|
| 1 | M & L for demolition of cement concrete (unreinforced) in ground floors andpavings n exc 15 cm thickness(below or above ground level) and remove the material from site complete all as specified and as directed, |
| 2 | Dismantling wall and ceilling boards(fibre, pilp, insulation etc) or insulation boards/slab/blankets, any thickness including cover filletes and remove froms site etc complete all as specified and as directed by Engr-in-charge. |
| 3 | Dismantling Plain or corrugated steel sheeting of any gauge & any thickness, including Nainital or similar pattern of roof coverings including ridge complete all as specified and as directed. |
| 4 | M & L for demolition of cement concrete (unreinforced) in roofs, floors other than ground floors beams staircases, landing, chajjas and similar suspended workand removing materials from site complete all as specified and as directed by Engineer-in-Charge. |
| 5 | Excavating in post holes (or similar holes) each n.exc 0.5 cum getting out returing filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm in hard/dense soil complete all as specified and as directed by Engr-in-charge. |
| 6 | Excavation in trenches in hard/dense soil n.exc 1.5 mtr wide and n.exc 1.5 mtr deep & getting out soil for taking out/laying of cables etc.complete all as specified & directed by Engr-in-Charge. |
| 7 | Returning, filling in, including spreading, levelling watering and well ramming in layers not exc 25 cm.complete all as specified & directed by Engr-in-Charge. |
| 8 | Removing excavated mateials n.exc 50 mtr & depositing where directed at a level n.exc 1.5 mtr above the starting point.complete all as specified & directed by Engr-in-Charge. |
| 9 | M&L for PCC 1:3:6 type C2 using 40mm graded aggregatesin foundation filling for steel post and mass concrete as in lean concrete complete all as specified and as directed by Engr-in-charge. |
| 10 | Supply only Integral water proofing compound. |
| 11 | M&L for PCC (1:3:6) type C1, using 20mm graded crushed stone aggregate as in hold fast including necessary form work fair finished of exposed surfaces of concrete and making good with existing surfaces. |
| 12 | Providing precast cement concrete type B0 1:2:4 (12.5mm graded aggregate) louvres and jallies, 25mm thick set in CM 1:4 (measured solid), including all mouldings etc all as specified and directed |
| 13 | M & L for 40MM thick PCC type B-0 1:2:4 (12.5 mm Graded stone aggregate) with WPC as in roof padding , chajja repairs complete all as specified and as directed by Engineer-in-Charge.Note: WPC will be paid and measured separately |
| 14 | Providing, RCC Type B0 (1:2:4) (12.5mm graded stone aggregate) in roof kerbs or mud stops, rounded or chamfered on edgesin lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed by Engr-in-charge |
| 15 | M&L for brick work with fly ash modular bricks straight or curved on plan exc 6m mean radius built in CM 1:6 etc complete all as specified and directed. |
| 16 | Supply and laying new dry river sand laid in trenches 8 cm below the cable and 15 cm above the cable and punned to 18 cm as cable cushioning and cover complete all as specified and as directed. |
| 17 | Supply and laying of brick well burnt locally available sub class \"B\" laid over sand cushioning for cable protection in trenches width of brick perpendicular to the length of cable, complete all as specified and directed by Engr-in-Charge. |
| 18 | M & L Granite 16-18mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking plat forms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed. |
| 19 | Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and as directed by Engr-in-charge. |
| 20 | M&L for taking downshutters of any description exc 1 Sqm but n exc 2 Sqm each and refixing in same opening with all accessories (Such as Hinges any size, screws etc) complete all as specified and as directed by Engineer-in-Charge. |
| 21 | S&F factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture, proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. Note: (a) Stainless steel butt hinges and necessary S.S screws shall be paid separately |
| 22 | S&F Factory made decorative lamination finish single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58- Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. . Note: (a) For WPC solid door/window frames,minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable.Variation in profile dimensions on plus side shall be acceptable but no extrapayment on this account shall be made.(b) The quoted rate shall be inclusive of required size and dia of M.S. hold fast/ lugs or SS dash fasteners. |
| 23 | Taking down chowkat or frame with shutter (without taking off shutter from the frame) n.exc. 1.5 sqm each, including making good disturbed surfaces and removing materials from site of work complete all as directed by the Engr-in-charge. |
| 24 | Taking down chowkat or frame with shutter (without taking off shutter from the frame) exc. 1.5 sqm each but n exc 4 Sqm, including making good disturbed surfaces and removing materials from site of work complete all as directed by the Engr-in-charge. |
| 25 | S&F tubular towel rail600mm long PTMT between flanges complete all as specified and as directed |
| 26 | S&F Aluminium anodised towerbolt heavy duty 150 mm long of extruded section etc complete all as specified and as directed |
| 27 | S&F 100 mm stainless steel butt hinges, heavyweight, cold rolled, complete all as specified |
| 28 | S&F Aluminium handles, 150 mm size, cast type anodized complete all as specified and directed. |
| 29 | S&F for Harrison rails, mildsteel, chromiumplated including ,stops,rollers etc complete all as specified and as directed by Engr-in-charge. |
| 30 | S&F Brass chromium plated brackets with fixing brackets for curtain rod complete all as specified and as directed by Engr In Charge. |
| 31 | S&F stainless steel wire cloth 0.45 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainles steel wire stapel etc complete all as secified and as directed |
| 32 | M&L rolled section for Joist, channel, angle, or tee sections,fixed independently,withoutconnecting plates for post, etc. (cut toordinary lengthsi.e. within20mm of the length indicated) conformingFe-410W(GdeE-250) quality B complete all as specified and as directed by Engr-in-charge. |
| 33 | M & L for rolled sections as in main andcross beams, hip and jack rafters;purlins where connectedto common rafters and running railsand guides for sliding doors;fixedwithangle cleats or otherconnecting plates fabrication Fe-410W(GdeE-250) quality B complete all as specified and as directed by Engr-in-charge. |
| 34 | S&F 12 mm dia Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long |
| 35 | S&F Plates of Fe 410W (Gde E-250) (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment to base of column, steel post and truss etc complete all as specified and as directed by Engr-in-charge.. |
| 36 | M&L for Mild steel frame work as in flat iron for fix the steel framwork for eaves board wind tie complete all as specified and directed. |
| 37 | S&F mild steel TMT bars 10mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire not less than 0.9mm dia and confirming to grade 410-O |
| 38 | S & F Anodised aluminium powder coated snap grid 605 x 605mm frame work for false ceiling with 12mm thick GI wire workall as specified and directed by Engr -in-charge. |
| 39 | S & F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed by Engr -in-charge. |
| 40 | M&L Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 etc complete all as specified and as directed |
| 41 | M&L for Powder coated (Minimum thickness of powder coating50micron) Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed by Engr-in-charge.. |
| 42 | S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle,Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge etc complete all as specified and directed. |
| 43 | S & F forMild steel sheet 1.25mm thick 150mm dia eaves gutters, galvanised class 3, half round with rounded edges all as specified and as directed |
| 44 | S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed by Engr-in-charge.. |
| 45 | S&F pre-painted coloured plain profiled Galvalume/Zinc aluminium sheet with min 0.50 mm TCT (total coated thickness), 550 Mpa minimum, yield strength confirming to IS-513 and shall be fixed using hot dip galvanized, self drilling and self tapping screws neoprene and EPDM washers as in ridge covering. Penetrations and laps in sheet shall be sealed by using proper sealant profile etc complete all as specified and directed.Fixing system shall be as per manufacturers instructions and shall be safe against effects of Wind velocity. |
| 46 | M & L for APP based polymeric membrane minimum weighing 3kg/Sqm and 3mm thick reinforced with polyester non woven fabric (weight not less than 150 gm/sqm)laid on surfaceapllied with butuminous primer @0.25Kg per sqm ltr per sqm, by troch application with overlap 100mm on the traverse direction and 75mm on longitudinal direction on exisisting RCC roof surface and applying one coat of aluminium paint over top surfaces of membrane @ 0.11 litre /sqm on top surface complete all as specified and as directed by Engineer-in-Charge. |
| 47 | S & F 4mm thick Non asbestos fibre cement building designer board fixed or laid /inserted to timber /GI/ aluminiumframe work with screws complete all as specified and directed by Engr -in-charge. |
| 48 | M&L for 75 mm thick PCC 1:3:6 type C-2 (40 mm graded stone agg) as inplinth protection, Hard standing finished even and fair complete all as specified and directed by Engineer-in-Charge. |
| 49 | M&L for 25 mm thick cement concrete type B-0 , 1:2:4 ( 12.5 mm graded aggregate ) as in leveling course complete all as specified and directed by Engineer-in-Charge. |
| 50 | Dismantling floor, hearth orwall tiling including cementmortar bedding (but notbacking), removing serviceabletiles to store and rubbish off thepremises complete all as specified and as directed by Engr-in-charge |
| 51 | M&L for joint free Virified Ceramic ultracharge tiles 10 mmthick light shed (square/ rectangular)polished, area of each tilesnot exceeding 0.36 sqm but n exc 0.42 sqm infloors etc. set and jointed inneat cement slurry andpointed in white or coloured cement to matchcomplete all as specified. |
| 52 | Material and labour for joint free Non - skid glazed Ceramic tiles 7 to8 mm thick (square/ rectangular) area of eachtileexceeding 0.06 sqm but notexceeding 0.11 sqm, infloors etc. set and jointed inneat cement slurry andpointed in white or coloured cement to match complete all as specified and as directed. |
| 53 | M & L forMachine cut kota stone slab for flooring 16-18mm thick mirror polishing to give high gloss finish over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specifed and as directed. |
| 54 | Material and labour for glossy finish chequered cement concrete tilessize 300 x 300 x 25mm thick with mixture of white and gray cement in equal proportion and no pigment set, jointed and pointed in neat cement slurry in floorscomplete all as specified. |
| 55 | Material and labour glazed ceramic tiles of size (450x300x7 mm) thick coloured tiles on vertical surfaces set and jointed in neat cement slurryand pointed in white or coloured cement to match the existing surface complete all as specified. |
| 56 | M &L for Rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortal (1.4)with water proof compound for external brick surface finished even & smooth without using extra cement all as specified and directed by Engr-in-charge.Note:- WPC will be measured and paid separately. |
| 57 | Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water and removing from site etc complete all as specified and as directed by the Engr-in-charge. |
| 58 | Material and labour for screed bed or bedding layers of 15 mm thick cement mortar (1:6) for laying floor finishes all as specified. |
| 59 | Material and labour for rendering 10mm thick cement mortar (1:3) receive tiles in vertical surface all as specified. |
| 60 | M &L for Rendering 20 mm thick on fair faces of brick work or concrete surfaces in cement mortal (1.4)with water proof compound for external brick surface finished even & smooth all as specified and as directed by the Engr-in-charge.Note:- WPC will be mesured and paid separately. |
| 61 | M &L for Rendering 15 mm thick other than fair faces of brick work or concrete surfaces in cement mortal (1.6)for internal brick with even & smooth surface all as specified and directed by the Engr-in-charge. |
| 62 | M&L fornewly plastered surface of wall internal appying two coat of white or tinted oil bound distemper over one coat of alkali resistant priming paint over 3 mm thick coat of wall care puttyetc complete all as specified and as directed by the Engr-in-charge. |
| 63 | M&L for prepartion of new plaster surface of wall (External) and apply two coatsof acrylicexterior water proof emulsion paint (camoflauge pattern) over a coat of primer complete all as specified and directed by the Engr-in-charge. |
| 64 | S&F 5.50mm thick sheet glass ofordinary quality and glazing with rubber in squaresexc 0.50 sqm in each pane complete all as specified and as directed by Engr-in-charge. |
| 65 | M&L preparation of old steel surfaces of any description, over 10cm in width or girth,not otherwise described and apply two coats of synthetic enamel paints over a coat of red oxide zinc chrome primer complete all as specified and as directed by Engr-in-charge. |
| 66 | M&L Preparation of old wood and wood based surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint etc complete all as specified and directed by Engineer-in-Charge. |
| 67 | M&L for preparation of existingsurface of wall (External)and applying one coat of acrylic exterior water proof emulsion paint(Camoflauge pattern)complete and including all necessary acaffolding, complete all as specified and directed by the Engr-in-charge. |
| 68 | M&L for preparation of untreated new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint ( 1st grade quality ) over a coat of red oxide primer complete all as specified and as directed. |
| 69 | S/F vitreous China squatting pan, `Orissa\" pattern, size 580 x440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) |
| 70 | Vitreous China wash down watercloset pan (pedestal pattern), white(excluding fixing bolts, flushing cistern and flush pipe) |
| 71 | S&F of PVC valveless, syphonic action type, lowlevel flushing cistern 10 Ltrs capacity with inlet, ball valve, float and handle including brackets (excluding flush/discharge pipe) complete all as specified and directed. |
| 72 | S&F ofVitreous china WHB 550x400mm size white flat back with brackets incl cutting or pinning ends of brackets (excluding waste pipe) complete all as specified and directed. (Make: Hindware or Parry) |
| 73 | S&Fin repairs of PVC connections 15mm size with PTMT nuts of length 450mm to flushing cistern and WHB complete all as specified and directed . |
| 74 | S&F Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) |
| 75 | S&F of 15 mm bore pillar taps fancy type (long neck) cast copper alloy with capstan heads chromium plated screwed down high pressure with or without letter hot or could with long screwed and shanks and fly nuts screwed for iron pipes |
| 76 | S&F Swivel shower of PTMT any colour for fixing with 15mm pipe. (Minimum weight 40gms) with Shower arm 15 mm size, 195mm long with bend of 45degree with flange of PTMT any colour.(Minimum weight 40gms) etc complete. |
| 77 | S&F of 15 mm bore angle stop valves cast copper alloy screwed down high pressured with batterflyhandle screwed both ends for iron pipes fancy type choromium plate. |
| 78 | S&F for bib tap two in one 15 mm bore fancy type chromioum plated with long shank & cup. |
| 79 | S&F in repairs for bib tap 15 mm bore fancy type chromioum plated with long shank & cup. |
| 80 | S&F Health faucet (ABS Body) mild steelchromium plated suitable for 15 mm diapipe with 1.25 metre long flexible tube andABS wall hook including makingconnections and fixed in position completein all respect as specified.and directed by Engr-In-Charge. |
| 81 | S&Fof 600 x 450 mm bevelled edge mirror of seleceted quality glass mounted on 6mm thick PVC board and fixed to wooden plug with CP brass screw and cup washer. |
| 82 | Taking up or down 15mm dia steeltubing and connections, including cleaning for refixing or removal to store complete all as speccified and as directed |
| 83 | Taking up or down 20mm dia steeltubing and connections, including cleaning for refixing or removal to store complete all as speccified and as directed |
| 84 | S/F for 15mm bore GI tubing medium grade with all fittings fixed to walls or laid in floors in concealed type complete all as specified and directed by Eng-In-Charge. |
| 85 | Allas per item No- above but 20mm bore |
| 86 | S & F 100 mm dia CI (sand cast)waste and vent pipes in any length fixed with cement joints laid in trenches or in floor complete all as specified and directed. |
| 87 | S & F CI bend (Sand cast) of any radius with oval access door including jointing with cement joints for (100 mm bore). |
| 88 | S & F CI bend (Sand cast) of any radius with with duck\"s foot or heel rest including jointing with cement joints for (100 mm bore). |
| 89 | S&F 100mm bore CI (Sand cast), junction single, (Single T) equal or unequal complete all as specified and directed |
| 90 | S&F 100mm bore CI Trap (SWR) `P\" or \"S\" type complete all as specified and directed |
| 91 | S&F 110mm bore PVC (SWR) vent cowl complete all as specified and directed |
| 92 | S&F 110mm PVC (SWR) as in drain pipes single socketed in any length with rubber ring joints fixed to walls |
| 93 | S&F110mm bore PVC (SWR) bends any radius complete all as specified and directed |
| 94 | S&F 110mm bore PVC (SWR), junction single, (Single T) equal or unequal complete all as specified and directed |
| 95 | S&F 75 mm PVC (SWR) as in drain pipes single socketed in any length with rubber ring joints fixed to walls or floors |
| 96 | S&F75mm bore PVC (SWR) bends and Tee any radius complete all as specified and directed |
| 97 | S&F grating doom 100mm dia of PTMT (minimum weightt 25 gm) for floor trap/nahani trap all as specified and directed. |
| 98 | S&F of PVC (SWR) floor trap, dia of outlet 75mm plain with grating including jointing with solvent cement etc complete as specified. |
| 99 | S&F Rotational mouldedpolyethylene water storage tank with triple layered White colour with ISI Marked including, plastic lid cover, cylindrical vertical with closed top hoisted and fixed in position of capacity 1000 ltrs including making connections, 20 mm dia ball valves high pressure PTMT with epoxy coated aluminium rod and high density plastic ballscrewed for iron pipe anf fixed (min wt210 gram) complete all as specified in SSR Part I complete all as specified and as directed by Engineer-in-Charge. |
| 100 | S&F CPVC Ball valve (Gate valve) quarter turn screwed both ends for CPVC pipe or for unions of 25 mm dia bore and fixed all complete all as specified and directed by Engr-In-Charge. |
| 101 | S&F Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for 20 mm iron pipe or for unions and fixed. |
| 102 | M & L for galvanised light grade steel conduit of size 80 mm for laying cables in road crossings/drain crossings including necessary clamps/other accessories for laying the conduit along/across the drain, complete all as specified & directed by Engr-in-charge. Make - Jindal/Tata. |
| 103 | Supply, laying and testing cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 95 sqmm, 3.5 core as per IS 7098 incl. lugs/clamps to mount on walls/ ceiling/floors/other accessories necessary for installation, complete all as specified and directed by Engr-in-Charge. |
| 104 | Supply, laying and testing cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sqmm, 4 core as per IS 7098 incl. lugs/clamps to mount on walls/ ceiling/floors/other accessories necessary for installation, complete all as specified and directed by Engr-in-Charge. |
| 105 | M & L for Octagonal Hot Dip Galvanised Iron Tubular pole 7 m long as per IS 4759:1996/IS 2629:1985 / BS 729/ Equivalent, 130 mm bottom dia and 70 mm top dia with vibration damper & minimum sheet thickness 3 mm welded withminimum base plate of size 200 x 200 x 12 mm with 4 no. holes on minimum 200 mm PCD suitable for J type M20 x 600 mm anchor bolts,incl. necessary RCC foundation as per height and its associated earthwork, pole anchored to foundation with anchor bolts/nuts/washers, etc., alongwith suitable elliptical service window mounted with built-in junction boxconsisting of 4 pole terminal block for loop in/loop out connection and MCB back plate and window cover fitted with allen screw to the pole incl. suitable double arm decorative pole bracket for mounting LEDs & necessary conduit for termination of cable complete all as specified & directed by Engr-in-Charge. Make: Utkarsh/Bajaj |
| 106 | S & F of LED Flood light 170 W, 230 V AC outdoor type with thermal management in multiple optics and equipped with IP 66, with impact and corrosion resistant complete with driver and lampincl. fixing on wall with suitable MS flat iron braket or GI pipe in angle complete all as specified and directed. |
| 107 | Supply & Fixing of LED street light fitting 70 W, 230 V AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection incl. fixing on wall with suitable MS flat iron braket or GI pipe in angle complete all as specified and directed. |
| 108 | Supply & Fixing of Building Security Light, LED fitting 35 W, 230 V AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection incl. fixing on wall with suitable MS flat iron braket or GI pipe in angle complete all as specified and directed. |
| 109 | S & F globe shaped post top lantern LED type 30 Watt 230 V AC outdoor type with decorative top for 360 degree indirect light IP 65 protection with impact and corrosion resistant complete with driver and lamp complete, incl. fixing on column with suitable GI pipe complete all as specified and directed. |
| 110 | M & L for Octagonal Hot Dip Galvanised Iron Tubular pole 5 m long as per IS 4759:1996/IS 2629:1985 / BS 729/ Equivalent, 130 mm bottom dia and 70 mm top dia with vibration damper & minimum sheet thickness 3 mm welded withbase plate of size 200 x 200 x 12 mm with 4 no. holes on 200 mm PCD suitable for J type M20 x 600 mm anchor bolts,incl. necessary RCC foundation as per height and its associated earthwork, pole anchored to foundation with anchor bolts/nuts/washers, etc., alongwith suitable elliptical service window mounted with built-in junction boxconsisting of 4 pole terminal block for loop in/loop out connection and MCB back plate and window cover fitted with allen screw to the pole incl. suitable double arm decorative pole bracket for mounting LEDs, necessary conduit for termination of cable complete all as specified & directed by Engr-in-Charge. Make: Utkarsh/Bajaj |
| 111 | M & L of2.5 sqmm x 3 C, copper cable- PVC insulated, sheathed, 650/1100 V grade alongwith sleeves to enclose and insulate the cable for connecting LED flood lights incl. terminal block, complete all as specified & directed by Engr-in-Charge. |
| 112 | Supply and fixing amp rating 240V, 10KA \"C\" curve miniature circuit breaker (MCB) of SP and current carrying capacity 6 AMP in the street light junction box complete with connection testing and commissioning, complete all as specified & directed by Engr-in-Charge. |
| 113 | Supply, Installation, Testing & Commissioning of outdoor type LT Distribution(CPRI Approved as listed in Particular Specification) Panel 415 V, 3-ph, 50 Hz capacity, CPRI approved, made out of CRCA sheet 3.15 mm thick outdoor pedestal type of size minimum 01 x 0.75 x 0.3 m totally enclosed with front & rear opening, hinged doors alongwith suitable locking arrangements, weather and waterproofhaving copper busbars of capacity 400 A for R,Y,B and Neutral with heat proof colour code and mounted on insulators, stickering of switchgears, danger notice plate, including connecting incoming and outgoing cables with 40 x 40 x 6 mm angle legs of length not less than 70 cm fixed to necessary PCC 1:3:6foundation on ground comprising the following:-Incoming(a) MCCB 320A, 4P, 415 V, 50 Hz with rupturing capacity of 35 KA-01 No.Make:L&T/ Havells/ Schneider/C&S electric(b) LED Indicating lamps - 03 Nos. Make: C&S/Neptune/L&T/Vaisnavo(c) Digital Three Phase VIF Meter with VLN, VLL, I1, I2, I3, F measurement -01 No.Make: L&T, Schneider, C&S electricOutgoing(a) MCCB 160A, 4P, 415 V, 50 Hz with rupturing capacity of 35 KA-02 No.Make:L&T/ Havells/ Schneider/C&S electric(b) MCCB 63A, 4P, 415 V, 50 Hz with rupturing capacity of 16 KA-01 No.Make:L&T/ Havells/ Schneider/C&S electric(Note: Cost includes necessary power wiring connections, lugs/ other accessories necessary for LT Panel) |
| 114 | S & F double compression copper stainless steel gland for fixing armoured cable in panel of size 4 core 25 sqmm Al cable. |
| 115 | S & F double compression copper stainless steel gland for fixing armoured cable in panel of size 3.5 core 95 sqmm Al cable. |
| 116 | S & F of rigid non-metallic PVC conduit 20 mm dia exclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks, etc. |
| 117 | Schedule of Credit |
