|
| 1 | Earth work in excavation by mechanical means (Hydraulic Excavator )/ manua| means in foundation trenches or drains (not exceeding 1,5 m in width or 10 sqm on plan) including dressing of sides and ramming of bat- toms, lift upto 1.S m, including getting out the excavated soil and disposaI of surplus excavated soil aS directed, within a lead of 50 m. All kinds of soil. |
| 2 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50m and lift upto 1.5m |
| 3 | Supplying and filling in plinth with sandy soil under floors including, watering, ramming consolidating and dress.ng complete. |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering- -All work upto plinth level: 1 :4:8 (1 Cement: 4 coarse sand: 8 graded stone aggregate 40 mm nominal size) |
| 5 | Providing and laying in position ready mixed or site bathched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/ Ordinary Portland/ Portland slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting, of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of concrete. All works upto Plinth level, concrete of M-25 grade with minimum cement content of 330 kg/cum |
| 6 | Providing and laying in position ready mixed or site batched desfgn mix cement concrete for reinforced cement concrete work; using coarse aggregate and fina aggregate derived from naNral sources, Portland Pozzolana / Ordinary Portland /PortIand Slag cement, admlxtures in recommended proportions as per IS: 9103 to accelerate /retard setting , of concrete, to improve durability and workability without impalring strength; including pumping of concrete to site of laying, curing, carriage for all leads; but exduding the cost of cantering, shuttering, finishing and reinforcement as per dlrectlon of the engineer-in-charge; for the following trades of concrete. All works above Plinth level upto floor V level. Concrete of M-25 grade with minimum cement content of 330 kg/cum. |
| 7 | Reinforced cement concrete work in beams,suspended floors, roofs having slope upto z5’ landings, balconies, shelves, chajJas, lintels, bands, plaln window silIs,stalrcases and spiral stair cases above pllnth level upto floor flve Iwel, excluding the cost of centering, shutterlng, finishing and reinforcement with 1 :1.5:3 (1 cement: 1.5 coarse sand: 3 graded stone aggregate 20 mm nominal site) |
| 8 | Providing and iaylng damp-proof course S0 mm thick whh cement concrete 1 :2:4 (1cement : 2 coarsa sand : 4 graded stone aggregate 20mm nominal site) . |
| 9 | Applying a coat of residual petroleum bitumen of grade vG-10 of proved quality using 1.7kg per squara metre on damp proof course after cleaning the surface with brushes and finally with a pie¢e of cloth lightly soaked in kerosene |
| 10 | Reinforcement for R.C.C. work including straightening, cutting, bending,placing in position and binding all complete up to Plinth level. 5.20.2 Thermo-Mechanically Treated bars. |
| 11 | Reinforcement for R.C.C. work including straightening, cutting, bending,placing in position and binding all complete. Above Plinth level. 5.50 A.2 Thermo-Mechanically Treated bars. |
| 12 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering- -All work upto plinth level: 1 :4:8 (1 Cement: 4 coarse sand :8 graded stone aggregate 40 mm nominal size) |
| 13 | Half brick masonry with 1st class common burnt clay F.P.S. (non modular) bricks in superstructure above plinth level upto floor V level in Cement mortar 1 : 4 (lcement: 4 coarse sand) |
| 14 | Centering and shattering including struting, propping etc and removal of form for; Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick. |
| 15 | Centering and shuttering including strutting, propping etc. and removal of form for: Columns, Millars, Piers. Abutmcnts. Posts and Struts. |
| 16 | 52mm thick cement concrete flooring with concrete hardener topping under layer 40mm thick cement concrete 1:2:4 ( 1cement: 2coarse sand: 4graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1cement hardener mix: 2 graded stone aggregate 6mm nominnal size) by volume hardening compound is mixed @ 2 litre per 50kg of cement or as per manufacturers specifications This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete |
| 17 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fastener of required dia and length (hold fast lugs or dash fastener shall be paid for separately : Local best quality Tolhao wood. |
| 18 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked MS pressed butt hinges bright finished of required size with necessary screws. Local best quality Tolhao wood 30mm thick |
| 19 | Providing and fixing aluminium sliding door bolts ISI marked anodised ( anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with nurs and screws etc. complete : 300 x 16mm |
| 20 | Providing and fixing aluminium tower bolts, JS marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete: 250x10 mm |
| 21 | Provldlng and fixing chromium plated brass handlas wlth necessary screuts etc. complata125 mm |
| 22 | Providing 40x5 mm flat Iron hold fact 40 cmk›ng Indudlng fixing to fzame wlth l0mtn diameter bolts, nuO and wooden plugs and embedding in sement concrete block 3010 x 15cm 1.3:6 mlx (1 cement : 3 coarse sand : 6 graded stona aggregate 20mm nominal size) |
| 23 | steel workin built up tubular tround, square orrectangular tubes etc.) trusses etc. Including cutting, hoisting fixing in position and applying a priming coat of approved steel primer, including welding and bolted including special shaped washers etc, complete. Hot finished welded type tubes |
| 24 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240mpa steel grade, 5-7 microns epoxxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied 1 in single length upto 12 metre or as desired by Engineer-in charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5 x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vettical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with precoated galvanised iron profile sheets 0.35 mm thick |
| 25 | Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120gsm as per IS: 277 in 240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/self tapping screws or with polymer coated J or L hooks, bolts and nut and or G.I seam bolts and nuts, G.I plain and bitumen washers complete: Ridges plain ( 500-600mm). Precoated galvanised iron profile sheets 0.35 mm thick |
| 26 | Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120gsm as per IS: 277 in 240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/self tapping screws or with polymer coated J or L hooks, bolts and nut and or G.I seam bolts and nuts, G.I plain and bitumen washers complete: Ridges plain ( 500-600mm). Gutter (600mm over all girth) Precoated galvanised iron profile sheets 0.35mm thick |
| 27 | Providing and fixing an wall face Unplasticised Rigid PVC rain water pipes conforming to IS 13592 type - A including jointing with seal ring conforming to IS:5382 leaving 10 mm gap for thermal expansion, (i) Single socketed pipes 75 mm diameter |
| 28 | Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar bent to shape with hooked ends in R.C C slabs, beams during laying including painting the exposed portion of loop, all as per standard design complete |
| 29 | Internal Water Supply and Sanitary Installation |
| 30 | Provlding and fixing water closet squatting pan (lndian type W.C. pan) with 100 mm sand cast Iron P or Strap, 10 litre low level white I P V,C. flushlng cistern, including flush pİpe, With manually controlled device (handle lever) conforming to IS: 7231, wlth all fittings and fixtures complete, including cutting and making ,good the walls and floors wherever required white vitreous china Orissa pattern W.C. pan of slze 580 x 440 mm with integral type foot rests |
| 31 | Providing and fixing stainless steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I brackets and stainless steel plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink without drain board 610 x 460 mm bowl depth 200mm |
| 32 | Providing and fixing wash basin with C.I brackets, 15mm CP brass pillars taps, 32mm CP brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the wall wherever required : White Vitreous China Flat back wash basin size 450 x 300mm with single 15mm C.P brass pillar tap |
| 33 | Providing and flxlng PTMT Waste Coupling for wash basin and sink, of approved quality and colour. Waste coupling 38 mm dia of 83 mm length and 77mm breadth,weighing not less than 60 gms |
| 34 | Providing and fixing PVC waste pipe for sink or wash basin including PVC waste fittings complete. Flexible pipe 40mm dia |
| 35 | Providing and fixing 600 x 450 mm beveled edge mirror of superior glass ( of approved quality) complete with 6mm thick hard board ground fixed to wooden cleaats with C.P brass screws and washers complete. |
| 36 | Providing and fIxfng PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape wìth bracket of , the same materlals wlth snap fittings of approved quality and colour, weighing not less than 105 gms. |
| 37 | Providing and fixing Chlorinated PoIyvinyl Chloride (CPVC) pipes. thermal Stability for hot & cold water supply. including all CPVC plain & brass threaded fittings, i/c fixing the pipe with Clamps at L.00 m I spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost ol cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. 25 mm nominal outer dia Pipes |
| 38 | Providing and placing on terrace (at all floor levels) polyethylene water Storage tank, IS 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base Support far tank. |
| 39 | Providing and faxing PTMT extension nipple for water tank pipe, fittings of approved quality and colour. 25mm nominal bore, weighing not lessthan 62 gms |
| 40 | Structural steel work ¡n single section fixed with or without connecting plate including cutting, hoisting, fixing in position and applying coat of 1 approved steel primer all complete. (a) Vertical [ISMC 49.5x 49.5x4.5]:[[email protected]/m], (b) Horizontal [ISMC 38x38x4.0]: [14x1.52=21.28m @3.95 kg/m] |
| 41 | Ready made Septic tank |
| 42 | IEI |
| 43 | Wiring for light point / fan point / exhaust fan point / call bell point with 1.5mm2 FR PVC insulatedcopperconductorsinglecorecableinPVCcasing&cappingwithmodulartype switch,modularplate, suitablesizeG.I.boxandearthingthepointwith1.5mm2FRPVCinsulated copper conductor single core cable etc. as reqd. |
| 44 | Group A - 297 nos. |
| 45 | Group B - 264 nos |
| 46 | Group C-198 nos |
| 47 | Total |
| 48 | Wiring for light point / power plug with 2x4mm2 FR PVC insulated copper conductor single corecableinPVCcasing&cappingalongwith1no.4mm2FRPVCinsualtedcopper conductor single core cable for loop earthing etc. as reqd. |
| 49 | a) Lightplugpoint. - 198 Nos |
| 50 | a) Lightplugpoint. - 198 Nos |
| 51 | Total |
| 52 | S/F suitable size GI box with modular plate and cover in front on surface /recess i/c P/F 3 pin 5/6 amp socket outlet and 5/6 amp modular switch, connection painting etc. as reqd. (for light plugs to use in non-residential building). |
| 53 | S/F suitable size GI box with modular plate andcover in front on surface /recess i/c P/F 6 pin 15/16 and 5/6 amp modular socket outlet15/16 amp modular switch, connection painting etc.as reqd. |
| 54 | Wiringforcircuit/sub-mainwiringalongwithearth wirewith (thefollowing sizesof)FRPVC insulated copper conductor single core cable in PVC casing & cappingetc. as reqd. |
| 55 | a. 2x1.5mm2 +1x1.5mm2 earth wire. |
| 56 | b. 2x2.5mm2 +1x2.5mm2 earth wire. |
| 57 | c. 2x6mm2 +1x6mm2 earth wire |
| 58 | Fitting Accessories |
| 59 | S/F 15W Surface mounting LED down light with white powder coated aluminum housing with integrated electronic driver i/c connection as reqd.(HAVELLS) |
| 60 | S/F 18 W LED 6500 K Decorative ultra slim square profile LED lighting fixture with extruded polycarbonate,environmentalfriendly,energy efficientready tousepack.i/cconnectionas reqd. |
| 61 | S/F LED ADORE 15W,B22,6500K,Lumen Output 1425lm.CDL 3 STAR BALL LAMP,HAVELLS. |
| 62 | S/F brass batten / angle holder i/c connection etc. as reqd. |
| 63 | S/F 48\"\" sweep (1200mm) A.C. ceiling fan complete with down rod, cannopy, 3(three) blades but without regulator etc. as reqd. (Make Bajaj/Usha or Similar). |
| 64 | S/F stepped type electronic fan regulator on the existing modular plate switch box i/c connection but excluding modular plate etc. as reqd. |
| 65 | S/F 305mm sweep exhaust fan complete with all accessories i/c connection eic. as reqd. |
| 66 | Switch Gear: |
| 67 | P/F 200 amp TP & N dis-connector fuse switch unit inside the existing cubicle panel board with ISI marks HRC fuses i/c drilling holes in the cubicle panel board, making connection etc.as reqd. |
| 68 | S/F 8 way,(2+8way) single door, single and neutral, prewired, sheet steel, MCB distribution board,240volts,onsurface/recess,completewithloosewirebox,terminalblocks,tinned copperbusbar,neutrallink,earthbar,dinbar,detachableglandplate,interconnection, includingpowder coat painting, earthng etc. as required. (but without MCB/RCCB/Isolator). |
| 69 | S/F 6 way, (2+6way) single door, single pole and neutral, prewired, sheet steel, MCB distributon board, 240 V on surface/recessd complete with loose wire box, terminal blocks, tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnection,including powder coat painting, earthing etc. as reqd. (but without MCB/RCCB/Isolator). |
| 70 | S/F63amp,doublepole,240volts,isolatorintheexistingMCBDBcompletewith connections, testing and commissiong etc. as reqd. |
| 71 | S/F 5 amp. To 32 amp. Rating 230V \"B\" series MCB for lighting and other load of single pole in the existing MCB DB complete with connection testing and commissioning etc. as reqd. |
| 72 | Earthing Items: |
| 73 | P/F 8SWG dia copper wire on surface or in recessed for loop earthing along with existing surface/ recessedconduit /sub-main wiring /cable as reqd. |
