|
| 1 | Surface dressing n exc 15 cm deep in soft/loose soil complete all as specified and directed. |
| 2 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/dense soil complete all as specified and directed. |
| 3 | M & L for Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and directed. |
| 4 | M & L for Treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed. |
| 5 | M & L for Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed. |
| 6 | M & L for Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and directed. |
| 7 | M & L for Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed. |
| 8 | M & L forTreatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed. |
| 9 | M & L for Plain Cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and directed.. |
| 10 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in hard/dense soil complete all as specified and directed. |
| 11 | Removing excavated material exc. 1.50 km but n exc. 5km and depositing where directed outside Md land complete all as specified and directed. |
| 12 | Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for flat rough finished surface complete all as specified and directed. |
| 13 | M&L for RCC M-30 (Design mix) using 20mm graded crushed stone aggregate asin foundations, including rafts, footings, foundation beams, plinth beams, foundation for columns, etc complete all as specified and directed. |
| 14 | M & L for Formwork to sides of pillars, posts, struts, piers,columns and stanchions for flat fair finished surface complete all as specified and directed. |
| 15 | M&L for RCC M-30 (Design mix) using 20mm graded crushed stone aggregate asin columns,pillars etc complete all as specified and directed. |
| 16 | Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, for flat fair finished surface complete all as specified and directed. |
| 17 | M&L for RCC M-30 (Design mix) using 20mm graded crushed stone aggregate asinlintels beams and roof beams etc complete all as specified and directed. |
| 18 | Useand waste offormwork to flat surfaces of chullah hoods, chajjas, troughs and similar items including edges complete all as specified and directed by Engineer-in-Charge. |
| 19 | M&L for RCC M-30 (Design Mix) using 20mm graded stone aggregate as in chajjascomplete all as specified and directed. |
| 20 | Use and waste of form work to soffits of suspended slabs such as roof slabs, n. exc. 20cm thick (horizontal or sloping for fair finished concrete surface complete all as specified and directed. |
| 21 | M&L for RCC M-30 (Design mix) using 20mm graded crushed stone aggregate asinslabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and the likeetc complete all as specified and directed. |
| 22 | Use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide flat fair finished surface complete all as specified and directed. complete all as specified and directed. |
| 23 | S & F high strength corrosion resistant TMT steel bars,Grade Fe 500D, 10 mm dia., and over cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed. |
| 24 | S&F mildsteel TMT bars ,Grade Fe 500D, 5mm dia and over upto and including 10 mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 25 | M&L for Brick work with subclass ‘B’ old size fly ash bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and directed . |
| 26 | M&L for Brick work with subclass ‘B’ old size fly ash bricks, straight or curved on plan exc 6m mean radius in half brick thick walls in, built in cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge. |
| 27 | M & L for rendering 15 mm thick in two coats (10mm+5mm each) on other than fair faces of brick work or concrete surfaces in cement mortar 1:4,mixed with integral water proofing compoundwith weight of cement in top layer as per manufacturer\"s instructions and finished the surface even and fair without using extra cement complete all as specified and directed. (Note : WPC shall be measured and paid separately against respective item). |
| 28 | Supply only integral water proofing compound [ISI marked] of approved make. |
| 29 | M&L for10 mm thick rendering in CM 1:6 onfair face of brick workfinish the surface fair and even without using extra cement complete all as specified and directed by Engineer-in-Charge. |
| 30 | M & L for rendering 5 mm thick in Cement Mortar 1:3 on fair faces of concrete surface of ceiling surfaces finished even and smooth without using extra cement complete all as specified and as directed. |
| 31 | M & L for Powder coated aluminium sections of approved colour for doors, Windows, Ventilators, Partitions, with frames and shutters fully or partly glazed, sliding / openable, with extrudedaluminium sections not less than 1.5mm thick and powder coating not less than 60 micron thick including necessary jointing cleats, rubber beading, neoprene packing, aluminium snap beading, screws, powder coated aluminium fittings such as handles, aluminium butt hinges , aluminium tower bolts, stainless steel friction hinges, locking arrangementsetc.complete all as specified and as directed. Notes:[a]The size of aluminium extruded sections shall conform to Designation 63400 all shall be as specified in relevant IS code and as specified in MES Schedule Part - I. [b] Panel inserts such as Glass / Particle board / Gauze shall be measured and paid separately at supply only rates.[c] Weight of aluminium sections shall only be accounted for payment purpose. Weight of aluminium Handles, Butt Hinges & Tower Bolts shall not be accounted for payment purpose. [d] The unit rate quoted shall be deemed to include for cost of jointing cleats, glazing clips, rubber beading, neoprene packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as handles, aluminium butt hinges, aluminium tower bolts, stainless steel friction hinges, locking arrangementsetc. |
| 32 | Supply only 5.5mm thick sheet Glass ordinary quality in squares exceeding 0.5 Sq.m in each pane complete all as specified and as directed. |
| 33 | Supply only ofStainless steel wire cloth / mesh with average aperture not exceeding 1.40 mm and dia of wire 0.36 mm complete all as specified and as directed. |
| 34 | Supply only 5.0mm thickfigured glass, pinhead type in squares n exc 0.5 sq. m each pane complete all as specified and as directed. |
| 35 | S & F for Powder coated Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin-charge. |
| 36 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full Body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm 2 , modules of elasticity 900 N/mm 2 and resistance to spread of flame of Class A category with water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 37 | S & F factory made 35mm thick Flush shutters, solid core construction, with particle board core and plywood face panels, with 0.9mm thick decorative choice lamination on both sides complete all as specified and as directed. |
| 38 | S & F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening complete all as specified and directed. |
| 39 | S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified and directed. |
| 40 | S&F 125 mm long SS butt hinges, medium weight, cold rolled mild steel, complete all as specified and directed. |
| 41 | S&F 100 mm long SS butt hinges, medium weight, cold rolled mild steel, complete all as specified and directed. |
| 42 | S & F 150 mm long fancy type cromium plated brass handles, cast type, polished bright of sizecomplete all as specified and as directed. |
| 43 | S & F 150 mm size fancy type cromium plated brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts complete all as specified and as directed. |
| 44 | S & F for 300mm long fancy type cromium plated brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts complete all as specified and as directed. |
| 45 | S & F floor door stopper of size 150 mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified and as directed. |
| 46 | M&L for preparation of new platered surface of wall and applyingtwo coats of weather proof 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre, dart pick up resistant,silicon enhanced,UV resistant and PU enhanced propertyover a coat of alkali resistant primer including applying one or more coat of wall care putty to a smooth surface including making good any undulations on the surfacesincluding all necessary scaffolding,complete all as specified and directed.Note :-Painting work shall be carried out acoording to Smart Painting procedure mentioned in PS |
| 47 | M & L for preparing newly plastered surfaces of wall and applyingtwo coats of oil bound washable distemper over a coat ofprimer including applying one or more coat of wall care putty to get a smooth surface including making good any undulations on the surfacescomplete all as specified and as directed.Note :- (i) Painting work shall be carried out acoording to Smart Painting procedure mentioned in PS(ii) Sanding of surfaces shall be done by mechanical sander with 1500-2700 rpm with internal dust extraction system for clean environment certified by the Paint manufacturer) |
| 48 | All as per item no 47 here in before but on ceiling |
| 49 | M & L for hardcore of gauge n.exc 63 mm of broken stone or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed. |
| 50 | M & L for 75 mm thick,plain cement concrete1:4:8, typeD-2 (using 40mm graded stone aggregate) as in sub base complete all as specified and directed. |
| 51 | M&L for 25 mm thick PCC 1:2:4 type B-0 (using 12.50 mm graded stone aggregate) as in sub base of floor finished the surface even and fair complete all as specified and directed. |
| 52 | M & L for 75 mm thick,plain cement concrete1:3:6, type C-1 (using 20mm graded stone aggregate) as in plinth protection etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand 1:2 complete all as specified and directed. |
| 53 | M & L for non skid ceramic tiles, joint free, light shade coloured, premium quality of size exceeding 0.18 Sq.m and not exceeding 0.38 Sq.m, 7 to 8 mm thick [Square or Rectangular] as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tile including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:4 complete all as specified and as directed. |
| 54 | M & L for non skid ceramic tiles, joint free, light shade coloured, premium quality of size exceeding 0.18 Sq.m and not exceeding 0.38 Sq.m, 7 to 8 mm thick [Square or Rectangular] as as in vertical surfaces such as Skirting/dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tile over backing coat of 10mm thick in cement mortar 1:3 complete all as specified and as directed. |
| 55 | M & L for joint free glazed ceramic tiles, edge cut, coloured, premium quality, of size 300 mm X 450 mm, 7 to 8 mm thick as in vertical surfaces such as skirting, dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tile over backing coat of 10mm thick in cement mortar 1:3 complete all as specified and as directed. |
| 56 | M & L for granite stone slab (of any type) 18 to 20 mm thick (Table rubbed and polished to smooth mirror finish), machine cut, colour Mexican Red/Ruby Red/Z black/Paerl black etc design/pattern as directed including inlays, borders, margins in two or more colours/shades as in floors, trades of steps, cill cooking platform etc set and beddedover 15 mm thick screed bed in cement mortor 1:6and jointed with grey cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the Granite slabs& cutting, polishing complete all as specified and directed.(Note: Single stone slab shall be used for entire length/height of steps, jambs, pillars, window cills, cooking platform etc and joints shall match with the flooring complete) |
| 57 | Material & labour for 25 mm thick cement concrete (1:2:4) type B-0 using 12.5 mm gaded stone aggregate laid on RCC roof slab to make surface levelled for proper slope finish the surface even and fair complete all as specified and as directed. |
| 58 | M & L for 10 mm thick, screed bed as in roof in cement mortar 1:3finishing the surfaces even and smooth without using extra cement mixed with water proofing compound as per manufacturer\"s instructions complete all as specified and directed. (Note: WPC shall be measured and paid seperately) |
| 59 | Material and labour for preparation of horizontal or vertical surfaces for water proofing treatment on existing cleaned non accessible RCC roof with the following specification and manufacturings instruction complete all as specified and as directed:-(a) Preparing and cleaning of fully dry surfaces as per IS3067-1966(b) Applying bitumen primer(85/25 grade)conforming to IS:3384-1968 over the cleaned plaster surface @ 0.5 Ltr per sqm by the same membrane manufacturer of density at 25°C, 0.87 to 0.89 kg / Liter and viscosity 70-160 cps shall be applied on the prepared surface.(c) Applying a layer of APP based polymeric membrance 3.0mm thick (minimum) weight 3.6Kg per sqm (reinforced) with polyster Non woven fabric weighing not less than 160gms per sqm by torch application.The over laps shall be minimum 100mm on the transverse direction and 75 mm on longitudinal direction. (d) Applying one coat of aluminium paint @0.10 ltr per sqm over APP based polymeric membrane. |
| 60 | Supply, hoistedand fixingin position 500 Ltrs capacity rotational moulded polyethylene water storage tank, double layer construction, ISI mark (cylindrical vertical with closed top)including provision of 40mm/25mm dia spouts for connecting inlet, outlet, over flow and washout pipes and tank nipple complete all as specified and as directed. |
| 61 | S & F 25 mm bore,Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight - 455 gms) complete all as specified and directed. |
| 62 | S & F for CPVC ball valve 25 mm outer diameter & Plain CPVC SDR 11 fittings suitable for 25mm outer dia CPVC pipes complete all as specified and directed. |
| 63 | S & F 110mm bore PVC [SWR] pipes single socketed,pressure rating 6kg/sqcm, type-A grade , in any length with solvent cement/ rubber ring joints, fixed to walls with necessary brackets, clamps complete all as specified and as directed. |
| 64 | S & F 75mm bore PVC [SWR] pipes single socketed, pressure rating 6kg/sqcm, type-A grade, in any length with solvent cement/ rubber ring joints, fixed to walls with necessary brackets, clamps complete all as specified and as directed. |
| 65 | S & F 110mm bore PVC [SWR] pipes single socketed, pressure rating 6kg/sqcm, type-A grade, in any length with solvent cement/ rubber ring joints, laid in trenches or in floors complete all as specified and as directed. |
| 66 | S & F 75mm bore PVC [SWR] pipes single socketed, pressure rating 6kg/sqcm, type-A grade, in any length with solvent cement/ rubber ring joints, laid in trenches or in floors complete all as specified and as directed. |
| 67 | S & F 110 mm bore PVC [SWR] bends of any radius with access door including jointing with solvent cement complete all as specified and as directed. |
| 68 | S & F 110 mm bore PVC [SWR] bends of any radius including jointing with solvent cement complete all as specified and as directed. |
| 69 | S & F 75 mm bore PVC [SWR] Bends of any radius with access door including jointing with solvent cement complete all as specified and as directed. |
| 70 | S & F 75 mm bore PVC [SWR] Bends of any radius including jointing with solvent cement complete all as specified and as directed. |
| 71 | S & F 110 mm borePVC (SWR) junction single, (Single T) equal or unequal with access door including jointing with solvent cement complete all as specified and as directed. |
| 72 | S & F 75 mm borePVC (SWR) junction single, (Single T) equal or unequal with access door including jointing with solvent cement complete all as specified and as directed. |
| 73 | S & F 110 mm borePVC (SWR) junction double, (Double T) equal or unequal with access door including jointing with solvent cement complete all as specified and as directed. |
| 74 | S & F 75 mm borePVC (SWR) junction double, (Double T) equal or unequal with access door including jointing with solvent cement complete all as specified and as directed. |
| 75 | S & F 110mm bore PVC (SWR) branch piece, single (single Y) equal or unequal with access door including jointing with solvent cement complete all as specified and as directed. |
| 76 | S & F 75mm bore PVC (SWR) branch piece, singlee (singlee Y) equal or unequal with access door including jointing with solvent cement complete all as specified and as directed. |
| 77 | S & F 110 mm bore PVC [SWR] Vent Cowl including jointing with solvent cement complete all as specified and as directed. |
| 78 | S & F100mm bore outlet PVC [SWR] Floor trap/ Nahani trap with SS grating including jointing with solvent cement complete all as specified and as directed. |
| 79 | S & F75mm bore outlet PVC [SWR] Floor trap/ Nahani trap with SS grating including jointing with solvent cement complete all as specified and as directed. |
| 80 | S & F CPVC Pipes 20 mm outer diameter & Plain CPVC SDR 11 Fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing, complete all as specified and as directed. |
| 81 | S & F CPVC Pipes 25 mm outer diameter & Plain CPVC SDR 11 Fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing,complete all as specified and as directed. |
| 82 | S & F CPVC Pipes 32 mm outer diameter & Plain CPVC SDR 11 Fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing,complete all as specified and as directed. |
| 83 | S&F for Stainess steel kitchen sinks with drainage board made of stainless steel 1mm thick kitchen or laboratorywith plugs, washers and waste coupling; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed. |
| 84 | S & Fvitreous China wash down water closet pan (pedestal pattern) of size350x480x395 mm white, including connection to outgoing drain andflushing pipe, anti syphonic pipe, P or S trap with PVC water closet seat cover, black or white or coloured ,closed pattern with flat bottom andmild steel chromium plated hinging device complete but excluding flushing cistern & flush pipe including making good damaged/disturbed surfaces complete all as specified and directed. |
| 85 | S & F 10 litre capacity, PVC valve less syphonic action type, flushing cistern, low level, white,with inlet, ball valve, flush pipe, float and handle including brackets complete all as specified and directed. |
| 86 | S & F 15 mm bore, Hand Shower (Health Faucet) with 8mm Dia, 1.2 Meter Long Flexible Tube & Wall Hook with all accessories complete all as specified and directed. |
| 87 | S&F vitreous China wash basin, size 550 x 400mm, white, flat back, with 32 mm dia PVC waste pipe, CP waste coupling,& backets including cutting for and pinning in ends of brackets but excluding tap complete all as specified and directed. |
| 88 | S&F15mm bore pillar taps, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered HOT or COLD with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed. |
| 89 | S&F brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed. |
| 90 | S & F Towel Ring CPfixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) as specified and as directed by Engr-in-charge. |
| 91 | S & F fancy type long body chromium plated bib taps, cast copper alloywith capstan head, screwed down, screwed for 15 mm dia bore iron pipe complete all as specified and as directed. |
| 92 | S & F 15mm bore, two way bib cock with wall flange cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. |
| 93 | S & F stops valves, cast copper alloy, chromium plated fancy type with capstan head screwed down, high pressure, screwed both ends for 15 mm bore iron pipe or for unions complete all as specified and as directed. |
| 94 | S & F 15 mm bore, angular stop valve, cast copper alloy, chromium plated, fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. |
| 95 | S & F 600mm x 900mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with 6 Nos of 10mm dia capastan head chromium plated brass screws and cup washers complete all ass pecified and directed. |
| 96 | S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed. |
| 97 | S & F Vitreous China urinal, half stall type (Back or corner wall type) of size 710x480x300 mm, white (minimum) with grating and SS bottle trap(excluding flushing cistern, flush pipe & waste pipe) including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cementincluding brass stainless steel speader 15 mm bore complete complete as specified and directed. |
| 98 | S & F 15mm bore, PVC connection pipe 600mm long with PTMT nuts at both ends complete all as specified and directed. |
| 99 | S & F 32mm dia flexible PVC waste pipe, 900mm long for wash basin/sink/urinal etc complete all as specified and directed. |
| 100 | M & L for sand filling under floors or in foundations incl watering and consolidation complete all as specified and directed. |
| 101 | M & L for Machine pressed precast conctete coloured interlocking paver blockwith glossy finish ,any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment complete all as specified and directed. |
| 102 | M & L for plain cement concrete (1:2:4), type B-0 (using 12.5mm graded stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, including necessary foRmwork complete all as specified and as directed. |
| 103 | M & L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4and finished the surfaces even and smooth without using extra cement complete all as specified and directed. |
| 104 | M & L for precast reinforced cement concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in cover slab (For manhole etc), chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain facesand set in cement mortar 1:4 including necessary form, moulds, etc complete all as specified and directed by the Engr-in-Charge. (Note : Reinforcement shall be measuredand paid separately) |
| 105 | S&L reinforced concrete pipes, class NP2, 200mm bore, laid and jointed with collars including necessary fittings complete all as specified and as directed. |
| 106 | M & L for Plain cement concrete 1:3:6, type C-2 (using 40 mm graded stone aggragate) as in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 200 mm bore SGSW/RCC drain pipes complete all as specified and directed |
| 107 | M & L for Plain cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) as in surface channel, drains etc complete all as specified and directed. |
| 108 | M&L for Pre-cast cement concrete block masonry with solidblocks made out of PCC 1:3:6 type C1 (using 20 mm graded stone aggregate) ,Grade \"C\" masonry with compressive strength of 5N/sqmm, exc. 10 cm in width and setting in cemet mortar 1:6 complete complete all as specified and directed. |
| 109 | Extra for forming fair finished to concrete surface of drain 30cm inner girth in cement including forms, mould, mitred/stopped etc complete all as specified and as directed. |
| 110 | M & L for conceledPoint wiring with two runs of single core 1.5 Sq.mm. (Nominal area) PVC insulated unsheathed multistranded copper conductor cable FRLSH (ISI marked) drawn through and including non metallic PVC conduit 20 mm bore (Minimum) medium grade (ISI marked) concealed type includingmetal GI boxes of suitable module including modular white cover plate of suitable module for fixing modular type switches, sockets, regulators etc. including provision of multistranded 1.5 Sq.mm copper conductorcable FRLSH [ISI marked] as earth wire connected to common earth dolly and earth in distribution board complete all as specified and as directed,for one light/exhaust fan/fan point/call bellcontrolled by one way switch.(Note.: (i) The rate quoted is deemed to include making good the disturbed sufaces and to match the adjoining surface. (ii) The quoted rate is deemed to include cutting chases for concealed wiring including making good the same as per the existing one) |
| 111 | All as per item No. 110 above but for One 3/5 pin socket outlet 6 amps on independent board complete ditto |
| 112 | All as per item No. 110 here in before but for one 15 Amps power point on the independent board with two runs of PVC insulated and unsheathed copper conductor cable of size 2.5 Sqmm multistrandedFRLSH (ISI marked) and 2.5 Sqmm PVC insulated unsheathed solid copper conductor cableFRLSH (ISI marked) as earth lead complete ditto |
| 113 | All as per item No.110 here in before but for one 15 Amps power point on the independent board with two runs of PVC insulated and unsheathed copper conductor cable of size 4.00 Sqmm multistrandedFRLSH (ISI marked) and4.00 Sqmm PVC insulated unsheathed solid copper conductor cableFRLSH (ISI marked) as earth lead complete ditto |
| 114 | S & F switch modular single pole one way 6 amp 240 volts,1 Module complete all as specified and as directed. |
| 115 | S & F Modular socket outlet6A, 2/3 pin combined, 2 module, AC 230V, 50HZ complete all as specified and as directed. |
| 116 | S & F switch modular single pole one way 16 amp 240 volts,1 Module complete all as specified and as directed. |
| 117 | S & F Modular socket outlet6A/16A, 2/3 pin combined, 2 module, AC 230V, 50HZ complete all as specified and as directed. |
| 118 | S&F ceiling rose, 65 X 50mm two to three teRminals, PVC/polycarbonate, insolated body complete all as specified and directed. |
| 119 | S & F steped type modular fan regulator ,100/120 W 2 module complete all as specified and as directed. |
| 120 | S&F Socket Residual Current Device (SRCD) With Steel Enclosure two pin and earth plug including 20 Amps MCB SP complete all as specified and as directed |
| 121 | S & F Telephonic jack deluxe with shutter single line with metal box complete all as specified and as directed. |
| 122 | S&F computer /LAN Jack Cat 6 with shutterwith metal box completeall as specified and directed.. |
| 123 | S & F powder coated sheet steel Distribution Board, TPN 4 Way, vertical , 415V, Double door with IP 43protection, IK 09 complete all as specified and as directed. |
| 124 | Supply, fixing, commissioning and testing MCB TP 50 to 63 Amps, 415 Volts,10KA, C curve complete all as specified and as directed |
| 125 | Supply, fixing, commissioning and testingMCB SP 6-32A Amps, 240 Volts,10KA, C Curve complete all as specified and as directed |
| 126 | S & F LED tube light fittings ultra-slim economical LED Battens in Extruded PC housing and Square shaped diffuser, 1x20 Watt,220 V,AC and 2000 Lumens of cool white with all accessories, internally prewired and connecting up with twin core twisted copper conductor cable of suitable size including tube lamp complete all as specifiedand directed. |
| 127 | Supply and fixingLED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. |
| 128 | M & L for Sub main wiring with 2 runs of Single core 2.5 sqmm [ for Phase & Neutral ]PVC insulated multi stranded FRLSH (ISI marked) copper cable drawn through and including surface PVC conduit of suitable size with all conduit accesories and fittings along with 1 run of single core 2.5 sqmm PVC insulated multi stranded FRLSH (ISI marked) copper cableas earth continuity conductorcomplete all as specified and as directed.(Note :- Two runs of 2.5 sqmm and one runs of 2.5 sqmm cable as earth wire and one run of conduitshall be measured as one length) |
| 129 | M & L for Sub main wiring with 2 runs of Single core 4 sqmm [ for Phase & Neutral ]PVC insulated multi stranded FRLSH (ISI marked) copper cable drawn through and including surface PVC conduit of suitable size with all conduit accesories and fittings along with 1 run of single core 4 sqmm PVC insulated multi stranded FRLSH (ISI marked) copper cableas earth continuity conductorcomplete all as specified and as directed.(Note :- Two runs of 4 sqmm and one runs of 4 sqmm cable as earth wire and one run of conduitshall be measured as one length) |
| 130 | Supply, fix, installation and commissioning BLDC ceiling fan of less noise, silent operation, light colour, conforming to IS-374-2019, 1200 mm sweep, 230 Volts, BEE 5 Star rating alongwith electronic type regulatorincluding all accessories such as down rod etc and connecting up with 1.5 Sqmm, PVC insulated, multistranded copper conductor cables from ceiling rose to fan complete all as specified and directed. (Note: Ceiling fan should have minimum 2 years manufacturer\"s warranty)Make : USHA/Havell\"s/Bajaj/CG |
| 131 | S&F Rigid non-metalic PVC conduit (20mmdia) exclusive of boxes (junction/ treminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hook etc. complete all as specified and directed. |
