|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. |
| 2 | All kinds of soil. |
| 3 | Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : |
| 4 | All kinds of soil. |
| 5 | Pipes, cables etc, not exceeding 80 mm dia. |
| 6 | Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia |
| 7 | Repairs to cement concrete road in patches by Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering and finishing the surface to match with existing cement concrete road etc. complete as per the direction of Engineer in charge. |
| 8 | 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 9 | 1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 10 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 3.5 in foundation and plinth in: |
| 11 | Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 12 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 3.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : |
| 13 | Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 14 | Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinalpartitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finishedsmooth. |
| 15 | White Marble Stone |
| 16 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). |
| 17 | Second class teak wood |
| 18 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: |
| 19 | 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 20 | Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete : |
| 21 | 125x64x1.90 mm |
| 22 | 100X58X1.90 mm |
| 23 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessaryaccessories and screws etc. complete. |
| 24 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : |
| 25 | 300x16 mm |
| 26 | 250x16 mm |
| 27 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 28 | 250x10 mm |
| 29 | 100x10 mm |
| 30 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 31 | 100 mm |
| 32 | 75 mm |
| 33 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. |
| 34 | Twin rubber stopper |
| 35 | Providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles of approved quality for aluminium door, with necessary screws etc complete as per direction of Engineer-in-charge. |
| 36 | Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineer-in-Charge. |
| 37 | Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC ‘C’ channel of size 30mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the ‘C’ Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer’s specification & drawing. |
| 38 | 30 mm thick plain PVC door shutters |
| 39 | Providing and fixing aluminium latches of approved quality and transparent or dyed to required colour or shade, with nuts and screws etc. complete : |
| 40 | 250x19x9 mm |
| 41 | Providing and fixing M.S. steel window casementfastener with necessary screws or bolts etc. completeas per the direction of Engineer in charge. |
| 42 | 100 mm |
| 43 | Providing and fixing M.S. window casement stays (straight peg type) with necessary screws etc. completeas per the direction of Engineer in charge. |
| 44 | 300 mm weighing not less than 200 grams |
| 45 | Repairs to M.S. Rolling shutter of any size by necessary cleaning, oiling and greasing so as to make smooth functioning of shutter. The item includes labour charges for replacement of rusted interlocking M.S. lath section of required size and thickness and replacement of necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength wherever required etc. complete as per the direction of Engineer in charge. The cost of labour charges shall be paid under part a) and the cost of materials i.e cost of interlocking M.S. lath section and 27.5cm long wire spring shall be paid under part b). |
| 46 | Labour chrges for repairing including replacement as mentioned above in Item. |
| 47 | Materials |
| 48 | 80x1.25 mm interlocking M.S. laths |
| 49 | 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength |
| 50 | Servicing & oilingof steel windows including removingmortar, plaster etc from frames, chieseling plaster of jams & soffitsand making the shutters smooth operational etc. all complete as required and directed by Engineer-in-charge. |
| 51 | Repairing of MS steel windows/windows grill with or without taking out fixed/openable shutter/grill and getting repair at any floor levelby welding of grill/ M. S. butt hinges /holdfast/straightening/ cutting of members and other required arrangment for proper functioning of window etc and fixing in position as directed by engineer-in-charge.( The item includes cost ofall opearations and MS hingesof any type, labours and tools and plant etc. but excluding cost of scaffolding and glass panes which shall be paid for seperately in relevant item.) |
| 52 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc. complete. |
| 53 | Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. |
| 54 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. |
| 55 | 110 mm diameter |
| 56 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. The item excludes cost of scaffolding which shall beincluded in relevant item of scaffolding for maintenance work. |
| 57 | Coupler |
| 58 | 110 mm diameter |
| 59 | Single tee with door |
| 60 | 110 mm diameter |
| 61 | Single tee without door |
| 62 | 110 mm diameter |
| 63 | Bend 87.5° |
| 64 | 110 mm diameter |
| 65 | Shoe (Plain) |
| 66 | 110 mm diameter |
| 67 | Providing and fixing M.S. clamps made of 20x5 mm flat of approved design, size and shape to unplasticised - PVC rain water pipes fixed with M.S. justi khila of required length including applying steel primer and painting with Two coats of synthetic enemel paint of approved quality etc. complete as per the direction of Engineer incharge. |
| 68 | 110 mm diameter |
| 69 | Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. meters and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50metres lead. |
| 70 | With cement mortar 1:4 (1 cement : 4 fine sand) |
| 71 | Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: |
| 72 | Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm) |
| 73 | Renewal of old putty of glass panes (length) |
| 74 | Providing & fixing White vitreous china water closet squatting pan (Indian type) along with \"S\" or \"P\" trap including dismantling of old WC seat and \"S\" or \"P\" trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of Engineer-in charge. |
| 75 | Orissa pattern W.C Pan of size 580x440 mm |
| 76 | Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in-Charge. |
| 77 | Dismantling 15 to 40 mm dia G.I. pipe with fittings including stacking of dismantled pipes (within 50 metres lead) as per direction of Engineer in-Charge. |
| 78 | Internal Work- Exposed on wall |
| 79 | Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge. |
| 80 | Fixing of loose Aldrop, Stopper, Latch, handle etc. fixed to door/window shutter with necessary screws, rawl plugs, Bolts & Nuts etc. as required, all complete as per the direction of the Engineer-in-charge. |
| 81 | Deduct for providing 3mm thick Bajari glass panes instead of ordinary float glass panes weighing 4 mm thick in steel glazed doors, windows and clerestory windows shutters and ventilations. |
| 82 | Demolishing lime concrete/ Brick bat cement concrete manually/ by mechanical means and disposal of material within 50 metres lead as per direction of Engineer in-charge |
| 83 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. |
| 84 | Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 85 | Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) |
| 86 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. |
| 87 | In cement mortar |
| 88 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : |
| 89 | Of area 3 sq. metres and below |
| 90 | Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead : |
| 91 | Of area 3 sq. metres and below |
| 92 | Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead. |
| 93 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. |
| 94 | For thickness of tiles 10 mm to 25 mm |
| 95 | Dismantling C.I. or asbestos or PVC rain water pipe/drainage pipes with fittings and clamps including stacking the material within 50 metres lead : |
| 96 | 75 to 80 mm dia pipe |
| 97 | 100 mm dia pipe |
| 98 | Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge : |
| 99 | 15 mm to 40 mm nominal bore |
| 100 | Taking out C.I. cover with frame from R.C.C. top slab of manholes of various sizes including demolishing of R.C.C. work manually/ by mechanical means and stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead as per direction of Engineer-in-charge. |
| 101 | Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead. |
| 102 | Disposal of building rubbish/ malba/ similar unserviceable dismantled or waste materials by mechanical means including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all loads including all lifts involved. |
| 103 | Deductionfor taking over of unserviceable materials obtained from dismantling/ demolishing as is where is basis. Note : Materials shall be taken over by the contractor at his own cost and will allow to deduct at the quoted rate from the bill of payment. |
| 104 | C.I./S.C.I. pipe & fittings, C.I. cover etc. |
| 105 | StructuralSteelmembers like Tee, angle, flats, square bars, Channels, Rolling shutter, etc. |
| 106 | Brass/ CP brass pillar cock, stop cock, Bib cock, Gate valve, Flush cock, etc. |
| 107 | 15 mm dia. G.I. Pipe & fittings |
| 108 | 20 mm dia. G.I. Pipe & fittings |
| 109 | 25 mm dia. G.I. Pipe & fittings |
| 110 | 32 mm dia. G.I. Pipe & fittings |
| 111 | 40 mm dia. G.I. Pipe & fittings |
| 112 | PVC Flushing cistern - 10 Litres capacity |
| 113 | PTMT/PVC Bib cock, stop cock, Pillar cock, etc. |
| 114 | 20 to 25mm thick kota stone slab |
| 115 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. |
| 116 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. |
| 117 | 10 litre capacity - White |
| 118 | Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete : |
| 119 | White solid plastic seat with lid |
| 120 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively. |
| 121 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. |
| 122 | Flexible pipe |
| 123 | 32 mm dia |
| 124 | 40 mm dia |
| 125 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 126 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : |
| 127 | Rectangular shape 453x357 mm |
| 128 | Providing and fixing white vitreous china wash basin (Cera or Equivalent) including making all connections but excluding the cost of fittings : |
| 129 | Flat back wash basin of size 550x400 mm. |
| 130 | Providing and fixing PTMT Waste Coupling for wash basin and sink of \"Prayag\" or equivalent make as per direction of Engineer in Charge. |
| 131 | Waste coupling 31 mm dia of 79 mm length and 62 mm breadth weighing not less than 45 gms. |
| 132 | Providing and fixing White Vitreous China Flat back wash basin (Cera or Equivalent) of size 550x400mm with C.I. brackets, 15 mm C.P. Brass pillar cock, 32 mm C.P. Brass waste coupling of standard pattern, including cutting and making good the walls wherever required etc. complete as per the direction of Engineer in charge. |
| 133 | Providing and fixing white vitreous china pedestal type (European type/ wash down type) water closet pan (Cera or Equivalent) etc. complete as per the direction of Engineer in charge. |
| 134 | Providing and fixing C.P. brass health Faucet with flexible tube upto 1 metre long with hook to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. |
| 135 | 15 mm nominal dia |
| 136 | Providing and fixing C.P. brass Coupling for wash basin and sink, of approved quality as per the direction of Engineer in charge. |
| 137 | 32mm dia. |
| 138 | 40mm dia. |
| 139 | Providing and fixing PVC Nahni trap of self cleansing design of approved make including cost of cutting and making good the walls and floorsetc. complete as per the direction of Engineer in charge. |
| 140 | 110 mm inlet and 75 mm outlet |
| 141 | Providing and fixing on wall face unplasticised Rigid PVC single socketed drain pipes conforming to IS : 13592 , Type-B of approved quality & manufacture including jointing etc. all complete as per thedirection of Engineer-in-charge. The item excludes cost of scaffolding which shall be inclusive in relevant item of scaffolding for maintenance work. |
| 142 | 110mm diameter |
| 143 | 75mm diameter |
| 144 | Providing and fixing on wall face unplasticised Rigid PVC moulded fittings/acessories for unplasticised Rigid PVC drain pipes conforming to IS : 13592 , Type-B of approved quality & manufacture including jointing etc. all complete as per thedirection of Engineer-in-charge. The item includes connecting with existing cast iron NT or P trap of WC with cement, Mseal etc. and plugging the hole with cement mortar etc. all complete |
| 145 | Tee with access door |
| 146 | 110x110x110mm |
| 147 | 75x75x75mm |
| 148 | Double Y with access door |
| 149 | 110x110x110x110mm |
| 150 | 75x75x75x75mm |
| 151 | Single Y with access door |
| 152 | 110x110x110mm |
| 153 | 75x75x75mm |
| 154 | Bend87.5° with access door |
| 155 | 110mm |
| 156 | 75mm |
| 157 | Bend 87.5° |
| 158 | 110mm |
| 159 | 75mm |
| 160 | Cowl |
| 161 | 110mm |
| 162 | 75mm |
| 163 | Coupler |
| 164 | 110mm |
| 165 | 75mm |
| 166 | Providing and fixing M.S. clamps made of 20x5 mm flat of approved design, size and shape to unplasticised - PVC drainage pipes fixed with M.S. justi khila of required length including applying steel primer and painting with Two coats of synthetic enemel paint of approved quality etc. complete as per the direction of Engineer incharge. |
| 167 | 110 mm dia. pipe |
| 168 | 75 mm dia. Pipe |
| 169 | Providing and fixing PVC pipes including all PVC fittings, including fixing the pipe with clamps at 1.0m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall |
| 170 | 40 mm nominal bore |
| 171 | Providing and fixing uplasticised PVC connection pipe with brass unions : |
| 172 | 45 cm length |
| 173 | 15 mm nominal bore |
| 174 | Proiving and fixing C.P. brass Bib cock of \"ESSCO\" or equivalent make including removing existing nonfunctional Bib cock all complete as per direction of Engineer in charge. |
| 175 | 15mm nominal bore |
| 176 | Proiving and fixing C.P. brass Stop cock/ angle cock of \"ESSCO\" or equivalent make including removing existing nonfunctional Stop cock/ angle cock all complete as per direction of Engineer in charge. |
| 177 | 15mm nominal bore |
| 178 | Proiving and fixing C.P. brass Pillar cock of \"ESSCO\" or equivalent make including removing existing nonfunctional Pillar cock all complete as per direction of Engineer in charge. |
| 179 | 15mm nominal bore |
| 180 | Providing and fixing S.S. extension nipple of approved make and quality as per direction of Engineer-in-charge. |
| 181 | 15mm nominal bore |
| 182 | Providing and fixing uplasticised PVC connection pipe with brass unions : |
| 183 | 60 cm length |
| 184 | 15 mm nominal bore |
| 185 | Providing and fixing UPVC (Schedule 80) pipes, including all UPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step UPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall |
| 186 | Internal work - Exposed on wall |
| 187 | 15 mm nominal bore |
| 188 | 20 mm nominal bore |
| 189 | 25 mm nominal bore |
| 190 | 32 mm nominal bore |
| 191 | 40 mm nominal bore |
| 192 | Providing and fixing UPVC valve of approved quality : |
| 193 | 25 mm nominal bore |
| 194 | 32 mm nominal bore |
| 195 | 40 mm nominal bore |
| 196 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : |
| 197 | 25 mm nominal bore |
| 198 | Providing and fixing PVC bib cock of \"Prayag\" make or approved equivalentquality and colour including dismantling of existing Bib cock wherever required as per the direction of Engineer in charge. |
| 199 | 15mm nominal bore |
| 200 | Providing and fixing PVC stop cock/Angle Cock of \"Prayag\" make or approved equivalentquality and colour including dismantling of existing stop cock wherever required as per the direction of Engineer in charge. |
| 201 | 15 mm nominal bore |
| 202 | Providing and fixing PVC Pillar cock of \"Prayag\" make or approved equivalentquality and colour including dismantling of existing Pillar cock wherever required as per the direction of Engineer in charge. |
| 203 | 15 mm nominal bore |
| 204 | Providing and fixing PVC urinal spreader of \"Prayag\" make or approved equivalentquality and colour including dismantling of existing spreader wherever required as per the direction of Engineer in charge. |
| 205 | 15 mm nominal bore |
| 206 | Providing and fixing S.S. grating ofapproved quality for Floor Trap including dismantling of existing jali wherever required etc. complete as per the direction of Engineer in charge. |
| 207 | 150x150 mm |
| 208 | Replacement of 25mm nominal bore C.P brass flush cock of standard design and of existing available make or approved equivalent in existing concealed G.I. line including replacement of existing G.I. pipe fittings wherever required and making good the walls with white cment etc. complete as per the direction of Engineer in charge. |
| 209 | Repairs to leakage/unserviceability of 15mm nominal bore C.P. brass/Brass bib / stop cock/pillar cock, brass urinal spreader, shower, flush tank etc. fixed in existing G.I. pipe line by necessary replacing rubber washer or with Taphlon tap or cleaning with acidas required etc. all complete including dismantling the same whereverrequired as per the direction of Engineer-in-charge. The item includes labour charges along with cost of providing necessary rubber washer for bib cock/stop cock/Flush tank, taphlon tap, acid required to repair the leakage/unserviceability. |
| 210 | Replacement of 15mm nominal bore brass spindle for bib cock/stop cock/pillar cocks all complete as directed by Enginner-in-charge. |
| 211 | Replacement of 15mm nominal bore ceramic spindle for bib cock/stop cock/pillar cocks all complete as directed by Enginner-in-charge. |
| 212 | Replacement of existing Gun metal wheel valve/ brass handle valve and necessary G. I. pipes and fitting with Brass handle valve (screwed end) of approved make and quality including necessary G.I. pipe and fittings of required length in existing G.I. pipe line etc. complete as per the direction of Engineer in charge. |
| 213 | 25 mm nominal bore. |
| 214 | 32 mm nominal bore. |
| 215 | Providing and fixing temporary wooden scaffolding made from bamboo and ballies up to any floor level for repairing work on building face. Maintaining it in a serviceable condition for the required duration and removing it after completion of repairing work etc. all complete as per the direction of Engineer-in-charge. The elevation area of the scaffolding shall be measured for the payment purpose. Scaffolding material shall be property of contractor after removal. |
| 216 | Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality |
| 217 | L D - 2.5 |
| 218 | Rectangular shape 600x450 mm internal dimensions |
| 219 | Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : |
| 220 | For pipes 100 to 250 mm diameter |
| 221 | Supplying and fixing Precast RCC cover 300x300 mm with frame for gully trap (standard pattern) including dismantling of existing gully trap cover with frame wherever required etc. complete as per the direction of Engineer in charge. |
| 222 | Cleaning ofmanholes, Gully Traps, floor Traps, etc. including connectedsewer/sludge lines by rodding, passing Bamboo strips, a jute ball etc. and flowing clean water etc. to ensure proper flow through linesto the satisfaction of Engineer in charge. The rate includes the cost of all tools, plants and labour involved in above operations including disposal of garbage to approved dumping ground and also safety measures of labourers are to be taken by agency during execution of work. The payment shall be paid on Nos. of manholes, Gully Traps, Floor Traps, etc. cleaned. |
| 223 | Manhole up to 1.5m deep. |
| 224 | Gully Trap |
| 225 | Floor Trap/Nahni Trap |
| 226 | Removing loose plaster/concrete from slabs and beamsmanually by Chisel and light hammer including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris upto 50m lead and for all lifts all complete as per direction of Engineer-In-Charge |
| 227 | Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of Engineer-In-Charge. |
| 228 | Bars upto 12 mm diameter |
| 229 | Bars above 12 mm diameter |
| 230 | Providing, mixing and applying bonding coat of approved adhesive on chipped portion of RCC as per specifications and direction of Engineer-In-charge complete in all respect. |
| 231 | SBR Polymer (@10% of cement weight) modified cementitious bond coat @ 2.2 kg cement per sqm of surface area mixed with specified proportion of approved polymer |
| 232 | Providing, mixing and applying SBR polymer (of approved make) modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of Engineer-in-charge. |
| 233 | 20 mm average thickness. |
| 234 | Providing IInd class Plumber / IInd class Carpenter / IInd class Mason for attending maintenance works which is not covered in main related Basic items etc. complete as directed by Enginner-in-charge. |
| 235 | Providing Beldar / Coolie / Helper for attending maintenance works which is not covered in main related Basic items etc. complete as directed by Enginner-in-charge. |
| 236 | Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba, Excavating filled sunken flooring for providing and fixing 100 mm dia. PVC pipe and fittings for making drainage connection to European WC pan including providing PVC Nahni Trap for disposal of water and refilling the same with cement mortarfor making good the floor after making drainage connection etc. all complete as per directions of Engineer-in-Charge. The Item includes cost of materials like providing 110 mm PVC drainage pipes approx. length 1.00m, 110mm dia. PVC Tee- 1 No., 110x75mm PVC reducer, 75mm dia. PVC drainage pipe approx. 0.30m, 75mm dia. PVC coupler and 110x65mm PVC Nahni Trap, PVC solutions, cost of labours, tools & plants etc. to complete the Job. |
| 237 | Repairs to leakage of S.C.I. soil pipe of any dia. on walls/ in walls at height up to floor Five level by rodding with jute balls/ removalof blockage of joints by opening Joint bend/Tee access to clean the blockage of soil pipe and fittings or by removing blockage by making punture and repairing of punturedS.C.I. pipe by replacing with PVC soil pipe up to 2 feet length and fittings if required including necessary dismantling, cutting, and making good the walls , floors, chhajjas etc. completeas per the direction of Engineer in charge. The item includes necessary materials, labours, scaffolding, Tool & plants, insurance etc. to complete the Job. |
| 238 | For SCI pipe up to 100mm dia. |
| 239 | Repairs to leakage of 15mm dia. G.I. water supply line by replacement of rusted 15mm dia. G.I. Elbow/15mm dia. G.I. Coupling/G.I. Nipple up to 150mm long and making good the walls after repairing etc. complete as per the direction of Engineer in charge. The item includes necessary materials, labours, scaffolding, Tool & plants etc. to complete the Job. |
| 240 | Uprooting trees from the wall, roof and all parts of the building by using scaffolding (from floor one to floor five) and thenputting acid and cleaning the dust, dirt and disposing the garbage beyond the municipality area limits and making good the surface with cement concrete / cement mortar etc. complete as per the directionof Engineer-in-charge. The rate shall be inclusive of material costs, labour charges, carriage/ transportation, tools and plants, equipments and incidentals all complete and nothing extra shall be paid on any account unless otherwise specifically mentioned in the item. |
