|
| 1 | Removing existing water proofing treatment by brushing with wire brush, taking down cement concrete tile, existing plaster/cement concrete/lime coba etc in any thickness, cleaning of all foreign material such as fungus, moss, dust etc and remove from the site of all waste materials, roughing surface of corner to roof by wire brush and all the open cracks/honeycomb should repair properly with site made polymer mortar (cement: sand: 1:4) admixed with HS Latex Plus @10% by weight of cement. complete all as specified and directed. |
| 2 | M&L for 10 mm thick rendering on roof/wall in cement mortar 1:4 on concrete/brick surfaces when concrete is stilgreen finished even and fair including mixing ofwater proofing compound as per manufacturer instructionetc complete all as specified and as directed.Note :- Water proofing compound shall be measured separately |
| 3 | Supply only integral water proofing compound complete all as specified and as directed. |
| 4 | Cutting grooves in brick wall 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and as directed. |
| 5 | M&L applying water proofing treatment with the following:-(a) First coat of bitumen primer conforming to IS-3384 @ 0.3Kg / sqm to be applied on prepared surface till the surface is properly impregnated.(b) after the application of approved bituminous primer the water proofing memberne minimum weight 3kg/sqm and minimum 3mm thick reinforced with polyesterd non woven fabric (weight not less then 160gms/sqm) shall be laid on the primed surface by torch application method as per manufactured instruction.(c) All joints and change in direction should be curved with cement mortar (1:3) mixed with SBR latex @ 200ml per bag on cement and cured well before laying of membrane including Aluminium paint on top surface |
| 6 | Taking down plaster on brick or stone wall, ceiling etc incl racking out joints hacking for keys scrubbing down with water etc complete all as specified and directed. |
| 7 | M & L 10 mm thick rendering on other than fair faces of brick work or concrete surface in cm 1:6 to be finished fair and even with out suing extra cement. |
| 8 | M&L for external rendering 15 mm thick in CM 1:4 on brick work or concrete surfaces of wall finished even and fair complete all as specified . |
| 9 | M & L for complete removal of existing treatment from surface ofwall all as specified and as directed by the Engineer-in-Charge |
| 10 | M & L for applying water proof 2 mm putty on wall in 2 layer (each layer should be 1 mm)all as specified and as directed by the Engineer-in-Charge |
| 11 | M& L for two coat of exterior emulsion acyrlic weather proof antifungal paint over a coat of exterior grade primer on old/new plastered surface including preparation of surface complete all as specified and as directed |
| 12 | M & L for applying two coat of oil bound distemper all as specified and as directed by the Engineer-in-Charge |
| 13 | M & L for preparation of oldceiling surfaces and applyingtwo coats of white wash complete all as specified and directed. |
| 14 | S&F in repair Vitreous china squatting pan, \"orissa\" pattern, size 580 x 440 mm white, with integral footrest (excluding flushing cistern and flush pipe) including provision of concrete beddig and joint to flush pipe to squatt pattern closet including all joints and making good to the floor and taking down old one complete all as specified and as directed. |
| 15 | S&F in repair 10 Ltrs capacity PVC flushing cistern valveles syphonic action type low level, white, with inlet ball valve, float & handle incl brackets & flush pipe complete all as specified and directed. |
| 16 | S&F in repair EWC (Pedestal Pattern) cascade type with glazed flush tank, seat cover etc white including fixing bolts complete including making good to floor to match with adjoining surfaces and taking out existing water closet all as directed by Engineer-in-Charge. Make -Somani or equivalent make as given in Appendix B to PS. |
| 17 | S & Fin repairVitreous China Urinal (360x345x570mm), white including fixing kit, flushing cistern, flush pipe and bottel trapcompleteall as specified and as directed ,Make:Parryware(C05801C) or equivalent make as given in Appendix B to PS. |
| 18 | S & Fin repair toughened polish glass partition for urinal ,size 900mm x 450mm, 8 to 10 mm thick including fixing kit completeall as specified and as directed. |
| 19 | S & F in repair table top white vitreous china wash basin(510x350x120mm) of specified size and model including 32 mm dia waste coupling , CPwash bashin mixer(hot and cold) having long neck and aerator complete including making necessary holes and other cutting in the counter top and fixing the wash bashin etc completeall as specified and as directed |
| 20 | S&F in repair stainless steel sink with drainage board made of 1.00 mm thick steel sheet for kitchen or laboratory with plug, waste pipe, coupling, washers also incl cantilever cast iron brackets connecting union etc, overall size 915x460mm with bowl size 410x330x160mm complete all as specified and as directed . |
| 21 | S&Fin repair PVC connection 15mm size with PTMT nuts of length 600mm complete all as specified and as directed . |
| 22 | S&F in repair 15 mm stop valves angular type, cast copper alloy, screwed down, high pressure with crutch or butter fly handlescrewed both endsforiron pipe or for unionsand fixed complete all as specified and as directed . |
| 23 | S&Fin repair brass chromium plated tubular towel rail, 20 mm dia, D type, 60cm long between flangs complete all as specified and as directed. |
| 24 | S&F in repairs 15mm bore fancy type chromium plated bib taps long body with crutch of butterfly handle screwed down for iron pipes complete all as specified and as directed. |
| 25 | S& F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete as specified. |
| 26 | S&F in repair CP Brass soap dish fixed to wall with cp brass screws etc complete all as specified and as directed by the Engineer-in-Charge. |
| 27 | S&F in repair stainless steel kitchen plate rack overall size 900mm x 900mm make out of 1mm thick stainless steel sheet etc complete. |
| 28 | S&F in repair chromium plate curtain rod with CP brackets and knobs at both end as per sample approved by Engineer-in-charge. |
| 29 | S&F in repair Rectangular LED bathroom mirror (900mmx600mmx6mm) with touch sensor switch,bevelled edge mirror of selected quality glass, mounted on wall and fixed to plastic plugs with chromium plated brass screws and cup washers complete all as specified and directed |
| 30 | S&Fin repaircast copper alloyCP toilet paper holder fixed to wall etc complete all as specified and as directed . . |
| 31 | S &F in replacementglass shelf assembly consisting of 5.5mm thick sheet glass 12 cm wide with CP bracket guard and railing 60cm long fixed to wall with screws in position complete all as directed . |
| 32 | S &F in repair of 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed. |
| 33 | S&F in repairPVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed on walls , 110 mminetrnal bore ,etc complete all as specified and direcetd . |
| 34 | S &Fin repairof 75mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors or walland complete all as specified and directed. |
| 35 | S&F PVC (SWR) bends any radius 110mm bore complete all as specified and as directed . |
| 36 | S&F PVC (SWR) bends any radius 75mm bore complete all as specified and as directed . |
| 37 | S&F PVC (SWR) junction single, (single T) equal or unequal 110mm bore with access door complete all as specified and as directed . |
| 38 | S&F PVC (SWR) vent cowl 110mm bore complete all as specified and as directed . |
| 39 | S&F in repair PVC floor trap/Nahani trap outlet dia 75mm with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed |
| 40 | Dismantling water tanks and removing to store of capacity exc 500 & n.exc 1000ltrs etc complete all as specified and directed. |
| 41 | S&F 500 ltr capacity rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) ,WHITE , ISI marked , Triple layered construction , hoisted and fixed in position including S&F 20mm dia GI pipe medium grade washout pipe 450mm long with plug and 20mm dia GI pipe medium grade overflow pipe 600mm long with fitting etc complete all as specified in SSR Part -I 2009 complete all as specified and as directed. |
| 42 | S&F 1000 ltr capacity rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) ,WHITE , ISI marked , Triple layered construction , hoisted and fixed in position including S&F 20mm dia GI pipe medium grade washout pipe 450mm long with plug and 20mm dia GI pipe medium grade overflow pipe 600mm long with fitting etc complete all as specified in SSR Part -I 2009 complete all as specified and as directed. |
| 43 | S&F ball valves of 20 mm bore high pressure of PTMT with empxy coated aluminium rod and high density plastic ball screwed for iron pipe & fixed complete all as specified and as directed(Minimum weight 20 gms-210 gms) complete all as specified and as directed |
| 44 | S & F in repairs 20 mm dia Gun Metal, globe or Gate Valve with Iron wheel head Screwed both ends for Iron Pipe and fixed in repairs including taking down the existing fitting complete all as specified and as directed. |
| 45 | Taking up or down steel tubing and connetion including cleaning for refixing or removing to store of 15mm bore of pipe, complete all as specified and directed. |
| 46 | Taking up or down steel tubing and connetion including cleaning for refixing or removing to store of 20mm bore of pipe, complete all as specified and directed. |
| 47 | S&F,15mm bore tubes medium grade galvanised with all fitting and fixed to walls and ceiling or laid in floor etc complete all as specified and as directed |
| 48 | S&F,20mm bore tubes medium grade galvanised with all fitting and fixed to walls and ceiling or laid in floor etc complete all as specified and as directed |
| 49 | Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc., and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cuttingexceeding 10 cm but not exceeding 20 cm girth in brick walls complete all as specified and as directed. |
| 50 | Material & Labour for writing letters or figures (block, Roman, Italic or Indian) n.exc.30 cm high complete all as specified and directed. |
| 51 | Demolition of Reinforced Cement Concrete ofRoofs,floors(otherthan ground floors), beams, staircases, landing, chajjas and similar suspended work completed all as specified and directed by Engr-in-Charge. |
| 52 | S&F Mild steelTMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and as directed . |
| 53 | M&L for providing precast reinforced cement concrete 1:2:4 type B1 using 20 m gradedstone aggregate as in landings, kitchen slab, cover slabs (for men holes etc) chullah hoods,chhajjas water troughs mangers,shelves and similar articles with plain faces complete all as specified and as directed . |
| 54 | M&L for Formwork (rough finished surfaces of concrete flat) to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed. |
| 55 | Dismantling floor, hearth or wall tiling including cement mortar bedding, (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed. |
| 56 | M&L 25mm thk PCC 1:2:4 type B-0 using 12.5 mm graded agg as in flooring finished fair and even without using extra cement complete all as specified and as directed. |
| 57 | M&L, screed bed or bedding layer of mortar 15 mm thick in cement mortar 1: 6 to receive tiles etc finished rough complete all as specified and directed. |
| 58 | M&LCeramic tiles(GVT double charge) light or dark shed(High glossy) 8-10 mm thick, (square/ rectangular),area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm,polished, in floors/wall etc.jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. |
| 59 | M&LCeramic tiles light or dark shed(Mat finish) 8-10 mm thick, (square/ rectangular),area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm,polished, in floors etc.jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. |
| 60 | M&LCeramic tiles light or dark shed(Mat finish)8-10 mm thick, (square/ rectangular),area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm,as in skirtingfixed over and including 10 mm thick cement screed in (1:4 ) CM set and jointed in neat cement slurryand pointed in white or coloured cement to match with the colour of tiles complete all as specified and directed. |
| 61 | Material & Labour glazed ceramic coloured tiles (High glossy) 1200x600x8-10 mm thick on skiriting/dado, set & jointed in neat cement slurry & pointed with white/coloured to match over 10mm thick bedding layer of mortar to wall in cm (1:4) for laying tiles on skirting/dado complete all as specified and as directed. |
| 62 | M&L for 18-20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite etc complete all as specified and directed. |
| 63 | Demolition of cement concrete(un Reinforced) of any description in any position not otherwise specifically provided for etc. complete all as specified and directed. |
| 64 | M&L Providing and laying 80mm thick high glossy factory made chamfered edge cement concretecoloured paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50 mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sandt complete all as specified and directed. |
| 65 | M&Lfor PCC 1:4:8 type D2 using 40mm graded stone agg as in filling and mass concrete, Sub base/flooring complete all as specified and directed. |
| 66 | M&L, for PCC 1:2:4 type B-0 using 12.5mm graded stone agg as in coping on side of path including necessary form work etc complete all as specified and directed. |
| 67 | M&L for 75 mm thick cement concrete type B2, 1:2:4 (40mm graded aggregate) as in floor/hardstanding finished even and smooth with using extra cement complete all as specified |
| 68 | Material and labour 75 mm thick PCC 1:3:6 type C2 using 40 mm graded aggregate as in plinth protection finished smooth and even w/o using extra cement and making good complete all as specified |
| 69 | Taking down chowkhats or frames with shutters ( without taking off shutters from froms exe 1.5 sqm and n.exe 4 sqmeach etc complete all as specified and as directed |
| 70 | Taking down chowkhats or frames with shutters ( without taking off shutters from froms n exe 1.5sqm each etc complete all as specified and as directed |
| 71 | Taking down Shutters of any description exc 2 sq. m each etc complete all as specified and as directed |
| 72 | Taking down shutters of any description exc 1 sqm and n.exc 2 Sqm each etc complete all as specified and as directed |
| 73 | M&L, aluminium powder coated/Anodised aluminiumframe for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed . |
| 74 | M&L foraluminium powder coated/Anodised aluminium door shutters,aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. S & F 5.5 mm thick tinted glass in panel of shutter fixed with glazing clips , rubber gasket and powder coated aluminium snap beading so as to make air tight and including S & F powder coated butt hinges type C-1,100 mm size 3 nos per shutter , powder coated aluminium handle of 150mm size 2 Nos (One on each side of shutter) , powder coated aluminium tower bolt of size 200 mm ( 2 Nos ) per shutter ,mortise lock , brass body ,6 levers ( 1 No) with duplicate keys, aluminium (extruded section) hydraulic door closer regulated designation No-3 Universal type ( 1 No) & Floor door stopper ( 140 mm ) overall ,aluminium body 1 No on each shtteretc complete all as specified and as directed. Note: (i) Shutter ( Glazed ) shall be fixed on frame of required size and shall be measured seperately (iii) Cost of all fittings & fixture shall deemed to be included in unit quoted rate by the tenderer . Note : The minimum thickness of powder coating shall be 50 Micron complete all as specified |
| 75 | Cutting holes in brick walls built in cement mortar for inserting hold fasts and making good dismantled portion in CM 1:3 or cement conc 1:2:4 type B1 as required exc half brick but not exc full brick wall complete all as specified and as directed. |
| 76 | M&L Bands, straps, supports or stays for rainwater, ventilating pipes,including bolts, if required:hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed . |
| 77 | Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) including outer frame upto 1.50m height made of including outer size frame 116 x 45 mm & sash 46 x 62 mm both having wallthickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension.comprising of uPVC multi chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 78 | S&F Rolled/hollow sections as in framing for wall cladding, glazing and the like fixed with angle cleats,hold fast, fashner and connecting plates with brick/concret etc. including distance pieces cleats etc of Fe-410-W (Gde -E-250) Quality B complete all as specified and as directed . |
| 79 | S&F6.3 mm thick, sheet glass in square in n exc 0.5 sq.m in each pane ordinary qualityand glazing/fixing with water resistence and heat resistence adhesive/glueetc complete all as specified and as directed. |
| 80 | M&L foraluminium powder coated/Anodised aluminium glazed window / ventilator shutter/wall partition, fixed type ,without sash bars usingapproved powder coated aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, powder coated aluminium snap beading, screwsall fittings, 5mm thick tinted ,selected quality and glass etc completeall as specified and as directed.Note : (i) The minimum thickness of powder coating shall be 50 Micron .(ii) Cost of all fittings & fixture shall deemed to be included in unit quoted rate by the tenderer . |
| 81 | M&L, framed work as grills, gratings, etc with ends of bars shouldered and/ or riveted into spikes; or forged into spikes, framed guard bars; barred iron doors and similar work confirming to Fe 290. Gd-E-165 etc complete all as specified and as directed |
| 82 | M&L Figured glass, pin head type 3 mm thick and glazingin squares not exceeding 0.5 Sqm in each pane fix with window shutter including necessary fixing arangemnt complete all as specified and as directed. |
| 83 | S & FFactory made solidPVC door frame of size 50 mm x 47 mm made out of 5 mmwood grain printed PVC sheet used reinforced with MS square tube instead of plain colour PVC sheet & edges will be painted to match with printed sheet complete all as specified and directed. |
| 84 | S&F Factory Made Solid PVC Moulded Door Shutter With Wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed. |
| 85 | S&F Butt hinges, extruded aluminum alloy with galvanized MS sheet hinges pin anodized of100mm size type B-21complete all as specified and as directed . |
| 86 | S&F, aluminum handles cast type anodized 125 mm size etc complete all as specified and as directed |
| 87 | S&F, aluminum anodized barrel tower bolts of extruded section 150 mm long etc complete all as specified and as directed |
| 88 | S&F in repair aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) 300mm long etc complete all as specified and as directed |
| 89 | S&Fin repair aluminum adjustable automatic spring door closer (silver colour) with allen key and screwsweight minium 200 gm etc complete and as directed. |
| 90 | Demolition of Brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar incl all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles etc complete all as specified and as directed. |
| 91 | M&L Brick work with sub class B bricks straight or curved on plan exe 6 m mean radius built in cement mortar 1:4 complete all as specified and as directed |
| 92 | Dismantling of timber scantling 40 sqcm and over for framed work and over in section, in any position complete all as specified and as directed . |
| 93 | Dismantling Asbestos cement ,galvalume fiber sheet ( Plan corrugated,semicorrugated, etc.) sheets in roof coverings all as specified and directed |
| 94 | M&L for Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified |
| 95 | M&L forPre-painted Galvatume aluminium zinc coating GI based plain steel sheet 0.50 mm thickof any colour havingtensile strength of 550 Mpa as in ridgefixed with shelf tapping screws as specified |
| 96 | M&L preparation of new or previously untreated steel surface of any description, over 10 cm width or girth, not other wise described and applying two coat of synthetic enamel paintof different tint over a coat of red oxide paint complet as specified and directed to Engr-in- Charge |
| 97 | S & F MS steel work in tubular trusses and tubular posts, purlin including special shaped washersetc., complete using ERW or induction butt welded tubesconforming to I.S.I 1161-1998 Grade St-240 with one shop coat of zinc chromate primer paint Complete all as specified and directed. |
| 98 | M&L chequered tiles (Cement) 30cm X 30cm x 25mm set and jointed and pointedin neat cement slurry infloor with grey cement and pigment over & including 20mm thick screed bed in CM (1:6) Complete all as specified and directed. |
| 99 | Dismantling ceiling boards (fiber,PVC,pulp,insulation etc) or wall board complete all as specified and as directed |
| 100 | S&F false ceiling with 7-9 mm thick acoustic board tiles laminated with white colour on face side & metalized polyster film (Aluminium foil) on the back side with all four edges sealed with PVC filmof size 600 x 600 mm (595 X 595 mm) fixed with clips & screws including silver GI/aluminum snap grid frame work for false ceiling of Tee/Angle of weight not less than 300 gm per RM with slot for fixing including necessary suspender of flat iron or 4 mm dia bars of required length fixed in purlin of roof not exceeding 1.20 m both ways including all accessories required for suspending ceiling work and gypsum board complete all as specified and as directed by the Engineer-in-Charge. |
| 101 | S&Ffalse ceiling with 4 mm thick gypsum board tiles laminated with white PVC film on face side & metalized polyster film (Aluminium foil) on the back side with all four edges sealed with PVC filmof size 600 x 600 mm (595 X 595 mm) fixed with clips & screws including anodised aluminium snap grid frame work for false ceiling of Tee/Angle of weight not less than 300 gm per RM with slot for fixing including necessary suspender of flat iron or 4 mm dia bars of required length fixed in purlin of roof not exceeding 1.20 m both ways including all accessories required for suspending ceiling work and gypsum board complete all as specified and as directed by the Engineer-in-Charge. |
| 102 | S & F in repair of 18mm thick UV coating, MDF board exterior grade, Both side laminated with any colour anti fungal,moisture resistence,anti borer, as per IS 14587 for kitchen/Cupboards shelfs fixing with 1st class hard wood lipping/beading etc. complete all as specified and directed by Engg-in-charge. NOTE:- Sample as approved by Engr-in-charge. |
| 103 | Supply & Fixing125 mm dia oval shape brass handle fancy type bright finish complete all as specified & directed. |
| 104 | Supply & Fixing wardrobe two track sliding channel and track roller for sliding shutter fixing in top and bottom of any size incliding all neccessry fittings complete all as specified and directed by Engg-in-charge. NOTE:- Sample as approved by Engr-in-charge |
| 105 | M&L, Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors all as specified and directed |
| 106 | S &F auto closing hinges 35 mm o crank ( KH-001) Or 8 crank ( KH-002) openable at 110 degree for kitchen cabinet shutterand fixed etc complete all as specified and direcetd. |
| 107 | Tacking down of shutters any description exc 1 sqm and n exc 2 sqm each and Refixing of same opening shutters including cutting and repairing for with keep it level with the existing floor complete all as specified and directed. |
| 108 | S&F MS chromium plated peg set of five fixing with wall complete all as specified and directed |
| 109 | M&L one coat synthetic enamel paint on old wooden surface incl prepartion of old surfaceof any description not otherwise described over 10 cm width or girth etc complete all as specified and as directed |
| 110 | S&F of 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, with decorative face veneers on both faces with lipping to match complete all as specified and directed. |
| 111 | Excavation in post holes (or similar holes) each n. exc 0.5 cum getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n. exc 50m and making good surface in soft/loose soil complete all as specified and directed. |
| 112 | M&L PCC 1:3:6Type D-2 (using 40mm gradedstone off) as in foundation, filling and mass concrete complete all as specified and directed. |
| 113 | S&F in repair 3 mm thick sheet glass, Ordinary quality and glazing with wooden beads in square n. exc 0.5 Sqm in each pane or glazing with oil glass putty including hacking out old broken glass from wooden or steel frame surround complete all as specified and as directed etc complete all as specified and as directed. |
