|
| 1 | B/R PORTIONComplete removal of entire existing water proofing treatment in any position, any thickness including tarfelt, Plaster, lean concrete, gravels etc. and removing the debries out side MD land complete all as specified and directed. |
| 2 | M&L for plain cement concrete type B1 1:2:4(20mm graded aggregate) 25 mm thick complete all as specified and as directed. |
| 3 | M&L for 10 mm thick rendering in CM 1:4 over concrete surfacesmixed with water proofing compound @ 3% by weight of cement complete all as specified and directed. Note: Water Proofing compound shall be measured and paid for seprately as \"Supply Only\" |
| 4 | M&L Acrylic emulsion polymerof acrylic single component low viscosity polymer for preventing leakages over exisitng/New surface of slab, terrace, exterior, interior wall, Chajjas etc as per following procedure :-(a) Surface & surface preparation : Remove all the loose particles, dirt & dust clean by water, wire brush & mechanical cleaning, grease & oil should be cleaned using solvents,It the surface is previously coated with tar, it should be thoroughtly scraped off.The surface should be dry before application.All the cracks and crevices in the concrete slab to be filledwith polyurethene based sealent with and including application of PU based primer all as directed by Engr-in-Charge.(b) Finish paint : Apply water based polyurethenene modified dispersion (single component cold applied, non toxic, VOC complaint)in 03 coats icluding 01 coat of primer of same materials after dillution of water at 50 % or specific primer matching same material as per manufacturers specificationand as dircted by EIC/GE Make:-Bostic, Berger, Fosroc, Sika, Asian or any other make approved by E-in-C\"s Branch for PU based water proofing treatment. (Ref HQ CE R& D Zonalspecifications dated 21.01.23) |
| 5 | Dismantling plain or corrugated steel sheeting any gauge thickness including Nainital or similar pattern roof covering complete all as specified and directed. |
| 6 | S&F pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering/clading to wall, fixed with self tapping screws as specified complete all as specified and directed. |
| 7 | Demolition of Brickwork or stone masonary built in cement mortar inlcuding all quions, arches, pillars etc. but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and as directed. |
| 8 | M&L for Brickwork with flyash bricks straight or curved on plan exc. 6mtr mean radius built in CM 1:6 complete all as specified and as directed. |
| 9 | M&L for precast cement concrete block masonry with solid blocks of PCC 1:3:6 type C-1 using 20 mm graded stone aggregate, exc. 10 cm in width and setting in CM 1:6, complete all as specified and directed. |
| 10 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed. |
| 11 | M & L forcement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in floor levelling course and in similar situations 25mm thick complete all as specified and as directed. |
| 12 | M&L for Non Skid Ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.06Sqm but not exceeding 0.11Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6 complete all as specified and directed. |
| 13 | M&L Glazed ceramic coloured tiles in vertical surfaces 300 x 450 x 7mm as in dado/skirting etc. and joineted neat in cement slurry and pointed in white or colour cement to match over 10mm thick screed bed in CM 1:4 complete all as specified and as directed. |
| 14 | M&L for Non Skid Ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.11Sqm but not exceeding 0.18Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6 complete all as specified and directed. |
| 15 | M&L for 20mm thick machine cut kota stone slab flooring laid over and including 20mm thick screed base in CM 1:6 and jointed in with grey cement to match the shade of the slab including rubbing, cutting and polishing complete including preparation of old surfaces complete all as specified and directed. |
| 16 | M&L for 20mm thick machine cut kota stone slab as in riser of steps, skiting, dado and pillar laid over and including 15mm thick rendering in CM 1:4 and jointed with grey cementslurry mixed with pigment to match the shade of the slab inlcuding rubbing, cutting and polishing complete all as specified and directed. |
| 17 | Demolition of cement concrete in floors and pavings n. exc. 15cm thickness (below or above ground level) complete all as specified and as directed. |
| 18 | M&L for 75mm thick PCC 1:3:6 type C2 using 20mm graded stone aggregate as in plinth protection complete all as specified and as directed. |
| 19 | M & L for granite 18mm thick black/red colour (of any type) work (table rubbed, and polished) in staircase steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of graniteincl Screed bed or beddinglayer of mortar 20 mmthickin cm (1:6)for laying floor finishes complete all as specified and as directed. |
| 20 | M&L for Machine cut cudappah stone slab 20 to 25mm thick over 20 mm th cement screed base in cm 1:6, laid and jointed with grey cementslurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed. |
| 21 | Taking down chowkats or frames of wooden or steel window not exc 1.5 sqmwith Shutters (without taking off shutters from the frames) complete all as specified and as directed. |
| 22 | Taking down chowkats or frames of wooden or steel windowexc 1.5 sqmbut not exc 4.00 Sqmwith Shutters (without taking off shutters from the frames) complete all as specified and as directed. |
| 23 | S&F three track sliding aluminium window with 4mm thick tinted glass in two shutter and one shutter using stainless steel wire cloth 0.36mm nominal dia & 1.18mm width aperture for mosquito proofing including good quality bearing handle, lock, rubber beading and glazing clips etc using following aluminium powder coated sections conforming to catalogue of \"JINDAL\" or of equivalent make complete all as specified and directed by Engr-in-Charge (Series of aluminium section as per Jindal is (a) Bottom frame - 20620 (b) Top frame & vertical - 20621 (c) Handle (side) - 20606 (d) Shutter inter lock - 20724 (e) Shutter top & Bottom - 20844 (f) Glazing clips - 19352) complete all as specified and as directed. |
| 24 | Supply and fix for aluminium powder coated louvered ventilator with provision of exhaust fan using \"Jindal” aluminium section or equivalent make as specified including glass 3mm thick ordinary quality, frosted and stainless steel wire mesh 0.36mm dia wire and 1.40mm aperture etc complete all as specified and directed. |
| 25 | S&F 2nd class Hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed. |
| 26 | S & F 125 x 60mm size pressed steel frames for doors with one or more rebates incl necessary fixing luges, hinges , lock strike plates etc. complete all as specified and directed. |
| 27 | S & F 105 x 60mm size pressed steel frames for doors with one or more rebates incl necessary fixing luges, hinges, lock strike plates etc complete all as specified and directed. |
| 28 | M&L for PCC 1:3:6 type C1 (using 20 mm graded stone aggregate) as in door frame filling and similar work filling complete all as specified and directed. |
| 29 | M&L for 35mm thickFlush shutters with lipping all around of solid core construction with block board core and ply wood face panels commercial type on both side complete all as specified and as directed. |
| 30 | M&L for 35mm thick 2nd class H/wood gauged and skeleton shutters, open rebated and prepared to receive gauge etc. (with sash bars) edges of ramming plain, chamfered or grouted, fitted with cut of and mitred beads for securing gauge etc of size of members of shutters as specified in SSR Part-I section 8 clause No. 8.2(a) and fitted to chowkats complete all as specified and as directed. |
| 31 | S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm & fixed with stainless steel wire staples complete all as specified and directed. |
| 32 | S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail.Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, and fixing in the frame at site complete all as specified and directed. |
| 33 | Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S square tube, supplying & fixing in opening complete all as specified and directed. |
| 34 | M&L for two coat of synthetic enamel paint over a coat of pink primer including preparation of new/old painted wood surfaces complete all as specified and as directed. |
| 35 | S& F 300 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed. |
| 36 | S&F aluminium anodised barrel tower bolts of extruded section 200 mm long. complete all as specified and directed. |
| 37 | S&F aluminium handles, anodised, cast type, of size 150 mm complete all as specified and directed. |
| 38 | S & F 140 mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and as directed. |
| 39 | S&F 300mm, Brass ordinary rat tail rod pattern springs including roller and roller plate including fixing to door complete complete all as specified and as directed. |
| 40 | S&F in repairs readymade 9 feet pulley operated cloth drying system, aluminium anodised 22mm outer dia pipe, channel assembly, locking system to hide rope knot, ropes 4mm dia HDPE double core & fitting material etc. complete all as specified and directed. |
| 41 | S&F in repairs 25mm dia powder coated aluminium draping rods with domes at ends of rod corrugated of approved qualityincluding brackets fixed in wall including drilling, rawl plug, screws etc. complete all as specified and directed. |
| 42 | Taking down cement plaster, any description on brick, concrete or stonewalls or ceiling including racking out joints, hacking for key, scrubbing down with water etc and removal ofrubbish off complete all as specified and directed. |
| 43 | M & L for Rendering 15mm thick in two layers, 5mm thick using WPC @3% by weight of cement over 10 mm thick on stone masonary work/concretesurfaces in cement mortar 1:4 finished surfaces even and smooth without using extra cement, complete all as specified and directed. |
| 44 | M&Lfor rendering 15 mm thick plaster in CM (1:6) on wallsurface finished even and smooth without using extra cement complete all as specified and as directed. |
| 45 | Supply only WPC complete all as specified and as directed. |
| 46 | M&L for 5mm thick rendering in CM 1:3 on concrete surfaces in ceiling complete all as specified and directed. |
| 47 | M&L for preparation of surfaces and applying 2mm thick wall care putty in two layers on walls/concrete overold /new plaster surfaces internally complete all as specified and directed. |
| 48 | M&L fortwo coats of oil bound distemper over a coat of approved primer on Old/New surfaces of wall complete all as specified and as directed. |
| 49 | M&L fortwo coats of oil bound distemper over a coat of approved primer on old/new surfaces of ceiling complete all as specified and directed. |
| 50 | M&L forapplying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @1.43litre/10sqm over and including priming coat of exterior primer applied @ 0.90litre/10Sqm over Old/new surfaces of wall including necessary scaffolding required for painting work, safety measures etc. complete all as specified and as directed. |
| 51 | S&F for 18mm thick glossy/matte finish solid waterproof MDF board (factory made moulding) and outer side and top sideanf internal sheves shall be of 18mm thick prelam coloured solid MDF board (factory made moulding), for fixing the items fitted in position cupboard and modular kitchen, cabinet shelves comprising of with and including necessary all other fixing arrangement, locking system, door magnet and SS handlesas per requirement at site etc complete all as specified and directed. |
| 52 | S & F continuous piano hinges width of flaps30 mm when opens ,mild steel ,bright finish of electrogalvanised complete all as specified and as directed. |
| 53 | S&F in repair Vitrious china wash down water closet pan (pedestal pattern), any colour with and including and fixing bolts, white seat cover, 10ltr capacity PVC flushing cistern and flush pipe and connection pipe complete all as specified and directed. |
| 54 | S&F in repair Wash hand basin, vitrous china, coloured flat back of size 550 x 400mm encluding cutting for and pining in ends of brackets or erecting stand including brass waste coupling waste pipe, 15mm dia bore pillar taps, and connection pipe, cast copper alloy chromium plated fancy type fixed complete all as specified and as directed. |
| 55 | S&F Looking mirror 600 x 450mm beveled edge mirror of selected quality glass mounted on 6mm thick commercial plywood and fixed to wooden plugs with steel screw, complete all as specified and directed. |
| 56 | S&F in repairs Bib taps fancy type chromium plated for 15mm bore pipe, (small/ long body) as in kichen, bath screwed for iron pipes or for brass ferrule all complete as specified and as directed. |
| 57 | S&F in repairfancy type, chromium plated angular stop cock fixed with wall flange for 15mm bore of pipe complete all as specified and as directed. |
| 58 | S&F in repairfancy type, chromium plated angular stop cock (concealed) fixed with wall flange for 15mm bore of pipe complete all as specified and as directed. |
| 59 | S&F in repairs 450mm long PVC connection 15mm bore with PTMT nuts complete all as specified and as directed. |
| 60 | M&L for 100mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete complete all as specified and as directed. |
| 61 | S & F stainless steel grating doom 100 mm dia complete all as specified and directed. |
| 62 | S & FSheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf corner type three tyres with chromium plated brackets, bracket guard and railing 30cm size incl screws, fixed as in repair complete all as specified and directed. |
| 63 | S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete complete all as specified and directed. |
| 64 | S&F in repair 125mm chromium plated shower roses with shower arm with or without swivel joints, any size including fixing to uPVC/Steel pipe complete complete all as specified and as directed. |
| 65 | S&F in repairs Hand shower (health faucet) (ABS Chromium plated) with 8mm dia, 1.2mtr long flexible tube and wall hook complete all as specified and as directed. |
| 66 | S&F 15mm dia bore, two way bib tap, long body, fancy type, brass chromium plated, with crutch handle, screwed down for uPVC/iron Pipe complete all as specified and directed. |
| 67 | S&F in repairs stainless steel kitchen sink with drainage board of overall size 915x460mm and bowl size 410x330x160mm with plugs,washers and wastes;32 mm dia Low density polyethylene (LDPE) pipes of pressure rating 6 kgf/sq. as in waste pipe including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe complete all as specified and directed. |
| 68 | S&F in repairs 60 cm long brass CP tubular towel rail 20-mm dia D type complete all as specified and directed. |
| 69 | S&F stainless steel chromium plated 6 Pin, 45Cm to 60Cm long hanger fixed to wall with screws complete complete all as specified and as directed. |
| 70 | S&F for steel water tubes, 20mm bore medium grade, galvanized with all fittings and fixed complete to walls, ceiling or laid in floor, complete including taking up or down steel tubing and connections or removal to store complete all as specified & directed. |
| 71 | All as per herein above item here in befor but 15mm complete all as specified and directed. |
| 72 | M&L for cutting chases, pinning in stone, concrete block walls making good to facings where required and pointing in cement mortar 1:3 to concealed water tubingand making good complete all as specified and directed. |
| 73 | S&Fin repairs 500 ltrs capacity, Rotational moulded polythylene water storage tank (cylindrical vertical with closed top) hoisted and in position including ball brass valve 20mm high pressure with polythene float and fly nut complete including dismantling existing water tank and removing to store complete all as specified and directed. |
| 74 | S&F Gun metal globe or gate valve with iron wheel head screwed both ends size 20mm for iron pipe, fixed complete all as specified and directed. |
| 75 | S&F PVC (SWR) pipes, single socketed in any length with rubberring joints fixed to wall, floor of size 110mm bore including taking down old pipe complete all as specified and directed. |
| 76 | S&F PVC (SWR) pipes, single socketed in any length with rubberring joints fixed to wall, floor of size 75mm bore including taking down old pipe complete all as specified and directed. |
| 77 | S&F PVC (SWR) junction, (Single Tee) equal or unequal 110mm bore complete all as specified and directed. |
| 78 | S&F PVC (SWR) junction, (Single Tee) equal or unequal 75mm bore complete all as specified and directed. |
| 79 | S&F PVC (SWR) bends of any radius 110mm bore complete all as specified & directed. |
| 80 | S&F PVC (SWR) bends of any radius 75mm bore complete all as specified & directed. |
| 81 | S&F PVC (SWR) vent cowl 110mm bore complete all as specified & directed. |
| 82 | S&F PVC (SWR) vent cowl 75mm bore complete all as specified & directed. |
| 83 | S&F PVC (SWR) gully traps 125/100mm setting and jointed in cement solventcomplete all as specified & directed. |
| 84 | S&F structural steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes confrming to IS 1161-1979 grade St-240 with necessry angle cleats and girder plate etc complete all as specified and as directed. |
| 85 | M&L for mild steel framed work such as grills, gratings etc. with ends of bars shouldered or riveted or gorged into spikes framed guard bars barredto windows, iron door, ladders framed balusters, walk ways, railing, frame work for water tank and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed. |
| 86 | M&L for Two coats of synthetic enamel paint over a coat of red oxide primer on steel surfaces exc. 10 cm width or girth etc. complete all as specified & directed. |
| 87 | S&F factory made 50mm thick 600 x 600mm manhole cover of 3.0 Tone capacity,KKMD type with additional frame for fixing, including reinforcement as per manufacturer\"s design and set in CM 1:4 and handles including demolition of old existing RCC cover (Reinforcement required to cut as facilitate to domolition) of any description and in any position complete all as specified and directed. |
| 88 | M&L for plain cement concrete type D-2, 1:4:8 (40mm graded stone aggregate) as in sub base 75mm thick complete all as specified and directed. |
| 89 | M & L for glossy finished 60 mm thick factory made chamfered edge cement concrete paver lock of M-35 grade with approved colour desing & pattern as in footpath, parks over and including 50 mm thickness compacted bed of fine sand , compacting and proper embeding/laying of inerlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand and cement concrete filleting to edges of interlocking paver blocks complete all as specified and directed. |
| 90 | S&F for glossy finished chequered cement concrete tiles 30cmx30cmx30mm /20 cm x 20cm x 25 mm(as approved)thick set jointed with grey cement and pigment and pointed in neat cement slurry with andincluding 15 mm thick screed bed of CM(1:6) in floors & cement concrete filleting to edges of Chequered tile hardstanding complete all as specified and as directed. |
| 91 | E/M PORTIONTaking down carefully aluminium / copper point wiring any type for one light, fan, socket power point or buzzer controlled by one switch complete including fitting / fixtures such asswitches, ceiling roses, holder, socket, light fitting etc; for credit and making good disturbed surfaces of walls, ceilings etc complete all as specified and directed. |
| 92 | Taking down old U/s DBs including all fittings or switches of any type and any size complete all as specified and directed. |
| 93 | M & L for point wiringwith 1.5 Sqmm multi stranded copper conductor 1100 V grade, ISI marked, PVC insulated unsheathed cable (with approved colour code) FRLSH cable drawn in & including PVC casing caping (ISI) of size 20/25 on wall or over ceiling/surface (or as at site requirement with casing caping/conduit as per direction of Engr-in-Charge), including sutable size of metal flush box any size and respective modular cover plate all as specified including 1.5 Sqmm FRLSH PVC insulated sheathed solidmulti stranded copper conductor cable/wire for continoues earth wire in green colour and connected to earth dolly forlight point/ceiling fan point / /exhaust fan point / bell point controlled by one switch complete all as specified and directed.Note:- 1. M&L forcutting chases on walls / ceiling /surface and making good disturbed surfaces including finishing with cement mortar (1:3) etc; are deemed to be included in the quoted rate. |
| 94 | All as per herein above itemhere-in- before but for 3 pin 5 Amps switch socket combination on independent board with 1.5 sq mm copper cable complete all as specified and directed. |
| 95 | All as per herein above here - in - before but for 5 Amps socket point on the same board controlled by one switch complete all as specified and directed. |
| 96 | All as per item here-in- before but for 3 pin 15 Amps switch socket combination on independent board with 4.0 sq mm copper cable complete all as specified and directed. |
| 97 | All as per herein above here-in- before but for One light point controlled by two 2-way switches with 1.5 sq mm copper cable complete all as specified and directed. |
| 98 | S & F Modular switch 1 way 6/10 Amp SP,1 module complete all as directed. |
| 99 | S & F Modular switch 2 way 6/10 Amp SP,1 module complete all as specified and directed. |
| 100 | S & F Modular switch 1 way 16/20 Amp SP,1 module complete all as specified and directed. |
| 101 | S & F Modular Fan step regulator, 120W - 2 module complete all as specified and directed. |
| 102 | S & F for ceiling rose surface bakelite 3 phases polycarbonate isolated body complete all as specified and directed. |
| 103 | S & F Modular Socket 6 A 2/3 pin combined, 2 module complete all as specified and directed. |
| 104 | S & F Modular Socket 6 A /16 A-2/3 pin combined 2 module complete all as specified and directed. |
| 105 | S & F Modular Bell push switch 6 Amp1 module complete all as specified and directed. |
| 106 | S & F Bell Buzzer/Ding Dong AC. 230 volts, single pole complete all as specified and directed. |
| 107 | Supply & fix LED Tube light luminaires, 20 watts, lumen output not lessthan 2000 (4 feet), made of anodised extruded aluminium housng, with high transmissivity diffuser, high lumen output, with suitable integrated electronic driver, and operated in single phase, 230 volts, 50HZ, all accessories internally pre-wired and including connecting up with three core twisted flexible copper conductor cable offrom connector and ceiling rose, complete all as specified and directed. |
| 108 | Supply and fixingLED bulb 10 watt B22 type emergency inverter type rechargable (4 hr backup) with lumen output 950 lm and color temp 6500 K suitable for bulb holder complete all as specified and as directed. |
| 109 | Supply and fixing Lamp holder(Angle Holder), PVC/Polycrbonate type with cord grip cap suitable for pendent fitting complete all as specified and directed. |
| 110 | Supply & fix of new generation energy saving and environmental friendly long life 45 W LED building security light made up of pressure die cast aluminium housing with high efficient LED as lighting source and PC cover having top Opening seperate driver compartment with IP66 protection and impact resistance of IK07including necessary brackets (made out of suitable bore GI pipe light grade appx 0.6 meter long bend to shape) nuts, bolts, etc fixed on walls with MS clamp complete all as specified and directed. |
| 111 | M&L for sheet metal enclosure MCB DBs VTPN, 4 way 415 V, with 250 A rated copper bus bar, double door, IP 43, suitable for 160 Amp MCCB 25 kA as incomer as per IEC 61439-3, suitable for flush mounting and surface mounting including taking out complete all as specified and as directed. |
| 112 | S &F MCCB 4 Pole , 415 V , AC , C - curve , Adjustable type, 100 Amps with breaking capacity 25 KA complete all as directed. |
| 113 | M&L for sheet metal enclosure MCB DBs SPN, 16 way 240 V, with 100 A rated copper bus bar, double door, IP 43 as per IEC 61439-3, suitable for flush mounting and surface mounting including taking out complete all as specified and as directed. |
| 114 | M & L for MCB SP 6-32 Amps, 240 volts, 10 kA ISI marked as per IS/IEC 60898-1 2002, C -curve , IP 20 including taking out complete all as specified and directed. |
| 115 | M & L for MCB SPN 32/40 Amps, 240 volts , 10 kA ISI marked as per IS/IEC 60898-1 2002, C -curve, IP 20 including taking out complete all as specified and directed. |
| 116 | Supply and fixingsingle pole and neutral enclouser with atwo pin and earth plug and socket complete with one pole MCB 20 Amps complete all as spd and directed . |
| 117 | Taking down burnt/unserviceable sub main wiring any size complete and making good disturbed surfaces of walls complete all as specified and directed. |
| 118 | M & L for sub main wiring with two single core FRLSH, PVC insulated unsheathed, 1100 Volts grade, copper cable 6 sqmm stranded conductor and drawing through PVC casing caping (MMS ISI marked) of suitable size withaccessoriesincluding continus earth wire FRLSH, PVC insulated unsheathed 1100 volts grade,cable 6 sqmm copperconductor and connected to common earth dolly complete as directedincluding taking down old submain wiring and making good disturbed surface matching with the existing shade/tint complete all as specified and directed. Note :-(i) One run of conduit, two runs of cable and one run of earth wire shall be measured and paid as one unit. |
| 119 | All as per above item but for 2X4.0 sqmm +1x4.0 sqmm earth wire complete all as specified and directed. |
| 120 | All as per above item but for2x1.5 sq mm and 1x1.5 sq mm as earth wire complete all as specified and directed. |
| 121 | M&L for Removing the existing Ceiling fan and servicing, cleaning and spray painting, rewinding & refixing the same with necessary 3 core wire and accessories complete all as specified and directed. |
| 122 | S&F Blades for 1200 mm ceiling fan in place of unserviceable blades including required nuts/washers etc. accessories complete all as specified and directed. |
| 123 | S&F Canopy for 1200 mm ceiling fan in place of unserviceable canopy including required nuts/washers etc. accessories complete all as specified and directed. |
| 124 | S&F down rod 2 feet for 1200 mm ceiling fan in place of unserviceable downrod including required nuts/washers/pins etc. accessories complete all as specified and directed. |
| 125 | Taking down the existing electric meter of Single Phase/ Three phase any capacity and make after disconnecting electrically and S&F new electric meter box (Polycarbonate body suitable for installation of4 x electric meter in one box or as recommended by Engr-in-charge) suitable for 3phase/single phase electric meter including refixing of electric meter in new meter box after servicing & removing of old u/s meter box and made good the discturbed surfaces complete all as specified and directed. |
| 126 | S&F Rigid non mettalic PVC conduit exclusive of boxes (junction/terminal) inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers lock nuts saddles, pipe hooks etc dia 25 mm complete all as specified and directed. |
| 127 | S&F Metal flush box 1/2 module complete all as specified and directed. |
| 128 | Supply and fix TV socket 1 module complete all as specified and directed. |
| 129 | Supply and fix Telephone socket 1 module complete all as specified and directed. |
| 130 | Supply and fix inner and outer modular cover with plate of 1/2 M complete all as specified and directed. |
| 131 | M&L for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cmx 6mm thick buried directly in ground (earth pit not less than 2.25 metre below ground level) with top edge of the earth plate not less than 1.5 metre below ground level, connected to GI earth wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanisediron or steel all as shown in electrical plate No 3 of SSR Part Iconnected to earth test point all as specified including excavation and connected earth work, in soft/loose soil, removing soil upto 50m, PCC1:3:6 type C1 as in pit, 20mm dia GI pipe medium grade for watering pipe, 15mm bore GI medium grade earth lead protection pipe,50mm thick RCC 1:2:4 type B1 cover slab of earth pit reinforced with 8 mm dia TMT Bars @ 10cm C/C both ways and with handle made out of 12mm dia bars,funnel, strainer, alternate layer of charcoal dust and common salt and testing on completion, complete all as specified and directed. |
| 132 | Taking out LT UG Cable from any type of soil cable underground LT any size complete all as specified and directed. |
| 133 | Supply, laying, jointing and testing LT cable in trenches or on poles / walls, XLPE Insulated screened, PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 sqmm 3.5 corefor laying in trenches and poles /walls complete all as specified and directed. |
| 134 | M&L for Road cutting for laying LT cable and make good disturbed surafaces complete all as specified and directed. |
| 135 | Supply & fixing DWC Pipe heavy dutyminimum 32/40 mm dia of required length for protection of cables complete including necessary MS clamps, nuts, boltsfixed complete to walls and ceilings or laid in floorscomplete all as specified and directed. |
| 136 | Supply & fixing GI Pipe light grade 50 mm dia, ISI marked, of required length for protection of cables complete including necessary MS clamps, nuts, bolts and washers etc fixed complete to walls and ceilings or laid in floorscomplete all as specified and directed. |
| 137 | Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m wide and not exceeding 1.5 m depth and getting out soft / loose soil for laying cables / pipes / erection of poles etc. complete all as specified and directed. |
| 138 | Removing excavated material (soil) not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed. |
| 139 | Returning filling in soil including spreading levelling watering well ramming in layers not exceeding 25 cm each. complete all as specified and directed. |
