|
| 1 | Demolition cement concrete (unreinforced) in ground floor and pavings not exceeding 15cm thickness below or above ground level with and including removing rubbish material from building and thrown in low lying empty areacompete all as specified and as directed by Engineer-in-charge. |
| 2 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) with and including removing rubbish material from building and thrown in low lying empty areacompete all as specified and as directed by Engineer-in-charge. |
| 3 | Material & Labourfor 25 mm thick PCC in Cement Mortar1:2:4 Type B-0 (using 12.5 mm graded stone aggregate) as in sub base of floorcomplete all as specified and directed by Engineer-in-Charge. |
| 4 | Material & Labour for GlazedCeramic tiles dark shade ( shade as approved by Engineer-in-charge ) ,10mm thick, in Square / Rectangular ,polished, area of each tileexceeding 0.36 Sqm but not exceeding 0.42 Sqm,laid as in floors set and jointed in neat cement slurry @ 3.00Kg per Sqm and pointed in white or coloured cement to match theshade of tiles , laidover with and including15mm thickscreed bed in cement mortar 1:4complete all as specified and directed by Engineer-in-Charge. |
| 5 | Material & Labour for Glazed Coloured Ceramic tilesdark shade ( shade as approved by Engineer-in-charge ) , 10mm thick , granite /Marble/ Wood trexture , area of each tilenot exceeding 0.36 Sqm ,as in vertical surfaces, set and jointed in neat cement slurry @ 3.00Kg per Sqm and pointed in white or coloured cement to match the colour / shade of tiles , laidover with and including10mm thick renderingin cement mortar 1:4complete all as specified and directed by Engineer-in-Charge. |
| 6 | Material & Labour for Glazed ColouredCeramic tiles ( colour as approved by Engineer-in-charge ) , size 450mm x 350mm x 7mm thick,as in vertical surfaces, set and jointed in neat cement slurry @ 3.00Kg per Sqm and pointed in white or coloured cement to match the colour of tiles , laidover with and including10mm thick renderingin cement mortar 1:4complete all as specified and directed by Engineer-in-Charge. |
| 7 | Material & Labour for15mm to 20mm thick granite slab (any type)in one piece machine cut (as approved by Engineer-in-charge) for counter sunk wash basin, plateform /cooking plateform , steps, jambs,pillars, window cills, , shelves, urinal partitionand like bedded and jointed with grey cement slurry @ 3.00Kg per Sqm and pointed with white cement with admixture of pigment to match the shade of granite stone with andincluding grinding and polishing , laid over with and including 15mm thick Rendering/ screed bedin Cement Mortar1:4complete all as specified and directed by Engineer-in-Charge. |
| 8 | Material & Labour for Machine cut kota slab20mm - 25 mm thick ( Kota stone as approved by Engineer-in-charge) as in flooring , laid and jointed with grey cement slurry @ 3.00 Kg per Sqm mixed with pigment to match the shade of the slab including rubbing and polishing, laid over with and including 15 mm thick screed bed in Cement Mortar 1:4complete all as specified and directed by Engineer-in-Charge. |
| 9 | Material & Labour for Machine cut kota slab20mm - 25 mm thick in one piece ( Kota stone as approved by Engineer-in-charge) as in vertical surfaces such as skirting, dado , pillar, risers of steps , etc. laid and jointed with grey cement slurry @ 3.00 Kg per Sqm mixed with pigment to match the shade of the slab including rubbing and polishing, laid over with and including 10 mm thick renderingin Cement Mortar 1:4complete all as specified and directed by Engineer-in-Charge. |
| 10 | Rounding to edges of stone slab on edge such as steps cooking platform and other similar situationscomplete all as specified and directed by Engineer-in-Charge. |
| 11 | Material and labour for 75 mm thick PCC (1:3:6) Type C-2 using 40mm graded stone aggregate as in flooring, hard standing, plinth protection / path etc. finished even and smooth without using extra cementcomplete all as specified and as directed by Engineer-in-Charge. |
| 12 | Taking down cement or cement lime plaster from brick wallor concrete surfaces etc including racking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge |
| 13 | Material and labour for Rendering 10mm thickinCement Mortar1:6 , on fair faces of brick work or concretesurfaces ,finish even & smooth withoutusing extra cementcomplete all as specified and directed by Engineer-in-Charge. |
| 14 | Material and labour for Rendering 15mm thickinCement Mortar1:4 , on fair faces of brick work or concretesurfaces ,finish even & smooth withoutusing extra cementcomplete all as specified and directed by Engineer-in-Charge. |
| 15 | Material and labour forpreparation of new plastered surface of walls with and includingapplying two coats of Oil EmulsionDistemperover with and includingone coat of appropriate primerover with and including 3.00mm thick wall care putty(as approved by Engineer-in-chargefor smooth & even surface) complete all as specified and directed by Engineer-in-Charge. |
| 16 | Material and labour forpreparation of old surface of walls (with using by broomingdown or steel wire burshing, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots ) ,with and including 3.00mm thick wall care puty(as approved by Engineer-in-chargefor smooth & even surface)with and includingapplying two coats of Oil EmulsionDistemper complete all as specified and directed by Engineer-in-Charge. |
| 17 | Material and labour forpreparation of new surface of walls, with and includingtwo coats of cement base paint ,over with and including one coat or alkalic resistance primer complete all as specified and directed by Engineer-in-Charge. |
| 18 | Material and labour forpreparation of oldsurface of walls, with and includingtwo coats of cement base paintcomplete all as specified and directed by Engineer-in-Charge. |
| 19 | Taking down chowkhats or frames with shutters of PVC door , wooden door shutter, wooden window shutter , Mild steel window and Mild steelventilators(without taking off shutters from the frames)areanot exceeding 1.50 sqm eachcomplete all as specified and asdirected by Engineer-in- charge. |
| 20 | Taking down chowkhats or frames with shuttersof PVC door ,wooden door shutter, wooden window shutter , Mild steel window and Mild steelventilators(without taking off shutters from the frames) areaexceeding 1.50 sqm but not exceeding 4.00 Sqm each complete all as specified and asdirected by Engineer-in- charge. |
| 21 | Material & Labour2ndclass hardwood, plain solid straight chowkhats and frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified and directed by Engineer-in-Charge. |
| 22 | Supply & FixingSolid PVC door frame of size 50mm x 47mm made out of 5 mm single side prelam PVC sheet reinforced with MS square tube manufactured as per SSR Part-I specifications and drawingscomplete all as specified and directed by Engineer-in-Charge.Note:- 1.The quoted rate deemed to include the cost of making good the disturbed surface with cement plaster 1:6 and matching the colour of new plaster with existing surface. Nothing extra shall be paid on this account. |
| 23 | Supply & FixingFactory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm widthstuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & asgap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.complete all as specified and directed by Engineer-in-Charge. |
| 24 | Supply and FixingFactory made 35mm thickframed, panelled shutter (two panel) with lock railmade of 2nd class Hard wood and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed by Engineer-in-Charge. Note: Butt Hinges, Tower bolts, Handles , sliding door boltsand painting shall be measured and paid seperately under appropriate items of schedule \"A\" BoQ. |
| 25 | Supply and Fixing 35mm thick, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars), using 2nd class hard wood (as approved by Engineer-in-charge) edges of frming plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc , sizes of members of shutters as specified in SSR Part-I, Section8, Clause 8.24 (a), supplied and fitted to chowkhats complete all as specified and as directed by Engineer-in-Charge. Note:- (i)Wire gauze / glass shall be measured and paid separately under appropriate items of Schedule \"A\" BoQ.(ii) Butt Hinges, Tower bolts, Handles , sliding door bolts, ordinary rat tail pattern springs and painting shall be measured and paid seperately under appropriate items of schedule \"A\" BoQ.(iii) The sutters shall be brought at site without primer and same shall be applying at site as per direction of Engineer-in-charge. (iv)Primer shall be measured paid separately under appropriate itemof BOQ. |
| 26 | Supply and Fixingfor30 mm thick 2nd class hard woodglazed and skeleton windows/ventilators shutters open rebated and prepared to receive glass, gauge etc , divide into square with plain chamfered or rounded, mitered and rebated sash bars any numbers , provided with stiles and rails as specified in SSR part I section 8 clause 8.24 (b) complete all as specified and directed by Engineer-in-Charge. Note:- (i)Wire gauze / glass shall be measured and paid separately under appropriate items of Schedule \"A\" BoQ.(ii) Butt Hinges, Tower bolts, Handles , sliding door bolts, ordinary rat tail pattern springs and painting shall be measured and paid seperately under appropriate items of schedule \"A\" BoQ.(iii) The sutters shall be brought at site without primer and same shall be applying at site as per direction of Engineer-in-charge.(iv)Primer shall be measured paid separately under appropriate itemof BOQ. |
| 27 | Supply and Fixing 200mm longh aluminium anodised barrel tower bolts ofextruded sectioncomplete all as specified and directed by Engineer-in-Charge. |
| 28 | Supply and Fixing aluminium alloy, anodised, sliding door bolt of length 300 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts ofsections or cast-aluminium extruded alloy and fixedcomplete all as specified and directed by Engineer-in-Charge. |
| 29 | Supply and Fixingbutt hingessize of 100mm , medium weight cold rolled mild steel complete all as specified and directed by Engineer-in-Charge. |
| 30 | Supply and FixingHandle 150mm, Extruded aluminium alloyhandles, fabricated type, anodisedcomplete all as specified and directed by Engineer-in-Charge. |
| 31 | Supply and FixingHandle 100mm, Extruded aluminium alloyhandles, fabricated type, anodisedcomplete all as specified and directed by Engineer-in-Charge. |
| 32 | Supply and FixingFloor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, with overall length of cover plate 150mmfixed in floor complete all as specified and directed by Engineer-in-Charge. |
| 33 | Supply and Fixingmild steel 300mm size ordinary rat tail pattern springs includingroller and roller plate complete all as specified and directed by Engineer-in-Charge. |
| 34 | Hacking out old or broken glass (any thicknesssize quility or description) from steel frames or stone concrete or brick surrounds glazed with putty or fixed with beadscomplete all as specified and directed by Engineer-in-Charge. |
| 35 | Supply and Fixing4mm thick sheet glass of ordinary quality and glazing with oil putty in square , not exceeding0.50 Sqm each in panecomplete all as specified and directed by Engineer-in-Charge. |
| 36 | Supply and FixingGalvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed by Engineer-in-Charge. |
| 37 | Taking up or down steel tubing 15mm bore and connectioncomplete all as specified and directed by Engineer-in-Charge.Note: ifExcavationrequired , Excavation and earth work shall be measured and paid seperately under appropriate items of schedule \"A\" BoQ. |
| 38 | Supply & Fixing15mm bore GI tubing medium grade with all newfittingslaid in trenchescomplete all as specified and directed by Engineer-in-Charge. Note: Excavation and earth work shall be measured and paid seperately under appropriate items of schedule \"A\" BoQ. |
| 39 | Supply & Fixing15mm bore GI tubing medium grade with all newfittings to walls and ceilings or laid in floors complete all as specified and directed by Engineer-in-Charge. |
| 40 | Fixing only 15mm bore GI tubing medium gradeafter thoroughly cleaning ofpipe retrived from serial item no.37.00 here-in- before with all newfittingslaid in trenchescomplete all as specified and directed by Engineer-in-Charge. Notes: 1.Excavation and earth work shall be measured and paid seperately under appropriate items of schedule \"A\" BoQ.2. The rate of cleaning of old servicable pipe is included in this item and nothing shall be paid extra on this account. |
| 41 | Fixing only 15mm bore GI tubing medium gradeafter throughlycleaning of pipe retrived from serial item no.37.00 here-in- before with all newfittingsfixed to walls and ceilings or laid in floorscomplete all as specified and directed by Engineer-in-Charge. Note:The rate of cleaning of old servicable pipe is included in this item and nothing shall be paid extra on this account. |
| 42 | Supply and fixing in replacementgrating doom 125mm dia with waste hole made of PTMT , weight not less than 40mm eachcomplete all as specified and directed by Engineer-in-Charge. |
| 43 | Supply and fixing in replacement 600mm x 450mm size bevelled edge mirror selected quality 5mm thick glass mounted on 6mm thick commercial ply and fixed to wooden plugs with chromium plated brass screws and cup washers, including aluminium frame / beading alround made of aluminium channel, complete all as specified and directed by Engineer-in-Charge. |
| 44 | Supply and fixingin replacement 15 mm borebrass Chromium Plated mixer for mixing hot and cold water , screwed down high pressure with long screwed shanks and fly nuts screwed for iron pipescomplete all as specified and directed by Engineer-in-Charge. |
| 45 | Material and Labour forpreparing wood or wood based surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by Engineer-in-charge. |
| 46 | Material and Labour forPreparation of oldplastered or unplastered surfaces of ceiling (with using by broomingdown or steel wire burshing, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots ) and with and includingapplying two coat of white washcomplete all as specified and directed by Engineer-in-Charge. |
| 47 | Dismantling of plain or corrugated steel sheeting any gauge, thickness including roof covering etccomplete all as specified and directed by Engineer-in-Charge. |
| 48 | Supply & FixingPre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specifiedcomplete all as specified and directed by Engineer-in-Charge. |
| 49 | Supply & FixingPre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed by Engineer-in-Charge. |
| 50 | Material & Labourin replacement weather boarding in 2nd class hardwood ,clean swan , plain , 20 mm thick or feather edges , 15 mm to 20 mm thick and fixed with 30 mm laps jointscomplete all as specified and directed by Engineer-in-Charge. |
| 51 | Demolition of wall and ceiling boards (fiber, pulp, insulation, etc) or insulation boards/slabs including cover fillets etccomplete all as specified and directed by Engineer-in-Charge. |
| 52 | Supply & Fixinganodised aluminium snap grid of size 605mmx 605 mm frame work for false ceilingcomplete all as specified and directed by Engineer-in-Charge. |
| 53 | Supply & Fixing10mm thick PVC insulation panels with EPS stuck to 1 mm thick plain PVC sheet suitably placed in false ceiling anodised aluminium snap gridcomplete all as specified and directed by Engineer-in-Charge. Note:The measurement and payment of grid made of aluminum shall be considered under serial item No.52.00 here-in- before. Nothing shall be extra paid in this item. |
| 54 | Supply and Fixing in replacement Stainless steel sink with draining board, made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers waste pipe, cast iron cantilever brackets, connecting union overall size 915mmx460mm with bowl size 410mm x 330mm x 160mmcomplete all as specified and directed by Engineer-in-Charge. |
| 55 | Taking down carefully aluminum / copper point wiring on Teak WoodBatten / in conduit / with conduit (light /Fan / socket or power) complete with andincluding taking down fittings such as switches, ceiling roses, pendants, Regulators, sockets, light fittings etc complete all as specified and directed by Engineer-in-Charge. Notes:(i) The weight of aluminium scrap, copper scrap and scrap ironfor schedule of credit shall be ascertain by BOO as ordered by GE.The copy of BOO duly countersinged by GE shall be enclosed with final Bill.(ii) The rate of cutting chases (as required) and making good surfaces to match with adjoining surfaceshall be measured and paid seperately under serialitem nos.56.00 to 60.00 of BoQ. |
| 56 | Material and labour for concealed Point wiring using approved colour coding as per IS (Red, Black and Green for single phase circuits), in newPVC conduit complete with and including1.5 Sqmm twosingle core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable 1100 volt grade ISI Marked , drawn through withand including new PVC rigid conduit 20mm dia( heavy duty )ISI marked with valid CML No.(IS-9537-1983 for conduits and IS:3419:1976 for conduit accessories) with all new fittings and all accessories i.e pipe bend pipe hook, elbow,junction box, pressed steel powder coated sunken box of suitable size (min 60mm deep, suitable length and 1.2mm thick )and flushfixed with cement mortar 1:4, 3mm thick bakelite plastic laminated sheet for mounting with frame and top cover forswitches 5Amp/6Amp , socket outlet 5Amp/6Amp and fan regulator, for light / fan point controlled by one way switch 5Amp / 6Amp, top cover fixed with brass screws & cup washers, with andincluding one single core 1.5 Sqmm FRLSH PVC insulated multi strand copper conductor cable1100 volt grade (ISI marked ) (as in green colour) as continues earth wire connected to earth dolly etc.with and including cutting chases (as required) and making good surfaces to match with adjoining surface complete all as specified and as directed by Engineer-in- charge .Notes for serial item nos. 56.00 to 60.00 : (i) switches one way 5 /6 Amp,socket out lets 5 /6 Amp, two way switches5 /6 Amp and Bell push switch shall be measured and paid seperately under respective items of Schedule\"A\" BoQ.(ii) The rate of cutting chases (as required) and making good surfaces to match with adjoining surface is included in this item and nothing shall be paid extra on this account. (iii) On RCC roof / ceiling PVC conduit shall be provided on surface with proper fixing clipsas directed by Engineer-in- Charge.The rate of this element is included in this item and nothing shall be paid extra on this account. |
| 57 | All as per serialitem No 56.00 of BoQhere-in-beforebut for socket outlet 5 pin 5Amp /6 Amp on same board, complete all as specified and directed by Engineer-in-charge. |
| 58 | All as per serialitem No 56.00 of BoQ here-in-before but for socket outlet 5 pin 5Amp / 6 Amp on independent board complete all as specified and directed by Engineer-in-charge. |
| 59 | All as per item No 56.00 of BoQ here-in-beforebut for one light point controlled by two - twoway switchescomplete all as specified and directed by Engineer-in-Charge. |
| 60 | All as per srl item No56.00 of BoQ here-in-beforebut 2.5 Sqmm twosingle core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable 1100 volt grade ISI Marked with andincludingone single core2.50 Sqmm FRLSH PVC insulated multi strand copper conductor cable 1100 volt grade(ISI marked ) as continuesearth wire connected to earth dolly etc for 3 pin socket outlet 15 Amps withcomplete all as specified and directed by Engineer-in-Charge. |
| 61 | Supply and fixing switch piano flush type 5 Amp single pole one way ISI markedcomplete all as specified and directed by Engineer-in-Charge. |
| 62 | Supply and fixing switch piano flush type 15 Amp single pole one wayISI marked complete all as specified and directed by Engineer-in-Charge. |
| 63 | Supply and fixing switch piano 5 Amp flush type single pole two way ISI marked complete all as specified and directed by Engineer-in-Charge. |
| 64 | Supply and fixing socket outlet 5 pin 5 Amps flush type multi purposeISI marked complete all as specified and directed by Engineer-in-Charge. |
| 65 | Supply and fixing socket outlet multipurpose 2 in one, 6 pin 15 Amps flush typeISI markedcomplete all as specified and directed by Engineer-in-Charge. |
| 66 | Supply and fixing Lamp holder ISI marked , PVC/Polycarbonate type with cord grip cap suitable for pendant fittingscomplete all as specified and directed by Engineer-in-Charge. |
| 67 | Supply and fixingin replacement LED lights fitting 1 x 20W, 220V, AC decorative box type with driver, holder including LED tube light 20 wattcomplete all as per manufacturer\"s instruction with andincluding electric connectionwith using flexible copper wire twin core upto ceiling roseto light fittingcomplete all as specified and directed by Engineer-in-Charge. Notes:(a) Contractor has to furnish a replacement warranty of 02 years forLED Light fittings complete includingfrom the certifiy date of completion of CA. The product will be replaced free of cost in the following case :-(i) Manufacturing defects.(ii) Failure due to mechanical and electrical impact.(iii) Drop in lumen (or lux at 1 m) below 90% of clamied values of lumen(or lux at 1 m) of the LED /Luminaries.(b) All LED lightmust meet the provision laid down in IS - 16101, 16102 Part -I/II,16103 Part -I, 16104,16105,16106, 16108/2012 and 15885 Part -II / Section 13.(c) Scope of work shall includeLED Light fittings walls/ceiling which includes needfulT & P andrequired accessories etcif any, complete including making connection, testing etc complete. No extra payment is admissible on these account. |
| 68 | Supply and fixingBatten fitting square profile type LED mirror light fiting 9/10 watt, 6000K, polycarbonate body andall other accessories fitting arrangements all other accessories fitting arrangements complete all as per manufacturer\"s instructionswith andincluding electric connection connecting with using flexible copper wire twin core upto ceiling rose/connector complete all as specified and as directed by Engineer-in-Charge. Notes:(a) Contractor has to furnish a replacement warranty of 02 years forLED Light fittings complete includingfrom the certifiy date of completion of CA. The product will be replaced free of cost in the following case :-(i) Manufacturing defects.(ii) Failure due to mechanical and electrical impact.(iii) Drop in lumen (or lux at 1 m) below 90% of clamied values of lumen(or lux at 1 m) of the LED /Luminaries.(b) All LED lightmust meet the provision laid down in IS - 16101, 16102 Part -I/II,16103 Part -I, 16104,16105,16106, 16108/2012 and 15885 Part -II / Section 13.(c) Scope of work shall includeLED Light fittings walls/ceiling which includes needfulT & P andrequired accessories etcif any, complete including making connection, testing etc complete. No extra payment is admissible on these account. |
| 69 | Supply and fixing ceiling rose surface bakelite 65mm x 50mmthree terminals ISI Markedcomplete all as specified and directed by Engineer-in-Charge. |
| 70 | Supply and Fixingfan regulator electronic step typeISI Markedand making connectioncomplete all as specified and directed by Engineer-in-Charge. |
| 71 | Supply and fixing in replacementsheet metal enclousers made out of CRCA mild steel sheet , IP-43 protection, flush mounted with metaldoor, powder coated DB SPN 8 way 230 V AC with 200 Amp rated copper bus bar, Double Door,08 modules, dust and vermin proof suitable for incorporation of MCBs/ MCCBs/ Isolators etc.conforming to IS/IEC-61439-2:2011, BS-5484 complete all as specified and directed by Engineer-in-charge. Notes: (i)MCBs / MCCBs/ Isolators shall be measured and paid seperately under appropriate items.(ii) The rate of200 Ampscopper bus bar is included in this item and nothing shall be paid extra on this account. |
| 72 | Supply and fixingin replacement sheet metal enclousers made out of CRCA mild steel sheet , IP-43 protection, flush mounted with metaldoor, powder coatedTPN, 4 Way 415 V (8+12 modules), double door, earth bar, copper bus bar 200 Amp and neutral link, protection class IP-43 suitable for mounting MCBs/ MCCBs/ Isolators, conforming to IS/IEC-61439-2:2011, BS-5484 dust and vermin proof, complete all as specified and directed by Engineer-in-charge. Notes:(i)MCBs/ MCCBs/ Isolators shall be measured and paid seperately under appropriate items.(ii) The rate of200 Ampscopper bus bar is included in this item and nothing shall be paid extra on this account. |
| 73 | Supply and fixingMCB SPN 40Amps to 63 Amp , rupturing capacity not less than 10 KA\"C\"curve230 V AC, 50 Hz ,ISI Marked,with and including necessary attachment , thimbles etc.complete all as specified and directed by Engineer-in-charge. |
| 74 | Supply and fixing MCB SP 6 to 32 Amps,230 volts ,AC supply, rupturing capacity not less than 10KA,\" C\"Curve ,ISI Marked,with and including necessary attachment , thimbles etc complete all as specified and directed by Engineer-in-charge. |
| 75 | Supplying and fixing MCB TPN40Amps -100 Amps ,415Volt AC, \"C\" curve, ISI Marked,rupturing capacity not less than 10KA, with and including necessary attachment , thimbles etc complete all as specified and directed by Engineer-in-charge. |
| 76 | Supply and fixing Electric / Electronic Bell, ding dong type 230 Volt AC supply,ISI marked complete all as specified and directed by Engineer-in-charge. |
| 77 | Supply and fixing Bell push, piano flush type, 5 Amp 250 Volts, AC supply,ISI marked complete all as specified and directed by Engineer-in-charge. |
| 78 | Supply and Fixing in replacementLED Bulkhead luminaries 10 Watt including LED light driver holder and diffuser, ploycarbonate body and ribbed opal diffuser complete with lamp and all other accessories fitting arrangement as per manufacturer\"s instructions with andincluding electric connection connecting with using flexible copper wire twin core upto ceiling rose/ connector complete all as specified and as directed by Engineer-in- charge.Notes:(a) Contractor has to furnish a replacement warranty of 02 years forLED t fittings complete includingfrom the certifiy date of completion of CA. The product will be replaced free of cost in the following case :-(i) Manufacturing defects.(ii) Failure due to mechanical and electrical impact.(iii) Drop in lumen (or lux at 1 m) below 90% of clamied values of lumen(or lux at 1 m) of the LED /Luminaries.(b) All LED lightmust meet the provision laid down in IS - 16101, 16102 Part -I/II,16103 Part -I, 16104,16105,16106, 16108/2012 and 15885 Part -II / Section 13.(c) Scope of work shall includeLED fittings walls/ceiling which includes needfulT & P andrequired accessories etcif any, complete including making connection, testing etc complete. No extra payment is admissible on these account. |
| 79 | Material and Labourin replacementfor Sub main wiring with two single core of size 6.0 SqmmFRLSH PVC insulated unsheathedwith multistranded copper conductor cable 1100 volts grade ISI Markedincluding cuttting, chasing and grouting , with and including non metallic rigid PVC conduit medium quality of size 25 mm dia conforming to 3537 Part-IISI marked including all fitting such as Tee, Elbow, bend etc drawn in andincludingone single core of size 6.0 SqmmFRLSH PVC insulated unsheathedwith multistranded copper conductor cable 1100 volts grade ISI Marked asin contineous earth conductor cable connected to earth dollycomplete all as specified and as directed by Engineer-in- charge.(Colour code phase-Red, Neutral-black and Earth as Green) complete all as specified and as directed by Engineer-in- charge.Notes:-(a) Cost of PVC conduit , conduit accessories and earth wire included in sub main wiring. (b)Threesingle core 6.0SqmmFRLSH PVC insulated unsheathedwith multistranded copper conductor cable 1100 volts gradeISI Marked with andincluding non metallic rigid PVC conduit of size 25 mmISI Marked dia shall be measured as one length. |
| 80 | Material and Labourin replacement Sub main wiring with two single core of size 4.0 SqmmFRLSH PVC insulated unsheathedwith multistranded copper conductor cable 1100 volts grade ISI Markedincluding cuttting, chasing and grouting , with and including non metallic rigid PVC conduit medium quality of size 25 mm dia conforming to 3537 Part-IISI marked including all fitting such as Tee, Elbow, bend etc drawn in andincludingone single core of size 4.0 SqmmFRLSH PVC insulated unsheathedwith multistranded copper conductor cable 1100 volts grade ISI Marked asin contineous earth conductor cable connected to earth dollycomplete all as specified and as directed by Engineer-in- charge.(Colour code phase-Red, Neutral-black and Earth as Green) complete all as specified and as directed by Engineer-in- charge.Notes:-(a) Cost of PVC conduit , conduit accessories and earth wire included in sub main wiring. (b)Threesingle core 4.0SqmmFRLSH PVC insulated unsheathedwith multistranded copper conductor cable 1100 volts gradeISI Marked with andincluding non metallic rigid PVC conduit of size 25 mmISI Marked dia shall be measured as one length. |
| 81 | Supply and fix ceiling fans, complete with three blade, down rod, accessories 230V, 1200mm sweep, with Squirrel cage induction motorcomplete all as specified and directed by Engineer-in-Charge. |
| 82 | Taking down old unservicable ceiling fan completeand deposit in the store yard of AGE E/M GE861EWS as directed by Engineer-in-charge. |
| 83 | Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers shutters including making circular hole in existing wall to accommodate exhaust fan and necessary civil work and making good the disturbed surfacecomplete all as specified and directed by Engineer-in-Charge. |
| 84 | Supply and Fixingwater heater (Geyser)Auto restrat and safety measures type electrical operated 230/240 Volts25 ltr capacity, BEE 5 star rated complete with all safety equipment and accessories such as safety valve, thermostat, plug top, etc. required for proper functionality & including electric/earth connections and carrying out grounting & complete installations with mounting bolts,nuts including testing after installation completeall as specified & directed by Engr-in- Charge. |
| 85 | Material and Labour forin replacement earthing complete with galvanised steel earth plate electrode 600mm x 600mm x 6 mm thick burried directly in ground to depth of pit not less than 2.25 m below normal ground level with top edge of the plate not less than 1.5 m below normal ground level surrounded from all sides by 15 cm thick packed layer of charcoal / coal dust and common salt filling in alternate layers and connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of GI or steel including GI protection pipe 15mm dia light grade upto the extent of 7.5 metre and connecting to earthing test point, main switch board including GI pipe 20 mm dia medium grade for watering, MS funnel and bringing out the watering pipe upto 30 cm above the normal ground level plugged at top including all fitting including PCC earth pit with PCC 1:2:4 type B-1 using 20mm graded stone aggregate and RCC pit cover including necessary earthwork and excavation in any type of soil complete all as specified as shown in electrical plate No 3 of SSR Part-I and testing on completion.Note:- (i) Earth continuity of GI wire 4 mm including protection pipe up to 7.5 mtrs from earth electrode will be included in unit rate, complete all as specified and directed.(ii) The rate of earth work in soft/loose soili.e. excavation, returing filling and removal, form workis included in this item and nothing shall be paidextra on this account.(iii) PCC chamber shall be constructed at least 1.5 metre away from the earth electrode and pipe for watering shall be provided in slanting manner. (iv) The earth testing arrangement should be done by the contractor as per direction of Engineer-in-charge. |
| 86 | Taking down old unsrviceable service cable/UG cableofcross-sectional area 35sq mm 3.5 core including old uservicable bricks/ PCC concrete cable coverall as specified and directed by Engr-in- Charge. |
| 87 | Supply and laying or fixing or laid in trenches/ ducts/ through pipes/ in floors / underroads/ hard standing /along poles and testing LT cable XLPE, PVC insulated screened,bedded, galvanised steel strip or wire armourd cable(heavy duty) 1100 volt gradewith aluminium conductor having cross sectional area 35 Sqmm3.50 coreconforming to IS-7098 (Part-I -1988) complete allas specified and as directed by Engineer-in-Charge. (Excavation and earth work, sand cushioning & GI pipe shall be measured and paid for separately) |
| 88 | Excavating in trenches, not exceeding 1.5 m wide and not exceeding1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, cableetc. not exceeding 10 sqm on plan and not exceeding 1.5 m in depth and getting out in Hard /dense soil complete all as specified and as directed by Engineer-in- charge. |
| 89 | Returning filling in, approved soft/loose soil, including spreading , levelling, watering and well ramming in layers, each layer not exceeding 25cm in any type of soil complete all as specified and as directed by Engineer-in- charge. |
| 90 | Removing excavated materialnotexceeding 50m and depositing where directedc at a level n exc 1.5 mtr above the starting point . complete all as specified and directed by Engr- in- charge. |
| 91 | Material andLabour sand cushioning, with dry and clean fine river sand for underground cable 8 cm before laying cable and 15 cm after laying and punned to 18 cm after laying of cablecomplete all as specified.(Note:- Punned thickness shall be considered for payment purpose) |
| 92 | Supply and laying Best quality, locally available, sub class ‘B’ burnt clay bricks (Old Size) for cable protection cover, laid flat and dry in trenches over the cable , perpendicular to the direction of cable complete allas specified and as directed by Engineer-in-Charge. |
| 93 | Supply and Laying GI tubing 40mm bore Light grade with all fittings such as clamps laid in trenchs or fixed on wall along pole including fixing arrangement , nut bolts, clamps etc.complete for protection of electic cable / strip complete all as specified and as directed by Engineer - in charge. |
| 94 | Supply and Fixing for PVC connection pipe (Copper chromium plate 8mm dia both end threaded including brass coupling bolt cone washer complete length of pipe not less than 450mm suitahle for holt /cold water system complete all as specified and directed by Engineer-in-charge. |
| 95 | Supply and fixing stop valve cast copper alloy, fancy type, chromium plated with crutch or butterfly handle, screwed down, screwed both end for iron pipe or for brass ferrule15mm bore complete all as specified & directed by Engineer-in-charge. |
| 96 | Supply and fixing bib tap cast copper alloy, chromium plated, fancy type with crutch or butterfly handle with capstan head, screwed down, screwed for iron pipe or for brass ferrule15mm bore complete all as specified & directed by Engineer-in-charge. |
| 97 | Supply and Laying GI tubing 40mm bore Light grade with all fittings such as clamps laid in trenchs or fixed on wall along pole including fixing arrangement , nut bolts, clamps etc.complete for protection of electic cable / strip complete all as specified and as directed by Engineer - in charge. |
| 98 | Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender from total amount of Schedule \"A\"/BOQ |
