|
| 1 | Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, intoplinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m. |
| 2 | Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete. |
| 3 | Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete. |
| 4 | Providing and laying cement concrete 1 : 5: 10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering in : Foundations and plinth |
| 5 | Providing and laying damp proof course 38 mm thick with cement concrete 1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 12.5mm nominal size). |
| 6 | Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcementin : |
| 7 | a) M20 (1 cement : 1.5coarse sand : 3 stone aggregate 20 mm nominal size). |
| 8 | Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement. (a).M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 9 | Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement. (a). M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 10 | Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 11 | Reinforced cement concrete in chajjas exceeding 15mm in thickness upto floor two level including centring and shuttering complete but excluding the cost of reinforcement with M20( 1 cement:1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 12 | Centring and shuttering including strutting, propping etc and removal of form work for : |
| 13 | a) Foundation, footings, bases of columns etc. and mass concrete. |
| 14 | b] Column, pillars, posts and struts etc. |
| 15 | c) Lintels, beams, girders, bressumers and cantilevers etc. |
| 16 | Reinforcement of RCC work including bending, binding and placing in position complete. |
| 17 | (a). Mild steel and medium tensile steel bars. |
| 18 | Brick work with best available local bricks in foundations and plinth in cement mortar 1:4 (1 cement : 4 fine sand). |
| 19 | Half brick masonry (with best available local bricks) in cement mortar 1:4 (1 cement : 4 coarse sand) in foundation and plinth. |
| 20 | Extra for half brick masonry in superstructure above plinth level and up to floor two level. |
| 21 | Providing approved best available local wood (Class - B II) work in frames of doors, windows clerestory windows and other frames, wrought framed and fixed in position. |
| 22 | Providing best available local wood (Class - B II) work in frames of false ceiling, partitions and trusses etc, sawn and put up in position. |
| 23 | Providing and fixing 44 mm thick best available local wood Class - B I (19 mm batten and 25 mm bracing) battened and braced doors and windows shutters including providing and fixing necessary bright finished or black enamelled T-hinges, butt hinges, sliding door bolts, tower bolts and handles with necessary bolts and nuts and screws complete. |
| 24 | Providing and fixing panelled, glazed or panelled and glazed shutters for doors, windows and clerestory windows including necessary iron butt hinges with necessary screws. |
| 25 | a) 38mm thick best available local wood class - B I |
| 26 | Providing and fixing MS grills of required pattern in wooden frames of windows etc with MS flat, square or round bars with round headed bolts and nuts or by screws.a) Ornamental grill. |
| 27 | Providing and fixing Iron sliding door bolts anodised transparent or dyed to required color or shade with nuts and screws etc complete.300x16mm |
| 28 | Providing and fixing aluminum Tower bolts anodized or transparent or dyed to required color or shade with necessary screws etc complete.. |
| 29 | a) 300 x 10 mm |
| 30 | b) 250 x 10 mm |
| 31 | Providing and fixing aluminum Handles anodised transparent or dyed to required color or shade with necessary screws etc complete. |
| 32 | 125 mm for Door |
| 33 | 100 mm for Windows |
| 34 | Providing and fixing MS safety hasp and staple with necessary screws etc complete. A) 150 mm. |
| 35 | Providing and fixing 40 x 3 mm flat iron hold fasts 40 cm long including fixing to frame with 10 mm dia bolts, nuts and wooden plugs and embedding in cement concrete block 30 x 10 x 15 cm in 1 : 3 : 6 (1 cement : 3 sand : 6 hard stone chips 40 mm nominal size). |
| 36 | Providing and fixing MS fan clamp type I of 16 mm dia MS bar bent to shape with hooked ends in RCC slabs during lying including painting the exposed portion of loop all as per standard design complete. |
| 37 | Steel work in built up tubular trusses including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer welded and bolted including special shaped washers etc complete (welding to be paid separately). |
| 38 | 25 mm thick cement concrete flooring 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size) finished with a floating coat of neat cement. |
| 39 | Providing corrugated G.I.sheet roofing fixed with galvanised iron J or L hooks, bolts & nuts 8 mm dia with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete, excluding the cost of purlins, rafters and trusses. |
| 40 | Providing ridges or hips 60 cm overall in plain G.I. sheet fixed with galvanised iron J or L hooks, bolts and nuts 8 mm dia. G.I. limpet and bitumen washers complete. . 0.63mm thick |
| 41 | Providing and fixing 4.0 mm thick asbestors plain sheet ceiling of approved quality with necessary nails etc.complete (frame work for base to be paid separately). |
| 42 | Providing and fixing plain, square edged wooden beading 38 mm x 12 mm section with screws of approved quality for ceiling.& Extra for making chamfered edges of beading.a) Best Local approved quality wood |
| 43 | Providing and fixing M.S. Holder bat clamps of approved design of C.I. or S.C.I. pipes embedded in and including cement concrete block 10 cm x 10 cm x 10 cm of 1 : 2 : 4 mix (1 cement : 2 coarse sand: 4 stone aggregate 20mm nominal size) including cost of cutting holes and making good the wall etc. b) 100 mm diameter |
| 44 | 12 mm cement plaster 1 : 4 (1 cement : 4 fine sand). |
| 45 | 15 mm cement plaster 1 : 4 (1 cement : 4 fine sand) on the rough side of single or half brick wall. |
| 46 | Distempering with dry distemper of approved brand and manufacture (two or more coats) and of required shade on new work including priming coat of whiting to give an even shade. |
| 47 | Applying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete. |
| 48 | Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade. |
| 49 | Applying priming coat with ready mixed genuine red lead paint of approved brand and manufacture on steel work. |
| 50 | Painting two or more coats (excluding priming coat) with superior ready mixed paint for steel work of approved brand and manufacture in all shades on new work to give an even shade. |
| 51 | Painting one or more coats on GI sheets with superior ready mixed paint of approved brand and manufacture in white, grey or green shades on old work to give an even shade. |
| 52 | Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth. |
| 53 | Construction of cement concrete drain 15 cm wide and 15 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips or shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering and all exposed surfaces with 12 mm thick cement mortar 1 : 3 (1 cement : 3 coarse sand) including shuttering complete. |
| 54 | Earth work in excavation in foundation trenches not exceeding 1.50 m width or 10 Sq.m. on plan or drains not exceeding 1.50 m in width or 10 Sq.m. on plan including dressing of sides and ramming of bottoms, lift upto 1.50 m including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. a) Ordinary Soil |
| 55 | Providing and laying in foundations and plinth cement concrete 1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering. |
| 56 | Providing and laying cement concrete 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) excluding the cost of centring and shuttering in : |
| 57 | a) Foundations and plinth |
| 58 | b) Walls including attached buttresses, pilasters and their caps andbases and string courses etc. up to floor two level. |
| 59 | Cement concrete flooring 1:2:4(1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement. |
| 60 | a). 40 mm thick |
| 61 | Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 62 | Reinforcement of RCC work including bending, binding and placing in position complete. |
| 63 | a) Cold twisted bars. |
| 64 | Centring and shuttering including strutting proping etc. and removal of form work for: |
| 65 | b) Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. |
| 66 | c) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height). |
| 67 | Providing laying and jointing glazed stone ware pipe grade \"A\" with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete. |
| 68 | a) 100 mm dia SW pipes |
| 69 | Providing and laying cement concrete 1 : 5 : 10 (1 cement : 5 lime sand : 10 graded stone aggregate 40 mm nominal size) all around SW Pipe including bed concrete 15cm thick as per standard design. |
| 70 | a) 100 mm dia SW pipes |
| 71 | Making Soak pit 2.50 m dia 3 m deep with 45 x 45 cm dry brick honeycomb shaft and SW drain pipe 100 mm dia 1.80 m long complete as per standard design. |
| 72 | 12 mm Cement Plaster with 1:3(1cement:3 fine sand) in Cement Mortar |
| 73 | Neat cement Punning |
| 74 | Providing & fixing sand cast iron single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. |
| 75 | a). 100 x 100 x100mm |
| 76 | A. POINT WIRINGPoint wiring in PVC conduit, with modular type switch. Wiring for light point /fan point/exhaust fan point/call bell point with 1.5 Sq.mm FR PVC insultated copper conductor single core cable in surface/recessed PVC conduit,with modular switch, modular switch, suitable size G.I. box and earthing the point with 1.5 sq. mm.FR PVC insulated copper conductor single core cable etc. as required.Group A |
| 77 | Circuit/sub-main wiring in PVC conduit :-. Wiring for circuit/submain wiring alongwith earth wire with the following sizes of PVC insulated copper conductor,single core cable in surface/recessed PVC conduit as required. |
| 78 | 2 x 1.5 sq. mm + 1 x 1.5 sq. mm earth wire (5A Plug). |
| 79 | 2 x 2.5 sq. mm + 1 x 2.5 sq. mm earth wire (for ckt wiring). |
| 80 | 2 x 4 sq. mm + 1 x 4 sq. mm earth wire(for power point). |
| 81 | S/F PVC conduit :-.Supplying and fixing of following sizes of PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. |
| 82 | 25 mm |
| 83 | 32 mm |
| 84 | S/F modular type switch/socket :-.Supplying and fixing following modular switch/socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. |
| 85 | 5/6 Amps Switch |
| 86 | 15/16 Amps Switch |
| 87 | 3 Pin 5/6 Amps Socket |
| 88 | 6 Pin 15/16 Amps socket outlet |
| 89 | S/F modular boxes, Base & Cover Plate:-Supplying and fixing following size/module GI box along with modular base and cover plate for modular switch in recess extr as required.1 or 2 module (75 mm x 75 mm) |
| 90 | S/F modular type electronic fan regulator :- Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. |
| 91 | S/F modular type blanking plate :-Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate etc. as required. |
| 92 | S/F light plug point modular type accessories :- Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess,including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch,connection,painting etc. as required.(For light plugs to be used in non residential buildings). |
| 93 | S/F power plug point modular type accessories:- Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess,including providing and fixing 6 pin 15/16 & 5/6 amps modular socket outlet and 15/16 amps modular switch,connection,painting etc. as required. |
| 94 | ITC fluorescent fitting directly on surface :-Installation, testing and commissioning of pre-wired, fluorescent fitting/compact fluorescent fitting of all types,complete with all accessories and tube etc. directly on ceiling/wall,including connection with 1.5 sq. mm FR PVC insualted,copper conductor,single core cable and earthing etc. as required. |
| 95 | ITC ceiling fan :-Installation, testing and commissioning of ceiling fan including the down rods of standard length (upto 30 cm) with 1.5 sq. mm FR PVC insualted,copper conductor,single core cable and earthing etc. as required. |
| 96 | Installation of exhaust fan in the existing opening, includingmaking good the damage, connection, testing, commissioningetc. as required.Upto 450 mm sweep |
| 97 | S/F call bell/buzzer :-Supplying and fixing call bell/buzzer suitable for single phase , 230 volts, complete as required. |
| 98 | S/F steel conduit :- Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. |
| 99 | 20 mm |
| 100 | 25 mm |
| 101 | Wiring in existing conduit :- Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. |
| 102 | 1 x 1.5 sq. mm |
| 103 | 2 x 1.5 sq. mm |
| 104 | Furniture a) Bed |
| 105 | b) Almirah |
| 106 | c) Study Table |
| 107 | d) Arm Chair |
| 108 | e) Dining Table |
| 109 | f) Dining Chair |
| 110 | g) Tea Table |
| 111 | h) Sofa Set |
