|
| 1 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 2 | Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.Two coats |
| 3 | Removing dry or oil bound distemper, water proofing cement paintand the like by scrapping, sand papering and preparing the surfacesmooth including necessary repairs to scratches etc. complete.smooth including necessary repairs to scratches etc. complete. |
| 4 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :One or more coats on old work |
| 5 | Finishing walls with Premium Acrylic Smooth exterior paint withSilicone additives of required shadeOld work (Two or more coats applied @ 1.43 ltr/ 10 sqm) over existing cement paint surface |
| 6 | Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below:1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos.2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs.3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs.4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time.) |
| 7 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Treatment at points of contact of wood work by chemical emulsion Chlorpyriphos/ Lindane (in oil or kerosene based solution) @ 0.5 litres per hole by drilling 6 mm dia holes at downward angle of 45 degree at 150 mm centre to centre and sealing the same. |
| 8 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes |
| 9 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: -35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 10 | Providing and fixing Stainless steel tower bolts, ISI marked, transparent or dyed to required colour or shade, with necessary screws etc. complete : 200x10 mm |
| 11 | Providing and fixing Stainless steel handles, ISI marked, transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm |
| 12 | Providing and applying Vineratex OFResin Bonded Ready Mixed Ready to use Decorative Textured coating of Natural Stone finish \"Vineratex\" of approved of approved shade and colour. Dry film of the average thickness of 2 mm of 2.5 mm on recommended plaster specifications; to perfect line,level,plump including finishing with sharp edge at corners, nitches etc all as per manufacturers recommendations and specification including all labour materials, scaffolding and surface preparation etc. upto 12.50 mtr heightcomplete as specified in drawing and as directed by the Engineer-In-Charge. |
| 13 | Providing and fixing factory made Carcass Material -18mm thick HDHMR with 0.8 mm laminate fabric, Shutter material- Hi-gloss 1.5mm Acrylic Shutter - back side carcass finish on 18mm HDHMR, Handle -Floor shutter- G profile, Wall shutter- 20mm drop down, Hardware- fittings - innotech drawer, German soft closing hinges, PVC cutlery, Dish rack, DPO, Wastebin holder, BPO, Gas lift up, Internal Glass drawers, Glass- Aluminium profile with Brown tinted glass, all items complete all respect as per attached drawing with the direction of Engineer -in charge.1. Innotech Drawer 4\" = 03 each2. Innotech Drawer with Gallery = 06 each3. German Soft close Hinges = As per required4. PVC Cutlery 500 mm = 01 Each5. Wastebin Holder = 01 Each6. DPO Basket = 01 Each7. Dish rack 900mm = 01 Each8. BPO 300 mm = 01 Each9. Gas lift up = 02 Each10. Internal Glass Drawers for Pantry = 04 Each11. Stainless steel wire basket = 02 nos 12. G- Profile = As required 13. Pvc board for for Granite base = As required14. Pvc Skirting and legs 100 mm = As required |
| 14 | Cost after adjustment on account of GST corrections factor |
| 15 | Cost Index @3% |
