|
| 1 | JOB No. 3BRD/SR(B&R)/03/2025-26 |
| 2 | Demolition of lime concrete / lean concrete /Brick bats etc. from sunken slab portion exc. 15 cm thick but above ground floors, complete all as specified and directed by Engr-in-Charge including removal of demolished material from MD land debries away from site to a disignated point by local administration or a distance up to 1.5 km from site complete all as specified and directed by Engr-in-Charge. |
| 3 | M&L for 25 mm thick cement concrete (1:2:4) type B-0 using 12.5 mm graded crushed stone aggregates as in flooring laid in slope complete all as specified and directed by Engr-in-Charge. |
| 4 | M&L lean concrete type E-2 (1:5:10) using 40mm bricks bats aggregate as in sunken portioncomplete all as specified and directed by Engr-in-Charge. |
| 5 | M&L for 40mm GI mediun grade Spout pipe for sunken work complete. |
| 6 | M&L for providing water proofing tratment of sunken portion of WCs, bathroom etc. by applying cement slurry mixed with Acrylic based polymer modified cementitious composite compound coating of make asapproval in Technical Instruction 5/2003 by adding :(a) 15mm thick plaster (1:4) cement sand mortar with integral water proofing compound 2% by weight of cement on floor and wall / beam , finishing the surface even and smooth without using extra cement. The surface shall then be cured and allwedto dry. (Note : Water proofing compound shall be measured and paid separately).(b) First layer of slurry of cement @ 0.5 kg/sqm mixed with Acrylic based polymer modified cementitious composite compound @ 0.25 kg/sqm. This layer will be allowed to air cure for 4 hrs.(c) Second layer of slurryof cement @0.25 kg/sqm mixed with Acrylic based polymer modified cementitious composite compound @ 0.15 kg/sqm. This layer will be allowed to air cure for 4 hrs followed with water curing for 48 hrs complete all as specified and directed by Engr-in-Charge.NOTE : Floor area of the sunken slab shall be measured only.Make of Acrylic based polymer modified cementitious compound -Fosroc ( Brushbond) /Sika (Sikatop-100)/ Pidilite |
| 7 | Supply only water proofing compound ISI marked complete all as specified and directed by Engr-in-Charge. |
| 8 | S&F in repair 100 mm cast iron soil waste and vent pipe in any length with or without ears jointed with cement mortar (1:3) fixed to wall, laid in trenches or in floors, complete all as specified and directed by Engr-in-Charge. |
| 9 | All as per Srl item No. 8.00 here-in-before but 75 mm dia. |
| 10 | S&F 100 mm cast iron bends complete all as specified. |
| 11 | All as per Srl item No. 10.00 here-in-before but 75 mm dia. |
| 12 | S&F Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallelbranches 100 mm dia complete all as specified and directed by Engr-in-Charge. |
| 13 | S&F Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches 75 mm dia complete all as specified and directed by Engr-in-Charge. |
| 14 | S&F in repairs 75 mm dia cast iron Floor Trap/Nahani Trap, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified |
| 15 | S&F in repairs 100 mm dia cast iron Floor Trap/Nahani Trap, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified |
| 16 | M&L for Cutting holes into or through brick walls built in cement mortar or cement lime mortar having superficial area exceed 150 Sqcm n.exc 400 Sqcm each making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 complete all as specified and directed by Engr-in-Charge. |
| 17 | S&F in repair PVC (SWR) pipes 110mm dia Single socketed, in any length with rubber ring joints fixed to walls, laid in trenches, floors etc complete all as specified and directed by Engr-in-Charge. |
| 18 | S&F of 50mm bore PVC (SWR) high density polyethylene (HDPE) pipes of pressure rating 6 kgf/sq. cm pipes single socketed, in any lenth with rubber ring joints laid in trenches or in floors. |
| 19 | S&F 110mm PVC (SWR) bends any radius complete all as specified and directed by Engr-in-Charge. |
| 20 | Taking up or down GI steel/ Kitek tubing 15 mm with connections or fittings from wall, ceiling, floor etc |
| 21 | Taking up or down GI steel/ Kitek tubing 20 mm with connections or fittings from wall, ceiling, floor etc |
| 22 | S&F GI water tubes, 15 mm bore medium grade, galvanized with all fittings and fixed complete to walls, ceiling or laid in floors complete all as specified and directed by Engr-in-Charge. |
| 23 | S&F GI water tubes, 20 mm bore medium grade, galvanized with all fittings and fixed complete to walls, ceiling or laid in floors complete all as specified and directed by Engr-in-Charge. |
| 24 | Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding n exc 150 sqm girth. |
| 25 | Taking down cement plaster of any description on brick or stone walls, ceiling etc, including raking out joints, hacking for key scrubbing down with water, etc,complete all as specified and directed by Engr-in-Charge. |
| 26 | M&L Rendering 15mm thick on brick surfaces of wallin cement mortar (1:6), finished even and smooth without using extra cement, cement plaster and racking out joints, hacking for key scrubbing down with water etc, complete all as specified and directed by Engr-in-Charge. |
| 27 | M&L for Rendering 10 mm thick in cement mortar (1:4) on ceiling, parapet, chajjas, facias of building and finished the surface even and smooth without using extra cement, complete all as specified and directed by Engr-in-Charge. |
| 28 | M&L for preparation of new plastered/concretesurfaces of walls and applying two coats of oil bound distemper over one coat of primer, over 2mm thickwhite putty white or tinted upto 12 Metre height including necessary scaffolding etc complete all as specified and directed.Note :- Application of distemper shall be with the help of a roller only. |
| 29 | M&L for preparation of new plastered /concrete surfaces of ceiling and applying two coat of oil bound distemper, white or tinted with 2 mm thickwhite putty) upto 12 Metre height including necessary scaffolding etc complete all as specified and directed.Note :- Application of distemper shall be with the help of a roller only. |
| 30 | M&Lfor 15mm thick rendering in cement mortar 1:4 on walls of surfaces finished fair and even without using extra cement upto 12 Metre height complete all as specified anddirected.Note :- WPC shall be measured and paid separately. |
| 31 | M&L for preparation of new plastered/concrete surface of wall/chajjas/facia and applying two coats of exterior emulsion paint over one coat of primer upto 12 Metre height including necessary scaffolding etc complete all as specified and directed. |
| 32 | S&F forcontinuos piano hinges, mild steel bright finishwidth of flap 40mm,fixed complete all as specified and as directed. |
| 33 | M & L for non - skid Ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 15 mm thick screed bed in cement mortar 1:6 and dismantling of existing tiles andrubbish off the premises debrish away from site to a disignated point by local administration or a distance up to 1.5 km from site complete all as specified and directed by Engr-in-Charge. |
| 34 | S&F in repair of Vitreous china one piece EWC standard size white / ivory colour, wall hanging / floor mountedwith dual flushing cistern white including \"P\" or \"S\" trap, fixed as complete all as specified and directed. Make : Jaquar/ Cera/ Parryware. |
| 35 | M&L for Glazed ceramic tiles in vertical surface 350 x 250 x 7 mm /450 x 350 x7mm thickas in skirting, dados, risers to steps, etc set and jointed in neat cement slurry and pointed in coloured cement to match tiles,over and including 10 mm thick for wall finished in CM 1:4, including dismantaling floor hearth or wall tiling incl cement mortar bedding (but not backing) removal of rubbish off the premises debrish away from site to a disignated point by local administration or a distance up to 1.5 km from sitecompletecomplete all as specified and directed by Engr-in-Charge. |
| 36 | M&L for Non-skid Ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 15 mm thick screed bed in CM 1:6 and dismantling of existing tiles andrubbish off the premises debrish away from site to a disignated point by local administration or a distance up to 1.5 km from sitecomplete all as specified and directed by Engr-in-Charge. |
| 37 | S&F in repairs for Chromium plated brass angle valve for 15mm bore pipe, fixed complete all as specified and directed. Make : Cera (Cat No. : F8040204), Parryware (Cat No : WPT9926A1), Hindware (Cart part : F570043CP) |
| 38 | S&F 15 mmBib taps long body cast copper alloy chromium plated with capstan head, screwed down, screwed for iron pipe or for brass ferrule 15mm bore fixed in repair. |
| 39 | S&F in repairs 15 mm brass chromium plated wall mixer for mixing Hot and Cold water screwed down for iron pipes for complete all as specified and directed. |
| 40 | S&F in repairs for Vitreous China under counter basin wash basin, white or ivory colour flat back, size 470mmx350mm excluding taps, waste chain and plug and porcelain stopper but including brackets any size, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe etc fixed complete all as specified and directed. |
| 41 | S&F PVC Bath Room cabinet mirror size - 600x450mm incl necessary arrangement complete all as specified and directed by Engr-in-Charge. |
| 42 | S&F for CP Toilet paper holder including all fitting and fixturecomplete. Make : Jaquar/ Parryware/ Hindware. |
| 43 | S&F for Rotational moulded polyethylene white water storage tanks 1000 litres capacity three layered white in colour (clylindrical vertical with threadedclosed top) hoisted and fixed in position all as specified in SSR Part I including dismantling of existing water tank. Make : Sintax, Poly plast, Supreme etc. |
| 44 | S&F in repairs for Tubular towel rail of brass chromium plated, 20mm dia, D type, 60 cm long between flanges, fixed complete all as specified and directed by Engr-in-Charge. |
| 45 | M&L Granite18 to 20 mm thick work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms, vertical surface of wallalso and like in 12mm thick Screed bed or bedding layer cement mortar (1:3) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of graniteetc complete all as specified and directed. |
| 46 | M&L for edge moulding to 18-20mm thick stone of counters vanitiesetc. including machine polishing to edge to give high gloss finish etc complete. |
| 47 | Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles and removing the debris outside the defence land all as specified and directed. |
| 48 | M&L for Brick work with sub class \"B\" bricks, straight or curved on plan exc. 6m mean radius built in cement mortar 1:6 complete all as specified and directed. |
| 49 | S&F Prelaminated particle board 18/19mm thick, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber framework. |
| 50 | M&L for Reinforced cement concrete Type B1 1:2:4 (20 mm graded crushed stone aggregate) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like bases. complete all as specified & directed. |
| 51 | S&F for mild steel TMT bars of 10mm dia and over, cut to length, bent to shape required including cranking, bending spirrally for hooping for columns hooking ends and binding with a incluidng mild steel wire (annealled) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-in-Charge. |
| 52 | M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings self and similar work; not exceeding 200mm thick (Horizontal or sloping), work in rough finished flat surfaces of concrete complete all as specified and as directed. |
| 53 | S&F in repairs 15 mm brass chromium plated centre hole WHB mixer with connection pipe for mixing Hot and Cold water screwed down for iron pipes. |
| 54 | S&F 5.50mm thick 800 x 600mm mirror of selected quality glass with eadge moulding, mounted on wall fixed with SS stud fixed complete all as specified and directed. |
| 55 | S&F for sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60 cm long, complete all as specified and directed. |
| 56 | S&F PVC connection 15 mm size with PTMT nuts of lengh 450 mm long. |
| 57 | S&F health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 58 | S&F in repairs Chromium plated shower roses swivel shower brass chromium platedwith arm 100 mm size for fixing with 15 mm pipes with swivel joints, any size including fixing to steel pipes or union. |
| 59 | S&F PVC waste pipe 32mm dia, complete with 600mm long flexible for WHB fixed in repairscomplete all as specified and directed by Engr-in-Charge. |
| 60 | All as per Srl Item No. 59.00 here-in-before but 40mm dia for sink complete all as specified and directed by Engr-in-Charge. |
| 61 | M&L 12mm thick glass reinforced gypsum (GRG) ceiling (sizeoftiles 595 x 595mm) of approved design fixed with powder coated (powder coating on web bottom only) GI grid consistingof main Tee with grooves section of size (15mm x 30mm), cross Tee with grooves section of size (15mm x 23mm)and powder coated GI wall angle of size (20mm x 20mm) suitable for mounting tiles of 595 x 595mm with 4mm dia GI wire suspender including fabrication complete as per manufacturers instructions fixed with steel rawl plug with nut and bolts arrangement with grid size 60x120cm complete all as specified and directed. Make : Diamond Brand TM/ Armstrong/ Everest/ Dexune. |
| 62 | Taking down chowkhat or frame n .exc. 1.5 sqmeach without taking off shutter from the frame complete all as specified and directed. |
| 63 | Taking down chowkhat or frame exc. 1.5 sqm but n.exc 4 sqm each without taking off shutter from the frame complete all as specified and directed. |
| 64 | S&FFactory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 x 75 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engr-in-Charge. |
| 65 | S&F Factory made Solid PVC moulded Door Shutter30mm thick (stiles), with 2, 4 or 6 raised panel design with 2mm thick Moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face with particle board core, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed. |
| 66 | Supply and Fix, Aluminium anodised, barrel tower bolts 150 mm long, powder coated, of extruded section and fixed, complete all as specified and directed. |
| 67 | Supply and fix, butt hinges, 100mm long, extruded aluminium alloy with galvanised stain less steel hinge pin, complete all as specified and directed. |
| 68 | S&F Aluminium handles, cast type, anodised 100mm in size fixed with screws complete all as specified and directed. |
| 69 | S&F forPowder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions frames (Fixed portions) with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws.all complete as per architectural drawings and the directions of Engr-in-Charge. |
| 70 | S&F forPowder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows(two or three track sliding/openable) & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene asket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, auminium snap beading for glazing/ paneling, C.P. brass/ tainless steel screws all complete as per architectural drawings and the directions of Engr-in-Charge. |
| 71 | S&F for Powder Coated aluminium grill of approved pattern cut to required size/shape and fixed with position with aluminium bedding & frame with & including U sections, fixed to aluminium door/windows/ventilators complete all as specified and directed. |
| 72 | M&L for aluminium composite panel sheet of 4mm thick which consists of 3mm thick thermoplastic core of anti-toxic LDPE sandwiched between 2 skins of 0.5mm thick aluminium foils with outer surfaces finished with 30 u PVDF and inner surface finished with a thin coat of polyester paint, fixed in panel to aluminium frame including all necessary frame work or powder coated snap beading and rubber basket complete all as specified and directed.Make :- Alstone/ Alex panel/ Armstrong/ Euroboard. |
| 73 | Supply and fix 5mm thick float glass, tinted/smoked shape fixed to frame /shutter for Aluminium door/window/partition etc including aluminium powder coated snap beading and rubber gasket, complete all as specified and directed. |
| 74 | Supply and fixing Aluminium (die cast) Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed, complete all as specified and directed. |
| 75 | Supply and fixing brass mortice lock vertical type 100mm size, 6 lever fixed in aluminium shutter, complete all as specified and directed. |
| 76 | Supply and fix 180mm size powder coated (any tint) aluminium \"American Handle\" fixed to aluminium door with suitable screws, complete all as specified and directed. |
| 77 | Supply and Fix, Aluminium anodised, barrel tower bolts 200mm long, powder coated, of extruded section and fixed, complete all as specified and directed. |
| 78 | Supply and fix, Aluminium alloy, anodised, Sliding door bolts 200mm long, with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy 12mm dia, complete all as specified and directed. |
| 79 | Supply and fix 140mm size Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, complete all as specified and directed. |
| 80 | S&F Galvanised stain steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed. |
| 81 | Supply and Fix, powder coated door seal fixed with screws to any type of shutter, complete all as specified and directed. |
| 82 | M&L for repairing any type of aluminium/wooden door shutter exc. 1.5 sqm but n .exc. 1.5 sqm and refixing in the same opening after resecuring its frame work by means of tightening with necessary arrangement andnew screws of by aluminium angle cleat,complete all as specified and directed. |
| 83 | M&L for repairing any type of aluminium/wooden window shutter n .exc. 1.5 sqm and refixing in the same opening after resecuring its frame work by means of tightening with with necessary arrangement and new screws of by aluminium angle cleat, and roller for sliding window complete all as specified and directed. |
| 84 | M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with belding or necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangementcomplete all as specified and directed. |
| 85 | M&L for prepration of old surfaceincluding by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil, greasy spots and of wall and applying onecoat of oil bound distemperwhite or tinted over1mm thick wall care putty (where as requird) , to be applied using an airless spray machine, after covering of window glass,door shutter and electric point/ appliances with help of polythene/news paper complete all as specified and directed by Engr-in-Charge. |
| 86 | M&L for preparationof old surface of wall, chajja, facia including by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil, greasy spots of wall and leveling / edgesing the disturbed surface with water proofing putty and applying two coat of exterior acrylic emulsion weather proof treatment upto 15 Metre height to be applied using an airless spray machine including necessary scaffolding etc complete all as specified and directed. Note : The tint and shade be as approved by the GE. |
| 87 | S&F Gun-metal, globe or gate valves, with iron wheel head, 20 mm bore screwed both end for iron pipe, and fixed complete all as specified and directed by Engr-in-Charge. |
| 88 | S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and CP waste coupling and 40 mm PVC waste pipe; including bedding in cement mortar to dwarf wall or including fixing cantilever 03 nos brackets of angle 30mm x 30mm, thickness 3-4mm, 500mm long with PCC 1:2:4 B0 in wall and connecting union to pipe overall size 914mm x 460mm bowl size 410mm x 330mm x 203mm fixed. |
| 89 | Dismantling brick tiles or terracing tiles, single layer on roof and removal of unserviceable brick tiles / brick bats of rubbish outside defence land upto a distance exc 1.5Km but n.exc 5Km, complete all as specified and directed. |
| 90 | Taking down existing bitumen felt (any layer) including cement mortar bedding padding and cleaning the surface and removal of all rubbish outside defence land upto a distance exc 1.5Km but n.exc 5Km, complete all as specified and directed. |
| 91 | Demolition of mud in roofs, any thickness, including plastering and leeping (weather full thickness removed and demolished upto mother slab) complete all as specified and removal of all rubbish outside defence land upto a distance exc 1.5Km but n.exc 5Km, complete all as specified and directed. |
| 92 | M&L for PCC 1:2:4 type B-0 (12.5 mm graded crushed stone aggregate) as in padding on roof laid in 40mm thick average required thickness to maintain desired slope, finished even and fair without using extra cement, complete all as specified and directed. |
| 93 | M&L for rendering 15mm thick in cement mortar (1:3) usingWPC @200ML per 50Kg bag of cement on surfaces of roof and parapet, finished even & fair without using extra cement, complete all as specified and directed.Note :- WPC shall be measured and paid separately. |
| 94 | Supply only Liquid water proofing compound complete all as specified and directed by Engr-in-Charge. |
| 95 | M&L Plain cement concrete B-0 type (1:2:4) using 12.5 mm graded crushed stone aggregate as in copings, bed plates, benching and the like finished fair & even, including necessary form work complete all as specified and directed by Engr-in-Charge. |
| 96 | M&L for cleaning the surface before final treatment on roof as specified, applying the double layer of glass fibre mesh of 60 GSM over the roof using poly plastic fibre adhesive mix in the following manner :-(a)Making poly plastic fibre adhesive mix by adding polyplastic fibre white cement in equal portion and add 25% water in it to make the mixture asper manufacturer instructions. (b)The double layer of fibre mesh to be spread on the roof & apply two coat of above mixture of poly plastic fibre adhesive with a rolle & brush to cover the fibre mesh throughouly. (c)Process of roof lamination:- Lamination/top coat on the roof using poly plastic fibre coat with white cement & water as per manufacturer instructions. Top coat is ammonia free, w/o any harmful effects, & is flexible in nature. (d)Min thickness of the treatment shall be 2mm. |
| 97 | All as per Srl item No. 96.00 here-in-before but as in chajjas. |
| 98 | M&L for removal of paint/putty etc from the wall using mechanical means as per manufacturer instructions. Hacking of existing plastered surfaces upto 2mm.Note :- The wall treatment shll be done on hacked/new cementous surface for proper bonding & requsite results. Surface to be treated shall be passed by Engr-in-Charge. (a) Take Poly plastic fibre adhesive, white cement in equal proportion & add 25% water in it to make the mix as per manufacturer instructions. Apply 2 coats of wall bind adhesive mixture to the wall using a roller & brush.(b) Final & top coat apply with mixing ratio of poly plastic fibre top coat & water & white cement as per manufacturer instructions. For ser No 96, 97, 98 & 99.Note :- The poly fibre plastic should have following characterstics :-(a) Resists positive hydrostatic presure of upto 14 bars.(b) Crack filling ability upto 45 mm.(c) Temp control upto 14 degree celcious on any surface like concrete roof, metal shed & for walls also.(d) High durablity to water, fire & UV rays covering climate condition to + 55 degree celcious. |
| 99 | All as per Srl item No. 98.00 here-in-before but treatment over the plastered surface of wall and parapet including cleaning of surface. |
| 100 | M&L for disconnecting of PVC tank of capacity n.exc 500 litres or cleaning including setting aside temporarily and refixing later in same position for water supply to enable water proofing treatment of roof slab beneath the tank in following laid down process all as specified and directed :-a) Dewatering & removing all settled silt, scale & dust from inside of tanks using coconut brush manually and applying bleaching powder and allowed to rest for 1 hour.b) Cleaning& rinsing the tank using fresh water to wash out complete and allowed to dry for 30 mins.c) Writing letters of 7 cm height using synthetic enamel paint (white colour) to mention date of cleaning incl rubbing out old letters written over the tank.d) Refixing the tank with fittings as required in same position or raised/lower height after cleaning or water proofing treatment (as may necessary) complete all as specified and directed. (e) Alternate arrangement of water to be provided by bidder for user during the executionof work.(f) All GI/ CI/ PVC/ CPVC pipe fitting of any dia will be removed from roof/wall and refixed after the job done. |
| 101 | M&L for disconnecting of PVC tank of capacityexc 500 Ltrs but n.exc 1000 Ltrs for cleaning including setting aside temporarily and refixing later in same position for water supply to enable water proofing treatment of roof slab beneath the tank in following laid down process all as specified and directed :-a) Dewatering & removing all settled silt, scale & dust from inside of tanks using coconut brush manually and applying bleaching powder and allowed to rest for 1 hour.b) Cleaning& rinsing the tank using fresh water to wash out complete and allowed to dry for 30 mins.c) Writing letters of 7 cm height using synthetic enamel paint (white colour) to mention date of cleaning incl rubbing out old letters written over the tankd) Refixing the tank with fittings as required in same position or raised/lower height after cleaning or water proofing treatment (as may necessary) complete all as specified and directed. (e) Alternate arrangement of water to be provided by bidder for user during the executionof work(f) All GI/CI/PVC/CPVC pipe fitting of any dia will be removed from roof/wall and refixed after the job done. |
| 102 | S&F for in repair stainless steel curtain rod heavy type chromium plated with fixing brackets, stpos, roller, latu etc complete all as specified and directed. |
| 103 | S&F75mm Hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plateand fixed with screwsetc complete all as specified and directed. |
| 104 | M&L for teak wood lipping fixed to 18/19mm board with nails/adhesive complete all as specified and directed. |
| 105 | Taking down existing copper /aluminium conductor point wiring(light, fan, socket or power) complete including fixtures and fittings such as switches ceiling roses pendants, bell, buzers, regulators sockets etc and removing materials to store for keeping in safe custody or for taking credit and making good disturbed surface of walls, ceiling etc complete all as specified and directed. |
| 106 | M&L for Concealed Point wiring with 1.5 Sqmm (nominal area) single core PVC insulated unsheathed (FRLS) cable, multi-stranded, copper conductor, inuniversal colour code with & including suitable size of rigid non-metallic UPVC conduit (not less then 20mm dia med gd)and its all accessories complete concealed in wall / roofincl cutting & chases and modular flush metal boxes 0.8 mm thicksuitable for modular fittings including modular outercover plate outer Mirror/glass finish of make Legrand (Arteor)/Schneider (Zencelo) /Anchor (panasonic Thea)/Goldmedal(GIFA Z9)) with inner frame suitable for cover plate as per site requirementfor mounting modular switches, sockets,etcincluding earth wire ofPVC insulated (FRLS) copper conductor multistrandedof 1.5Sqmmsize in green colour completeby making good disturbed surface (i.e plastering, one coat of putti and two coats of interior emulsionpaint with matching existing surface) complete all as specified and directed. |
| 107 | One light point/ Ceiling/ Exhaust Fan point controlled by one way modular switch 6 Amp complete. |
| 108 | One 3 pin 6 Amp socket point controlled by one modular switch on same board. |
| 109 | One 3 pin 6 Amp socket point controlled by one Modular switch on independent board. |
| 110 | One bell point controlled by one Modular switch. |
| 111 | All as per Srl item No. 106 here-in-before but for 3 pin / 5 pin 16 Amp sockets outlet with 2.5 Sqmm PVC insulated & unsheathed (FRLS) copper conductor cable independent and 2.5 Sqmm PVC insulated & unsheathed (FRLS) copper conductor cable for earth wire complete all as specified and as directed. |
| 112 | Supply and Fixing Modular switch mirror finish 16/20 Amp single pole one way, 2 Module with indicator and no top gap between rocker plate and fully shrouded double rocker mechanisam type all the importent parameters like rating etc should be laser printed on every switch along with catoulage numberall as specified. Make: Legrand (Arteor) / Schneider (Zencelo) / Anchor (Panasonic Thea) /Goldmedal (GIFA). |
| 113 | Supply and Fixing Modular socket mirror finish shutter type, 2-in-1, 3 and 5 pins 6 /16 Amps, combined 2 Module and no top gap between rocker plate and fully shrouded double rocker mechanism type all the important parameters like rating etc should be laser printed on every switch along with catalogue number complete all as specified. Make : Legrand (Arteor) / Schneider (Zencelo) / Anchor (Panasonic Thea) / Goldmedal (GIFA). |
| 114 | Supply and Fixing Modular ceiling rose surface bakelite, square in shape 100 mm x 100 mm three terminals complete all as specified. |
| 115 | Supply and Fixing in replacement Modular switch 6 Amps single pole one-way, 1 Module mirror finish and no top gap between rocker plate and fully shrouded double rocker mechanism type all the important parameters like rating etc should be laser printed on every switch along with catalogue numbercomplete all as specified. Make : Legrand (Arteor) / Schneider (Zencelo) / Anchor (Panasonic Thea) / Goldmedal (GIFA). |
| 116 | Supply and Fixing in replacement Modular socket shutter type, 2-in-1, 3 pins 6 Amps, ISI marked, combined 2 Module and no top gap between rocker plate and fully shrouded double rocker mechanisam type all the importent parameters like rating etc should be laser printed on every switch along with catoulage number complete all as specified. Make : Legrand (Arteor) / Schneider (Zencelo) / Anchor (Panasonic Thea) / Goldmedal (GIFA). |
| 117 | Supply & Fixing in replacement Modular fan Regulator electronic step type 100 watt, ISI marked, 2 Module, 8 steps complete all as specified. Make : Legrand (Arteor) / Schneider (Zencelo) / Anchor (Panasonic Thea) / Goldmedal (GIFA). |
| 118 | Supply and Fixing Modular bell push 6 Amps single pole, 1 Module suitable for Mirror/Glass finish modular cover plateand no top gap between rocker plate and fully shrouded double rocker mechanism type all the important parameters like rating etc should be laser printed on every switch along with catalogue number complete all as specified. Make : Legrand (Arteor) / Schneider (Zencelo) / Anchor (Panasonic Thea) / Goldmedal (GIFA). |
| 119 | S&F Modular bell ding dong, 230V, 2 Module, Concealed in wall with concealed metal sheet steel enclosure (same as per bell make) with inner mounting frame and outer modular mirror/Glass finish cover for mounting including making good (i.e plastering, one coat of putti and two coats of interior emulsion paintpaint with matching existing surface), complete all as specified and directed. Make : Legrand (Arteor)/ Schneider (Zencelo)/ Anchor (Panasonic Thea)/ Goldmedal (GIFA Z9). |
| 120 | Supply & fixing in replacement indoor decorative ultra slim surface /Wall mounted T5 LEDbatten tube light complete fitting 1 x 20 watt LED Tube fittingwith polycarbonate channel housing & integrated electronic driver, energy efficient, 140V-270 volts, complete all as specified and directed. Make :- Philips/ Jaquar/ Havells. |
| 121 | Supply and fixing in replacement of 02 feet 10 Watt LED Batten with extruded aluminimum housing with high quality PC diffuser complete all as specified and directed by Engr-in-Charge. Make :- Philips/ Jaquar/ Havells. |
| 122 | Supply and fixing of water storage heater vertical (geyser) with inner Tank Material : Blue Diamond Glass Lined Tank- 2X Corrosion Resistance, Outer Body Material : ABS, Type : Storage, Capacity : 25 Litres, AC 220-240 Volts, Wattage : 2000 Watts with auto temperature cutoff, Pressure : 8 Bars, BEE Rating : 5 Star complete all as specified and directed.Make : Gold Medal (G Hydro)/ Havells (Magnetron)/ Jaguar (Elena). |
| 123 | Supply and fixing304 Grade SS Connection Pipe for geyser hot and cold water, Hose Pipe(45 cm) with nuts and washers and gaskets etc complete all as specified and directed. |
| 124 | Supply and fixing MCB protected modular socket with Modular MCB 16 Ampsbuilt in Modular MCB + Modular Socket 16 Ampswith concealed metal sheetsteel enclosure 0.8 mm thick (Same as per Socket Make) with inner mountingframe and outer Mirror/glass finish modular cover 3 Modulefor mountingby making good disturbed surface (i.e plastering, one coat of putti and two coats of interior emulsion paint with matching existing surface) complete all as specified and directed. Make : Goldmedal (GIFA Z9)/ Legrand (Arteor)/ Anchor (Panasonic Thea)/ Schneider (Zencelo). |
| 125 | Supply and fix Exhaust fan 250 mm sweep non metallic type alongwith louvers and detachable front PVC grill complete suitable to work on AC, single phase, 230 Volts, 40 W, 1250 RPM, 750 CMH, 50 Hz supply and including making suitable hole connecting up with three core twisted flexible copper conductor cable of suitable size 0.75 Sqmm all as specified and directed. |
| 126 | Supply and fix Exhaust fan 300 mm sweepmetallic type alongwith GI louvers and metallicfront grill complete suitable to work on AC, single phase, 230 Volts, 1200 RPM,1300 CMH, 70W, 50 Hz supply and including making suitable hole andconnecting up with three core twisted flexible copper conductor cable of suitable size 0.75 Sqmm all as specified and directed. |
| 127 | Supply and fixing PRCD Top Plug 3 Pin, 16 Amps, 30 mA all as specified and directed. |
| 128 | Supply and fixing in replacement of MCB Single pole 6 to 32Amp, 240V, 10KA, \"C\" integrated label holder, sliding bottom clamp, color coded On/Off indication on dolly, with efficient air chanels etc complete all as specified.Make : Havells/ Legrand/ Goldmedal. |
| 129 | Supply and fixing in replacement of MCB DB Single pole and neutral 12 way, double door, sheet steel phospehtised powder painted (White colour) withIP 43 protection 240 V neutral link, earth bar and Din rail complete all as specified and directed. Make : Legrand/ Havells/ Goldmedal. |
| 130 | Supply and fixing Arc Fault Detection Device (AFDD) with RCBO 32 Amp combined SPN MCB + AFDD+RCCB, offering protections for overload, short circuit, reidual current characteristices type A, over voltage protection above 270V AC +/- 5% & series, parallel arc fault, AFDD must be with dual test button for AFDD and earth leakage functions along with single diagnostic LED with blinking patterns for continious ON series arc parallel arc & over voltage protections. Make : Havells/ Legrand/ ABB. |
| 131 | Note :- Amount of credit ofRs. 17585.00for retrieved materials is mentioned in Schedule of Creditof tender documents in pdf form which will be deducted offline while acceptance of tender. |
