|
| 1 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. |
| 2 | Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 3 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. |
| 4 | Credit for: |
| 5 | Unserviciable Brass Bib/stop cocks/pillar tap |
| 6 | Gun metal gate valve with C.I wheel 20mm dia |
| 7 | Gun metal gate valve with C.I wheel 25 mm dia |
| 8 | Low level PVC flush tanks (10 litres) |
| 9 | Old wooden flush door shutters. |
| 10 | Unserviceable PVC over head water storage tank up to 500Ltr capacity. |
| 11 | PVC pipe,fittings & PTMT fittings etc. |
| 12 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50m outside the periphery of the area cleared. |
| 13 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : |
| 14 | 1:2:4 (1 cement : 2 coarse sand(zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 15 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: |
| 16 | Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 17 | Deduct for not providing hinges in doors, windows or clerestory window shutters with : |
| 18 | ISI marked Stainless steel butt hinges with stainless steel screws : |
| 19 | For 2nd class teak wood and other class of wood shutters |
| 20 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: |
| 21 | 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 22 | 25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. piano hinges with necessary screws |
| 23 | Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws : |
| 24 | 35 mm thick shutters. |
| 25 | With ISI marked stainless steel butt hinges of required size - Kiln seasoned selected class of sheesham wood |
| 26 | Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets : |
| 27 | 20 mm dia (heavy type) |
| 28 | Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete (Copper oxidised as per IS 1378) |
| 29 | 250x16 mm |
| 30 | Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete (Copper oxidised as per IS 1378) |
| 31 | 150x10 mm |
| 32 | Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete (Copper oxidised as per IS 1378) |
| 33 | 100 mm |
| 34 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 35 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. |
| 36 | (i)Single socketed pipes. |
| 37 | 75 mm diameter |
| 38 | 110 mm diameter |
| 39 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. |
| 40 | Bend 87.5° |
| 41 | 75 mm bend |
| 42 | 110 mm bend |
| 43 | 12 mm cement plaster of mix : |
| 44 | 1:4 (1 cement: 4 coarse sand) |
| 45 | Finishing walls with water proofing cement paint of required shade : |
| 46 | New work (Two or more coats applied @ 3.84 kg/10 sqm). |
| 47 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade |
| 48 | New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) |
| 49 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: |
| 50 | Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. |
| 51 | Washed stone grit plaster on exterior walls of height upto 10 metre above ground level, in two layers, under layer 12mm cement plaster 1:4 (1cement: 4 coarse sand), furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 2 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand :2 stone chipping 10mm nominal size), in panels with groove all around as per approved pattern, including scrubbing and washing the top layer with brushes and water to expose the stone chippings, complete as per specification and direction of Engineer-in- charge (Payment for providing grooves shall be made separately). |
| 52 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC (Volatile Organic Compound ) content less than 50 gram/ litre, of approved brand and of required shade and colour complete to give and even shade. |
| 53 | Old work (one or more coats) |
| 54 | White washing with lime to give an even shade : |
| 55 | Old work (one or more coats) . |
| 56 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : |
| 57 | One or more coats on old work. |
| 58 | Polishing on wood work with ready made wax polish of approved brand and manufacture : |
| 59 | Old work . |
| 60 | Finishing walls with water proofing cement paint of required shade : |
| 61 | Old work (one or more coats @ 2.20 kg/10 sqm) complete. |
| 62 | Finishing walls with Acrylic Smooth exterior paint of required shade : |
| 63 | Old work (One or more coat applied @ 0.90 ltr/10 sqm). |
| 64 | Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: |
| 65 | Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm). |
| 66 | Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspectionof work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineer-in-charge. The elevational area of the scaffolding shall be measured for payment purpose. The payment shall be made once |
| 67 | irrespective of duration of scaffolding.Note: - This item to be used for maintenance work judicially, necessary deduction for scaffolding in the existing item to be done. |
| 68 | Cleaning of terrace/loft water storage tank (inside surface area) upto 2000 litre capacity at all heights with coconut brushes, duster etc., removal of silt, rubbish from the tank and cleaning the tank with fresh water disinfecting with bleaching powder @ 0.5gm per litre capacity of tank, including marking the date of cleaning on the side of tank body with the help of stencil and paint and disposing of malba, all complete as per direction of Engineer-in-Charge. (The old date already written on tank should be removed with paint remover or black paint and if date is not written with the stencil or old date is not removed deduction will be made @ Rs. 0.10 per litre if during cleaning any GI fittings or ball cock is damaged that is to be repaired by contractor at his own cost and nothing extra will be paid on this account) |
| 69 | Cleaning and de-silting of gully trap chamber, including removal of rubbish mixed with earth etc. and disposal of same, all as per the direction of Engineer-in-charge. |
| 70 | Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in- Charge. |
| 71 | Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge. |
| 72 | Cleaning of drainage manholes and sewer lines by removing the deposited and other rubbish from the manholes and cleaning the sewer lines by rodding and flushing with water as directed by the Engineer -in- charge. (Rate per One manhole and sewer line to next manhole) |
| 73 | Mechanical cleaning of Septic Tank by using mechanical cleaning mechine by suction, pumping, vaccum cleaning and removing all the waste liquid and sludge from the septic tank and disposaing the waste at Municipal dumping ground. The rate includes all mechinery and workmen required and all incidental charges during pumping, filling, transporting etc complete as directed by the Engineer-in-charge. |
| 74 | Cleaning of chocked water supply GI pipe line by pressure machine for proper supply of water i/c opening and refixing of bends, socket etc whichever necessary all complete as per direction of Engineer-in-Charge. |
| 75 | Checking and making good all leakages etc. in GI,C.I,SCI,CI pipes etc.complete as per the direction of the Engineer-in-charge. (Major fittings etc.to be paid separately). |
| 76 | Repair of low level PVC cistern by p/f internal fittings whichever is required including testing and checking for proper working etc. all complete as per direction of Engineer-in-Charge. |
| 77 | Uprooting of undesired grown-up plants over walls at any floor level and filling the hole after uprooting of plants root with cement mortar 1 : 2(1 cement:2 fine sand) including making arragement for jhula, ladders, rops etc. complete asper direction of Engineer-in- charge. |
| 78 | Providing and fixing C.P. brass pillar tap 15mm nominal bore for wash basins as directed. |
| 79 | Providing and fixing white vitreous china water closet squatting pan (Indian type) : |
| 80 | Orissa pattern W.C. pan of size 580x440 mm |
| 81 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. |
| 82 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. |
| 83 | 10 litre capacity - White |
| 84 | Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete : |
| 85 | White solid plastic seat with lid |
| 86 | Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings : |
| 87 | Flat back wash basin of size 550x400 mm. |
| 88 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. |
| 89 | Flexible pipe |
| 90 | 32 mm dia |
| 91 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : |
| 92 | Rectangular shape 453x357 mm |
| 93 | Providing and fixing M.S pipe clip for SCI & CI Pipes complete with 75 mm gulmake etc complete as per direction of Engineer-in-Charge. (a) 100 mm diametre pipe. |
| 94 | Providing and fixing PVC tank lid to the overhead tank with necessary screws, nails, bolts & nuts complete etc.,as per the directions of Engineer-in-charge. |
| 95 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : Internal work - Exposed on wall |
| 96 | 15 mm nominal outer dia. Pipes. |
| 97 | 20 mm nominal outer dia. Pipes. |
| 98 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : |
| 99 | 25 mm nominal bore |
| 100 | 20 mm nominal bore |
| 101 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : |
| 102 | 100 mm diameter |
| 103 | Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws including excavation, refilling the earth or cutting of wall and making good the same complete wherever required : |
| 104 | 15 mm nominal bore. |
| 105 | 20 mm nominal bore. |
| 106 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 107 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931: |
| 108 | 15 mm nominal bore. |
| 109 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 : |
| 110 | 15mm nominal bore |
| 111 | Providing and fixing PTMT bib cock of approved quality and colour. |
| 112 | 15mm nominal bore, 86 mm long. Weighing not less than 88 gms. |
| 113 | Providing and fixing PTMT pillar cock of approved quality and colour . |
| 114 | 15mm nominal bore, 107 mm long. Weighing not less than 110 gms. |
| 115 | Providing and fixing Stainless Steel grating 0.60mm thick grating for floor traps complete as directed. |
| 116 | 100mm dia Circular |
| 117 | Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball. |
| 118 | 15 mm nominal bore, 105 mm long. Weighing not less than 138 gms. |
| 119 | Providing and fixing PTMT angle stop cock 15 mm nominal bore. Weighing not less than 85 gms. |
| 120 | Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. |
| 121 | 15 mm nominal bore with 30 cm length. |
| 122 | Repairs to steel windows by welding necessary hinges including arranging welding machine at site and applying grease etc as directed. |
| 123 | Cleaning of under ground water storage tank including dewatering of tank by section machine/manually, cleaning of accumulated waste/silt/algee using coper sulphate (algicide) disinfecting of walls with bleaching powder @ 150gm of bleaching powder for 1000 ltr water, keeping it in the tank at least for three hours before flushing, finally cleaning the same with fresh water and putting the date of cleaning on the tank with synthetic enamel paint, disposal of all waste up to approved dumping site, out side the premises of compound etc all complete in such a way to restore water supply with out unwanted interruption in the compound as per direction of Engineer-in-Charge. |
| 124 | Renewing fly proof galvanised M.S. wire gauge of existing wooden/steel door/windows using M.S.wire gauge with average width of aperture including wooden/MS flates, nails, screws or nuts and bolts including dismentling of existing wire mesh and shutter if required including credit of old unserviciable wire mesh etc. complete as per direction of Engineer-in-charge. |
| 125 | Cleaning of open surface drain including complete, removal of earth, silt, slush, brick bats, garbages and other refuses, disposing off the same to dumping site in township complete asper the direction of the Engineer-in-Charge. |
| 126 | Cleaning of vertical drainage pipe, SCI vent, soil pipes, rain water pipe by rodding and water etc complete as per direction of Engineer-in-Charge. |
| 127 | Hiring Electric Welding Machine at the site of work including placing at all floors of the building: (a)For the period of 4 hours. |
| 128 | Repairing of damaged chhajas edges with cement concrete 1: 1.5 :3 (1 cement : 1.5coarse sand : 3 graded stone aggregate 12.5mm nominal size) including finishing with cement plater 1:3 (1 cement: 3 fine sand), including cutting and removal of existing damaged concrete, providing and fixing murga net jali wherever required and applying a coat of cement slurry 0.67 kg/Sqm mixed with water proofing material as recommended by the manufa- cturer after scraping exposed rusted reinforcement and applying a coat of Anti - rusted chemical (Rust - ohm or equivalent) on old reinforcement etc. complete as per direction of Engineer- in-charge up to floor V level including cost of double folding scaffolding. |
| 129 | Supply labour for cleaning terraces, Cleaning of floors, doors-window and aluminium partition & shutters etc wherever required complete as per satisfacation and direction of the Engineer-in-charge. (All the T & P shall be arranged by the Contractor.) |
| 130 | Cleaning of sewer line and disposal of sludge out of compound and as per direction of Engineer-in-charge. |
| 131 | Providing and fixing MS Sheeted tank lid to the overhead tank with necessary screws, nails, bolts & nuts complete etc.,as per the directions of Engineer-in-charge. |
