Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Taking down cement or cement lime plaster, any description on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc. Complete all as specified and directed. |
| 2 | M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces of wallin CM 1:6 and to be finished even and smooth (without using extra cement) complete all as specified and directed. |
| 3 | M&L for 5mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:3 as in ceiling complete all as specified and directed. |
| 4 | M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces of wallin CM 1:4 and to be finished even and smooth (without using extra cement) complete all as specified and directed. (WPC measured and paid seperately) |
| 5 | Supply only integral waterproofing compound |
| 6 | Demolition of brick work or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc., but excluding ashlar facings, dressed stonework & precast concrete articles. Complete all as specified and directed. |
| 7 | M&L Brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in 1:6 cement mortar. Complete all as specified & directed. |
| 8 | M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls, built in 1:4 cement mortar. Complete all as specified & directed. |
| 9 | M&L 75mm thick PCC type C-2, (1:3:6) using 40mm graded stone aggregate as in plinth protection finished even & smooth without using extra cement complete all as specified and directed. |
| 10 | M&L Forming 12mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm primed andsealed with sealing compound, Grade ‘A’ complete all as specified and directed. |
| 11 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store & rubbish off the premises complete all as specified and directed. |
| 12 | Demolition of cement concrete (un-reinforced) in ground floor and paving not exc 15 cm thick above or below ground level and removalof entire debris as ordered outside MD land complete all as specified and directed. |
| 13 | M&L for Cement Concrete Type C-2, 1:3:6 (using 40 mm graded brick coarse aggregate) as in sub base, floors, filling & mass concrete complete all as specified and directed. |
| 14 | M&L for Vitrified tile flooring 9-10mm thick (square/rectangular) area of each tile exceeding 0.42 Sqm but not exceeding 1.00 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles laid over & including 15 mm thick screed bed or bedding layer of 1:6 cement mortar complete all as specified and directed. |
| 15 | All as per item No 14.00 here-in-before as in skirting/dado & including rendering 10 mm thick in cement mortar 1:4 complete all as specified and directed. |
| 16 | M&L for Non Skid coloured ceramic tiles of design as approved 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles laid over & including 15 mm thick screed bed or bedding layer of 1:6 cement mortar complete all as specified and directed. |
| 17 | M&Lfor Glazed coloured ceramic tiles 350 x 250 x 7 mm / 450 x 350 x 7 mm thick in vertical surface such as dado / skirting / risers to steps etc., set & jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including rendering 10 mm thick in cement mortar 1:4. Complete all as specified and directed. Note- (i) The size of tiles (except thickness) may be varied during execution without any price adjustment. |
| 18 | Demolition of stone slabs and tiles of any description or thickness laid bedded and pointed in any mortar in floors, aprons etc complete all as specified and directed. |
| 19 | M & L Granite (Black/Ruby Red ) work (table rubbed and polished)20 mm thick n steps, jambs, pillars, window-cills, wash basin, cooking platforms and including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite bedded and jointed with grey cement slurry and pointed to match the shade of granite stone grindingand polishing types including screed bed 15 mm thick in CM 1 : 6 complete all as specified and directed. |
| 20 | M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform & other similar situations complete all as specified and directed. |
| 21 | Taking down chowkhats or frames not exc. 1.50 sqm each with shutters (without taking off shutters from the frame) and removing to store complete all as specified and directed. |
| 22 | Taking down chowkhats or frames exc. 1.50 sqm but not exc. 4 sqm each with shutters (without taking off shutters from the frame) and removing to store complete all as specified and directed. |
| 23 | S & FFactory made single extruded WPC (Wood Polymer Composite) solid door frame of size45 x 85mm comprising of virgin PVC polymer of K value 58-60 (suspension grade), calcium carbonate and natural fibre (wood powder/rice husk/wheat husk) and non tixic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC slovent cement and screwed with full body threaded star headed SS screws havng minimum frame density of 750 Kg/cum, screw withdrawal strength of 2200 N (face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticty 900 N/mm2 and resistance to spread of flame of Casss A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and directed (M.S hold fast/lugs or SS dash fasteners shall be paid for seperately.Note : For WPC solid door minus 5mm tolerance in dimension i.e depth and width of profile shall be acceptable.Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 24 | S&F, Factory Made Solid PVC Moulded Door Shutters with wood free EPS 28 to 30 mm thick (stile:), with 2,4 or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face withParticle Board Coreboard core, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed. |
| 25 | S&F Powder Coated (minimum thickness of powder coating 50 micron) Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed. |
| 26 | Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed. |
| 27 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door frame of size 125 x 65mm comprising of virgin PVC polymer of K value 58-60 (suspension grade), calcium carbonate and natural fibre (wood powder/rice husk/wheat husk) and non tixic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC slovent cement and screwed with full body threaded star headed SS screws havng minimum frame density of 750 Kg/cum, screw withdrawal strength of 2200 N (face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticty 900 N/mm2 and resistance to spread of flame of Casss A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and directed (M.S hold fast/lugs or SS dash fasteners shall be paid for seperately.Note : For WPC solid door minus 5mm tolerance in dimension i.e depth and width of profile shall be acceptable.Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 28 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35 mm thick decorative typecomprising ofvirgin polymer of K value 58-60 (suspension grade), calcium carbonate and natural fibre (wood powder/rice husk/wheat husk) and non tixic additives(maximum toxicity index of 12 for 100 gms)having minimum density of 650 Kg/cum andscrew withdrawal strength of 1800 N (face) & 900 N (Edge), minimum compressive strength of 50 N/mm2, modules of elasticty 850 N/mm2 and resistance to spread of flame of Casss A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessay full body threaded star headed counter sunk S.S screws complete all as specified and directed. Note : stainless steel butt hinges and necessary S.S screws shall be paid separately. |
| 29 | S & Fin repairFactory made single extruded WPC (Wood Polymer Composite) solid plain skeleton door shutter of 35 mm thick decorative type comprising ofvirgin polymer of K value 58-60 (suspension grade), calcium carbonate and natural fibre (wood powder/rice husk/wheat husk) and non tixic additives(maximum toxicity index of 12 for 100 gms)having minimum density of 650 Kg/cum andscrew withdrawal strength of 1800 N (face) & 900 N (Edge), minimum compressive strength of 50 N/mm2, modules of elasticty 850 N/mm2 and resistance to spread of flame of Casss A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hingesof required size with necessay full body threaded star headed counter sunk S.S screws including and tainless steelwire cloth 0.36 mm nominaldia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanized wire staples beads complete all as specified and directed. Note : Stainless steel butt hinges and necessary S.S screws shall be paid separately. |
| 30 | S&F Providing and fixing of double rebate openable/fixed windows (Eco 4000) made of galvanized steel colour coated/powder coated (base steel as per IS 513 of “D\" quality, galvanized as per IS 277 with zinc of 120 grams/sqm) with total thickness of coating 0.58 mm, primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer 5-7 microns thick or powder coated with pure polyester powder up to 50-60 microns thick, outer frame section 72 x 55 mm, centre mullion section 72 x 50 mm, shutter section 47 x 20 mm,fly mesh section 40 x 20 mm and the fixed glass beading section 12 x 12 mm, outer frame and mullions shall consists rebate for glazed shutter, fly mesh and 20 mm provision for guard bars/grills, the sections cut to length mitre joined with corner bracket, centre mullions fixed with mullion cap, stay, handles, latch, 2 Nos of heavy duty stainless steel pivot hinges per shutter and panelled with 4 mm thick plain clear glass and S.S. Mesh for fly mesh shutter (304 grade), fitted using EPDM (Ethyl Propylene Diamine Monomer) gaskets including fixing windows in the concrete/masonry wall by means of self-expanding screws, including 10mm Square bars welded to 6x12mm flat at a distance 150mm c/c (pitch) etc. complete all as specified and directed. |
| 31 | M&L for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 32 | S&F in repair, 18/19 mm thick, high density PVC/WPC solid fibre board with both sideprelaminated PVC sheet as Kitchen and bed room cupboard shutter and frame and inside shelves and side walls complete all as specified and directed. |
| 33 | S & F Sheet glass 4.8 mm thick ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed. |
| 34 | M&L PCC in lintels upto 1.5 m clear span, cills, steps; seismic & other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded for chamfered angles and throating, as directed type B1 (1:2:4) using 20 mm graded aggregate including necessary formwork complete all as specified and directed. |
| 35 | Forming jambs, etc., to openings, including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, built in CM(1:4) or cement lime mortar (1:2:9) complete all as specified and directed. |
| 36 | S&F Butt hinges medium weight cold rolled Aluminium anodised 100mm long complete all as specified and directed. |
| 37 | S&F stainless steel Butt hinges 100mm long complete all as specified and directed. |
| 38 | S&F Aluminium anodised barrel tower bolts of extruded section 150mm long complete all as specified and directed. |
| 39 | S&F Aluminium handles cast type anodised of 150mm complete all as specified and directed. |
| 40 | S&F300mm Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete all as specified and directed. |
| 41 | S & Fin repair helical Door spring ordinary rat tail rod pattern springs including roller and roller plate complete of mild steel 300 mm long complete all as specified and directed. |
| 42 | S&F mmContinuous (piano) hinges, 40 mm (width of flaps) (when open) mild steel, bright finish or electrogalvanised complete all as specified and directed. |
| 43 | S&F Hasp and staple,aluminium anodised, wire type, stove enamelled black, including bolt to hingeplate and fixed with screw Size of hasp and staple is 150 mm complete all as specified and directed. |
| 44 | S&F magnetic catcher with nut and screw of mild steel bright finish complete all as specified and directed. |
| 45 | M & Lfor ATT Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floorscomplete all as specified and directed. |
| 46 | M & Lfor ATT treatment to the soil under plinth protection at the rate of 5 litres of emulsion per sqm of surface complete all as specified and directed. |
| 47 | S&F in repairs 25 mm dia stainless steel curtain rod chromium plated including fancy type brackets fixing with fixing fancy type bracket stops rollersetc complete all as specified and directed. |
| 48 | M&L for preparation of new or previously untreated steel surfaces of any description, over 10 cm in width or girth, not otherwise described & applying two coat of synthetic enamel paint (ordinary tint) over & including one coat of red oxide, zinc chrome primer complete all as specified and directed. |
| 49 | M&L for preparation of newly plastered or unplastered brick work or concrete surfaces & applying two coats of oil bound distemper over a coat ofprimer over a coat of 1-2mm thick birla wall care putty complete all as specified and directed. |
| 50 | M&L for preparation of old decorated surfaces of walls bycomplete removal of existing treatment and applying two coat of oil bound distemper over a coat of primer over a coat of 1-2mm thickbirla wall care putty complete all as specified and directed. |
| 51 | M&L for preparation of new decorative surfaces of wall of wallsincluding, cornices (plastered or unplastered)of any description, rubbing, scrappingby hand held sander / long handle sander and Jet pressure washing and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resisitance as per IS 15489:2004, alkali & fungal resistance dirt resistance exterior paint (Apex -Ultima Protek) of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over newsurfaces including filing undulations with white cement based putty mixed with multi purpose mixer complete all as directed. |
| 52 | M&L complete removal of existing any type oftreatment of wallsincluding, cornices (plastered or unplastered)of any description, rubbing, scrappingby hand held sander / long handle sander and Jet pressure washing and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resisitance as per IS 15489:2004, alkali & fungal resistance dirt resistance exterior paint (Apex -Ultima Protek) of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over oldsurfaces including filing undulations with white cement based putty mixed with multi purpose mixer complete all as directed. |
| 53 | M&L for applying two coat of oil bound distemper over & including one coat of alkali resistant priming paint on newly prepared plastered ceiling surface complete all as specified and directed. |
| 54 | M&L for preparation of old surfaces of any description and applying oil bound distemper over & including one coat of alkali resistant priming paint on prepared ceiling on old decorated surfacesincluding filling cracks and holes etc complete all as speciifed and directed. |
| 55 | M&L for preparation of newly plastered or unplastered surfaces of ceiling and apply three coat of white wash on prepared ceiling surface complete all as specified and directed. |
| 56 | M&L for preparation of old painted ceiling surfaces & applying one coat of white wash on ceiling surfaces complete all as specified and directed. |
| 57 | Taking down steel tubing and connections incl cleaning for refixing or removal form site for 20mm bore pipeall as specified and directed by Engr-in-charge. |
| 58 | Supplying and laying20 mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. ® |
| 59 | S&F 20mm bore tubes medium grade galvanized with all fitting and laid in trenches or fixed complete to walls or ceilings or laid in floors of any length all as specified and directed by Engr-in-charge. |
| 60 | M&L forWelded steel wire fabric supplied and fixed complete to wood or steel members weight not exc 4 kg/sqm complete all as sepecifed |
| 61 | Refixing old steel tubing and connections in new or old position (walls, ceiling, floors, etc) of 20 mm bore of pipe complete all as specified and directed. |
| 62 | S&F Rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) 1000 litre capacity, triple layer, hoisted and fixed in position all as specified in SSR Part-I, including dismantling of old u/s water storage tank complete all as specified and directed. |
| 63 | S&F ball valves for 20 mm bore dia of pipe high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe & fixed. (Minimum weight 210 gms) complete all as specified and directed. |
| 64 | S&F in repair, Brass chromium plated Wall Mixer 3-in-1 System with provision for both Hand Shower & Overhead Shower complete with 115 mm long bend pipe, connecting legs & wall flanges (without Hand & Over Head Shower) for 15 mm bore of pipe complete all as specified and directed. |
| 65 | S&F in repair, Chromium plated Angular Stop Cock with wall flange for 15 mm bore of pipe complete all as specified and directed. |
| 66 | S&F in repair, Chromium plated Two-way Bib Cock for 15 mm bore of pipe complete all as specified and directed. |
| 67 | S&F in repair, 15 mm dia of bore, fancy type, chromium plated stop valves, cast copper alloy, with long shank and cup (concealed type), screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed. |
| 68 | S&F in repair, 15 mm dia of bore, fancy type, chromium plated stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed. |
| 69 | S&F in repair, Health Faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube & ABS wall hook including making connections & fixed in position complete in all respect complete all as specified and directed. |
| 70 | S&F in repair, Vitreous china wash down water closet pan (pedestal pattern), white, with \"P\" or \"S\" trap including connecting to outgoing drain pipe & to flushing pipe excluding fixing bolts, flushing cistern and flush pipe complete all as specified and directed. |
| 71 | S&F in repair, plastic water closet seat cover, black/white, closed pattern with recessed bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed. |
| 72 | S&F in repair, 10 ltrs capacity PVC valveless, syphonic action type flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed. |
| 73 | S&F in repair, Vitreous china wash basin, white, flat back, size 550 x 400 mm excluding taps, waste, chain & plug & porcelain stopper but including bracket & including supply & fixing of 32 mm dia of bore, brass chromium plated waste coupling complete all as specified and directed. |
| 74 | S&F in repair, 15 mm dia of bore, fancy type pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered \"Hot\" or \"Cold\" with long screwed shanks and fly nuts, screwed for iron pipe & fixed complete all as specified and directed. |
| 75 | S&F in repair, Brass Chromium Plated, tubular towel rail, 20 mm dia, D type, 60 cm long between flanges etc complete all as specified and directed. |
| 76 | S&F in repair, Soap Dish Holder any type fixed to plug with chromoium plated brass screw complete all as specified and directed. |
| 77 | S&F in repair, corner glass shelf with brackets complete all as specified and directed. |
| 78 | S&F in repair, Sheet Glass Shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed. |
| 79 | S&F in repair, toilet paper holder with flat recessed type stainless steel complete all as specified & directed. |
| 80 | S&F in repair, Door Seal with aluminium beading and 50 mm wide rubber seal, fixed to Aluminium/Wooden doors complete all as specified and directed. |
| 81 | S&F in repair, Floor door stopper of aluminium alloy body and tongue, anodised, over all length of cover plate 140 mm, with hard drawn steel spring, fixed in door complete all as specified and directed. |
| 82 | S&F in repair, 600 mm x 450 mm bevelled edge looking mirror of selected quality glass, mounted on 6 mm thick AC building board or commercial plywood & fixed to wooden plugs with chromium plated brass screws & cup washers complete all as specified and directed. |
| 83 | S&F in repair, 125 mm size, Brass chromium plated shower rose with or without swivel joints, including fixing to steel pipe or union complete all as specified and directed. |
| 84 | S&F in repairs PVC connection 15mm size with PTMT nuts of length 600mm complete all as specified and directed. |
| 85 | S&F in repair, 32 mm bore, PVC waste pipe for Wash Basin/Kitchen Sink etc complete all as specified and directed. |
| 86 | S&F in repair, 32 mm dia of bore, Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed. |
| 87 | Taking down of eves gutter,rain water pipes of any size or pattern including all fittings etc complete all as specified and directed. |
| 88 | S&F 110 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors. Complete all as specified and directed. |
| 89 | S&F 75 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors. Complete all as specified and directed. |
| 90 | S&F PVC (SWR) bends ISI marked any radius of 110 mm borewithaccess door complete all as specified and directed. |
| 91 | S&FPVC (SWR) bends ISI marked any radius of 75 mm borewithaccess door complete all as specified and directed. |
| 92 | S&F PVC (SWR) floor trap 75 mm, setting and jointing with solvent cement complete all as specified and directed |
| 93 | S&F in repair PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed |
| 94 | S&F in repair 125mm/ 150mm dia mild steel chromium plated grating fixed on floor trap / nahani trap in Cement mortar 1:6 ,all as specified and directed by Engr-in-charge. |
| 95 | S&F in repair Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe & fixed in 20 mm bore dia of pipe. Complete all as specified and directed. |
| 96 | Dismantling wrought iron or mild steel work of any description not otherwise provided for. |
| 97 | M&L Water proofing treatment on roofsurface (Horizontal & Vertical surfaces) in following sequence through manufacturer / authorized applicator of the manufacturer including taking down of existing roof treatment,properly cleaning & drying the concrete surfaces complete all as specified and directed. |
| 98 | (i) M&L10 mm thick rendering on roof surfaces/concrete surface in CM 1:4 with WPC Compound complete. Note : WPC Paid seperitaly |
| 99 | (ii) Applying a coat of oxidised bitumen based solvent primer @ 0.3 Kg / Sqm |
| 100 | (iii)Applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 kg/ Sqm incl cleaning surfaces. |
| 101 | (iv) APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified 100 mm over laps shall be sealed by flame as per manufacturers instruction. |
| 102 | (v)applying a coat of blown grade hot bitumen 90/15 over the membrane @ 1.2 Kg /Sqm top of membrane surface shall then be finished applying with two coats solar reflective bituminious aluminium paint @ 0.10 Kg/Sqm complete |
| 103 | M&L for fillet of 75mm size using PCC 1:2:4 type B-1 (using 20 mm graded aggregate) at the junction of all horizontal and vertical surfaces complete all as specified and directed. |
| 104 | M&L forPCC 1:2:4 (Type B1 using 20 mm graded aggregate) levelling course,to match the undulations of roof complete all as specified and directed. |
| 105 | S&F mild steel flat iron as in bands, straps, supports or stays for rain water, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; will ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe -290 Gde E-165 complete all as specified and directed. |
| 106 | S&F factory made rubber moulded glossy finished Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors over 15 mm thick screed bed in CM 1:6 complete all as specified and directed. |
| 107 | Demolition of Cement Concrete (reinforced) of any description & in any position not otherwise specifically provided for complete all specified and directed. |
| 108 | M&L Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with & including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips. Complete all as specified and directed. |
| 109 | M&L Precast cement concrete type B1 1:2:4 (using 20mm graded crushed stone aggregate) asin landings, cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain facesand set in CM 1:6 |
| 110 | S&F in repair 15mm bore bib tap fancy type, chromium plated alloy, with a crutch or butterfly handle screwed down for iron pipe or for brass ferrule complete all as specified and directed. |
| 111 | Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, holders, pendants, regulators, sockets etc and making good disturbed surface by using cement mortar, white cement, putty etc and match with existing surfaces of walls, floors etc complete all as specified as directed. |
| 112 | Taking down carefully any type of old unserviceable submain wiring with PVC/steel conduit surface / concealed or wooden battensetc and making good the disturbed surfaces to match with the existing surface complete all as specified & directed by Engineer-in-Charge. |
| 113 | Taking down carefully any type of DBs including MCCBs and MCBs for keeping the old materials into safe custody or for taking credit(credit for above items should be made as per condition seaparately) and making good to the disturbed surface etc complete all as specified and directed. |
| 114 | M&L for point wiringfor One light point controlled by one switch 5/6 Amps complete with 1.5 Sqmm multistranded copper conductor single core PVC insulated unsheathed FR-LS cable 1100 volts grade (ISI marked) with proper colour coding drawn through and including non-metallic rigid PVC medium grade conduit not less that 20mm dia and conduit accessories (ISI marked) concealed in wall/fixed to roof, ceiling etc including provision of 1.5 Sqmm PVC insulated multistranded unsheathed copper conductor cable FR-LS (ISI marked) as earth continuity conductor connected to common earth dolly, including cutting chases of existing wall for conduits and sinking for boxes and making good to the disturbed surface of wall/floor and matching with existing specifications.Connections of cable with MCBs or bus bar shall be done through proper size copper/brass thimbles. Where concealing of conduit is not feasible ie on surface of roof etc, conduit shall be fixed on surface with necessary saddles at no extra cost complete all as specified and as directed. |
| 115 | All as per Item No 109.00 here-in-before but for one Ceiling fan/Exhaust fan Point controlled by one switch 5/6 Amps. |
| 116 | All as per Item No 109.00 here-in-beforebut for oneBell/buzzer Point controlled by one push button switch 5/6 Amps . |
| 117 | All as per Item No 109.00 here-in-before but for one socket point 5/6 Amp controlled by one switch on same board. |
| 118 | All as per Item No 109.00 here-in-before but for onesocket point 5/6 Amp controlled by one switch on Independent board. |
| 119 | Description same all as per item No. 109.00 here-in-before but with 1100 Volts grade copper stranded conductor FRLS cable of size 2.5 Sqmm main & with 2.5 Sqmm earth multi-strand copper conductor cable as earth wire for 3 pin switch socket outlet 5/15 Amp on Independent board complete all as specified & directed by Engineer-in-Charge. |
| 120 | Description same all as per item No. 109.00 here-in-before but with 1100 Volts grade copper stranded conductor FRLS cable of size 4 Sqmm main & with 4 Sqmm earth multi-strand copper conductor cable as earth wire for 3 pin switch socket outlet 5/15 Amp on Independent board complete all as specified & directed by Engineer-in-Charge. |
| 121 | Materialand labour for concealed sub-main wiring alongwith earth wire of size of 2 x 6.0 sq. mm + 1 x 6.0 sq. mm earth wire, ISI marked, FRLS, PVC insulated, multi stranded, copper conductor, single core cable drawn through and including PVC rigid conduit (medium grade) of size not less than 25 mm with all fittings and accessories ISI marked including cutting chases for conduits &making good to walls, floors etc complete, all as specified and as directed. NOTE: Two runs of 6 sqmm conductor for main and one run of 6 sqmm conductor as earth wire with proper colour coding including one run of PVC conduit shall be measured as one unit length. Connections of cables with MCBs or bus bar shall be done through appropriate size brass/ copper thimbles |
| 122 | S&F call bell, multi music type, suitable for AC 230 volt single pole complete all as specified & directed. |
| 123 | S &F Lamp holder, PVC/ polycarbonate type with back plate for angle holder all as per specified and directed. |
| 124 | S&F Ceiling rose surface type 60 x 30 mm three terminals of polycarbonate body complete all as specified & directed. |
| 125 | S&F modular switch6 Amps one module230 volts AC complete all as specified and as directed. |
| 126 | S&F modular switch16 Amps one module230 volts AC complete all as specified and as directed |
| 127 | S&F modular socket, 6A -2/3 pin combined 2 module,230 volts AC complete all as specified and as directed. |
| 128 | S&F modular socket, 6/16A -2/3 pin combined 2 module,230 volts AC complete all as specified and as directed . |
| 129 | S&F modular bell push , 6 Amps, 1 module complete all as specified and as directed. |
| 130 | S&F modular fan regulator, 2 Module 4 step upto 180 W heavy duty 230 volts complete all as specified and as directed. |
| 131 | S&F modular cover plate 2 module includingscrews and washers etc complete all as specified and as directed. |
| 132 | S&F modular cover plate 3 module includingscrews and washers etc complete all as specified and as directed. |
| 133 | S&F modular cover plate 4 module includingscrews and washers etc complete all as specified and as directed. |
| 134 | S&F modular cover plate 8 module includingscrews and washers etc complete all as specified and as directed. |
| 135 | S & F Metal flush box 2 module complete all as specified and directed. |
| 136 | All as per Item No 130.00 here-in-before but 3 module complete all as specified and directed |
| 137 | All as per Item No 130.00 but 4 module complete all as specified and directed |
| 138 | All as per Item No 130.00 but 8module complete all as specified and directed |
| 139 | S&Fsheet metal enclosure MCCB DB TPN 4 Way vertical type 250 A Copper Busbar for each phase Fully insulated busbar & shrouded Neutral bars with provision for DPX³ 160 MCCBas incomer and SP/TP MCB\"s as outgoing Reversible Door for IP 43 IK-09 DB\"s system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and directed. |
| 140 | Supply and Fixing Sheet metal enclosure for DBs when MCBs to be Used, 4 way, SP & N, double door type, 240 Volt (Note : MCBs will be Measured separately) including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and directed. |
| 141 | Supply and Fixing MCCB, four pole, 100 Amp, 415 Volt, of breaking capacity 16 KA complete all as specified and directed. |
| 142 | Supply and fixing 240V 10KA \"C\" curve miniature circuit breaker (MCB), SPN, 40 Amps current carrying capacity in the DB complete with connection, testing and commissioning, all as specified and directed. |
| 143 | Supply and fixing 240V 10KA \"C\" curve miniature circuit breaker (MCB), SP, 6-32 Amps current carrying capacity in the DB complete with connection, testing and commissioning, all as specified and directed. |
| 144 | Supply & Fixing Smart bright Batten Series, LED luminaire using LEDs 20 watt min 100 LM/watt, natural white(4000K)/ cool white (6500k), with diffuser which ensures uniform distribution and comfort batten series features latest LEDs and delivers consistent light outputwith wide voltage protection range, stable color start Extruded Aluminum housing, Energy efficient, flicker free start inbuilt driver unit suitable for wall and ceiling mounting using brackets (supplied along with The Luminaire has been tested as per standard specification IEC 60598-2-1 / IS: 10322(Parts/Secl), report has established conformity of the product(s) to the requirements of the Standard/Specification. |
| 145 | Supply and fixing LED bulk head luminaires,9 watts (600-900 lumens) lamp with fittings, connecting cable PVC insulated and PVC sheathed copper flxible cable of size 16/ 0.20 mm with necessary fixing arrangments complete all as directed. |
| 146 | S & F LED Mirror light fitting 2 ft tubelight, 10 watt aluminum housing and integrated electronic driver complete with fixing arrangements on wallall as specified and directed. |
| 147 | Supply & fixing LED Security Light Luminaire 35 wattwith 2500 or more lumen warm white/cool day ligh with, surge protection device upto 4KV, IP65 or more, IK07 or more, potted driver suitable for 180 to 270 V, 50 Hz, light engine driver base.pole adapter, powder coated pressure die cast aluminium with heat resistant toughened glass with lens type,GI pipe 40 mm dia medium Grade not less than with 1.2 m.long in any shape with 2 nos ofpole/wall fitting clamps made out of MS flat , nutsand boltsand painting with aluminium paint. complete all as specified and as directed. |
| 148 | S&F LED Bulb230V AC12 watt warm/cool day light 6500K as per the direction/requirement of sitecomplere all as specified and directed by Engineer-in -charge. |
| 149 | Taking down ceiling fan/exhaust fan sealing cable end, dismantling blades and removing fan and blades to store complete all as specified by Engr in charge |
| 150 | M & L for Hanging only ceiling fan/exhaust fan and connecting up including provision of flexible cable from ceiling rose or connector to fan Including hook and clamps with nut ,bolts, washers etc complete all as specified and directed |
| 151 | M & L for painting of ceillingfan/exhaust fan of any make/model and size complete with one coat of 1st grade quality of synthetic whiteenamelled paint by spraying including preparation of old paianted surface to remove all dust, oil mark etc and filling cavaties with filler materials, before painting, complete writing the MES numbers on ceiling fan with flack synthetic enamel paint of 1st grade quality by stenciling with uniform size of letters/of figures n.exc 20 mm in height letters/figures to be written in each fan complete all asspedified and directed. |
| 152 | Fixing electric meters upto 25 amps with complete fittings such asnut, bolt, check nut and washers including taking down old one with complete connections all as specified by Engr in charge |
| 153 | Fixing and connecting of geyser capacity 25 ltr with complete fittings such as cold and hot water connection pipes,suitable thread size nut bolts-02 Nos and accessories including taking down old one complete all as specified by Engr in charge |
| 154 | M & L for sheet metal enclosure fabricated out of 2.0 mm thick CRCA sheet, totally enclosed type, dust & vermin proof, with suitable sized supporting MS angles & suitable openings at top & bottom for entry of outgoing / incomming cables, fixed with nuts & bolts & front side openable with hinged shutter with suitable locking arrangement duly painted with 2 coats of powder coated paint over a coat of red oxide primer with minimum dimensions (50 x 50 x 25 cm ) flush to wall for incorporating 01 No SPN DB, 01 Nos electronic metersincluding danger notice board etc,complete all as specified and as directed. |
| 155 | M & L for Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4mm dia galvanised iron or steel wire |
| 156 | M &L for Earthing complete with GI earth plate electrode 600x600x6mm thick buried directly in ground (Earth pit not less than 2.25M deep below normal ground level) with top edge of the plate not less than 1.5m below normal GL. Connected to galvanized earth lead wire 4mm dia by means of nut, bolt, check nut and washersincluding necessary excavation and earth work in soft/loose soil, GI protection pipe light grade 15mm bore for protecting the GI wire mesh funnel alternate layer of charcoal dust, and saltPCC pit 1:3:6 type C1 using 20mm graded stone aggregate and 50mm thick RCC 1:2:4 type B1 using 20mm graded stone aggregate with angle iron CI frame 40X40X5mm , CI cover with provision of locking arrangementcomplete all as specified and shown in Electrical plate No.3 SSR part-1 and connected to the earth point and testing complete including taking out the old one complete all as specified and directed by Engr-in-Charge. including necessary excavation and earthwork in any type of strata and testing complete including fill up the earth pit with soil for best result and removal. Note :-(i) Earth protection pipe & earthing wire upto and including 7.5 m length is deemed included in unit rate quoted by the contractor (ii) If earth resistance of earthing is not found satisfactory it will be redone by the contractor without any extra cost to Govt.. |
| 157 | Taking up or down 25 mm bore steel tubing in trench/ wallwith connection including cleaning for removal all as specified anddirected. |
| 158 | M&L GI tubing 25 mm bore medium grade with all fittings laid in trenches/wall for bore of pipe of following sizes completed all as specified and directed. |
| 159 | Supply and fix Gun metal ,globe Gate Valves with iron wheel head of 20 mm dia bore complete with all accessories all as specified and directed by Engineer-in-charge. |
| 160 | M& L for cutting existing GI pipe alteration or addition of 40/50 mm dia bore for inerstion of reducer Teecomplete with all accessories all as specified and directed by Engineer-in-charge. |
| 161 | Excavation in trenches in soft/loose soil not exc. 1.5 metre wide and not exc. 1.5 metre in depth and getting out for taking up / layingunder ground electric cable complete with all accessories all as specified and directed by Engineer-in-charge. |
| 162 | Returning, filling in, including spreading levelling watering and well rammming in layers not exceeding 25 cms in depth complete with all accessories all as specified and directed by Engineer-in-charge. |
| 163 | Removing excavated materials n.exc 50m and depositing were directed at a level n.exc. 1.5m above the starting level |
| 164 | M&L for sand cushioning in cable trenches over & under the cable, with river washed coarse sand, as per standard practice with proper compaction complete all as specified and directed by Engr-in-Charge. (Punned thickness 18 cm shall be considered for payment as per para 19.75 of SSR Part-I) |
| 165 | M & L for Fly Ash bricks Sub-class \"B\" locally available laid flat in trenches over sand cushioning for cable protection complete all as speciffied and directed. |
| 166 | Supply and fixing 40 mm dia GI tubing medium grade ISI marked fixing to pole with suitable clamps / laid under floor/road for protection of cable including complete all as specified and directed. |
| 167 | Disconnecting & taking out defective under ground LT cable from trenches, pole, pipe,floor ,wall etc including bricks ,GI pipes and removing from work site of unserviceable material of any size complete as directed (Excavation/earth work shall be measured & paid separately under relevant item of this schedule) |
| 168 | Supply, Laying & testing and commissioning LT underground cable 1100 volts grade, 35 Sqmm 3.5 Core LTXLPE insulated and PVC sheathed heavy duty armoured with multi staranded aluminium conductor laid in pipes, trences/ducts, on poles etc of size complete all as specified and directed. |
| 169 | Material and labour for horizontal boring across the existing road without disturbing the road surface for inserting 40 mm bore GI pipe, complete all as specified and as directed. |
| 170 | Schedule of credit amount of Rs 115008.46 to be deducted during AOC. |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
