|
| 1 | Clearing jungle including up rooting of trunk vegetation grass bush wood trees and sapling of girth upto 30cm. Measured at a height of 1 meter above ground level and removal of rubbish upto a distance of 50m. outside the periphery of area cleared as per SI.No. 2.31 (Rates are Including of all taxes but excluding GST) |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil as per SI.No. 2.8.1 (Rates are Including of all taxes but excluding GST) |
| 3 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and olugging with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floor with chlorpyriphos/Lindane E.C. 20% with 1% concentration as per SI.No 2.35.3.1 (Rates are Including of all taxes but excluding GST) |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-lll) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) As per SI no. 4.1.8 (Rates are Including of all taxes but excluding GST) |
| 5 | Brick work in 1:6 (1 cement : 6 coarse sand) with common brunt clay F.P.S. (non modular) brick of class designation-150 in foundation and plinth:(DSR Sp no.6.1>6.1.2) (Rates are Including of all taxes but excluding GST) |
| 6 | Providing and laying in position specifed grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement- All work upto plinth level 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) as SI.no 5.1.2 (Rates are Including of all taxes but excluding GST) |
| 7 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) Above Plinth Lvl as SI No-5.2.2 (Rates are Including of all taxes but excluding GST) |
| 8 | Reinforced cement concrete work in beams, suspended floors, roof having slope upto 15 degree, landings, balconies, shelves, chajjas, lintels, bands, staircases and spiral staircases etc. above plinth level up to floor V level, excluding the cost of centering, shuttering, finishing and reinforcement : in :1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) Above Plinth Lvl as SI No-5.3 (Rates are Including of all taxes but excluding GST) |
| 9 | Excavating , supplying and filling of local earth by mechanical tranford up to a lead up to 5.0km also including ramming and watering of the earth in layer not exceeding 20.0cm in trenche plinth , side of foundation etc.complete SI.no.2.25(a) (Rates are Including of all taxes but excluding GST) |
| 10 | Supplying sand filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. as per SI no 2.27 (Rates are Including of all taxes but excluding GST) |
| 11 | Brick work with common burnt clay bricks of M-150 Class in super structure above plinth level upto floor V level in all shapes and sizes in cement mortar 1:6 ( 1 cement : 6 coarse sand ) 230 TH WALL as per SI no 6.4.2 (Rates are Including of all taxes but excluding GST) |
| 12 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone ) finished with floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. 40 mm thick floor 20 mm nominal size stone aggregate. As SI No. 11.3.1 (Rates are Including of all taxes but excluding GST) |
| 13 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete in Thermo-Mechanically Treated bars of grade Fe-500D or more. As per SI. No.- 5.22.6 (Rates are Including of all taxes but excluding GST) |
| 14 | 12 mm thick cement plaster of mix 1:4 ( 1 cement & 4 course sand ) as per IS 13.4.1 (Rates are Including of all taxes but excluding GST) |
| 15 | 15 mm thick cement plaster of mix 1:4 ( 1 cement & 4 coarse sand ) as per IS 13.5.1 (Rates are Including of all taxes but excluding GST) |
| 16 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture as per Sl no. -13.62.1 (Rates are Including of all taxes but excluding GST) |
| 17 | Providing and laying vitrified floor tiles in different size with water absoption\"s less then 0.08% and conforming to IS.15622 of approved make all colors and shades , laid on 20mm thick cement mortor 1:4 i/c grouting the joints with grey cement slurry @ 3.3 kg/sqm i/c grouting the joints with white cement and matching pigments etc, complete size of tiles (60x60cm) Dsr.11.41.2 (Rates are Including of all taxes but excluding GST) |
| 18 | Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. as per SI no. 11.37 A (Rates are Including of all taxes but excluding GST) |
| 19 | Providing and applying white cement based putty of average thickness 1 mm of approved brand and manufacture over the plastered wall surface to prepare the surface even and smooth complete including cost of all materials, Labour, T&P proper completion work SI.No 13.80 (Rates are Including of all taxes but excluding GST) |
| 20 | Providing and applying 12 mm thick (average) premixed formulated one coat gypsum lightweight plaster having additives and light weight aggregates as vermiculite/ perlite respectively conforming to IS: 2547 (Part - 1 & II) 1976, applied on hacked / uneven background such as bare brick/block/ RCC work on walls & ceiling at all floors and locations, finished in smooth line and level etc. complete.as per SI.No 13.78 (Rates are Including of all taxes but excluding GST) |
| 21 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) as per Sl no. -13.47.1 (Rates are Including of all taxes but excluding GST) |
| 22 | Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, priming coat of approved steel primer, but excluding the cost of other fittings,glass panes complete all as per approved design, (sectional weight of only steel members shall be measured for payment). as per SI no. 10.11.1 (Fabrication of Z-Section steel windows with grill i/c necessary steel fitting such as handles stay etc.) (Rates are Including of all taxes but excluding GST) |
| 23 | Steel work welded in built up sections / framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. In grantings, frames, guard bar, ladder, railing, brackets, gates and similar works as per SI no. 10.25.2 (Fabrication of Grills For windows in 10 mm dia M.S. sq. Bars) (Rates are Including of all taxes but excluding GST) |
| 24 | Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge. as per SI no. 10.31 (M.S. Angle 40x40x5 for door frames) (Rates are Including of all taxes but excluding GST) |
| 25 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part 1) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary. Extra for cutting rebate in flush door shutters as per SI No- 9.20.1 (Rates are Including of all taxes but excluding GST) |
| 26 | Providing and fixing glass panes with putty and glazing clips in steel doors, windows, clerestory, all complete with 4.0 mm thick glass panes. As per IS 10.30.1 (Rates are Including of all taxes but excluding GST) |
| 27 | Centering and shuttering including stutting, propping etc. and removal of form. (Foundation as per SI- 5.9.1) (Rates are Including of all taxes but excluding GST) |
| 28 | Centering and shuttering including stutting, propping etc. and removal of form. (Beam /Band as per SI- 5.9.5) (Rates are Including of all taxes but excluding GST) |
| 29 | Centering and shuttering including stutting, propping etc. and removal of form. (Column as per SI- 5.9.6) (Rates are Including of all taxes but excluding GST) |
| 30 | Centering and shuttering including stutting, propping etc. and removal of form. ( Slab as per SI- 5.9.3 ) (Rates are Including of all taxes but excluding GST) |
| 31 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter. As per SI- 12.41.2 (Rates are Including of all taxes but excluding GST) |
| 32 | Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge. as per SI no-10.28 (Rates are Including of all taxes but excluding GST) |
| 33 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 60 mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern. [DSR-16.91.1] (Rates are Including of all taxes but excluding GST) |
| 34 | Providing and fixing 18 mm thick Granite (gang saw cut) mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab of colour black, Cherry/Ruby red. (Slab area above 0.50 Sq.M.) As per SI no- 8.2.2.2 (Rates are Including of all taxes but excluding GST) |
| 35 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Electric resistance or induction butt welded tubes. SI 10.16.3 (Rates are Including of all taxes but excluding GST) |
| 36 | Providing corrugated G.S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surfaces) excluding the cost of purlins,rafters and trussess and including cutting to size and shape wherever required (1.00 mm thick with zinc coating not less than 275 gm/sqm)SI.No-12.1.1 (Rates are Including of all taxes but excluding GST) |
| 37 | Providing and fixing of cup board shutters with 25mm thick veneered particle board IS :3097 grade 1 including all complete as SI NO 9.130.1 (Rates are Including of all taxes but excluding GST) |
| 38 | S/F of sign board/inauguation stone including all materials,labour and T&P etc. (Rates are Including of all taxes but excluding GST) |
| 39 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require. a) White Vitreous China Flat back wash basin size 550 x 400 mm with single 15 mm C.P. brass pillar tap. DSR-17.7.4 (Rates are Including all taxes but excluding GST) |
| 40 | Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete. Semi rigid pipe. a) 32mm dia DSR-17.28.1.1 (Rates are Including all taxes but excluding GST) |
| 41 | Supplying & Fixing of CP soap tray fixed to the wall with PVC rubber plug with CP brass screws. DSR-18.65 (Rates are Including all taxes but excluding GST) |
| 42 | Providing and fixing Stainless Steel AISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board. 510x1040 mm bowl depth 250 mm. DSR-17.10.1.1 (Rates are Including all taxes but excluding GST) |
| 43 | Providing & fixing PVC pipes conforming to IS make workinh pressure 6 Kg/cm² including testing, labour, T&P and all complete fittings. 110mm dia As per Ch-23 Item-32 (iii) (Rates are Including all taxes but excluding GST) |
| 44 | Providing & fixing PVC pipes conforming to IS make workinh pressure 6 Kg/cm² including testing, labour, T&P and all complete fittings. 75mm dia. As per Ch-23 Item-32 (i) (Rates are Including all taxes but excluding GST) |
| 45 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Exposed on wall 25mm dia nominal dia pipes. DSR-18.7.3 (Rates are Including all taxes but excluding GST) |
| 46 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Exposed on wall 32mm dia nominal dia pipes. DSR-18.7.4 (Rates are Including all taxes but excluding GST) |
| 47 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Exposed on wall 40mm dia nominal dia pipes. DSR-18.7.5 (Rates are Including all taxes but excluding GST) |
| 48 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls 15mm dia nominal dia pipes. DSR-18.8.1 (Rates are Including all taxes but excluding GST) |
| 49 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls 20mm dia nominal dia pipes. DSR-18.8.2 (Rates are Including all taxes but excluding GST) |
| 50 | Providing & fixing CP brass bib cock of approved quality conforming to IS 8931 a) 15mm nominal bore DSR-18.49.1 (Rates are Including all taxes but excluding GST) |
| 51 | Providing & fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. a) 15mm nominal bore. DSR-18.50.1 (Rates are Including all taxes but excluding GST) |
| 52 | Providing and fixing gun metal gate valve with wheel of approved quality. a) 25mm dia nominal bore DSR-18.17.1 (Rates are Including all taxes but excluding GST) |
| 53 | Providing and fixing brass stop cock of approved quality. a) 15 mm nominal bore DSR-18.16.1 (Rates are Including all taxes but excluding GST) |
| 54 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank of approved brand and manufacture with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. DSR-18.48 (Rates are Including all taxes but excluding GST) |
| 55 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. DSR-1.10.1 (Rates are Including all taxes but excluding GST) |
| 56 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire DSR-1.14.2 (Rates are Including all taxes but excluding GST) |
| 57 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. DSR-1.31 (Rates are Including all taxes but excluding GST) |
| 58 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. DSR-1.32 (Rates are Including all taxes but excluding GST) |
| 59 | Supply & fixing of LED tubelight with batten suitable for up to 1x22 Watt LED tubelight fitting including tube on surface complete in all respects. CAT-AAA PWD-1413 (Rates are Including all taxes but excluding GST) |
| 60 | Supply & fixing of 12Watt to 15 Watt indoor recessmounting LED square fitting for Armstrong ceiling having powder coated die cast aluminium housing with extended heat sink diffuser of polycorbonate material and driver set complete in all respects. CAT-AAA PWD-1410 (Rates are Including all taxes but excluding GST) |
| 61 | Supply of AC 1200 sweep fans 230/250 Volts, 50Hz Ceiling Fan including providing nuts, bolts, mounting frame and other accessories ietc. complete as required. PWD-1501(i) (Rates are Including all taxes but excluding GST) |
| 62 | Supply of 300mm sweep Exhaust Fan. (M.R.) (Rates are Including all taxes but excluding GST) |
| 63 | Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. DSR-1.25 (Rates are Including all taxes but excluding GST) |
| 64 | Supplying and fixing 3pin, 5A ceiling rose on the existing junction box/ wooden block including connections etc. as required. DSR-1.33 (Rates are Including all taxes but excluding GST) |
| 65 | Installation, Testing, Commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required. DSR-1.35 (Rates are Including all taxes but excluding GST) |
| 66 | Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Upto 450 mm sweep DSR-1.50.1 (Rates are Including all taxes but excluding GST) |
| 67 | Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, \"C\" curve including connections, painting etc. as required DSR-1.57 (Rates are Including all taxes but excluding GST) |
| 68 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. 4 way (4 + 12), Double door DSR-2.4.1 (Rates are Including all taxes but excluding GST) |
| 69 | Supplying and fixing of 240/415 V, 10 kA, \"C\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. MCB 40 Amp. TPN PWD-1016 (Rates are Including all taxes but excluding GST) |
| 70 | Supply of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following sizes as required complete with in all respect. 35 sq. mm 3-1/2 core PWD-501(K) (Rates are Including all taxes but excluding GST) Please Enable Macros to View BoQ information |
