 44 | Taking down existing water proofing treament any nos of layers and of any description, incl.demolition and taking off PCC padding/plaster on RCC slab,also including removing of bitument coating to show the concrete surfaceto its true colour and roughening etc and also removing the debris outside the MOD land, complete all as specified and directed. |
| 45 | Taking down existing mud puska any nos of layers and of any description, including removing of the debris outside the MOD Land up to distance 250 mtr complete all as specified and directed. |
| 46 | Cutting out cracks to V-section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3 including macthing existing surfaces complete all as specified and directed. |
| 47 | M&L for Cement concrete type B-0, 1:2:4 (12.5 mm graded aggregate) on roof paddingand kerbs in slope finished even and fair, complete all as specified and directed. |
| 48 | M&L for 15 mm thick Screed bed in cement mortar 1:6 mixed with integral water proofing compound @ 3% by weight of cement, complete all as specified and directed. |
| 49 | M&L for laying APP modified membarane with non woven polyester reinforcement mat (concrete core) not less than 3 mm thick & not less than 3.5 kg /sqm, the over the lap torching shall be 100 mm on length side & 100 mm on widthe sideover a tack coat of Industrial bitumen of 1.20 kg / Sqm over Bituminious based primer IS No. 3383@ 250 gms/sqm including apply of Aluminium colour synthetic enamel paint @ 200 gms/sqm all as per manufacture\"s instruction, complete all as specified and directed.Note: Supply only integral water proofing compound shall be measured and paid separately. |
| 50 | M&L for Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring into brick wall etc. and making good, cutting exceeding 20cm girth complete all as specified and directed. |
| 51 | Taking up or down 15 mm bore steel tubing with connections or fittings from wall, ceiling and floor etc., including cutting/chasing in wall/floor and removal from site, complete all as specified and directed by the Engineer in Charge. |
| 52 | Taking up or down 20 mm bore steel tubing with connections or fittings from wall, ceiling and floor etc., including cutting/chasing in wall/floor and removal from site, complete all as specified and directed by the Engineer in Charge. |
| 53 | S&F for 15mm bore GI tubes medium grade with all fitting and fixed to walls and ceiling or laid in floor, complete all as specified and directed. |
| 54 | S&F for 20mm bore GI tubes medium grade with all fitting and fixed to walls and ceiling or laid in floor, complete all as specified and directed by Engineer-in-Charge. |
| 55 | S&F for 20 MM Gun-metal, globe or gate valve, with iron wheel head, screwed both ends for iron pipe and all as specified and directed by Engr-in-Charge |
| 56 | S&F for 20 mm bore Ball brass valves, high pressure, with polythene float and flynut, screwed for iron pipe or brass ferrule, complete all as specified and directed. |
| 57 | S&F for rotational moulded polyethylene water storage tanks tipple layer (cylinderical, vertical with closed top) of 1000 Ltrs capacity hoisted and fixed in position all as specified and directed as per SSR Pt- I, complete all as specified and directed. |
| 58 | S&F for wash basins, vitreous china, white, counter sunk of size 550 x 400mm including 32 mm dia waste fittings, chromium plated, brass with long screwed shanks, fly nuts and waste pipe of 32 mm dia, complete all as specified and directed. |
| 59 | S&F for vitreous china wash down water closet, pedestal pattern (EWC), white, with \"P\" or \"S\" trap, with PVC water closet seat, black or white, closed pattern, with flat bottom and cover and mild steel chromium plated or aluminised hinging device, complete all as specified and directed by Engr-in-Charge. |
| 60 | S&F in repair 10 Litre PVC low level flushing cistern complete with syphonic action type, white, with inlet, ball valve, float and handle connecting to ITWC/ETWC and fixing on walls with brackets complete all as directed. |
| 61 | S&F for PVC connection 15 mm bore 450 mm in length, complete all as specified and directed. |
| 62 | S&F for brass chromium plated wall mixer for mixing hot & cold water screwed down for iron pipe and fixed, complete all as specified and directed. |
| 63 | S&F 15mm chromium plated swivel shower rose of size 125mm dia with or without swivel joints sny size for fixing with 15 mm pipe incl shower arm 15 mm size, 195 mm long with bend of 45 degree, complete all as specified and directed. |
| 64 | S&F for brass CP soap dish of approved quality, complete all as specified and directed. |
| 65 | S&F PVC 110 mm (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with clamps and for sewage line, complete all as specified and directed. |
| 66 | S&F PVC 75 mm (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with clamps and for sewage line, complete all as specified and directed. |
| 67 | S&F PVC 75 mm (SWR) bends any radius, complete all as specified and directed. |
| 68 | S&F PVC 100 mm (SWR) bends any radius, complete all as specified and directed. |
| 69 | S&F PVC (SWR), junction single, (Single T) equal or unequal 75 mm, complete all as specified and directed. |
| 70 | S&F PVC (SWR), junction single, (Single T) equal or unequal 110 mm, complete all as specified and directed. |
| 71 | S&F for 100mm dia, cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), complete all as specified and directed. |
| 72 | S&F for 15 mm angle valve chromium plated, fancy type with wall flange with high pressure screwed down and with CP flange of same make, complete all as specified and directed. |
| 73 | S&F for 15mm bore fancy type, chromium plated bib taps long body cast copper alloy with crutch or butterfly handle, screwed for iron pipe or brass ferrule, complete all as specified and directed. |
| 74 | S&F for looking mirror 600x450mm bevelled edges of selected quality glass mounted on 6mm commercial ply or AC building board with aluminium frame around and fixed to wooden plugs with CP brass screws, complete all as specified and directed. |
| 75 | S&F for brass chromium plated towel rail 600mm long(ofapproved shade) fixed as in repair, complete all as specified and directed. |
| 76 | S&F in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm, complete all as specified and directed. |
| 77 | S&F for curtain rod Stainless steel 25 mm dia 1mm thick with pairs of fixing fancy type brackets heave grade, Fancy type supprting stops heavy grade, rollers including screws with required accessories and finishing the surface with existing wall surface etc, ccomplete all as specified and directed. |
| 78 | Taking down chowkhats or frames with shutters not exc. 1.5 Sqm each (without taking off shutters from the frames) complete all as specified and directed. |
| 79 | Taking down chowkhats or frames with shutters exc 1.5 Sqm but not exc. 4 Sqm each (without taking off shutters from the frames) complete all as specified and directed. |
| 80 | S&F for factory made Solid WPC Door frame size (45mm x 85mm Single Rebate) made from 100% LEAD FREE (single extruded process) material with density 780 kg/Cum & Manufactured by an ISO: 9001-2015 certified company, all as per specification drawings including all necessary assories as directed by the Engineer-In-Charge.The door frame should be Water Proof, Termite Proof, Fire Retardent and having excellent screw holding capacity. |
| 81 | S&F for factory made Solid WPC Door frame size (100mm x 65mm Single Rebate) made from 100% LEAD FREE (single extruded process) material with density 780 kg/Cum & Manufactured by an ISO: 9001-2015 certified company, all as per specification drawings including all necessary assories as directed by the Engineer-In-Charge.The door frame should be Water Proof, Termite Proof, Fire Retardent and having excellent screw holding capacity. |
| 82 | S&F for factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class \"A\" category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary S S screws shall be paid separately), complete all as sprceified and directed by Engr-in-Charge. |
| 83 | S&F for Butt hinges medium weight cold rolled steel of 100 mm size and fixed, complete all as specified and directed. |
| 84 | S&F for aluminium handles, cast type anodised of 150 mm size, complete all as specified and directed. |
| 85 | S&F for aluminum anodizes barrel tower bolts of extuded section and fixed of 200 mm size, complete all as specified and directed. |
| 86 | S&F for aluminum alloy, anodized, door bolt with hasp staple (bolt type) and fixing clips of sheet,cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy and fixed length of bolt 250 mm, bolts not less than 16mm dia with and including a minimum of 6 bolts not,four on bolt plate and two on staple plate complete (ISI marked ), complete all as specified and directed. |
| 87 | S&F of door closer hydraulically regulated design No 3, universal type, suitable for door shutters of 851 to 1000m in width and weifht between 61 to 80 kg etc complete all as specified and directed. |
| 88 | S&F of Mortice lock vertical type 4 lever etc complete all as specified and as directedetc, complete all as specified and directed. |
| 89 | M&L for 18-19mm thick water proof solid MDF Board prelaminated both sides of approved shade fitted with necessary arrangement as in kitchen cabinet back sides, partition, shutters and shelves,etc., fixed with solvent cement adhesive and stainless steel screws and providing 1mm thick PVC lipping to exposed edges, complete all as specified and as directed. |
| 90 | S & F for 30 mm Continuous (piano) hinges, mild steel, bright finish or elec trogalvanised, complete all as specified and directed. |
| 91 | S&F for Magnetic catcher suitable for kitchen cabinet shutters, complete all as specified and directed. |
| 92 | S&F for 100 mm Hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws, complete all as specified and directed. |
| 93 | S&F in repair Toilet paper holder of brass, chromium plated fixed to walls with chromium plated (CP) brass screws complete all as directed. |
| 94 | S&F for venetian blind for window including necessary accessories required for fix to wall, complete all as specified and directed. |
| 95 | M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., incl welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed. |
| 96 | Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level) including floor finishes/tiling work and disposal of debris, complete all as specified and as directed. |
| 97 | M&L for 75mm thick PCC type D-2, 1:4:8 (using 40mm graded aggregate) as in sub base,complete all as specified and as directed. |
| 98 | M&L for 60 mm thick machine cut precast concrete inter locking paver block factory made with grey cement and pigment, (M-35) grade any clours as approved by EIC /GE, complete all as specified and directed. |
| 99 | All as per item No 98 above but except inter locking paver block. |
| 100 | M & L for sand filling under floors or in foundationincluding watering and consolidation, complete all as specified and directed. |
| 101 | M&L for 50 mm thick PCC 1:3:6 type C-2 (using 40 mm graded stone agg) as in plinth protection / path/ any paved area, complete all as specified and directed. |
| 102 | M & L for chequered tiles of size 300 x 300 x 25 mm thick (colour and glazed approved by EIC) with grey cement and pigments laid over 15 mm thick screed bed in CM 1:6 bedded and jointed in neat cement slurry, incl dismantling complete all as specified and directed. |
| 103 | Dismantling of AC/GI sheet (corrugated, semi corrugated etc) of any thickness incl ridges hips valleys as in roof coveringscomplete all as specified and directed. |
| 104 | Dismantling wrought Iron or mild steel work of any description not otherwise provided for wind tie complete all as specified and directed. |
| 105 | S&F for PVDF aluminium composite panels with fire resistent mineral filled core material as in interior/exterior wall cladding on external wall surface shall consist of following :- (i) Aluminium sheet making a total panel thickness of 3 mm with outer surface finished with PVDF based coating 0.25mm, inner surface finished with a thin coat of polyster paint. The cleness of aluminium cover sheet shall be 0.50 mm inner core shall be of LDPE. (ii) MS tube framing of section 25mm x 50mm x 1.50mm thick.(iii)MS tube grid shall not be exceed 1.0 sqm each the aluminium grid not more than 1 mtr c/c shall be fixed with MS angle 30x30x5 mm projected 150mm from surface of wall.(iv)Colour shall be approved by GE. (v)Joint shall be sealed with silicon weater proof sealing compound with help of masking Tapes.Note : Canopy, borders, projections etc will be measured in sqm for payment purpose. |
| 106 | S&F for Acrylic letters (English/Hindi) 300 mm high, 50 mm width and 3 mm depth hollow wall fixed on walls fixed on wall surface or or 3mm ACP sheets board of any description using stainless steel screws of suitable size or best quality adhesive including LED module rain proof lights fittings in each letters, complete all as specified and directed. |
| 107 | M&L for point wiring with colour coding multistranded copper conductor cable,PVC insulated and unsheathed size 1.5 sqmm with PVC concealedConduit( dia not les than 25 mm) with fixing accessories for one light /fan/bell point controlled by one switchwith pressed steel concealed terminal boxes coveredwith 3mm thick laminated sheet incl. contineous earth wire of PVC insulated unsheathed multi stranded copper conductor cablesize 1.5 Sqmm for earth wire connected to common earth dolly complete all as specified and directed. |
| 108 | All as per item No 107 above but for one 3/5 pin somet 5 Amp on same board with 1.5sqmm wire with 1.5sqmm earth wire |
| 109 | All as per item No 107 above but power point wiring (concealed) with 2 5 sqmm single core pvc insulated FRLSH unsheathed cable with stranded copper conductor for one switch socket outlet, 5/15 Amps multipurpose on independent modular plate including pvc unsheathed copper conductor of same dia as earth wire complete all as specified and directed. |
| 110 | M&L for wiring for circuit /submain wiring along with earth wire the following size of PVC insulated FRLSH cooper conductor single core cable in surface/recessed 2x4 0 samm+ 1x2 5 scmm earth wires required complete all as specified and directed. |
| 111 | S&F Modular switch 6 Amps, one way 230 Volts AC complete all as specified and directed. |
| 112 | S& modular socket 6A-2/3 pin combined 2 module complete all as specified and directed. |
| 113 | S&F modular switch socket combination 16A, 6 pin, 3 module complete all as specified and directed. |
| 114 | S&F Celling rose, PVC / Polycarbonate isolated body surface backlite, 65x50mm, three terminals, 230 Volts AC complete all as specified and directed. |
| 115 | S&F Ceiling fans, complete with blades, down rods. electronic regulator and accessories, 230 V, 1200 mm sweep Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with BLDC motor, complete all as specified and directed. |
| 116 | S&f modular fan step regulator 120 W -2 module complete all as specified and directed. |
| 117 | S&F exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230 V, 50 Hz, RPM 1200, copper winding of sweep 250mm, complete all as specified and directed. |
| 118 | S&F single pole and neutralsheet metal enclosure with a two pin and earth plug and socket complete with one single pole 20 ampsMCB complete all as specified and directed. |
| 119 | S&F LED luminaire 600mm X 600mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed. |
| 120 | S&F LED tube light fittings 20W (4 feet) wall mounted LED batten extruded PVC heat sink provided for efficient heat dissipation & integrated electronic driver optics diffused complete including electrical connection with copper cable from ceiling rose to fittings and complete all as specified and directed. |
| 121 | S& sheet metal enclosure MCB type DB suitable VTPN 4 way 200 Amps rated bus bar double door type complete all as specified and directed. |
| 122 | S & F in repairs single pole and neutral sheet metal enclosures for Distribution board (DB\"s)suitable for MCBs fitted with bus bar, Neutral link Earth Bar and Din rail 240 V, 50 Hz supply double door SP&N DB system 12 ways complete all as specified and directed. |
| 123 | S&F white cover plate with frame with 3 module complete all as specified and directed. |
| 124 | S&F modular metal flush box 6 module complete all as specified and directed. |
| 125 | S&F modular metal flush box 8 module complete all as specified and directed. |
| 126 | S& modular metal flush box 3 module complete all as specified and directed. |
| 127 | S&F modular metal flush box 6 module complete all as specified and directed. |
| 128 | S&F MCCB 3 pole, 415 V, fixed type, 25 to 100 Amps with breaking capacity 16 KA. 240 V, complete all as specified and directed. |
| 129 | S&F MCB TPN capacity 40-100 Amps, 240 V, complete all as specified and directed. |
| 130 | S&F MCB SP 06 to 32 Amps 240V incl all termnials, fitting etc including taking down, complete all as specified and directed. |
| 131 | M & L for earthing complete with galvanised steel earth plate electrode 600 × 600 × 6.3 mm thick burried directly in gorund (earth pit not less than 2.25 Mtr normal ground level), and top edge of earth plate not less than 1.5 mtr below normal ground level, connected to galvanised means of earth wire 4 mm dia with bolts, nuts & check nuts, and washers of galvanised iron protection pipe light grade of 15mm dia and watering pipe medium grade of 20 mm dia and filled with alternate layer of charcoal and common salt, watering funnel with wire mesh, earth pit chamber and cover Cl frame PCC 1:3:6 type C-2 all as shown in electrical plate No-3 of SSR part-l of 2009 connected to earthing test point all as specified and indicated including all earth work excavation, returning filling and disposal of surplus soil and testing on completion, complete all as specified and directed. |
| 132 | M&L for, connecting and testing XLPE underground cableinsulated,PVC bedded,glvanisedstrip or wire armoured electric power cable heavy duty with 1100 volts grade with stranded aluminium conductor inclusive connected to thimbles, nut bolt by crimping tool etc complete of size 70 sqmm 4 core, complete all as specified and directed. |
| 133 | M&L for sand cushoning with a layer of sand 80mm thick before laying of cable and 150mm thick after laying of cable to trenches complete all as specified and directed. |
| 134 | M&L for sub class `B` bricks for cable protection complete all as specified and directed. |
