|
| 1 | MCCB ,DISTRIBUTION BOARDS, MCB\"s, RCCB\"s, CHANGE OVER etc. Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work. 4 pole MCCB 6 amp to 100 amp, 25 KA |
| 2 | 4 pole MCCB 125 to 160 amp, 25 KA |
| 3 | 4 pole MCCB 300 to 400 amp, 50 KA |
| 4 | Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to to the entire satisfaction of the Engineer-in-Charge of the work.TPN DB Horizontal type Double Door 6 way ( 8 incoming 3phase*6 outgoing) |
| 5 | Supply and erection of miniature circuit Breaker/isolator 240/415 V in the existing distribution board including making necessary connections:- 6 amp. to 32 amp Single Pole |
| 6 | 40 amp to 63 amp. Double pole |
| 7 | 40 amp to 63 amp. MCB\"s Four Pole |
| 8 | Supply, installation, testing and commissioning of load bank with digital meter module cost of digital Amp./ volt meter with selector switch wiring (but EXCLUDING COST of incoming and outgoing MCCB’s) etc. suitable for operation of 240/415 volts A.C. Supply with both side cable allay, inter connection and fixing the same in existing MS pedestal/ wall complete with all labour and material required for the same up to the entire satisfaction of Engineer-in charge of work. Load Bank 8 way 400 A |
| 9 | Supply and election of Goodridge Almirante type M.S. pedestal made of 50 mm *50 mm * 6 mm angle Iron frame with 3.00 mm thick M.S. sheet covering including shutters with suitable hinges and looking arrangement with the Godrich type handle including round bars. The to covering should have a downward overhang of 75 mm on all sides of pedestal, having two sets of water proof ventilation holes of suitable size on the sides, at top and bottom, Each set containing four No’s. holes to discharge the heat produced by suitable size to make it water proof . The pedestal duly painted both inside and outside with two coats of approved paint and primary coat and its legs are embedded upto the entire depth in 1:2:4 cement concrete block, projected 75 mm all around the pedestal and 200 mm above the ground level including the cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in charge of the work.M.S. pedestal of size 1200 mm wide, 1500 mm high, 450 mm deep and bottom totally open , duly embedded in cement concrete block of size 1350 mm*600 mm*200 mm above ground level , having a base of size 1500 mm* 750 mm* 250 mm below ground level. |
| 10 | EARTHING AND LIGHTENING ARRESTOR Earthing with G.I. earth pipe 4.5 m long and 40 mm dia with masonry enclosures on the top etc. (but without charcoal or coke and salt) as required. |
| 11 | Extra for using salt and char coal/coke for pipe earth electrode as required. |
| 12 | Supplying and laying 25mm x 3 mm G.I. strip in 40 mm dia,GI pipe as/from earth electrode including soldering etc. as required. |
| 13 | Providing and fixing 25 mm x 3mm G.I. strip on surface or in recess for connections etc. as required with all labour and material. |
| 14 | Providing and laying earth connections from earth electrode with 4.00 mm dia G.I. wire in 15 mm dia G.I. pipe from earth electrode as required. |
| 15 | Providing and fixing 4.00 mm dia G1. Wire on surface or in recess for loop earthing as required. |
| 16 | LT CABLE Supply and erection of aluminium lugs heavy duty including crimping etc. upto the entire satisfaction of the Engineer-in-charge of the work.16 sqmm |
| 17 | 25 sqmm |
| 18 | 35 sqmm |
| 19 | 95 sqmm |
| 20 | STREET LIGHT Supply and erection of Three Phase weather proof M.S. box of size 30 cm x 20 cm x 15 cm with hinged cover made of 2 mm thick MS sheet, locking arrangements, housed in wall/fixed on pole , including the cost of 1 no 4 way 16 A bakellite connector, 1 no. 16 amp TP MCB and 4 Nos. 16 amp. neutral links fixed on bakellite sheet in the M.S. box and necessary connections. |
| 21 | Supply and erection of Hot Dip Galvanized octagonal pole of 3mm thickness, with base plate including cost of nut and bolts , earthing studs, Integral Cable termination arrangement 5 mm thick Bakelite base plate on suitable welded MS/GI bracket 32 A four way connector 2 no 1 O A SP MCB , end cover and all accessories as supplied by the manufacture including Providing RCC foundation of M25 grade (1 Cement:1 Stone aggregate: 2 Coarse sand) i/c excavation, steel reinforcement (Fe 500) @80 kg/cum of concrete contents, concrete cover 50mm, anchor bolts etc. over a bed of PCC 1 :5: 1 O of required dimensions for octagonal poles of various heights as per following specifications complete in all respects and as per directions of Engineer-in-charge 7 Mtr Long pole with top dia 75 mm and bottom dia 150 mm with base plate of size 300 x 300 x 20 mm |
| 22 | MISCELLANEOUS ITEMS S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Mtr below ground level including diging and refilling of earth including cost of suitable size socket/cuppler for HDPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work. DWC/HDPE pipe 50/40 mm outer dia/ inner dia |
| 23 | RCC FOUNDATIONS FOR OCTAGONAL POLES Providing RCC foundation of M25 grade (1 Cement:1 Stone aggregate: 2 Coarse sand) i/c excavation, steel reinforcement (Fe 500) @ 70 kg/cum of concrete contents, concrete cover 50mm, anchor bolts etc. over a bed of PCC 1:5:10 of required dimensions for octagonal poles of various heights as per following specifications complete in all respects and as per directions of Engineer-in-charge 3m high pole |
| 24 | 7m high pole |
| 25 | Providing & erection/ laying of PVC/ XLPE insulated underground aluminium conductor underground cable loose in existing pipe or trenches complete in all respect with necessary connection upto the entire satisfaction of engineer in charge of the work. 16 Sq mm 2core (Arm.) |
| 26 | 16 Sq mm 4 core (Arm.) |
| 27 | 95 Sq mm 3.5 core (Arm.) |
| 28 | Providing & erection/ laying of PVC/ XLPE insulated underground aluminium conductor underground cable on surface/ existing cable tray complete in all respect with necessary connection upto the entire satisfaction of engineer in charge of the work 16 Sq mm 2core (Arm.) |
| 29 | 16 Sq mm 4 core (Arm.) |
| 30 | 95 Sq mm 3.5 core (Arm.) |
| 31 | LED Street light fixture, powder coated pressure die cast aluminium body (System lumen efficacy ≥105 <120 lm/Watt) Supplying, installation, Testing & Commissioning of Street light LED fixture powder coated pressure die cast aluminium body with driver as per the requirement with Driver efficiency >85%, Input voltage: 140-270 Volt AC, frequency 50/60 hz, Operating temp range -5 0C to 50 0C, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency >85%,THD < 10% as per IEC 61000-3-2, P. F.≥0.95, IP-66,IK-10, CRI >70, under voltage and over voltage protection, EMIEMC As per CISPR -15, lenses for beam angle as per IESNA type I/II/III as per the width of the road and the project requirement., suitable to fit in up to 65mm dia pipe, life time (LED, Driver & electrical circuitry) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin),SDCM (Standard Deviation Colour Matching) <5, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard complete in all respect i/c external connections with 1.5 sq.mm FRLS/HFFR,PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥105 <120 lm/Watt output.LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by other specifications as per DNIT in PDF. temperature shall not rise above 90°C). Make Mayfair Lighting / Surya/ Bajaj 90 watt |
| 32 | LED Flood Light, powder coated pressure die cast aluminium (System lumen efficacy ≥105 <120 lm/Watt). Supplying, Installation, Testing & Commissioning of Flood Light, powder coated pressure die cast aluminium body with built in or separate driver as per the requirement with Driver efficiency >85%, Input voltage: Input voltage: 140-270 Volt AC, frequency 50/60 hz, Operating temp range -5 0C to 50 0C, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency >85%,THD < 10% as per IEC 61000-3-2,P. F.≥0.95, IP-66,IK-10, CRI >70, under voltage and over voltage protection, EMI-EMC as per CISPR -15, lenses for beam angle 30 deg-120deg as per the application and the project requirement., suitable tilt able fitting, life time (LED, Driver & electrical circuitry) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K /4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <5, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥105 <120 lm/Watt output. LM79 & LM80 Test report and all testing required for LED other specifications as per DNIT in PDF. 90°C). Make Mayfair Lighting / Surya/ Bajaj 150 watt |
| 33 | Supply and erection of 8W LED spike light fixture made of die cast aluminium housing fitted with aluminium spike with - Philips/ Fulham/ HR Driver complete in all respect upto entire satisfaction of Engineer - In- Charge. Make Mayfair Lighting / Surya/ Bajaj |
| 34 | Supply and erection of 10 W LED Bollard fixture made of cast aluminium fitted with polycarbonate diffuser with - Philips/ Fulham/ HR Driver complete in all respect upto entire satisfaction of Engineer - In- Charge. Make Mayfair Lighting / Surya/ Bajaj |
| 35 | Supply and erection of 6 W in-ground LED light in aluminium die casting fitted with stainless steel ring and toughened glass cover with - Philips/ Fulham/ HR Driver complete in all respect upto entire satisfaction of Engineer - In- Charge. Make Mayfair Lighting / Surya/ Bajaj |
| 36 | Supply and erection of 7 W LED step light fixture made of die cast aluminium with - Philips/ Fulham/ HR Driver complete in all respect upto entire satisfaction of Engineer - In- Charge. Make Mayfair Lighting / Surya/ Bajaj |
| 37 | Supply and erection of Single arm. G.I. Bracket made of 50 mm dia G.I pipe B class ISI 1.5 mtr. long with 25 mm dia G.I. bottom pipe with 75 mm dia 60 cm. long G.I. collar pipe, top covered with ornamental cap duly welded, painted 2 coats of aluminium paint on bracket and golden paint on ornamental cap including erection of same with all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-In - charge of work. |
| 38 | Supply and erection of 1.5 Sq. mm 2 Core copper PVC insulated and FR PVC round sheathed, copper conductor flexible industrial cable two core 1100 volts grade in pipe of suitable size excluding cost and erection of pipe complete in all respect upto the entire satisfaction of Engineer in charge of the work. |
| 39 | Supply of 8 mtr decorative poles made of galvenised Mild steel Pipes in 3 sections with cast aluminium embellishment duly polyurethane paint coated. Bottom Dia - 139.7(2m) Middle Dia - 88.9 (3m) Top Dia - 300x300x16 mm , MFMD - 114 , with Foundation Bolts -24x750x4 Nos. , with - 4 light bracket -MF-30 comlete in all respect upto entire satisfaction of Engineer-In-charge of work. Make : Mayfair lighting/Surya/Bajaj Please Enable Macros to View BoQ information |
