|
| 1 | Packing gasket | PTFE gasket roll small size |
| 2 | Washer clutch keys jib cotter and circlip | Minimum 25 mm size,carbon 1/2inch ,3/4 inch and 1 inch |
| 3 | Hollow punch | Straight Shank Hollow Punch Sets5-12mm |
| 4 | Bearing different types | each type of diameter 25mm (min.) |
| 5 | Lifting sling | 8mmNominalDia.Singleleg sling |
| 6 | Bearing extractor | Universalgearpuller2or3 jaws adjustable |
| 7 | Pulley extractor | Universalgearpuller2or3 jaws adjustable |
| 8 | Trammel | 300mm |
| 9 | Pocker | standerd |
| 10 | Prickpunch | 100mm |
| 11 | Mallet | Dia.100mmX 150mm |
| 12 | Aviation Snips straight Cut | 300mm |
| 13 | Flat headed hammers with handle | standerd |
| 14 | Planishing hammer | standerd |
| 15 | Snip bent Left Cut | 250mm |
| 16 | Stake hatchet with Leg | 300X200X20mm |
| 17 | Stake grooving. | 100 X100X300mm |
| 18 | Gauge snap Go and Not Go | 25to 50mm by 5mm,Set of 6 pieces |
| 19 | Gauge telescopic set. | 8-150 mm |
| 20 | Dial test indicator on stand | 0.01mmleastcount |
| 21 | Sine bar | 125mm |
| 22 | Dial Vernier caliper Universaltype | 0-300mm,LC0.05mm |
| 23 | Depth micrometer .0-25mm | Accuracy 0.01 mm with standard set of extension rods upto200mm |
| 24 | Comparators Gauge-Dial Indication with Stand and Bracket. | LC0.01mm |
| 25 | Engineers try square knife-edge | 150 mmBlade |
| 26 | Surface roughness comparison plates | N1- N12Grade |
| 27 | Vernier Bevel protector | Range360deg LC- 5min(150mmblade) |
| 28 | Carbide Wear Block | 1mm-2mm |
| 29 | Lathe tools H.S.S.tipped set | standerd |
| 30 | Lathe tools bit | 6mmx75mmHSS/Carbide |
| 31 | Lathe tools bit | 8mmx75mmHSS/Carbide |
| 32 | Lathe tools bit | 10mmx75mm HSS/Carbide |
| 33 | Armstrong type tool bit holder | Righthand |
| 34 | Armstrong type tool bit holder | Lefthand |
| 35 | Armstrong type tool bit holder | Straight |
| 36 | Stilson wrenches | 250mm |
| 37 | Pipe cutter wheel type. | 6mmto25mm |
| 38 | Pipe bender machine spool type with stand manually operated. | up to 25mm cold bending |
| 39 | Adjustable pipe chain tonge to take pipes | upto300 mm |
| 40 | Adjustable spanner | 380mmlong |
| 41 | Dual DC regulated power supply | 30-0-30 V, 2 Amps |
| 42 | Battery Charger | 0 - 6 - 9 - 12 - 24 - 48 V, 30 Amp |
| 43 | Analog multimeter | standerd |
| 44 | Clamp meter | 0 - 10 A |
| 45 | Autotransformer | 15 Amps |
| 46 | Milli Ammeter AC | 0 to 200 mA |
| 47 | Milli Ammeter DC | 0 to 500 mA |
| 48 | Digital IC Tester | standerd |
| 49 | Rheostats various values and ratings | standerd |
| 50 | Multimeter | Digital 0 to 1000 M Ohms, 2V to 700 V,100 micro A to 10A DC and AC |
| 51 | Megger | Analog - 500 V |
| 52 | Megger | 1000v |
| 53 | Hydrometer | standerd |
| 54 | Solar Insulation meter | standerd |
| 55 | Tong Tester - Clamp Meter | 0 - 100 A (Digital Type) |
| 56 | Soldering Iron | 25 Watt 230 volts |
| 57 | Soldering Iron | 65 Watt 230Volt |
| 58 | Soldering Iron | 120 Watt, 230Volt |
| 59 | Temperature controlled Soldering Iron | 50 Watt, 230 Volt |
| 60 | Thermometer Digital | 0 degree celcius to 150 degree celcius |
| 61 | Magnetic compass | standerd |
| 62 | Solar panels | 250 Wp |
| 63 | Solar charge controller with manual switch Day lighting | 12 V 10 A |
| 64 | Array junction box | for connecting 250W x 4 Nos. solar panel with DC fuse, DC MCB, and surge suppressor protection |
| 65 | Solar lantern | LED type |
| 66 | Clinometer | for Angle measurement |
| 67 | Spirit level | For floor level check |
| 68 | Anemometer | for wind speed measurement |
| 69 | DC table fan | 12 V |
| 70 | A.C. Voltmeter M.I | 0 to 500V AC |
| 71 | Volt meter | 0 - 30V |
| 72 | Volt meter | 0 - 100V |
| 73 | Ammeter MC | 0 - 1A |
| 74 | Ammeter MC | 0 - 5A |
| 75 | Ammeter MC centre zero | 0 - 20A |
| 76 | Ammeter MC centre zero | 0-50A |
| 77 | Rheostat | 0 -1 Ohm, 5 Amp |
| 78 | Rheostat | 0 -10 Ohm, 5 Amp |
| 79 | Rheostat | 0- 25 Ohm, 1 Amp |
| 80 | Rheostat | 0- 300 Ohm, 1 Amp |
| 81 | A.C. Energy Meter | Single Phase, 10 A, 240 V induction type |
| 82 | A.C. Energy Meter | Three Phase, 15 A, 440 V induction type |
| 83 | Kilo Wattmeter Analog | 0-1.5-3KW, pressure coil rating- 240v/440v, current rating-5A/10A Analog, portable type Housed in bakelite case |
| 84 | K.W. meter | 1KW |
| 85 | Phase Sequence Indicator | 3 Phase, 415 V |
| 86 | DC Pump | 24 V |
| 87 | Filler gauge | 0.05 mm - 1 mm |
| 88 | Dial thermometer remote control, armored capillary dial | 75mm - 50C to +50 C |
| 89 | Anemometer | Digital type |
| 90 | Digital thermometer | Graduated disc analogy type |
| 91 | Instrumentation screw driver set | 100mm |
| 92 | Digital weighing machine | 100 kg |
| 93 | Tachometer digital, multi range | 0 r m p to 3000 r m p. Portable small size in leather case |
| 94 | LED Lights 12v DC | 12v DC |
| 95 | Rechargeable battery , 12v 7 Ah | 12v 7 Ah |
| 96 | Magnifying glass | 100 mm |
| 97 | Magnifying glass | 75 mm |
| 98 | Inverter with Battery | 1 KVA with 12 V Battery Input- 12 volt DC, Output- 220 volt AC |
