Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Civil Construction Work |
| 2 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 4 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. |
| 5 | Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20mm nominal size derived from natural sources). |
| 6 | Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer\"s specification. |
| 7 | Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. |
| 8 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. |
| 9 | Providing and applying primer coat with bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.70 kg/sqm using mechanical means as per clasuse 502 of specification. |
| 10 | Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. |
| 11 | Reinforced cement concrete work in beams, suspended foors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 12 | Add for using extra cement in the items of design mix over and above the specified cement content therein. |
| 13 | Dry Lean Cement Concrete Sub- base (Construction o, dry lean cement concrele SUU base over a prepared suugrade with coarse and fine aggregale conforming to lS: 383, the size of coarse aggregate not exceeding 26.5 mm, aggregate cement ratjo not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cemenl content not to be less than 150 kg/ cum, oplimum moisture content to be determined during lrial length construction, concrete strength not to be less than 1O N,lpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonnes vibratory roller, finishing and curing as per clause 601 of specifications complete in all respect |
| 14 | Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. |
| 15 | Construction of Un-Reinforced Dowel Jointed Plain Cement Concrete pavement M-30 Grade concrete over a prepared sub base with cement,coarse and fine aggregate conferming to IS-383, Maximum size of coarse aggregate not exceeding 25mm, mixed in a batching and mixing plant as per approved mix design,transported to site, laid with the fixed form or slip form paver, spread compacted and finished in a continuos operation including provision or contraction, expansion, construction and longitudinal joints,joint filler, seperation member, sealant primer,joint sealant, debonding strip,admixer as approved, curring compound,finishing to lines and grades as per drawing as per IRC-15-2011 and as per relavant clause of section 602 of specification complete but including cost of steel in dowel bar and tie rod etc. |
| 16 | Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand). |
| 17 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 18 | Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4 mm thick aluminium composite panel material consisting of 3 mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5 mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face# 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. (c) The fastening brackets of Aluminium alloy 6005 TS / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium items. The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architecral drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places. |
| 19 | Extra for fixing marble / granite stone over and above corresponding basic item, in facia and drops of width upto 150mm with epoxy resin baesd adhesive including cleaning etc. complete. |
| 20 | Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble/Granite/Stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edge etc. complete. |
| 21 | Providing and fixing bright finished brass 100 mm mortice latch and lock, lSl marked, with six levers and a pair of anodised (anodic coating not less than grade Ac 10 as per 15 : 1868) aluminium lever handles of approved quality with necessary screws etc. complete |
| 22 | Providing and fixing sliding arrangement in racks/ cupboards/cabinets shutter by with stainless steel rollers to run inside C or E aluminium channel section (The payment of C or E channel shall be made separately) |
| 23 | Providing and fixing PVC rigid foam sheet 1 mm thick on existing door shutters (bathroom and W.C. doors) using synthetic rubber based adhesive. |
| 24 | Providing and fixing steel (white power coated) crescent lock for uPVC / aluminium sliding window/ door with necessary screws etc. complete. |
| 25 | Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). |
| 26 | Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. |
| 27 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with lsi, ls : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 7o1 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. |
| 28 | Providing and fixing aluminium pull bolt lock, ISI marked, anodised (anodiccoating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws bolts, nut and washers etc. complete. |
| 29 | Providing and fixing 50 cm long aluminium kicking plate of size 100x3.15 mm, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete. |
| 30 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 31 | Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing. |
| 32 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) |
| 33 | Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer. |
| 34 | Extra for pre finished nosing to treads of steps of marble stone. |
| 35 | Extra for marble stone flooring in treads of steps and risers using single length up to 2.00 metre. |
| 36 | Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. |
| 37 | Extra for pre finished nosing to treads of steps of marble stone. |
| 38 | Providing and fixing M.S. angle 50x50x5 mm to act as nosing with lugs of M.S. flat 10x5 mm, 10 cm long, forked at end 60cm apart (minimum three lugs to be provided), including necessary welding and applying a priming coat of approved primer on exposed surface etc. complete. Supplying fitting Angles size in mm as per I.S. 226 |
| 39 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete. |
| 40 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. |
| 41 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 42 | 18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand). |
| 43 | Neat cement punning. |
| 44 | Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers. |
| 45 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete |
| 46 | Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron ‘Y’ shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5 mm thick) wire of high tensile strength of 165 kg/ sq. mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately) |
| 47 | Providing and laying Dense Graded Bituminous Macadam using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equiped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers as per specifications to achieve the desired compaction and density, complete as per specificatons and directions of Engineer-in-Charge.50 to 100 mm average compacted thickness with bitumen of grade VG-30 @ 5% (percentage by weight of total mix)and lime filler @ 2% (percentage by weight of Aggregate)prepared in Batch Type Hot Mix Plant of 100- 120 TPH capacity. |
| 48 | Providing and laying Bituminous concrete using crushed stoneaggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equiped with electronic sensor to the required grade,level and alignment and rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction and density as per specification, complete and as per directions of Engineer-in-Charge.40/50 mm compacted thickness with bitumen of grade VG- 30 @ 5.5% (percentage by weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate)prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity. |
| 49 | Manufacturing, supplying and fixing retro reflective overhead signageboards made up of 2 mm thick aluminium sheet, face to be fullycovered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type - III of ASTM-D-4956-01 as approved by Engineer-in-charge, letters, borders etc. as per IRC: 67-2001 in silver white with blue colour back ground and with highintensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class II of ASTM-D-4956-01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys,rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminium sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawings, specification and direction of the engineer-in-charge.(Structural frame work including M.S. plate to be providedseparately. Rectangular area of the sheet only shall be measured for payment).Overhead informatory road signage |
| 50 | Providing Retro-reflective regulatory sign board of size 900 mm dia meter made out of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated lens type retro -reflective sheeting as approved by Engineer-incharge . Letter, symbols, borders etc. will be as per IRC - 67 with required colour scheme on the boards and with the high intensity grade A. The aluminium sheet to be riveted to M.S. frame of angle iron of size 40x40x4 mm. The boards will be fixed to 1 No. 50x50 mm square post made of M.S. angle 50x50x4 mm, 4 m long welded to the frame with adequate anti-theft arrangement .Sheet work to be painted with two or more coats of synthetic enamel paint over an under coat (primer) and back side of aluminium sheet to be painted with two or more coats of epoxy paint including appropriate priming coat complete in all respects as per direction of Engineer-in-charge. |
| 51 | Providing and applying 2.5 mm thick road marking strips (retro-reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineerin-charge and accordance with applicable specifications |
| 52 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarsesand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as perdirection of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). |
| 53 | Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads& lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge.With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30 |
| 54 | Providing, laying, spreading and compacting graded stone aggregate(size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in uniform layers with mechanical paverfinisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achievethe desired density, complete as per specifications and directions of Engineer-in-Charge. |
| 55 | Construction of dry lean cement concrete sub base over a prepared sub-grade with coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per specifications, cement content not to be less than 150 Kg/cum,optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7days, mixed in a batching plant, transported to site, for all leads &lifts, laid with a mechanical paver, compacting with 8-10 tonne vibratory roller, finishing and curing etc. complete as per direction of Engineer-in- charge. |
| 56 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 18.49.1 15 mm nominal bore |
| 57 | Supplying and fixing C.I. cover without frame for manholes: 500 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg |
| 58 | Providing and fixing 12mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer in charge (Door handle, lock and stopper etc. to be paid separately) |
| 59 | Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. |
| 60 | Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment. |
| 61 | Providing, assembling and supplying vision glass panels (IGUs)comprising of hermetically-sealed 6-12- 6 mm insulated glass (doubleglazed) vision panel units of size and shape as required and specified,comprising of an outer heat strengthened float glass 6mm thick, ofapproved colour and shade with reflective soft coating on surface # 2of approved colour and shade, an inner Heat strengthned clear floatglass 6mm thick, spacer tube 12mm wide, dessicants, includingprimary seal and secondary seal (structural silicone sealant) etc. allcomplete for the required performances, as per the Architecturaldrawings, as per the approved shop drawings, as specified and asdirected by the Engineer-in Charge. The IGUs shall be assembled inthe factory/ workshop of the glass processor.(Payment for fixing of IGU Panels in the curtain glazing is included incost of item No.25.2)For payment, only the actual area of glass on face # 1 of the glasspanels (excluding the areas of the grooves and weather siliconesealant) provided and fixed in position, shall be measured in sqm. (i) Coloured tinted float glass 6mm thick substrate with reflectivesoft coating on face # 2, + 12mm Airgap + 6mm HeatStrengthened clear Glass of approved make having propertiesas visible Light transmittance (VLT) of 25 to 35 %, Lightreflection internal 10 to 15%, light reflection external 10 to 20%, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall bedecided by technical sanctioning authority as per the siterequirement. |
| 62 | Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer- inCharge. |
| 63 | Providing, assembling and supplying vision glass panels (IGUs)comprising of hermetically-sealed 6-12- 6 mm insulated glass (doubleglazed) vision panel units of size and shape as required and specified,comprising of an outer heat strengthened float glass 6mm thick, ofapproved colour and shade with reflective soft coating on surface # 2of approved colour and shade, an inner Heat strengthned clear floatglass 6mm thick, spacer tube 12mm wide, dessicants, includingprimary seal and secondary seal (structural silicone sealant) etc. allcomplete for the required performances, as per the Architecturaldrawings, as per the approved shop drawings, as specified and asdirected by the Engineer-in Charge. The IGUs shall be assembled inthe factory/ workshop of the glass processor.(Payment for fixing of IGU Panels in the curtain glazing is included incost of item No.25.2)For payment, only the actual area of glass on face # 1 of the glasspanels (excluding the areas of the grooves and weather siliconesealant) provided and fixed in position, shall be measured in sqm. (i) Coloured tinted float glass 6mm thick substrate with reflectivesoft coating on face # 2, + 12mm Airgap + 6mm HeatStrengthened clear Glass of approved make having propertiesas visible Light transmittance (VLT) of 25 to 35 %, Lightreflection internal 10 to 15%, light reflection external 10 to 20%, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall bedecided by technical sanctioning authority as per the siterequirement. |
| 64 | Providing and laying 60mm thick factory made cement concrete paver block of approved shape and colour of M -30 grade made of C&D waste by block making machine with vibratory compaction laid in required pattern and including over 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Enganeer-in-charge. |
| 65 | Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.200 mm clamp |
| 66 | 12 mm cement plaster finished with a floating coat of neat cement of mix 1:4 (1 cement: 4 fine sandl |
| 67 | Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 68 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement i 6 coarse sand) |
| 69 | Development of tube well in accordance with IS : 2800 (part I) andIS: 11189, to establish maximum rate of usable water yield withoutsand content (beyond permissible limit), with required capacity aircompressor, running the compressor for required time till well isfully developed, measuring yield of well by \"V\" notch method or anyother approved method, measuring static level & draw down etc. bystep draw down method, collecting water samples & getting testedin approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessoriesetc., all as per requirement and direction of Engineer-in-charge |
| 70 | Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:200 mm dia |
| 71 | Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia |
| 72 | Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge 150 mm nominal size dia |
| 73 | Supplying, filling, spreading & leveling stone boulders of size range5 cm to 20 cm, in recharge pit, in the required thickness, for allleads & lifts, all complete as per direction of Engineer-in-charge |
| 74 | Supplying, filling, spreading & leveling coarse sand of size range 1.5 mmto 2 mm in recharge pit, in required thickness over gravel layer, for all leads& lifts, all complete as per direction of Engineer -in-charge |
| 75 | Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge |
| 76 | Carriage of Materials with Machine Loading. Earth By mechanical transport including loading, unloading and stacking. (Lead upto 5KM away from the site) |
| 77 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes |
| 78 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 79 | Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 mm dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge. 10 x 60 mm |
| 80 | Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. Sutset plates at the junctions and corners, all necessary fittings complete, includinB applying a priming coat of approved steel primer. UsinB M.S. angels 40x40x6 mm for diagonal braces |
| 81 | Brick on edge flooring with bricks of class designation 7.5 on a bed of 12 mm cement mortar, including filling the joints with same mortar, with common burnt clay non modular bricks:1:4 (1 cement : 4 coarse sand) |
| 82 | Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). Light shade pigment using white cement |
| 83 | Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slu.ry mixed with pigment to match the shade of tiles, including rubbin8 and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). Dark shade pigment using ordinary cement |
| 84 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbingand polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick. |
| 85 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40mm thick with 20mm nominal size stone aggregate. |
| 86 | 25 mm wooden planking, tongued and grooved in flooring, including fixing with iron screws complete with :Second class teak wood |
| 87 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm |
| 88 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Size of Tile 600 x 600 mm |
| 89 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size (Size of Tile 600 x 600 mm ) |
| 90 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 1200 mm |
| 91 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm |
| 92 | Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. |
| 93 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent |
| 94 | Providing and laying gola 75x75mm in cement concrete M15 grade including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design in 75x75 mm deep chase. |
| 95 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes:75 mm diameter |
| 96 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diaMeter. |
| 97 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Coupler 110 mm |
| 98 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5°.110 mm bend |
| 99 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Shoe (Plain). 110 mm Shoe. |
| 100 | Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated \"J\" or \"L\" hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. 2 mm thick corrugated (2.5\" or 4.2\" or 6\") or step-down (2\" or 3\" or 6\" ) as specified |
| 101 | Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50mm (base metal of minimum 0.45mm thickness with total coating thickness of 0.05mm) with Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15- 18 microns using self drilling/ self tapping screws cmplete: 12.51.1 Ridges plain (500 - 600mm) :Ridges plain (500 - 500mm) |
| 102 | Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50mm (base metal of minimum 0.45mm thickness with total coating thickness of 0.05mm) with Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15- 18 microns using self drilling/ self tapping screws cmplete: 12.51.1 Ridges plain (500 - 600mm) Flashings/ Aprons.( Upto 600 mm) |
| 103 | Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50mm (base metal of minimum 0.45mm thickness with total coating thickness of 0.05mm) with Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15- 18 microns using self drilling/ self tapping screws cmplete: 12.51.1 Ridges plain (500 - 600mm) Gutter (600 mm over all girth) |
| 104 | Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steelsections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main \"T\" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at1200 mm center to center and cross \"T\" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main \"T\" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross \"T\" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main \"T\"runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm die and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8mm spaced at 1200 mm center to center along main T,bottom exposed width of 24 mm of all T-sections shall bepre- painted with polyester paint, all complete for allheights as per specifications, drawings and as directed by120 Engineer-in-charge.GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending. |
| 105 | 12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand) |
| 106 | 6 mm cement plaster of mix : 1:3 (1 cement: 3 fine sand) |
| 107 | 12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand) |
| 108 | Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm |
| 109 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: 13.47.1 New work (Two or more coats applied @ 1.43 Itr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) |
| 110 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/ 10 sqm of approved brand or manufacture |
| 111 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work |
| 112 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture . |
| 113 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture |
| 114 | Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats. |
| 115 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre |
| 116 | Supplying and stacking at site. Good earth |
| 117 | Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. Made of G.I. wire of dia. 4 mm, PVC coated to achieve outer dia not less than 5 mm in required colour and shade |
| 118 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore |
| 119 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 32 mm nominal bore. |
| 120 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 40 mm nominal bore |
| 121 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 50 mm nominal bore |
| 122 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall : 25 mm nominal dia Pipes |
| 123 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall : 32 mm nominal dia Pipes |
| 124 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall : 40 mm nominal dia Pipes |
| 125 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall : 50 mm nominal dia Pipes |
| 126 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 100 mm nominal dia Pipes |
| 127 | Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design : With 20 mm diameter round bar |
| 128 | Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality Circular shape 560 mm internal dia |
| 129 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg(weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1. cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc, complete as per standard design: With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 130 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1. cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc, complete as per standard design:Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets:With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 131 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing ofjoints etc. complete : 150 mm |
| 132 | Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, by mechinical / manual means ramming of bottoms, for all depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m: Pipes, cables, etc. exceeding 80mm dia but not exceeding 300mm dia. |
| 133 | Close timbering in trenches including strutting, shoring and packing cavities (wherever required) complete. (Measurements to be taken of the face area timbered).Depth exceeding 1.5 m but not exceeding 3 m |
| 134 | Close timbering in case of shafts, wells, cesspits, manholes and the like including strutting, shoring and packing cavities (wherever required) etc. complete. (Measurements to be taken of the face area timbered).Depth exceeding 1.5 m but not exceeding 3 m |
| 135 | Excavating, supplying, stacking and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in foundation, trenches, plinth, sides of foundation etc. complete for all lift. |
| 136 | Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials. All kinds of soil |
| 137 | Surface dressing of the ground including removing vegetation and in- equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m.2.28.1 All kinds of soil |
| 138 | Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/Lindane emulsifiable Concentration 20% |
| 139 | Along external wall where the apron is not provided using chemical emulsion @ 7.5 litres / sqm of the vertical surface of the substructure to a depth of 300mm including excavation channel along the wall & rodding etc. complete: With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration |
| 140 | Diluting and injecting chemical emulsion for POSTCONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : 2.35.1 Along external wall where With Chlorpyriphos/Lindane E.C. 20% with 1% concentration |
| 141 | Excavation of Foundation- Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge: All kinds of soil |
| 142 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil |
| 143 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron) |
| 144 | Providing and fxing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size,including necessary filling up the gaps at junctions, i.e. attop, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth,rust free, straight, mitred and jointed mechanicallywherever required including cleat angle, Aluminium snapbeading for glazing I paneling, C.P. brass / stainless steelscrews, all complete as per architectural drawings and thedirections of Engineer-in-charge. (Glazing, paneling and dashfasteners to be paid for separately) : Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 145 | Providing and fixing glazing in aluminium door, window,ventilator shutters and partitions etc. with EPDM rubber /neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost ofaluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) |
| 146 | Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. Upto 5mm depth and 5 mm width |
| 147 | Grading roof for water proofing treatment with.Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) |
| 148 | Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks,roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI- 212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks upto a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage. For horizontal surface one coat @1.10 kg per sqm |
| 149 | Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying: (a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. (c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately.For the purpose of measurement the entire treated surface will be measured. |
| 150 | Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 mild steel screwed and socketed/plain ended casing pipes of required dia, conforming to IS: 4270, of reputed & approved make, including painted with outside surface with two coats of anticorrosive paint of approved brand and manufacture, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer-in-charge.200 mm nominal size dia having minimum wall thickness 5.40 mm |
| 151 | Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, allcomplete for borewell of 150 mm dia |
| 152 | Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level.ALL TYPES OF SOIL 300 mm dia |
| 153 | Providing and fixing at all height wall panelling with phenol bonded Bamboo Mat board conforming to IS:13958-1994 including providing and fixing to frame work made of 50 mm x 50 mm hard wood plugs including cutting brick work and fixing in cement mortar and making good the wall etc. and also providing and fixing wooden moulded corner beading of triangular shape to the junction of panelling etc. with iron screws all complete as per direction of Engineer-in-Charge.12 mm thickness |
| 154 | Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI- 212-3R-2010 i.e byreducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage. Frame size 65 x 125 mm |
| 155 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 156 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from atural sources :6 graded stoe aggeegate 20mm nominal size derived from natural sources) |
| 157 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) |
| 158 | Construction ot granular sub-base by providing well graded material like natural sand crushed gravel or crushed stone having CBR >30, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method at OMC with rotavator and compacting with vibratory rollers of 80 to 100 kN static weight to achieve the desired density, complete as per Clause 40l of Specification. GSB with grading material -1 |
| 159 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses,parapets, coping, bed blocks, anchor blocks, plain window ,sills, fillets, sunken floor etc., up to floor five level,excluding the cost of centering, shuttering and finishing: 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 160 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 161 | Centering and shuttering including strutting, propping etc. and removal of form work for: Foundations, footings, bases for columns. |
| 162 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources) |
| 163 | Seal Coat : Providing and laying of premix sand seal coat with HMP of appropriate capacity not less than 75 tonnes/ hours using crushed stone chipping (aggregate shall pass through 2.36mm sieve and retained on 180 micron sieve and bitumin of suitable qrade All compete as per clause 511 of specifications) |
| 164 | Providing and applying tack coat wilh bitumen emulsion using distributor at lhe rate of 0.2kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom and as per relevant clauses of section-503 of specifcations.@ 0.25 kg per sqm (normal bituminous surfaces) |
| 165 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fllets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement: 5.2.2 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 166 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 167 | Steel reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 168 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 toaccelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall bepayable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth levelConcrete of M25 grade with minimum cement content of 330 kg /cum |
| 169 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, badmixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works above plinth level upto floor V level Concrete of M25 grade with minimum cement content of 330 kg /cum. |
| 170 | Centering and shuttering including strutting, propping etc. and removal of form for foundations, footings, bases of columns, etc. for massconcrete |
| 171 | Centering and shuttering including strutting, propping etc. and removal of form for Edges of slabs and breaks in floors and walls Under 20 cm wide. |
| 172 | Centering and shuttering including strutting, propping etc. and removal of form for Weather shade, Chajjas, corbels etc., including edges |
| 173 | Centering and shuttering including strutting, propping etc. and removal of form for Walls (any thickness) including attached pilasters, buttererses, plinth andstring courses etc. |
| 174 | Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform |
| 175 | Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platfor |
| 176 | Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 177 | Centering and shuttering including strutting, propping etc. and removal of form for all heights : Columns,Pillars, Piers, Abutments, Posts and Struts. |
| 178 | Centering and shuttering including strutting, propping etc. and removal of form for Stairs, (excluding landings) except spiral-staircases. |
| 179 | Brick work with common burnt clay machine moulded perforated modular bricks of class designation 12.5 conforming to IS : 2222 in exposed brick work including making horizontal and vertical grooves 10 mm wide 12mm deep complete in cement mortar 1:6 (1 cement :6 coarse sand).From ground level upto plinth level |
| 180 | Brick work with clay flyash F.P.S. (non modular) brick of class designation 7.5 in superstructure above plinth level up to floor five level in : Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 181 | Brick work with non modular fly ash bricks conforminS to ls:12894, class designation 10 average compressive streneth in super structure above plinth level up to floor V level ih : Cement mortar 1:6 (1 cement : 6 Coarse sand) |
| 182 | Brick work with non modular fly ash bricks conforminS to ls:12894, class designation 10 average compressive streneth in super structure above plinth level up to floor V level ih : Cement mortar 1:6 (1 cement : 6 Coarse sand) |
| 183 | Half brick masonry with non modular fly ash bricks of class designation 10, conformingio IS :12894, in super structure above plinth and upto floor V level. Cement mortar 1 : 4 (1 cement : 4 coarse sand) |
| 184 | Half brick masonry with non modular fly ash bricks of class designation 10, conformingio IS :12894, in super structure above plinth and upto floor V level. Cement mortar 1 : 4 (1 cement : 4 coarse sand) |
| 185 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. Granite stone slab of colour black, Cherry/Ruby red Area of slab upto 0.50 sqm |
| 186 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. Granite stone slab of colour black, Cherry/Ruby red Area of slab upto 0.50 sqm |
| 187 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. Granite stone slab of colour black, Cherry/Ruby red Area of slab over 0.50 sqm |
| 188 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. Granite stone slab of colour black, Cherry/Ruby red Area of slab over 0.50 sqm |
| 189 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. Granite stone slab of colour black, Cherry/Ruby red Area of slab over 0.50 sqm |
| 190 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work |
| 191 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125mm |
| 192 | Providing and fixing aluminium hanging floor door stopper, l5l marked, anodised (anodic coatinS not less than grade AC 10 as per 15 : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper |
| 193 | Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows, Doors and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete. With 12 mm mild steel U beading |
| 194 | Two and half track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. Using R2 series with frame (65mm & above) x (40mm & above) & glazed sash (25mm & above) x (50mm & above) & fly screen sash (18mm & above) x (40mm & above) with zinc alloy (zamak) powder coated touch locks with hook (Height upto 1.2 meter). |
| 195 | Ventilator Casement window single panel with or without fixed panel with S.S. 304 friction hinges as per size and weight of sash, single point locking zinc alloy (zamak) powder coated handles. Using R3 series with frame (55mm & above) x (45mm & above) & sash /mullion (55mm & above) x (65mm & above). (Height above 1.2 meter) |
| 196 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 197 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering withvertical grains or cross bands and face veneers on both faces of shutters. 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 198 | Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete :2nd class teak wood.50x12 mm. |
| 199 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc. |
| 200 | Providing and fixing aluminium sliding door bolts, ISI marked anodised anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16mm |
| 201 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 250X16 mm |
| 202 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 300x10 mm |
| 203 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 150x10 mm |
| 204 | Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows, Doors and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete. With aluminium Snap beading. |
| 205 | Providing and fixing machine cut, mirror/ eggshell polished , Marble stone work for wall lining (veneer work) including dado, skirting, risers of steps etc., in required design and pattern (if required with marble stone slab pieces of different shapes, sizes & texture but of even thickness) on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with white cement slurry @ 3.3 kg/sqm including pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing, polishing etc. all complete as per Architectural drawings, and as directed by the Engineer-in Charge. 18 mm thick Italian Marble stone slab,Perlato, Rosso verona, Fire Red or Dark Emperadore etc. |
| 206 | Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials.All kinds of soil |
| 207 | Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials. All kinds of soil |
| 208 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted withspecial shaped washers etc. complete. Hot finished welded type tubes |
| 209 | Designing, fabricating, testing, protection, installing and fixing inposition semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including: (a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design oft he aluminum sections for fixing glazing panels of varioust hicknesses, aluminium cleats, sleeves and splice plates etc.gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)-cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including: .................................................................complete description given in NIT page No. 151-152 |
| 210 | Plumbing Works |
| 211 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, lS : 127O1 marked, with cover and suitable locking arran8ement and making ne.essary holes for inlet, outlet and overflow pipes but without fittings afld the base support for tank. |
| 212 | Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality :32 mm nominal dia Pipes |
| 213 | Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality :40 mm nominal dia Pipes |
| 214 | Providing and flxing PTMT grating of approved quality and colour. Circular type 100 mm nominal dia |
| 215 | Providing and firing 100 mm sand cast lron grating for gully trap. |
| 216 | Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge. |
| 217 | 15 mm nominal bore |
| 218 | Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length , 15 mm nominal bore |
| 219 | Providing and fixing P.V.C. Waste pipe for sink or wash basin including P.V.C. waste fittings complete. 40 mm dia. |
| 220 | Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. Waste coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 gms |
| 221 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. |
| 222 | Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade Two or more coats on new worke |
| 223 | Providing and fixing on wall face unplasticised - UPVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. 110mm Dia coupler |
| 224 | Providing and filling the joints with spun yarn cement slurry and cement mortar 1:2 (1 cement: 2 fine sand) in S.C. I I C. I pipes 100 mm dia pipe |
| 225 | Providing and filling sand of grading zone V or coarser grade alround the GI pipes in external work. 32 mm nominal dia Pipes |
| 226 | Providing and filling sand of grading zone V or coarser grade alround the GI pipes in external work. 40 mm nominal dia Pipes |
| 227 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. |
| 228 | Providing and fixing plain bend of required degree. 75mm dia Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905 |
| 229 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 15mm nominal outer dia .Pipes. |
| 230 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. |
| 231 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall20 mm nominal dia Pipes |
| 232 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion, (i) Single socketed pipes 110 mm dia |
| 233 | Providing and fixing plain bend of required degree. 100mm dia Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905 |
| 234 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :15 mm nominal bore |
| 235 | Providing and fixing brass stop cock of approved quality : 15 mm nominal bore |
| 236 | Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof. |
| 237 | Providing and fixing shielded coupling for Hubless centrifugally cast iron pipe. 100mm dia SS 304 grade coupling with EPDM rubber gasket |
| 238 | Providing and fixing terminal guard. 100 mm Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 |
| 239 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall25 mm nominal dia Pipes |
| 240 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :20 mm nominal bore |
| 241 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :25 mm nominal bore |
| 242 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc. 15 mm nominal dia Pipes |
| 243 | Providing and fixing heel rest sanitary bend: 100 mm dia Sand cast iron S&S as per IS:3989 |
| 244 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in ChargeInternal work - Exposed on wall 32 mm nominal dia Pipes |
| 245 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc. 20 mm nominal dia Pipes |
| 246 | Providing and fixing gun metal gate valve with c.l. wheel of approved quality lscrewed endl : 20 mm nominal bore |
| 247 | Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts 100 mm diaHubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905 |
| 248 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 75 mm outlet Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 |
| 249 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.32 mm nominal dia Pipes |
| 250 | Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter : 100mm dia |
| 251 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:893115 mm nominal bore |
| 252 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 32 mm nominal bore |
| 253 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe |
| 254 | Providing and fixing door piece, insertion rubber washer 3mm thick, bolts & nuts complete : 100 mm Sand cast iron S&S as per IS - 3989 |
| 255 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms |
| 256 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc. 25 mm nominal dia Pipes |
| 257 | Providing and fixing gun metal gate valve with c.l. wheel of approved quality lscrewed endl : 25 mm nominal bore |
| 258 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.40 mm nominal dia Pipes |
| 259 | Providing and fixing toilet paper holder : C.P. brass |
| 260 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.Internal work - Exposed on Wall For Roof32 mm dia nominal bore |
| 261 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in ChargeInternal work - Exposed on wall 40 mm nominal dia Pipes |
| 262 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work including cutting chases and making good the walls etc. 32 mm nominal dia Pipes |
| 263 | 32mm nominal dia |
| 264 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 40 mm nominal bore |
| 265 | Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 100x100x100 mm Sand cast iron S&S as per IS - 3989 |
| 266 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 100 mm outlet Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 |
| 267 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 250 mm dia. R.C.C. Pipe |
| 268 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :25 mm dia nominal bore |
| 269 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.Internal work - Exposed on Wall For Roof 40 mm dia nominal bore |
| 270 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 50 mm nominal bore |
| 271 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :32 mm dia nominal bore |
| 272 | Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long 5crews, rawl plugs etc., complete. |
| 273 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall50 mm nominal dia Pipes |
| 274 | 40mm nominal dia |
| 275 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :40 mm dia nominal bore |
| 276 | Providing and fixing soil, waste and vent pipes 100mm dia Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905 |
| 277 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.Internal work - Exposed on Wall For Roof 50 mm dia nominal bore |
| 278 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing . Oval shape 450x350 mm (outer dimensions) |
| 279 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :50 mm dia nominal bore |
| 280 | Providing and fixing gun metal non- return valve of approved quality (screwed end) : 50mm nominal dia |
| 281 | Providing and fixing gun metal non- return valve of approved quality (screwed end) :65 mm nominal bore Horizontal |
| 282 | Providing and fixing gun metal non- return valve of approved quality (screwed end) :80 mm nominal bore Horizontal |
| 283 | Providing and fixing white vitreous china squatting plate urinal with integral rim longitudinal flush pipe. |
| 284 | Providing and fixing 75 mm high, 50 mm deep and 18 mm thick stone slab table rubbed, edges rounded and polished, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. Granite Stone of approved shade |
| 285 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 510x1040 mm bowl depth 200 mm |
| 286 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design.Inside dimension 455x610mm and 45cm deep for single ppe line: With Fly Ash Brick (230x115x75mmsize) bricks of class designation 10 |
| 287 | Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. 15 mm nominal dia |
| 288 | Providing and laying cement concrete in 1:2:4 ( 1cement : 2 Coarse sand : 4 graded stone aggregate 20 mm nominal size ) and curing complete, including cost of form work. |
| 289 | Horticulture items |
| 290 | Supplying and stacking at site dump manure from approved source, including carriage upto 5 km lead complete (manure measured in stacks will be reduced by 8% for payment) : Screened through sieve of I.S designation 16mm (20 % of Earth) |
| 291 | Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately). |
| 292 | Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge. |
| 293 | Providing & laying Selection no. 1 doob grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with required tools wooden and than rolling the surface with light roller make the surface smoothen and light watering the same maintenance for 30 days or more till the grass establish properly,as per direction of officer in charge |
| 294 | Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unsaverieable material’s as per direction of officer in charge (excluding cost of plant & water)Trees Plant |
| 295 | Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unsaverieable material’s as per direction of officer in charge (excluding cost of plant & water) Shrubs Plant |
| 296 | Providing and stacking of Polyalthia longifolia (Ashok) of height 150-165 cm. in earthen pots of size 25 cm as per direction of the officer-in-charge. |
| 297 | Providing and stacking of Bottle palm of ht. 150-180 cm bottom girth 20-25 cm well developed in big poly bags of size 25 cm as per direction of the officer-in-charge. |
| 298 | Providing and stacking of Alpinia Variegated (three in one) having ht. 30 cm and above, with fresh and healthy variegated foliage in 25 cm size of Earthen Pot / Plastic Pot & as per direction of the officer-in-charge. |
| 299 | Providing and stacking of Aspidistra, having 10 to 15 leaves well developed with fresh & healthy in 25 cm size of Earthen Pot / Plastic Pot & as per direction of the officer-in-charge. |
| 300 | Providing and Displaying Acalypha green well developed, fresh & healthy with good foliage, multi branch 30 to 45 cm ht. in 20 cm size Earthen Pot/ Plastic Pot bushy plant as per direction of the officer-in-charge. |
| 301 | Providing and stacking of Calliandra hybrida of height 75-90 cm. with 4-5 branches in bag of size 25 cm as per direction of the officer-in-charge. |
| 302 | Morth Items for Road works |
| 303 | Sub-Surface drain with perforated pipe:Construction of surface drain with perforated pipe of 100 mm internal diameter of Metal/Asbastos Cement/Cement concrete/PVC ,closely jointed perforations ranging from 3mm to 6mm depending upon size of material surounding the pipe with 150mm bedding below the pipe and 300mm cushion above the pipe,crossection of excavation 450 mm x 550 mm. Excavated material to be utilised in roadway at site. |
| 304 | Embankment Construction with Material Obtaitned from Borrow Pits ( Construction Of embakment with approved material having CBR > 7, Obtained from borrow Pits with all Lifts and leads, Transporting to site , Spreading , Grading to required Slope and compacting to meet Reqirement of table 300-1, 300-2 and as per relevent clauses of section - 300 ) |
| 305 | Internal Eletricals items |
| 306 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required Group A |
| 307 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required Group C |
| 308 | Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group C |
| 309 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 6 sq. mm + 1 X 6 sq. mm earth wire (For submain wiring) |
| 310 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.4 X 6 sq. mm + 2 X 6 sq. mm earth wire (For submain wiring) |
| 311 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.4 X 10 sq. mm + 2 X 6 sq. mm earth wire (For submain wiring) |
| 312 | Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as reqired.3 X 1.5 sq. mm (For circuit wiring) |
| 313 | Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as reqired.3 X 2.5 sq. mm (For circuit wiring) |
| 314 | Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as reqired.3 X 4.0 sq. mm (For power point wiring) |
| 315 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm |
| 316 | Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. |
| 317 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required |
| 318 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings). |
| 319 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. |
| 320 | Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, \"C\" curve including connections, painting etc. as required. |
| 321 | Supplying and erecting fan hook box of 10 mm M.S. round bar bounded to the R.C.C. bars upto 50 mm length each side and pierced through a 16 S.W.G. thick aluminium/M.S. Bowl 100 mm dia. or equivalent square size and having depth upto 75 mm complete erected with duly painted by one coat of red oxide paint and two coats of paint erected in position and without any leakage of slurry of cement concrete on either side of the box and positioned to the bottom level of the slab. |
| 322 | Supplying and fixing brass batten/ angle holder includingconnection etc. as required |
| 323 | Supplying and erecting electronic type step regulator for ceiling fan |
| 324 | Supplying and erecting Energy Saving BLDC Ceiling fan 230 V A.C. 50 cycles 1200 mm, Max. Energy Consumption of 28W having service ratio (CMM/W) of Min. 8 , PF>0.9, THD<10% with IR remote control, Temperature Rise of Max. 40 deg.C, having external mounted control PCB completely erected in position as per specification no. FG-FN/CF |
| 325 | Supplying & erecting 14W, 230V integral type LED Lamp suitable for B-22/E- 27 base as per specification no. FG-LP. |
| 326 | Supplying and erecting anodized aluminium light LED fitting (4 feet) Max. 22W with high transitivity diffuser with system lumens output of Min.2200 lumens , min. efficacy of 100 lumen/W, CRI>80, CCT upto 6000K,Beam Angle of 110 deg., Ripple<5%, THD<20%, p.f. >0.95, operating range of 200-270V, surge protection of 2 kV, Life class of 50,000 Hrs at L70B50 including driver with end caps on provided PVC Block/wooded board with minimum 2 years warranty as per specification No. FG-IDF/LED. |
| 327 | Supplying and erecting LED square / circular Max. 18 W down lighter / Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 2000 Lumens, min. efficacy of 110lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5kV, Life class of 50,000 Hrs at L70B0 including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with minimum 2 years warranty as per specification No. FG-IDF/LED |
| 328 | Supplying and erecting LED square / circular Max. 7W down lighter / Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 770 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%,THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV,Life class of 50,000 Hrs at L70B50 including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with minimum 2 years warranty as per specification No. FG-IDF/LED |
| 329 | Supplying and erecting Bulk Head LED fitting Max. 10W with high transitivity diffuser with system lumens output of Min. 1100 lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., THD<10%, p.f. >0.95, operating range of 140-260V, in built surge protection of 2.5 kV, Life class of 50,000 Hrs at L70B50, IP66, IK09 rated including driver IP66, IK09 rated on provided PVC Block / wooden board with minimum 2 years warranty as per specification No. FG-IDF/LED. |
| 330 | Supplying and erecting rectangular shaped LED Panel Light (1200mm X 300mm) Max. 35 W having CRCA powder coated housing, polystyrene diffuser having system lumens output of Min. 4200 Lumens, min. efficacy of 120lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5kV, Life class of 50,000 Hrs at L70B50 including driver, having mounting arrangement with board for surface type or spring loaded mounting clipscomplete with 2 years warranty as per specification No. FG-IDF/LED. |
| 331 | Supplying and erecting exhaust fan heavy duty 230 V A.C. 50 cycles 375/380 mm. 1400 RPM complete erected in position as per specification no. FGFN/EXF |
| 332 | Supplying and erecting exhaust fan medium duty 230 V A.C. 50 cycles 225 mm. 1400 RPM with condenser complete erected in position with necessary materials. Fan motor with moisture proof treatment and ‘E’ class insulation. |
| 333 | Providing and erecting air circulator 600 mm. sweep oscillating type, wall mounting 1440 RPM without speed regulator, overheat protection unit, totally enclosed, flame proof motor suitable for 230/250 volts single phase, 50 cycles A.C. supply, core lead wire and with moisture proof treatment to winding and with ‘E’ class insulation. |
| 334 | Supplying and erecting LED square / circular Max. 11 W down lighter/Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 1200 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs at L70B50 including driver, having mountingarrangement with board for surface type or spring loaded mounting clips complete with minimum 2 years warranty as per specification No. FG-IDF/LED |
| 335 | Installation ,Testing, Commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required |
| 336 | Supplying and erecting integrated LED Highbay Fitting 135W IP65 & IK08 class having die cast aluminium housing with polycarbonate diffuser with integrated optics, having system lumens output of Min. 20000 Lumens, min. efficacy of 145 lumen/W, CRI>70, CCT upto 6500K, THD<10%, p.f. >0.90, operating range of 140-240V, inbuilt surge protection of 4kV, Life class of 50,000 Hrs at L50B50 , including driver complete with 2 Year warranty as per specification No. FG-ODF/LED. |
| 337 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)6 way (4 + 18), Double door |
| 338 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)8 way (4 + 24), Double door |
| 339 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator 6 way, Double door |
| 340 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \"C\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required Single pole |
| 341 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \"C\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required Triple pole and Neutral ( For VTPN DB) |
| 342 | Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required 40A |
| 343 | Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required 63A ( For VTPN DB) |
| 344 | Supplying and fixing following rating, double pole, 230 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required 40A |
| 345 | Supplying and fixing following rating,four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40A |
| 346 | Supplying and fixing Cable End Box (Loose Wire Box) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 Volts, on surface/ recess, complete with testing and commissioning etc.as required. For 6 way, Double door TPN MCBDB |
| 347 | Supplying and fixing Cable End Box (Loose Wire Box) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 Volts, on surface/ recess, complete with testing and commissioning etc.as required. For 8 way, Double door TPN MCBDB |
| 348 | Supplying and fixing Cable End Box (Loose Wire Box) suitable for following single pole and neutral, sheet steel, MCB distribution board, 240 Volts, on surface/ recess, complete with testing and commissioning etc.as required. For 8 way, Double door SPN MCBDB |
| 349 | Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required |
| 350 | Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board Of sheet Steel, dust protected, duly powder painted, inclusive Of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 8way TPN (4+18) double door |
| 351 | Supplying and fixing Cable End Box (Loose Wire Box) suitable for triple pole and neutral, sheet steel, Vertical MCB distribution board, 415 Volts, on surface/ recess, complete with testing andcommissioning etc. as required. |
| 352 | SUPPLY OF CABLE Supply of XLPE insulated and PVC sheathed power cable of 1.1 kV grade, 1.1 kV, multi core, aluminum,armored , underground, Conforming to IS 7098-2 Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable, 1100 V 4 core 10 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL |
| 353 | Providing & erecting 4 Pole MCCB, 415V, up to 100A, rated short-circuit breaking capacity 25 kA (Ics=100% of Icu), adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/UV/trip alarm contact. MCCB with phase barriers on both sides, insulation withstand capacity 800V, no line-load bias in provided enclosure/panel as per specification no. SW-MCCB |
| 354 | Supplying and erecting SS enclosure of 1.6mm thick with detachable gland platesuitable for upto 100A MCCB. |
| 355 | Supplying and erecting terminal spreaders suitable for 4 pole, upto 100A MCCB (Set of 8) |
| 356 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required |
| 357 | Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. |
| 358 | Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm |
| 359 | Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required |
| 360 | Providing and laying earth connection from earth electrode with 6 SWG dia G.I.Wire in 15 mm dia. G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required. |
| 361 | Supplying, erecting, testing & commissioning of 10 kVA capacity on line puresine wave,PWM,IGBT based UPS with 0.9 to unity output pf ,3 phase input & 3 phase output complete with all protections as per specification no. APUPS(Without batteries) |
| 362 | Supplying and erecting 12 V/65Ah SMF battery with battery terminal wire, duly charged complete with 24 months warranty complete |
| 363 | Supply, Installation, Testing and Commissioning of ongrid Solar Photovoltaic Power Plant conforming to MNRE specifications as amended, consisting of Mono/Poly Crystalline silicon solar cells, net metering facility, necessary protections, earthing, mounted on Aluminium/GI structure of suitable strength with following components complete as required:- a) Solar Photovoltaic Module of capacity 330 Wp or above, manufactured in India, conforming to IS 14286/IEC 61215, IS/IEC 61730-Part-1, IS/IEC 61730-Part-2. Solar Photovoltaic Module conversion efficiency shall not be less than 16.5%. PV modules used in solar power plants/ systems must be warranted for their output peak watt capacity, which should not be less than 90% at the end of 10 years and 80% at the end of 25 years.b) Power Conditioning Unit (PCU) of 350-800 V DC Input voltage range and 400 V AC, three phase, 4 wire, 50Hz +/- 2.5 Hz, output voltage suitable to generate AC Power with efficiency not less than 97%, total harmonic distortion less than 3% and suitable for ambient temperature from 0 to 50 degree C. The PCU shall adjust the voltage and frequency level to suit the Grid Voltage Frequency. c) Data Monitoring System complete with accessories.d) Fixing of Array junction box & Main junction box with IP 65 protection and termination arrangement for incoming and outgoing cable along with glands, lugs and other accessories etc. as required .e) Lightning and surge voltage protection. f) Connections & Interconnections by supplying & fixing required size XLPE insulated copper conductor 1.1 kV grade armoured power and control cables between solar modules, main power cable to grid supply PCU unit along with supplying & fixing of necessary channel/conduit lugs and other accessories etc. as required SOLAR PHOTOVOLTAIC as described above |
| 364 | Design, manufacture supply, installation, testing, commissioning, approvals and handing over in satisfactory working condition of the following Passenger Lifts with Microprocessor based ACVVVF control, Group full collective operation, car enclosure and car / landing doors with stainless steel hairline finish, car floor with PVC finish including provisions for, use by handicapped persons, all controls, accessories, fittings and safety devices (like ARD) and including the cost of providing satisfactory trial operation for 4 weeks after completion and including the cost of providing free comprehensive maintenance for 1 year after handing over complete as per specifications, as required and as below. SITC of Electric Traction Passenger Lift with· Rated capacity :- 8 Passenger/544Kg· Floors :- G+1 floor (2Stops/2 Landings)· Travel :- 3 to 4.2 mtrs· Location of Lift Machine:- MR/MRL· Rated speed :- 1.0mps VS· Car/Landing door clear opening of 800 mm wide x 2000 mm high**Note- Details of item description shall be as per referred Sl.No 17-1-3 of MH SOR (ELE) NOTE: 1: Contactor will submit the GA Drawings of Lift for Approvel from Clint/Consultant before order the Lift. |
| 365 | Design, manufacture supply, installation, testing, commissioning, approvals and handing over in satisfactory working condition of the following Passenger Lifts with Microprocessor based ACVVVF control, Group full collective operation, car enclosure and car / landing doors with stainless steel hairline finish, car floor with PVC finish including provisions for, use by handicapped persons, all controls, accessories, fittings and safety devices (like ARD) and including the cost of providing satisfactory trial operation for 4 weeks after completion and including the cost of providing free comprehensive maintenance for 1 year after handing over complete as per specifications, as required and as below. For Lift having 800 mm wide x 2000mm high clear entrance in 1.5mm thick SS 304 grade solid(non-claded) landing door [Two panel], this includes all necessary accessories like LOP\"s with UP/DN buttons-arrows indicators,extension of guide rails, shaft wiring with trunking, travelling cables, main hoisting ropes/belts, & OSG rope landing doors with all accessories etc. necessary for the normal safe functioning of lift installation complete, NOTE: 1: Contactor will submit the GA Drawings of Lift for Approvel from Clint/Consultant before order the Lift.2: Lift pit depth & overhead etc. will be as per NBC norms. |
| 366 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thickincluding accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required |
| 367 | Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required |
| 368 | Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required |
| 369 | Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet orsurface of wall for lightning conductor complete as required.(For horizontal run) |
| 370 | Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run) |
| 371 | Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required |
| 372 | Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required |
| 373 | Providing and fixing MV. danger notice plate of 200 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required |
| 374 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required 200 mm dia (OD-200 mm & ID-175 mm nominal) |
| 375 | Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall 25mm |
| 376 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required63 mm dia (OD-63 mm & ID-51 mm nominal) |
| 377 | Point Wiring in PVC Conduit, with Modular type Switch: Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with modular type switch, modular plate, suitable size of GI box etc as required. |
| 378 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular plate etc required. |
| 379 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch , connections etc as required. |
| 380 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required 5/6 A switch |
| 381 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required 3 pin 5/6 A socket outlet |
| 382 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required Telephone socket outlet Each |
| 383 | S/F Modular Boxes, base & cover plate: Supplying and fixing following size / modules GI box along with modular base & cover plate for modular switches in recess etc as required. 1 or 2 module (75 mm x 75 mm) |
| 384 | S/F Modular Boxes, base & cover plate: Supplying and fixing following size / modules GI box along with modular base & cover plate for modular switches in recess etc as required. 4/5 module (125 mm x 75 mm ) |
| 385 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc as required.( but without MCB/RCCB/ Isolator). 8 way , Double door |
| 386 | S/F \"C\" series 5A to 32 A MCB: Supplying and fixing 240 volts, \"C\" curve, 10kA miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc, as required. Single Pole |
| 387 | S/F \"C\" series 5A to 32 A MCB: Supplying and fixing 240 volts, \"C\" curve, 10kA miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc, as required. Double Pole |
| 388 | Power Plug Wiring in PVC conduit (2x4 sq. mm): Wiring for light/power plug with 2x4 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit along with 1 number 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required. |
| 389 | Circuit / Sub-main wiring in PVC Conduit: Wiring for circuit / sub-main wiring along with earth wire with the following sizes of PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required. Make-Polycab/ Havells/RK Kabel/KEI 2 X 6 sq. mm + 1X 6 sq. mm earth wire for (for DB) |
| 390 | Circuit / Sub-main wiring in PVC Conduit: Wiring for circuit / sub-main wiring along with earth wire with the following sizes of PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required. Make-Polycab/ Havells/RK Kabel/KEI 2x1.5 Sqmm + 1x1.5 sqmm earth wire (for 5A Socket) |
| 391 | Circuit / Sub-main wiring in PVC Conduit: Wiring for circuit / sub-main wiring along with earth wire with the following sizes of PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required. Make-Polycab/ Havells/RK Kabel/KEI 2x2.5 Sqmm + 1x2.5 sqmm earth wire( for SB)+gate light |
| 392 | S/F Ceiling Rose: Supplying and fixing 2 pin 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required. |
| 393 | Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC , earthing etc. complete as required |
| 394 | EXTERNAL ELECTRICAL WORKS |
| 395 | 11 KV, 1 Panel H.T. Board (Isolator Panel)INCOMING Cum OUTGOING PANEL - 1 No. Supplying, installing, testing and commissioning 11 kV 630A, vacuum circuit breaker with internal arc compliance complete erected on provided CC foundation/MS channels/trench, etc. as per specification no SW-HTS/VCB. |
| 396 | 11KV OUTDOOR UNITISED SUB-STATION (PSS TYPE) HT Switchgear Supplying, installing, testing & commissioning compact substation with 3 phase, 11/0.433 kV, 50 Hz., 400 kVA, Mineral oil immersed Copper wound, without gas cushioning, hermetically Sealed transformer having indoortype transformer bushings, with HT side (Incoming side) Circuit Breaker of appropriate rating & capacity and LT side (outgoing side) MCCBs (4 pole) of appropriate capacity, with inbuilt metering cubical having 3 epoxy coated CT\"s with CT Ratio 630/5 A, 10 or 15VA Burden, 0.5S Accuracy Class & 3 epoxy coated PT\"s with PT Ratio 11/0.110KV, 10 or 15 VA Burden, 0.5S Accuracy Class properly arranged in standard MSEDCL approved enclosure, using type A winding insulation (kraft paper),standard accessories complete with test certificate with losses below 1225 Watts at 50% load, 3450 Watts at 100% load for transformer, as per IS:1180 (part 1) : 2014, with necessary permissions of Electrical Inspector, as per specification no SS-TR-CS |
| 397 | Supplying of the following sizes of 11 KV Alum. (E), Armoured XLPE HT power cable as per IS7098(part-2)-1985 amended uptodate, as per specifications.Supplying , erecting & terminating XLPE insulated, galvanised steel formedwire armoured (strip) cable 11 kV(E), 3 x 240 sq. mm. aluminium conductorlaid in provided trench / pipe as per specification no. CB-HT |
| 398 | Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required:240 sq. mm |
| 399 | Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required:240 sq. mm |
| 400 | CAPACITOR PANEL_125 Kvar, Supplying, erecting, testing & commisioning 125 kVAr, 440 V, 3 phase, 50 Hz.,APFC Panel with contactor logic with intelligent microprocessor relay,consisting of 2,3,5,5,10,20,20,20,20,20 or suitable steps of APP/MPP typecapacitor units with detuned (harmonic filter) reactors of suitable rating, APFCpanel shall be compliance to IEC 61439 and power quality IEC 61921 standard as per specification no. CP-ED/APFC. |
| 401 | Supplying of XLPE/PVC insulated sheathed (Heavy duty) armoured electric cable with aluminium conductor. Supplying, erecting & terminating FR XLPE insulated, galvanised steelformed wire armoured (strip) cable, 1100 V 3½ core 240 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid inprovided trench/ pipe as per specification no. CB-LT/AL |
| 402 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable, 1100 V 3½ core 150 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL |
| 403 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable, 1100 V 3½ core 120 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per pecification no. CB-LT/AL |
| 404 | Supplying, erecting & terminating FR XLPE insulated, galvanised steelformed wire armoured (strip) cable, 1100 V 3½ core 95 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL |
| 405 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable, 1100 V 3½ core 50 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL |
| 406 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable, 1100 V 3½ core 25 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL |
| 407 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel wire armoured (round) cable, 1100 V 4 core 16 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL |
| 408 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel wire armoured (round) cable, 1100 V 4 core 6 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL |
| 409 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel wire armoured (round) cable, 1100 V 2 core 6 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL |
| 410 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required200 mm dia (OD-200 mm & ID-175 mm nominal) |
| 411 | Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.450 mm width X 62.5 mm depth X 2.0 mm thickness |
| 412 | Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.150 mm width X 50 mm depth X 1.6 mm thickness |
| 413 | Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray \"bends\" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended fromthe ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.450 mm width X 62.5 mm depth X 2.0 mm thickness |
| 414 | Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray \"bends\" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended fromthe ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.150 mm width X 50 mm depth X 1.6 mm thickness |
| 415 | EARTHING SYSTEM. Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thickincluding accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required |
| 416 | Supplying and laying 25 mm X 5 mm G.I. strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) |
| 417 | Earthing with copper earth plate 600 mm X 600 mm X 3 mm thickincluding accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required |
| 418 | Supplying and laying 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and fe-filling etc. as required. |
| 419 | Lighting poleSupply and erection of 7 metre height Hot-dip galvanized octagonal street light pole with following arm with top dia 70 mm and bottom dia A/F 155 mm, made of 3 mm thick sheet along with base plate of size 260 X 260 X 16 mm , small door opening for junction box mounting with MCB & connector with 2.5 sq mm copper wires, cement concrete of 1:3:6 including excavation, refilling and suitable size foundation bolts with template and all complete job as required.(Note- Foundation work from Civil BOQ items)Providing & erecting 7 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 130 mm A/F, top 70 mm A/F on providedfoundation as per specification no. OH-PL/OPL |
| 420 | Lighting poleSupply and erection of 7 metre height Hot-dip galvanized octagonal street light pole with following arm with top dia 70 mm and bottom dia A/F 155 mm, made of 3 mm thick sheet along with base plate of size 260 X 260 X 16 mm , small door opening for junction box mounting with MCB & connector with 2.5 sq mm copper wires, cement concrete of 1:3:6 including excavation, refilling and suitable size foundation bolts with template and all complete job as required.(Note- Foundation work from Civil BOQ items)Providing and erecting galvanised 1000mm single arm sword type bracket withFRP dome and ball as per specification no. OH-PL/BKT |
| 421 | Lighting poleSupply and erection of 7 metre height Hot-dip galvanized octagonal street light pole with following arm with top dia 70 mm and bottom dia A/F 155 mm, made of 3 mm thick sheet along with base plate of size 260 X 260 X 16 mm , small door opening for junction box mounting with MCB & connector with 2.5 sq mm copper wires, cement concrete of 1:3:6 including excavation, refilling and suitable size foundation bolts with template and all complete job as required.(Note- Foundation work from Civil BOQ items)Providing and erecting galvanised 1000mm double arm sword type bracketwith FRP dome and ball as per specification no. OH-PL/BKT |
| 422 | Supplying and erecting integrated LED street light fitting 60W IP65 & IK08 class having single piece pressure die-cast aluminium housing, having system lumens output of Min. 6600 Lumens, min. efficacy of 110 lumen/W, CRI>70, CCT upto 6500K, THD<10%, p.f. >0.95, operating range of 140-270V, inbuilt surge protection of 10 kV, Life class of 50,000 Hrs at L70B50 including driver complete with minimum 2 Years warranty as per specification No. FG-ODF/SL. |
| 423 | Supplying and erecting integrated LED flood light fitting Max. 100W IP65 & IK07 class having pressure die-cast aluminium housing, having system lumens output of Min. 12000 Lumens, min. efficacy of 120 lumen/W, CRI>70, CCT upto 6500K, THD<10%, p.f. >0.90, operating range of 140-270V, inbuilt surge protection of 4 kV, Life class of 50,000 Hrs at L70B50 including driver with Ushaped bracket with minimum 2 Years warranty as per specification No. FGODF/FL. |
| 424 | HIGH MAST, Supplying and erecting 20 m (clear height) motorized high-mast (Top-150mm, Bottom-410 mm) hot dipped galvanized material with average minimum thickness 65 micron, made from high tensile structure grade steel as per BSEN -10025 S 355/E350 & 3+3 mm thickness, with base plate 25 mm thick x OD 570 mm grade as per IS-2062, pole made in signal section & submerge arc welded, with lowering & raising motorized unit, wire rope stainless steel 316 grade 2 nos., 7x19 construction 6 mm, SG-DG U clamps, double drum winch assembly 500 kg, 5x2.5 sq.mm flexible copper cable with lantern carriage assembly suitable for max. 16 nos. luminaries and its control gear box, lightning arrestor, arrangement for fixing aviation light, night glow reflector on pole at suitable height, high- mast with serial number, factory inspection report/test report of high-mast should be provided as per specifications on provided foundation J type stud/bolts with double check nuts & necessary accessories complete. specification no. OHPL/HM |
| 425 | Supplying and erecting outdoor stand mounted feeder pillar for high-mast of the same manufacturer with 32A TPN MCB incomer, 24hr astronomical time switch with minimum 5 years battery backup, 25 A TP contactor for automatic switching of luminaries, 2 no. 9A contactors and raise/lower push button, and provision for termination of adequate size of incoming and outgoing cables complete erected in min. 14 SWG CRCA sheet box with supporting angles, self lock, gasket and slanting top erected on CC foundation complete |
| 426 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel wire rrmoured (round) cable, 1100 V 2 core 6 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL |
| 427 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor2 x 6 Sq.mm (19mm) |
| 428 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ metal pipe as required.Upto 35 sq. mm |
| 429 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required.63 mm dia (OD-63 mm & ID-51 mm nominal) |
| 430 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thickincluding accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required |
| 431 | Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required |
| 432 | Supplying and laying 25 mm X 5 mm G.I. strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) |
| 433 | Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. |
| 434 | DG SET WITH AMF PANEL, Supplying, erecting, testing and commissioning of diesel generating set with alternator of 160 kVA output continuous rating, 3 phase, 415 V, 50 Hz, 0.8 p.f., A.C. supply, a totally enclosed air cooled / liquid cooled multi-cylinder diesel engine developing suitable BHP at 1500 rpm with 10% overload for 1 hour in 12 hours, along with standard accessories, self-excited, self-regulated, screen protected alternator with static excitation system running at 1500 RPM as per IS 4722-2001 with voltage regulation +/- 5 %, with performance class G2/G3 and maximum fuel consumption 27.8 ltr/hr @75% loading. Both the engine and alternator direct coupled on a common fabricated steel base frame and mounted on anti-vibrating pads, with standard control panel comprising meters,switchgears, indicators connected with suitable wires/cables, the complete set enclosed in composite acoustic enclosure as fully assembled integral unit made of 16 SWG CRCA sheet, sound absorbing material to restrict sound level up to 75dB at 1.0 m, provided with first filling of oil, diesel not less than 290 ltr etc., on provided M20 grade CC foundation as per specification no. GEN-DG |
| 435 | Supplying, erecting, testing and commissioning of microprocessor based AMF panel suitable for diesel generating set of above 140 kVA upto 180 kVA capacity 3 phase, 415 V, 50 Hz, A.C. supply with all standard features, safeties etc as per specification no. GEN-AMF |
| 436 | Providing and fixing MV. danger notice plate of 200 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required |
| 437 | Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required |
| 438 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required200 mm dia (OD-200 mm & ID-175 mm nominal) |
| 439 | CCTV Items |
| 440 | Supplying and installing PBT loose tube HDPE sheathed armoured single mode optical fiber cable with 6 fiber, core dia 9/125μm (OS1/OS2) 10 GBPS speed compliant to IEC 60793/IEC 60794 standards in provided pipe/trench complete. |
| 441 | Supplying and fixing 12 ports light guide unloaded interconnect unit, rack mounted type, with adapter panel for termination of optical fiber cables in provided U rack complete as per specification no. WG-NAS/ LIU |
| 442 | Supplying and installing FR PVC sheathed Aluminum foiled wrapped over all tinned copper braided HDPE insulated copper cat-6 STP cable suitable for networking compliant with ANSI/TIA-568.2-D standards in provided conduit/casing-n-capping as per specification no. WG-ELVC/NC |
| 443 | Supplying and fixing tool-less IO (ethernet) flush/surface type in providedmodular box as per specification no. WG-NAS/IO |
| 444 | Supplying and fixing Cat 6, 24 port patch panel with keystone jacks compliant with ANSI/TIA/EIA 568.C.2 & ISO/IEC 11810 complete as per specification no. WG-NAS/PP |
| 445 | Supplying and fixing 1 m 24 AWG multi stranded UTP patch cord with RJ-45 factory crimped connector of Cat 6 type, compliant ANSI/TIA-568.2-D standards in position as per specification no. WG-ELVC/PC |
| 446 | Supplying and fixing 2 m 24 AWG multi stranded UTP patch cord with RJ-45factory crimped connector of cat 6 type compliant ANSI/TIA-568.2-D standards in position as per specification no. WG-ELVC/PC |
| 447 | Supplying & erecting approved make High definition 4/5 Megapixel IP IR Varifocal Dome Camera with following features Image Sensor : minimum 1/2.8\" Progressive Scan CMOS, Video Resolution: minimum 2592 x 1520 Video Compression : H.264, H.265 or higher, at least Three individually configurable stream,Frame Rate : minimum 25 fps at all resolutions WDR : minimum 120 dB Wide Dynamic Range, ONVIF profile Conformant.minimum IR distance : 50m,Lens Type: 2.8 - 13mm Lens, auto/motorized varifocal focal, Field of View : horizontal FOV 103° to 32°, vertical FOV 73° to 24°, diagonal FOV 142° to 40° Lux sensitivity - minimum 0.2 Lux at color, minimum 0.05 Lux at Black & White,0.0 Lux (IR) Night Vision Distance Min IR- 30m, Camera minimum Adjustment Angles - Pan : 350°, Tilt : 72°, Rotate : 350°. Power Supply : Support 12VDC & PoE,IP67/IP66, IK10,built in micro SD/SDHC/SDXC card slot of min 128 GB,built in microphone.minimum Input/Output - Audio in × 1, Audio Out × 1, Alarm in× 1, Alarm Out × 1. Image Settings : Rotate mode, saturation, brightness, contrast, sharpness, gain,white balance. Image Enhancements : Day/Night-Auto (ICR)/Color/Black & White, 3D Digital Noise Reduction, Automatic White Balance, Automatic Gain Control, Backlight Compensation, Highlight Compensation. Events : Privacy Masking, Motion detection, Scene change detection, Face capture, Video tampering, audio exception detection, Region entrance detection, Region exiting detection. Operating temperature (-30 to 60° C) .Security - User account and password protection, HTTPS, IP filter, IEEE 802.1X, digest authentication, user access log, TLS1.2, AES-256, SSH/Telnet closed, FTP disabled. Protocol - DHCP, UDP, HTTP, HTTPS, NTP, DNS, RTP, RTSP, SMTP, SSL/TLS, TCP/IP, Secure Real-Time Transport Protocol (SRTP),Bonjour, SNMP and Secure shell (SSH) supported protocol. RoHS, WEEE, ISO-14001 and REACH compliant, UL/EN OR equivalent BIS/TECH/STQC or any indian standards as applicable, CE, FCC certified. duly erected in position on wall/ceiling/false ceiling/provided pole (mounting height not more than 5 meter) etc with all accessories etc complete as per specification no. CCTV-CAM. |
| 448 | Supplying & erecting of High definition 4/5 Megapixel IP IR varifocal Bullet Camera with following features Image Sensor : minimum 1/ 2.8\" Progressive Scan CMOS, Video Resolution : minimum 2592 x 1520 Video compression : H.264, H.265 or higher, at least Three individually configurable stream,Frame Rate : minimum 25 fps at all resolutions.WDR : minimum 120 dB Wide Dynamic Range,ONVIF profile conformant,minimum IR distance : 50m,Lens Type: 2.8 - 13mm Lens, auto/motorized varifocal focal,Field of View : horizontal FOV 103° to 32°, vertical FOV 73° to 24°, diagonal FOV 142° to 40° Lux sensitivity - minimum 0.2 Lux at color, minimum 0.05 Lux at Black & White,0.0 Lux (IR) Night Vision Distance Min IR- 50m, Camera minimum Adjustment Angles - Pan : 350°, Tilt : 72°, Rotate : 350°.Power Supply : Support 12VDC & PoE,IP67, IK10 – Vandal Resistant,built in micro SD/SDHC/SDXC card slot of min 128 GB,built in microphone.minimum Input/Output- Audio in × 1, Audio Out × 1 , Alarm in× 1, Alarm Out × 1. Image Settings: Rotate mode, saturation, brightness, contrast, sharpness, gain,white balance.Image Enhancements: Day/ Night-Auto (ICR)/Color/Black & White, 3D Digital Noise Reduction, Automatic White Balance, Automatic Gain Control, BacklightCompensation, Highlight Compensation. Events: Privacy Masking, Motion detection, Scene change detection, Face capture, Video tampering, audio exception detection, Region entrance detection, Region exiting detection.Operating temperature ( -30 to 60° C ) .Security- User account and password protection, HTTPS, IP filter, IEEE 802.1X,digest authentication, user access log, TLS1.2, AES-256, SSH/Telnet closed, FTPdisabled.Protocol - DHCP, UDP, HTTP, HTTPS, NTP, DNS, RTP, RTSP, SMTP,SSL/TLS, TCP/IP, Secure Real-Time Transport Protocol (SRTP), Bonjour,SNMP and Secure shell (SSH) supported protocol. RoHS, WEEE, ISO-14001 and REACH compliant, UL/EN OR equivalent BIS/TECH/STQC or any indian standards as applicable, CE, FCC certified. duly erected in position on wall/ceiling/false ceiling/provided pole (mounting height not more than 5 meter) etc with all accessories etc complete as per specification no. CCTV-CAM. |
| 449 | Supplying & erecting of High definition 4/5 Megapixel IP IR PTZ Camera with following features Image Sensor : minimum 1/2.8\" Progressive Scan CMOS Video Resolution: minimum 2880 x 1620 Video Compression : H.264, H.265 or higher, at least Three individually configurable stream, Frame Rate : minimum 30 fps at all resolutions, WDR : minimum 120 dB Wide Dynamic Range, ONVIF profile conformant.Auto Tracking, Pre-set Tour Settings, Pan : 360° endless, Tilt : From -15° to 90° (auto-flip 180°), minimum Pan Speed - from 0.1°/s to 160°/s, minimum Preset Speed: 240°/s, minimum Tilt Speed - from 0.1°/s to 120°/s, minimum Preset Speed : 200°/s, Min Presets- 250, Min IR distance :150m, Lens Type : minimum 4.3 - 12.5mm Lens min 16 x digital zoom, min 30 x optical Zoom. Focus Mode : Auto/Zooming/One Push Manual, Lux sensitivity- minimum 0.2 Lux at color, minimum 0.05 Lux at Black & White, 0.0 Lux (IR) Night Vision Distance Min IR- 150m, Power Supply : support 12/24 VDC, 24 VAC & PoE, IP67/IP66, IK10, built in micro SD/SDHC/SDXC card slot minimum 256 GB, built in microphone. minimum Input/Output : Audio in × 1, Audio Out × 1, Alarm in× 1, Alarm Out × 1. Image Settings : Rotate mode, saturation, brightness, contrast, sharpness, gain, white balance. Image Enhancements : Day/Night-Auto CR)/Color/Black & White, 3D Digital Noise Reduction, Automatic White Balance, Automatic Gain Control, Backlight Compensation, Highlight Compensation. Events : Privacy Masking, Motion detection, Scene change detection, Face capture, Video tampering, audio exception detection, Region entrance detection, Region exiting detection. Operating temperature ( -30 to 60° C ) .Security : User account and password protection, HTTPS, IP filter, IEEE 802.1X, digest authentication, user access log, TLS1.2, AES-256, SSH/Telnet closed, FTP disabled. Protocol-DHCP, UDP, HTTP, HTTPS, NTP, DNS, RTP, RTSP, SMTP, SSL/TLS, TCP/IP, Secure Real-Time Transport Protocol (SRTP),Bonjour,SNMP and Secure shell (SSH) supported protocol.RoHS, WEEE, ISO-14001 and REACH compliant, UL/EN OR equivalent BIS/TECH/STQC or any indian standards as applicable, CE, FCC certified.duly erected in position on wall/ceiling/false ceiling/provided pole (mounting height not more than 5 meter) etc with all accessories etc complete as per specification no CCTV-CAM. |
| 450 | Supplying, installing, testing & commissioning of 64/80 Ch Network Video Recorder (NVR), suitable connect Min. 64 IP Cameras, up to 5 Megapixel Resolution, with HDMI 1/VGA 1 and HDMI 2/VGA 2 outputs provided, Atleast one HDMI output of 4K resolution, atleast one VGA output with output up to 1920 × 1080, Support H.265 or higher, H.264, MJPEG, Supports Redundant Dual Power, Incoming Bandwidth 320 Mbps with minimum 8 SATA Hard Disks, ANR Technology, 8 SATA interfaces for 8 HDDs and capacity of each HDD up to 8TB,minimum 02 USB port, Alarm I/O 16/4, RJ-45 10/100/ 1000 Mbps selfadaptive Ethernet interface, support multi brand network Cameras, ONVIF conformance, Multiple network monitoring: Web viewer .support protocol TCP/IP, DHCP, DNS, DDNS, NTP, SADP, SMTP, NFS,iSCSI, UPnP™, HTTPS. RoHS, UL, CE, FCC certified. duly erected in provided U Rack with wiring connections, tagging and programming etc. complete as per specificationss no. CCTV-NVR. |
| 451 | Supply, installation, testing and commissioning of Joystick with 5\" LCD Display. Approved Makes :Allgovision/ Impulse / Mobotix / Cisco/ Axis |
| 452 | Supplying & erecting 8 TB internal Surveillance HDD suitable for SATA Port of NVR, interface transfer rate 6 GB/S, maximum sustained transfer rate 210MB/Sec to 213 MB/S. Drive bay supported 08+, Cameras supported up to 64,Cache (MB) 256, Load/Unload Cycle -3000000, Work Load Rating per Year 180TB, MTBF 1000000 Hrs. HTTPS. RoHS, UL, CE certified, duly erected in position in provided NVR as per specification no. CCTV-HDD |
| 453 | Supplying & erecting 55\" professional LED display with 1920 *1080 ( Full HD) Display, suitable for 32/64 channel NVR and following features Brightness: minimum 500 Cd/m2 Contrast Ratio: minimum 1000:1Viewing angle: 178/178 deg. Response time: maximum 8 ms Inputs: HDMI, VGA, BNC,USB, Audio In, Built-in speakers maximum 10 W, Suitable to operate on 100-240 V 50 Hz AC supply and 24/7 Duty Cycle duly erected on wall or table top with standard accessories like wall mount stand and wiring connections etc. complete as per specifications no. CCTV-MON |
| 454 | Supplying and fixing 9U Hybrid IP66 outdoor mount server rack with pole mount bracket (Dimension- DxWxH - 500x550x450 mm) as per specification no. WG-NAS/RAK |
| 455 | Supplying, fixing, and configuring 24G PoE ports with 2X10G RJ-45 & 4X10G SFP+ & support stacking , VRRP,OSPF,policy based routing managed layer 2+ PoE switch compliant with IEEE 802.3 standards erected in provided rack completes |
| 456 | Supplying, fixing, and configuring 8-ports managed gigabit, layer-2 switch, 10/100/1000 base-T, PoE smart switch plus 2 SFP erected in provided rack compliant with IEEE 802.3 standards complete. |
| 457 | Providing & erecting 6 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 130 mm A/F, top 70 mm A/F on provided foundation as per specification no. OH-PL/OPL |
| 458 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm |
| 459 | Fire Fighting Sytsem |
| 460 | (A) FIRE WATER PUMPING SYSTEM Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required: (B) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. (C) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-\"F\" insulation, conforming to IS-325. (D) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required.(E) Suitable cement concrete foundation duly plastered with anti vibration pads.1620 Ipm at 70 m Head |
| 461 | A) Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Diesel Driven Pump) (B) Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520.(C) Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12/24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required.(D) M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required.(E) Suitable cement concrete foundation duly plastered and with anti vibration pads.2280 Ipm at 70 m Head |
| 462 | (A) Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Jockey Pump)(B) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS: 1520.(C) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-\"F\" insulation, conforming to IS: 325.(D) M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required.(E) Suitable cement concrete foundation duly plastered and with anti vibration pads.180 Ipm at 70 m Head |
| 463 | Fabrication, Supplying, Installation, Testing & Commissioning of Electrical Control Panel of cubical construction ,floor mounted type, fabricated out of 2mm. thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection with suitable size copper conductor cable/solid copper strip ,having switchgears and accessories, mounting and internal wiring, earth terminals, numbering etc. complete in all respects, suitable for main fire pump,pressurisation pump & diesel pump set complete as per CPWD specification with following in coming and outgoings, suitable for operation on 415 V, 3 phase 50 HZ AC supply with enclosure protection class IP 42. INCOMING 250A, 50kA 4 Pole MCCB, lcs=100% Icu rating Digital Voltmeter 0-500V with selector switch Digital Ammeter (0-250 A) with selector swtich & CTs etc. LED type RYB phase indicating lamps ,ON,OFF,trip indicating lamps Set of Copper Bus Bar 300A OUTGOING (Note : All outgoing feeders for pumps should have digital Ammeter with selector switches,and LED type ON,OFF, trip indicating lamps) MAIN FIRE PUMP 125 A, 50kA TPN and MCCB, Ics=100% Icu, with fully automatic Star/Delta starter suitable for 60 HP pump with overload protection, current sensing type single phase preventor complete with all acceessories and internal wiring required for automatic operation, selector switch for local/remote, auto/manual/OFF operation. JOCKEY PUMP 63 A, 50kA TPN MCCB, Ics=100% Icu, with suitable HP fully automatic Star/Delta starter with overload protection, current sensing type single phase preventor complete with all acceessories and internal wiring required for automatic operation, selector switch for local/remote, auto/manual/OFF operation. DIESEL ENGINE CONTROL Control for diesel engine comprising – Automatic/Manual selctor switch & 3 attempts starting device, timers and relays as required, push buttons, start/stop in manual mode Indicating lamp for high/ Low Lub. Oil pressure, High Water Temp and Engine on indication Battery charger suitbale for 12V/24 V DC with boost and trickle selector switch, 0-30 V DC volt meter, and 0-20 A DC Ammeter. All standard relays and accessories for automatic operation of diesel engine SYSTEM CONTROLLER Designing, Supply, Installation, Testing and commissioning of system controller to control operation of main electric fire pump, diesel pump, Pressurization pump, Terrace pump in sequence as per specification consisting of relays, timers. Sensors, annunciation window for fault indication, complete as per specification |
| 464 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. As required.314 X 95 sq. mm (45mm) |
| 465 | 3 X 10 sq. mm (22mm) |
| 466 | Supplying and drawing following sizes of FRLS PVC insulatedcopper conductor, single core cable in the existing surface/recessed steel/ PVC condui2 × 1.5 sq. mm |
| 467 | Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17,5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.100 W × 50 D × 1.6 T mm GI Cable Tray |
| 468 | Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17,5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.150 W × 50 D × 1.6 T mm GI Cable Tray |
| 469 | Upto 35 sq. mm (clamped with 1mm thick saddle) |
| 470 | Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp) |
| 471 | Providing and fixing 6 SWG dia G.l. wire on surface or in recess forloop earthing as required. |
| 472 | Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required. |
| 473 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 4X 10 sq. mm + 2 X 6 sq. mm earth wire |
| 474 | Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metalseat,ISI marked complete with nuts,bolts washers,gaskets and conforming to IS 780 of following sizes as required. 50 mm dia |
| 475 | Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metalseat,ISI marked complete with nuts,bolts washers,gaskets and conforming to IS 780 of following sizes as required. 100mm dia |
| 476 | Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metalseat,ISI marked complete with nuts,bolts washers,gaskets and conforming to IS 780 of following sizes as required. 150mm dia |
| 477 | Providing installation, testing and commissioning of swinging non return valve of following sizes conforming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required: 50 mm diameter |
| 478 | Providing installation, testing and commissioning of swinging non return valve of following sizes conforming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required: 100 mm diameter |
| 479 | Providing installation, testing and commissioning of swinging non return valve of following sizes conforming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required: 150 mm diameter |
| 480 | Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required. |
| 481 | Providing,laying,testing & commissioning of ERW MS pipe C Class(Heavy) conforming to IS 1239/3589 i/c including welding, fittings like elbows,tees,flanges ,tapers,nuts bolts,gaskets etc and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required 200 mm diameter |
| 482 | Providing,laying,testing & commissioning of ERW MS pipe C Class(Heavy) conforming to IS 1239/3589 i/c including welding, fittings like elbows,tees,flanges ,tapers,nuts bolts,gaskets etc and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required 150 mm diameter |
| 483 | Providing,laying,testing & commissioning of ERW MS pipe C Class(Heavy) conforming to IS 1239/3589 i/c including welding, fittings like elbows,tees,flanges ,tapers,nuts bolts,gaskets etc and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required 100 mm diameter |
| 484 | Providing,laying,testing & commissioning of ERW MS pipe C Class(Heavy) conforming to IS 1239/3589 i/c including welding, fittings like elbows,tees,flanges ,tapers,nuts bolts,gaskets etc and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required 80 mm diameter |
| 485 | Providing,laying,testing & commissioning of ERW MS pipe C Class(Heavy) conforming to IS 1239/3589 i/c including welding, fittings like elbows,tees,flanges ,tapers,nuts bolts,gaskets etc and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required 50 mm diameter |
| 486 | HYDRANT SYSTEM Providing, laying, testing & commissioning of \"C\" class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 150 mm diameter |
| 487 | HYDRANT SYSTEM Providing, laying, testing & commissioning of \"C\" class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 80 mm diameter |
| 488 | Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metalseat,ISI marked complete with nuts,bolts washers,gaskets and conforming to IS 780 of following sizes as required. 150 NB |
| 489 | Providing and fixing,testing and commissioning of butterfly valve of PN 1.6 rating complete with nuts,bolts washers,gaskets conorming to BS - 5155 IS 13095 fo following sizes as required: 150NB |
| 490 | Providing installation, testing and commissioning of swinging non return valve of following sizes conforming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required: 150 NB |
| 491 | Supplying & fixing single headed internal hydrant valve with instantanous stainless steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290(type-A) with blank Gunmetal/stainless steel cap and chain as required: *Single headed |
| 492 | Supplying and fixing first-Aid Hose Reel with MS construction spray painted in post office red,conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hosethermo plastic(textile reinforced)type-2 as IS:12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipments on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe aand socket. 40 m |
| 493 | Supplying and fixing 63mm dia, 15m long RRL hose pipe with 63mm dia male and femalecouplings duly bound with GI wires, rivetsetc. Conforming to IS 636(type-2) as required:SS |
| 494 | Supplying and fixing 63mm dia, SS metal short branch pipe with 20mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :SS |
| 495 | Supplying, fixing,of fire brigade collecting of cast iron body with SS metal male instantaneous inlet couplings complete with cap and chain as reqd.for suitable dia MS pipe connection conforming to IS 904 as required.For fire riser *4 way-150 mm dia |
| 496 | Providing, laying, testing & commissioning of \"C\" class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 150 mm diameter |
| 497 | Providing, laying, testing & commissioning of \"C\" class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 100 mm diameter |
| 498 | Providing, laying, testing & commissioning of \"C\" class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 80 mm diameter |
| 499 | Providing, laying, testing & commissioning of \"C\" class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 65 mm diameter |
| 500 | Providing, laying, testing & commissioning of \"C\" class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :50 mm diameter |
| 501 | Providing, laying, testing & commissioning of \"C\" class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 40 mm diameter |
| 502 | Providing, laying, testing & commissioning of \"C\" class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 32 mm diameter |
| 503 | Providing, laying, testing & commissioning of \"C\" class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 25 mm diameter |
| 504 | Providing and fixing,testing and commissioning of butterfly valve of PN 1.6 rating complete with nuts,bolts washers,gaskets conorming to BS - 5155 IS 13095 fo following sizes as required: 100 mm diameter |
| 505 | Providing, fixing, testing & commissioning of 15mm dia uartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Pendent Sprinkler |
| 506 | Providing, fixing, testing & commissioning of 15mm dia uartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Upright Sprinkler |
| 507 | Providing, fixing, testing & commissioning of 15mm dia uartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Side wall sprinkler |
| 508 | Providing,installation,testing & commissioning of adjustable rosette plate for 15mm dia in white finish UL listed or FM approved complete as required |
| 509 | Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPTmale thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete asrequired.: 1000 mm |
| 510 | Supply ,installation ,testing & commissioning of Double flanged Isolation control valve with complete set.(150 mm NB) |
| 511 | Supply ,installation ,testing & commissioning of electrically operated water Flow switches.(100 mm)Paddle type. |
| 512 | Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metalseat,ISI marked complete with nuts,bolts washers,gaskets and conforming to IS 780 of following sizes as required. 100 NB |
| 513 | Fire Detection and Alarm system Supplying, installation, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the following loop modules and capable of supporting not less than 240 devices (including detectors) and minimum 120 detectors per loop and loop length up to 2 km, network communication card, minimum 320 character graphics/ LCD display with touch screen or other keypad and minimum 4000 events history log in the non volatile memory (EPROM), power supply unit (230 ± 5% V, 50 hz), 48 hrs back-up with 24 volt sealed maintenance free batteries with automatic charger. The panel shall have facility to connect printer to printout log and facility to have seamless integration with analog/digital voice evacuation system (which is part of the schedule of work under SH: PA System) and shall be complete with all accessories . The panel shall be compatible for IBMS system with open protocol BACnet/ Modbus over IP complete as per specificationsTwo Loop Panel. |
| 514 | Supplying, installation, testing & commissioning of repeater panel wih 320 character/ Touch screen LCD display with inbuilt |
| 515 | Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required. |
| 516 | Supplying, installation, testing & commissioning of addressable manual call point complete as required |
| 517 | Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required. |
| 518 | Addressable Control Moudle |
| 519 | Supply,Installation,Testing and Commissioning of 2C x 1.5 Sq. mm PVC Insulated Multistrand Copper FRLS Armoured Cable |
| 520 | PROVIDING AND FIXIG CERAMIC ESSCO JAQUAR STELLA RINLESS WALL HUNG WC OF APPROVED QUALITY: |
| 521 | Providing and fixing Ceramic Jaquar Wash Table Basin of approved quality: |
| 522 | Providing and fixing White Ceramic Jaquar URS-WHT-13253O Urinal, For Bathroomk of approved quality: |
| 523 | Providing and fixing CP brass wall mixer 3 -in-1 system with necessary wall flanges complete all. of quality & make as approved by Engineer in charge. |
| 524 | Providing and fixing This Bottle Trap 32mm Size with 190mm Long Wall Connection P Flange. (chrome finish) of approved quality: |
| 525 | Providing and fixing Jaquar Clarion Swan Neck Tap of approved quality: |
| 526 | Providing and fixing Jaquar Health Brass HEALTH Faucetof approved quality: |
| 527 | Providing and fixing Jaquar LONG BODY BIB COCK of approved quality: 15 mm nominal bore |
| 528 | Providing and fixing SANYA Ss Sandwich R Shower, For Bathroom, Dimension/Size: 12x12 of approved quality: 15 mm nominal bore |
| 529 | Providing & Fixing CPVC consealed valve as per ISO:138 / IS-7834 for the operating temperature upto 60 Deg.C threaded type( Inside Bathroom )25 mm nominal bore |
| 530 | Providing and fixing soil, waste and vent SWR pipes Supply fixing and testing UPVC SWR pipe confirming to IS:13592 for waste connection from wash basin and pantry sink to floor trap or thermosyphonage pipe with solvent cement joints including all the fittings laid above the fall ceilling connected in wall etc the shall include wall chiseling making good the same in cement mortar etc complete include with all necessary support like GI hangers support GI grip and bolts GI clamp etc in fall ceilling area as well as supplying and fixing GI slotted angle iron bracket hangers supports with necessary drilling holes to suit the insertion of pipe clamps deburring brick work concrete supports etc as per detailed drawing for supporting soil waste and rain water pipes and water supply pipes in shaft with suitable GI clamps GI bolts anchor nuts and washers fixede on shaft walls outer walls etc. 110mm dia |
| 531 | Supply fixing and testing UPVC SWR pipe confirming to IS:13592 (Type - B) for waste connection from wash basin and pantry sink to floor trap or thermosyphonage pipe with solvent cement joints including all the fittings laid above the fall ceilling connected in wall etc the shall include wall chiseling making good the same in cement mortar etc complete include with all necessary support like GI hangers support GI grip and bolts GI clamp etc in fall ceilling area as well as supplying and fixing GI slotted angle iron bracket hangers supports with necessary drilling holes to suit the insertion of pipe clamps deburring brick work concrete supports etc as per detailed drawing for supporting soil waste and rain water pipes and water supply pipes in shaft with suitable GI clamps GI bolts anchor nuts and washers fixede on shaft walls outer walls etc. 40mm dia |
| 532 | Providing and fixing PVC clamps for UPVC SWR pipes of diameter :110mm dia pipe |
| 533 | Providing fixing and testing UPVC SWR plain ring type 90 Deg Bend IS:14735110 mm dia |
| 534 | Providing fixing and testing UPVC SWR plain ring type 45 Deg Bend IS: HSN CODE : 39172390110 mm dia |
| 535 | Providing fixing and testing UPVC SWR plain Single Y Branch Door type fitting IS:HSN CODE : 39172390110 mm dia |
| 536 | Providing fixing and testing UPVC SWR plain Reducing Double Y Branch Door type fitting 110 x 75 mm dia |
| 537 | Providing and fixing and testing UPVC Multi floor trap with SS grating with all necessary UPVC pipes connection extension pipe and reducing tee for wate pipe connections from tiolet and wash area.all floor trap should be 70mm water seal .110 x 75mm Dia |
| 538 | Providing and Fixing uPVC Balcony drain with jali of following size inlet and outlet including cutting and making good the walls and floors wherever required complete in all respects. 75mm dia |
| 539 | Providing and fixing 125 mm dia, 3 mm thick Stainless steel grating with frame for floor traps or drains of required pattern including cutting and making good the floors complete.125mm dia. |
| 540 | SPECTATORS GALLERY (Plumbing and saniation) |
| 541 | Providing and fixing Ceramic Essco Jaquar stella rimless wall hung wc of approved quality: |
| 542 | Providing and fixing White Ceramic Jaquar URS-WHT-13253O Urinal, For Bathroomk of approved quality: |
| 543 | Providing and fixing Ceramic Jaquar Wash Table Basin of approved quality: |
| 544 | Providing and fixing This Bottle Trap 32mm Size with 190mm Long Wall Connection P Flange. (chrome finish) of approved quality: |
| 545 | Providing and fixing SS Jaquar FLR CHR 5041 2 Way Bib Cock of approved quality: |
| 546 | Providing and fixing Jaquar Health Brass HEALTH Faucetof approved quality: |
| 547 | Providing and fixing SANYA Ss Sandwich R Shower, For Bathroom, Dimension/Size: 12x12 of approved quality: 15 mm nominal bore |
| 548 | PROPOSED BADMINTON COURT PLUMBING ( Plumbing and sanitation) |
| 549 | PROVIDING AND FIXIG CERAMIC ESSCO JAQUAR STELLA RINLESS WALL HUNG WC OF APPROVED QUALITY: |
| 550 | PROVIDING AND FIXING THIS BOTTLE TRAP 32MM SIZE WITH 190MM LONG WALL CONNECTION P FLANGE (CHROME FINNISH OF APPROVED QUALITY: |
| 551 | PROVIDING AND FIXING WHITE CERAMIC JAQUAR URS-WHT-132530 UNINAL FOR BATHROOM OF APPROVED QUALITY: |
| 552 | Providing and fixing SS Jaquar FLR CHR 5041 2 Way Bib Cock of approved quality: 15 mm nominal bore |
| 553 | Providing and fixing Jaquar Health Brass HEALTH Faucetof approved quality: |
| 554 | Providing and fixing Jaquar Clarion Swan Neck Tap of approved quality: |
| 555 | Providing and fixing Jaquar LONG BODY BIB COCK of approved quality: 15 mm nominal bore15 mm nominal bore |
| 556 | Providing and fixing SANYA Ss Sandwich R Shower, For Bathroom, Dimension/Size: 12x12 of approved quality: 15 mm nominal bore |
| 557 | Providing and fixing Ceramic Jaquar Wash Table Basin of approved quality: |
| 558 | Dormitory cum rest house building (Plumbing and sanitation) |
| 559 | Providing and fixing Ceramic Essco Jaquar stella rimless wall hung wc of approved quality: |
| 560 | Providing and fixing Ceramic Jaquar Wash Table Basin of approved quality: |
| 561 | Providing and fixing CP brass wall mixer 3 -in-1 system with necessary wall flanges complete all. of quality & make as approved by Engineer in charge. |
| 562 | Providing and fixing This Bottle Trap 32mm Size with 190mm Long Wall Connection P Flange. (chrome finish) of approved quality: |
| 563 | Providing and fixing Jaquar Clarion Swan Neck Tap of approved quality: |
| 564 | Providing and fixing Jaquar Health Brass HEALTH Faucetof approved quality: |
| 565 | Providing and fixing Jaquar LONG BODY BIB COCK of approved quality: 15 mm nominal bore |
| 566 | Providing and fixing SANYA Ss Sandwich R Shower, For Bathroom, Dimension/Size: 12x12 of approved quality: 15 mm nominal bore |
| 567 | Providing and fixing Jaquar EXPOSED Prat kit of concealed stop cock of approved quality: 15 mm nominal bore |
| 568 | Providing & Fixing CPVC consealed valve as per ISO:138 / IS-7834 for the operating temperature upto 60 Deg.C threaded type( Inside Bathroom ) 25 mm nominal bore |
| 569 | Supply fixing and testing UPVC SWR pipe confirming to IS:13592 for waste connection from wash basin and pantry sink to floor trap or thermosyphonage pipe with solvent cement joints including all the fittings laid above the fall ceilling connected in wall etc the shall include wall chiseling making good the same in cement mortar etc complete include with all necessary support like GI hangers support GI grip and bolts GI clamp etc in fall ceilling area as well as supplying and fixing GI slotted angle iron bracket hangers supports with necessary drilling holes to suit the insertion of pipe clamps deburring brick work concrete supports etc as per detailed drawing for supporting soil waste and rain water pipes and water supply pipes in shaft with suitable GI clamps GI bolts anchor nuts and washers fixede on shaft walls outer walls etc. 110mm dia |
| 570 | Supply fixing and testing UPVC SWR pipe confirming to IS:13592 (Type - B) for waste connection from wash basin and pantry sink to floor trap or thermosyphonage pipe with solvent cement joints including all the fittings laid above the fall ceilling connected in wall etc the shall include wall chiseling making good the same in cement mortar etc complete include with all necessary support like GI hangers support GI grip and bolts GI clamp etc in fall ceilling area as well as supplying and fixing GI slotted angle iron bracket hangers supports with necessary drilling holes to suit the insertion of pipe clamps deburring brick work concrete supports etc as per detailed drawing for supporting soil waste and rain water pipes and water supply pipes in shaft with suitable GI clamps GI bolts anchor nuts and washers fixede on shaft walls outer walls etc. 40mm dia |
| 571 | Providing and fixing PVC clamps for UPVC SWR pipes of diameter : 110mm dia pipe |
| 572 | Providing fixing and testing UPVC SWR plain ring type 90 Deg Bend IS:14735 110 mm dia |
| 573 | Providing fixing and testing UPVC SWR plain ring type 45 Deg Bend IS: HSN CODE : 39172390110 mm dia |
| 574 | Providing fixing and testing UPVC SWR plain Single Y Branch Door type fitting IS:HSN CODE : 39172390 110 mm dia |
| 575 | Providing fixing and testing UPVC SWR plain Reducing Double Y Branch Door type fitting 110 x 75 mm dia |
| 576 | Providing and fixing and testing UPVC Multi floor trap with SS grating with all necessary UPVC pipes connection extension pipe and reducing tee for wate pipe connections from tiolet and wash area.all floor trap should be 70mm water seal .110 x 75mm Dia |
| 577 | Providing and Fixing uPVC Balcony drain with jali of following size inlet and outlet including cutting and making good the walls and floors wherever required complete in all respects. 75mm dia |
| 578 | Providing and fixing 125 mm dia, 3 mm thick Stainless steel grating with frame for floor traps or drains of required pattern including cutting and making good the floors complete.125mm dia. |
| 579 | Campus Development |
| 580 | Providing & Fixing Stainless Steel Grade 304 Dustbin of Capacity 90 Liter Product id: 5116877-68694698899, Type of Bin:- 1 Bin mounted with 2 pole, Shape of bin:-Cylindrical, , Material of Pole with stand and container (Bin):-Stainless Steel Grade 304, Pole diameter (in mm):-25-28, Pole height (in mm):-1000-1099, Pole pipe thickness (in mm) :-3, Fixing accessories provided:- Yes , as Per Direction Of Engineering In-Charge. |
| 581 | FOOT BALL GROUND -1 nos |
| 582 | Providing and Fixing P/F FOOT BALL GOAL POST AND NET TWO SET Pole Size- 8 X 24 Ft Made of 100 MM Round Pipe Wheel Size- 6 X 2 Inch material mild steel brand Top ten Sport ,all Complete Job as Per Direction Of Engineering In-Charge. |
| 583 | Providing and Applying White StadiumMax Grass Line Marking Paint Concentrate [Pack Of 1] High-quality line marking paint concentrate for football, hockey, cricket & rugby pitches as well as grass tennis courts. 100%water and weather resistant formula for unrivalled longevity. Suitable for spray & wheel-based application. Available in optic white as a pack of 1.All complete job as Per Direction Of Engineering In-Charge. |
| 584 | Providing and Fixing Non Woven Geotextile Membrane 120 gsm Erosion control, soil stability proection of waterproofing coating Plain pattern White color.All complete job as Per Direction Of Engineering In-Charge. |
| 585 | Atheletic Running Track |
| 586 | Providing & Fixing Atheletic Running Track , Usage/Application :- RUNNING TRACK / JOGGING TRACK/, Court Length:- 100MTR / 200MTR / 300 MTR / 400 MTR, Floor Thickness:- 13 - 15MM , Sandwich system as Per Direction Of Engineering In-Charge. |
| 587 | Cricket Pitch |
| 588 | Providing and Fixing 27M X 4M - FORTRESS RUN-UP/SURROUND CRICKET MATTING [GREEN] All Complete job as per doirection of engineer incharge. |
| 589 | Providing and fixing DOUBLE SIDED TAPE FOR CRICKET MATS [1ROLLS]All Complete job as per doirection of engineer incharge. |
| 590 | Providing and fixing FORTRESS 2mm Heavy-Duty Cricket Drop-In Nets - 70ft x 12ft x 12ft /21.3m x 3.6m x 3.6m excellent quality drop-in cricket batting cage nets. Sides, roof & back all pre-sewn for one complete cricket net enclosure. Suitable for indoor and outdoor use. as pe required All Complete job as per direction of engineer incharge. |
| 591 | Providing and fixing Professional Multi-Bay Steel Cricket Cage - 72 x 12 x 12, 34mm, 4 bay alvanised steel cricket cages with a variety of options to choose from. Sizes ranging from 24ft to 84ft, three grades of steel thickness . Durable, long-lasting cricket cage. All Complete job as per direction of engineer incharge. |
| 592 | Providing and Applying White StadiumMax Grass Line Marking Paint Concentrate [Pack Of 1] High-quality line marking paint concentrate for football, hockey, cricket & rugby pitches as well as grass tennis courts. 100%water and weather resistant formula for unrivalled longevity. Suitable for spray & wheel-based application. Available in optic white as a pack of 1.All complete job as Per Direction Of Engineering In-Charge. |
| 593 | Providing and Fixing Cricket Net Clips (80/pack) - Black hard-wearing cricket net clips. Suitable for all net types and any environment. Available in black or white. Ideal for use outdoors .All complete job as Per Direction Of Engineering In-Charge. |
| 594 | ( TWO & FOUR WHEELER PARKING ) |
| 595 | Supply, fabrication, and installation (complete in all respects as per site requirements) of a freestanding Tunnel Car Parking Tensile Shed with a paint-coated steel frame and single side high-strength white PVC fabric cover, UV-resistant and waterproof. The structure, manufactured by New Arts, is plain in design, 10–15 feet in height, and suitable for outdoor parking in residential, commercial, or institutional areas. as Per Direction Of Engineering In-Charge. |
| 596 | Supply, fabrication, and installation (complete in all respects as per site requirements) of a freestanding Tunnel Car Parking Tensile Shed with a paint-coated steel frame and double side high-strength white PVC fabric cover, UV-resistant and waterproof. The structure, manufactured by New Arts, is plain in design, 10–15 feet in height, and suitable for outdoor parking in residential, commercial, or institutional areas. as Per Direction Of Engineering In-Charge. |
| 597 | EXTERNAL ELECTRICAL WORKS |
| 598 | Under/ Over voltage, Master trip relays along with current transformers of 250/5A ratio, 10 VA class-5P10 protection - 1 set ON/OFF/TRIP Indication Ameter with ASS 800 Amps TP&N aluminum conductor bus bar (BPTM type Heat-shrinkable busbar insulation) supported by DMC / FRP insulators.3 nos. 250A FP MCCB 35kA With Thermal Magnetic Based Release (O/C,S/C) Protection & Rom3 nos. 160A FP MCCB 35kA With Thermal Magnetic Based Release (O/C,S/C) Protection & Rom17 nos. 63A FP MCCB 35kA With Thermal Magnetic Based Release (O/C,S/C) Protection & Rom2 nos. 40A DP MCCB 16kA With Thermal Magnetic Based Release (O/C,S/C) Protection & RomMAIN LT PANEL above & as per SLD |
| 599 | Design, manufacturer, supply, testing and commissioning of approx size 1200 mm heightx1000mm wide x 450mm deep of 2.5mm thick sheet metal enclosure, powder coated, weather proof, double door type feeder pillar with godown lock and padlock complete with interconnection with copper wires, LED indicating lights, providing holes for the glands. The base frame shall have angle iron of 50mm x 50mm x6mm of size 1000mm x 450mm with 600mm long legs of MS angle and coverage of underground cable under feeder pillar with 2.5 mm thick sheet, 450mm in width all round the base frame including grouting the feeder pillar in 1:4:8 cement concrete complete as required. Feeder Pillar shall be suitable for 415V, 3-Phase, Four wire, 50 Hz supply complete with earth bus and lifting hooks as required. Approval shall be taken for each panel before fabrication. (All hardwares like nuts and bolts used shall be Galvanized and Zinc passivated ) Feeder Pillar-01, INCOMER, 1 No. 63 amps FP MCCB(25 KA) with thermal Magnetic release (PRMB-3) with Class-C transient voltage surge suppression device suitable for 3 phases as per specifications.Protection Istrument, One (1) Nos. (0-500V) 96 x 96 Sq.mm voltmeter with control Fuse & selector switch. 1 Set of (0-60 Amps) 96 x 96mm CT operated Ammeter with 3 way selector switch and 60 /5A, CL-1, 10VA CT. One (1) Set of Phase Indication & ON/OFF Lamp with 2A Fuse.1 Nos.TIMER suitable for 24Hrs. Setting with Auto/Manual Selector switch with Suitable Contractor , BUS-BAR 1 Set of 200 A TPN Aluminium Bus Bar with colour coded PVC Sleeves (Heat Shrinkable sleeve), OUTGOINGS, 10 No. 32 A 2P MCB, 10 KA, Feeder Pillar-01 |
| 600 | POLESupply, unloading, installation, testing and commissioning of unit with following specifications.30m high (upto the top of head frame) stadium mast with fixed head frame suitable to mount 16 no\"s of 800w LED Floodlight along with foundation bolts, feeder pillar, as required- 4 SetsSuitable Aviation Obstruction Lights of reliable design and reputed manufacturer shall be provided on top of each mast. 4 SetsOne number heavy duty hot dip galvanised lightning finial shall be provided for each mast.The lightning finial shall be minimum 1.2 M in length and shall be provided at the centre of the head frame. It shall be bolted solidly to the head frame to get a direct conducting path to the earth through the mast. The lightning finial shall not be provided on the lantern carriage under any circumstances in view of safety of the system.- 4 SetsSuitable earth terminal using 12 mm diameter stainless steel bolts shall be provided at a convenient location on the base of the Mast, for lightning and electrical earthing of the mast- 4 setsHi-Mast Tower shall be provided with Lightning & Earthing protection through 2(nos.) earth pit , comprising of an Earthing electrode of size 50mm dia, 3 meters Long G.I Pipe with bricks enclosures and cover - 2Nos. (As per relevant IS). Laying and termination of 2 Nos. x 35mm X 6mm G.I strips for interconnection of earthing stud at Mast & Feeder pillar box to earth electrode at earth pit. All metal work including luminaries, control gear units and luminaries carriage shall be bonded to the earth core of the luminaries supply cable. The earth continuity from luminaries carriage shall be via a single core of the multi-core cable- 4 SetsEach mast shall be provided with a feeder pillar fabricated out of 14 SWG CRCA sheet and finished with two coats of red oxide primer and gray enamel paint of shade 631 of IS-5. The feeder pillar shall comprise of incoming 40 amp TPN MCB, Copper wiring, outgoing terminals and contactors-4 Sets ,External Man Rider Unit -1 NOS The luminaries shall be tested as per Indian standards and test reports shall be submitted along with the materials. The luminaries must be suitable for installation on high masts |
| 601 | Supplying and fixing of LED FLOOD LIGHT 800 Watt Energy saving, environment friendly, long life, exclusive innovative die-cast aluminium flood light with highly efficient LEDs as light source, suitable for highlighting architectural features and sports complex.Complete with all fixing accessories as required of Cate. Ref. HAVELLS : JETAFLAUNTFL800W6MLED757MODNMBILTG + ASSEMBLEDCGBOXFLAUNT540WIP or apporoved equivalent.LIGHTING FIXTURE |
| 602 | Supply, Installation, Testing & Commissioning of 1, 2 and 4 port face plate, British Style with Shutter, 2 Plate system clear finish with transparent labelling, ABS-UL94-V2, ROHS Compliant, in accorandce with standards like ANSI/TIA-568-C.2, ISO/IEC 11801:2002 AMMD.2:2010, YD/T 926.3-2009 & ISO/IEC 60603-7 white for I/O fixing at user side. Approved Makes: Derwiser/Nexans/Siemon/Systimax |
| 603 | Supply, Installation, Testing and Commissioning of Workstation PC: Intel(R) Core(TM) i7-3770 Processor (8M Cache, up to 3.90 GHz); RAM: 8GB (1x8GB) Non-ECC DDR3 1600MHz ; Keyboard: 12 function keys; Chassis: Tower/Workstation; DVD: 8X Slimline DVD+/-RW, Data Only; Dual Graphics Card; Network interface card: Integrated Intel(R) 82579LM Gigabit1 Ethernet LAN 10/100/1000; Hard disk: 250GB, 7200 RPM 3.5\" SATA 6Gb/s Hard Drive; Operating system: Windows 7 Professional 64 Bit or latest. Approved Makes: HP / DELL / IBM / LENOVO |
| 604 | Supply, Installation, Testing & Commissioning of Weather Proof Outdoor Enclosure suitable for LIU ,PDU & Switches. Approved Makes: Derwiser/MTS/Rittal/Nexxus/APW |
| 605 | Sever line |
| 606 | Supplying, fixing and testing uPVC SWR pipe confirming to IS:13592 Class-B for waste connection Selfit Socket / Ring fit type from Manhole to Manhole and sewer Network /Chamber to Manhole etc. pipe with solvent cement joints including all the fittings(Fittings As per IS:14735), trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 110mm |
| 607 | Supplying, fixing and testing uPVC SWR pipe confirming to IS:13592 Class-B for waste connection Selfit Socket / Ring fit type from Manhole to Manhole and sewer Network /Chamber to Manhole etc. pipe with solvent cement joints including all the fittings(Fittings As per IS:14735), trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 160mm |
| 608 | Fire detection and alarm system |
| 609 | Supply,installation Addressable Monitor Moudle as per direction of Engineer-in-charge |
| 610 | Fire water pumping sytem |
| 611 | Supply,installation Polycab 16 Core Copper Armoured Cable, 2.5 Sq Mm Cable as per direction of Engineer-in-charge16 × 2.5 sq. mm. |
| 612 | Supplying, erection and terminating FR XLPE insulated galvanised steel wire armoured (round) cable 1100 V, 3 core 70 sqmm copper conductor complete erected with gland & lugs on wall/trusses/pole/laid in provided trench/Pipe as per specification |
| 613 | Providing, fixing, testing and commissioning of full way level operated forged brass ball valve of brass body with forged brass hard chrome plated steel ball tested to a pressure not lass than 15 kg/sq.cm with threaded/flanged complete with nuts, bolts, gaskets, washers etc. as required complete as per direction of Engineer incharge.Supply ,installation,testing & commissioning of Ball valve 15mm |
| 614 | Providing, fixing, testing and commissioning of full way level operated forged brass ball valve of brass body with forged brass hard chrome plated steel ball tested to a pressure not lass than 15 kg/sq.cm with threaded/flanged complete with nuts, bolts, gaskets, washers etc. as required complete as per direction of Engineer incharge.Supply ,installation,testing & commissioning of Ball valve 25mm |
| 615 | Providing & fixing of Pressure Gauge as per direction of Engineer-in-charge |
| 616 | Providing and fixing,testing and commissioning of CI body Rubber seat flange end swing type Foot valve complete with nuts,bolts washers,gaskets. 150 mm diameter |
| 617 | Providing and fixing,testing and commissioning of CI body Rubber seat flange end swing type Foot valve complete with nuts,bolts washers,gaskets. 80 mm diameter |
| 618 | Providing & fixing Air release Valve as per direction of Engineer-in-charge |
| 619 | Providing & fixing 1000 Liter PVC water tank for Priming line. as per direction of Engineer-in-charge |
| 620 | HYDRANT SYSTEM |
| 621 | Supplying and fixing of hose cabinet of size 750mm x 600mm x 250mm made of 2mm thick M.S. sheet with 6mm thick glazed glass door including necessary locking arrangment suitable to accomodate 1 nos. 15 mtr. long hose pipe, 1 no. branch pipe mounted on wall or raised brick platform and duly painted with post office red externally and white internally with synthetic enamel paint complete in all respect. |
| 622 | Providing installation, testing and commissioning of Wafer type non return valve of following sizes conforming to complete with rubber gasket, GI bolts, nuts, washers etc.as required: 100 NB |
| 623 | Providing & fixing of Pressure Gauge as per direction of Engineer-in-charge |
| 624 | Providing & fixing Air release Valve as per direction of Engineer-in-charge |
| 625 | Providing, fixing, testing and commissioning of full way level operated forged brass ball valve of brass body with forged brass hard chrome plated steel ball tested to a pressure not lass than 15 kg/sq.cm with threaded/flanged complete with nuts, bolts, gaskets, washers etc. as required complete as per direction of Engineer incharge.Supply ,installation,testing & commissioning of Ball valve 15mm |
| 626 | Providing, fixing, testing and commissioning of full way level operated forged brass ball valve of brass body with forged brass hard chrome plated steel ball tested to a pressure not lass than 15 kg/sq.cm with threaded/flanged complete with nuts, bolts, gaskets, washers etc. as required complete as per direction of Engineer incharge.Supply ,installation,testing & commissioning of Ball valve 25mm |
| 627 | Providing ,Laying Hume pipe for road crossings 250 NB as per direction of Engineer-in-charge |
| 628 | AUTOMATIC SPRINKLER SYSTEM |
| 629 | Providing installation, testing and commissioning of Wafer type non return valve of following sizes conforming to complete with rubber gasket, GI bolts, nuts, washers etc.as required: 100 NB |
| 630 | Providing installation, testing and commissioning of Wafer type non return valve of following sizes conforming to complete with rubber gasket, GI bolts, nuts, washers etc.as required: 25 mm diameter |
| 631 | Providing & fixing of Pressure Gauge as per direction of Engineer-in-charge |
| 632 | Providing & fixing Air release Valve as per direction of Engineer-in-charge |
| 633 | Providing, fixing, testing and commissioning of full way level operated forged brass ball valve of brass body with forged brass hard chrome plated steel ball tested to a pressure not lass than 15 kg/sq.cm with threaded/flanged complete with nuts, bolts, gaskets, washers etc. as required complete as per direction of Engineer incharge.Supply ,installation,testing & commissioning of Ball valve 15mm |
| 634 | Providing, fixing, testing and commissioning of full way level operated forged brass ball valve of brass body with forged brass hard chrome plated steel ball tested to a pressure not lass than 15 kg/sq.cm with threaded/flanged complete with nuts, bolts, gaskets, washers etc. as required complete as per direction of Engineer incharge.Supply ,installation,testing & commissioning of Ball valve 25mm |
| 635 | Providing, fixing, testing & commissioning of 15mm dia uartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Providing, fixing, testing Automatic Gas Moduler (Clean Agent) as per direction of Engineer-in-charge |
| 636 | Providing, fixing, testing & commissioning of 15mm dia uartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Providing ,Laying Hume pipe for road crossings 250 NB as per direction of Engineer-in-charge |
| 637 | PORTABLE EXTINGUISHERS |
| 638 | Fixing of 6 Kg dry power extinguisher consisting of welded MS cylindrical body with discharge valve, nozzle & CO2 cartage and hanging arrangement complete conforming to IS:2171 |
| 639 | Fixing of 9 Litre Water type CO2 (ISI marked) extinguisher including all accessories with wall bracket & raw plug conforming to IS:940 |
| 640 | Fixing of 6.5 Kg carbon-di-oxide fire extinguishers (ISI Marked) consisting of welded MS cylindrical body, squeeze, lever discharge valve, fitted with internal discharge tube, high pressure discharge hose, discharge nozzle, suspension bracket, finished externally with red enamel paint and fixed to wall with brackets with rawlplug/ dash fastners complete with internal charge conforming to IS:2878. |
| 641 | Fixing 9 Litre Foam type (ISI marked) extinguisher including all accessories with wall bracket & raw plug confirming to IS:10204 |
| 642 | Fixing 10 kg sand bucket (ISI marked) including all accessories, support, stand etc |
| 643 | SIGNAGES |
| 644 | Signage with printe \"FIRE EXIT\" Sign with luminicent colour having size 300 x 100 mm.\" IN CASE OF FIRE, DO NOT USE LIFT. USE STAIRSONLY\" OF 1.5 cm height letters in red with white background. The size of the board shall be 300 x 250 mm |
| 645 | Supply,installation 2 cote of zinc chromate , 2 cote final enamal paint for above ground piping and wrapping coating for under ground piping. |
| 646 | Supply and fixing Structural Steel for pipe support as per direction of Engineer-in-charge |
| 647 | Site plumbing |
| 648 | Providing and fixing brass automatic irrigation sprinkler ,brand name -baison working pressure 5 bar ,bsp male threads 3/4 inch sprinklers diameter of coverage 21m.irrigation system as per direction of engineering In-charge. |
| 649 | Providing and fixing 1 - 6 kg/Cm2 Pressure Booster Pump 1.5 HP Kirloskar CPBS as per direction of engineering In-charge. |
| 650 | Entrance gate |
| 651 | 20W LED BATTEN PLUS LUMILINE: Supply , installation, testing and commissioning of 20W surface and wall mounted LED with aluminium housing & integrated electronic driver. |
| 652 | LED Bulb 10W : Supplying and fixing of LED 10W bulb and accessories as required. |
| 653 | 60W LED FLOOD LIGHT: Supply , installation, testing and commissioning of 60W, LED, flood light. High pressure die cast aluminium material with integrated optics, asymmetric wide beam LED flood light. Protection :IP66 |
| 654 | SPECTATORS GALLERY AND PAVILLION BUILDING |
| 655 | Proving & Fixing White GRC Columns, of size 300 dia with 35mm thick, color:- white, Material :- GRC , Usage/ Application :- Home Décor , Shape: Cirular, all Fixing as per architectural drawings and direction of Engineer-in-charge |
| 656 | Proving & Fixing window Roller Blind of size, Mounting arrangement:- Bracket systems – to install functional roller blind mechanism, Types of roller blind:- Blackout roller blind,Shading solution:-Single roller blind – utilise one layer of fabric (called outer layer), Operating mechanism:-Side winders (that lock the manually adjustable blinds at different levels with the internal ratchet and tension, Opening style Roll up / Roll down, Chain:- type Endless beaded chain , Mounting arrangement :- Bracket systems – to install functional roller blind mechanism, Top roller type :-Aluminium pipe with groove (to fix the fabric in the groove, approved quality as per architectural drawings and direction of Engineer-in-charge |
| 657 | Waterproofing treatment with applying first coat of Sika latex SBR or of approved equivalent, mix with water and cement in ratio of 1:4:7(1 part Sika latex SBR: 4 part water : 7 part cement). The mixture shall be applied with brush for first coat to provide waterproofing to terrace and shall be allowed to dry for 4-5 hours according to temperature conditions. The rate shall be inclusive of preparation of old surface including removing all dirt, dust with wire brushes, grinding the surface to remove fungus etc complete as per instructions of engineer In charge. (Base Coat) (ALL MATERIAL shall be get approved prior to the application.) |
| 658 | Three coat water proofing treatment over base coat consisting of 1 st COAT OF Sikalastic 10 Primer W/ Sikalastic 11 Primer W (or approved equivalent) which shall be applied with BRUSH/ROLLER AND 2nd & 3rd COAT Of Sikalastic 562 IN and each coat will be allowed to DRY FOR 4-5 HOURS AFTER application depending upon TEMPERTATURE CONDITIONS |
| 659 | Providing and fixing fibre mesh of Sika Fabric 50 of approved quality and make for laying between 2nd and 3 rd course of water proofing treatment complete as per the instructions of engineer in charge |
| 660 | 4. Providing one coat of acrylic based single component liquid applied elastomeric water proofing coating Sikalastic 10 Primer W or approved equivalent with synthetic fiber at 20% dilution over a base coat after suitable surface preparation and repair of parent surface including Scraping, crack filling, followed by 2 coats of Sikalastic 520 Cool Coat Fibers IN and Sika Gard XT IN or approved equivalent as finish coat in desired shade as per the direction of the Engineer-in-Charge |
| 661 | Providing & Fixing Auditorium Chair (V2) Product id:-5116877-50221033876, Type of Chair Mechanism:- Auto Seat Tip Up with Sliding Seat with Push Back, Chair Under Structure:- MS under structure with integrated auto tip-up mechanism with suitable welded base plate, Chair legs:- Rectangular MS ERW Tube of size 60 X 40 X 2mm with welded 5 mm thick base suitable base plate from grouting the chair legs and understructure, Chair Under Structure Legs Finish:-Antirust treatment and powder coated, Type of Seat:- Fabric upholstered seat made of PU foam backed with 12mm ±1mm thick moulded plywood with plastic moulded under seat cover, Thickness of PU Foam for Seat (in mm):- 110 millimeter, Colour of Chair:-Red, Warranty of Chair:-2 year, all Job Complete as per direction of Engineer-in-charge |
| 662 | Providing & Fixing Stag Aluminium Alloy Table Tennis - Table, (STAG PETER KARLSSON HIGH LEVEL COMPETITION), Product id:-5116877-9236394027, Material of Top:-Particle Board, Material of Frame & Legs :-Aluminium Alloy,Portability ( Wheels ):- Yes, Number of Wheels:- 4, Size of Wheels:-100 mm, Table Cover:- Yes,Length of the Table:-Rectangular, Length of the Table:-2.74 meter, Width of the Table:-1.525 meter, Height of the Table ( Horizantal Plane from the floor ):- 76 centimeter, Top Thickness:-25 millimeter, Rectangular Frame Pipe Cross section ( Length wise ):-6 centimeter, Wall Thickness of Frame Pipe:-3 mm, Material of Top:-Particle Board, Material of Frame & Legs:- Aluminium Alloy, Material of Wheels:-Rubber, all Job Complete as per direction of Engineer-in-charge |
| 663 | spectators gallery ( Civil) |
| 664 | Proving & Fixing window Roller Blind of size, Mounting arrangement:- Bracket systems – to install functional roller blind mechanism, Types of roller blind:- Blackout roller blind,Shading solution:-Single roller blind – utilise one layer of fabric (called outer layer), Operating mechanism:-Side winders (that lock the manually adjustable blinds at different levels with the internal ratchet and tension, Opening style Roll up / Roll down, Chain:- type Endless beaded chain , Mounting arrangement :- Bracket systems – to install functional roller blind mechanism, Top roller type :-Aluminium pipe with groove (to fix the fabric in the groove, approved quality as per architectural drawings and direction of Engineer-in-charge |
| 665 | spectators gallery ( eletricals) |
| 666 | Supply of 7.5W LED Decorative, wall mounting, antique brass finish fixture with opal glass diffuser suitable for 7.5 W A60 LED filament lamp E27 base, complete with all fixing accessories as required of Cate. Ref. HAVELLS : 1 N x 7.5 W A60 LED Filament Lamp or apporoved equivalent. |
| 667 | indoor badminton cum table tennis building (Civil) |
| 668 | Proving & Fixing window Roller Blind of size, Mounting arrangement:- Bracket systems – to install functional roller blind mechanism, Types of roller blind:- Blackout roller blind,Shading solution:-Single roller blind – utilise one layer of fabric (called outer layer), Operating mechanism:-Side winders (that lock the manually adjustable blinds at different levels with the internal ratchet and tension, Opening style Roll up / Roll down, Chain:- type Endless beaded chain , Mounting arrangement :- Bracket systems – to install functional roller blind mechanism, Top roller type :-Aluminium pipe with groove (to fix the fabric in the groove, approved quality as per architectural drawings and direction of Engineer-in-charge |
| 669 | Waterproofing treatment with applying first coat of Sika latex SBR or of approved equivalent, mix with water and cement in ratio of 1:4:7(1 part Sika latex SBR: 4 part water : 7 part cement). The mixture shall be applied with brush for first coat to provide waterproofing to terrace and shall be allowed to dry for 4-5 hours according to temperature conditions. The rate shall be inclusive of preparation of old surface including removing all dirt, dust with wire brushes, grinding the surface to remove fungus etc complete as per instructions of engineer In charge. (Base Coat) (ALL MATERIAL shall be get approved prior to the application.) |
| 670 | Three coat water proofing treatment over base coat consisting of 1 st COAT OF Sikalastic 10 Primer W/ Sikalastic 11 Primer W (or approved equivalent) which shall be applied with BRUSH/ROLLER AND 2nd & 3rd COAT Of Sikalastic 562 IN and each coat will be allowed to DRY FOR 4-5 HOURS AFTER application depending upon TEMPERTATURE CONDITIONS |
| 671 | Providing and fixing fibre mesh of Sika Fabric 50 of approved quality and make for laying between 2nd and 3 rd course of water proofing treatment complete as per the instructions of engineer in charge |
| 672 | 4. Providing one coat of acrylic based single component liquid applied elastomeric water proofing coating Sikalastic 10 Primer W or approved equivalent with synthetic fiber at 20% dilution over a base coat after suitable surface preparation and repair of parent surface including Scraping, crack filling, followed by 2 coats of Sikalastic 520 Cool Coat Fibers IN and Sika Gard XT IN or approved equivalent as finish coat in desired shade as per the direction of the Engineer-in-Charge |
| 673 | Providing & Fixing Auditorium Chair (V2) SHREE HARIOM ALUMUNIUMR (SHA-AC) Product id:-5116877-50221033876, Type of Chair Mechanism:- Auto Seat Tip Up with Sliding Seat with Push Back, Chair Under Structure:- MS under structure with integrated auto tip-up mechanism with suitable welded base plate, Chair legs:- Rectangular MS ERW Tube of size 60 X 40 X 2mm with welded 5 mm thick base suitable base plate from grouting the chair legs and understructure, Chair Under Structure Legs Finish:-Antirust treatment and powder coated, Type of Seat:- Fabric upholstered seat made of PU foam backed with 12mm ±1mm thick moulded plywood with plastic moulded under seat cover, Thickness of PU Foam for Seat (in mm):- 110 millimeter, Colour of Chair:-Red, Warranty of Chair:-2 year, all Job Complete as per direction of Engineer-in-charge |
| 674 | Providing & Fixing Stag Aluminium Alloy Table Tennis - Table, (STAG PETER KARLSSON HIGH LEVEL COMPETITION), Product id:-5116877-9236394027, Material of Top:-Particle Board, Material of Frame & Legs :-Aluminium Alloy,Portability ( Wheels ):- Yes, Number of Wheels:- 4, Size of Wheels:-100 mm, Table Cover:- Yes,Length of the Table:-Rectangular, Length of the Table:-2.74 meter, Width of the Table:-1.525 meter, Height of the Table ( Horizantal Plane from the floor ):- 76 centimeter, Top Thickness:-25 millimeter, Rectangular Frame Pipe Cross section ( Length wise ):-6 centimeter, Wall Thickness of Frame Pipe:-3 mm, Material of Top:-Particle Board, Material of Frame & Legs:- Aluminium Alloy, Material of Wheels:-Rubber, all Job Complete as per direction of Engineer-in-charge |
| 675 | Dormitory cum rest house building Civil) |
| 676 | Proving & Fixing window Roller Blind of size, Mounting arrangement:- Bracket systems – to install functional roller blind mechanism, Types of roller blind:- Blackout roller blind,Shading solution:-Single roller blind – utilise one layer of fabric (called outer layer), Operating mechanism:-Side winders (that lock the manually adjustable blinds at different levels with the internal ratchet and tension, Opening style Roll up / Roll down, Chain:- type Endless beaded chain , Mounting arrangement :- Bracket systems – to install functional roller blind mechanism, Top roller type :-Aluminium pipe with groove (to fix the fabric in the groove, approved quality as per architectural drawings and direction of Engineer-in-charge |
| 677 | Waterproofing treatment with applying first coat of Sika latex SBR or of approved equivalent, mix with water and cement in ratio of 1:4:7(1 part Sika latex SBR: 4 part water : 7 part cement). The mixture shall be applied with brush for first coat to provide waterproofing to terrace and shall be allowed to dry for 4-5 hours according to temperature conditions. The rate shall be inclusive of preparation of old surface including removing all dirt, dust with wire brushes, grinding the surface to remove fungus etc complete as per instructions of engineer In charge. (Base Coat) (ALL MATERIAL shall be get approved prior to the application.) |
| 678 | Three coat water proofing treatment over base coat consisting of 1 st COAT OF Sikalastic 10 Primer W/ Sikalastic 11 Primer W (or approved equivalent) which shall be applied with BRUSH/ROLLER AND 2nd & 3rd COAT Of Sikalastic 562 IN and each coat will be allowed to DRY FOR 4-5 HOURS AFTER application depending upon TEMPERTATURE CONDITIONS |
| 679 | Providing and fixing fibre mesh of Sika Fabric 50 of approved quality and make for laying between 2nd and 3 rd course of water proofing treatment complete as per the instructions of engineer in charge |
| 680 | 4. Providing one coat of acrylic based single component liquid applied elastomeric water proofing coating Sikalastic 10 Primer W or approved equivalent with synthetic fiber at 20% dilution over a base coat after suitable surface preparation and repair of parent surface including Scraping, crack filling, followed by 2 coats of Sikalastic 520 Cool Coat Fibers IN and Sika Gard XT IN or approved equivalent as finish coat in desired shade as per the direction of the Engineer-in-Charge |
| 681 | Dormitory cum rest house building Eletricals |
| 682 | MDBFabrication, supply, installation, testing and commissionings of cubicle type floor/ wall mounted Main Distribution Board panel made out of 16mm thick CRCA sheet including connection, inter-connection alongwith 4 stsrip aluminium bus bar as per CP WD specifications, ( Part IV - Sub-station) and IS: 8623 comprising of followings panel mounting switchgears etc. as required., Incoming1 Nos. 250 Amps FP MCCB 35KA With Microprocessor based release for O/C,& S/C Protection.One (1) Nos. Three Phase Dual type Digital energy meter with necessary CTs.Protection IstrumentOne (1) Nos. (0-500V) 96 x 96 Sq.mm voltmeter with control Fuse & selector switch.1 Set of (0-250 Amps) 96 x 96mm CT operated Ammeter with 3 way selector switch and 250/5A, CL-1, 10VA CT.One (1) Set of Phase Indication & ON/OFF/TRIP Lamp with 2A Fuse.Busbar300 Amps TP&N aluminum conductor bus bar (BPTM type Heat-shrinkable busbar insulation) supported by DMC / FRP insulators.OUTGOING4 Nos. 63 Amps FP MCCB 25KA With thermal magenetic release for O/C,& S/C Protection.11 Nos. 40 Amps FP MCB 10KA.4 Set of LED ON/OFF Indication Lamp with 2A Fuse.MDB above & as per SLD , NOTE: Contactor will submit the GA Drawings of Panel for Approvel from Clint/Consultant before order the panel. |
| 683 | LIFT PANELINCOMING1 Nos. 63Amps FP MCCB 25kA With Thermal Magnetic release for O/C, S/C & Earth Fault Protection.Digital Dual Type Digital Energy Meter with RS485 showing V, A, PF, KVAR, KWH etc. current transformers of 60/5A ratio, 10 VA Class 1.0 metering.One (1) Set of Phase Indication & ON/OFF Lamp with 2A SP MCB.Control MCB\"S, control terminals & wiring as required.Under/ Over voltage, Master trip relays along with current transformers of 60/5A ratio, 10 VA class-5P10 protection - 1 setSuitable arrangement to receive incoming armored cables.Ameter with ASSVoltmeter with VSSON/OFF/TRIP IndicationOpen/Close Push buttonAuto/Manual selector switchBUSBAR:200 Amps TP&N aluminum conductor bus bar (BPTM type Heat-shrinkable busbar insulation) supported by DMC / FRP insulators.OUTGOINGS:2 Nos. 63amps, 415V FP MCB \"10kA\".2 Nos. 40amps, 230V DP MCB \"10kA\".LIFT PANEL above & as per SLDNOTE: Contactor will submit the GA Drawings of Panel for Approvel from Clint/Consultant before order the panel. |
| 684 | UMDBFabrication, supply, installation, testing and commissionings of cubicle type floor/ wall mounted Sub Distribution Board panel made out of 16mm thick CRCA sheet including connection, inter-connection alongwith 4 stsrip aluminium bus bar as per CPWD specifications, ( Part IV - Sub-station) and IS: 8623 comprising of followings panel mounting switchgears etc. as required., Incoming1 Nos. 63 Amps TP MCCB With Double Neutral 25KA With thermal magenetic release for O/C,& S/C Protection.One (1) Nos. Three Phase Multi Function Meter with necessary CTs.Protection IstrumentOne (1) Nos. (0-500V) 96 x 96 Sq.mm voltmeter with control Fuse & selector switch.1 Set of (0-60 Amps) 96 x 96mm CT operated Ammeter with 3 way selector switch and 60/5A, CL-1, 10VA CT.One (1) Set of Phase Indication & ON/OFF Lamp with 2A Fuse.Busbar200 Amps TP&N aluminum conductor bus bar (BPTM type Heat-shrinkable busbar insulation) supported by DMC / FRP insulators.OUTGOING6 Nos. 40 Amps FP MCB 10KA.UMDB above & as per SLD NOTE: Contactor will submit the GA Drawings of Panel for Approvel from Clint/Consultant before order the panel. |
| 685 | Deep boring |
| 686 | Supplying 100mm dia submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 3HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump. Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages 5 HP |
| 687 | Providing and Fixing 415 V three timer control Panel for Submersible Pumps Si Phase, 5 HP All Complete job as per direction of enngineer incharge. |
| 688 | Providing and Fixing 3 Core 4sq mm Flat copper submersible cable All Complete job as per direction of enngineer incharge. |
| 689 | Providing and Fixing TEXMO 40mm Borewell Column Pipe, 3m All Complete job as per direction of enngineer incharge. |
| 690 | Extra For connection |
| 691 | Supply, installation, testing and commission of 50 KLD sewage treatment plant (MBBR technology) with necessary civil works. Plant size upto 50KLD |
| 692 | Total impact of GST for the purpose of CTC Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
