Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | B/R PORTION :-Demolition of un-reinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness complete all as specified and as directed. |
| 2 | M & L for Plain Cement concrete type C-2 1:3:6using 40mm graded crushed stone aggregates 75mm thick as in plinth protection, hard standing, sub base, floor finish complete all as specified and as directed. |
| 3 | M&L 75 mm thickPCC(1:4:8)Type D2(using 40mm graded aggregte) in sub floors, sub bases, floors and pavings etc complete all as specified and as directed. |
| 4 | M& L Machine pressed precast concrete interlocking paver block any shapeand size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment complete all as specified and as directed. |
| 5 | M&L sand filling under floors of interlocking tiles including watering and consolidation complete all as specified and as directed. |
| 6 | M&L granite or trap Stone kerb of roughly squared stones of size 20cm x 30cm,dressed so that the maximum depression from a straight edge held against the dressed surface shall not exceed 6mm for top and exposed surfaces of sides and 20mm for the rest of surfaces jointed in cement mortar 1:6 and struck flush complete all as specified and as directed. |
| 7 | M & L 25 mm thick PCC 1:2:4 type B1 (Using 20mm graded stone aggregate) in sub base of floorings complete all as specified and as directed. |
| 8 | Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc complete all as specified and as directed. |
| 9 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed. |
| 10 | Taking down cement plaster or cement lime plaster of any description etc including raking out joints, hacking for key, scrubbing down with water, etc on brick or stone walls etc complete all as specified and as directed. |
| 11 | S&F Non Skid joint free colored ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over and including screed bed or bedding layer 15mm thick in CM 1:6 complete all as specified and as directed.Note: Shade and design/pattern of tiles shall be as directed by GE. |
| 12 | M& L PCC (1:4:8) Type D2 (using 40mm graded aggregte) in foundations, filling and mass complete all as specified and as directed. |
| 13 | M&L for Cement concrete (1:2:4)20 mm graded aggregate type B-2 in foundations, filling and mass concrete complete all as directed with wpc compound mixed in concrete as 3%weight of cement complete all as specified and as directed. |
| 14 | S&F joint free colored ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over and including screed bed or bedding layer 15mm thick in CM 1:6 complete all as specified and as directed.Note: Shade and design/pattern of tiles shall be as directed by GE. |
| 15 | All as per item No 14 above here-in-before but as in vertical surface such as skirting etc. to match with the flooring with CM 1:6 10 mm thick plastering as in backing coat of tile surfaces complete all as specified and as directed. |
| 16 | M&L, joint free coloured glazed ceramic tilesof size 300 x 450mm, 6 to 7mm thick in dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over and including 10mm thick backing coat in CM 1:6 complete all as specified and as directed. |
| 17 | Dismantling stone slab of any description or thickness in floors approns etc laid bedded and pointed in any mortar complete all as specified and as directed. |
| 18 | M & L 18 to 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. Mirror polishing and edge rounded all as per specified for steps and including 20 mm thick screed bed in CM 1:6 complete all as specified and as directed. |
| 19 | M&L Machine cutkota stone slab flooring 20-25mm thick over cement screedbase laid andjointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete andincluding 20 mm thick screed bed in CM 1:6 complete all as specified and as directed. |
| 20 | Taking down Chowkats or frames not exceeding 1.5 Sqm each (Without taking off shutters from the frames) complete all as specified and as directed. |
| 21 | Forming jambs, etc. to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, complete with CM 1:6 complete all as specified and as directed. |
| 22 | S&F Powder coating aluminium frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and as directed. |
| 23 | S&F Poweder coating aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long(1 No) hinges type B-21100mm long (2 No) suitable handle (1 No) complete all as specified and as directed. |
| 24 | S&F Poweder coatingaluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete all as specified and as directed. |
| 25 | S & F in repairsFramed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290 Gde E-165, complete all as specified and as directed. |
| 26 | S & F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed. |
| 27 | S&F 4.8mm thick sheet glass ordinary quality fixing with putty/beading in squarein each pane complete all as specified and as directed. |
| 28 | S & Frepairs Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed. |
| 29 | S&F frosted Sheet glass, ordinary quality 4.8 mm thick and glazing with rubber to Poweder coated aluminiumframe in square/rectanglen exc 0.5 sq. m in each pane complete all as specified and as directed. |
| 30 | Taking down chowkats with shutter (without taking off shutters from the frame) exc 1.5 Sqm but not exc. 4 Sqm each complete all as specified and as directed. |
| 31 | S & F for 35mm thick 2nd class hard woodglazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc divided into squares with plain chamfered or rounded, mitred and rebated shash bars, any numbers, edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR Part I, Section 8 , Clause 8.24 (a), supplied & fitted to chowkats complete all as specified and as directed. |
| 32 | S&F in repairsFactory Made single extruded WPC (Wood polymer composite) solid decorative type flush door shutter of 35 mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powedr/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face ) and 900 N (Edge), minimum compressive strength 50 N.mm2, modulus of elasticity 850 N.mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hings of required size with necessary full body threaded star headed counter sunk S.S screws complete all as specified and as directed. |
| 33 | S&F in repairsFactory Made single extruded WPC (Wood polymer composite) solid decorative type flush door shutter of 30 mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powedr/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face ) and 900 N (Edge), minimum compressive strength 50 N.mm2, modulus of elasticity 850 N.mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hings of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-in-Charge. |
| 34 | S&F in repairsFactory made single extruded WPC(Wood Polymenr Composite) solid door / window / Ceosetory windows and other Frames/chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk)and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated witgh miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame densityy of 750 kg/cum, screw withdrawal strength of 2200 N (Face) and 1100 N (Edge), miimum compressive strength of 58 N/mm2, modules of elasticity 900N.mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of requred dia and length complete as per direction of Engineer-in-charge. (M.S hold fast/lugs or SS dash fasteners shall bne paid for separately) manufacturers instructions and as directed by Engineer-in-Charge. |
| 35 | S & F for Pressed steel frames (size 125x60mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified, supplied and fixed complete all as specified and directed. |
| 36 | S&F Bands, straps, supports or staysfor rainwater, ventilating pipes, including bolts,if required: hooks (stay),heavy,for large gates; hook and pintle hinges:large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securingpurlinstowood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed. |
| 37 | M&L for cutting holes in stone masnory built in cement mortor and making good in CM 1:3 or in cement concrete 1:2:4 tupe B1 as required |
| 38 | M&L for cutting holes in in brick walls built, in cement mortar or cement lime mortar and stone walls built in lime mortar or walls of lime concrete.cementconcrete 1:2:4 tupe B1 as required. |
| 39 | M&L for PCC 1:3:6 type B0 (using 12.50 mm graded stone aggregate) as in cills, copings, apex stone, bed plates kerbs levelling course including waethering, slightly rounded or chamfered angles and throating as directed including mixing water proofing compound (but excluding the cost of WPC) as per manufacturers instrucions all as specified. |
| 40 | S & F in repairs Solid PVC Door Frame of size 50mm X 47mm made out of 5mm wood grain printed PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with printed shee directed by Engineer-in-Charge. |
| 41 | S & F in repairs Factory Made Solid PVC Moulded Door Shutter,with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face supplying & fixing in frame at site as per specification & drawing as directed by Engineer-in-Charge. |
| 42 | S&F, 100mm size medium wt cold rolled mild steel butt hinges, medium weight complete all as specified and as directed. |
| 43 | S&F, 200mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed. |
| 44 | S&F, 300mm long aluminium anodized sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed. |
| 45 | S&F, 150mm size, extruded aluminium anodized handles, fabricated type, complete all as specified and as directed. |
| 46 | S&F 300 mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed. |
| 47 | S&F 150 mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and as directed. |
| 48 | M & L 25mm Harrison rails, mild steel, chromium plated,stainless steel with fixing brackets, stops, rollers etc complete all as specified and as directed. |
| 49 | M & L in repairs for brass chromium platedBrackets, Ends Cap and Holder suitable for 25mm dia Stainless Steel Curtain Rod fancy type complete all as specified and as directed. |
| 50 | M&L preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and as directed. |
| 51 | Cutting chases, in stone walls, pinning in, making good to facing where required and pointing in cement mortpor 1:3 for concealed water tubing and making good, cuting exc, 10 cm but n.exc 20 cm girth complete all as specified and as directed. |
| 52 | S&F 20 mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified including Taking up or down steel tubing and connections including cleaning for refixing or removing to store 15 mm/20 mm bore including brass elbow,teeandcpvc pipe fittings etc complete all as specified and as directed. |
| 53 | S&F 32 mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified including Taking up or down steel tubing and connections including cleaning for refixing or removing to store 25 mm boreincluding brass elbow,teeandcpvc pipe fittings etc complete all as specified and as directed. |
| 54 | S&F Tank Adaptor 32mm dia complete all as specified and as directed. |
| 55 | S&F union of size of 25mm dia complete all as specified and as directed. |
| 56 | S&F Gun metal gate valves with iron wheel head screwed both ends for iron pipe and fixed 25 mm bore complete all as specified and as directed. |
| 57 | Dismantling water tank of capacity exc 500 & n.exc 1000 ltrs complete all as specified and as directed. |
| 58 | S&F 1000 ltrs capacity Rotational moulded polythene water strong tank (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and as directed. |
| 59 | S&F in repairs Ball valves high pressure of PTMT with eppoxy coated Aluminium rod & high density plastic ball screwed for iron pipes and fixed 25 mm bore (Minimum weight 455 gms) complete all as specified and as directed. |
| 60 | Demolition and breaking up of AC/PVC drain pipes 100 mm dia set in CM complete all as specified and as directed. |
| 61 | S&F PVCin repairs (SWR) floor trap diameter of out let 75 mm ,plain with grating including jointing with solvent cement fixed in cement concrete complete all as specified and as directed. (cement concrete shall be measured and paid seperately) |
| 62 | S&F 150 X150 mm Salt-glazed stone ware gully traps, square, type \"P\" complete all as specified and as directed. |
| 63 | S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed. |
| 64 | S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed. |
| 65 | S&F PVC (SWR) pipes single socketed,in any length with rubber ring joints, fixed to walls bore of the pipe 110 mm in repairs complete all as specified and as directed. |
| 66 | S&F PVC (SWR) pipes single socketed,in any length with rubber ring joints, fixed to walls bore of the pipe 75 mm in repairs complete all as specified and as directed. |
| 67 | S&F 110 mm bore PVC (SWR) bends any radiuis complete all as specified and as directed. |
| 68 | S&F 110 mm bore PVC (SWR) bends with access door any radiuis complete all as specified and as directed. |
| 69 | S&F 75 mm bore PVC (SWR) bends any radiuis complete all as specified and as directed. |
| 70 | S&F 75 mm bore PVC (SWR) bends with access door any radiuis complete all as specified and as directed. |
| 71 | S&F 110 mm bore PVC (SWR) junction single, (single T) complete all as specified and as directed. |
| 72 | S&F 110 mm bore PVC (SWR) junction single, (single T) with access door complete all as specified and as directed. |
| 73 | S&F 75 mm bore PVC (SWR) junction single, (single T) complete all as specified and as directed. |
| 74 | S&F 75 mm bore PVC (SWR) junction single, (single T) with access door complete all as specified and as directed. |
| 75 | Supply and fix in repairs Vitreous china premium/ 1st quality wash down water closet wall hung EWC white/ ivory/off white (closed pattern incl all necessary accessories like rag bolts/ gel gasket etc. including flush pipe,bushcomplete in all respect all as specified and directed. S&F 10 lit Vitreous China valveless,syphonic action type,flushing cistern, low level,white, with inlet, ball valve,float and handle including brackets all as specified and directed.S & F in repairs Plastic water closet seat, black, recessed bottom, and cover and mild steel chromium plated or aluminised hinging devicecomplete all as specified and as directed. |
| 76 | S&F in repairs vitreous china squatingpan orrissa pattern size 580 x 440 mm white with integral foot rest, including 10 ltrs PVC valveless, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, flush pipe of polythene of loe or high density or PVC 32 mm dia, , closed pattern with recessed bottom, and cover and mild steel chromium plated or aluminium hanging device complete all as specified and as directed. |
| 77 | S&F in repairs, vitreous china wash hand basin white 550x400mm of size including cutting for and pinning in ends of brackets or erecting stand including brackets, PVC waste pipe and coupling of suitable size including removal of debries off the premises complete all as specified and as directed. |
| 78 | S&Fin repairs kitchen sink made of stainless steel 1mm thick with drainage boardor laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915x460 mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed. |
| 79 | S&F OVAL Counter WASH BASIN of size 460x360x150 mm of CERA CAT No S2030102 with necessary sinkcoupling,waste pipe etc complete all as specified and as directed. |
| 80 | S&F Vitreous China Urinal, full stall type, white Vitreous China urinals, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe including connections to flushing pipe and outgoing pipes fixed in repairs ,Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms), waste coupling of 32 mm discharge pipe (Minimum weight 32mm-45gms), push tap for urinal 15 mm complete all as specified and as directed. |
| 81 | S & Fin repairs of Table Mounted Tall Boy Basin Tap Jaquar Fonte FON-CHR-40021 complete all as specified and as directed. |
| 82 | S&F in repairs, 15mm bore Pillar taps, cast copper alloy, fancy type with capstan heads, chromium plated, screwed down high pressure, with or without lettered \"Hot\" or \"Cold\" with long screwed shanks and fly-nuts, screwed for iron/GI pipe and fixed complete all as specified and as directed. |
| 83 | S&F in repairs, 15mm bore Stop cock / angle valve , cast copper alloy, chromium plated, fancy type, screwed down, high pressure,screwed both ends for iron/GI pipe or for union complete all as specified and as directed. |
| 84 | S&F in repairs,15 mm borefancytype, chromium plated with long shankandcup (concealed type)stop valves of, cast copper alloy, chromium plated, fancy type, screwed down, high pressure,screwed both ends for iron/GI pipe or for union complete all as specified and directed. |
| 85 | S&F in repairs, 125mm size chromium plated shower rose with or without swivel joint complete all as specified and as directed. |
| 86 | S&F in repairs, PVC connections 15mm size with PTMT nuts of length 600mm, complete all as specified and as directed. |
| 87 | S&F in repairs, 15mm bore two way bib taps, long body, fancy type, chromium plated, cast copper alloy, screwed down, screwed for iron/GI pipe or for brass ferrule complete all as specified and as directed. |
| 88 | S&F in repairs, 15mm bore bib taps, long body, fancy type, chromium plated, cast copper alloyscrewed for iron/GI pipe or for brass ferrule complete all as specified and as directed. |
| 89 | S & F in repairs 40 mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc.with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and as directed. |
| 90 | S & FBrass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges fixed in repairs complete all as specified and as directed. |
| 91 | S & F Soap dish vitreous China white, ap proximate size 160x 160x90mmany type, fixed toplugs with chromium plated brass screws complete all as specified and as directed. |
| 92 | S&F brass coat hooks, solid body, 175mm to 250 mm complete all as specified and as directed. |
| 93 | M&L 600mmx450mm bevelled edge frameless mirror of selected quality glass,wixed with chromium plated brass screws and cup washers complete all as specified and as directed. Make: Saint gobin or modi guard ultra mirrors or equivalent as approved by GE |
| 94 | S & F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed. |
| 95 | S&F cornner glass shelf of size 9\"*9\" shelf and frond,circle in design fixed over chromium plated brackets of heavy duty with frond linings with glass fixed in wall with necessary screws make Jaquor ACN CHR 1173 complete all as specified and as directed. |
| 96 | S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide withand railing 60cm long with with aluminium alloy brackets and guard rail complete all as specified and as directed. |
| 97 | Dismantling of wall boards (fibre, Pulp, insulation, plywood etc.) as in cup boards, shelve, pelmet boxes etc complete all as specified and as directed. |
| 98 | S & FFalse Ceiling Frame Work using poweder coated Aluminiumsnap grid of size 605 x 605 mm size of standard aluminium section such as wall angle of size 38mm x 25mm x 2.4mm weighing 0.36 Kg/Rm main/cross tees of size 36.5mm x 25mm x 1.4mm weighing 0.24 Kg/Rm, grid size n.exc. 605 x 605mm suspended with 4mm dia GI wire at interval n.exc. 600mm centre to centre for main & cross tees fixed to roof slab roof truss fixed with suitable size MS hook and fastening bolts etc fixed in ceiling with clips to aluminium snap gridforfixing 6mm thick non Asbestos cement building boards fixed to ceiling frame work complete all as specified and as directed. (Ceiling board measured and paid seperately). |
| 99 | S &F 12 mm thick gyprock false ceiling boards decorative type of suitable size to fixed in poweder coated aluminium /GI /wooden framework etc in ceilingwith necessary screws all as specified including two coats of OBD over primer on ceiling surfaces complete all as specified and as directed. |
| 100 | Supplied and fixed second class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebatedon the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed. |
| 101 | M&L for 25 mm thick Medium density fibre board exterior grade complete all as specified and as directed. |
| 102 | M&L for 18/19 mm thick Medium density fibre board exterior grade complete all as specified and as directed. |
| 103 | M&L for 12mm thick Medium density fibre board exterior grade complete all as specified and as directed. |
| 104 | S&F Decorative laminate 0.9mm type 1 of surface finish glossy, colour and pattern as approved, fixed with approved adhesive as per manufacturer\"s instruction complete all as specified and as directed. |
| 105 | S & F Continuous (piano) hinges of width of flop 30 mm , mild steel, bright finish or electrogalvanised complete all as specified and as directed. |
| 106 | S&F 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished fixed in repairs complete all as specified and as directed. |
| 107 | S&F safety type 150 mmHasp and staple,mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified and as directed. |
| 108 | Dismantling plain or corrugated steel sheeting,any gauge, thickness,including nanital orsimilar pattern roof coverings complete all as specified and as directed. |
| 109 | Dismantling wrought iron or mild steel work of any description complete all as specified and as directed. |
| 110 | S&F steel work in TubularRoof trusses,trussed,purlins, rafters including special shaped washer etc complete using ERW or induction butt weldedtubes confirmingto I.S11611979 grade st 240 complete all as specified and as directed. |
| 111 | S & F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment confirming to Fe-410 W (Grade E-250) quality A complete all as specified and as directed. |
| 112 | S&F Pre-painted galvalume aluminium zinc coating corrugated steel sheet 0.50mm of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed. |
| 113 | S&F Pre-painted galvalume aluminium zinc coatingplain steel sheet 0.50mm of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed. |
| 114 | Preparing new steel iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed. |
| 115 | Dismantling/removing the textile coverings and cover fillets complete all as specified and as directed. |
| 116 | Demolition of plain cement concrete of any description in any position as inpadding concrete, sunken slabs coping, benching, kerbs or mud stops etc and removing the debris outside MOD complete all as specified and as directed. |
| 117 | M&L PCC 1:2:4 type B0 using 12.5 mm graded stone aggregate as in terrace (padding layer ) including water proofing compound200 ml per bag of cementfinished even surface complete all as specified and as directed. Note: Paid and Measured water proofing compound seperately. |
| 118 | M&L for Providing, cement concrete 1:2:4 type B0 (using 12.5mm graded stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges, using water proofing compound at 3% by weight of cement but excluding the cost of WPC ( water proofing compound should be measured and paid seperately) complete all as specified and as directed. |
| 119 | Supply only integral water proofing compound ShaliPlast IW or Equivalentas per manufactures instruction complete all as specified and as directed. |
| 120 | Remove all loose gravel, dirt, oil, grease and foreign matter by jet of dry air and clean the surface mechanically or by grinding to make it smooth before application complete all as specified and as directed. |
| 121 | M&L Repair all cracks by cutting “V” groove and fill with PMC mortar prepared in the ratio of ShaliCrete: Cement : Sand (1 : 2 : 5)using ShaliSBR Latex as bond coat over PMC Mortar complete all as specified and as directed. |
| 122 | Providing and applying brush applied water based PU dispersed polymer modified elastomeric liquid membrane, ShaliUrethaneBTD White Color with Zero VOC to from the membrane in situ at site with 3 layers of monolithic, seam less finish having > 500% elongation. The first layer is to be apply primer Shaliprime BTD @200 Gms per sqm and shall act as the prime coat to fill in the cavities. This can be brush or roller applied. For spray application, using any airless spary system with recommended nozzle size at 30:1 at 2 bar pressure. Providing and applying the 2nd coat @ 1 kg per sqm using the soft brush, roller or Spray system with the recommended nozzle size on to the primed surface . Providing and applying45 Gsm Fiber cloth over the 1st coat, when substrate till the coat is tacky. Providing and applying 3rd coat @ 1 kg per sqm to finish the application for a thickness of 1.2 mm membrane formed in place. The second coat should be applied perpendicular to the first coat for cross linkage complete all as specified and as directed. |
| 123 | Demolition of brick work built in CM including All Quions, arches, pillars etc complete all as specified and as directed. |
| 124 | M & Lmodular Brickworkbuilt in CM 1:6with flyash bricks, straight or curved on plan to any radius in half brick thick walls complete all as specified and as directed. |
| 125 | M & L for Pre-cast cement concrete block masonry with solid blocks, Type C11:3:6 (20mm graded aggregate) exc. 10 cm in width and setting in cement mortar 1:4, complete all as specified and as directed. |
| 126 | Demolition of RCC Concrete of any description and in any position complete all as specified and as directed. |
| 127 | M&L Precast reinforced cement concrete (1:2:4) type B-1 (using 20mm graded stone aggregate ) for landings, cover slabs (for man holes etc.)chullah hoods,chajjas,water troughs,mangers, shelves and similar articles with plain faces manhole cover slabs including necessary form work and set in CM (1:4) complete all as specified and as directed. |
| 128 | M&L fot TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. |
| 129 | M&L for 15 mm thick plastering on fair faces of brick work or concrete surfaces in two layer with 10 mm thick in CM 1:6 and top 5 mm thick in CM 1:4, mixing water proofing compound at 3% by weight of cement (but excluding the cost of WPC) finished the surfaces even and smooth without using extra cement complete all as specified and as directed. |
| 130 | M&L for 15 mm thick plastering in CM 1:4on fair faces of brick work or concrete surfaces in two layer finished the surfaces even and smooth without using extra cement complete all as specified and as directed. |
| 131 | M&L for 15 mm thick plastering in CM 1:6on fair faces of brick work or concrete surfaces in two layer finished the surfaces even and smooth without using extra cement complete all as specified and as directed. |
| 132 | M&L for 10 mm thick plastering in CM 1:3 on fair faces ofconcrete surface as in ceiling including finishing the surface even and smooth without using extra cement complete all as specified and as directed. |
| 133 | M&L for preparing new plastered surface of wall and applyingputtyfor smooth finish wall surface and applying two coat of distemper over a coat of alkali resistant primer complete all as specified and as directed. |
| 134 | M&L for preparing new plastered surface of ceiling and applyingputty finish to obtain smooth finish in ceiling surface and applying two coat of oil bound distemper over a coat of alkali resistant primer complete all as specified and as directed. |
| 135 | M&L for preparing new plastered surface of wall surface and applyingTwo or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed. |
| 136 | M&L for complete removal of existing treatment of wall and and applying two coats of distemper over a coat of primer complete all as specified and as directed. |
| 137 | M&L for complete removal of existing treatment of ceiling and smooth finish ceiling surface and applying two coats of distemper over a coat of primer complete all as specified and as directed. |
| 138 | M&L for complete removal of existing treatment on walls, Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed. |
| 139 | M&L for complete removal of existing treatment of walls and applying two coat of cement based paint over a primer complete all as specified and as directed. |
| 140 | M&L for preparation of new plastered surfaces of walls and applying two coat of cement based paint, complete all as specified and as directed. |
| 141 | M&L for preparing old painted steel and iron surfaces of any description over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint, complete all as specified and as directed. |
| 142 | M&L for preparation of previously treated wood or wood based surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed. |
| 143 | M&L for along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc complete all as specified and as directed. |
| 144 | M&L At points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and as directed. |
| 145 | M&L Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and as directed. |
| 146 | E/M PORTION :-Taking down carefullycopper/ aluminium point wiring (light, fan,socket or power) complete, including fitting & fixtures such as switches with board, ceiling roses, pendents, bell, bell push, lamp holders, regulators, sockets, light fittings etc., removing material from site and making good disturbed surfaces of walls, floors etc complete all as specified and as directed. |
| 147 | M& L for point wiring complete with 1.5 sqmm single core PVC insulatedunsheathed FRLS cable 1100 volts grade ISI marked with multi stranded copper conductor drawn through and including non- metallic rigid PVC conduit medium grade and conduit accessories ISI marked concealed in wall / ceiling/ fixed to roofetc and including provision of 1.5 sqmm PVC insulatedmultistranded unsheathed copper conductor cable FRLS ISI marked as earth continuity conductor, fabricated steel sunken terminal box duly painted made out of 1.60mm thick MS sheet concealed in walls, for housing modular switches, socket outlets, fan regulators etc complete all as specified and as directed for One LED tube light/LED Lamp/Bldg security light controlled by one way switch. (For DSC Billet/ Mess) |
| 148 | All as per Ser item No 147 above but for One Ceiling /Exhaust Fan Point controlled by one one way switch complete all as specified and as directed. |
| 149 | All as per Ser item No 147 above but for 5 amps socket point on independent board complete all as specified and as directed. |
| 150 | All as per Ser item No 147 but for One 3 pin socket outlet 5 Amps on the same board with other switches complete all as specified and as directed. |
| 151 | All as per Ser item No 147 above but for One bell point controlled by one bell push complete all as specified and as directed. |
| 152 | All as per Ser item No 147 above but with 2.5 sqmm cable for 15 amps socket outlet on independent board with 2.5 Sqmm earth continuty wire complete all as specified and as directed. |
| 153 | All as per Ser item No 147 above but with 4 sqmm cable for 20/25 amps Power Unit on independent board with 4 Sqmm earth continuty wire complete all as specified and as directed. |
| 154 | One Light Control By Two way Switch complete all as specified and as directed. |
| 155 | M& L for point wiring complete with 1.5 sq mm single core PVC insulated FRLS cable, with multi standard copper conductors,1100 volts grade,drawn thoroughand including double locking type PVC casing and caping/ conduit pipe and itsaccessories not less than 25 mm wide and including provisoin of 1.5 sqmmPVC insulated copper cable FRLS as earth continuity conductor, including fabricated steel teminal box made out of GI sheet suiatable fixing modular switch sockets etc complete all as specified and as directed for :- |
| 156 | Onelight point controlled by one way switch . |
| 157 | One ceiling fan/ exhaut fan point controlled by one wayswitch. |
| 158 | One 3 pin socket outlet 5 Amps on the same board with other switches. |
| 159 | One 3 pin socket outlet 5 Amps on the Independent board. |
| 160 | One bell/ buzzer point controlled by one push button on the same board with other switch or on independent board. |
| 161 | One Light Control By Two way Switch |
| 162 | All as per Ser item No 155 above but with 4 sqmm cable for 15 amps socket outlet on independent board with 4 Sqmm earth continuty wire complete all as specified and directed. |
| 163 | Supply and fixceiling rose surface backelite three terminals, PVC/polycarbonate, insulated body complete all as specified and as directed. |
| 164 | Supply and fix switch modulartype, 6 Amps 240 volts single pole one way complete all as specified and as directed. Make:- Anchor /Havells |
| 165 | Supply and fix switch modulartype, 6 Amps 240 volts single pole two way complete all as specified and as directed.Make:- Anchor /Havells |
| 166 | Supply and fix socket outlet, 5 pin 6 Amps, Modulartype complete all as specified and as directed. Make :- Anchor /Havells |
| 167 | Supply and fix socket outlet6/16 Amps, 6 in 1, Modulartype complete all as specified and as directed.Make :- Anchor /Havells. |
| 168 | Supply and fix switch modulartype,15/16 Amps 240 volts single pole one way complete all as specified and as directed. Make :- Anchor /Havells |
| 169 | supply and fix modular plates with frame white colour 1 module complete all as specified and as directed. |
| 170 | supply and fix modular plates with frame white colour2 module complete all as specified and as directed. |
| 171 | supply and fix modular plates with frame white colour3 module complete all as specified and as directed. |
| 172 | supply and fix modular plates with frame white colour4 module complete all as specified and as directed. |
| 173 | supply and fix modular plates with frame white colour6 module complete all as specified and as directed. |
| 174 | supply and fix modular plates with frame white colour8 module complete all as specified and as directed. |
| 175 | Supply and fix switch Belll Push modular type single pole complete all as specified and as directed. |
| 176 | Supply and fix stepped type fan regulator electronic modulartype, 2 module,240 Volt complete all as specified and as directed. Make : Havells /Anchor |
| 177 | Supply and fix in replacement 1200mm BLDC 5star rated ceiling fan with regulator enable motor with power inputof 28/30 Watt with 10% tolerance, motor insulation B, 230V , 50Hz, single phase A.C speed 350, Air delivery 215CMM with complete set of 3nos blades, down rod , 2 Nos canopies, shackel kit and all remaining accessories including nut bolts, washers \" including connecting up of cable from ceiling rose or connector to fan complete all as specified and as directed. Make : Ushaor equivalent model in Havells/ cromptonNote: - Old Unserviceable fansshall be deposited to MES store. |
| 178 | Taking down carefully MCB DBs of any size and capacity alongwith MCCBs, MCBs complete all as specified and as directed. |
| 179 | Supply and fix repair VTPN DB , 415 volt,4 way, 100Amp Bus Barwith metal door having facility forMCCB incomming up to 250Aand MCB outgoing complete all as specified and as directed. |
| 180 | Supply and fix TP&N DBs, double door, 415 volt,4 way complete all as specified and as directed. |
| 181 | Supply and fixSP&N DBs, double door, 240 volt,4 waycomplete all as specified and as directed. |
| 182 | Supply and fix SP&N DBs, double door, 240 volt,8 way complete all as specified and as directed.Make:- Legrand |
| 183 | Supply and fixSP&N DBs, double door, 240 volt,12 way including taking down old u/s DBcomplete all as specified and as directed. (Kaveri) |
| 184 | S & Fin repairMCCBs 63 Amps current capacity, 415V, 16 KA, 4 Pole ,thermal magnetic type, along with spreader ternminals complete all as specified and as directed. |
| 185 | M&L in repair for MCB single pole, 240 volts, 6 - 32 Amps, 10 KA C Curve complete all as specified and as directed. |
| 186 | M&L in repair for MCB single pole & neutral 240 volts 32Amps C curve complete all as specified and as directed. |
| 187 | Supply and fix 415V 10KA \"C\" curve miniature circuit breaker (MCB) of TPN 40 AMP and current carrying capacity in the DB complete with connection testing and commissioning complete all as specified and as directed. |
| 188 | Supply and fixing calling bell ding dong single pole AC 230 volt complete all as specified and as directed. |
| 189 | M&L for Sub main wiring with two runs of single core 4 Sqmm multi stranded copper conductor PVC insulated unsheathed, FRLS Cable, 1100 Volts grade and one run of 4 Sqmm multi stranded copper conductor cable as earth continuity conductor drawn into and including non metalic ridig surface / recessed PVC conduit/Casing caping, 25 mm dia and conduit accessories complete all as specified and as directed.(for bathroom 4way DB Kaveri)Note : Two runs of wire, one run of conduit and one run of earth conductor wire shall be measured as one unit length. |
| 190 | M&L for Sub main wiring with two runs of single core 6 Sqmm multi stranded copper conductor PVC insulated unsheathed, FRLS Cable, 1100 Volts grade and one run of 6 Sqmm multi stranded copper conductor cable as earth continuity conductor drawn into and including non metalic ridig surface / recessed PVC conduit/Casing caping, 25 mm dia and conduit accessories complete all as specified and as directed. Note : Two runs of wire, one run of conduit and one run of earth conductor wire shall be measured as one unit length. |
| 191 | Material and labour for 4 sqmm 3 core stainded copper conductor PVC cable drawn through suitable size PVC conduit fixing in wall/roof and making connection with solar water heater electrical backup complete all as specified and as directed. (for solar water heater backup) |
| 192 | Taking down/out unserviceable or serviceable UG Cables of any Cross Sectional Area and Connections including Bricks, GI Pipes, etc. of any descriptions, laid in Trenches and/or fixing with Walls/Poles including Segregating of Serviceable Materials viz Bricks, Cables, GI Pipes, etc. and keep in Safe custody for re-use complete all as specified and as directed. Note : Earth Work shall be Measured and Paid for separately under relevant Items. |
| 193 | M&L for cable in trenches/passing through pipe/on wall , XLPE insulated,heavy duty,galvanised steel strip or wire armoured electric LT cable with stranded aluminium conductor for 1100 volts grade cross sectional area 35 sqmm 3.5 core complete all as specified and as directed.Note : Rate ofthe saddle and clamp for fixing of cable on wallis included in this rate. |
| 194 | All as per Ser item No 186 above but 10 sqmm 2 core(for DSC Parking DB) complete all as specified and as directed. |
| 195 | All as per Ser item No 186 above but 16 sqmm 4 core complete all as specified and as directed. |
| 196 | All as per Ser item No 186 above but 25 sqmm 3.5 core complete all as specified and as directed. |
| 197 | Excavating in Trenches not exc. 1.50 mtr wide and not exc. 1.50 mtr in depth, getting out in Soft / Loose Soil, complete all as specified and as directed. |
| 198 | Returning, Filling in, including Spreading, Levelling, Watering and Well Ramming in Layers not exc. 250mm in Soft/Loose Soil, complete all as specified and as directed. |
| 199 | Removing excavated Materials (Soils) not exc. 50.00 mtr and depositing where directed at a level not exc. 1.50 mtr above the Starting Point in Soil, complete all as specified and as directed. |
| 200 | M&L Sand Cushioning (dry) in Trenches for protec-tion of UG Cables (below, above and around the UG Cable laid in Trenches) of 230mm Spread thickness and consolidated (punned) upto 180mm thickness, complete all as specified and as directed. Note : For the purpose of Payment, Punned thick-ness of Sand Cushioning only shall be Measured and Paid for. |
| 201 | S&F Sub-Class B brick, well burnt, laid breadth-wise along the length of Cable laid in Trenches over Sand Cushion laid for UG Cable Protection, complete all as specified and as directed. |
| 202 | Labour and Tools for intact Removing and Refixingthe same its original position of Solar Waterheater complete set of capacityupto 300 LPD including electrical/water inlet outlet connections and cleaning of solar plates and replacement of electrical backup heating element thermostat, broken glass tube, leakage repair and insulation of hot water tank etc.if any damage caused during the removing and refing wiill be borne by the contractor complete all as specified and as directed. |
| 203 | Supply and Fix Cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of paint complete all as specified and as directed. |
| 204 | Material and labour for Hot water pipe duly insulated with glass wool and aluminium cladding 15 mm bore including all fittings complete all as specified and as directed. |
| 205 | Material and labour for Hot water pipe duly insulated with glass wool and aluminium cladding 20 mm bore including all fittings complete all as specified and as directed. |
| 206 | S&F 15mm bore long body bib cock with flange chormium plated complete all as specified and as directed. |
| 207 | Supply and fixing Tubes, \"mediumgrad\", galvanised, with all fitting; laid in trenches recess/roofs of size 20 mm dia complete all as specified and as directed. |
| 208 | Supply and fixing Tubes, \"mediumgrad\", galvanised, with all fitting; laid in trenches recess/roofs of size 25 mm dia complete all as specified and as directed. |
| 209 | Supply and fix in repair 20 watt intregated LED tube light fitting 4 ft , suitable for single phase 230 Volts, 50 Hz AC supply andmounted on wall or ceiling,complete with all accessories internally prewired and including electrically connection withcopper conductor cable of size 0.5 Sqmm (nominal area) complete all as specified and as directed.Make -: Crompton /Philips/ Wipro/ Vinay. |
| 210 | Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed. |
| 211 | S&F in repair for building security light35 watt LED light fitting, new generation energy saving & environmental friendly long life Versatile pressure die-cast aluminium IP-65 roadway luminaire with high power LEDs as light source & exclusively designed polycarbonate cover alongwith electronic driver, bracket complete after taking down old unserviceable light fitting complete all as specified and as directed. Make:CromptonPhilips / Wipro/ Vinay. |
| 212 | S&F Exhaust Fan of Size 300mm Sweep, Steel body, AC Single Phase heavy duty. 230 Volt with Blades, Frame and Louvers, Providing Connection with and including 3 Core Flexible Copper Conductor Cable of suitable Size and Length , complete all as specified and as directed.Make : Usha or equivalent model in Havells/ Orient Note: - Old Unserviceable fansshall be deposited to MES store. |
| 213 | S&F Exhaust Fan of Size 450mm Sweep, Steel body, AC Single Phase heavy duty. 230 Volt with Blades, Frame and Louvers, Providing Connection with and including 3 Core Flexible Copper Conductor Cable of suitable Size and Length , complete all as specified and as directed.Make : Usha or equivalent model in Havells/ OrientNote: - Old Unserviceable fansshall be deposited to MES store. |
| 214 | Supply and fix Single pole and neutral sheet metal enclosure with a two pin and earth plug and socket complete with one single pole MCB and electrically connecting up fixed in repair complete all as specified and as directed. |
| 215 | M&L for Earthing complete with GI earth plate electrode of size 600x600x6 mm thick buried directly in ground with earth pit not less than 2.25 meter deep below ground level with top edge of plate not less than 1.5 meter below normal ground level connected to GI earth strip of size 25x4 mm earth lead by means of brazing,protected by galvanized iron pipe 40mm bore (Medium grade) allas directed including cement concrete (1:3:6) type C-1 earth pit with precast RCC (1:1.5:3) type A-1 cover slab of size 45 x 45 x 5cm thick reinforced with 8mm dia TMT bars @ 15 cm c/c both ways with 10mm dia mild steel round bar of 30 cm long, bent to shape as lifting handle, funnel,wire mesh, 20 mm bore galvanized iron pipe (medium grade) for watering, charcoal or coke and salt in alternate layers with necessary earth work in soft/loose soil complete all as shown in electrical plate No 3 of SSR Part I including testing on completion all complete as specified and as directed. (GI strip upto 7.5m and removal of old earthing including testing is deemed included in the item) |
| 216 | Material and Labour for Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4mm dia galvanised iron or steel wire complete all as specified and as directed. |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
