|
| 1 | (A:CIVIL WORKS ) |
| 2 | Sub-Head 1:-Earth Work |
| 3 | Earth work in excavation in foundation trenches or drains including dressing of sides ramming of bottoms lift up to 1.5 metres including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 metres |
| 4 | Fillingavailable excavatedearth (excluding rock) in trenches , plinth side of the foundation etc. in layers not exceeding 20 cm in depth ,consolidating each deposited layer by ramming and watering lead up to 50 metres and lift upto 1.5 metres |
| 5 | Supply and filling in plinth with sandy soil under floors including watering, ramming consolidating and dressing complete |
| 6 | Sub-Head 2:-Concrete & RCC Work |
| 7 | Providing and Laying in position cement concrete of specified grade excluding the cost of centering & shuttering ,1:4:8(1cement:4coarse sand : 8 graded stone aggregate 40 mm nominal size). |
| 8 | Providing and laying in position ready mixed plain concrete or site batched design mix cement concrete for reinforced cement concrete work,using coarse aggregate and fine aggregate derived from naturalsources,Portland Pozzolana/Ordinary Portland /Portland slag cement,admixture in recommended proportions as per IS:9103 to accelerate / retard setting of concrete , to improve ductility and workability without imparting strength;including pumping of concrete to site laying, curing, carriage for all leads, but excluding the cost of centering, shuttering, finishing and reinforcement as per directionofEngineer-in-charge;for the following grades of concrete:All works upto plinth Level: Concrete of M25 grade with minimum cement content of 330kg/cum |
| 9 | Providing and laying in position ready mixed plain concrete or site batched design mix cement concrete for reinforced cement concrete work,using coarse aggregate and fine aggregate derived from naturalsources,Portland Pozzolana/Ordinary Portland /Portland slag cement,admixture in recommended proportions as per IS:9103 to accelerate / retard setting of concrete , to improve ductility and workability without imparting strength;including pumping of concrete to site laying, curing, carriage for all leads, but excluding the cost of centering, shuttering, finishing and reinforcement as per directionofEngineer-in-charge;for the following grades of concrete:All works above plinth Level: Concrete of M25 grade with minimum cement content of 330kg/cum |
| 10 | Reinforced cement concrete work in beams,suspended floors, roofs having slope upto 15 deg landings, balconies, shelves,chajas, lintels, bands,plain window sills, staircase and spiral staircases above plinth level upto floor five level, excluding the cost of centering, shuttering, finishing, and reinforcement with 1:5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregates 20 mm nominal size). |
| 11 | Providing and laying damp proof course 50 mm thick with concrete cement 1:2:4(1 cement : 2 course sand : 4 graded stone aggregate 20 mm nominal size) |
| 12 | Applying a coat of residual petroleum bitumen of penetration 80/100 of approved qualit yusing 1.7kg per sqm on damp-proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in Kerosene oil. |
| 13 | Sub-Head 3:-Reinforcement Steel/ Rebar work |
| 14 | Steel reinforcement for RCC work i/c straightening , cutting , bending , placing in position and binding all complete upto plinth Level.Thermo MechanicallyTreated Bars |
| 15 | Steel reinforcement for RCC work i/c straightening , cutting , bending , placing in position and binding all complete above plinth Level.Thermo MechanicallyTreated Bars |
| 16 | Sub-Head 4:-Brick work |
| 17 | Brick work with 1st class common burnt clay F.P.S (non modular) bricks in foundation and plinth in:cement mortar 1:4 (1 cement: 4 coarse sand) |
| 18 | Half brick masonry with first class common burnt clay F.P.S. (non modular) bricks in superstructure above plinth level upto floor V level in Cement mortar 1:4 (1 cement: 4 coarse sand) |
| 19 | Sub-Head 5:-Form work |
| 20 | Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof 12mm ply |
| 21 | Columns, pillars, Piers, Abutments, Posts and Struts. |
| 22 | Sub-Head 6:-Flooring work |
| 23 | 52 mm thick concrete flooring with concrete hardener toping under layer 40mm thick cement concrete 1:2:4 (1 cement:2 coarse sand :4 graded stone aggregates of nominal size 20 mm) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix :2 graded stone aggregates 6 mm nominal size ) by volume hardeneing compound is mixed @ 2lit per 50 kg of cement or as per manufacturers specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete. |
| 24 | Sub-Head 7:-Wood/PVC work |
| 25 | Providing woodwork in frames of doors, windows, celestory windows and other frames wrought, framed and fixed in position with hold fast lugs or with dash fastner of required dia and length (hold fast lugs or with dash fastner shall be paid separately) with Local best quality Tolhao wood. |
| 26 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked MS pressed butt hinges bright finished of required sizes with necessary screws with Local best quality Tolhao wood 30mm thick |
| 27 | Providing and fixing aluminium sliding bolts ISI marked anodised (anodic coating not less than garde AC 10 as per IS 1868) transparent or dyed to required colour or shade with nuts nad screws etc complete with 300x16mm |
| 28 | Providing and fixing aluminium Tower bolts ISI marked anodised (anodic coating not less than garde AC 10 as per IS 1868) transparent or dyed to required colour or shade with nuts nad screws etc complete with 250x10mm |
| 29 | Providing and fixing chromium plated Brass handles with necessary screws etc.complete. |
| 30 | Providing 40x3mm flat iron hold fast 40cm long I/c fixing to framed with 10 mm dia .bolt nuts and windows plugs and wooden plugs and embedding in cement concrete block 30x10x15mm 1:3:6(1cement:3 coarse sand:6 graded stone aggrt.20mm nominal size) |
| 31 | Sub Head 8: Roofing work/Steel Work |
| 32 | Steel work in built up tubular (round, square, or rectangular tubes etc) trusses etc, including cutting, hoisting fixing in position and applying a priming coat of approved steel primer, including welding and bolted including special shaped washers etc complete with Hot finished welded type tubes. |
| 33 | Providing and fixing precoated galvanised iron profile sheets (size, shape, and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120gsm as perIS:277, in 240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and poluester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desire by Engineer-in-charge. The sheet shall be fixed using self drilling/ self tapping screws of size (5.5+55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with Precoated galvanised iron profile sheets 0.35mm thick/4.2Kg/sqm |
| 34 | Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120gsm as per IS:277 in 240mpa steel grade 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, GI plain and bitumin washers complete: |
| 35 | Ridges plain(500-600mm), Precoated galvanished iron profile sheets 0.35mm thick |
| 36 | Gutter(500-600mm), Precoated galvanished iron profile sheets 0.35mm thick |
| 37 | Providing and fixing on wall face unplasticised- PVCmoulded fittings/accessories for sunplasticised-Rigid PVC rain water pipe conforming to IS:13592 Type A including joining with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion.Single push fit Coupler:75mm |
| 38 | Sub Head 9: Accessories |
| 39 | P/F M.S. fan clamps type-I or II of 16mm dia. and M.S.bar bent to shape with hooked ends in RCC slabs, beams during laying including painting the exposed portion of loop, all as per standard design complete. |
| 40 | (B:INTERNAL ELECTRIFICATION AND INSTALLATION ) |
| 41 | 6A Socket |
| 42 | 16A Socket |
| 43 | 16A Switch |
| 44 | 12 way metal box |
| 45 | 12 way modular plate |
| 46 | 6W Metal Box |
| 47 | 6w Modular Plate |
| 48 | Fan regulator switch type |
| 49 | Surface Light |
| 50 | Fan regulator switch type |
| 51 | 6A switch |
| 52 | Fan Box |
| 53 | Deep JB 4 way |
| 54 | Conduit pipe 25 mm |
| 55 | Wire 1.5 sqmm Red |
| 56 | Wire 1.5 sqmm Blue |
| 57 | Wire 1.5 sqmm Green |
| 58 | Wire 2.5 sqmm |
| 59 | Wire 4 sqmm Red |
| 60 | Wire 4 sqmm Blue |
| 61 | Wire 4 sqmm Green |
| 62 | (C:INTERNAL WATER SUPPLY AND SANITARY INSTALLATION) |
| 63 | Providingandfixing waterclosetsquatting pan (Indian type W.C. pan) with 100 mm sand cast IronP or S trap, 10 litre low level white P.V.C. flushingcistern,includingflushpipe,withmanuallycontrolleddevice(handle lever) conforming to IS: 7231, with all fittings andfixturescomplete,includingcuttingand makinggoodthewallsandfloorswherever required:White Vitreous china Orissa pattern W.C. pan of size 580 x 440 mm with integral type footrests |
| 64 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with CI Brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required:Kitchen sink without drain board:610x460 mm bowl depth 200mm. |
| 65 | Providing and fixing wash basin with CI brackets, 15mm dia CP brass pillar taps, 32 mm C.P brass waste of standard pattern, including painting offittings and brackets, cutting and making good the walls wherever required: White vitreous china wash basin size450x300 mm with a pair of 15mm CP brass pillar tap. |
| 66 | Providing and fixing PTMT Waste Coupling for wash basin and sink of approved quality and colour. Waste coupling 38 mm dia of 83 mm length and 77 mm breadth, weighing not less than 60 gsm |
| 67 | Providing and fixing PVC waste pipe for sink or wash basin including PVC waste fittings complete.24.37.1 Flexible pipe: 40mm diameter |
| 68 | Providing and fixing 600 x 450 mm levelled edge mirror of Indian make superior glass (of approved quality) quality complete with asbestos sheet ground, fixed to wooden cleat with C.P. brass screws and washers. |
| 69 | Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings arrangement of approved quality and colour, weighing not less than 105gms |
| 70 | Providing and fixing CPVC. pipes having thermal stability for hot o& cold water supply ,including all CPVC plain & brass threaded fotting, including fixing the pipe with clamps at 1.00 m spacng.This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in charge.25 mm diameter |
| 71 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS:12701 marked,with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but withou fittings and the base support for tank. |
| 72 | Providing and fixing PTMT extension nipple fro water tank pipe, fittings of approved quality and colour.25 mm nominal bore weighing not less than 62 gms |
| 73 | Steel Work For Elevated Water Tank Stand: |
| 74 | Structural steel work in single section fixed with or without connecting plate including cutting,hoisting, fixing in position and applying coat of approved steel primer all complete: |
| 75 | Ready Made Septic Tank |
