|
| 1 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed. |
| 2 | Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15cm thickness (below or above ground level) complete all as specified and directed by Engr-in-Charge. |
| 3 | Dismantling timber scantling 40 sqcm and over in section in any position framed work, complete all as specified and directed by Engr-in-Charge. |
| 4 | Dismantling unframed work in fillets, rails, posts, rafters, purlins etc under 40sqcm in section, complete all as specified and directed by Engr-in-Charge. |
| 5 | Dismantling boarding any description, fixed with any position with nails, complete all as specified and directed by Engr-in-Charge. |
| 6 | Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed by Engr-in-Charge. |
| 7 | Dismantling Plain or corrugated steel sheeting, any gauge, thickness including nanital pattern or similar pattern roof covering, complete all as specified and directed by Engr-in-Charge. |
| 8 | Taking down chowkhats with shutters (without taking off shutters from the frame) not exc 1.5 sqm each, complete all as specified and directed by Engr-in-Charge. |
| 9 | Taking down chowkhats with shutters (without taking off shutters from the frame) exc 1.5 sqm but not exc 4.00 sqm each, complete all as specified and directed by Engr-in-Charge. |
| 10 | Surface excavation not exc 30 cm deep and averaging 15 cm deep and getting out in hard /dense soil. |
| 11 | Excavation in trenches n. exc 1.5 m wide and n.exc 1.5 m deep for foundation and getting out in hard/dense soil. complate all specified and directed |
| 12 | Returning/filling in including spreading, levelling, watering and well remming in layers n.exc 25 cm in hard/dense soil. complate all specified and directed |
| 13 | Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, in any type of soil. |
| 14 | Surface dressing n exc 15 cm deep in hard/dense soil complete all as specified and directed. |
| 15 | Removing excavated material of soil n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all specified and directed |
| 16 | M&L hard core of gauge n.exc 63mm, deposited, spread and levelled in layers nexc 15 cm thick, using broken stone or boulders, watered and rammed to a true surface. all as specified and directed. |
| 17 | M&L for cement concrete type D-2, 1:4:8in Cement concretein foundations, filling and mass concrete complate all specified and directed |
| 18 | M&L forProviding, cement concrete type B1 (1:2:4) using 20 mm graded aggregate in roof kerbs or mud stops, rounded or chamfered on edges comlete all as secified and directed by Engr-In-Charge. |
| 19 | M&L for provoding cement concrete 1:2;4 type B1 (using 20mm graded aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, all as specified and directed. |
| 20 | M&L for PCC 1:3:6 type C-1(20 mm graded aggregate) precast cement concrete block masonry with solid blocks exc 10 cm in width and setting in CM 1:6 etc complete all as specified and directed. |
| 21 | M&L for Reinforcement cement concrete type B1 1:2:4 in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like |
| 22 | Extra for forming fair finishing drain or channels 30 cm inner girth in cement concrete using extra cement including forms, moulds stopped ends etc.complete all as specified and directed. |
| 23 | Supply only of Liquid water proofing compound for exteenal plastering complete all as specified and directed by engr in charge |
| 24 | S&F of flatFormwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping |
| 25 | Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete. |
| 26 | M&L for second class hard wood in scantling, clean sawn, timber framed and fixed, complete all as specified and directed by Engr-in-Charge. |
| 27 | S & F 2nd class hard wood plain solid straight chowkats and frames, wrought, framed rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and directed. |
| 28 | S&F 30mm thick 2nd class hardwood, Glazed and skelton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shuters as specified in SSR Part-I, Section 8, clause 8.24(a), fittted to chowkats, complete all as specified and directed by Engr-in-Charge. |
| 29 | S & F 30mm thick 2nd class hard wood glazed and skeleton shutters open rebated and prepared to receive glass, gauze etc but divided into squares, edges of framing plain, chamfered or rounded, fitted with cut and mitred beadsfor window, ventilators etc are provided with stiles and rails as specified in SSR Part-1, section 8 clause 8.24(b).complate all specified and directed |
| 30 | S&F 40mm thick 2nd class hardwood, Plain framed, framed, panelled shutter (any number of panels) with panels of timber flat on both sides (feather edged) or of veneered particle board medium density, wood particle board with commercial face veneers fitted to chowkats, complete all as specified and directed by Engr-in-Charge. |
| 31 | S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm widthtuck inside with solvent cement for stiles and plain colour PVC sheets for top rail,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of lain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheetbeading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. all as specified and directed. |
| 32 | S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing. all as specified and directed. |
| 33 | S&F 100mm aluminium anodised, barrel tower bolts of extruded section and fixed, complete all as specified and directed by Engr-in-Charge. |
| 34 | S&F 150mm long almn anodised barrel tower bolts extruded section complete all as specified and directed |
| 35 | S&F 200mm aluminium anodised, barrel tower bolts of extruded section and fixed, complete all as specified and directed by Engr-in-Charge. |
| 36 | S&F 300mm mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and directed by Engr-in-Charge. |
| 37 | S&F 75mm butt hinges, mediam weight, cold rolled mild steel and fixed complete all as specified and directed by Engr-in-Charge. |
| 38 | S&F 125mm butt hinges, mediam weight, cold rolled mild steel and fixed complete all as specified and directed by Engr-in-Charge. |
| 39 | S & F fancy type chromium plated 15mm dia pillar taps fancy type copper alloy with capstan heads,screwed down high pressure, with or without lettered \"hot or cold\" with long screwed shanks and fly nuts, screwed for iron pipe and fixed. |
| 40 | S&F 100mm size Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed.complate all specified and directed |
| 41 | S&F 100mm Aluminium handles, cast type, anodisedcomplete all as specified and directed by Engr-in-Charge. |
| 42 | S&F 150mm size extruded aluminium alloy handles, fabricated type, anodised. handle fabricated type. complate all specified and directed |
| 43 | M&L Mild steelTMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips.complate all specified and directed |
| 44 | M&L TMT bars 6 mm to 8 mm dia., cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips qualityall as specified and directed. |
| 45 | M&L for Plate girder or single stanchions, built up of one beam or channel section with flange plates, caps, bases. splices, angle brackets, cleats and other connections to Fe-290 gde E-165 |
| 46 | S&F of Compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc. coFe-410-W(Gde E-250) quality B all as specified and directed. |
| 47 | S&F of Roof trusses (framed), trussed, purlins, crane gantries, rails and fasteningsand heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. |
| 48 | S & F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete as specified. |
| 49 | Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed. |
| 50 | S&F 0.63mm thick galvanised, corrugated mild steel sheeting with two corrugations side lap,fixed with coach screws and washers in roof, walls etc with grade of zinc coating 275, complete all as specified and directed by Engr-in-Charge. |
| 51 | S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified . |
| 52 | M&L for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified |
| 53 | M&L for 3mm thick cover fillet of standard hard board, 40mm wide and fixing with screws complete all as specified and directed by Engr-in-Charge. |
| 54 | M&L for 6mm thick Plywood, grade BWR, type BB, fixed with screws to timber frame work, complete all as specified and directed by Engr-in-Charge. |
| 55 | M&L for 4mm thick Plywood, grade BWR, type BB, fixed with screws to timber frame work in ceiling, complete all as specified and directed by Engr-in-Charge. |
| 56 | M&L for PCC 100mm thick, type B-2, 1:2:4 (using 40mm graded sone agg) in sub-floors, sub-base, floors and pavings etc.complate all specified and directed |
| 57 | M&L for plain cement concrete 75mm thick type C-2, 1:3:6, (40mm graded stone aggregate) as in plinth protection, finishing cement concrete surfaces even and smooth without using extra cement. complate all specified and directed |
| 58 | M&L for Sub base Cement concrete type D-2, 1:4:8 (40mm graded aggregate) 75 mm thick complete all as secified and directed by Engr-In-Charge. |
| 59 | M&L for PCC 40mm thick, type B-1, 1:2:4 (using 20mm graded stone agg) infloors and pavings etc finished ecen and smooth with using extra cement complete all as specified and directed by engr in charge. |
| 60 | M & L for 350 x 250 x7 mm or 450x350x7mmthick glazed coloured ceramic tiles on vertical surface of wall set and jointed in neat cement slurry and pointed in white/coloured cement to match the shade. (Make; Kajaria/ Orient Bell/ Johnson/ Somany).Note :- Colour and pattern will be decided by GE/Engr-in-charge. Contractor will bought the tiles only after approval ofcolour and pattern of tile by GE/Engr-in-charge. |
| 61 | Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchNote :- Colour and pattern will be decided by GE/Engr-in-charge. Contractor will bought the tiles only after approval ofcolour and pattern of tile by GE/Engr-in-charge. |
| 62 | M&L for Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement andpigment comlete all as secified and directed by Engr-In-Charge. |
| 63 | M&L for Rendering wih CM 1:6, 10mm thick on fair faces of brick work or concrete surfaces to fix the tiles complete all speciffied and directed |
| 64 | M&L rendering mixed with liquid wpc by 0.4% of cement weight 15mm thick in CM 1:4on concrete outer surfaces finished even and smooth without using extra cement . |
| 65 | M&L for screed bed or bedding layer of mortar 15mm thick for laying floor finishes in CM 1:6, complete all as specified and directed. |
| 66 | Material and labour for preparation of newly plastered surfaces of walls and applying two coats of distemper oil emulsion over a coat of alkali resistant primer all as specified. |
| 67 | M&L for Prepairing surfaces plastered or unplastered newly surfaces with two coats of cement base paint over Primimg coat complete all as specified and directed by engr in charge |
| 68 | Supply and Fixing3mm thickFigured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane |
| 69 | M&L for painting new or previously untreated wooden surfaces of any description, not other wise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer. all as specified and directed. |
| 70 | M&L for preparation of new steel Surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coat of synthetic enamel paint over coat of red oxide primer complete all as specified and directed |
| 71 | S&F20mm outer dia 3-layer PP-R Polypropylene random copolymer)concealedpipes SDR 7.4 (PN16) UV stabilized and antimicrobialfusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. |
| 72 | S&F25mm outer dia 3-layer PP-R Polypropylene random copolymer)concealedpipes SDR 7.4 (PN16) UV stabilized and antimicrobialfusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. |
| 73 | S&F PVC water storage tanks of 500 ltrs capacity rotational moulded (multi layered cylindrical vertical with closed top) hoisted and fixed in position all as specified |
| 74 | Supply andfix chromium plated brass Bib taps,cast copper alloywith crutch or butterfly handle, screwed down for iron pipe for 15mm bore GI tubing complete all as specified and directed by Eng-in-charge. |
| 75 | S & F fancy type chromium plated 15mm dia stop valve , cast copper alloy with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule complete all as specified |
| 76 | S&F Gun metal 20mm bore globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed.complate all specified and directed |
| 77 | S&F ball brass valves, high pressure, with polyethene float and flynut complete screwed for iron pipe of 20mm dia all as specified .complate all specified and directed |
| 78 | S&FPVC connection of 15 mm size withPTMT nuts of length 600 mm.complate all specified and directed |
| 79 | S&F PVC (SWR) pipes 75mm dia single sockted in any length with rubber ring joints laid in trenches or floors.complate all specified and directed |
| 80 | S&F PVC (SWR) pipes 110mm dia single sockted in any length with rubber ring joints laid in trenches or floors. complate all specified and directed |
| 81 | S&F PVC (SWR) bends any radius with access door, 75mm dia. complate all specified and directed |
| 82 | S&F PVC (SWR) bends any radius with access door, 110mm dia.complate all specified and directed |
| 83 | S&F75 mm diaPVC (SWR) floor trap, plain with grating including jointing with solvent cement. complate all specified and directed |
| 84 | M&L cement concrete 1:3:6 type C-2 (using 40 mm graded stone aggregate) to bed of drain pipes including packing under and haunching against the sides of pipes, after they are laid and tested for 110 mm bore pipe complete all as specified and directed |
| 85 | S&Fvitreous china wash hand basin white flat back of size 550mmx400 mm including CI brackets and waste pipe complete all as specified and directed |
| 86 | S & F in vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) pipe, etc complete. |
| 87 | S & F 10 litres PVC, valve less, Syphonic action type, Flushing cistern low level, white with inlet ball valve float chain and pull and bracketscomplate all specified and directed |
| 88 | M&L precast cement concrete type B1, 1:2: 4 ( using 20mmgraded stoneaggregate) incover slab for manhole and similar articles with plain faces and set in CM 1:6.complete all specified and directed |
| 89 | Use and waste flat form work to vertical faces of drain/retaining wall and similar work . |
| 90 | Taking down copper/aluminium point wiring (light,fan, socket or power) complete, including fixture and fittings suchasswitches,ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. |
| 91 | M/L for point wiring in casing caping with 1.5sq mm FRLSH PVC insulated unsheathed single core multithreaded copper conductor cable 1100 volts grade incl 1.5 Sq mm PVC insulated unsheathed copper conductor cable as earth continuity conductor drown through in and incl casing caping with its accessories and PVC Boxes for fixing switches/sockets etc for the following: One light/fan point controlled by one No piano type switch5 Amps single pole one way |
| 92 | One socket outlet 5/3 pin 6 AMPS controlled by one switch on the same board. |
| 93 | One socket outlet 5/3 pin 6 AMPS controlled by one switch onindependent board. |
| 94 | All as per item No 2 above but 3 pin socket out let 15/16 Amps on the independent Board all as spfd with single core unsheathed PVC insulated cable multistranded copper conductor of size 2.5 sq mm for phase & neutral & 2.5 sq mm for earth continuity conductor. |
| 95 | S&F Switch Piano Flush button single pole one way 5/6 Amp. |
| 96 | S&F Switch socket combination 2 in 1, 3 pin, 6 and 16 Amp flush type universal.. |
| 97 | S&F Switch socket combination 2 in 1, 6Amp Flush type |
| 98 | S&F ceiling rose surfacebakelite 65mmx50mm 100watt three terminal. |
| 99 | S&F sheet metal enclosure double door for MCB DB single pole and neutral 8 way with 200 Amps rated bus bar 240 volts double door (Metallic) typeincluding taking down old Distribution Board and MCBs all as specified and directed . |
| 100 | S&F MCB SPN 40 Amps 240 volts \"C\" series, 10 KA, 50 Hz.Make:- As approved Make of DB |
| 101 | S&F MCB SP 5 to 32 Amps 240 volts \"C\" series, 10 KA, 50 Hz including connection in the DB and testing/commissioning.Make:- As approved Make of DB |
| 102 | Supply and fixing LED lights fitting 1x 18W, 4 feet, 220V,AC decorative box type with driver, holder including LED light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. |
| 103 | Supply and fixing LED light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple opticscomplete with IP 65/66 protection complete. |
| 104 | M & L for cable route marker with route indication on cast iron disc of 100mm dia and 10mm thick, marked / written for \"LT CABLE 1100 VOLTS\" embosed including indicating direction fixed / bolted to 40mmx40mmx6mm thick MS angle iron support of 0.5m long embedded upto 200mm depth in concrete block of size 200mm x 200mm x 500mm of mix PCC 1:3:6, type C-1 including painting with two coats of synthetic enamel paint over a coat of red oxide primer to exposed steel surfaces complete all as specified and directed. |
| 105 | M&L for earthing complete with galvanised steel earth plate electrode 60cmX60cmX6mm thick, burried directly in ground (earth pit not less than 2.25 metres deep below ground level)with top edge of the plate not less than 1.5 metres below normal groundlevel, connected to galvanised earth lead strip 32x6mm by means of volts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No-5 of SSR Part-I connected to earthing test point all as specified or indicated including excavation and connected earth work in hard/dense soil, PCC 1:3:6 type C-1 as in pit, 20mm dia GI pipe medium grade for watering pipe, 15 mm bore GI medium grade earth lead protection pipe, 50 mm thick RCC 1:2:4 type B-1 cover slab of earth pit reinforced with 8 mm dia TMT bars @ 10 cm C/C both ways and with handle made out of 10 mm dia bars, funnel, strainer,charcoalincluding necessary excavation and earth owrk in any type of soil and testing complete and testing on completion all as specified and directed. |
| 106 | Supply and laying or fixing or passing through pipeXLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade of size 16 sqmm 2 core including taking out old unserviceable cable any type complete all as specified and directed by Engineer in charge. |
| 107 | S&F DWC Pipe 63/50mm outer/ inner dia all as specified and directed by Engr-in-Charge. |
