Sales : +91-777 804 8217
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 20-02-2026 | Amendment in date | Date | 06-03-2026 |
| 2 | 16-02-2026 | Revised BOQ | BOQ | 27-02-2026 |
| 3 | 16-02-2026 | Date corrigendum | Date | 27-02-2026 |
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (unreinforced) any description and including of existing water proofing treatment from sunken portion of WC/Bath / Kitchen/ Passage including taking out plaster, lime/cement concrete, WC trap complete empty of existing sunk and removing rubbish out side of MoD land complete all as specified & as directed. |
| 2 | Demolition of cement concrete (unreinforced) in ground floor and pavings not exc 15 cm thick (below or above ground level) including floor tiles of any description complete all as specified & as directed. |
| 3 | Demolition of reinforced cement concrete in roof, floor (other than ground floors), beam, staircases, landing, chajjas and similar suspended work including removing rubbish out side of MoD land (reinforcement cut as required to facilitate demolition) not otherwise specifically provided for in this Schedule, complete all as specified & as directed. |
| 4 | Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed. |
| 5 | Taking down cement plaster or cement lime plaster, terrazo etc on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc, complete all as specified and as directed. |
| 6 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises, complete all as specified and as directed. |
| 7 | Dismantling of stone slabs and tiles of any description or any thickness in floors, dado etc, laid bedded and pointed in any mortar, complete all as specified & as directed. |
| 8 | Taking down chowkat or frame with shutters (including fittings & fixtures) area not exc 1.5 Sqm each (without taking off the shutters from the frame) of door/window including cutting holes for taking out hold fasts and making good the same including disturbed portion of jambs, cills, etc complete all as specified and as directed. |
| 9 | Taking down chowkat or frame with shutters (including fittings & fixtures) area exc 1.5 Sqm but not exc 4 Sqm each (without taking off the shutters from the frame) of door/window including cutting holes for taking out hold fasts and making good the same including disturbed portion of jambs, cills, etc complete all as specified and as directed. |
| 10 | Taking down chowkat or frame area exc 1.5 Sqm but not exc 4 Sqm each (without taking off the shutters from the frame) of door/window including cutting holes for taking out hold fasts and making good the same including disturbed portion of jambs, cills, etc complete all as specified and as directed. |
| 11 | M&L for anti-termite treatment to the soil under plinth protection at the rate of5 litres of emulsion per square metre of surface area, through approved applicator as per manufacturer\"s instructions complete all as specified & as directed. |
| 12 | M&L for anti termite treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors,through approved applicator as per manufacturer\"s instructions complete all as specified & as directed. |
| 13 | M&L for anti-termite treatment to the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall, through approved applicator as per manufacturer\"s instructions complete all as specified & as directed. |
| 14 | M&L for PCC 1:5:10 type E2 using 40mm graded crushed stone aggregate as in filling sunken part of slab complete all as specified and as directed. |
| 15 | M&L for PCC 1:3:6type C1 (using 20mm graded crushed stone aggregate) as in filling up chowkat/frame hollows and similar works complete all as specified and as directed. |
| 16 | M&L for precast RCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in landings, cover slabs (for man holes, drains etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including placing in position and set in CM (1:6) complete all as specified & as directed.Note :- Reinforcement shall be measured and paid for separately under respective item of this Schedule. |
| 17 | M&L for reinforced cement concrete (Nominal Mix) (1:2:4) type B1 using 20mm graded crushed stone aggregate as in slab supported on walls, beams, columns in floors, roofs, landings, cantilevers, bressummers, lintel over 1.5m span and the like complete all as specified & as directed.Note :- Reinforcement & formwork shall be measured and paid for separately. |
| 18 | Supply only integral liquid water proofing compound (ISI marked) complete all as specified & as directed. |
| 19 | M&L for precast cement concrete (1:2:4) type B-0 using 12.5mm graded stone aggregate set in cement and sand mortar (1:4) as in louvres and jallies, 35mm thick (measured solid) including all mouldings but excluding frame, complete all as specified and directed. |
| 20 | M&L for brick work with old size Fly Ash bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:6 complete all as specified and as directed. |
| 21 | M&L for brick work with old size Fly Ash bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed. |
| 22 | Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (Horizontal or sloping) for rough finished flat surfaces of concrete complete all as specified & as directed. |
| 23 | Formwork to edges of concrete flats,openings in concrete walls, floor and roofs, etc and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but not exc 20cm wide for rough finished surfaces of concrete complete all as specified & as directed. |
| 24 | M&L Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45x70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 Kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-charge complete all as directed. |
| 25 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45x85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 Kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-charge complete all as specified. |
| 26 | S&F Factory made 18mm thick WPC (Wood Polymer Composite) board in cupboard shutter/kitchen cabinet with decorative laminated on one side & other side balancing white, fixed with necessary stainless steel drilling screws/Anchoring bolt along with modular handles, design and colour as approved by GE including dismantling of boards any type, complete all as specified and directed. |
| 27 | S&F Factory made 18mm thick WPC (Wood Polymer Composite) board in cupboard shutter/kitchen cabinet with bothside balancing white fixed with necessary stainless steel drilling screws/Anchoring bolt along with modular handles, design and colour as approved by GE including dismantling of boards any type, complete all as specified and directed. |
| 28 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-in-Charge. |
| 29 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of 20 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and asdirected. |
| 30 | Supply and fixing factory made 35mm thick glazed and skeleton shutters made of second class hard wood, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in clause 8.24(a) of Section 8 in SSR Part-I, kiln seasoned and chemically pressure treated, fixed to chowkat, complete all as specified & as directed. |
| 31 | S&F factory made 30mm thick flush shutter, solid core construction, with block board core and plywood face panels, commercial type on both side complete all as specified and as directed. |
| 32 | Refixing of existing factory made 30mm thick flush shutter, solid core construction, with block board core and plywood face panels, commercial type on both side complete all as specified and as directed. |
| 33 | S&F continuous (piano) hinges, mild steel, bright finish or electro galvanized width of flaps 30mm (when open) fixed with CP steel screws complete all as specified and as directed. |
| 34 | S&F 100mm butt hinges, stainless steel, (ISI marked) complete all as specified and as directed. |
| 35 | S&F Stainless steel handles 100mm size for kitchen cabinet, cupboard shutters, pattern/design as approved by GE complete all as specified and directed. |
| 36 | S&F 200mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) fixed complete all as specified and as directed. |
| 37 | S&F 150mm aluminium handle, fabricated type, anodised, complete all as specified & as directed. |
| 38 | Supply & fixing hasp and staple of size 100mm aluminium anodized safety type with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed. |
| 39 | S&F 250 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed. |
| 40 | S&F magnetic catches for cabinet of size 50mm complete with striking plate & magnetic stud complete all as per approved smaple complete all as specified & as directed. |
| 41 | S&F 0 degree clip type self closing hinges for cabinets fixed with cadimum coated screws all as per sample complete all as specified and as directed. |
| 42 | S&F Ball bearing runners 450mm size Telescopic full extension load capacity 50 Kgs, of stainless steel grade SS-304 complete all as specified and as directed. |
| 43 | S&F in replacement of chromium plated stainless stell wire basket (storage basket) pull out type for large utensiles size 480x500x300mm of stainless steel Grade-304 with necessary fixing clips etc fixed complete all as specified and directed. |
| 44 | S&F in replacement of chromium plated stainless stell wire basket (Cup and saucer basket) pull out type for large utensiles size 480x500x150mm of stainless Steel Grade-304 with necessary fixing clips etc fixed complete all as specified and directed. |
| 45 | S&F in replacement of chromium plated stainless stell wire basket (plate basket) pull out type for large utensiles size 380x500x300mm of stainless steel grade-304 with necessary fixing clips etc fixed in repair complete all as specified and directed. |
| 46 | S&F in replacement of chromium plated stainless stell wire basket (Cutlery basket) pull out type for large utensiles size 380x500x150mm of stainless steel grade-304 with necessary fixing clips etc fixed complete all as specified and directed. |
| 47 | Supply and fixing Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed. |
| 48 | S&F in repairs stainless steel drapery rod of 25mm inner dia & 1.6mm wall thickness (in lengths as directed) with & including stainless steel sockets & decorative finial at both ends and pair of stainless steel brackets & stops fixed at both ends with PVC rawl plug & steel screws on walls/beam complete all as specified & as directed. |
| 49 | S&F mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, framed signed boards, walk ways, railings, framework of water tanks and similar work including welding conforming to Grade E-165 (Fe 290), complete all as specified & as directed. |
| 50 | M&L for mild steel TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified & as directed. |
| 51 | M&L for mild steel TMT bars 6 to 8 mm dia cut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified & as directed. |
| 52 | S&F factory made pressed steel frames of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, made out of mild steel sheet of 1.25 mm thickness, complete as specified & as directed. |
| 53 | S&F factory made pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, made out of mild steel sheet of 1.25 mm thickness, complete as specified & as directed. |
| 54 | S&F aluminium work powder coated of any colour as approved (thickness of powder coating not less than 50 micron) as in frame & shutters for doors, windows, ventilators, wall partitions, including joining cleats, glazing clips, snap beading, screws for fixing, etc., all aluminium sections as per relevant IS, complete all as specified & as directed. |
| 55 | S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 56 | S&F Pre-painted galvalume aluminium zinc coating corrugated steel sheet 0.50mm thick with coating AZ-150 gsm of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of old AC asbestos sheet complete all as specified & as directed.Note : Colour of sheet shall be as approved by the GE. |
| 57 | Demolition of roof treatment any thickness including PCC, Mud phuska PCC padding, plastering, APP membrane complete treatment and in any position and removing the demolished material out of MoD land complete all as specified and directed. |
| 58 | M&L for 40mm average thick PCC (1:2:4) type, B0 (using 12.5mm grd stone aggregate) as in floors/padding for levelling of roof surface and finishing the surface even and fair without using extra cement complete, all as specified anddirected. |
| 59 | M&L for APP based polymeric membrane not less than 3mm thick, weighing not less then 3 Kg/Sqm, reinforeced with polyster non-woven fabric (weighing not less than 150 gm/sqm). It shall be laid by torch application. Side overlaps shall be 75mm and the ends shall be 100mm and all overlaps and jointed shall also be sealed by torch application. For parapets, membrane shall be taken to a height of minimum 60cm and then inserted inside the parapet in a groove and same shall be flashed by membrane flashing. Complete APP membrane (in roof/parapet surfaces) shall be laid over and including a coat of cold applied bituminous primer confirming to IS:3384 @ 0.40 Kg per Sqm, complete all as specified & directed. |
| 60 | M&L for machine cut Kota stone slab flooring 20 to 25mm thick laid over & including screed bed or bedding layer of 20mm thick in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab with true & uniform joints including rubbing and mirror polishing complete all as specified & as directed. |
| 61 | M&L for machine cut Kota stone slab 18 to 20mm thick on vertical surfaces such as dado, skirting etc. laid over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab with true & uniform joints including rubbing and mirror polishing complete all as specified & as directed. |
| 62 | M&L for 18 to 20mm thick green marble (of any type) machine cut slab of approved shade (table rubbed and polished) with true & uniform joints as in steps, jambs, pillars, window cills, cooking platforms & like and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over & including 15mm thick screed bed (bedding layer) in CM 1:4 with cement slurry @ 3 Kg/Sqm complete all as specified & as directed.Note :The exposed edges of granite stone slab shall be made full round & polished to mirror finish and rate quoted shall deemed to include this provision. |
| 63 | Providing edging mounding to 18-20mm thick of stone slabs one edge, such as in steps, cooking platform, counters and other similar situations complete all as specified & as directed. |
| 64 | M&L for non skid ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:4 complete all as specified and as directed. |
| 65 | M&L for joint free ceramic tiles (coloured) 10mm thick, area of each tile not exceeding 0.36 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:4 and grouting the joints of flooring tiles having joints of 3mm width, using epoxy grout mix of 0.75 Kg of organic coated filler of desired shade (0.10) kg of hardener and 0.20 kg of resin per kg) including filling/grouting and finishing complete all as specified and as directed. |
| 66 | M&L for joint free ceramic tiles (coloured) 10mm thick, area of each tile not exceeding 0.36 sqm as in skirting, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over & including 10mm thick rendering in cement & sand mortar 1:4 and finishing complete all as specified and as directed. |
| 67 | M&L for glazed ceramic tiles (coloured) 7mm thick, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm (i.e 450mm x 300mm or as directed), on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 complete all as specified and as directed. |
| 68 | M&L for Cement concrete plain tiles 25cmx25cmx22mm thick, machine pressed, set jointed and pointed in neat cement slurry, laid over and including 15mm screed bedding layer in cement and sand mortar 1:4 and filling with the 2mm wide joints of tiles with cementitious grouting material complete all as specified & directed. |
| 69 | M&L for 75mm thick PCC (1:4:8) type D2 using 40mm graded crushed stone aggregate as in sub base complete all as specified and as directed. |
| 70 | Supply and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified & as directed. |
| 71 | M&L for Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement : 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified & as directed. |
| 72 | M&L for 50mm thick PCC 1:3:6 type C1 using 20mm graded crushed stone aggregate as in plinth protection surface finishedeven and smooth without using extra cement complete all as specified and directed. Note :- Plinth protection shall be of width as directed and shall belaid with an outward slope of 1:30 in alternative bays not exceeding 3 meter in length and grooves at corner. Joints of 6mm wide and 10mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3). |
| 73 | M&L for 10mm thick polymer modified plaster in cement and sand mortar 1:4 mixing the polymer in the ratio of 1:10 (1 part of polymer & 10 parts of cement) for sides and base of sunken floor portion including 2 coats of damp proof paint of approved quality complete all as specified & directed. |
| 74 | M&L for rendering 10mm thick in cement mortar 1:6 on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement complete all as specified. |
| 75 | M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick masonry or concrete surfaces of walls, mixed with integral liquid water proofing compound as per manufacturer’s instructions, finished even & smooth without using extra cement, complete all as specified and directed.Note : Supply only integral liquid water proofing compound shall be measured and paid for separately. |
| 76 | M&L for rendering 10mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified. |
| 77 | M&L for preparation of newly plastered / unplastered surfaces of walls & applying three coats of white wash complete all as specified. |
| 78 | M&L for complete removal of existing treatment (plastered or unplastered) of walls including brooming or steel wire brushing, scrapping down smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots and applying two coats of white wash complete all as specified & as directed. |
| 79 | M&L for preparation of newly plastered / unplastered surfaces of ceilings & applying three coats of white wash complete all as specified. |
| 80 | M&L for complete removal of existing treatment (plastered or unplastered) of ceiling including brooming or steel wire brushing, scrapping down smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots and applying three coats of white wash complete all as specified & as directed. |
| 81 | M&L for preparation of surface and applying two coats of 100% premium acrylic exterioremulsion paint having VOC less than 50 gm/litre & excellent protection against UV, Alkali & Fungal resistance, exterior paint of required shade (Company Depot tinted) with silicon additives @ 1.43 litre/10 Sqm over and including 2mmthick wall care putty and priming coatof exterior primer applied at 0.90 litre/10 Sqm over new surfaces upto tripple storey with fully utomatic airless spray machine of paint application having an electric motor of min 1 HP with a flow speed of min 1 litre per min having pressure 3300 PSI. Allow 6-8 hours to dry the surface of both coat of paint to achieve excellent application with 5 years perfomance warranty from manufacturers and instruction complete using limited man power including scaffolding, trestles, ladders, cradles and necessary safety measures for upto triple storey buildings, complete all as specified and directed.Note : (a) Complete work to be executed by authorised applicator from paint manufacturer. (b) Primer and emulsion application to be carried out through air less spray machine or by roller (only mechanical application allowed except in paint application on bands/chajja & building edges/ borders/projections where contrasting colour as specified and directed is to be applied. |
| 82 | M&L for preparation of old surface including complete removal and applying two coats of 100% premium acrylic exterior emulsion paint having VOC less than 50 gm/litre & excellent protection against UV, Alkali & Fungal resistance, exterior paint of required shade (Company Depot tinted) with silicon additives @ 1.43 litre/10 Sqm over 2mm thick wall care putty and including priming coatof exterior primer applied at 0.90 litre/10 Sqm over new surfaces upto tripple storey with fully utomatic airless spray machine of paint application having an electric motor of min 1 HP with a flow speed of min 1 litre per min having pressure 3300 PSI. Allow 6-8 hours to dry the surface of both coat of paint to achieve excellent application with 5 years perfomance warranty from manufacturers and instruction complete using limited man power including scaffolding, trestles, ladders, cradles and necessary safety measures for upto triple storey buildings, complete all as specified and directed.Note : (a) Complete work to be executed by authorised applicator from paint manufacturer. (b) Primer and emulsion application to be carried out through air less spray machine or by roller (only mechanical application allowed except in paint application on bands/chajja & building edges/ borders/projections where contrasting colour as specified and directed is to be applied. |
| 83 | M&L for applyingtwo coat of Oil bound distemper over a coat of primer & over a coat of 2mm thick wall care putty on newly plastered surface using airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 metre.The machine should should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper shold be able to spray in hard to reach areas and penetration of distemper on the surface complete all as specified and directed. |
| 84 | M&L for complete removal of existing surface and applyingtwo coat of Oil bound distemper over a coat of primer & over a coat of 2mm thick wall care putty on old plastered surface using airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 metre. The machine should should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper shold be able to spray in hard to reach areas and penetration of distemper on the surface complete all as specified and directed. |
| 85 | S&F 4.8mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, complete all as specified & as directed. |
| 86 | S&F 4mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, complete all as specified & as directed. |
| 87 | M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified & as directed. |
| 88 | M&L for preparation of old painted steel and iron surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint of approved tint all as specified & as directed. |
| 89 | M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamelpaint of approved tint over a coat of zinc chrome primer complete all as specified & as directed. |
| 90 | Supplying and laying of 15mm dia CPVC pipes SDR 11 & plain/brass CPVC SDR 11 fittings including all fittings and fixed complete to walls and ceiling or laid in floors, trenches including taking down steel water tubing and connections of15mm bore complete all as specified and as directed. |
| 91 | M&L for galvanized steel water tubing medium grade of 20mm bore with & including all fittings, fixed to walls and ceilings or laid in floors, including taking up or down steel water tubing and connections of 20mm bore complete all as specified and as directed. |
| 92 | S&F in replacement of GI tubes medium grade, laid on sunken floor as in spout pipe 32mm bore complete all as specified and directed. |
| 93 | Disconnecting & taking down the existing unserviceable water tank and Supply and fixing 750 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I and as directed.Note : (i) The water storage tanks shall be 2 layers, HDPE tanks moulded to seem-less perfection of rotational process. The tanks shall be manufactured only from FDA approved special grade of polyethylene and shall be certified fit for potable water.(ii) The tanks shall white coloured and ISI marked. Also refer paras 18.6 and 18.6A of MES Schedule Part-I.(iii) Payment for inlet, outlet and over flow pipes and ball valve shall be made separately. Howerver cost of providing necessary GI fittings such as nipples with check nuts for inlet and outlet pipes, GI plug with check nut for over flow pipe and 30cm long wash out pipe, GI 20mm nominal bore, medium grade and check nut for wash out pipes of size as per actual requirements as directed by Engineer-in-Charge shall be deemed to be included in the unit rates of this item. |
| 94 | S&F Ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe 25mm bore or brass ferrule and fixed complete all as specified and as directed. |
| 95 | S&F in repairs vitreous china squatting pan (Orissa pattern) water closet (white) of size 580x440mm with integral foot rests, ‘P’ trap setting the trap and pan in concrete and including 10 litre capacity PVC valveless syphonic action type low level flushing cistern having dual control flushing system and 32mm dia PVC flushing pipe complete including jointing to socket of flushing rim complete all as specified and as directed. |
| 96 | S&F in repairs vitreous china wash hand basin, white, flat back of size 550mm x 400mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified & as directed. |
| 97 | S&F sink with drainage board made of stainless steel 1mm thick for Kitchen with plugs, washers and wastes, including fixing with cast iron cantilever brackets, bedding in cement mortar on to brick wall, connecting union to pipe, overall minimum size 915mm x 460 mm with bowl size 410mm x 330mm x160 mm including 40mm dia waste pipe of polythelene of low or high density, 40mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0, complete all as specified and as directed including taking down old unserviceable sink with fittings. |
| 98 | S&F in repairs stainless steel Kitchen plate rack of overall minimum size 750mm x 600mm and 250mm deep, with partitions for small/large plates etc, made out of stainless steel sheet 24 Gauge, fixed with rawl plug and CP steel screws complete all as specified and as directed. |
| 99 | S&F in replacement of PVC connection 450mm long suitable for 15 mm bore GI pipe including PTMT nuts on both sides complete all as specified & as directed. |
| 100 | S&F in replacement of 15mm bore pillar tap, weight not less than 650 gm, cast copper alloy with capstan heads, chromium plated, fancy type, long body, screwed down high pressure, with or without lettered‘Hot’ or ‘Cold’ with long screwed shanks & fly nuts, screwed for iron pipes, complete all as specified & as directed. |
| 101 | S&F in replacement of 15mm bore bib tap, cast copper alloy, chromium plated, long body, fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified & as directed.Make : Jaquar, Cat Part No. KUP-CHR-35037/Cera Cat Part No. F-1003151/Kohler Cat Part No. K-16093 IN-4-CP. |
| 102 | S&F in replacement of 15mm bore fancy type Mixer, wall mounted, head and hand arrangement combination pattern, including telephone hand shower, flexible tube and work connecting legs and wall flanges, cast copper alloy, chromium plated, screwed down high pressure, with long screwed shanks & fly nuts, screwed for iron pipes, complete all as specified & as directed.Make : Jaquar, Cat Part No. LYR-38145/Cera Cat Part No. F-1003403/Kohler Cat Part No. K-98754 IN-4-CP. |
| 103 | S&F in replacement of 15mm bore stop valve/Angular cock, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified & as directed.Make : Jaquar, Cat Part No. KUP-CHR-350553PM/Cera Cat Part No. F-1003201/Kohler Cat Part No. K-80154 IN-4AV-CP. |
| 104 | S&F in repairs 20mm bore Gun metal gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, complete all as specified & directed. |
| 105 | S&F in repairs 600mm x 450mm looking mirror of selected quality glass not less than 5.5mm thick, mounted on 6mm thick AC building board or commercial plywood including aluminium framing and fixed to PVC rawl plugs with chromium plated brass screws and cup washers complete all as specified. |
| 106 | S&F in repairs brass chromium plated Overhead shower 300x300mm square shape with 600mm long arm including fixing to steel pipe of 15mm bore or union complete all as specified and as directed.Make : Jaquar, Cat Part No. OHS-CHR-1639/Cera Cat Part No. F-7010109SS/Kohler Cat Part No. K-73038 IN-CL-CP. |
| 107 | S&F in repairs tubular towel rail, brass chromium plated, 20mm dia, ‘D’ type, 60cm long between flanges, fixed to PVC rawl plugs with chromium plated brass screws, complete all as specified and as directed. |
| 108 | S&F in repairs Towel ring of stainless steel of standard size fixed with and including brass chromium plated fixed on wall with brass screws and wooden/plastic cleats complete all as specified & as directed. |
| 109 | S&F 32mm bore Low density polyethylene pipes (LDPE) of pressure rating 6 Kgf/cm2 and fittings, fixed to WHB, complete all as specified and directed. |
| 110 | S&F in repairs soap dish holder brass chromium plated fixed on wall with PVC rawl plug & cadmium plated brass screws complete all as specified & as directed.Make : Cat Part No AKP-CHR-35731P of Jaquar/Cat Part No. F-5012116CH of Cera/Cat Part No. K-25069IN-CP of Kohler. |
| 111 | S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with aluminium alloy brackets and guard rail 60cm long fixed on wall with PVC rawl plug & cadmium plated brass screws, complete all as specified and as directed. |
| 112 | S&F in repairs corner glass shelfwith stainless steel bracket fixed on wall with PVC rawl plug & cadmium plated brass screws.Make : Cat Part No CAN-CHR-1173 of Jaquar/Cat Part No. F-5005102 of Cera/Cat Part No. T-6010A1 of Parryware. |
| 113 | S&F in repairs cast copper alloy chromium plated towel rack 600mm long with lower hangers complete all as specified and as directed.Make : Cat Part No CPA-CHR-1181FH of Jaquar/Cat Part No. F-5012101CH of Cera/Cat Part No. K-25066IN-CP of Kohler. |
| 114 | Supply and fixing in replacement of 100mm bore cast iron, spun pipe, soil, waste & vent pipe (ISI marked), in any length with or without ears fixed with cement joints, laid in trenches or floors, complete all as specified and as directed. |
| 115 | Supply and fixing in replacement of 75mm bore cast iron, spun pipe, soil, waste & vent pipe (ISI marked), in any length with or without ears fixed with cement joints, laid in trenches or floors, complete all as specified and as directed. |
| 116 | Supply and fixing in replacement of 100mm bore cast iron, spun pipe, soil, waste & vent pipe (ISI marked), in any length with or without ears fixed with cement joints, fixed to walls, complete all as specified and as directed. |
| 117 | Supply and fixing in replacement of 75mm bore cast iron, spun pipe, soil, waste & vent pipe (ISI marked), in any length with or without ears fixed with cement joints, fixed to walls, complete all as specified and as directed. |
| 118 | S&F stack clamp made out of MS flat 50mm x 5mm and 16 mm dia round iron stays, including bolts & nuts, securing ends of stays to walls or roof for 75/110mm bore pipe including two coats of synthetic enamel paint over a coat of red oxide primer including preparation of surfaces complete allas specified & as directed. |
| 119 | S&F 100mm bore cast iron bends and Tee (any radius), diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified & as directed. |
| 120 | S&F 100mm bore cast iron bends and Tee (any radius), diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified & as directed. |
| 121 | S&F 75mm bore cast iron nahani trap with grating including jointing to waste pipe, fixed in cement concrete type B1 (1:2:4), complete all as specified & as directed. |
| 122 | S&F in replacement of 110mm bore PVC (SWR type A) pipes single socketed in any length with rubber ring joints / solvent cement joints fixed to walls complete all as specified & as directed. |
| 123 | S&F 40mm waste fittings, brass, chromium plated for sinks with long screwed shanks and fly nuts, flange end bedded in red lead coment and other end fixed complete all as specified and as directed. |
| 124 | M&L for salt glazed stone ware gully trap square or round mouthed type \"P\" of size 150 x 150 mm with CI grating, setting & jointing with cement with grouting surrounding gully trap with PCC 1:3:6, type C1block 30x30x45cm together with necessary form work, excavation & earth work in soft/loose soil, complete all as specified and as directed. |
| 125 | S&F hard drawn steel wire fabric, weight not exc 4 Kg per sqm, cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia, supplied and fixed in reinforcement, complete all as specified & as directed. |
| 126 | Taking down carefully existing unserviceable/perished surface conduit/concealed conduit/ batten/casing caping aluminium/copper point wiring any type for light, fan, bell, socket, power point etc complete including all fixtures and fittings such as batten/conduit/casing caping, switches, sockets, ceiling rose, pendent holder, lamp holders, bracket holders, light fittings, top sheet covers, fan regulators, wooden boxes, MS sunken boxes, etc and making good the disturbed surfaces of wall, floors, ceiling, etc to match with the adjoining surfaces, complete all as specified and as directed. |
| 127 | M&L for Modular point wiring for one light/fan/bell/buzzer point controlled by one, one way switch with 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade (ISI marked) including 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade (ISI marked) as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including non-metallic rigid PVC concealed conduit (medium duty, ISI marked, not less than 20mm dia) with all fittings such as tee, bends, etcall as per IS, terminated in & modular metal flush boxes of requisite module concealed in wall for mounting fittings like modular switches, sockets, regulators etc with and including modular cover plates with frame of requisite module, complete all as specified and as directed.Notes : Cost of cutting/leaving forming chases for conduits, sinking for modular metal flush boxes and making good in CM 1:4 shall deemed to be included in quoted rate of this item. |
| 128 | All as per serial item No. 127.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on same board with other switches complete all as specified and directed. |
| 129 | All as per serial item No. 127.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on independent board complete all as specified and directed. |
| 130 | All as per serial item No. 127.00 here-in-before but for one light point controlled by two, two way switches complete all as specified and directed. |
| 131 | All as per serial item No. 127.00 here-in-before but for one 3 pin 15/16 Amps socket outlet controlled by one 15/16 Amps switch on independent board with 2.5 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade (ISI marked) including 2.5 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade (ISI marked) as continuous earth wire in green colour complete all as specified and directed. |
| 132 | S&F modular bell push, flush type, 5 Amp, 230 Volts, ISI marked, complete all as specified and as directed. |
| 133 | S&F Modular switch 1 way 6 Amp, 1 module, complete all as specified and as directed. |
| 134 | S&F Modular switch 2 way 6 Amp, 1 module, complete all as specified and as directed. |
| 135 | S&F Modular switch, 1 way 16 Amp, 1 module, complete all as specified and as directed. |
| 136 | S&F Modular Socket, 6 Amp - 2 in 1, 5 pin combined 2 module, complete all as specified and as directed. |
| 137 | S&F Modular Socket 6 Amp/16 Amp - 2-in-1, 3 and 5 pin combined 2 module, complete all as specified and as directed. |
| 138 | S&F Modular cover plate 1 modules complete all as specified and directed. |
| 139 | S&F Modular cover plate 2 modules complete all as specified and directed. |
| 140 | S&F Modular cover plate 3 modules complete all as specified and directed. |
| 141 | S&F Modular cover plate 8 modules complete all as specified and directed. |
| 142 | S&F Metal flush box 1/2 module complete all as specified and directed. |
| 143 | S&F Metal flush box 3 module complete all as specified and directed. |
| 144 | S&F Metal flush box 8 module complete all as specified and directed. |
| 145 | S&F Modular Fan step regulator, 120 Watt - 2 module, complete all as specified and as directed. |
| 146 | S&F ceiling rose, PVC/Polycarbonate insulated body, 65mmx50mm with three terminals, ISI marked, complete all as specified and as directed. |
| 147 | S&F lamp holder, PVC/Polycarbonate insulated body with back plate suitable for conduit/casing caping fittings, ISI marked, complete all as specified and as directed. |
| 148 | Supply & fixing in replacement of indoor decorative ultra slim surface /Wall mounted LEDbatten tube light complete fitting 1x20 watt LED Tube fitting withpolycarbonate channel housing & integrated electronic driver,energy efficient, 140 Volt-270 Volt, co-related colour temperature (CCT) of 6500 K, >100 Lm/Watt complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed. |
| 149 | Supply and fixing in replacement of LED T-5 Intergrated Batten PC housing extruded 2\" light fittings 9 Wattcomplete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed by Enginee-in-Charge. |
| 150 | S&F in replacement of Decorative wall light fitting stainless steel rust free fixture with white glass diffuser with 7.5/ 9 Watt LED lamp complete all as specified and directed. |
| 151 | Supply and fixing LED retrofit lamp 9 Watt complete all as specified and as directed. |
| 152 | Supply and Fixing Light Emitting Diode (LED) based street/security light fitting, 30 Watt with & including LED lamp, housing made up of LM6 pressure die cast aluminium alloy with effective thermal management, sturdiness, monolithic construction, totally enclosed, dust and water proof, minimum system efficiency of more than 100 lumens per watt and a minimum system lumen output of not less than 2500 lumens, correlated colour temperature shall be minimum 5700 degree Kelvin, Colour Rendering Index (CRI) shall not be less than 70, fitting shall be designed for a system life of 50,000 hours @ 70% lumen maintenance, ingress protection of IP-65 (minimum), mechanical impact resistance rating of IK ≥ 07, operating voltage range 140 V to 270 V, AC, frequency 50-60Hz, potted type for humming free operation, driver shall withstand upto 400 V for 08 hours, surge protection not less than 10 KV, Power factor > 0.95, Total Harmonic Distortion (THD) shall be less than 15%, double phase protection, no load, open circuit and short circuit protection, suitable for ambient temperature from (-)10°C to 50°C and humidity level 10% to 90% RH, cool white colour and lamp starting time shall not be more than 10 second, PMMA/ polycarbonate/toughened glass heat resistant cover, prewired and connecting up to street light feeder/junction box with & including 2.5 Sqmm 3 core PVC insulated, weather proof, multistranded copper conductor cable of 1100 Volt grade (ISI marked), complete all as specified and as directed. |
| 153 | NOTES FOR LED LIGHT FITTINGS :(i) All LED light/luminare shall meet the provision laid down in IS - 16101, 16102 Part-I/II, 16103 Part-I, 16104, 16105, 16106, 16108/2012 and 15885 Part -II / Section 13.(ii) Contractor shall submit test report of LED street light fitting from Government accredited test laboratory for LM-79 and LM-80.(iii) Contractor has to furnish a replacement warranty of 05 years for LED light fittings complete including lamps from the date of completion of contract. The product will be replaced on site free of cost in the following case :-(a) Manufacturing defects.(b) Failure due to mechanical and electrical impact.(c) Drop in lumen (or lux at 1 m) below 90% of claimed values of lumen (or lux at 1 m) of the LED /Luminaries. |
| 154 | M&L for building security light bracket made out of 40mm dia light grade GI pipe of 1.20m length bent to required shape suitable for fixing street light fitting on Steel tubular pole/wall including two Nos clamps made out 40mmx6mm flat with suitable nuts and bolts including two coats of aluminium paint over a coating of red oxide primer complete all as directed. |
| 155 | S&F sheet metal enclosure for distribution boards flushed and surface mounting, double door type (IP-43 IK 09 with metal door), suitable for fixing MCBs, 240 Volts with 200 Amps rated bus bar, with neutral bar, earth bar and cables ties for cable management fully insulated bus bar, DB fitted with bus bar neutral links blank plates, SPN, 8 way, suitable for MCBs, fitted with and accessories, including taking down old existing unserviceable DB with fixtures of any type complete all as specified and as directed.Note : Cost of cutting/leaving forming chases for sinking for DB and making good in CM 1:4 shall deemed to be included in quoted rate of this item. |
| 156 | S&F in replacement of MCB, 6 to 32 Amps, Single Pole (SP), 240 Volts, rupturing capacity not less than 10 kA, ‘C’ Curve,with over load and short circuit protection, complete all as specified and as directed. |
| 157 | S&F in replacement of MCB, 40-63 Amps, Double Pole (DP), 240 Volts, rupturing capacity not less than 10 kA, ‘C’ Curve,with over load and short circuit protection, complete all as specified and as directed. |
| 158 | Taking down the ceiling/exhuast fan of any sweep carefully from its installed position, dismantling complete with down rod, cleaning of all dust, applying grease for bearings, reassembling the fan and blades, keeping a side safely and hanging / refixing in position after spray ainting and connecting up including provision of 3 core twisted flexible copper conductor cable of 0.75 sqmm from ceiling rose to connector of fan and testing on completion complete all as directed. |
| 159 | M&L for earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level and connected to and including galvanized iron earth wire 4 mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No 3 of SSR Part-I and connection to main switch board/Test point/panel/equipment and testing on completion including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exc 50 metre,charcoal and salt in alternate layer 15 cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering and 15 mm bore 7.50 metre long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25 mmx3mm, bolts, nuts and washers,PCCchamber (1:3:6) type C1, 40 mm thick RCC pit cover, etc complete all as specified & as directed.Note : PCC chamber shall be constructed at least 1.5 mtr away from the earth electrode and pipe for watering shall be provided in slanting manner. |
| 160 | M&L for sub main wiring with two runs of 6 sqmm (nominal area) size main cable & one run of 6 sqmm size earth continuity conductor, single core, PVC insulated, unsheathed, FRLS with multi-stranded copper conductor, 1100 Volts grade, ISI markedcables, drawn through & including suitable size of heavy duty non-metallic rigid PVC concealed conduit ISI marked not less than 25mm dia & conduit fittings/accessories, fixed concealed in wall/ceiling including dismantling & taking down old unserviceable sub main wiring complete all as specified and directed.Notes :-(i) 02 runs of 6 sqmm size main cable, 01 run of 6 sqmm size earth continuity conductor cable & conduit with accessories shall be measured as one run length for payment purpose. (ii) Cost of cutting/leaving forming chases for conduits and making good in CM 1:4 shall deemed to be included in quoted rate of this item. |
| 161 | Supply, laying, jointing and testing LT XLPE insulated screened,bedded, galvanised steel strip or wire armoured heavy duty electric cable with aluminium stranded conductor 1100 Volt grade cross sectional area 70 sqmm 3.5 core laid in trenches/ducts, through pipe, under floors or roads/ along poles etc complete all as specified and directed.Notes :- (i) Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately.(ii) Road cutting/floor cutting /cutting holes etc in walls required for laying/fixing of cable etc shall be made good as per existing. Nothing extra shall be admissible on this account. Quoted rates shall be inclusive of the above provisions. |
| 162 | Taking out the electric geyser of capacity 25 Litres carefully from its installed position by disconneting inlet and outlet water pipes, dismantling the unit and replacing the defective Parts and painting with one coat of synthetic enamel paint and witing MES No. and safely keeping a side & re-fixing the same in its original position after completion of civil work and reconnecting the inlet/outlet water pipes and testing on complete all as specified and directed.NOTE:- The spare parts required shall be measured and paid separately under relevant items. |
| 163 | Supply only the following items suitable for electric geyser of capacity 25 Liters:- |
| 164 | Heating element 1.5 / 2 KW ISI marked including rubber Gasket as per existing type. |
| 165 | Thermostat suitable for 25 Litres Geyser (as per the existing type). |
| 166 | Hot water / coldwater pipe 600mm long as per existing type. |
| 167 | Supply, installation, commissioning and testing of LT Indoor type floor mounted panel board (factory made of approved CPRI) made out of CRCA sheet 3.15mm thickness for outer sheet and 2mm thicness for inner sheet dust proof, powder coated from both side, individual door, factory locking system with two side ventilation suitable for working on 415 Volt, 50 Hz, AC supply including bus bar chamber and water proof duly supported on 40x40x6mm angle iron frame, opening arrangement from front & rear both duly fitted with compression cable glands for entry & exit of cables having minimun clearance of 450mm above floor level complete including taking down old panel comprising of the following :-(a) Panel mounted Multi-function for voltage, current, frequency, power factor and power Type EM-VIFP -01 set(b) Aluminium bus bar - 03 Nos. For Phase of capacity 200 Amp and 1 Nos 200 Amps for neutral,duly taped in colour coded FRP sleeves.(c) LED Indicating lamps Red, Yellow and blue complete with lamp holders, 220 volts AC.- 01 Set of 3(d) Panel wiring with 2.5 Sqmm PVC Sheathed, PVC insulated FR-HR stranded copper conductor cable through MCB DP 10 Amp mounted on DIN rail.(e) MCCB 4 Pole 160 Amp, (Ics=100%Icu) 415 Volt , 26 KA - 01 No (Incommer)(f)MCB 2 Pole DP 40-63 Amps, 220 Volt , 10 KA - 13 Nos (Outgoing)(g) Provision for mounting of 12-13 Pre-paid meter |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
