|
| 1 | Earth work excavation by mechanical means(hydraulic excavator)/manual meansfor foundation, trenches etc., in all types of soils below ground level including shoring, strutting, bailing / pumping of water, leveling, ramming the bottom of excavation, refilling with selected excavated materials in the sides of the foundation in layers, consolidating and disposing off the surplus earth at places as directed within a lead of 50 m all as per drawings and specifications.- up to 1.5m ht |
| 2 | Earth work excavation by mechanical means(hydraulic excavator)/manual means in Soft rockin foundation, trenches etc. including shoring, shrutting wherever required bailing/pumping of water, leveling the bottom of excavation and refilling selected excavated materials and consolidating in the sides of foundation and disposing the surplus materials atplaces as directed within a lead of 2 Kmsall as per drawings and specifications. |
| 3 | Providing and laying plain cement concrete 1:4:8 using 40 mm and down graded stone aggregateat all height including mechanical mixing, leveling, compaction, vibrating,finishing smooth the exposed surfaces of concrete, curing etc complete as per drawings and standard specifications. |
| 4 | Filling with selected earth in layers of not more than 150 mm thick compacted layer, each layer well rammed, watered and consolidated as per drawings and specifications : Selected earth brought from 50 m lead |
| 5 | Providing and laying M20/M25Design mixconcrete with cement content up to 350kg/Cum using 20mm and down graded stone aggregates including Mixing ,Ramming, Compaction, leveling, curing, placing at all lifts, including scaffolding and Finishing smooth all exposed faces complete as per specification. |
| 6 | Providing cutting ,bending placing and tying mild steel, high yield steel reinforcementin RCC works including providing spacer blocks in CM 1:2, binding wires etc.complete at all elevations as per drawings and specifications including dewatering wherever necessary etc complete as per drawings and specifications |
| 7 | Providing ,placing in position and removing Form work for all insitu concrete works such as boundary wall foundtion/columns/beams etc includingscaffolding etc., completeand as per specifications. (measurement for form work shall be the area of forms in contact with concrete surfaces) |
| 8 | Providing and constructing Random Rubble masonry in CM 1:6 using hard granite stones including hammer dressing the stones, providing bond stones as per specifications ,raking out the joints, scaffolding, curing etc., complete as per specifications. |
| 9 | In foundation and basement |
| 10 | Providing and constructing cement concrete block masonry using minimum M5 grade conforming to IS-2185 of latest version , using solid blocks ofspecified size (400mmx200mmx200mm) ,in cement mortar 1:4 by volume, for walls in super structure for all locations and elevations including scaffolding, racking out joints, curing etc completeas perdrawings and specifications |
| 11 | Plastering of external faces of brick work/concrete for boundary wall and exterior surfaces etc in cement mortar 1:4, 20 mm thick including scaffolding, curing, forming grooves of size 25mmx20mm, plaster bands, border, keystone etc wherever required allas per drawings and specifications (Using Crusher sand) |
| 12 | Providing and applying exterior emulsion paint of ACE of ASIAN/ Promise of ICI DULUX/Wall masta of LEWIS BERGER/ Atom 2 in 1 of NIPPON/NEROLAC make& shade in two or more coastover a coat of approved primer to give an even shade as per manufacturer\"s instruction to the external plastered surfaces including preparation of surfaces, scaffolding etc. at all elevations, completeas per drawings and specifications |
| 13 | Providing, fabricating and erection of Structural steel members made out of M.S. angles, flats, plates, pipes, channels, tubes, rods etc conforming to relevant ISetc., includingcost of welding, welding rods, drilling holes, bolts/nuts wherever required and providing and applying two or more coats of approved quality synthetic enamel paint over a coat ofzinc chromate yellow primer etc., as per drawings and specifications |
| 14 | Providing and Fixing roofing at all elevations usingZinc-Aluminium alloy coatedprofile sheetof 0.45 mm thickness ofTATA \"Durashine\"/JSW/Hindalco/Georoofmake of approved colour including all shapes, over laps, side cladding,ridges, eaves board, gutters etc., includingSupplying and Fixing of necessary 6mm dia J or L GI hooks, bolts, nuts, screws, bitumen washers, sealing of joints etc., completeallas per manufacturer\"s recommendations including scaffoldingas per drawings and specifications. (Note: Payment shall be made only to the superficial area. No over laps, corrugations /profile shall be measured) |
| 15 | Providing and filling /spreading Crusher sand 30mm thick (compacted thickness) for preparation of base to lay interlocking precast concrete paver blocks including, leveling, placing, to the required slope, compacting with roller etccompleteas per drawings and specifications. (Payment shall be made only for compacted thickness) |
| 16 | Providing and laying M30 grade 60 mm thick interlocking precast concrete pavers blocks as pr relevant IS of approved shape over a profiled layerto the required line, pattern etc., allas per drawings and specifications |
| 17 | Providing lawn involves planting specified CORIAN/BERMUDA grass and maintaining the same for two months in order to have a healthy growth with the following activities a) providing best quality/ healthy grass suitable for lawn. b) Excavation in all type of soil for a depth of 150mm and filling with soil mixed with cow dung/farmyard manure @ 100kg/100 Sq. Meter for bed preparation .(c) Watering by manually required watering hoses includingcost of labourtools and tackles etc complete.(d) Removing unwanted weeds minimum once in a month. (e) Cutting the grass using lawn mover minimum once in a month more if required). f) Supply and application of fertilizer once (DAP-50gms/Sq. Meter& Urea-50gms/Sq. Meter ). f) Providing and spraying ofapproved quality pesticides on an average of 0.25ml /Sq. Meterincluding cost of labour, spraying pump etc. complete as directed |
| 18 | Supply and fixing of Retro reflective sign boardmadeout of wide angle cubecorner micro prismatic retro refective sheeting conforming to IRC 67-2010 & Type 11 standards of ASTM D 4956-09 fixed over 2mm thick aluminium sheet. The item includes cost of all materials, loading, unloading, lead, lift transportation, fixing arrangements etc complete. 10 years warrenty as per clause 6.90 of IRC 67-2012 for Type XI Retro reflective sheeting from the manufacturer and a certified copy of test reports from an indipendent test laboratory confirming to clause 6.70 of IRC 67-2012 including 3 years outdoor weather exposure report for the retro reflective sheeting offered shall be submitted by the contractor. |
| 19 | Supply and Fixing in position approved quality Stainless Steel of Grade-304 for handrails/other areas as directedusing SS pipes/tubes/balls etc including chasing the walls/floor for Fixing in position and filling the area by cement concrete 1:2:4, finishing with cement plaster in CM 1:4 etc completeas per drawings and specifications |
| 20 | Providing, casting, finishing, curing, hoisting and placing in position 75mm thick precast slabs in cement concrete 1:2:4 using 20mm down size stone aggregate excluding cost of reinforcement but including formwork all complete as per drawings and specifications (The rate shall be exclusive of reinforcement) |
| 21 | Construction of granular sub-base (GSB)by providing close graded Material conforming to specifications conforming to Grade-I (size range 75 mm to 0.075 mm) , mixing in a mechanical mix plant, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness on prepared surface and compacting etc complete as per specifications and directions of Engineer-in-Charge. |
| 22 | Providing, laying, spreading and compacting graded stone aggregate (size range53 mm to 0.075 mm)to wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant, carriage of mixed material by tipper to site, for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge,as per clause 406 of MORT & H specifications complete in all respects. |
| 23 | Providing and applying tack coat using bitumen emulsion conforming to IS:8887 using emulsion pressure distibuter including preparing the surface & cleaning with mechanical broom. with rapid settling emulsion on bitumen surface @ 0.25kg/sqm. as per clause 503 of MORT & H specifications complete in all respects . |
| 24 | Providing and applying prime coat using slow setting bitumen emulsion conforming to IS:8887 on prepared surface of granular base incl;uding clearing the road surface and spraying primer at the rate of 6kg/10sqm,as per clause 502 of MORT & H specifications complete in all respects |
| 25 | Providing and laying Dense graded bituminous macadam 50 mm thick with 100 - 120 THP hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading premixed with bituminous binder at 4.0 to 4.5% by weight of total mix and filler, trnsporting the hot mix to site, laid over a previously prepared surface with a hydrostatic paver finisher with sensor control to the required grade, level and alignment and rolled with smooth wheeled, vibratory and tandom rollers to acheieve the desired compaction as per clause 507 of MORT & H specifications complete in all respects. |
| 26 | Providing and laying bituminous concrete 40mm thickwith 100 - 120 THP hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading premixed with bituminous binder at 5.4 to 5.6% by weight of total mix and filler, trnsporting the hot mix to site, laid over a previously prepared surface with a hydrostatic paver finisher with sensor control to the required grade, level and alignment and rolled with smooth wheeled, vibratory and tandom rollers to acheieve the desired compaction as per clause 509 of MORT & H specifications complete in all respects. |
| 27 | Providing and applying 2.5mm thick road marking trips (retro-reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour ,T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. completeas per drawings and specifications |
| 28 | Providing and Fixing reflective road studs of ‘category B’ Raised pavement markers made out of poly carbonate/ABS moulded body and reflective panels(bi-convex reflectors) with micro prismatic lens capable of providing total internal reflection of the light entering the lens face with retro-reflectance and chromaticity values conforming to ASTMD4280. The reflective raised pavement markers shall also confirm to the MORTH circular no RW/NH.33023/10/97-DOIII dt 11.06.97 and the length ,height and width of the body shall not be less than 100mm,15mm and 90mm and base of marker shall be flat within 1.3mm. The marker shall support a load of 13635Kg tested in accordance with ASTM D4280. Lenses shall be moulded of polycarbonate of methyl methecrylate conforming to ASTM D788. The area of each retro –reflector surface shall be 35+5 degree to base. Each reflector shall have a CIL not less than values specified in table2 of said MoRT &H circular and 2 cylindrical polymer shanks of not less than 20mm diameter and not less than 30mm length shall be provided for better anchorage etc completeas per drawings and specifications |
| 29 | Providing and applying two coats of First Quality synthetic enamel paint of Asian paints/ Lewis Berger/ICI Dulux/NIPPON/NEROLAC make of approved colourover a coat ofprimer on new wood / steel work, suitably prepared for receiving the paint by surface scraping, rubbing applying filler etc., including cost of filler primer, paint etc all completeas per drawings and specifications |
| 30 | Supply ofapproved Ornamental plants (Minimum basic rateof plant shall be Rs.500/No)with Black Graniteflower pot of size 18\"at top and 18\"height Or 18\"x18\" Sq. type or other approved size of 18\" configuration (Minimum basic rateof Granite Pot shall be Rs.1000/No) and maintaining the same for 2 months in order to have a healthy growth with the following activities: a) Supply of approved type of plants in flower pots and placing the same as directed b) Loosening the earth and spreading manure as directed c) Manual watering from the nearby water Supply lines with required watering hoses etc including cost of labour, tools and tackles etc., completed) Providing and spraying of approved quality pesticides on an average of 5ml /plantincluding cost of labour, spraying pump etc. complete . |
| 31 | Writing letters/markings/symbols/Artist Drawings etcon any surface as directedwith approved quality synthetic enamel paint two or more coats including cost of paint of approved colour and brand etc. complete. The cost includes the base paint also. This item has to be executed through professional artist only |
| 32 | Applicable GST Rate (%) Included in the Quoted Price |
