|
| 1 | M&L for PCC type C1,1:3:6using 20mm graded crushed stone agg,in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed. |
| 2 | M&L for R.C.C, Nominal mix of 1:1.5:3 using 20 mm graded stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves etc all as specified and directed. |
| 3 | Supply only integral water proofing compound liquid grade conforming to IS-2645 complete all as specified and directed. (Pidiproof of Dr.fixit or equivalent) |
| 4 | M&L for brickwork with old size fly ash bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed. |
| 5 | M&L for brickwork with old size fly ash bricks, straight or curved on plan to any radius as in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed. |
| 6 | M&L for Cutting chases, pinning in brick walls,making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills,sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring,etc.and making good, cutting not exc 10cm girth complete all as specified and directed. |
| 7 | Making good under cills or over arches, lintels and bressummers. including all pinning in cement mortar 1:4when necessary complete all as specified and directed. |
| 8 | M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed. |
| 9 | S&F 2nd class hard wood 35 mm thick made glazed and skeleton shuttersopen rebated and prepared to rceieve glass, gauze,etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, size of members of shutters as spfd in SSR Part-1, Section 8, clause 8.24 (a) kiln seasoned and chemically pressure treated complete all as specified and as directed |
| 10 | S&F 35mm thick factory made flush shutter, solid core construction with block board core and plywood face panels, commercial type on both sides kiln seasoned and chemically pressure treated complete all as specified and directed. |
| 11 | Taking down chowkat or frame with shutter (without taking off shutter from the frame) area not exc. 1.5sqm each, including cutting holes for removing the hold fast,making good disturbed surfaces and removing materials from site of work complete all as specified and directed. |
| 12 | Taking down chowkat or frame with shutter (without taking off shutter from the frame) exc. 1.5 sqm and n.exc 4 sqm each, including cutting holes for removing the hold fast, making good disturbed surfaces and removing materials from site of work complete all as specified and directed. |
| 13 | S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heatm moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain/decorative colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement in the frame at site as per specification & drawing. etc complete all as specified and directed. |
| 14 | S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube in opening as per specification & drawingcomplete all as specified Make : Rajshree/Sintex/H2O solution.Note:-The door frame to be fixed to wall using 8 x 100 mm long anchor fasteners. |
| 15 | S&F 200mm aluminium anodised barrel tower bolts of extruded sectioncomplete all as specified and directed. |
| 16 | S&F 150mm aluminium anodised barrel tower bolts of extruded sectioncomplete all as specified and directed. |
| 17 | S&F 300 mm long aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) andfixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and direcetd. |
| 18 | S&F 75mm Butt hinges,medium weight, cold rolled mild steel,complete all as specified and directed. |
| 19 | S&F 150mm size aluminium handle cast typecomplete all as specified and directed. |
| 20 | S&F in repairs Harrison rails, mild steel, chromium plated with fixing brackets,stops, rollers etc of 25 mm bore complete all as specified and as directed |
| 21 | S&F in repairtubular towel rail 20mm dia type brass chrormium plated 600mm long between flanges complete all as specified and directed. |
| 22 | S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staplescomplete all as secified and as directed |
| 23 | M&L for MS framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors;ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165complete all as specified and directed. |
| 24 | M&L forTMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 25 | S&F Hard drawn steel wire fabric weight n.exc 4 Kg/Sqm cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia supplied and fixed in reinforcemnt complete all as specified and as directed |
| 26 | M&L forrolled sections as in main and cross beams, hip and jack rafters, purlins where connected to comman rafters and running railsfixed with angle cleats or other connecting plates conforming to Fe 410 W (Gde E-250) quality-A including welded to rafter,purlin complete all as specified and directed. |
| 27 | S&F Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed. |
| 28 | M&L for 1.25mm thickpressed steel door frame of size 165mm x 60mm with one or more rebates including necessary , hinges, lock strike plate, fixing lugsetc complete as specified. |
| 29 | M&L for anodised aluminium snap grid (SIZE-605x605MM) frame work for false ceiling complete all as specified and directed. |
| 30 | S&F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed. |
| 31 | S&F Pre- painted coloured trapezoidal profiled Galvalume/ Zincalume sheet with min thickness 0.50mm TCT confirming to IS - 513(AZ-150 GSM, Al Zn allay metalic coating with 550 Mpa yield stress as per AS-1397) as in roof covering/cladding towall, fixed with self tapping screws colour exterior coat of silicon modified polyster/BHP x RW paint system 20 micron top coat applied over 5 micron primer and 5 micron polyster back coat applied over 5 micron primer , all fixed with galvanized self drilling self tapping fastner (12-14 x 55 with EPDM seals) complete all as specified and directed. |
| 32 | S&F Pre- painted coloured plain sheet Galvalume/ Zincalume sheet with min thickness 0.50mm TCT confirming to IS - 513(AZ-150 GSM, Al Zn allay metalic coating with 550 Mpa yield stress as per AS-1397) as in roof covering/cladding towall, fixed with self tapping screws colour exterior coat of silicon modified polyster/BHP x RW paint system 20 micron top coat applied over 5 micron primer and 5 micron polyster back coat applied over 5 micron primer , all fixed with galvanized self drilling self tapping fastner (12-14 x 55 with EPDM seals) complete all as specified and directed. |
| 33 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings,heads, shoes, bends, swan-necks,etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories)complete all as specified and directed. |
| 34 | S&F 4mm thick non asbestos fiber cementbuilding boards, fixed or laid /inserted totimber /GI /Aluminium frame-work with screws complete all as specified and directed. |
| 35 | M&L for 15mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, win dow-cills, cooking plat forms and like in cement mortar (1:4) including point ing in white cement (1:2) us ing marble dust with admix ture of pigment to match with shade of granite over and including 20mm thick bedding layer in cement mortar 1:4 including grinding and polishing complete all as specified and directed. |
| 36 | M&L for 25mm thick cement concrete type B-1, 1:2:4 (using 20 mm graded crushed stone aggregates)as in flooring, finished the surface even and rough completeall as specified and directed. |
| 37 | Roughening the surfaces of old concrete floor by picking, sweeping cleaning and washing down with water to remove dust, etc complete all as specified and directed, |
| 38 | Dismantling of floor, hearth or wall tiling / Paving Blocks including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises etc complete all as specified and directed. |
| 39 | Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and directed. |
| 40 | M&L for sheet glass, 4mm thick, ordinary quality and glazing with oil putty in squares n exc. 0.50 Sqm each panecomplete all as specified and directed. |
| 41 | S&F 4.0mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sqm in each panecomplete all as specified and directed. |
| 42 | M&Lfor preparation of untreated new wood/wooden surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint (1st grade quality) over a coat of pink primer complete all as specified and directed. |
| 43 | M&L for one coats of synthetic enamel painton oldtreated steel surfaces of any description over 10cm in width or girthincluding preparation of surfaces complete all as specified and directed. |
| 44 | M&L for two coats of synthetic enamel paint over one coat of red oxideon new steel surfaces of any description over 10cm in width or girthincluding preparation of surfaces complete all as specified and directed. |
| 45 | S&F medium grade galvanized steel tubingwith all fittings & fixed complete to walls & ceiling or laid in floors 20 mm dia bore pipe (including in short length) complete all as specified anddirected. |
| 46 | S&F medium grade galvanized steel tubing with all fittings & fixed complete to walls & ceiling or laid in floors 25 mm dia bore pipe (including in short length) complete all as specified anddirected. |
| 47 | Taking down steel tubing & connections including cleaning for refixing serviceable pipe or removal balance pipe of 15 mm dia bore complete all as specified and as directed |
| 48 | Taking down steel tubing & connections including cleaning for refixing serviceable pipe or removal balance pipe of 20 mm dia bore complete all as specified and as directed |
| 49 | Taking up or down steel tubing and connections,including cleaning for refixing or removal to store bore of pipe 25 mm complete all as specified and as directed |
| 50 | S&F rotational moulded PVC water storage tank 1000 ltrs capacity conforming to IS-12701(1989) cylindrical vertical type double-layered with closed top (thereated) including inlet,outlet and wash out holes of approved make hoisted and fixed in position all as specified in SSR Part I etc completge all as specified and directed. |
| 51 | S&F in repairfancy type, chromium platedstop valve/ angle valvecast copper allow screw down high pressure with crutch or butterfly handle screwed both end form iron pipe or for union and fixed of size 15mm dia complete all as specified and directed. |
| 52 | S&F in repair fancy type with long shank and cup (concealed type) chromium plated stop valve cast copper allow screw down high pressure with crutch or butterfly handle screwed both end form iron pipe or for union and fixed of size 15mm dia complete all as specified and directed. |
| 53 | S&F 32mm waste fittings,brass,chromium plated for glazed ware sinks,basin,etc with long screwed shanks and fly-nuts,flange end bedded in red lead cement and other end fixed complete all as specified and directed. |
| 54 | S&F ball valves for 20mm bor dia of pipehigh pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0mm-210gms./25mm-455gms/ 40mm - 690 gms) complete all as specified and directed. |
| 55 | S&F grating doom 100mm dia of PTMT (minimum weightt 25 gm) for floor trap/nahani trap, complete all as specified and directed. |
| 56 | S&F in repair Towel Ring of PTMT fixed with and including Chromium plated brass screwsand wooden/plastic cleats (Minimum weight 90gms)complete all as specified and directed. |
| 57 | S&F in repair PVC connectionspipe ,15mm dia size with PTMT nuts of length 450mm complete all as specified and directed. |
| 58 | S&F 75mm PVC (SWR)pipes single socketed in any length with rubber ring joints fixed to wallscomplete all as specified and directed. |
| 59 | S&F 110mm PVC (SWR)pipes single socketed in any length with rubber ring joints fixed to wallscomplete all as specified and directed. |
| 60 | S&F 75mm bore PVC (SWR) bends with rubber ring joints any radius complete all as specified and directed. |
| 61 | S&F110mm bore PVC (SWR) bends with rubber ring joints any radius complete all as specified and directed. |
| 62 | S&F 110mm bore PVC (SWR), junction single, (Single T) equal or unequal complete all as specified and directed. |
| 63 | S&F 110mm bore PVC (SWR) vent cowl complete all as specified and directed |
| 64 | S&F 110mm bore PVC (SWR) `P\"or \"S\" trape complete all as specified and directed. |
| 65 | S&F in repair 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 66 | Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings,dressed stonework and precast concrete articles complete all as specified and directed. |
| 67 | Dismantling of stone slabs and tiles of any description or thickness in floors, approachs, dado/Partitionsetc complete all as specified and as directed. |
| 68 | Demolition of Concrete un- reinforced of any description and in any position not otherwise specifically provided for complete all as specified and directed. |
| 69 | Demolition of cement concrete (reinforced )ofRoofs,floors(otherthan groundfloors), beams, staircases, landing, chajjas and similar suspendedwork including removal complete all as specified and directed. |
| 70 | Dismantling timber scantlings 40 sqcm and over in section, in framed section any position like trusses, rafters, purlins etc. complete all as specified and directed. |
| 71 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 72 | Dimantling of Asbestos cement (corrugated,semi corrugated, etc.) sheets in roof coverings including ridges etc complete all as specified anddirected |
| 73 | Dismantlingwall and ceiling board( fiber, pulp, insulation, etc.) or insulation board/slab/ blankets, any thickness, including cover fillets complete all as specified and directed. |
| 74 | M&L for Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors,windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Zsections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dashfasteners of required dia and size, including necessary fittings and filling up the gaps at junctions, i.e. at top,bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle,Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, complete all as specified and directed. |
| 75 | S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, partitions,windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved makeonforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc.Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snapbeading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge.Note : (i) Weight of Aluminium sections as per actual or as per IS or as per Manufacturer which over is less, shall only be considered for payment.(ii) Cost of all the items/ accessories required for the entire completion of the work shall be deemed to be included in the quoted rate. However glass panes and particle board shall be measured and paid separately under respective items. (iii) The accessories requiredfor partition as per directions of Engineer-in-charge shall be provided but weight for the same shall not be considered and no extra cost will be paid. |
| 76 | M&L for 75mm thick PCC 1:3:6 type C1(Using 20mm graded stone aggregate) as in plinth protectionfinishedeven and smoothwithout using extra cement complete all as specified and directed. |
| 77 | M&L for Glazed ceramic tiles coloured 300mmx 450mm , 6 to 7 mm thick as in skirting / dado, set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10 mm thick in cement mortar 1:4 on fair faces of brick work or concrete surface etc complete all as specified andand as directed |
| 78 | M&Lfor Non Skidceramic tiles (coloured) 7 to 8 mm thick , (square / rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors etc, set and jointed in neat cement slurry and pointed with white or coloured cement to matchover and including screed bed or bedding layer 15 mm thick in cement mortar 1:6for laying floor finishes etc complete all as specified and directed |
| 79 | M&Lfor Non Skidceramic tiles (coloured) 7 to 8 mm thick , (square / rectangular) area of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm as in dado/skirting etc, set and jointed in neat cement slurry and pointed with white or coloured cement to matchover and including rendering layer 10 mm thick in cement mortar 1:4etc complete all as specified and directed |
| 80 | M&Lfor Non Skidceramic tiles (coloured) 7 to 8 mm thick , (square / rectangular) area of each tiles exceeding 0.18 sqm but not exceeding 0.38sqm as in floors etc, set and jointed in neat cement slurry and pointed with white or coloured cement to matchover and including screed bed or bedding layer 15 mm thick in cement mortar 1:6for laying floor finishes etc complete all as specified and directed |
| 81 | M&L for rendering 15 mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces and finishing surfaces even and smooth without using extra cement complete all as specified and directed. |
| 82 | M&L forrendering 15 mm thick in two layers 10mm +5mm in cement mortar 1:4 on external surfaces of brick work or concrete surfaces with using WPC finishing the surfaces even and smooth without using extra cement complete all as specified and directed.Note:- WPC will be measured and paid separately under respective item of this schedule. |
| 83 | M&L for 5mm thick rendering in cement mortar1:3 over/soffit of chajja/ceiling, finished surface even and smooth without using extra cement complete all as specified and directed. |
| 84 | M&L forpreparing of old plastered surface of wall by complete removal of existing treatment andapplying3mm thickwall care puttyon wall including preparation of surface and applying two coat of white or tinted oil bound distemper over one coat of alkali resistant priming paint etc complete all as specified and directed. |
| 85 | M&L fornewly plastered surface of wall and appying two coat of white or tinted oil bound distemper over one coat of alkali resistant priming primer including 03mm thick Birla/Asian wall care putty complete all as specified and as directed. |
| 86 | M&L for applying Two or more coats of 100% Premium acrylic emulsion paint on new surfaces having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed. |
| 87 | M&L for preparing of old existing treament and stopping of distempered and painted surfacesand applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over prepared surfaces complete all as specified and directed. |
| 88 | M&L for preparation of new undecorated surface of ceiling and applying two coats of white wash complete all as specified and directed. |
| 89 | Supply and laying of CPVC pipes outer diameter 20mm SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed. |
| 90 | S&F in repair bib tap fancy type cast copper alloy chromium plated with crutch or butterfly handle screwed down screwed for iron pipe or brass ferrule or fixed for 15 mm dia bore pipe complete all as specified and directed. |
| 91 | S&F in repair15 mm bore pillar taps fancy type (long neck) cast copper alloy with hot & cold mixturechromium plated screwed down high pressure with or without letter hot or could with long screwed and shanks and fly nuts screwed for iron pipes complete all as specified and as directed. |
| 92 | Suppy and fixing in repairs Vitreous China bowl urinal back or corner wall type, size of 465 x 355 x 265 mm white (minimum),with grating and union for discharge pipe (excluding flushing cistern, but including waste pipe) complete including providing and fixing plugs ,bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60 mm long brass screws pointing around urinal back in cement with brackets ,flush pipes ,grating and union for discharge pipe etc complete all as specified and as directed. |
| 93 | S&F Vitreous China wash down water closet pan (pedestal pattern) (excluding flushing cistern) including Pedestal pan and trap, and connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc.complete and include seat cover etc complete all as specified and directed. |
| 94 | S&F in repair Vitreous china squatting pan \"Orrisa\" patterns of size 580mm x 440mm white, (excluding flushing cisterns and flush pipe),including connection totrap \"P\" or \"S\" pattern with inlet and outlet integral foot rests, complete all as specified and directed. |
| 95 | S&F in repair PVC valveless double syphonic action type flushing cistern low level of 10 Ltr capacity white with inlet ball valve, float, flushing bend & handle including brackets, suitable for both Indian Type Water Closet & Europeon Type Water Closet including brackets & connection to pipe etc complete all asspecifiedand directed. |
| 96 | S&F in repair Health faucet (ABS Body) mild steel CP suitable for 15mm dia pipe with 1.25m long flexible tube and ABS wall hook incl making connection and fixed in position complete all asspecifiedand directed. |
| 97 | S&F in repair Vitreous china WHB 550x400mm size white flat back with brackets incl cutting or pinning ends of brackets (including waste pipe) incl Waste coupling of PTMT (32 mm dia) (half or full threaded) (Minimum weight 32mm 45gms/40mm-60 gmcomplete all as specified and directed. |
| 98 | S&F in repair Brass chromium plated shower rose 125mm size with or without swivel joints of standard size including fixing to 15mm steel pipe or union complete all as specified and as directed. |
| 99 | S&F counter top wash ahnd basin white flat of size 545x545x180mm excluding taps but including 32mm dia chromium plated waste fitting and PVC waste pipe 610 mm long and MS bracket complete all as specified and as directed. |
| 100 | Taking down copper /aluminium point wiring (light, fan, bell,socketor power) complete including fixture and fittings such as switches , ceiling roses , pendent , regulators, sockets, light fitting etc.Removing m,aterials to store for keeping in safe custody or for taking credit ( credit a for above items should be made as per condition seperately ) and making good distrubed surfaces ofwalls, floors etc. complete all as specified and directed. |
| 101 | Taking down old/unserviceable distribution board by disconnection of electric connection carefully SPN DBs/TPN DBs/ Main Switch including old unserviceable MCCBs/ MCBs, Isolators, etc and making good to disturbed surface all as specified and directed at site. |
| 102 | Taking down carefully copper/aluminium Sub main wiring of any size fromsurface/concealed /existing conduit of any height and removing materials at site and making good disturbed surfaces of walls, floors roofs etc complete all as specified and directed. |
| 103 | M&L for point wiring with 1.5 Sq mmsingle corePVC insulated unsheathedcopper FRLSH multi stranded conductor cable in andincludingConcealed PVC conduitof size 20/25mm ISImarked inclusive oftees ,bend ,elbows etc upto and including sunk in Anodized pressed steel box for housing switch socket etc withwhite laminated 3 mm thick sheet cover ISI marked of suitable size complete including PVC insulated multi strandedcopper conductor 1.5Sq mm FRLSH cable as earth wire to common earth dolly for connection to ceiling rose to earth terminalinclcutting, chasses and makinggooddisturbed surface to match with existing finish with plaster forcomplete all as specified and directed. |
| 104 | One light point controlled by one, one way switch 5/6 Amps |
| 105 | One fan point/ exhaust fan point controlled by one, one way switch 5/6 Amps and regulator |
| 106 | One 3 point 5/6 Amps switch socket outlet point controlled by one switch on the same board. |
| 107 | One 3 pin 5/6 Amps switch socket outlet point controlled by one switch on independent boad. |
| 108 | Description all as per item No 103.00 here in before butusing 2.5 sq mm single core copper conductor cable of multistranded FRLSH PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of1.5 sq mm copper conductor FRLSH PVC wire as earth continuity conductor along with wiring and connecting to the common earth dolly. |
| 109 | Supply and fixing switch piano flush button single pole one way 5 amps, AC 240 Volts complete all as specified and directed. |
| 110 | Supply and fixing switch piano flush button single pole one way 15 Amps AC 240 volt complete all as specified and directed. |
| 111 | Supply and fixing socket outlet flush type 5 Amps, 5 pin, AC 240 Volts complete all as specified and directed. |
| 112 | Supply and fixing socket outlet flush type multipurpose 2 in1, 3 pin 5 and 15 Amps, AC 240 volts complete all as specified and directed. |
| 113 | S & F for Ceiling rose, surface Bakelite with 3 terminals, ISImarked for batten fitting complete all as specified |
| 114 | S & F for stepped type electronic fan regulator flush type complete all as specified |
| 115 | Supply and fixing double door TPN DBs 4 wayof powder coated DB\"s suitable for MCB\"s fitted with bus bar,Neutral link,Earth bar and Din ral & DB\"s will be fitted concealed in wall / surface as per site required complete all as specified and directed. |
| 116 | Supply and fixingdouble door SPN DBs 8 wayof powder coated DB\"s suitable for MCB\"s fitted with bus bar,Neutral link,Earth bar and Din ral as per existing finishing complete all as specified and directed. |
| 117 | Supply and fixing MCB TPN 40 to 100 amps 10 KA ,C-seriesincluding connection with suitable size aluminium / copper lugs complete all as specified and directed. |
| 118 | S & F for MCB Single pole and neutral rated capacity 40-63 Amps, 240 Volts breaking capacity 10 KA, \"C\" curve complete all as specified and as directed. |
| 119 | S & Ffor MCB Single pole rated capacity 5 to 32 Amps, 240 Volts breaking capacity 10 KA, \"C\" curve complete all as specified and as directed. |
| 120 | Supply and fixing LED tube light batten box type made of CRCA sheet with decorative end caps suitable with ultra bridght glass LED tube light 1x 18/20 watt T8 type single side connection complete with both end bi-pin holder and all accessories internally prewired and fixed to wall/ceiling incl fittings accessories and connecting up with twin core flexible copper conductor cable suitable size all as specified. |
| 121 | Supply and fixing LED batten tube light fitting 1x 10 watt 230 voltwall/ ceiling mounted luminaire with polycarbonate hoiusing and integrated electronic driver with all accessories internally pre wired and incl connecting up with twin core twisted flexible copper conductor cable suitable size all as specified. |
| 122 | Supply and fixing Wall light fixture lantern made up of metal with chrome finish and white colour diffuser complete with LED 9 watt lamp B-22 base including all necessary accessories and connection complete all as specified and directed. |
| 123 | S & F for Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 for security light fitting luminaire with high power LEDs as light source (100 lm/watt) with LDR sensor for automatic ON/OFF operation and electronic driver of capacity 25 watts with pre wired andnecessary mounting arrangements and provision of 1.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as specified and directed. |
| 124 | Taking down old unserviciable ceiling fan/exhaust fan of any sweep, keeping with safe custody and deposited the same to AGE E/M store complete all as specified and as directed. |
| 125 | S & F for energy efficient exhaust fan of 300 mm sweep made of metal body Ventil Air -DS type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan forconnection and making suitable size ofhole to existing brick wall for fan basecompelte all as specifiedand directed. |
| 126 | Supply and fixing BLDC ceiling fans 1200 mm sweep 230 volts 50 Hz, 5 star BEE rated with brushless direct current motor (BLDC), energy saving, 100 % copper wound motor complete with anti corrosive alluminium blades of minimum thickness 1.10 mm, powder coated finished, double ball bearingmaxmium wattage 26 to 32 watts, Min air delivery 220 (+/- 2%) CFM with service value above 6.50, ISI marked complete all as specified and as directed . |
| 127 | M & L forSub main wiring with approved colour coding as per IS with two single core PVC insulated FRLSH cable with stranded copper conductor of size 4.0 Sq mm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit 20/25mm of white/ ivory colour and its accessaries ISI marked heavy duty of suitable sizeincluding concealed in wall etcone run of PVC insulated with 4.0 Sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire complete all as specified and as directed. Note:- Two runs of 4.0 sqmm cable,one run of 6 sqmm cable and one run of PVC conduit will be measured as one unit. |
| 128 | S&F on load change over switch with enclosures of capacity 63 Amp, 4 pole415 Volt, front handle including necessary provision ofro inserting the change over switch in wall by cuttting the brick/ stome masonary etc and maiing good of disturbed surface to match with existing colour of wall complete all as specified and as directed |
| 129 | Supply, installation andtesting of electric water heater storage vertical type, BEE 5 star rated, 25 ltr capacity 240 volts 50 Hz comprising of high wattage heating element of 2 KW for instant heating, extra Mild steel with Glass lined coated inner tank, rust & shock proof ABS outer body, non-ferrous pressure plate with & including provn of 04 Nos grouting bolts suitably flushed to wall or any other surface including electric connection with 3 core PVC insulated, sheathed, stranded copper conductor cable/ flexible chord and one No 15 amps 3 pin plug top complete all as specified and as directed. |
| 130 | M & L for earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground vertically (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.50 mtr deep below normal ground level, connecting to GI earth wire 4mm dia by means of bolts, nuts, check nuts, and washers of galvanized iron or steel including 15 mm dia. medium grade protection pipe for earth lead complete with charcoal and common salt including watering arrangement with galvanized iron pipe light grade 20 mm dia, PCC Chamber, CI frame and cover, MS funnel with wire mesh all as shown in electrical plate no 3 of SSR part I including excavation and earthwork in any type ofsoil/strata and testing on completion. Note:- GI earth wire 4 mm dia and 15 mm dia protection pipe upto 7.5 mtr from earth plate is deemed to be included in rate quoted. |
| 131 | (Note : The Scope of Work contained in \"Sch of Credit\" amounting to Rs. 1,12,570.50. The Quoted sum shall be arrived at after deducting the amount of “Sch of Credit” from the total amount of the ‘BoQ’ |
