Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Works |
| 2 | EXCAVATION upto 1.50 Metre for foundation such as footing, pedestals, walls, drains, columns, ramps, plinth beams, cable trenches in Dense or Hard soil MECHANICALLY but other than hard rock including shoring, strutting, sorting out and stacking useful material, dewatering where required, cutting vegetation up to 1.5m ht if required and disposing off the excavated stuff upto all lead and lift.Note- All types of soil that can be removed by JCB/ Poclain bucket shall be classified under this item. |
| 3 | EXCAVATION 1.50 to 3.00 Metre for foundation such as footing, pedestals, walls, drains, columns, ramps, plinth beams, cable trenches in Hard Murrum MECHANICALLY but other than hard rock including shoring, strutting, sorting out and stacking useful material, dewatering where required, and disposing off the excavated stuff upto all lead and lift. |
| 4 | EXCAVATION 1.50 to 3.00 Metre for foundation such as footing, pedestals, walls, drains, columns, ramps, plinth beams, cable trenches in Soft rock not requiring blasting but other than hard rock including shoring, strutting, sorting out and stacking useful material, dewatering where required, and disposing off the excavated stuff upto all lead and lift |
| 5 | EXCAVATION 3.00 to 5.00 Metre for foundation such as footing, pedestals, walls, drains, columns, ramps, plinth beams, cable trenches in Soft rock including shoring, strutting, sorting out and stacking useful material, dewatering where required, and disposing off the excavated stuff upto all lead and lift |
| 6 | EXCAVATION 3.00 to 5.00 Metre for foundation such as footing, pedestals, walls, drains, columns, ramps, plinth beams, cable trenches in Hard rock including shoring, strutting, sorting out and stacking useful material, dewatering where required, and disposing off the excavated stuff upto all lead and lift |
| 7 | FILLING with selected & approved available excavated earth (excluding rock) in excavated pits, trenches, in plinth, sub-base for of roads,drains, manhole, sumps, or where required with approved locally available materials including spreading in layers not exceeding 200mm, watering, ramming, compacting mechanically using 2 ton compactor etc, complete.Measurements for net volume of space occupied by filling.If desired by the engineer-in-charge the contractor shall at his own expense carry out modified proctor compaction test to determine the maximum dry density.The criteria for acceptance of filling shall be compacting to 95% modifiedProctor density with use of mechanical roller/rammer etc complete as directed and instructed by Engineer-in-charge. Volume of material filled to be measured for payment. |
| 8 | FILLING with selected & approved Murrum material brought by Contractor from outside client\"s premises, including Identification ofBorrow pits and including Royalty charges & or duties as per requirement oflocal authority, in foundations, excavated pits, trenches, in plinth, sub-base for of roads,drains, manhole, sumps, or where required with approved locally available materials including spreading in layers not exceeding 200mm, watering, ramming, compacting mechanically using 2 ton compactor etc, complete.Measurements for net volume of space occupied by filling.If desired by the engineer-in-charge the contractor shall at his own expense carry out modified proctor compaction test to determine the maximum dry density.The criteria for acceptance of filling shall becompacting to 95% modifiedProctor density with use of mechanical roller/rammer etc complete as directed and instructed by Engineer-in-charge. Volume of material filled to be measured for payment. |
| 9 | Providing and laying RUBBLE SOLING wherever required in foundation and plinth including hand packing fillings interstices with chips and sand.Watering and compacting to consolidated thickness, etc complete as directed by engineer-in-charge |
| 10 | Providing material and labour for laying PLINTH PROTECTION including excavation of 30 cm depth and Filling with dry bricks bats of 20 cm thick and top layers C.C. 1:2:4 ( 1 cement 2 coarse sand: 4 graded stone aggregate 20m nominal size)50mm thk finished in proper grade and slop etc. completeas directed by engineer-in-charge |
| 11 | Carring out plinth treatment to post construction / existing structure by spraying chemical solution for termite control treatmentincluding labour and material consistment with I.S.I specification.Using Chlordene and Chiorpurfiles 20 EC. As Per 6131_paret-II Consentration Weight one percent is recommended i.e one LTR. 20 EC chemical emulsion with 19 liter give 1 % concrentration inclusive of one LTR. chemical emulsion appication at the rate of 5 LTR. chemical / Sqm of surface is recommended as per I.S. treated Plinth area of structureto be measured for payment as directed by engineer-in-charge |
| 12 | Providing and laying Granular subbase (GSB) for preparing base of road,trenches, in plinth, sub-base for of roads,drains, manhole, sumps, or where required by providing close graded Material, mixing in a mechanical mix plant at OMC(Optimum Moisture Content), carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete. |
| 13 | Providing and laying PLAIN CEMENT CONCRETE 1:2:4 (1- Cement : 2- Coarse sand : 4- gradedstone aggregates 20 mm nominal size) in foundations and superstructure including, machine mixing, leveling compacting, curing and formwork if any, scaffolding, stagingetc. complete as directed and instructed by Engineer-in-Charge. Volume of PCC laid to be measured for payment. |
| 14 | Providing material and labour for laying machine mixed/machine batched/RMC controlled cement concrete M.250 using graded black trap stone aggregates of maximum 20mm nominal (down graded) size including fine aggregate confirming to IS 383 with minimum cement content as per IS456 (without flyash) for durability shall be followed as per approved design mix & latest IS456 for reinforced cement conrete work for all elements,all floors,all heights/depths, any lead and lift including cost of formwork with sheathing steel or form finish ply shuttering , scaffolding, staging, vibrating, compacting, finishing andcuring complete but excluding cost of reinforcement for reinforced concrete work in Foundations,footings, Baseof columnsandMass concrete, as directions of Engineer in charge Complete.Preliminary cubes to be prepared on award of work and to be tested to meet the specified requirement for M25 mix, design mix to be approved by the Engineer-in-charge/Architect. Concrete placing shall be done with utmost care, the free drop height shall not exceed 1.5m, and concrete shall be vibrated with immersion type vibrators having frequency not less than 7000 vibrations per second in methodical method so as all points of structures are covered. Free concrete surface shall be covered with Hessian cloth and kept wet. |
| 15 | Providing material and labour for laying machine mixed/machine batched/RMC controlled cement concrete M.250 using graded black trap stone aggregates of maximum 20mm nominal (down graded) size including fine aggregate confirming to IS 383 with minimum cement content as per IS456 (without flyash) for durability shall be followed as per approved design mix & latest IS456 for reinforced cement conrete work for all elements,all floors,all heights/depths, any lead and lift including cost of formwork with sheathing steel or form finish ply shuttering, scaffolding, staging, vibrating, compacting, finishing andcuring complete but excluding cost of reinforcement for reinforced concrete work in Columns, Pillars posts and struts etc complete as directed by Engineer-incharge. Preliminary cubes to be prepared on award of work and to be tested to meet the specified requirement for M25 mix, design mix to be approved by the Engineer-in-charge/Architect. Concrete placing shall be done with utmost care, the free drop height shall not exceed 1.5m, and concrete shall be vibrated with immersion type vibrators having frequency not less than 7000 vibrations per second in methodical method so as all points of structures are covered. Free concrete surface shall be covered with Hessian cloth and kept wet. |
| 16 | Providing material and labour for laying machine mixed/machine batched/RMC controlled cement concrete M.250 using graded black trap stone aggregates of maximum 20mm nominal (down graded) size including fine aggregate confirming to IS 383 with minimum cement content as per IS456 (without flyash) for durability shall be followed as per approved design mix & latest IS456 for reinforced cement conrete work for all elements,all floors,all heights/depths, any lead and lift including cost of formwork with sheathing steel or form finish ply shuttering , scaffolding, staging, vibrating, compacting, finishing andcuring complete but excluding cost of reinforcement for reinforced concrete work in Lintels,Beams, Girders and Cantilever etc complete as directed by Engineer-incharge.Preliminary cubes to be prepared on award of work and to be tested to meet the specified requirement for M25 mix, design mix to be approved by the Engineer-in-charge/Architect. Concrete placing shall be done with utmost care, the free drop height shall not exceed 1.5m, and concrete shall be vibrated with immersion type vibrators having frequency not less than 7000 vibrations per second in methodical method so as all points of structures are covered. Free concrete surface shall be covered with Hessian cloth and kept wet. |
| 17 | Providing material and labour for laying machine mixed/machine batched/RMC controlled cement concrete M.200 using graded black trap stone aggregates of maximum 20mm nominal (down graded) size including fine aggregate confirming to IS 383 with minimum cement content as per IS456 (without flyash) for durability shall be followed as per approved design mix & latest IS456 for reinforced cement conrete work for all elements,all floors,all heights/depths, any lead and lift including cost of formwork with sheathing steelor form finish ply shuttering, scaffolding, staging, vibrating, compacting, finishing andcuring complete but excluding cost of reinforcement for reinforced concrete work in Slabs, landing, shelves andCantilever etc complete as directed by engineer-incharge.Preliminary cubes to be prepared on award of work and to be tested to meet the specified requirement for M20 mix, design mix to be approved by the Engineer-in-charge/Architect. Concrete placing shall be done with utmost care, the free drop height shall not exceed 1.5m, and concrete shall be vibrated with immersion type vibrators having frequency not less than 7000 vibrations per second in methodical method so as all points of structures are covered. Free concrete surface shall be covered with Hessian cloth and kept wet. |
| 18 | Providing material and labour for laying machine mixed/machine batched/RMC controlled cement concrete M.250 using graded black trap stone aggregates of maximum 20mm nominal (down graded) size including fine aggregate confirming to IS 383 with minimum cement content as per IS456 (without flyash) for durability shall be followed as per approved design mix & latest IS456 for reinforced cement conrete work for all elements,all floors,all heights/depths, any lead and lift including cost of formwork with sheathing steelor form finish ply shuttering , scaffolding, staging, vibrating, compacting, finishing andcuring complete but excluding cost of reinforcement for reinforced concrete work in Slabs, landing, shelves and Cantilever etc complete as directed by Engineer-incharge.Preliminary cubes to be prepared on award of work and to be tested to meet the specified requirement for M25 mix, design mix to be approved by the Engineer-in-charge/Architect. Concrete placing shall be done with utmost care, the free drop height shall not exceed 1.5m, and concrete shall be vibrated with immersion type vibrators having frequency not less than 7000 vibrations per second in methodical method so as all points of structures are covered. Free concrete surface shall be covered with Hessian cloth and kept wet. |
| 19 | Providing material and labour for laying machine mixed/machine batched/RMC controlled cement concrete M.250 using graded black trap stone aggregates of maximum 20mm nominal (down graded) size including fine aggregate confirming to IS 383 with minimum cement content as per IS456 (without flyash) for durability shall be followed as per approved design mix & latest IS456 for reinforced cement conrete work for all elements,all floors,all heights/depths, any lead and lift including cost of formwork with sheathing steelor form finish ply shuttering, scaffolding, staging, vibrating, compacting, finishing andcuring complete but excluding cost of reinforcement for reinforced concrete work in WALLS from top foundation level to all levelsetc complete as directed by Engineer-incharge.Preliminary cubes to be prepared on award of work and to be tested to meet the specified requirement for M25 mix, design mix to be approved by the Engineer-in-charge/Architect. Concrete placing shall be done with utmost care, the free drop height shall not exceed 1.5m, and concrete shall be vibrated with immersion type vibrators having frequency not less than 7000 vibrations per second in methodical method so as all points of structures are covered. Free concrete surface shall be covered with Hessian cloth and kept wet. |
| 20 | Providing and executing the work for M-25 Grade trimix concrete floor including finishing and curing of R. C. slabs/floor/road of any thickness or plain cement concrete of any thickness using VACUUM DEWATERING systemin a way as specified by the manufacturer of equipment in alternate panels of size specified in dwg, & power toweling the same to achieve the finish specified in the drawing. Adequate precaution to be taken to ensure that groove cutting, 6mm wide x 25mm deep, is taken up as per schedule after completion of finishing, in case if groove cutting not taken up as per schedule, entire finish floor may be qualified for rejection & may have to be re-done, dismantling finished concrete at no cost to client. Volume of concrete poured to be measured for payment. Cost shall also include Providing hard topping on flooring with Nitoflor of Fosroc or Master Top 200 of BASF or approved equivalent make at 5kg/M2 on surface, tremix flooring & cost shall also include goorve cutting and filling withpolysulphide sealent for flooring/Bitumious for road filling material, etc.Providing & fixing MS roundbar as dowels in CONCRETE FLOOR for EXPANSION JOINTS with over size PVC sleeve & cap filled with rock wool as per drawings and details- asper IS 2062, etc completed as per the direction of engineer-in-charge.200MM thickness to be considered for quotating rate |
| 21 | Providing and executing the work for M-35 Grade trimix concrete road including finishing and curing of R. C. slabs/floor/road of any thickness or plain cement concrete of any thickness using VACUUM DEWATERING systemin a way as specified by the manufacturer of equipment in alternate panels of size specified in dwg, & power toweling the same to achieve the finish specified in the drawing. Adequate precaution to be taken to ensure that groove cutting, 6mm wide x 25mm deep, is taken up as per schedule after completion of finishing, in case if groove cutting not taken up as per schedule, entire finish floor may be qualified for rejection & may have to be re-done, dismantling finished concrete at no cost to client. Volume of concrete poured to be measured for payment. Cost shall also include Providing hard topping on flooring with Nitoflor of Fosroc or Master Top 200 of BASF or approved equivalent make at 5kg/M2 on surface, tremix flooring & cost shall also include goorve cutting and filling with polysulphide sealent for flooring/Bitumious for road filling material, etc.Providing & fixing MS roundbar as dowels in CONCRETE FLOOR for EXPANSION JOINTS with over size PVC sleeve & cap filled with rock wool as per drawings and details- asper IS 2062, etc completed as per the direction of engineer-in-charge.200MM thickness to be considered for quotating rate |
| 22 | Providing, laying and fixing in position REINFORCEMENT High yield deformed bars/TMT/ FE500/FE500D/FE550 forR.C.C. works at all levels including cutting, bending and binding with 16 gauge M.S. annealed wire, providing cover blocks of C.M. 1:2 Embedded with binding wire etc. complete. The reinforcement detailing to IS 456 or, if specified by engineer, shallconformto IS: 13920 (Ductile detailing of R. C. Structures),bars as per IS 1786 the rate shall be inclusive of executing such detailing. Laps to be measured shall be as shown in drawing and for reinforcement length longer than available in market. Chairs, pinsand laps other than that specified shall not on be measured and paid for. No extra to be paid for height, rate remains same at all levels, complete as per drawings, specification, direction ofengineer-incharge. Make: TATA, SAIL, JSW or as approved byengineer-in-charge Complete. |
| 23 | Providing fusion bonded Epoxy coating not less than 175 micron thickness and up to 300 micron to reinforcement bars as per IS- 13620-1993/ASTM-775 M including testing of coating at plant and all taxes as directions of chief engineer in charge Complete. (A) 8mm to 32mm dia bar |
| 24 | Brick work using common burnt clay building bricks including scaffolding, raking of joints, curing using first class bricks having min. comp. Strength 35 kg/cm2 of approved manufacturer in foundation and plinth in Cement Mortar 1:6 (1- Cement : 6 -fine sand)(B)ConventionalAll bricks and shallbe soaked in waterfor at least 24 hours before use.bricks used for masonry work shall be as available locally, but approvedbefore start of work. volume of masonry to be measured for payment. |
| 25 | Providing & fixing LIGHT WEIGHT MASONRY BLOCKS of- Sand Based Autoclaved Aerated Concrete blocks (AAC Blocks) of any thickness using Epoxy based jointing adhesiveof approved make, upto all floor level/all heights, masonry walls in jointing mortar, complete as per Technical specification, density of blocks shall not exceed 700 kg/cum, using bonding material supplied by the manufacturer as per their instructions, including necessary scaffolding for fixing, in line & level. Volumne of blocks erected to be measured for payment. R.C.C. coping of size-wall thickness x 100mmht. at 0.91m intervals shall be provided including reinforced with 2 Numbers 6mm diameter horizontalbars and8mm diameterat 200 c/cties. R.C work not to be measured separately but included in rate.other specifications as directions of Engineer in Charge Complete |
| 26 | Providing and laying 10mm thick in single coat CEMENT PLASTER in (i)Cement mortar 1:3 (1-cement:3-sand) at all height/all floors to internal surfaces of all elements, walls, R.C.C. work, Ceiling,[backing coat at places where glazed or ceramic tiles are to be fixed etc]. including hacking of concrete surfaces, racking of joints, scaffolding, curing, providing chicken mesh at all necessary joints, etc. complete. Final finished surface shall be little rough , so it has proper bonding to paint putty.The surfaces to be plastered to be hacked immediately on de-shuttering. The Brick/ RCC surface to be plastered to be cured sufficiently before start of plaster. Initial bare surface area to be Plastered shall be measured for payment unless noted otherwise, etc as directions of Engineer in charge Complete. |
| 27 | Providing and laying 20mm thick SANDFACED CEMENT PLASTER of required grain finishing upto all height/all floors includinggrooves,pattas etc. in two coats having the the base coat of not less than 12 mm thickness in CM 1:3 (1-cement : 3-sand) & finished coat 8 mm thk, in CM 1:1 (1-cement : 1-sand) to external surfaces of concrete & masonry including hacking of concrete surfaces, racking of joints, scaffolding, curing, providing chicken mesh at all necessary joints, etc. complete. Rate shall include addition of “Impermo” water proofing compound or equivalent as approved by engineer-in-charge, providing, adding & mixingoffine fibrillated 100% virgin polypropylene fibers in cement mortar to formhomogeneous mixture @125 gms per a bag of cement in both the coats of plaster, 12mm long fibers shall be used in first coat & 6mm long fibers shall be used in second finished coat. providing drip mould 40mm wide and 12mm thick in cement mortar 1:3 on soffit of chajjas, canopies, gutters etc.complete. as directions of Engineer in charge Complete.The surfaces to be plastered to be hacked immediately on de-shuttering. The Brick/ RCC surface to be plastered to be cured sufficiently before start of plaster. Initial bare surface area to be Plastered shall be measured for payment unless noted otherwise, etc as directions of Engineer in charge Complete. |
| 28 | Providing and applying PU (Polyurethane) based liquid applied waterproofing treatment to terraces/toilets/wet areas including supply of approved materials, surface preparation, crack filling, priming, reinforcement, membrane application, flood testing and warranty complete.Providing and applying PU based liquid elastomeric waterproofing system comprising surface preparation, cleaning, repairing cracks and honeycombs using PU sealant/polymer modified mortar, forming fillet at junctions, applying approved PU compatible primer, reinforcement with polyester/glass fibre mesh at all corners, junctions, pipe inserts and critical areas, followed by application of PU liquid membrane in two or more coats to achieve minimum dry film thickness of 1.5 mm for terraces and 1.0 mm for toilets/wet areas including extending coating up to minimum 300 mm on vertical faces. For terrace application, finishing shall include a UV-resistant aliphatic PU/reflective elastomeric top coat, and for toilets/wet areas, tiling or protection screed shall be done only after curing. Work shall include flood test for minimum 48 hours before finishing. Complete work shall be carried out as per manufacturer’s specifications and directions of Engineer-in-Charge, using approved products (Sika/Fosroc/BASF/Dr. Fixit/Asian Paints or equivalent) and by authorized applicator only. Contractor shall provide a 10-year leakproof performance warranty on stamp paper jointly signed by manufacturer and applicator.Rate shall be inclusive of all material, labour, cleaning, primer, membrane, reinforcement, UV protection coat, tools and plants, curing, testing, and cost of 10-year warranty complete.Make:- MYK Arment, Pidilite, Sika or equivelant. |
| 29 | Providing material, Labour and equipments for Providing and laying integral Cement based water proofing treatment with brickbat including preparation of surface as required for treatment of roofs, balconies, terraces etc. consisting of following operations : a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer in charge over the RCC Slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. b) Laying brick bats with mortar using broken bricks / brick bats 25mm to 115mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer in charge over 20mm thick layer of cement mortar of mix 1:5 ( 1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer in charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junction of walls and slabs. c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg / sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer in charge.d) Finishing the surface with 20mm thick jointless cement mortar of mix 1:4 ( 1 cement : 4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer in charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300 x 300 mm square 3 mm deep.e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.All above operations to be done in order and as directedand specified by the Engineer in charge : Including Khurra & Gola work with average thickness of 120mm and minimum thickness at Khurra as 65 mm etc. complete as directed by Engineer in charge. |
| 30 | ALUMINIUM WORKS- Providing material and labour for fixing in position frames, shutter for any type of aluminium work for any type of door, window, partition, made out of any type of aluminium sections of approved make having minimum 50 micron pure polyester powder coating of approved shade, texture & colour of approved make for all floors, all levels, all heights, all shapes, all sizes including cutting, bending, crimping, fabricating in best workmanship manner etc as per the drawing, specification and as directed by Architect or Engineer-in-Charge. Contractor shall prepare shop drawing based on concept drawing and get approved from the consultants before procurement of material. All loose material shall be approved. Mockup of one/two window shall be executed as per approved shop drawing with all hardware. Work shall carried out as per the approved shop drawings, approved mock-up and approved sample. Actual weight of installed Aluminium sections (for using fabrication without considering any wastage) shall only be measured and shall be considered for the payment. Glazing shall be paid as seperate item. Contractor shall provide guarantee for stability, water tightness etc for 12 months after defects liability period. Rate shall be inclusive of providing aluminium sections, cutting, fabrication, errection and fixing to the best workmanship manner, including1) Sheet metal screws and casted solid aluminum corner cleats fixed with external byttins with a spring for rapid and secure joint assembly for casement and sliding shutter and frame;2) Glazing clips for receiving infill panel; 3) Best quality wool pile where ever shutter touches the frame and compatible microwave cured EPDM rubber; 4) Dash Anchor fasteners of HILTI HRDUGT or equivalent for fixing the frame assembly to the RCC or masonry surfaces. Minimum 1 anchor fastener shall be used for every 600 mm length of section for stability of frame. 5) 10mm GI tie rod for connecting vertical stile at top and bottom for aluminum door shutter and 4mm thick solid aluminium corner cleat of full thickness of sectionfor connecting style and horizontal rails; 6) providing and fixing packing (rough ground) in full periphery/ at every 600mm c/c with average 6 mm thick PVC spacer/ compact sheet of width (equal to section width less 30mm for backer rod and sealant); 7) Filling the gap between wall and frame on both sides (outside and inside) with polyethylene baker rod of avg. 10 mm thickness of approved make and color and then sealing the remaining gap with neutral grade G/M (Glazed & Metal) weather silicon sealant of approved make and color. 8) Termite treated seasoned teak wood as infill material to installe hardware in door shutter and frame as and when required, etc as per directions of Engineer in charge Complete. Make:- Cardinal series, Jindal or equivalent as approved by chief engineer |
| 31 | Providing & Fixing Louvers and Fins (made out of Aluminium Section)Providing, fixing, designing aluminium fixed louver of any type of louver section of approved make having minimum 50 micron polyster powder coating on all the surfaces of approved shade, texture & make as per manufacturer\"s specifications. Contractor shall submit the shop drawing for louver/ fins based on concept design/ drawing and as per elevation. Aluminium louver section shall be fixed on aluminium framing/ carrier/ panel/ GI clip and necessary sub structure with required fastners, hardware as per approved shop drawing etc complete for all floor, all height including scaffolding as directed by engineer in charge.Louver, framing and sub structure shall be in proper line, level and plumb. Necessary MS work shall be paid in relevant tender item. |
| 32 | Providing material and labor for Structural steel work (Confirming to IS 4923-1997) riveted, bolted or welded in builtup, conventional, Hollow section, etc for all type sections, in framed work, railing work, any type of fabrication work, including cutting, hoisting, fixing in position and applying a priming coat &two coat applying synthetic enamel paint of approved steel primer all complete as per the structural designs and as directions ofEngineer- in -Charge Complete. |
| 33 | Providing and fixing in position Stainless steelRailing, The railing is made of stainless steel AISI 304 with a polished finish. Glass: The glass used for the railing should be toughened glass with a thickness of 10mm. The glass will frosted as approved by architect.The height of the railing is 36 inches (914mm).Baluster spacing: The spacing should meet safety standards.Handrail: It should be at least 1.5 inches (38mm) in diameter made of stainless steel materials.Anchors: The railing is anchored to the floor or the side of the staircase using stainless steel anchors. for quotation consider Stainless steel consumption of 9 kg per Running meter, Railing height 1.0 Mtr, Toughned glass consuption 1 sqm per running meter. |
| 34 | Providing, fabricating, supplying and fixing Mild Steel (MS) grill for windows, complete with all materials, labour, welding, cutting, grinding, painting and installation as per drawings and instructions.The grill shall be made using mild steel sections such as flats, round bars, square bars or hollow sections. The steel used shall conform to IS 2062 Grade A or IS 1079.The grill shall be fabricated exactly as per approved architectural drawings. All joints shall be fully welded and ground smooth. Suitable MS lugs or holding brackets of minimum 12 mm thickness and 25 mm width shall be provided for fixing into the wall or window frame. Fixing shall be done with grouted bolts, anchor fasteners, or holdfasts in PCC or non-shrink grout. Welding directly to aluminium frames shall not be permitted, and only bolted connections with washers shall be allowed when grills are fixed to aluminium windows.The design must allow smooth operation of window shutters and proper cleaning without obstruction.All steel surfaces shall be cleaned properly to remove rust, oil, dust and mill scale. After cleaning, one coat of zinc chromate red oxide primer conforming to IS 2074 shall be applied. Two coats of synthetic enamel paint of approved shade conforming to IS 2932 shall then be applied. The total finished paint thickness shall be adequate to protect the steel from corrosion.The rate shall be inclusive of all materials, wastage, labour, fabrication, brackets, fasteners, grinding, primer, paint, equipment, scaffolding and transportation, and nothing extra shall be paid for these works, complete as directed by engineer-in-charge |
| 35 | Supply, installation, testing and commissioning of a complete Sliding Motorized Gate Automation System consisting of a heavy-duty sliding gate operator (230V AC, electromechanical, IP55-rated, thermal overload protected) suitable for sliding gate weight up to 1200 kg, equipped with a microprocessor-based control panel featuring soft-start/soft-stop, adjustable opening/closing speed, programmable auto-close timer, obstruction auto-reverse, magnetic/mechanical limit switches, and manual release mechanism for emergency operation. System shall include high-strength galvanized steel/nylon gear racks, heavy-duty base plate and mounting hardware, infrared photocell safety sensors, LED flashing warning lamp with antenna, remote controls (minimum 2 nos., rolling-code type), external push-button station, emergency stop switch, surge protection device, cable trays/conduits, complete power and control wiring, weatherproof junction boxes, proper earthing, and all civil, alignment, testing, adjusting, and commissioning works necessary to deliver a fully functional, safe, and reliable automatic sliding gate system. Rate is to be provided only for providing automation system. Gate measurement and weight to be paid in relevent tender item and not to be included in this cost. |
| 36 | Providing and fixing factory-made PVC laminated door shutter, 30 mm thick, made of engineered core panel construction, manufactured as per IS: 4020. The shutter shall consist of a rigid framework with stiles and rails of treated engineered wood, bonded with waterproof synthetic resin adhesive conforming to IS: 848. The infill core shall be solid composite block board as per IS: 1659. The shutter faces shall be factory-laminated with 1.0 mm ± 0.1 mm thick PVC foil/laminate sheet, thermo-compressed and bonded uniformly on both sides using hot‐melt adhesive technology. The laminate finish shall be smooth, waterproof, termite and borer resistant, and shall include decorative wood-grain/plain texture. All exposed edges, cut-outs and joint edges shall be sealed with matching PVC edge beading and welded/sealed using heat-press or solvent-bonding to ensure moisture proofing.Shutter shall be supplied with provision for locking arrangement, hinges, and hardware fixing, including required solid backing/packing inside stiles and lock rail, ensuring adequate screw holding strength. The complete shutter shall meet physical strength/performance criteria mentioned in IS: 4020 for impact, deflection, squareness, water resistance and adhesion tests.Rate shall include: complete factory-manufactured door shutter with PVC laminate, inner core construction, sealing of edges, provision for hardware, delivery at site and installation including adhesive, nails/screws, etc.Note: Door frame and architectural hardware (hinges, tower bolt, lock, handles, door stopper, etc.) shall be paid separately under respective item |
| 37 | Providing and fixing 8mm thick clear toughened glass for doors, windows, partitions, glazing, full-height panels, or similar work, including all labour, materials, fixing accessories and scaffolding, complete as directed by the Engineer-in-Charge.The glass shall be 8mm thick clear float glass, heat-treated through a controlled toughening process, achieving a minimum strength of 4 to 5 times that of normal float glass. The toughened glass shall comply with IS 2553 (Part 1): Safety Glass for Architectural Use and IS 14900 (Safety Glass and Glazing System). Glass edges shall be machine-polished, smooth and free from sharpness. No chipped edges, waves, bubbles, or optical distortion shall be accepted.Glass shall be toughened at an approved factory with heat soak test wherever specified. Each piece used at site must bear the manufacturer’s permanent marking/stamp, ensuring identification of grade and make.The glass shall be installed using approved stainless-steel patch fittings, U-channel, glazing clips, EPDM rubber gaskets, aluminium channels, hinges, or spider fittings as applicable. All fixing accessories shall be non-corrosive, made of SS 304 grade minimum. For framed systems, fixing shall be with EPDM gaskets and neutral-cure silicone sealant, ensuring air-tight and water-tight joints.For door systems, suitable floor spring, door handle, lock, pivot, top patch, bottom patch and stopper shall be installed as per design. Any hardware specified separately shall be paid under respective items.Work includes cutting, edge finishing, toughening, handling, transportation, lifting, installation and cleaning. Any breakage during transportation or fixing shall be replaced by the contractor at no extra cost.Measurement shall be taken in square metres (m²) of actual installed glass area in position. Hardware, frame sections, door fittings and supports shall be measured and paid separately, wherever applicable.Approved makes for glass are Saint-Gobain, Asahi India (AIS), Pilkington, Guardian, Modi Guard, or any equivalent make approved by the Engineer-in-Charge. |
| 38 | Providing, fabricating, supplying and installing Structural Curtain Wall Glazing System comprising aluminum mullions and transoms, reflective glass panels, structural sealant, weather barrier, hardware, and accessories, complete in all respects, including design & engineering, performance testing, fabrication, erection, and finishing works. Work shall include the following:1. Aluminum FrameworkExtruded aluminum sections of alloy 6063-T5/T6, with minimum thickness of:Mullions & transoms: 3.0 mm.Finish:Powder coated (minimum 80 microns)The framework shall be designed for:Wind load resistance as per IS 875 (Part 3)Minimum safety factor 2.0Maximum deflection: Span/175 or 25 mm, whichever is less.2. Glass PanelsType: Reflective toughened glassMinimum thickness:Single reflective toughened glazing: 8 mmGlass shall conform to IS 2553 Part 1.Edge treatment:Smooth ground edges for structural bonding.3. Structural Sealant and Weather SealantsStructural silicone: Dow Corning / GE / Sika / 3M or equivalent approved.Weather sealant: UV-resistant, non-staining silicone.Sealant thickness and toe size as per manufacturer’s specifications.Primer and backer rod (closed cell) to be used as required.Manufacturer’s certification for compatibility and warranty must be provided.4. Gaskets, Thermal Breaks & InsulationEPDM / Neoprene gaskets with corner vulcanization at all joints.Thermal break system (where specified) with polyamide strips.Insulation foam backing for perimeter.5. Anchorage SystemSS anchor fasteners: Grade 304 with chemical anchoring where required.SS brackets of adequate section as per structural design.All brackets to be shop fabricated with corrosion protection6. AccessoriesIncludes cleats, screws, pressure plates, cover caps, internal trims, flashing, drip edge, and sealant fillet finishes.All screws, nuts, bolts should be SS Grade 304.7. Water & Air TightnessWater tightness to be achieved through two-stage sealing.Pressure equalization system where required.System must comply with:ASTM E 331 (Water Penetration)ASTM E 283 (Air Leakage)8. Testing Requirements Design calculations and shop drawings should be submitted and approved.Mock-up sample to be fabricated on site for approval.On-site water spray test to be conducted.Manufacturer/product warranty certificate for sealants and system.9. InstallationAll installation shall be in true line, level & plumb, using laser alignment.Complete cleaning, protection and handing over after installation.Scaffolding/staging and safety protection is included in the quoted rate.Work executed as per NBC, IS 875, IS 2553, and manufacturer guidelines.10. MeasurementMeasurement shall be taken in Sqm of actual visible glazing area, including mullions, transoms, gaskets, sealants, brackets, and all related materials & accessories.11. Rate to includeDesign & engineeringTesting and mock-upSupply of all componentsFabrication, installation, and cleaningWastage, scaffolding, and safety worksNo extra payment for wastage, scaffolding, or hardware. |
| 39 | Providing, fabricating, supplying and installing ACP Cladding with closed-joint / open-joint system including framing, panels, weather barrier, sealants, fasteners, complete with shop drawings, structural supports, installation, and finishing as per drawings and architect\"s instructions.1. ACP PanelThickness:4 mm Composition:0.50 mm thick Aluminum alloy 3003 both sidesCore: Mineral Core FR Grade (Class A)Finish type (as specified):PVDF Exterior Coating (minimum 2 coats, 28–32 microns)Color/texture as approved.ACP brand: Aludecor / Alucobond / Alstrong / Viva / Eurobond or approved equivalent.Fire Retardant Panels must comply with:ASTM E84EN 13501-1 (Class A)2. Framework / SubstructureFramework of extruded aluminum sections (6063-T5).Minimum thickness:Aluminum 2.5 mmFraming with required cleats, brackets, expansion joints, and structural supports including corrosion protection.3. Fixing / AnchorageMechanical fixing using:SS screws (Grade 304)Aluminium/SS cleats, nuts & boltsConcealed mechanical system with rivets / Z brackets allowing thermal expansion.Anchorage to RCC/civil surface using:SS anchor fasteners (S S 304)Chemical anchors where required.4. Panel Fabrication & JointsCut and routed using CNC or panel routing machine only. Hand cutting is not permitted.Closed joint OR open joint system (as specified):Closed joint filled with UV-resistant silicone sealantOpen joint (8–12 mm) with baffle profiles / back weather sealExpansion joints to be provided horizontally and vertically as required.Joints to be uniform, straight, and aligned with architectural grid.5. Sealants, Gaskets & FlashingsUV-resistant silicone: Dow Corning / GE / Sika / 3MBacker rod: closed-cell polyethylene.Flashings, corner trims, drip edges in aluminum with same finish/colour.6. Surface PreparationRCC surface to be cleaned, brushed, and made dust free.Anti-corrosion coating for MS framework (if used), with:2 coats of zinc chromate primer + enamel paint, orHot dip galvanized (min. 80–120 microns)7. Alignment & InstallationAll installation to be true to line, level, plumb & grid using laser alignment.Ensure ventilation gap behind ACP where required.Water/drainage provision at sill/ledge/coping areas.8. Testing & SubmittalsSubmit:Shop drawingsStructural stability certificate for framingColour/finish sample approvalWarranty certificates:10years warranty for PVDF coatingManufacturer warranty for FR ACP 9. MeasurementMeasurement to be taken in Sqm of actual cladding covering visible finished area, including corners, folds, returns, grooves, flashings, cleats, supports, and consumables.10. Rate to IncludeACP sheet cost, fabrication, cutting and routingSubframe, fasteners, anchors, screwsSealants, backer rods, labour, scaffoldingWastage, finishing, cleaning, transportation |
| 40 | Providing and Fixing 15 mm Thick Full Body Heavy Duty Vitrified Tiles for Platforms, Counters, Frames, Staircase and Similar Locations with work includes providing and fixing full body heavy duty vitrified tiles of 15 mm thickness in platforms, kitchen counters, vanity counters, door and window frames, sills, jambs, risers, treads, staircase soffits, fascias and all similar vertical or horizontal locations. Tiles shall conform to IS:15622, be full body (through-colour), non-porous, scratch-resistant and suitable for heavy impact and high wear locations. Tiles shall be of approved shade, size, texture, edge profile and finish (matt/stone/anti-skid/polished), as directed by the Engineer-in-Charge. Full body tiles shall have water absorption less than 0.08%, high breaking strength and high abrasion resistance suitable for service areas and exposed edges.Tiles shall be factory cut with straight edges, uniform thickness and free from warping, cracks, chips, stains, cavities or manufacturing defects. Where exposed edges occur (on counters, sills, steps, jambs, fascia), the tiles shall be edge-polished/chamfered or rounded as required to give a finished appearance. The colour shall be homogeneous through the thickness to allow exposed finishes without additional edge treatment material.Tiles shall be fixed with polymer-modified stone/vitrified tile adhesive or epoxy adhesive of approved make as per manufacturer’s instructions. Back-buttering with adhesive shall be mandatory to ensure 100% bond and avoid hollowness. The surface to receive tile shall be cleaned, levelled, made dust-free and primed using bonding agent/primer wherever specified. Clamping or temporary support shall be provided for vertical or inclined faces until adhesive sets. Mortar bedding shall not be used unless specifically approved.Joints shall be uniform and grouted with epoxy grout or matching coloured grout depending on the location. In wet areas, countertops or kitchen backsplashes, epoxy grout is mandatory. Exposed edges and joints shall be finished neat and smooth without sharp projections. Water drip moulds/grooves shall be formed on counter edges, window sills and external projections where required.The contractor shall provide samples for approval of type, finish and shade prior to procurement. Only the approved batch shall be used. Tiles with chips, edge defects or surface scratches after fixing shall be replaced at contractor’s cost. All polishing of edges, profiling, drilling, cutting for fixtures, tap holes, sink cut-outs, washbasin/counter fittings, railing supports and similar works shall be included in the rate.The quoted rate shall include cost of tiles, adhesive, primer, grouting (cement/epoxy), cutting, polishing of exposed edges, rounding/chamfering, holes/cutouts, grooves, scaffolding, curing, cleaning, edge finishing, transportation, loading/unloading, labour and all incidental works. Make: Somany, Kajaria, simpolo or equivalent as approved by engineeri-in-charge or Architect |
| 41 | Providing material & labour forGranite stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. Granite Stone of approved shade. FOR URINAL PARTITIONS |
| 42 | Providing material and labour for making Black Granite stone Counter Wash Basin of 0.60mt wide with vertical & Horizontal Support of granite stone and having bottom slab of 25mm to 30mm thick kadappa stone fixing with cement motar 1:4 (1 Cement :4fine sand) and neat cement slurry as per requirement including cutting the granite stone & providing7 fixing oval shape wash basin of 22\"\"x16\" size white colour in line & level. All exposed Edges of granite should be moulded including all accessories like pillar cock (Swan neck type), fexible inlet pipe 15mm dia, C.P. brass waste coupling 32mm, PVC Waste pipe 32mm etc. as directed by Enginner on Charge. |
| 43 | Providing and fixing vitrified tiles of size 600×600 mm and 10 mm thick in dado, on walls, pillars or vertical surfaces, of approved make, shade, colour, pattern and finish, conforming to IS: 15622 (Vitrified Ceramic Tiles). The tiles shall be of first quality, free from cracks, edge chipping, warpage, stains, manufacturing defects and shall have water absorption less than 0.08%. Finish may be glossy, matt, nano-polished, stone finish or as directed by the Engineer-in-Charge.The wall surface shall be cleaned thoroughly and made free from dust, efflorescence, oil or loose particles. The surface shall be prepared by applying a slurry coat of cement mixed with bonding latex or approved tile adhesive primer to ensure proper bond. Tiles shall be fixed on an even surface using polymer-modified tile adhesive of approved quality, applied as per manufacturer’s instructions to achieve full bedding without voids. The use of cement mortar for vertical tile fixing shall be avoided unless specifically permitted.Tiles shall be pressed firmly so as to achieve proper bond. Plastic spacers shall be used where recommended. After setting, tile joints shall be grouted with white or coloured cement matching tile shade. Grouting must be completed after the adhesive has fully set. Care shall be taken to avoid staining or scratching the surface. Excess grout or adhesive shall be removed using a wet sponge immediately after application. Final cleaning shall be done using mild detergent without damaging the tile surface.The contractor shall submit samples of the tile for approval prior to purchase. Only one approved shade and batch shall be used throughout the work. Tiles shall be cut precisely using a tile cutter to fit around switches, fixtures or obstructions, ensuring clean edges. Vertical alignment, level and pattern continuity with adjacent floors or dado must be maintained.Measurement shall be in square metre of finished work. The quoted rate shall include cost of tiles, adhesive, primer, spacers, grouting materials, cutting, labour charges, scaffolding, curing where required, cleaning, transportation, loading, unloading and all accessories necessary to complete the work. Make: Nitco, Simpolo, Kajaria or equivelant as approved by Chief-engineer |
| 44 | Providing and Fixing Anti Skid Vitrified Floor Tiles (600×600mm, 10mm Thick) with work includes providing and fixing vitrified tiles of size 600×600 mm (2’×2’) and 10 mm thickness, of approved make, shade, pattern and finish, conforming to IS:15622 (Vitrified Ceramic Tiles).The tiles shall be non-slip/anti-skid type with textured or matt finish suitable for wet areas, utility spaces, ramps, balconies, terraces, toilets, corridors or areas exposed to spillage. The coefficient of friction shall meet slip-resistance requirements for floor use in wet areas as per standard practice. Tiles shall have water absorption less than 0.08%, uniform in colour, thickness and tone, and shall be free from cracks, bends, edge chips or surface defects. The type of finish such as double charge, nano polished, matt or anti-skid shall be as directed by the Engineer-in-Charge.Before fixing, the existing floor or base surface shall be cleaned properly and made free from dust, grease or loose material. Any unevenness on the surface shall be corrected by applying cement mortar in proportion 1:4 (1 cement: 4 coarse sand). In case the tiles are laid over cement concrete flooring, the surface shall be well roughened and washed before laying. Tiles fixed using 20 mm average thick cement mortar 1:4 or using approved polymer-modified tile adhesive. When laying over mortar, cement slurry shall be applied on the back of the tile at the rate of 3.3 kg per sqm to ensure proper bonding. If adhesive is used, tiles shall be fixed strictly as per manufacturer’s instructions to ensure full bedding support without voids.Tiles shall be laid in proper line and level, with joints kept uniform. After laying, tile joints shall be neatly grouted using white or coloured cement mixed with matching pigments. The surface shall be cleaned immediately after fixing to remove mortar stains, adhesive marks or grout residues. Upon completion of work, the entire flooring shall be cleaned with a soft detergent and maintained until curing is completed. Care shall be taken to avoid damage, cracking or chipping of tiles during execution.The contractor shall provide tile samples before procurement and only the approved sample shade and batch shall be used at site. The quantity shall be measured in square metre of finished work, and the rate quoted shall include the cost of tiles, adhesive or mortar, grouting material, cutting, wastage, labour charges, curing, cleaning, loading, unloading, transportation and all other incidental works required to complete the job in all respects.Make: Nitco, Simpolo, Kajaria, johnson, Rak or as approved byengineer-in-charge complete. |
| 45 | Providing and Fixing Vitrified Floor Tiles (600×600mm, 10mm Thick) with work includes providing and fixing vitrified tiles of size 600×600 mm and 10 mm thickness, of approved make, shade, pattern and finish, conforming to IS:15622 (Vitrified Ceramic Tiles). Tiles shall have water absorption less than 0.08%, uniform in colour, thickness and tone, and shall be free from cracks, bends, edge chips or surface defects. The type of finish such as double charge, nano polished, matt shall be as directed by the Engineer-in-Charge.Before fixing, the existing floor or base surface shall be cleaned properly and made free from dust, grease or loose material. Any unevenness on the surface shall be corrected by applying cement mortar in proportion 1:4 (1 cement: 4 coarse sand). In case the tiles are laid over cement concrete flooring, the surface shall be well roughened and washed before laying. Tiles fixed using 20 mm average thick cement mortar 1:4 or using approved polymer-modified tile adhesive. When laying over mortar, cement slurry shall be applied on the back of the tile at the rate of 3.3 kg per sqm to ensure proper bonding. If adhesive is used, tiles shall be fixed strictly as per manufacturer’s instructions to ensure full bedding support without voids.Tiles shall be laid in proper line and level, with joints kept uniform. After laying, tile joints shall be neatly grouted using white or coloured cement mixed with matching pigments. The surface shall be cleaned immediately after fixing to remove mortar stains, adhesive marks or grout residues. Upon completion of work, the entire flooring shall be cleaned with a soft detergent and maintained until curing is completed. Care shall be taken to avoid damage, cracking or chipping of tiles during execution.The contractor shall provide tile samples before procurement and only the approved sample shade and batch shall be used at site. The quantity shall be measured in square metre of finished work, and the rate quoted shall include the cost of tiles, adhesive or mortar, grouting material, cutting, wastage, labour charges, curing, cleaning, loading, unloading, transportation and all other incidental works required to complete the job in all respects.Make: Nitco, Simpolo, Kajaria, johnson, Rak or as approved byengineer-in-charge complete. |
| 46 | Providing material & labour for laying Vitrified tiles 8 to 10 mm thick , in required size for Skirting upto 100mm on 10mm thick cement plaster 1:3 (1-cement : 3-coarse sand) and jointed with white cement slurry including finised with flush pointing & cleaning the surface etc. complete. For SkirtingMake: Nitco, Simpolo, Kajaria,johnson, Rak oras approved byengineer-in-charge complete. |
| 47 | Providing and Applying Lustre Paint with work includes providing and applying lustre finish paint on internal wall surfaces in required shade, complete as directed by the Engineer-in-Charge. The material shall be oil-modified or synthetic enamel-based washable lustre paint, with smooth sheen finish. The paint shall conform to Indian Standards IS: 101 (for testing of paint) and IS: 2932 (for enamel paints) or equivalent specifications. The brand and shade shall be approved before execution.The surface shall be properly cleaned by removing loose paint, dust, dirt, grease, algae and foreign matter. All cracks, dents and surface irregularities shall be filled using approved wall putty or plaster of Paris to make the surface even and smooth. The finished surface shall be prepared by rubbing with sandpaper and cleaned.The work shall include applying one coat of approved primer suitable for lustre paint system. After the primer dries, the surface shall again be smoothened by rubbing with sandpaper. A synthetic enamel undercoat or base coat shall then be applied as per the manufacturer’s recommendation. Finally, two coats of approved quality lustre paint shall be applied uniformly using brush or roller to achieve a smooth, even, washable finish free from brush marks, patches or streaks. Additional coats, if required for uniformity, shall be carried out by the contractor at no extra cost.All materials, labour, scaffolding, tools, masking tapes and necessary protection to electrical fixtures, flooring, furniture, windows and adjoining surfaces shall be included in the rate. After completion, stains shall be cleaned and the area handed over in proper condition.Measurement shall be taken in square metres of finished painted surface. The rate shall be inclusive of entire work including cleaning, surface preparation, primer, putty, undercoat, lustre paint, labour and all incidentals required to complete the work..Make: Jotun,Asian Paints, Berger Paints, Dulux Paints or as approved by chief engineer. |
| 48 | Providing and Applying Distemper Paint with work includes providing and applying dry distemper or oil-bound distemper on internal wall surfaces, in required shade, complete as directed by the Engineer-in-Charge. The material shall be of approved brand and manufactured in accordance with relevant quality requirements. Only pre-approved shade and material shall be used.Before application, the surface must be thoroughly cleaned to remove dust, dirt, oil, grease, organic growth, loose particles, old flaking paint and any other foreign matter. All cracks, dents and surface undulations shall be repaired using approved wall putty or plaster of Paris, and the surface shall be made smooth using sandpaper. The surface shall be properly dried and cleaned before application.One coat of approved primer shall be applied over the prepared surface. Primer shall be alkali-resistant where needed and suitable for the distemper system used. After the primer completely dries, the surface shall be sanded again lightly to ensure an even and smooth finish.Two or more coats of approved quality distemper shall then be applied uniformly with brush or roller to obtain even shade and uniform finish. The material shall be mixed and diluted only as per manufacturer’s specifications. The coating shall be free from streaks, patches, brush marks, pinholes, or colour variation. Additional coats, if found necessary to achieve a uniform finish, shall be applied by the contractor at no extra cost.The work shall include providing all materials, labour, tools, scaffolding, masking and protection to flooring, furniture, windows, doors, switch plates and other fixtures to avoid stains or damage. Stains and splashes, if any, shall be cleaned immediately. After completion of work, the site shall be cleaned and handed over in proper condition.Measurement for payment shall be taken in square metres of the finished painted surface. The quoted rate shall be inclusive of cleaning, surface preparation, putty, primer, multiple coats of distemper, scaffolding, labour, tools and all required incidentals to deliver a complete job.Make: Jotun,Asian Paints, Berger Paints, Dulux Paints or as approved by chief engineer. |
| 49 | Providing material & labour for Internal Wall painting (two coats) with Luxury Emulsion of approved brand and manufacture including suitable primer coat on undecorated wall surface to give an even shade including throughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth. asdirected by engineer in charge complete. One component waterborne 100% pure acrylic interior eggshell emulsion that must offer protection against different varieties of bacteria and fungus. Paint should free of HCHO, APEO and have crack bridging property of min 0.9 mm with class 1 flame spread resistanceThe product shall have a Volume Solids of minimum 35%The product shall be independently tested and approved for properties alike resistance to bacterial and fungal species, crack tolerance and flame spread resistance.The coating shall contribute to satisfying the following credit(s): Indoor Environmental Quality (IEQ) under LEED® 2009 Environmental Quality (EQ) and Materials and Resources (MR) under LEED® v4This product shall have a VOC limit not more than 24 g/lit.The product can be like Asian paint Royale series or approved equivalents.Two Coats of above paint should be applied using conventional Roller / Airless spray at the site after application and drying of applied Putty-Primer. Formeasurement of painting items the area painted shall be considered without any multiplication factor for different kinds of surfaces painted. Rate shall be quoted accordingly. All painting items final finish shall be as per manufacturer\"sspecification as per acceptance of Engineerin charge /Architect. No extra payment shall be made for extra/over coat if required.The rate shall be inclusive of providing bamboo scaffoldingMake: Jotun,Asian Paints, Berger Paints, Dulux Paints or equivalent.Guidelines for application1. Surface Preparation - Inspection: Assess the wall surface for defects like cracks, moisture, or old paint layers. All imperfections must be fixed before starting the painting process. - Cleaning: Clean the wall to remove dust, grease, and loose particles. Use a mild detergent solution or a vacuum to ensure a clean surface. - Repair: Fill cracks, holes, and other imperfections with a suitable filler (e.g., putty or spackle). Sand the area smooth after drying. - Priming: Apply a suitable primer to the wall to ensure proper adhesion of the artistic paint. Choose a primer based on the wall material (e.g., masonry, drywall, plaster). Allow the primer to dry according to the manufacturer\"s instructions. 3. Application Process - Base Coat: - Apply a base coat of paint, using a roller for large areas and a brush for edges and corners. Choose a base color that complements the final artistic design. - Allow the base coat to dry completely - Artistic Painting: - As per details provided by architect, Plan the design by sketching it lightly on the wall with a pencil or chalk & get necessary approval from architect or engineer-in-charge. Post approval proceed for final application. 4. Finishing - Sealing (Optional): Apply a clear sealer or varnish over the artwork for added protection, a matte, satin, or gloss finish based on the desired effect.6. Quality Standards - Adhesion: Paint should adhere firmly to the wall without peeling or flaking. - Finish: The final surface should be even, free of brush marks, and match the intended artistic design. - Durability: The painted surface should withstand normal wear and cleaning without damage |
| 50 | Providing and Applying Acrylic Washable Emulsion Paint with work includes providing and applying acrylic washable interior emulsion paint on internal plastered wall surfaces, in required shade, complete as directed by the Engineer‐in‐Charge. The paint shall be of approved brand, having low VOC, anti‐fungal properties, washable and suitable for high-traffic areas such as schools, offices, hospitals, and institutional buildings. Shade shall be pre-approved before application.Before application, the surface shall be thoroughly cleaned to remove dust, dirt, grease, soot, laitance, algae, loose paint and any other foreign matter. Surface cracks, dents, pores and undulations shall be repaired with approved wall putty or plaster of Paris. The surface shall then be rubbed and smoothened by sandpapering to obtain an even and uniform surface. All loose dust shall be removed afterwards.One coat of approved primer compatible with acrylic washable emulsion system shall be applied after proper surface preparation. The primer must be allowed to dry fully before applying the next coat. After the primer dries, the surface shall again be lightly sanded wherever necessary to ensure smooth finish.Two or more coats of approved acrylic washable emulsion paint shall then be applied using brush or roller as per manufacturer’s recommended dilution. The coats shall be applied uniformly to achieve even colour shade and smooth matt, soft sheen or satin finish as specified. The finished work shall be free from streaks, chalking, patchiness, pinholes, loose particles or brush marks. Any additional coats required to achieve uniform shade and finish shall be done by the contractor at no extra cost.The rate quoted shall include cost of all materials, tools, primer, emulsion paint, putty, labour, scaffolding and necessary protective covering to furniture, fixtures, floors, windows, switchboards and adjacent surfaces. Any stains, splashes or paint marks shall be cleaned immediately and the area shall be handed over in neat condition after completion of work.Measurement shall be made in square metres of the finished painted surface. The rate shall include complete work including cleaning, surface preparation, primer, putty, and applying multiple coats of acrylic washable emulsion paint with all incidentals to complete the job as directed.The rate shall be inclusive of providing bamboo scaffoldingMake: Jotun,Asian Paints, Berger Paints, Dulux Paints or equivalent. |
| 51 | Providing and applying two coat of primer and two coats of Texture paint, Anti-fungal, water proof, dust proof Paint on Exterior Surfaces in any pattern, at all heights of surfaces. One component waterborne 100% pure acrylic emulsion that offers protection against concrete carbonation with an R Value of min 600m and an equivalent concrete layer thickness value of min 150cm. Paint should have crack bridging property of min 1.85 mm with Solar Reflective index of min 110 and IR reflectance property. The product shall have a Volume Solids of minimum 35%The product shall be independently tested and approved for properties alike Carbon Dioxide Diffusion resistance, resistance to chloride diffusion, crack bridging and liquid water/ vapour transmission as well as SRI properties. The product can be like Jotashield WaterXtreme Topcoat of Jotun Paints or approved equivalents.Two Coats of above paint should be applied using a conventional Roller / Airless spray at the site after application and curing of applied Primer.including cleaning, preparing the surface, applying primer - scraping by sandpaper, scaffolding etc. including - (a) All surface preparation, suitable number of base coats required, primers and suitable finishing to the complete satisfaction of the Engineer in Charge, (b) Scaffolding and all leads and lifts,(c) Proper curing in between the two subsequent coats, (d) Touch ups to the paint after the scaffolding is removed, (e) All measurements for paints to be as per IS-1200. f) Minimum Guarantee of TenYears Waterproofing and Paint performance for all external paints by manufacturer .Formeasurement of painting items the area painted shall be considered without any multiplication factor for different kinds of surfaces painted. Rate shall be quoted accordingly. All painting items final finish shall be as per manufacturer\"sspecification as per acceptance of Engineerin charge /Architect. No extra payment shall be made for extra/over coat if required.Make - Asian Paint Ultima Allura Torino, Jotun Jotashield Tex Fine OR Equivalent. |
| 52 | Providing material and labour for fixing suspended FALSE CEILING -made out of 12.0 mm (apprx.) thick Gypsum Plaster Boards of gyproc or equivalent made G.I standard section framework. -The G.I. Section frame work shall be tied to the roof and walls with the anchor fastener screws/bolts of appropriate size recommended by the manufacturer . -The boards shall be fixed to the frame work with the screws and the joints shall be flushed and finished with requisite jointing compounds paper tapes etc.-the ceiling will have 300mm wide plywood band will finish in1mm thick laminate having Burma teak texture as shown in drawing.-The surface shall be finished evenly by applying putty, sand papering, applying primer & paint of approve make and type evenly complete with designer ceiling with part ply + laminate as shown in drawing -making all necessary provision and cut outs for all electrical boards, wiring, HVAC , plumbing etc. fittings, fixtures and cleanliness as per detailed design and drawing or as directed by engineer in charge. -height of false celling will be approx. 3000mm from Floor finish level,-Price shall include any ledge, grove, offset, edging in sq.mt. only. -Length X breath of false ceiling will measured for payment. as directed by Engineer-In-Charge etc. complete. (RA) |
| 53 | Providing, supplying, and installing high‐performance modular HDPE Drain Cells made from UV-stabilized, injection-molded high-density polyethylene, having a minimum compressive strength of 70–120 t/m² and a void ratio of not less than 90%. The drain cells shall be of size 500×500 mm or 750×500 mm with a thickness of 25/30/50 mm (as specified), designed with an interlocking grid structure to ensure continuous sub-surface drainage, rapid water flow, and aeration. Each panel must allow vertical discharge of at least 20 L/m²/sec and provide lateral drainage pathways for protection of waterproofing membranes. The drain cell system shall include a layer of non-woven geotextile fabric (150–200 GSM) over the surface to prevent soil clogging, ensuring long-term drainage efficiency. Installation shall be done over waterproofing with proper alignment, interlocking, and edge restraints as per manufacturer’s guidelines and engineer-in-charge approval. |
| 54 | Providing, supplying and fixing precast cement concrete saucer drain units of approved design, size and shape, manufactured using machine-vibrated concrete of M30 grade with required reinforcement, including finishing the surface smooth, lifting, loading, unloading, transporting, placing in position, jointing with 1:3 cement mortar, cutting/trimming where required, preparing the bedding with PCC 1:4:8 / M10 grade (100 mm thick), aligning to required line and level, backfilling and compacting around the drain, and curing complete as per drawing, specification and direction of the Engineer-in-Charge. |
| 55 | Providing and fixing precast concrete kerb stone of size 600 mm (length) × 300 mm (height) × 150 mm (thickness) made of design mix M-250 grade concrete, manufactured by vibration compaction process using approved quality cement, coarse and fine aggregates, water, and required admixtures, confirming to IS standards.Kerb stones shall have smooth, uniform surface, chamfered/rounded edges as per drawing, and shall be free from cracks, honeycombing, surface defects or color variation. The rate shall include cost of moulds, curing, stacking, transportation to site, loading, unloading, and all handling charges.The kerb stones shall be installed on a cement concrete foundation of mix M-10 grade (1:3:6 nominal mix) of minimum 100 mm thickness, with 10 mm mortar bed in 1:4 cement mortar. Kerb shall be set to line, level, curvature and gradient as per engineer’s instructions. Joints between kerb stones shall be filled with cement mortar (1:3) or as specified by the Engineer-in-Charge, including making provision for expansion joints where specified.Backfilling on both sides, including compacting with suitable material, shall be carried out after proper alignment. The work includes cutting, trimming, and forming corners, curves, and transitions to achieve required geometry, using smaller segments if necessary.Curing shall be done adequately during manufacturing and after installation, as directed. The rate includes all labour, materials, tools, equipment, testing, and making the work complete in all respects. Make:- Vyara and Supertiles or equivalent. |
| 56 | Supply and Installation of PVC Strip CurtainSupply and installation of high-quality transparent/reinforced PVC strip curtain for cold storage, including:PVC strips of thickness 5 mm and width 200 mm, suitable for temperatures down to 5°C.Strips shall be anti-static, anti-bacterial treated, and fire-retardant.Galvanized steel/aluminum top mounting brackets, rails, and fasteners, corrosion-resistant and suitable for cold storage conditions.Proper alignment, cutting to door dimensions, and overlap of strips 50–100% as per door width.Rate includes supply, delivery, installation, testing, and commissioning of the curtain. |
| 57 | Providing and applying road marking with hot applied thermoplastic paints with reflectorizing glass beads on bitumen/RCC surface providing and laying a hot applied thermoplastic compound 2.5 mm thick including reflectorizing glass beads @ 250gms per sqm area, thickness of 2.5mm is excluding of surface applied glass beds as per IRC:35-2015. The finished surface to be level, uniform and free from streaks and holes. zebra patta /bump patta lane/center line/ edge line/cut patta. The white color marking should provide liminance coefficinet on cemend road shalll be min 130 mcd/m2/lux and Asphalt road shall be min 100 mcd/m2/lux during the service life during the day time. The marking should meet the performance criteria for night time reflectivity, wet reflectivity and skid resistance as mentioned in the section-15 of IRC 35-2015. Warranty for the Retro reflectivity should be two years. |
| 58 | Providing and Fixing Aluminium Foil Bubble Insulation Sheet 8 mm Thick with work includes providing and fixing aluminium foil bubble insulation sheet of 8 mm thickness under roofing and cladding sheets. The insulation shall consist of a polyethylene bubble core of double bubble structure, laminated on both sides with reflective aluminium foil. The total thickness shall be 8 mm. The reflective aluminium surface shall have a minimum reflectivity of 95% and emissivity not more than 0.03. The insulation material shall conform to relevant ASTM and BS standards for fire rating, thermal performance and vapour barrier characteristics. The thermal resistance (R-value) shall not be less than 1.9 m²·K/W.The insulation shall be installed below the roof sheeting or cladding sheeting and fixed to the purlins or girts using self-drilling screws, galvanized washers, nylon straps or other accessories as recommended by the manufacturer. All sheets shall be installed with a minimum overlap of 50 mm on all sides. All longitudinal and transverse joints shall be sealed using aluminium foil tape of minimum 50 mm width to ensure an airtight vapour barrier. The insulation shall be laid with slight sag between the purlins to create an air gap that enhances thermal performance. Care shall be taken to avoid puncturing or tearing the foil surface during installation.The item includes supply, transportation and handling of insulation sheets, aluminium tape, fixing accessories, labour, equipment, scaffolding and all incidental materials required to complete the work in all respects. It also includes cutting around roof openings, ridges, gutters, skylights and other penetrations, and ensuring continuous vapour barrier throughout the installation.The measurement shall be in square metres of the actual finished surface covered, and the rate shall include all wastage, overlaps, tapes and accessories. Makes approved include Supreme, Aerolam, Reflectofoil or equivalent as approved by the engineer-in-charge. |
| 59 | Supply, fabrication, and installation of sign board made of high-quality acrylic plate 5 mm thick with computer-cut vinyl lettering, including rounded edges, mounting hardware, and protective finish. The work includes fixing the sign board on wall/door with screws, studs, or adhesive as required, complete with all labour, materials, tools, and accessories for proper alignment and finish as per approved design and specifications. |
| 60 | Providing material and labor for fixing ACRYLIC LOGO FOR \" OMNIBUS INDUSTRIAL DEVELOPMENT CORPORATION LIMITED DADRA NAGAR HAVELI & DAMAN & DIU (LIQUOR DIVISION) \" (Size: 20.00m x 0.750m)-3D acrylic letters flushed in R.C.C. BEAM.- ACP frame should be fix inRCC beam/slab while casting with propare clamp and anchor fastener.-SIDE EDGES (300mm)-3mm thk. 75mm wide white ACP sheet inside the beam/slabACRYLIC SHEETS & ITS TECHNICAL PARAMETERS (to be used for logo)-Front: a. 3mm thk White transparent imported (Mitsubishi/equivalent) acrylic cutting on laser cutting machine. LED Light - 3smd module-Making all necessary provision of material and electric wring etc fittings, fixtures and cleanliness as per detailed design and drawing or as directed by chief engineer in charge.LEDBack lit:Pasting new vinyl stickers over the ACRYLIC substrate shall be undertaken with all care and techniques such as using pre mask tapes to the vinyl before initiating the fixing of the same over the acrylic sheets, it shall be ensured that vinyl is properly aligned to the acrylic without any gaps at the outer edges, there are no air bubbles, etc., -The workmanship shall be of high standards and chief engineering. Vinyl for the logo: The vinyl ( LG/Avery/3M or equivalent) |
| 61 | Supply, delivery, and installation of roof-mounted Turbovent 20inch dia natural ventilation unit for godown/warehouse, including cutting of roof opening, base-flashing/mounting plate, sealing and weatherproofing, fastening/fixing, and all labour, materials, tools, and accessories for proper alignment and commissioning.Specifications:Material: Aluminium body, corrosion-resistantConstruction: Aerofoil vanes/blades with sealed low-friction bearings for smooth rotationRoof Compatibility: Suitable for profiled metal sheets or industrial roofingOperation: Wind-driven, no electricity requiredScope Includes: Supply, transport, roof opening & modification (if required), flashing & sealing, mounting, finishing, testing and commissioning. |
| 62 | Providing, supplying and fixing polycarbonate roofing sheets of approved make, colour and profile, having minimum thickness 3 mm (solid sheet). The sheet shall be manufactured from UV-stabilized, high-impact strength polycarbonate resin and UV protection on top surface to prevent yellowing and degradation.Sheets shall be in standard industrial trapezoidal/corrugated profile matching the adjacent roofing system, with rib height and pitch as per manufacturer’s design. The sheet shall have minimum impact strength 200 times that of glass, excellent thermal stability, and shall comply with ASTM D 1003, ASTM D 638, ASTM D 790 or equivalent IS standards for clarity, tensile strength and flexural properties.The polycarbonate sheet shall be fixed over the purlins using self-drilling/self-tapping fasteners of SS-304 grade with EPDM washers of required size at crest/rib, ensuring water-tightness. Proper aluminium or polycarbonate end caps, ridge flashing, and corner profiles shall be provided where required. All cut edges shall be sealed with manufacturer-recommended sealant to prevent moisture and dust ingress.Installation shall include providing neoprene/EPDM filler pieces, butyl tape, anti-dust tape, and all accessories required for a complete and leak-proof installation. Overlaps shall be minimum 150 mm (side lap) and 200 mm (end lap) or as recommended by manufacturer. Sheets shall be installed with care to avoid scratches, cracks or stress marks.The work shall include cutting, aligning, positioning, drilling, fixing, finishing, and complete installation and as directed by the Engineer-in-Charge. The contractor shall ensure proper safety measures while working at height.Make: Lexan / Sunlite / Tuflite / Sabic / Polygal / Equivalent approved.Unit of Measurement (UOM): Square metre (sqm) |
| 63 | Providing, designing, fabricating, supplying, transporting to site, erecting and completing in all respects Pre-Engineered Steel Building Structure comprising all types of structural steel members, complete on tonnage basis (MT), excluding roofing and wall cladding sheets, but including all accessories, erection consumables,Grout, labour, equipment, tools & machineries required for installation.The scope shall include but not be limited to the following components:A. Structural Steel Members Included (PEB Main & Secondary Members)Primary Steel Members: MAKE JSW/TATA/ESSARTapered/Built-up / Hot rolled columns, rafters, beams, canopies, end wall frames, crane brackets, posts, portal frames.Material grade: HR Plates IS 2062 E350, HR Sections: E250 as per project design. Secondary Members: MAKE JSW/TATA/ESSARCold formed Z & C purlins, eave struts, girts, sag rods, flange bracings, gable end bracing, knee bracing & ancillary support systems.Material: Cold formed section as per IS 801, steel confirming to IS 800:2007. Bracing SystemCross bracing, cable bracing, portal bracings, struts & ties for longitudinal/lateral stability.Base Plates, Stiffener Plates, Cleats, Clips, Gusset plates, etc.B. Fabrication StandardsDesign of hot-rolled and built-up sections as per:AISC Manual, MBMA standards, IS 800:2007Fabrication includes cutting, bending, drilling, shop welding, machining and assembly using qualified procedures.Welding Process: SMAW/SAW/MIG as per AWS D1.1 Structural Welding Code. All members shall be shop fabricated and delivered in finished condition.C. Surface Preparation & Painting/CoatingSurface Preparation: Shot blasting of primary steel to appropriate SA standards. Primary Members Coating: Synthetic enamel primer with minimum 120 microns DFT, factory applied. Secondary Members: Pre-galvanized coating 120 GSMAnchor Bolts: Supplied in black steel as specified.D. Erection & InstallationScope of work includes:Unloading, staging, hoisting, alignment, bolting, welding (if required), tightening & full erection at site.Use of cranes, tools, torque wrenches, scaffolding, consumables and safety equipment is included.All connections shall be bolted using high tensile bolts with required washers & nuts.Incluing Grouting with GP2 Grout.E. Material Standards (To be Followed)Component Material SpecificationHR Plates/Sections IS 2062 E350/E250 (JSW/Eissar/Tata Cold Formed members IS 800/IS 801 compliant steels Bolts & Fasteners High Tensile SDS – Alloy Coated with EPDM WasherAnchor Bolts Manufacturer supplied, black steelF. Exclusions from this ItemRoofing Sheets – To be paid separately.Wall Cladding Sheets – To be paid separately.Civil Works (foundation, RCC pedestals, grouting).Plumbing/Electrical works.Turbo vents, ridge ventilators, skylights unless taken as separate items.Unit of Measurement (UOM)Metric Ton (MT) – Based on issued construction drawings & actual fabricated/installed quantity duly certified by Engineer-in-Charge.Make: -Avlon or Equivalent as approved by Chief Engineer. |
| 64 | Providing, supplying and installing 40mm thick FR (Fire Retardant) grade PUF insulated sandwich panel for wall/roof/partition applications, made of factory-finished pre-coated metal sheets on both sides with rigid polyurethane foam insulation in between, complete with all necessary accessories as specified.The panel shall consist of outer and inner metal sheets of 0.50 mm thick (±0.02 mm)pre-painted galvalume (PPGL), having zinc/aluzinc coating ofAZ150 with polyester top coat and epoxy back coat. Panel shall have tongue-and-groove interlocking joint with proper sealing arrangement.The insulation core shall be rigid polyurethane foam (PUF) of 40 ± 2 kg/m³ density, factory injected under high pressure, with thermal conductivity of 0.022–0.024 W/mK and ≥95% closed cell content. The panel shall be of Fire Retardant (FR) grade, self-extinguishing type, conforming to DIN 4102 B2 / equivalent FR standards.The item includes supplying all required flashings, corner angles, trims, J-channels, butyl tape, EPDM gaskets, and self-drilling screws with EPDM washers. Installation shall be done true to line and level, including joint sealing, cutting, fixing and alignment complete in all respects.The work includes loading, unloading, shifting, handling, cutting, installation and finishing complete as directed.Unit of Measurement: sqm (square meter). |
| 65 | Providing, supplying and fixing colour coated PPGL (Pre-Painted Galvalume) sheet of 0.5 mm total coated thickness for roofing and cladding, including all necessary accessories, fasteners, sealants, labour and equipment, complete as directed.The PPGL sheet shall be made from high tensile steel of minimum 550 MPa strength, with Aluminium-Zinc alloy coating AZ150 (150 g/m²) on both sides, conforming to ASTM A792 / IS 15965. The sheet shall have factory-applied colour coating consisting of 20–25 micron top coat and 5–10 micron back coat.The sheet shall be supplied in approved profile (trapezoidal / hi-rib type), having an effective cover width of approx. 1000–1100 mm and crest height of 28–35 mm, as per manufacturer’s standard. The base metal thickness shall not be less than 0.45 mm.The work includes supply and installation of all related accessories such as ridge pieces, corner trims, barge channels, drip trims, gutters, down-take accessories, foam fillers, butyl tape and silicone sealant. Fixing shall be done using self-drilling fasteners with EPDM washers, ensuring leak-proof installation. Side laps and end laps shall be provided with proper sealant as required.Sheets shall be cut only with nibbler or shear (no gas cutting). All handling, lifting, alignment, and fixing shall be done carefully to avoid damage to the colour coating. Complete work includes providing scaffolding, safety arrangements, transportation and all tools required to finish the work.The item shall be measured in square meter (sqm) of finished covered area. |
| 66 | Supply, surface preparation, and application of high-visibility, durable, skid-resistant marking paint for forklift pathways inside the warehouse. The work includes cleaning and preparing the floor by removing dust, grease, and other contaminants to ensure proper adhesion, followed by application of yellow (or as per safety standard) pathway lines, arrows, pedestrian crossings, stop markings, hazard zones, and other necessary floor symbols as per the layout drawings approved by the Engineer-in-Charge. The paint shall be industrial-grade, quick-drying, and suitable for concrete surfaces. All work must comply with applicable safety standards, ensure clear visibility for forklift operators and pedestrians, and include curing/drying time, site cleanup, and temporary warning signs or barriers during execution. Quantities and layout to be confirmed on-site prior to painting under the guidance of the Engineer-in-Charge. |
| 67 | Supply and installation of column edge protection in the warehouse using 50 mm × 50 mm x 6mm steel angle sections. The work includes cutting, fabricating, painting (yellow & black bands) and fixing the steel angles to all exposed edges of columns to protect against impact from forklifts, trolleys, and other warehouse equipment. The steel angles shall be properly aligned, anchored, and finished with anti-corrosive primer and suitable paint as approved by the Engineer-in-Charge. All work shall comply with applicable safety standards, ensure durability and maximum protection to the column edges, and include cleaning of the site after installation. Quantities and exact locations of column protections to be verified on-site by the Engineer-in-Charge. |
| 68 | Point wiring for Light / Bell with2-1.5 sq.mm& earth wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires up to 10 mtr length , in below type of pipe erectedwith 6A Modular type switch / bell push & accessories and earth continuityof following type, erected on PVC / Metallic/Wooden box, single mounting base framecovered with textured/metallic/white front plate modules erected on /in wall / ceiling as per pipe erected, with necessary Lamp holder/ceiling rose / H.D.Connector as directed.(f) with medium class Rigid PVC pipe and accessories erected concealed inwall/ceiling complete cat III |
| 69 | PointwiringforTissino/Modularsecondarylight point with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (green) both are of ISI marked 1.1 KV grade FRLS PVCinsulatedmultistrandcopperwires,inbelow typeof pipetobeerected completewithearth continuityandnecessaryconnectionwithprimary lightwithaccessorieserectedon Metal/ PVC/ wooden box covered with 3 mm thick PC(Polycarbonate) / Acrylic sheetfor open / concealedwiring.withnecessaryLampholder/ ceiling rose / H.D.Connector as directed.Note:- Maximum up to 6 mtrs length, excess will be considered asMains for Secondary Point.(f) with medium class Rigid PVC pipe and accessories erected concealed inwall/ceiling complete cat III |
| 70 | Point wiring for FAN with 2-1.5 sq.mm& earth wire of1.5sq.mm(Green)bothareof.ISImarked1.1 KV GradeFRLS PVC insulated multi strand copper wiresupto10mtrlength,inbelowtypeofpipe erectedwith 6A Modular type switch and hum free EME steptypeelectronicfanregulator mounted and accessorieswithearthcontinuityoffollowing type erected on PVC / Metallic/Wooden box, single mountingbaseframecoveredwith textured/metallic/white frontplate modules erected on/inwall/ceilingasperpipeerected.with necessary ceiling rose / H.D.Connector as directed.(f) with medium class Rigid PVC pipe and accessories erected concealed inwall/ceiling complete cat III |
| 71 | Point wiring for Individual Plug with& earth wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires up to 10 mtr length, in below type of pipe erectedcomplete with Modular type switch & 5 pin Plugerected on PVC / Metallic/Wooden box covered with appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following type of accessories [II]For16APlugand16ampswitch with2-2.5 sq.mm Cu. Wire from mcb db board.(f) with medium class Rigid PVC pipe and accessories erected concealed inwall/ceiling complete cat III |
| 72 | Point wiring for Individual Plug with& earth wire of1.5sq.mm(Green)bothareofISImarked1.1 KV gradeFRLSPVCinsulatedmultistrandcopper wiresupto10mtrlength,inbelowtypeofpipe erectedcomplete with Modular type switch & 5 pin Plugerected on PVC / Metallic/Wooden box coveredwithappropriatefrontplatemodules erected on / in wall / ceiling as per pipe erected with following type of accessories. [I] For 6A Plug and 6 a switchwith 2-1.5 sq.mm Cu. Wire from nearby switchboard/mcb db board (f) with medium class Rigid PVC pipe and accessories erected concealed inwall/ceiling complete |
| 73 | Point wiring for on board Looped Plug with 6A Modular type switch & 5 pin socket erected on PVC / Metallic/Wooden box, single mounting base frame covered with textured / metallic/whitefront plate modules erectedon/ in wall / ceiling with following type accessories Cat. III |
| 74 | Providing& erecting Switchboard for Computer or electricapparatusconsistingof followingmodular typeaccessories mounted withPVC/Metallic concealed/open box with single mounting base framecoveredwithtextured/metallic/whitefront plate,moduleserectedwithnecessaryconnections as directed1 no. 6A/16A universal plug-switchcombined. 3 nos. 6A Switch3 nos. 6A 5 pin PlugFor Modular Type Accessories Cat. III |
| 75 | Providing following type of Modular Type AccessoriesmountedwithPVC/metallic/Wooden box, single mounting base frame covered with textured / metallic/white front plate , modules erected withnecessaryconnectionsaspersite situation directed by Engineer In charge.(8)ComputerRJ-45 socketCat.III |
| 76 | Supplying & erecting approved make LAN cable of following size in existing pipe as per direction [C] CAT - 6 |
| 77 | Providing following type of Modular Type AccessoriesmountedwithPVC/metallic/Wooden box, single mounting base frame covered with textured / metallic/white front plate , modules erected withnecessaryconnectionsaspersite situation directed by Engineer In charge.(3) Two Pin/RJ-11 Telephone Socket[A] For One Gang Cat.III |
| 78 | Supplying&erectingapprovedmakeTelephone CableelectrolyticcopperconductorPEinsulation twistedintwopairs,&wrappedwithFRLSPVC tape&sheathedwithFRLSPVCorHFFRouter Jacket suitable for telephone wiring & confirming to C-DOT erected in existing pipe. of following size of conductors&nos.ofpairs.Withnecessary connections.[A] Conductor Size 0.5 mm(a) Unarmoured (2)Two Pairs |
| 79 | Providing & erecting main Distribution (MDF) indoortype,backmountedframeasperDoTstandard approved with krone strips(a) Suitable for 10 pair |
| 80 | providing and erecting Mains with ISI marked, 1.5KVgradeelectrolytemultistranded,annealed copper conductor with heat resistant PVC insulated conformstoIS694,IEC-227erectedinexisting pipe offollowing size (Specifically for control panel, relays, power switchgears, motor starters & control wiring)withrequiredsizeofcopperlugs,nutsand bolts if required.(f)One wire 10.00 sq. mm |
| 81 | providing and erecting Mains with ISI marked, 1.5KVgradeelectrolytemultistranded,annealed copper conductor with heat resistant PVC insulated conformstoIS694,IEC-227erectedinexisting pipe offollowing size (Specifically for control panel, relays, power switchgears, motor starters & control wiring)withrequiredsizeofcopperlugs,nutsand bolts if required.(g)One wire 16.00 sq. mm |
| 82 | providing and erecting Mains with ISI marked, 1.5KVgradeelectrolytemultistranded,annealed copper conductor with heat resistant PVC insulated conformstoIS694,IEC-227erectedinexisting pipe offollowing size (Specifically for control panel, relays, power switchgears, motor starters & control wiring)withrequiredsizeofcopperlugs,nutsand bolts if required.(h)One wire 25.00 sq. mm |
| 83 | providing and erecting Mains with ISI marked, 1.5KVgradeelectrolytemultistranded,annealed copper conductor with heat resistant PVC insulated conformstoIS694,IEC-227erectedinexisting pipe offollowing size (Specifically for control panel, relays, power switchgears, motor starters & control wiring)withrequiredsizeofcopperlugs,nutsand bolts if required.(i)One wire 35.00 sq. mm |
| 84 | ProvidinganderectingMainswith1.1KVgrade FRLSPVCinsulatedISImarkedstrandedCopper conductor wire in following typeof pipetobe erectedconcealedin/flushedonwall/ceiling,with1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity offollowing size. (A) With medium class Rigid PVC pipe and accessories (a) 2 wire 1.5 sq. mm |
| 85 | ProvidinganderectingMainswith1.1KVgrade FRLSPVCinsulatedISImarkedstrandedCopper conductor wire in following typeof pipetobe erectedconcealedin/flushedonwall/ceiling,with1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity offollowing size. (A) With medium class Rigid PVC pipe and accessories(b) 2 wire 2.5 sq. mm |
| 86 | providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size(A) With medium class Rigid PVC pipe and accessories (a) 2 wire 4 sq. mm |
| 87 | providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size(A) With medium class Rigid PVC pipe and accessories (c) 2 wire 10 sq. mm (use earth wire of 4 sq.mm ) |
| 88 | providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size(A) With medium class Rigid PVC pipe and accessories (g) 4 wire 4 sq. mm |
| 89 | providinganderectingMainswith1.1KVgrade FRLSPVCinsulatedISImarkedstrandedCopper conductor wire in following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper conductorFRLSPVCinsulatedstrandedwireof green colour for earth continuity of following size(A) with medium class Rigid PVC pipe andaccessories(i)4 wire 10 sq. mm(use earth wire of 4 sq.mm ) |
| 90 | Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected on/in wall or ceilingerected with necessary PVCfittings&Junctionboxesfixedwithadhesive solution&Clampswithfollowingdiaofpipes,in approved manner as directed (b) 25 mm |
| 91 | Providing & erecting PVC Corrugated Flexible Conduit with required nos. of coupling, PVC bushes, Check-nuts etc. complete of followingsizes.(2) 25 mm |
| 92 | Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mountedfittedwithbusbar,neutrallink,earth barandDINrail,ConformstoIS8623-1&3, IEC 61439-1 & 3 without MCB to house appropriate nos. ofMCBs.(The DBsshould be usedofsamecompanyofMCBtobeused) suitable for(A) single phase incoming and horizontal single phase outgoing(b) sheet steel double door (IP-43) (ii)6 way |
| 93 | Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mountedfittedwithbusbar,neutrallink,earth barandDINrail,ConformstoIS8623-1&3, IEC 61439-1 & 3 without MCB to house appropriate nos. ofMCBs.(The DBsshould be usedofsamecompanyofMCBtobeused) suitable for(A) single phase incoming and horizontal single phase outgoing(b) sheet steel double door (IP-43) (iii)8 way |
| 94 | Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mountedfittedwithbusbar,neutrallink,earth barandDINrail,ConformstoIS8623-1&3, IEC 61439-1 & 3 without MCB to house appropriate nos. ofMCBs.(The DBsshould be usedofsamecompanyofMCBtobeused) suitable for(B)threephaseincomingandsinglephase horizontaltypeoutgoing Perphaseisolationtype (PPI)(b) sheet steel double door (IP-43) (i)4 way |
| 95 | Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mountedfittedwithbusbar,neutrallink,earth barandDINrail,ConformstoIS8623-1&3, IEC 61439-1 & 3 without MCB to house appropriate nos. ofMCBs.(The DBsshould be usedofsamecompanyofMCBtobeused) suitable for(B)threephaseincomingandsinglephase horizontaltypeoutgoing Perphaseisolationtype (PPI)(b) sheet steel double door (IP-43) (ii)6 way |
| 96 | Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mountedfittedwithbusbar,neutrallink,earth barandDINrail,ConformstoIS8623-1&3, IEC 61439-1 & 3 without MCB to house appropriate nos. ofMCBs.(The DBsshould be usedofsamecompanyofMCBtobeused) suitable for(B)threephaseincomingandsinglephase horizontaltypeoutgoing Perphaseisolationtype (PPI)(b) sheet steel double door (IP-43) (iii)8 way |
| 97 | providing and erecting Miniature circuit breaker singlepole6Ato25Asuitabletooperateon240 V A.C. system and having breaking capacity 10KAtobeerectedinexistingbox. confirming to IS 8828/1996 with ISI Mark Cat.III |
| 98 | Providing&erecting240VMCBdoublepole switch for lighting Load (B Curve) having 10 KA breakingcapacity&confirmstoIS:8828in existing box having following capacity(A) 6 to 32 Amp. Cat-III |
| 99 | Providing&erecting240VMCBdoublepole switch for lighting Load (B Curve) having 10 KA breakingcapacity&confirmstoIS:8828in existing box having following capacity(B) 40 Amp. Cat-III |
| 100 | Providing & erecting 415 V MCB Four Polefor Motor & InductiveLoad (C Curve) having 10KA breakingcapacity&confirmstoIS:8828in existing box having following capacity(a) 6 to 32 Amp. Cat III |
| 101 | Providing & erecting 415V MCB Four Pole Switch for Lighting Load (B curve) having 10KA breakingcapacity&confirmstoIS:8828in existing box having following capacity(b)40 Amp. Cat.III |
| 102 | providing and erecting Approved make RCCBs conformingtoIS:12640 andhaving sensitivity of30mAandShortCircuitwithstandcapacity of10KAandsuitableforoperationonsingle phase 240 V,50Hz. having characteristic of quick action & tripping with all advance feature & do not incorporate any electronic component. for following Max. ratingerected as directed (i) 25 Amps.DP Cat. III |
| 103 | providing and erecting Approved make RCCBs conformingtoIS:12640 andhaving sensitivity of30mAandShortCircuitwithstandcapacity of10KAandsuitableforoperationonsingle phase 240 V,50Hz. having characteristic of quick action & tripping with all advance feature & do not incorporate any electronic component. for following Max. ratingerected as directed (ii) 40Amps. DP Cat. III |
| 104 | Supplyinganderectingtriplepole&neutral 440V/500VpanelmountingCopperBusbars withfourequalNos.ofelectrolytebushaving current density not more than 1.6 Amp. / sq.mm(Ratedcurrent/crosssectionarea) dulywrappedwithcolourinsulatingtapefor phasesequenceoffollowingcurrentcarrying capacity, erected with necessary bus bar supports /insulators, main cable socket to each bar, erected in existing cubical panel with necessaryconnections.(C) Suitable for 300 Amp. capacity |
| 105 | ProvidinganderectingApprovedmakeFour pole moulded case circuit breaker having breaking capacity ICU of 25 KA. at 415 V,havingnormalcurrentratingupto25Ato 100A.withFixedthermal&magneticrelease suitable to work on A.C. supply 50 c/s. with all internal connections, spreader tinned copper & completeerectedinexisting16G.M.S. housing. |
| 106 | ProvidinganderectingApprovedmakeFour pole moulded case circuit breaker having breaking capacity ICU of 35KA. andabove at 415V .havingnormalcurrentrating 250A. with variable thermal & magnetic release suitabletoworkonA.C.supply50c/s.withall internal connections, spreader tinned copper & completeerectedinexisting16G.M.S. housing. |
| 107 | Providing & erecting weather proof, dust & vermin proof, floor mounted front operated indoor typecubical panel board necessary IP- 42 and above protection as per approval from engineerinchargemadefrom14SWGthick CRCM.S.sheetforouterbody&doors,16 SWGthickCRCM.S.sheetforinternal partitions with necessary accesories , supporting angles/ flats channel including cutting,bending,drilling,welding,rivetingwith internalpartitions&cablealleyasper requirements&instructionofengineer-in- charge with erection of supplied switch gears, BUSBARS,suitable sizeofinterconnectingPVCcopperwire/ copper-aluminium strips, rubber grommets, rib, bakelitecontrolfuses/MCBformeasuring instruments, earth bus & earth bolts, foundation flange-bolts-basePlates,sufficientnos.of hinged doors, handles with locking arrangement and rubber gasket,heavy duty end terminal connection,danger notice board,necessary ventilation,earthing strip complete. The Panel shall be painted with epoxy powder coating (Theratesexcludesthecostofswitchgears, busbars,interconnectingmains &Copper Aluminium strips,meters, Fuses etc. The dimensionshallbemeasuredexcludingbase beams) The panel shall be supplied with followingapprovedmanufacturerswithfollowing size.(B)Thestandardcompaniesswitchgearshall be used and only manufacturers at CPRIapproved factory. (i) with 350mm depth board |
| 108 | Providing , erecting , fabricating the M.S. structure as per requirement on site incorporating proper size of M.S. angles,square,round,flats,bars,channels, sections completewithcutting,welding, grinding&finishingdulypaintedwithonecoat of red oxidewith erection on site as per directionofengineerinchargewithnecessary grouting, cementing, plastering & finishingcomplete. |
| 109 | Supplying and erecting approved make suitable panel indicatorLED type lamp, lens cover, complete erected with necessary connections. |
| 110 | Providing & erectingL.T. Current Transformer withbarprimary50/5to1000/5ratio15VA burden erected in existing CRCA box duly securedwithinsulatingmaterialsconnectedto the meter. |
| 111 | Providinganderectingmetallicvitrifieddanger noticeboardasperlanguagesuggestedby engineer incharge for MEDIUM VOLTAGE installation to be erected as per IS-2551. |
| 112 | Providing following type of Modular Type AccessoriesmountedwithPVC/metallic/Wooden box, single mounting base frame covered with textured / metallic/white front plate , modules erected withnecessaryconnectionsaspersite situation directed by Engineer In charge.(7) Blank Plate Single |
| 113 | ProvidinganderectingApprovedmakeEarth faultRelaysuitabletomountwithinter connectionsuitableto followingsizeof moulded case circuit breaker having CT ratio& MCCB rating as following along withshunt trip 220V AC. with all internal connections & complete erected in existingM.S.housing.(3) 250 A -400 A , CT Ratio 1/400 |
| 114 | Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for1.1 KV. to be laidon wall with necessary clamps or in existing trench/ pipe of following size of cables. (C) 3 core 6 Sq. mm |
| 115 | Providing and erecting XLPE(IS:7098)(I)-88 ISI armouredcablemultistrandAluminium conductorfor 1.1KV.tobelaid onwallwith necessary clamps or in existing trench/ pipe of following size of cables(B) 3 1/2core 35 Sq. mm ( 16 Sq. mm 1/2 core) |
| 116 | Providing and erecting XLPE(IS:7098)(I)-88 ISI armouredcablemultistrandAluminium conductorfor 1.1KV.tobelaid onwallwith necessary clamps or in existing trench/ pipe of following size of cables(G) 3 1/2 core 150 Sq. mm ( 70 Sq. mm 1/2core) |
| 117 | Providing and erecting XLPE (IS:7098)(I)-88 ISI armouredcablemultistrand/SolidAluminium conductorfor 1.1KV.tobelaid onwallwith necessary clamps or in existing trench/ pipe of following size of cables(A) 4 core 4 Sq. mm |
| 118 | Providing and erecting XLPE (IS:7098)(I)-88 ISI armouredcablemultistrand/SolidAluminium conductorfor 1.1KV.tobelaid onwallwith necessary clamps or in existing trench/ pipe of following size of cables(B) 4 core 6 Sq. mm |
| 119 | Providingand,fixingheavydutyflangetype brasscableglandwithrubberringforPVC insulatedarmouredcablecompletewithout going tails, insulating tape etc for following size of cables.(A) 2 to 4 core 2.5 / 4 Sq. mm |
| 120 | Providingand,fixingheavydutyflangetype brasscableglandwithrubberringforPVC insulatedarmouredcablecompletewithout going tails, insulating tape etc for following size of cables.(B) 2 to 4 core 6 Sq. mm |
| 121 | Providingand,fixingheavydutyflangetype brassdoublecompressiontypecablegland withrubberringforPVCinsulatedarmoured cablecompletewithoutgoingtails,insulating tape etc for following size of cables.(B) 3 & 1/2core 35/50 Sq. mm |
| 122 | Providingand,fixingheavydutyflangetype brassdoublecompressiontypecablegland withrubberringforPVCinsulatedarmoured cablecompletewithoutgoingtails,insulating tape etc for following size of cables.(F) 3 & 1/2 core 150 Sq. mm |
| 123 | Solder less crimping type Aluminium lugs conforming to IS suitable for cable of following sizeevenly crimpedwithhighpressuretool& connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner.(A) 1.5/ 2.5/4/6 Sq.mm |
| 124 | Solder less crimping type Aluminium lugs conforming to IS suitable for cable of following sizeevenly crimpedwithhighpressuretool& connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner.(D) 35/50 Sq.mm. |
| 125 | Solder less crimping type Aluminium lugs conforming to IS suitable for cable of following sizeevenly crimpedwithhighpressuretool& connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner.(H) 150 Sq.mm. |
| 126 | Supplying & erecting earth pit of minimum bore dia.150mmsizeapprovedmakeEarthing ElectrodeconsistingPipe-in-PipeTechnology as per IS 3043-1987 made of corrosion free hot dippedG.I.PipeshavingOuterpipediaof 50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm having 200-250 Micron galvanising,connectionterminaldiaof12mm with constant ohmic value surrounded by highly conductive compound with high charge dissipationsuitableforfollowingtypeof applications with chamber and heavy duty cover. (A)(approvedmake OEM has to submit testcertificateincludingvalueofearth resistance of installation duly stamped and signedbyagencyandofficerInchargehasto ensurethevalueofearthingresistane mentionedintestCertificate)&havingback fillingcompoundof(B) Innerchemical(CCM Compound)- Resistivity:- 0.2 ohm / meter testingasperIEC62561-2017,Voltagedrop:-< 1 volt at no load & dry form, Sulphar content:-<2%(C)BackfillCompound :-Earthing compound should be capable to retain moisture forlongtime Necessarytestreportmustbe submitted by Agency.(c)For ElectricalInstallation covering Transformer Neutrals, Lightning arrester Earthing,A.C.Plant&SensitiveComputer System(like Automation, SCADA) i.e independent Earthing in normal soil.Length of Pipe : 3.00 mtrsBack filling Compound :2 nosBags of 25 Kg. |
| 127 | Providing, supplying, erecting, testing, and commissioning (SITC) of annealed bare copper wire of size ranging from 8 SWG to 16 SWG, suitable for electrical earthing and bonding applications. The copper wire shall be of high conductivity, soft-drawn, and tinned (if required), conforming to relevant IS standards. Installation shall be carried out as per site requirements and directions of the Engineer-in-Charge, ensuring proper termination and continuity. |
| 128 | Providing & erecting Approved make Power Saving 50 Watt Ceiling Fan with double ball bearing ISI mark with Condenser 230 volt A.C. 50 Hz 1200 mm sweep complete having3blades with aluminium blades with , canopy & 30 cm. down rod erected with earthing.(Make shall be approved by Engineer in charge)) |
| 129 | Supplyinganderecting19/20mm.nominal bore Medium Class M.S. Pipe down rod erected duly painted for fan complete with proper insulation without leakage and earthing. |
| 130 | Supplying& erecting fan hook box of 10 mmM.S. round bar bounded to the RCC bars up to 50mm length each side and pierced through a16GaugeM.S.box/HeavyDutyPVCbox complete erected concealed in Ceiling with necessary finishing. |
| 131 | Providing2.5mm.thicklaminatedacrylicsheetto cover the fan hook or Fan box. |
| 132 | Supplying & erecting approved make low noise decorativeexhaustfanhavingsquareframe ABS body with inbuilt lowers & square frame.200mm with 1350RPM Cat.II |
| 133 | Providing recess in wall or window frame suitableforerectionofExhaustfancomplete with plastering and colour washing to match the colourofthewallorwindowcompletewith expanded metal in order to render the fitting in accessible and the room water-proof. |
| 134 | Supplying and erecting led lamps with following wattage capacity of 220 to 240 voltage, minimum 15000 burning hours life, 500 V in built-surge protection,Polycarbonate diffuser, mounting suitable for E14 / E27 / B22 lamp holders, pf >= 0.5(A) LED Lamps integral type, with PC diffuser suitableLAMP holder (ii)5 to 8 watts CAT III |
| 135 | Supplying and erecting LED indoor fittings with LEDsofwattage0.2Wattto0.5Watt assembledonsingleMCPCB,withhousing usedasaheatsinkshallbemadeofthick sheet Steel conforming to IS: 513/CRCA/aluminiumpressurediecast powder coated and high U.V. & corrosion resistance withdiffuser housedinaluminium casted body with company mark/name 160Vto270V,PowerFactormorethan0.95, THD < 15 %, CCT3000 K to 6500K, Luminaire efficacy> 85 lumens/watt , LED driver efficiency > 85 % ( fitting required LM-79 & LM-80 Certificates)(NOTE:Belowdescriptionhave shown ranges of Wattage capacity of LED fittings.TheEngineerinchargemayselectany wattage capacity between the ranges shown.)(A) Square/ Circular shaped Surface/Recessed Mount Downlight with provision for spring loaded mounting clips complete.IP20 (iii) 16-20 watts, Surge-2 KV cat - III |
| 136 | Providing following type of Modular Type AccessoriesmountedwithPVC/metallic/Wooden box, single mounting base frame covered with textured / metallic/white front plate , modules erected withnecessaryconnectionsaspersite situation directed by Engineer In charge.(19) Modular Indicating Call Bell |
| 137 | Supplying & erecting recess wall mounting speaker with 5W rated input power 3.3 K. Ohms / 3W impedance, 100 - 10000 Hz frequency response with 6 inch dia. cone type 8 ohms speakers duly fitted in ABS plastic cabinet of colour match with wall or ceiling of following size.[[Approved by Competent Authority i.e. not Below the rank of Executive Engineer ](b)Square shaped 260 x 260mm size speaker |
| 138 | Supplying & erecting Amplifier having following specification:Power Output :250W (RMS) (300W Max.)inputs : 6 Misc. & 2 Aux.frequency Response :50-1500HZ I3dbTone Controls :Cut & Boost typeLED Meter:5 LED ArraysThe amplifier suitable to operate 240V A.C.& 24volt D.C. (Battery) with automatic changeover from AC to Battery operation, duly protected by wrong Battery Polarity connections. [[Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] |
| 139 | Supplying and erecting Flexible PVC insulated multi strand multi core 1.1 kv grade ISI marked copper wires of following size to be erected as directed.(d) 1.50 Sq.mm 2 core round PVC sheathed |
| 140 | Providing & erecting water cooler having storage capacity 150 Ltr. & cooling capacity 150 Ltr.per hour @ an ambient temp of 45˚ C. The outlet temp. of the water should drop by 15˚C within a hour, The water cooler should be comprising of hermetically sealed compressor, fan motor, condensing unit, water tank surrounded by evaporating, coil, thermostats, relay etc.complete with necessary inlet & outlet connection. The body of water cooler will be made from Stainless Steel. |
| 141 | Supplying & erecting reverse osmosis (RO)water purification system with M.S. powder coated pedestal frame, prefilter housing carbon filter suitable buster DC pump, auto low & high pressure switches with following size of LPH capacity & erected as directed [F]500 LPH with3 phase Raw water pump of 1000LPH @ 3.0 kg/cm2 (1No - Kirloskar /CRI /Lubi), Dual media filter 13\"x54\" - (1No),Micron catridge filter 20\" x 4.0\"-1No, High pressure pump 1000LPH @ 11kg/cm2- (1No - lubi/ Shimge/ CRI), RO Membrane housing with RO membrane of 40*40 - (2 Nos), RO pressure tube 4\" x 2E -(1No), 0-2400 LPH Rotameter ( 2Nos), , Dosing pump 0 -6 LPH - (1 No),. with 100 Ltr Dosing tank- (1 No), with Recovery Rate 50%. |
| 142 | Supplying and erecting approved make Conical Pole (Standard ) Made from HR sheet steel. The pole should be made as per IS. and shall be coated with hot dip galvanizing as per IS 2629/2633/4759 with required base plate and integral Junction box consist of terminal plate of min 6mm Hylam sheet, standard profile 35mmX7.5mm Din-Rail for MCB Mounting, stud type terminal and arrangement for cable terminationas erected on suitable foundation (included) with necessary nut-bolts/J-Bolts.as per details given by manufacturer considering site requirement.The length of poles are as below.(E) 7 Mtr. Long 65mm Top X170 mm bottom dia, 3mm thickness. |
| 143 | Providing1:2:4 cement concrete foundation & 70 % PCC from bottom including excavation for the pole of size 45 x 45 x 100 cm. Deep in below ground level with plinth of 45 cm x 45 cm (or 45 cm dia x 45 cm) high upper ground level with necessary curing and finishing in approved manner.( for 4 & 6 mtr pole) |
| 144 | Providing and erecting street light pole bracket comprising main B Class MS pipe of 4.2 cm/require outside dia. complete with suitable B Class M.S. sleeve tubing of approx. 45cms.length and suitable for 76.5 mm / 80mm. / require size pole top having sufficient fasteners for fixing the brackets and having spread of 1 mtr. length with suitable rise as per site condition & suitable welded stiffener reducer and nipple with check nut complete painted with one coat of Red oxide / PU base primer and two coats of Aluminium / PU paint. paint with following nos of arms. [A] Single Arm bracket 1 Mtr |
| 145 | Supplying & erectingapproved makeSMC press moulded composite FRP.loop-in, loop-out approx. 2mm thick box complete with Bakelite connector strip 5way(3P+N+E),DIN rail for mounting mob& hinged doors as per requirement having locking arrangements with mounting clamp with nuts, bolts & washers suitable for erection on pole with cable clamps& earth bolt of following size of box.(A) 300mm x 200mm x 100mm[deep] |
| 146 | Supplying and erecting LED street light / Flood light fittings with High power White LEDs wattage of 3 Watt and above assembled on single MCPCB, efficiency more than 130 lm/w and corrosion free High pressure die cast aluminum housing with smooth finish powder coated and heat sink extruded aluminium with diffuser and Polycarbonate optics/ lenses, with toughened glasswith company mark/name engraved or embossed 160 to 270 V,Power Factor more than 0.95, THD < 10 %, CCT3000 K to 5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED driver efficiency > 85 %.(fittings required LM-79 & LM-80 certificates)(NOTE: Below description have shown ranges of Wattage capacity of LED fittings.The Engineer incharge may select any wattage capacity between the ranges shown.)(A) Street Light (IP-65), Surge protection -4KV integral and ,Light must have 440VAC line supply with over-voltage protection. (i) above 36 to 48 watts Cat-lll |
| 147 | Providing and fixing Terminal board of size 5.0 x 127 x 152.4 mm.bakelite sheet with suitable brass studs with nuts, washers and clamps of size 25mm x 3mm suitable for pole painted with one coat of red lead paint. |
| 148 | Supplying & erecting approved make Digital time switch having lithium cell 6 years operative and operate battery backup 1 channel day clock with 14 memory programme, suitable to operate on 240V + 5%, 16A with, floating contacts Minimum switching setup time 1 minimum & LCD display. Also comprised permanent ON/OFF switching. Programming switches & housed in fire proof thermoplastic enclosure & transparent cover erected as required with necessary connection erected as directed. |
| 149 | Supplying & erecting power contactor ,AC3 duty for time switch complete erected as per direction Cat III (B) 2 pole 250V 32 Amp. |
| 150 | Supplying and erecting Flexible PVC insulated multi strand multi core 1.1 kv grade ISI marked copper wires of following size to be erected as directed. e) 1.50 Sq.mm 3 core round PVC sheathed |
| 151 | Supplying and erecting B class Galvanized iron pipe having smooth finished bore of the pipe on both ends erectednuts and boltsalong the pole / wall shaping the pipe as per site requirement. Pipe dia as following.(C) 40 mm dia. |
| 152 | Providing and erecting Pipe type earthing with 40 mm dia 2.5 mtr long \"B\" grade G.I. pipe with necessary coupling buch buried in specially prepared earth pit & G.I. earth wire of 8 SWG erected & connected as directed (For panel)For using salt and charcoal / coke as required for pipe type earthing. |
| 153 | Providing & laying approved makeDouble walled corrugated pipes (DWC) of polyethylene(conforming to IS 14930 II )with necessary connectingaccessories of same material at required depth in existing trenchfor laying ofcable. below ground/ road surface for enclosing cable (A)50 mm outer dia |
| 154 | Providing&erecting240VMCBdoublepole switch for lighting Load (B Curve) having 10 KA breakingcapacity&confirmstoIS:8828in existing box having following capacity(A) 6 to 32 Amp. Cat-III |
| 155 | Making trench in Hard Murrum / Tar Road of suitable width of 90 cm or requireddepth for laying any size of cable or locating the faultall over the run and back filling the same and making the surface as normal ground. |
| 156 | Making trench in soft soil of suitable width of 90 cm deep for laying cable or locating the faultall over the run and back filling the same and making the surface as normal ground. |
| 157 | S.I.T.C. submersible pump set suitable for bore of 100 mm. dia. or more having three phase motor capacity not more than 5 H.P. with following capacity . Lifting and Lowering taken extra.(B) (16 stage) 140 to 180 LPM discharge at 96 to 69 mtrs. head respectively suitable for 50mm dia. delivery pipe cat III |
| 158 | Providing and erecting ISI marked PVC insulated PVC SheathedFlat flexible Submersiblecopper cable approved make offollowing Size. (C) 3 Core x 4 Sq. mm |
| 159 | Providing & erecting open well horizontal mono block pump set with cast iron body, complete forthree phase submersible motor having[C] For 3 HP 3 phase open well horizontal mono block pump set suitable for 85 LPM to 270 LPM @ 11 mtr to 33 mtr head suitable for 50/65 mm dia delivery pipeCat II |
| 160 | Supplying & erecting approved make Automatic liquid level controller 6A. with sensor testing as per instruction of Engineer in charge on site complete with wiring connection with existing wires , with copper conductor from pump to upper and lower tank. |
| 161 | Supplying & erecting approvedmake motor control cubical panel [Star delta] made from 16G CRCA sheet duly epoxy powder painted inside and outside with hinged doors and locking with suitable size of ON - OFF isolator (AC 3 / 23 duty) main fuses. Digital volt and current meter (in a single unit) with micro controller based control unit and current sensing single phasing preventer electronic overload protection, over voltage (Programmable) protection and under voltage (Programmable) protection, prod less dry run protection programming facility for setting of all parameter like overload current, high voltage limit, low voltage limit, dry run limit with digital indication on seven segment LED display for any fault like over load, high voltage, low voltage, dry running single crimped, electronic star delta timer, feather touch start / stop push buttons to be erected on angle iron frame. Grouted on wall the contactors will be of L& T, Siemens, BCH make only)(A) DOL up to 5.0 H.P. |
| 162 | Supplying and erecting, commissioning and testing of Diesel Generating setconfirming to IS: 4722:1968 & BS:5514having continuous rating, 3 phase, 415 volts, 50 cycles A.C. supply comprising of a totally enclosed air/water cooled diesel engine with multi-cylinders developing suitable BHP not less than following capacityat 1500 RPM with 10% overload for one hour in 24 hours with standard accessories like fly wheel, lubricating oil cooler, \"A\" class governor, heavy duty fuel wheel and lubricating oil filter, oil bath air filler, lubricating oil pressure gauge, end exhaust manifold, standard set of tools with adjustable spanners, screw drivers, cylinder head to cover, joint cylinder head to exhaust, element lube oil filter, 12 / 24 volts electric starting equipment complete with standard heavy duty battery, dynamo, cut-outs, ammeter, necessary wiring, pressure gauge, starter etc and heavy duty Residential type exhaust silencer and vertical hot air duct both logged with asbestos rope, save oil trays, exhaust piping of required length, standard wall/floor mounted fuel with level indicator and piping anddrip proof alternator, self excited, self regulated, screen protected, with excitation system, capable of delivering the rated system output at 415 volts, 3 phase, 0.8 PF, 50 Hz, 4 wire, running at 1500 RPM, conforming to IS-4722- 1968 with voltage regulation+/- 5% of rated voltage from no load to full load. Both the engine and alternator fitted on a common fabricated steel base plate with antivibration mounting engineand alternator both connected to each other by flexible flange coupling and with floor/wall mounted control panel box comprisingof voltmeter ammeter, selector switches, ACB / MCCB / MCB of adequate capacity, indicator lamps duly wired with HRC fuses. The alternator & control panel shall be connected with provided suitable capacity armoured cable and complete with Acoustic enclosure (canopy) made out of 16 SWG CRCA Sheet, sound absorbing material Rockwool of 64 density & 100 mm thick conforming to IS:8183 / PU Foam of 40 Density - at least 40 mm. The resin bonded rockwool covered from inside the canopy by perforated sheet with 3/4 mm holes, sound level not more than 75 dB at a distance of 1 mtr, as per PVCT norms. Erection, commissioning and satisfactory testing as per requirement with first filling of fuel, oil, etc. with guarantee / Warrantee of complete system for Two years. & with obtaining all necessary certificate from Electrical Inspector. The Capacity and Ratings of DG sets are as below.(R) Continuous rating of 250 KVA ,BHP not less than 309 BHP |
| 163 | Providing & erecting approved make AMF control panel suitable for following size of3 phase, 415 V., 50 cycles, A.C. diesel generating set complete of scope as detailed below: 1) Power module:A pair of electromechanically interlocked contactors (for mains & generator) Overload relay for generator contactor Neutral contactor for mains and generator Power socket for connections. 2) Control and metering module: Line voltage monitor. Generator voltage monitor Ammeter 3 items attempt start facility. Air circuit breakers/MCB/MCCB of suitable rating for auto/manual operation. Auto/manual switch. Emergency stop push buttons. Manual start push button. frequency meter. Engine hour meter. Two earthing studs.3) Protection module: The engine shutdown in the unlikely event of Low lube oil pressure High cylinder head temperature. V belt failure.4) Indicators with alarm Load on generator.5) Indicators Load on mains Engine fails to start . Emergency stop battery charger.The AMF Panel of following capacity(D) AMF Control Panel for200 KVA/250 KVA3 phase DG Set |
| 164 | Providing and erecting multifunctional meter suitable for application of Power monitoring and showing measurementof following Voltage, Frequency, Apparent energy, Apparent power, Active and reactive energy, Active and reactive power, Average voltage Vavg, Peak demand power PM, QM, SM, Demand power P, Q, S, Apparent power S, S1, S2, S3, Unbalance current, Power factor and displacement PF (signed, four quadrant), Calculated neutral current, Active, reactive, apparent energy (signed, four quadrant), Active power P, P1, P2, P3, Voltage U21, U32, U13, V1, V2, V3, Phase currents, Average current Iag, Peak demand currents, Reactive power Q, Q1, Q2, Q3, Demand current I1, I2, I3, [Us] rated supply voltage 40...300 V AC 45...65 Hz, 40...300 V DC, Network frequency 50 Hz, Type of network 3P, Display type 7 segments LED, Display colour Red, Messages display capacity 3 fields of 4 characters, Display digits 12 digit(s) - 14.2 mm in height |
| 165 | Supply, Installation, Testing and Comissioning of 4MP Varifocal Lens Dome Type Camera, H.265 4MP IR Turret Dome N/W Camera, Manual Varifocal 2.8-12mm, 50M, Micro SD, DC12V/PoE, IP67/IK10, Basic IVA, 4MP resolution (2560 × 1440), True day/night, Digital WDR, 3D DNR, HLC & BLC, Triple streams, Smart codec by ROI, Built in MIC, Cyber SECURITYy, Basic intelligent video analytics, Audio In, NDAA Compliance, UL, CE, FCC Certified(Including Five year free maintenance with guarantee) |
| 166 | Supply, Installation, Testing and Comissioning of 4MP Varifocal Lens Bullet Camera, H.265 4MP IR Bullet N/W Camera, Manual Varifocal 2.8-12mm, 50M, Micro SD, DC12V/PoE, IP67/IK10, Basic IVA, 4MP resolution (2560 × 1440), True day/night, Digital WDR, 3D DNR, HLC & BLC, Triple streams, Smart codec by ROI, Cyber SECURITYy, Basic intelligent video analytics, NDAA Compliance, UL, CE, FCC Certified(Including Five year free maintenance with guarantee) |
| 167 | Supply, Installation, Testing and Comissioning of 64 Channel Network Video Recorder (NVR), Dual OS design, HDD Hot Swap with RAID support, N+1 hot spare configuration, Support 16CH@2MP, H.265/H.264 Video Compression, HDMI, VGA output, up to 8 SATA interface each with max 10 TB support and 1 eSATA, 16-ch synchronous playback at up to 1080p resolution, Gigabit Ethernet network interfaces, bandwidth 320 mbps, CE FCC, BIS, Operating Temp -10 deg to 50 deg C, USB and serial Interface, RAIDsupported(Including Five year free maintenance with guarantee) |
| 168 | SITC of SCREEN SIZE 80 cm diagonal (32” INCH), RESOLUTION HD(1366*768), USB INPUT (2.0 SUPPORT) 2*Side(USB2.0), HDMI INPUT 3*Side(HDMI 1.4), USB DEVICE SUPPORT USB Supported HDD, HOTEL MODE Yes, Basic, BLUETOOTHYes (Ver. 4), WIFI TYPE(STANDARD) 802.11a/b/g/n 2.4G 2T2R, Built-in, WIFI BAND TYPE 2.4GHz, OS & VERSION INFO Android \"P\" - 9.0, MEMORY FLASH 8GB EMMC, RAM 1.5GB , DDR3 2133 Mhz. (Including Five year free maintenance with guarantee) |
| 169 | SITC of 48 x 10/100/1000BASE-T ports4 x Gigabit GbE/SFP combo portsAdvanced L2 switching and SECURITYy featuresL2+ Static RoutingOptional “standard mode” or “surveillance mode” management user interface[Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] |
| 170 | Supply, Installation, Testing and commissioning of 6 TB Surveillance Series Hard disk supporting 24X7 operational efficiency |
| 171 | Providing & Erecting Netwrok rack with following capacity with Necessary cooling fan,Cable manager,6A PDU,equipment rack with necessary mounting accessories.(D) 15 U |
| 172 | Providing and erecting Inverter based approved make split air-conditioning unit consisting of condensing unit with variable speedfan motor, inverter type hermetically sealed rotary compressor with accessories etc. duly connectedseparatelyerectedevaporatingunit and blower motor with its accessories by means ofextra supplied proper insulated copper tubing,drain PVC pipes suitable for ( cost includesEcoFriendlygreengaschargingand 15Aplugtop&RemoteControl&MSStand) with necessary core cutting.(1)For 3 Star Rating of current year(C) for 2.0ton capacity - Premium Cat.(1)For 3 Star Rating of current year |
| 173 | Providing and erecting Inverter based approved make split air-conditioning unit consisting of condensing unit with variable speedfan motor, inverter type hermetically sealed rotary compressor with accessories etc. duly connectedseparatelyerectedevaporatingunit and blower motor with its accessories by means ofextra supplied proper insulated copper tubing,drain PVC pipes suitable for ( cost includesEcoFriendlygreengaschargingand 15Aplugtop&RemoteControl&MSStand) with necessary core cutting.(1)For 3 Star Rating of current year(D) for 2.5ton capacity - Premium Cat. |
| 174 | Providing and installing a complete HVAC system for maintaining temperature inside a 1000 sqm cold storage area. The work includes supplying all HVAC equipment, air handling units, outdoor condensing units, refrigerant piping, ducting, insulation, controls, and electrical connections. The system must be capable of handling heat load, infiltration and maintaining uniform temperature throughout the storage area.The HVAC equipment shall include factory-made AHU indoor units with insulated double skin panels, capacble of maintainng 15degeree celcius in peak summer, cooling coil, blower motor, drain pan and vibration pads. Outdoor units shall be air-cooled type with scroll compressors, condenser coil and weatherproof housing. Refrigerant piping shall be copper of required sizes with proper brazing and 19 to 25 mm thick insulation.Ducting work includes fabrication and fixing of GI sheet metal ducts of required thickness, with supporting hangers, access doors, turning vanes and dampers. All ducts must be insulated with 50 mm thick PUF or rockwool insulation with aluminium foil vapour barrier. Supply air diffusers and return air grills must be provided at suitable locations.The work includes providing temperature controllers, sensors, control panel, wiring, safety cut-outs and interlocking for smooth operation. Electrical works include power and control cabling, earthing and termination. Drain piping for AHU condensate shall be provided using UPVC/CPVC pipe with proper slope and insulation where required.aThe contractor shall carry out testing, commissioning, balancing and trial run of the complete HVAC system. The system should run for at least 72 hours continuously during commissioning. All equipment should comply with IS and manufacturer standards.The job includes all materials, labour, tools, consumables and accessories required for a complete working HVAC system. Make: - Daikin, Blue Star, Voltas, Carrier or Equivalent as approved by Chief Engineer. |
| 175 | \"Providing, erecting, testing & commissioning approved make oil immersed ONAN cooled, double wound, core type indoor / outdoor copper wound 11KV/ 433V step down transformer of following capacities operating on 3 phase, 50 Hz 4 wire & neutral earthed system continuously rated for a full temperature rise in oil not exceeding 45 Deg.C.at maximum ambient temp. of 50 Deg. C. complete with necessary radiator first filling of new transformer oil & standard fitting as below complying withIS 1180( Part 1 ):2014 standards with energy efficiency level 2 Off load tap changing range steps +2.5% to -5% on H.Vfor variation should be provided. The H.V. shall be connected Delta & Secondary with star connection. The transformer should have cable-end boxes on H.T. side suitable for up to 3 core 150 sq.mm. XLPE cable & on L.T. side suitable for bus duct or cables as per requirement complete with test certificates from manufacturers1. Oil conservator with filling Hole &Cap -One No. 2. Thermometer pocket with 6\"\" dial typethermometer switch alarm & trip contacts-Two nos.3. Silica-gel breather with charge- OneNo.4. Plain oil level gauge -One No.5. Drain / Sampling / Filter valve- One No. 6. Top Filter Valve -One No. 7. Explosion vent with Diaphragm -One No.8. Rating & Diagram plate - One No.9. Additional neutral bushing for earthing - One No. 10. Bi directional Roller - Four Nos. 11. Earthing terminals - Two Nos.12. Lifting lugs - Two Nos. 13. Air release plug. - One No.14. Double float buchholz relay withAlarm and trip contacts.15. Control cable as required from Transformer to VCB Panelis to be provided with necessary connection to VCB relays for protection. as per IS 1180 level-2 (b)315 KVA Max. allowable loses at 50 % of rated load is 1.025 KW and at full load is 3.1 KW \" |
| 176 | Providing, and erecting 11 KV D.P.9 mtr. high Structure made of 6\" x 3\"‘I’-Section Girder, 4\" x 2\"channels, clamps, nuts, bolts etc.Suitable for erection of the followings duly connected with necessary ACSR conductors. as per drawing approved by the Engineer- in charge complete with following. Height as per IS 7 Mtr above ground ) (A) 11 KV 200 Amps Drop out fuses with S.R.B.P. tubes carries.-Three nos (B) 11 KV G.O.D. switch complete with insulators, operating handle with galvanisedpipe, Sq.bar etc. 400 Amp.-OneSet (C) 11 KV lightening arrestor with clamp-ThreeNos. (D) 11 KV shackle insulators- SixNos. (E) The above D.P. structure should be earthed with 25 mm.X 3 mm thick double copper earth strips run separately and connected with separate copper plate earth electrode |
| 177 | Providing and erecting ISI Marked 3core 240 Sq.mm XLPEinsulated 11 KV armoured cable Aluminium conductorIS-7098 to be laid on wall with clamps or in provided cable trench / pipe approved manner as directed. |
| 178 | Providing and erecting cable end termination kit, heat shrinkable Push on type Densons/ Raychem/ Elastimold make suitable for 11 KV XLPE cable 3core 95 & 120 Sq.mm (A) Outdoor type |
| 179 | Providing and erecting cable end termination kit, heat shrinkable Push on type Densons/ Raychem/ Elastimold make suitable for 11 KV XLPE cable 3core 95 & 120 Sq.mm (B) Indoor type |
| 180 | Providing, erecting, testing commissioning & getting Plan Approval as well as NOC from Electrical Inspector for extensible H.T panel comprising of one 400A. H.T. VCB incoming & Two outgoing 400 ADrawout type VCB confirming as per I.S. for use on 11 KV, 3 phase, 50 c/s. unearthed A.C. supply system having breaking rupturing capacity of 350 MVA complete with spring operated mechanism, mechanically & automatic ON-OFF and spring mechanism charged, discharged indicators, ON-OFFmechanical push button, operation counter necessary auxiliary switches, closing shunt trip, air insulated busbar chamber having heat shrinkable PVC sleeves, mechanical interlocks safety shutters, isolating plugs and a VCB trolley with three vacuum interrupters with epoxy support insulators and self aligning finger type isolating contacts.The breaker shall be Manual cum motorised mechanism & auto spring charge with TNC switch closing with following accessories.1. 144 mm. square flush mounting type digital multifunctional meter with communication facility - Three sets.2. Power Factor Meter One No3. Double core current transformer cast resin type having ratio 200 to 50/1 core for metering & second core for protection having required class of accuracy. - Three Sets4. Instantaneous under voltage relay& Temperature rise Tripping Relay5. Electrical closing coil & short trip coil operating on 110V.D.C.- Three Sets 6. Auxiliary relay for anti pumping device7. Three phase Three limb Drawout type feeder connected & output of 200 VA cast resin insulated potential transformer having ratio 12000V./110V. and 200 VA Burdon with 0.5 accuracy. - One No.8. Common Alarm bell operating on 110V A.C.- One No. 9. Digital KWH Meter - One No. 10. Cable boxes suitable up to11 KV 3core 150 sq.mm XLPE cable. - Three Nos11. 230V. A.C. to 110V. D.C. power pack for closing & tripping circuitcommon.12.Breaker ON-OFF, Auto trip and spring charged indicators. - Three Sets.13.Phase indicating & panel illumination lamps with plug socket - Three Sets.14.Numerical Communicable type non directional O/C & E/F Relay witha setting of 5-250% both in O/C & E/F. -Three Setcomplete with necessary interconnection with air insulated high grade copper busbar{Breaker Testing scope include Closing Time, Opening Time, VCB Hi-Pot test at Site}{ Relay Testing Scope Include testing of all protection by three phase testing kit at site }(VCB Trolley is to be provided) |
| 181 | Supply, Installation, Testing & Commissioning of following size of Grid Tied Solar Power Plant with Solar Panels (ALMM approved): Frame Material :Anodized Aluminum alloy Frame With Twin Wall Profile, Front Cover : High Transmission Low-Iron Tempered Glass (AR Coated), High efficency and positive power tolerance Pmax: 0/+5, Module Efficiency should be approx.18%-21%,Normal operating temperature 45\"C, Junction Box with Waterproof IP67 & MC4 Compatible and Enclosed with Bypass diodes, 100% Electroluminescence test to ensure error free Modules, Thep. temp. co-efficient of the PV module shall equal or better than -0.45%/degree C. Solar PV modules of minimum fill factor 75% to be used. Unit Production:- 4 to 5 Unit /kw /day (Actual)(1Year Avg) With 10 year Product warranty and 25 year Linear Power Warranty., Solar Inverter: MPPT Range: 80-1000 V, Max efficiency: 97.5% - 98.9%, O/p Frequency: 50/60Hz, Operating Altitude (m) ≤4000, O/p Power Factor: ~1, O/P THDi: <3%, Operating Tempreture Range: -25~60°C, Anti-islanding Protection: Integrated, Input Reverse Polarity Protection Integrated, Insulation Resistor Detection Integrated, Residual Current Monitoring Unit Integrated, Output Over Current Protection Integrated, Output Short Circuit Protection Integrated, Output Over Voltage Protection Integrated, Protection Degree: IP65, User Interface LCD & APP,Datalogger & Communication: GPRS / Wi-Fi, Module Mounting Structure: Seamless Box Pipe / \"C\" Channelof suitable size for rooftop solar installations with good stability agaist wind & weight load., Hot Dipped Galvanized steel coils. suitable arrangement for base plate for foundation , solar panel mounting, the structure should be suitable for carry the load of solar panel,wiring, sprinkler system etc. with necessary foundation work/wall mount, j bolt, anchor fastner etc. the nut bolt used for installtion of stucture should be (SS 304) quality. and Balane of System with necessary Swithgears (Suitabel size and protection of ACDB & DCDB), inter connecting wiring, earthing system, lightining arrester system, all liasoning work with various gov. dipartment like state nodal agency,DISCOM & CEIG is included in agency scope (Excluding GEDA Application fees, Solar connectivity Charges, Meter connectivity Charges, Meter testing Charges.)(F) Grid Tied Solar Power System: 101 - 250 kW (3 - phase) |
| 182 | Providing & erecting Automatic solar panel cleaning system for solar power projects which includes necessary plumbing work (UPVC pipes and accessories) from source of water to project site (upto 30 meters),Suitable size of sub mercible/ open well motor, necessary wiring for motor and sprinkler system with safety, timer circuit for automatically on/off the sprinkler system, necessary size oand number of nozzles/JET (minimum 1 Nozzle/Jet per module).(F) 101KW-200KW Cleaning System |
| 183 | Providing and fixing in position cowel went to pipes.(B) 75mm dia. |
| 184 | Providing and fixing in position cowel went to pipes.(B) 100mm dia. |
| 185 | Providing and fixingwash down water closet European type WC pan (Wall Hung) like JAQUAR CNS-WHT-961SPP- SIZE 365x545x360MM and P trap distance 23.5 cms with integral P trap including jointing the trap with soil pipe in cement mortar 1:1 (1 cement : 1 find sand) including providing and fixing of 1)Health Faucet hand shower heavy duty with SS braided hose 1.2 MT long pipe to water closet - JAQUAR ALD-CHR-573 with Single Piece Slim Concealed Cistern Body with Installations Kit & “S-Type” drain pipe connection set for Wall Hung WC (without Flush Control Plate) - JCS-WHT-2400S with Control Plate Opal - JCP-CHR-152415,Toilet roll holder -Jaquar -ACN -1151N etc,completeMake:-Jaquar/Cera/Parryware/Hindware or Equivalent as approved by architect |
| 186 | Providing and fixing plastic seat and cover for wash down water closer with C.P. brass hinges and rubber buffers. (B) Black plastic seal and cover. |
| 187 | Providing and fixing toilet paper holder.(A) C.P. Brass |
| 188 | Providing and fixing 12.5 LTRs low level flushing cistern with a pair, of C.I. or Mild brackets, complete with fittings such as lead valve less syphon, 15mm nom.nal size brass ball valve with polythene float, C.P brass handle unions and couplings for connections, with inlet, outlet and overflow pipes, 40mm dia. porcelain enamelled flush bend including cutting holes in walls and making good the same connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately)(A) Vitreous China (I) In white colour |
| 189 | Providing and fixing washbasin with single hole for pillar tap with C.I. or M.S. brackets painted white including sutting holes and making good the same but excluding fittings.(A) Vitreous China:(ii) Flat Back washbasin 550 mm x v 400mm size. (i) In white colour.of approved make Jaquar, cera, Hindware or its equivalent as approved by architect |
| 190 | Providing and fixing C.P. brass waste for washbasin or sink. (B) 40mm dia. |
| 191 | Providing and fixing M.I. fisher union for washbasin or sink. (B) 40mm dia. |
| 192 | Providing and fixing 600mm x 450mm bevelled edge mirrror of superior glass mounted on 6mm thick A.C. sheet or plywood sheet and fixing to wooden pluge with C.P. brass screws and washers. |
| 193 | Providing and fixing pillar tap, capstan head, screw down high pressure with screws, shanks and back nuts. (i) 15mm dia. Make:Jaquar/Cera/Parryware/Hindware |
| 194 | Providing and fixing chromium plated, bottle trap with necessary couplings of approved quality for wash basin. |
| 195 | Providing and fixing pillar tap, capstan head, screw down high pressure withscrews, shanks and back nuts. (ii) 20mmdia. Make:Jaquar/Cera/Parryware/Hindware |
| 196 | Providing and fixing screw down bib taps of following size.(B) Brass chromium plated screws down Bib Tap. (i) 15mm dia. |
| 197 | Providing and fixing Gun metal check or non-return fullway wheel valve.(D) 15mm dia. |
| 198 | Providing and fixing Gun metal check or non-return fullway wheel valve.(D) 25mm dia. |
| 199 | Providing and fixing Gun metal check or non-return fullway wheel valve.(D) 32mm dia. |
| 200 | Providing and fixing Gun metal check or non-return fullway wheel valve.(D) 40mm dia. |
| 201 | Providing and fixing Urinal of approved quality including connection with trap and with integral longitudinal flush pipe.(A) Squating plate pattern white earthenware size of urinal370mm x 315x 620 mm.of jaquar make code no URS -WHT-132530including (1) Providing and fixing SS finish waste couplingof 32 mm dia size half theread with 80mm height like jauar -ALD - 709 for wash basin with rubber plug (2) Providing and fixing SS finish bottle trap with internal partition of 32mm size with 250mm &190mm long wall flange connection pipes and wall flange like jaquar ALD-769 of approved quality with necessary fitting for wash basin (3) SS finish flush valve of auto closing system like jaquar PRS-073 of approved quality and connection with waste pipe trap etc. complete |
| 202 | Providing and fixing chromium plated brass half trun flush cock of approved quality including fixing in pipe line etc. complete.(i) 20mm dia. |
| 203 | Providing and fixing ball cock of approved. quality asdirected.(B) Abonite (ii) 50mm dia. |
| 204 | Providing and fixing G.I. Rain water spout of 50mm dia. and 30cm. length. |
| 205 | Providing laying and jointing in true line and level 15mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concealed as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials. |
| 206 | Providing laying and jointing in true line and level 25mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concealed as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials. |
| 207 | Providing laying and jointing in true line and level 32mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concealed as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials. |
| 208 | Providing laying and jointing in true line and level 40mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concealed as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials. |
| 209 | Providing laying and jointing in true line and level 50mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concealed as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials. |
| 210 | Providing, laying and jointing in true line and level 110 diametre U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with EACH other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 110 mm diametre x 149 mm length x 145 mm heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials. |
| 211 | Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm diameter with jali of the following nominal diameter of self cleansing design with C.I scread down or hinged grating including the cost of cutting and making good the walls. |
| 212 | Providing and fixing S.W. gully trap with C.I. grating brick masonry chamber and water tight C.I. cover with frame of 300mm x 300mm size (inside) with standard weight.(i) Square mouth traps. (A) 100mm x 100mm size P type. |
| 213 | Providing laying (to level or slopes) and jointing reinforced concrete Light duty non-pressure pipes I.S. class NP2 of the following internal diameter with collars and butt ends prepared for collar joints including testing of joints complete.(B) 150mm |
| 214 | Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1- cement :2-coarse sand : 4-graded stone aggregate 20mmnominal size) foundation concrete 1:3:6 mix (1-cement : 3- coarse sand :6-Brick bats 40 + 50mm size) inside plastering 15mm thick with Cement Mortar 1:3 (1- Cement : 3-coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1 Cement :2-Coarse sand :4-stone aggregate 20mm nominal size) finished smooth complete including curing and festing (i) Inside size 900mm x 1200mm and 1.5M. deep including C.I. cover with frame size 560mm diameter total weight of cover and frame to be not less than 128 kgs. (Wt. of cover 64 KG and Wt. of frame 64 KG)(A) With 230mm thick walls of brick msonry using brick having crushing strength not less than 35KG / Sq.cm. in Cement Mortar 1:5 (1- Cement: 5-Coarse sand) (2) B type depth 1.50 Metre for 150mm diameter sewer. |
| 215 | (II) Extra rate for constructing B.B. masonry for everyadditional depth of 0.1M. GR Part thereof over item No.24.27 (I) for depth from 1.50M. to 2.25M. |
| 216 | Providing and fixing cast iron steps of size 500mm x150mm x 22.5mm and painting with two coats of Anti corrosive paint etc. complete. |
| 217 | Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with bricks having crushing strength not less than 35Kg/Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x 610mm intenal dimensions total weight of cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1 cement :2- coarse sand :4-graded stone aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete.(i) Inside dimensions 455mmx 610mm and 450mm deep for single pipe line. |
| 218 | Extra over items 24.44 for every additional depth of0.1M. of part thereof beyond 450mm depth for Brickmasonry chamber.(i) for 455mm x 610mm size. |
| 219 | Constructing brick masonry chamber for undergroundC.I. Inspection chamber and bends with bricks havingcrushing strength not less than 35Kg/Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x 610mm intenal dimensions total weight of cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete.(ii) Inside dimensions 500mm x 700 mm and 450mm deep for pipe line with one or two inlets. |
| 220 | Extra over items 24.44 for every additional depth of0.1M. of part thereof beyond 450mm depth for Brickmasonry chamber.(ii) for 500mm x 700mm size. |
| 221 | Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with bricks having crushing strength not less than 35Kg/ Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x 610mm intenal dimensions total weight of cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1 cement :2- coarse sand :4-graded stone aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete.(iii) Inside dimensions 600mm x 850 mm and 450mm deep for pipe lines with three or more inlets. |
| 222 | Extra over items 24.44 for every additional depth of0.1M. of part thereof beyond 450mm depth for Brickmasonry chamber.(iii) for 600mm x 850mm size. |
| 223 | Providing and fixing heavy-duty health faucet made of chromium-plated brass / stainless steel, with flexible hose, wall-mounted hook, and necessary fittings including T-valve/angle valve, screws, anchors, etc., complete in all respects as per direction of Engineer-in-Charge. Make: Jaquar, Hindware or equivalent approved by Engineer-in-Charge. |
| 224 | Providing, laying, and jointing of UPVC SCH 40 pipe of 20 mm nominal diameter (¾\") for cold water supply, including necessary fittings such as elbows, tees, sockets, reducers, solvent cement, clamps, and testing complete as per specifications and as directed by Engineer-in-Charge. |
| 225 | Providing, laying, and jointing PVC SWR (Soil, Waste & Rainwater) pipes conforming to IS 13592, 75 mm nominal diameter, including all necessary fittings such as bends, tees, offsets, access doors, clamps, solvent cement, etc., complete in all respects as per specifications and as directed by the Engineer-in-Charge. |
| 226 | Providing and fixing PVC SWR P-Trap of size 110x110 mm, conforming to IS 14735, suitable for soil and waste drainage applications, including jointing with solvent cement, fixing with required accessories like rubber gaskets, clamps, and making connection with drain pipe, complete in all respects as per specifications and direction of Engineer-in-Charge. |
| 227 | Providing and fixing 2-Way Bib Cock with wall flange it\"s accessories. |
| 228 | Providing and fixing Angular Stop Cock with wall flange it\"s accessories. |
| 229 | Providing and fixing Gunmetal non-return (check) valve, fullway type with wheel operation, of size 50 mm dia, ISI-marked, with screwed/ flanged ends (as per site requirement), including all accessories, jointing materials (rubber gasket, bolts, nuts, washers, PTFE tape), testing for leakage, and fixing in position complete as per direction of Engineer-in-Charge. |
| 230 | Providing laying and jointing PVC SWR pipes IS 13592 for Drain - 50 mmdia it\"s accessories. |
| 231 | Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. |
| 232 | Main Fire Hydrant Pump- Electric Motor Driven:SITC of: Back pull out type -Single Stage, Self Mriming, Centrifugal Pump for Main Fire Pump with Electric Motor, Base frame and Couplings.MOC:-Casing-CI, Impeller- Bronze, Shaft- SS 410, Sleeve-SS410.Flow Capacity: 2280 LPMHead: 65 mtrSpeed: 2900 ApproxPump shall be capable of furnishing not less than 150% of rated capacity at a head not less than 65% of rated head The shut off head shall not exceed 120% of rated head.UOM:-Price Per Complete set of Pump + Motor + Accessories.Note:-01. Minor civil work like tank hole/ Core Cutting etc. are in bidders scope.Location: In Pump RoomMake: Kirloskar / Lubi |
| 233 | Jockey Fire Pump- Electric Motor Driven:SITC of:Back Pull-out End Suction Type -Single Stage, Self Priming, Centrifugal Pump for Jockey Fire Pump with Electric Motor, Mechanical Seal, Base-frame and Couplings.MOC:-Casing-CI, Impeller- Bronze, Shaft- SS 410, Sleeve-SS410.Flow Capacity: 180 LPMHead: 65 mtrSpeed: 2900 ApproxPump shall be capable of furnishing not less than 150% of rated capacity at a head not less than 65% of rated head The shut off head shall not exceed 120% of rated head.UOM:-Price Per Complete set of Pump + Motor + Accessories.Note:-01. Minor civil work like tank hole/ Core Cutting etc. are in bidders scope.Location: In Pump RoomMake: Kirloskar / Lubi |
| 234 | Standby Fire Pump- Diesel Engine DrivenSITC of: Diesel Engine driven Standby Pumping System complete with,diesel engine, Back Pull-out Type Single Stage, Self Priming, Centrifugal Pump, Couplings & Base-frame:MOC:- Pump Casing-CI, Impeller- Bronze, Shaft-SS410, Sleeve- SS410.Flow Capacity: 2280 LPMHead: 65 mtrSpeed: 2900 LPMDiesel Engine includes 100 ltr diesel tank, battery, battery charger, engine oil and coolant.UOM:-Price Per Each Set.Note:-01. Minor civil work like tank hole/ Core Cutting etc. are in bidders scope.Location: In Pump RoomMake: Kirloskar / Lubi |
| 235 | Fire Pump Control Panel- Auto and Manual Type. Supply, Installation and Testing of:Electric Control Panel for Electric Motor Driven Main Fire Pump, Sprinkler Pump and Jockey Fire Pump. all pumps can be Start Automatically (by Pressure Switch) & Manually.Design As per the Detail Specifications given.UOM:-Price Per Set.Location: In Pump RoomMake: Kirloskar / Lubi |
| 236 | Air Vessel:SITC of Pressurized Air Vessel f Size 450 mm Dia x 2000 mm long fabricated from 10 mm thick MS Plate with 25 mm drain valve, air release valve with ball valve on top and isolation valve. |
| 237 | Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for1.1 KV. to be laidon wall FRLS type with necessary clamps or in existing trench/ pipe of following size of cables - 3.5 core 70 Sq. mm |
| 238 | Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables.- 3.5 core 70 Sq. mm |
| 239 | Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. - 70 Sq.mm. |
| 240 | Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for1.1 KV. to be laidon wall FRLS type with necessary clamps or in existing trench/ pipe of following size of cables - 4 core 16 Sq. mm |
| 241 | Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables.- 4 core 16 Sq. mm |
| 242 | Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. - 16 Sq.mm. |
| 243 | Pressure Gauge with Siphon Tube and Cock.Supply, Installation and Testing of:Pressure Gauge with Siphon Tube and Cock.MOC:-4” Dial- Glycerin filled- Stainless Steel Body Pressure Gauge with GI Siphon Tube andBrass Cock.Size:-Dial: 4” (100 mm)Range: 0 – 16 Bar (kg/cm2)UOM:-Price Per Unit |
| 244 | Pressure Switch with Siphon Tube and Cock.Supply, Installation and Testing of: Pressure Switch with Siphon Tube and Cock.Size:- Range suitable for System Design Pressure.UOM:-Price Per Unit |
| 245 | Pipe Laying.Supply, Fabrication, Installation, Hydro Testing & Painting of Under Ground Pipe.With necessary Pipe Fitments (Flanges, Bands, Socket etc.),MS Support/Clamps/Hangers, Coating etc.Hardware (Gaskets, Nut-Bolts, Paint etc.),Consumables (Welding Rod, etc.) and Labour Charge.Quality: GI, C-Class (Heavy).Paint: UOM:-Price Per Running Meter Size: 200 mm |
| 246 | Pipe Laying.Supply, Fabrication, Installation, Hydro Testing & Painting of Under Ground Pipe.With necessary Pipe Fitments (Flanges, Bands, Socket etc.),MS Support/Clamps/Hangers, Coating etc.Hardware (Gaskets, Nut-Bolts, Paint etc.),Consumables (Welding Rod, etc.) and Labour Charge.Quality: GI, C-Class (Heavy).Paint: UOM:-Price Per Running MeterSize: 150 mm |
| 247 | Pipe Laying.Supply, Fabrication, Installation, Hydro Testing & Painting of Under Ground Pipe.With necessary Pipe Fitments (Flanges, Bands, Socket etc.),MS Support/Clamps/Hangers, Coating etc.Hardware (Gaskets, Nut-Bolts, Paint etc.),Consumables (Welding Rod, etc.) and Labour Charge.Quality: GI, C-Class (Heavy).Paint: UOM:-Price Per Running MeterSize: 100 mm |
| 248 | Pipe Laying.Supply, Fabrication, Installation, Hydro Testing & Painting of Above Ground Pipe.With necessary Pipe Fitments (Flanges, Bands, Socket etc.),MS Support/Clamps/Hangers etc.Hardware (Gaskets, Nut-Bolts, Paint etc.),Consumables (Welding Rod, etc.) and Labour Charge.Quality: GI, C-Class (Heavy).Paint: UOM:-Price Per Running Meter Size: 200 mm |
| 249 | Pipe Laying.Supply, Fabrication, Installation, Hydro Testing & Painting of Above Ground Pipe.With necessary Pipe Fitments (Flanges, Bands, Socket etc.),MS Support/Clamps/Hangers etc.Hardware (Gaskets, Nut-Bolts, Paint etc.),Consumables (Welding Rod, etc.) and Labour Charge.Quality: GI, C-Class (Heavy).Paint: UOM:-Price Per Running Meter Size: 150 mm |
| 250 | Pipe Laying.Supply, Fabrication, Installation, Hydro Testing & Painting of Above Ground Pipe.With necessary Pipe Fitments (Flanges, Bands, Socket etc.),MS Support/Clamps/Hangers etc.Hardware (Gaskets, Nut-Bolts, Paint etc.),Consumables (Welding Rod, etc.) and Labour Charge.Quality: GI, C-Class (Heavy).Paint: UOM:-Price Per Running MeterSize: 100 mm |
| 251 | Pipe Laying.Supply, Fabrication, Installation, Hydro Testing & Painting of Above Ground Pipe.With necessary Pipe Fitments (Flanges, Bands, Socket etc.),MS Support/Clamps/Hangers etc.Hardware (Gaskets, Nut-Bolts, Paint etc.),Consumables (Welding Rod, etc.) and Labour Charge.Quality: GI, C-Class (Heavy).Paint: UOM:-Price Per Running Meter Size: 80 mm |
| 252 | Pipe Laying.Supply, Fabrication, Installation, Hydro Testing & Painting of Above Ground Pipe.With necessary Pipe Fitments (Flanges, Bands, Socket etc.),MS Support/Clamps/Hangers etc.Hardware (Gaskets, Nut-Bolts, Paint etc.),Consumables (Welding Rod, etc.) and Labour Charge.Quality: GI, C-Class (Heavy).Paint: UOM:-Price Per Running Meter Size: 65 mm |
| 253 | Pipe Laying.Supply, Fabrication, Installation, Hydro Testing & Painting of Above Ground Pipe.With necessary Pipe Fitments (Flanges, Bands, Socket etc.),MS Support/Clamps/Hangers etc.Hardware (Gaskets, Nut-Bolts, Paint etc.),Consumables (Welding Rod, etc.) and Labour Charge.Quality: GI, C-Class (Heavy).Paint: UOM:-Price Per Running Meter Size: 50 mm |
| 254 | Pipe Laying.Supply, Fabrication, Installation, Hydro Testing & Painting of Above Ground Pipe.With necessary Pipe Fitments (Flanges, Bands, Socket etc.),MS Support/Clamps/Hangers etc.Hardware (Gaskets, Nut-Bolts, Paint etc.),Consumables (Welding Rod, etc.) and Labour Charge.Quality: GI, C-Class (Heavy).Paint: UOM:-Price Per Running MeterSize: 40 mm |
| 255 | Pipe Laying.Supply, Fabrication, Installation, Hydro Testing & Painting of Above Ground Pipe.With necessary Pipe Fitments (Flanges, Bands, Socket etc.),MS Support/Clamps/Hangers etc.Hardware (Gaskets, Nut-Bolts, Paint etc.),Consumables (Welding Rod, etc.) and Labour Charge.Quality: GI, C-Class (Heavy).Paint: UOM:-Price Per Running Meter Size: 25 mm |
| 256 | Gate /SluiceValveSupply, Installation and Testing of:Gate/ Sluice (Rising Spindle -Screw & Yoke Type) Valve with necessary pipe fitments, hardware and consumables.MOC:-Body: Cast Iron, Disk: Cast Iron, Seat: Nitrile, Stem: SS. (With Flange Ends).Standard: ISI Marked.UOM:-Price Per Each No. Size: 200 mm |
| 257 | Gate /SluiceValveSupply, Installation and Testing of:Gate/ Sluice (Rising Spindle -Screw & Yoke Type) Valve with necessary pipe fitments, hardware and consumables.MOC:-Body: Cast Iron, Disk: Cast Iron, Seat: Nitrile, Stem: SS. (With Flange Ends).Standard: ISI Marked.UOM:-Price Per Each No. Size: 150 mm |
| 258 | Gate /SluiceValveSupply, Installation and Testing of:Gate/ Sluice (Rising Spindle -Screw & Yoke Type) Valve with necessary pipe fitments, hardware and consumables.MOC:-Body: Cast Iron, Disk: Cast Iron, Seat: Nitrile, Stem: SS. (With Flange Ends).Standard: ISI Marked.UOM:-Price Per Each No. Size: 80 mm |
| 259 | Check ValveSupply, Installation and Testing of:Check Valve (Ball type or Swing type) with necessary pipe fitments, hardware and consumables.MOC:-Body: Cast Iron (With Flange Ends).Standard: ISI Marked.UOM:-Price Per Each No.Size: 150 mm |
| 260 | Check ValveSupply, Installation and Testing of:Check Valve (Ball type or Swing type) with necessary pipe fitments, hardware and consumables.MOC:-Body: Cast Iron (With Flange Ends).Standard: ISI Marked.UOM:-Price Per Each No. Size: 80 mm |
| 261 | Check ValveSupply, Installation and Testing of:Check Valve (Ball type or Swing type) with necessary pipe fitments, hardware and consumables.MOC:-Body: Cast Iron (With Flange Ends).Standard: ISI Marked.UOM:-Price Per Each No. Size: 50 mm |
| 262 | Butterfly ValveSupply, Installation and Testing of:Butterfly Valve with necessary pipe fitments, hardware and consumables.MOC:-Body: Cast Iron, Disk: SS, Seat: Nitrile.UOM:-Price Per Each No.Size: 150 mm |
| 263 | Butterfly ValveSupply, Installation and Testing of:Butterfly Valve with necessary pipe fitments, hardware and consumables.MOC:-Body: Cast Iron, Disk: SS, Seat: Nitrile.UOM:-Price Per Each No. Size: 100 mm |
| 264 | Butterfly ValveSupply, Installation and Testing of:Butterfly Valve with necessary pipe fitments, hardware and consumables.MOC:-Body: Cast Iron, Disk: SS, Seat: Nitrile.UOM:-Price Per Each No. Size: 80 mm |
| 265 | Butterfly ValveSupply, Installation and Testing of:Butterfly Valve with necessary pipe fitments, hardware and consumables.MOC:-Body: Cast Iron, Disk: SS, Seat: Nitrile.UOM:-Price Per Each No. Size: 50 mm |
| 266 | Strainer.Supply, Installation and Testing of: Y Type Strainer with necessary pipe fitments, hardware and consumables.MOC:-Body: Cast Iron, Mesh: SS-304.Working Pressure: 10 BarUOM:-Price Per Each No. Size: 200 mm |
| 267 | Air Release Valve- 25 mmSupply, Installation and Testing of:Air Release Valve Check Valve with necessary pipe fitments, hardware and consumables. MOC:-Body: Gunmetal / SS. UOM:-Price Per Each No. |
| 268 | Fire Hydrant Landing Valve (Stainless Steel (SS-304), ISI Marked):Supply, Installation and Testing of:Fire Hydrant Landing Valve with necessary pipe fitments, hardware and consumables.MOC:-Body: Stainless Steel (SS-304), Working Parts: Stainless Steel (SS-304), Coupling: Stainless Steel (SS-304), Standard: -ISI Marked.Size:-63 mm (Flange End: NB 75 mm, PCD 160 mm)UOM:-Price Per Each No. |
| 269 | Fire Hose Pipe (Delivery Hose)- 63 mm x 15 mSupply, Installation and Testing of:Fire Hose with Hose Couplings.RRL (ISI Mark- Type A) Fire Hose.Hose Couplings: ISI Marked Stainless Steel.With SS Wire Binding.Standard: - ISI Marked & TAC Approved Hose.Size:-63 mm dia x 15m long Hose.UOM:-Price Per Each Set. |
| 270 | Cabinet For Fire Hose (Hose Box)- Double TypeSupply, Installation and Testing of:Fire Hose Cabinet (Hose Box) suitable to accommodate 02 no. of 15 m long fire hoses and 01 no. of nozzle. With Lock-n-key facility. Wall Mounting Design.MOC: 16 Gauge MS Box with Powder CoatingStandard: - As per Guidelines.Size:- Suitable for 02 nos. of 15 m long hoses.UOM:-Price Per Each No. |
| 271 | Fire Hose Nozzle- Short Branch Pipe Nozzle.Supply, Installation and Testing of:Short Branch-pipe Nozzle.MOC: Stainless Steel (SS-304).Standard: ISI Marked, Heavy Quality.Size:- 63 mm X 20 mmUOM:-Price Per Each No. |
| 272 | Fire Hose Reel Set (ISI)-19 mm x 30 m -Rubber Hose.Supply, Installation and Testing of:Fire Hose Reel Set with necessary pipe fitments, hardware and consumables.MOC:-Drum: 16 G Powder Coated MS,Hose: 19 mm X 30 m heavy-duty RUBER hose.Shut-off Nozzle: SS-304.With Control Valve: SS- 25mm Ball Valve.Standard: ISI Marked. Heavy Quality.Size:-19 mm dia x 30m long Hose.UOM:-Price Per Each No. |
| 273 | Fire Service In-let (In-let Connection for Fire Brigade)-4 Way Type.Supply, Installation and Testing of:Fire Service Inlet with necessary hardware and consumables.MOC:-Body: Heavy-duty CI.Couplings/NRV: Gunmetal.Standard: -Made As per IS Standard- Heavy duty quality.Size:-Couplings: 63 mm, 150 mm E-table Flange End.UOM:-Price Per Each No. |
| 274 | Sprinkler Head/ Nozzle.Supply, Installation and Testing of:K 5.6 Pendent type Standard Response Sprinkler rating of57 deg.C. with required accessories.MOC:-BrassStandard: UL ListedSize:-15 mm (1/2”)UOM:-Price Per Each No. |
| 275 | Sprinkler Drop Pipe: Supply, Installation and Testing of: Sprinkler Drop Pipe with necessary pipe fitments.Standard: UL ListedUOM:-Price Per Each No.Make: Safex/Tyco/ UL Listed |
| 276 | Flow SwitchSupply, Installation and Testing of: Flow Switch with necessary pipe fitments, hardware and consumables.UOM:-Price Per Each No.With all wiring/ cabling up to control panel and all electrification. |
| 277 | Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copperconductor for1.1 KV. to be laidon wall FRLS type with necessary clamps or in existingtrench/ pipe at road crossing or floorof following size of cable.(a) 3 core 2.5Sq. mm |
| 278 | Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables.(a) 2 to 4 core 2.5 Sq. mm |
| 279 | Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. (A) 1.5/ 2.5/4/6 Sq.mm |
| 280 | Providing, fixing, testing and commissioning of Annunciator panel for flow control switch, providing Audio/Visual indicating of actuation of automatic sprinkler system for each zone complete as per specifications with provision for 30 zones (22 working and 8 spare for future).\"Indication of zone fire, \"Indication of zone fault, \"Fire/Fault hooter, \"Alarm cancel for fire/fault, \"Battery for emergencyMake: CPRI Approved |
| 281 | Providing and fixing, testing and commissioning of Drainning Valve 50mm dia with by pass drain connection as required. |
| 282 | Providing and fixing, testing and commissioning of CO2 type Fire Extinguisher of capacity 22.5 kg filled with Co2 Gas as per IS 15222 with controll discharge mechanism fitted with Hose, Horn & TROLLEYconfirms to IS 2878 bearing ISI mark. Co2 Cylinder as per IS 7285. |
| 283 | Fire Extinguisher- ABC Powder type, 6 kg.Supply, Installation and Testing of:ABC Powder Fire Extinguisher necessary hardware and consumables.Stored Pressure Mechanism.Charged with MAP-50 % (ABC) Dry Powder.With wall mounting clamp.Size:-6 kg Powder.UOM:-Price Per Each No. |
| 284 | Fire Extinguisher- CO2 Gas type, 4.5 kg.Supply, Installation and Testing of:CO2 Gas Fire Extinguisher with necessary hardware and consumables.Standard: - Confirming to IS: 15683-2006 with ISI Mark.Size:-4.5 kgUOM:-Price Per Each No. |
| 285 | Supplying FIREbucket round bottom of9 litres capacity made out of 24 gauge G.I. sheet with extra handle at bottom duly painted white inside andRed out side with FIRE mark,filled with dry-sand and kept on existing stand provided or hung on wall hook. |
| 286 | Supplying and erecting floor mounting stand for keeping four nos. of FIRE buckets comprising 1500 mm in length, 900 mmheight frame made out of 30mm X30 mm X 4 mm angle iron with cross supports for legs, welded with 4 hooks and duly painted with one coat of red lead and two coats of approved enamelled silver paint. |
| 287 | Safety Signage- Night Glow Type:SIRC of: Single Side Printed Night Glow (Glow in Dark ) Safety Signage. Printed on PVC sticker sheet and pasted on 3-5 mm thick PVC foam sheet.Size: 10” X 10”. |
| 288 | RCC Hume Pipe:Providing and Laying NP3 RCC Hume Pipe of 300 mm at road crossing including excavation for pipe line trenches incl. all safety provisions using site rails and stacking excavated stuff up to a lead of 90 mts. cleaning the site etc. complete for lifts and strata as specified upto 1.5 mt. Depth. Also refilling the pipeline trenches incl. ramming, watering consolidating desposal of surplus stuff as directed within a radius of 3 K.M. |
| 289 | Approval of Fire Hydrant & Entire Fire Protection System from Local Fire Authority and any other relevant statutory authority at initial and various other stages of work, including preparation of report/drawings as per fire authority requirement. Contractor shall include cost of all liason work which are not explicitly mentioned above but are mandatory to have fire authority approval (any statutory charges will be paid extra). |
| 290 | PVC pipe 90mm-6 kg/cm2 |
| 291 | PVC pipe 75mm-6 kg/cm2 |
| 292 | PVC pipe 63mm-6 kg/cm2 |
| 293 | PVC pipe 50mm-6 kg/cm2 |
| 294 | PVC pipe 40mm-6 kg/cm2 |
| 295 | Earthworkexcavationand refilling 300x450mm |
| 296 | Providing & fixing of PGP ULTRA, Pop-up ROTOR sprinklerhaving variableadjustable arc (50 to 360 degrees)nozzle capable of covering 4.9m -14.0 m at 2.5 Bars with discharge rate of 0.02- 0.891Lps.The Rotor body, stem, nozzle and screen shall be constructed of heavy-duty, ultraviolet resistant plastic withsmall exposed cover. |
| 297 | Providing & Fixing of SJ- 712, 3/4\" Pop up Connecting Four Elbow Swing joint Assembly.The fittings shall be made of UV resistant thermo plastic. |
| 298 | Providing and fixing ofPP service saddle ofvarying size.3/4\" |
| 299 | Supplyand fixing of flexible Blank tubingand resistance to UV damage and algae growth black incolour 16 mm size. With all fittings and accessories.( Dripline 16 mm 50 cm 3.8 lphinline lateral) |
| 300 | Supplyand fixing of flexible Blank tubingand resistance to UV damage and algae growth black incolour 16 mm size. With all fittings and accessories.( Plain Dripline 16 mm plain lateral) |
| 301 | Supplyand fixing of PC dripers8lph |
| 302 | Supply and FixingRod Comes Pre -Bent or plastic lateral stack to Staple DistributionTubing , DripLine to FinishedGrade. |
| 303 | Providing and fixing of PVC Ball Valve,SECURITYy pivot to maintain lever in space,double water tight joint,direct injection stem non mechanical ,with a base which permits maximum penetration into the valve of size 63mm. |
| 304 | Providing and fixing of PVC Ball Valve,SECURITYy pivot to maintain lever in space,double water tight joint,direct injection stem non mechanical ,with a base which permits maximum penetration into the valve of size 50mm. |
| 305 | Providing & fixing of IsolationValvein mainlinefor bypass and flow diversion of approved quality |
| 306 | Providing & fixing of a double acting 1\"Air release valve,The Air release valve shall be capable of both releasing and admitting air from and into the line. The working pressure shall be 5 bar. Including service saddle and riser assembly. |
| 307 | Providing & fixing of 12\" Rectangular Valve Box withgreenlid and corrugated structure with unique shovelaccess slot and bolt hole knockout |
| 308 | Providing & fixing of 10\"Roundbox withgreenlid and corrugated structure with unique shovelaccess slot and bolt hole knockout |
| 309 | Providing & fixing of 6\"Roundbox withgreenlid and corrugated structure with unique shovelaccess slot and bolt hole knockout |
| 310 | Providing & fixing of Brass Quickcoupling valve made up ofsolidbrass with locking covercorrosion resistant and stainless steel spring.Including service saddle and riser assembly. |
| 311 | Providing & fixing of Brass Key threads into top of QCV to provide water access And Brass Swivel Elbow |
| 312 | Providing & Fixing ofSand Filter 40m3/hr , MANUAL |
| 313 | Providing & Fixing ofDISC FILTER- with capacity matching pump design flowhaving an suitableinlet connections , to create a helical effect in the incoming water ,spinning particulate in suspension away from the filtering element and so minimizing cleanings frequency ,3/4\" outlet for flushing at bottom of filter & maximum working presure of 10 Bars. with pressure gauge. |
| 314 | Providing & Fixing of(Monoblock/Openwell submersible) pumpset of having discharge 6.5 lps@48 mtrhead .suitable for pumpset having panel boxand fixed alongwith following accessories starter ,start / stop push buttons , Ammeter,Voltmeter , Indicating lamps, MCB ,with cable, etc. |
| 315 | Providing and fixing ofcontrol panelsuitable for pumpset having panel boxand fixed alongwith following accessories starter ,start / stop push buttons , Ammeter,Voltmeter , Indicating lamps, MCB ,with cable, etc. |
| 316 | Providing & Fixing of,Suction ,Delivery & Header Pipe |
| 317 | Providing & fixing of controlValve /Butterfly Valvein mainlinefor bypass and flow diversion of approved quality 3\" |
| 318 | Providing & fixing of Non Return Valveto prevent back flow 3\" |
| 319 | Providing and fixing of Pressure Release Valve 2\" |
| 320 | Supply and fixing of Direct burial 14 AWG x 2C cablefor two way communication betweencontroller and decoders |
| 321 | PVC conduit Pipe complete32 mm |
| 322 | Supply and fixing of ICC2 MEDIUM CONTROLLERSWITH EZDM EZ Decoder Output Moduleinternal transformer control system , cycle +soak, Raindelay, SOLARSYNC Mini weather station,controlling upto 1 mastervalve with diagnostic feature in wire shorttest ,voltage test at stations, standard accessories complete |
| 323 | Supply and fixing of EZ1 1 Station Decoder |
| 324 | Supply and fixing of 1.5\"Solenoid globeValves with fabric reinforced diaphramand rugged PVC construction,compatible with and slow closing to prevent water hammer,pressure rating upto 10 bar with 24AC solenoid, withprovision to attachPressure Regulator |
| 325 | Supply and fixing of 2\"Solenoid globeValves with fabric reinforced diaphramand rugged PVC construction,compatible with and slow closing to prevent water hammer,pressure rating upto 10 bar with 24AC solenoid, withprovision to attachPressure Regulator |
| 326 | Supplyand fixing ofdirect bury -on wireconnector withstrain relief , with waterproof silicon sealant. |
| 327 | Supply and fixingof SOLARSYNC COMPATIBLE WITH PRO-C, ICC AND I-CORE CONTROLLERS, COMES COMPLETE WITH SENSOR PLATFORM AND CONTROLLER INTERFACE, AUTOMATICALLY RESPONDS TO LOCAL WEATHER CHANGES . |
| 328 | Supply and fixingofACCU-SYNC-ADJ ACCU-SYNC PRESSURE REGULATOR, ADJUSTABLE PRESSURE MODEL 1.4–7 BAR (20–100PSI), WORKS WITH ANY HUNTER VALVE |
| 329 | Supply and fixingof copper grounding rod, clamps, charcoal and all requisite accessories complete |
| 330 | Supplyand fixing of Pump relay24 ACPLA relay |
| 331 | Providing, supplying, installing, testing and commissioning a Very Narrow Aisle (VNA) forklift with Lithium-Ion Battery. The forklift shall be suitable for lifting pallets up to 5000 mm height and designed for tri-lateral stacking operations.Technical data EKX 410-5162. Technical Requirements2.1 Lift ParametersLift height: 5000 mmRetracted mast height: approx. 3600–3705 mmExtended mast height: approx. 7550 mmFree lift (Triplex mast): 250–345 mm2.2 Rated Load Capacity: 1400 kg2.3 Machine WeightApprox. 5515 kg to 7900 kg (including battery)3. Performance RequirementsTravel speed: 10.5–12 km/hrLift speed: 0.4–0.6 m/sLowering speed: 0.4–0.5 m/sLateral reach: 1300 mmTurning radius: 2122–2502 mmService brake: RegenerativeParking brake: Electric sprung loaded4. Battery SystemRequired battery type: Lithium-IonVoltage capacity equivalent to OEM recommended ratings:48 V, 750–930 Ah (for EKX 410–412)Technical data EKX 410-516Lithium-Ion charger and Battery Management System to be included.5. Fork SystemFork size:40 × 120 × 1200 mm (EKX 410–412)Fork carriage class: 2B6. Wheels and TyresTyre type: BesthaneFront and rear tyre sizes as per model range Wheel configuration: 2 front wheels / 1 rear wheel (driven)7. Operator Cabin and SafetyOverhead guard height: 2550 mmElevated stand height: 3930 mmStandard safety features:Emergency stopOperator presence switchLoad monitoringAutomatic speed reduction with mast elevationAudible and visual warning systemsNoise level: 64 dB(A)8. Guidance System RequirementMachine shall be compatible with rail guidance or wire guidance as per site requirement.9. Documentation and WarrantySupplier shall provide:Operation manualMaintenance manualTraining for operatorsStandard OEM warranty (minimum 24 months)10. Installation and Commissioning ScopeDelivery to siteAssembly and installationBattery installation and charger setupIntegration with aisle guidanceComplete testing and trial runHandover and training11. Unit of MeasurementNos. (Each)Make : Jungheinrich model EKX 410–516 series or Equivalent as approved by Chief-Engineer |
| 332 | Project scope: Supply, delivery, erection, alignment, grouting & testing of selective pallet racking system — 3 tiers (i.e. ground + two elevated levels), designed for 1,000 kg per pallet location unless noted otherwise. Work includes shop drawings, structural calculations, protective finishes, accessories, safety devices, labeling, and warranty.SELECTIVE PALLET RACKING (2000 PALLETS, 3 TIERS)Configuration:Pallet size: 1200 mm × 1000 mmStorage capacity: 2000 pallet positionsRacking type: Selective pallet racking, single-deepLevels: 3 tiers (Ground + 2 beam levels)Bay configuration: 2 pallet positions per level per bayPallet positions per bay: 6Total bays required: 334 bays1. GENERAL REQUIREMENTSContractor shall design, supply, deliver, erect and commission a complete pallet racking system suitable for storing 2,000 pallets of 1,000 kg each.All structural components shall comply with EN 15512 / FEM 10.2.02 / ANSI MH16.1 and applicable Indian standards including IS 800 and IS 2062.Structural steel grade: IS 2062 E350 or equivalent.All racking must be designed to safely support:1,000 kg working load per pallet,2,000 kg per beam level (2 pallets × 1,000 kg),Proof load test at 1.25 × working load.Allowable deflection limits shall comply with L/200 or stricter.Contractor shall submit detailed shop drawings, load calculations, and a Bill of Materials for approval before fabrication.Racking layout must allow clear operating aisles suitable for the selected MHE2. SYSTEM CONFIGURATIONPallet type: Standard 1200 × 1000 mmPallet orientation: 1200 mm along bay spanBay span: approx. 2400 mm (to accommodate two 1200 mm pallets)Racking depth: 1000 – 1100 mm based on pallet depthLevels:Ground level1st beam level2nd beam level(Total 3 levels / 3-tier)Pallet positions per bay:2 pallets per level × 3 levels = 6 pallet positionsTotal bays required:2000 ÷ 6 = 333.33 → 334 bays3. MATERIAL SPECIFICATION3.1 Upright Frames (2 per bay)Cold/Roll formed steel upright sections manufactured from IS 2062 grade steel.Upright thickness: minimum 2.5 mm or higher as per structural design Frames shall include:Upright columnsHorizontal and diagonal bracingBase plates (minimum 6 mm thick)Upright perforations at 50–75 mm pitch.Finish: powder-coated (minimum 80 microns) 3.2 Load Beams (3 beam pairs per bay = 3 levels)Each beam level designed for 2,000 kg UDL (2 pallets × 1000 kg).Roll-formed box beam / step beam / open section as approved.Beam connectors with locking pins for positive locking.Beam lengths approx 2400 mm (for two pallets).Finish: powder-coated 3.3 Pallet Support Bars / DeckingDecking for 2000 pallet positions:Estimated decking area ≈ 2000 × 1.2 sqm ≈ 2,400 sqmOptions (one of the following):Wire mesh deckingEach decking panel shall support 1000 kg per pallet footprint.3.4 Fasteners & AnchorsHigh-tensile bolts, nuts, washers as per design.Base plate anchors: mechanical wedge anchors or chemical anchors per slab condition.Anchors must meet torque and pull-out strength requirements.3.5 Safety ProtectionColumn guards for all exposed uprights.End-of-aisle protectors for all row ends.Row spacers if double rows are provided.Safety locking pins for all beams.Load signage boards for every bay.4. INSTALLATION SPECIFICATION4.1 Pre-InstallationSite measurement verification.Submission & approval of shop drawings.Verification of warehouse slab capacity for point loads.4.2 Installation WorkErection of upright frames, plumbed within ±10 mm tolerance.Installation of beam pairs at approved elevations.Installation of decking, pallet supports, column guards, signage.Anchoring of all uprights to floor using approved anchors.Use of non-shrink grout (if required).4.3 FinishingTouch-up of damaged coating.Cleaning and removal of packaging.Final alignment check and tightening to torque.5. TESTING & COMMISSIONINGPerform proof load test on selected bays at 1.25 × rated load (i.e., 1250 kg per pallet position).Submit load test report with recorded deflections.Replace any component showing excessive deflection or failure.Provide load charts, maintenance manual, as-built drawings.6. BILLING / UOMMeasurement and billing to be done as PER BAY criteria 7. SUMMARY OF QUANTITIES Total Bays Required334 baysBeam Pairs Required334 bays × 3 beam levels = 1,002 beam pairsUprights RequiredConservative BOQ: 334 bays × 2 uprights = 668 uprightsOptimized shared-upright layout: ~335 uprights (if placed in continuous rows)Decking Requirement≈ 2,400 sqm (based on pallet footprint)AccessoriesColumn guards for all exposed uprightsEnd-of-aisle protectors (as per number of rows)Beam locking pins (1 set per beam pair)Anchors for every upright base plateMake : Godrej or Equivalent as approved by Chief Engineer |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
