|
| 1 | M&L brick work with fly ash brick, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) including demolation of brick work of stone masonary built in cement mortor complete all as specified and directed by Engr-in-Chage. |
| 2 | M&L 40mm thick pre cast cement concrete type B-0 1:2:4 (12.5mm graded stone aggregates)louvers and jallies including all mouldings including frames set in cement mortar 1:4 including demolition of existing louvers/jallies complete all as specified and directed directed by Engineer-in-Charge. |
| 3 | S&F mild steel framed work as in Staging for water tanks and the like incl caps, bases etc built up fromtwo or more beam or channel section or angles, MS hollow pipes, MS plates incl lattice bars, stiffeners, gusset plates etc conforming to Fe-290, Gde-E-250 complete all as specified and directed by Engr-in-Charge. |
| 4 | M&L 15mm thick rendering in cement mortar (1:6) on brick work or concrete surfaces, finished even and smooth without using extra cement including taking down cement plaster of any description on brick work or stone masonry walls & racking out Joints, hacking for key, scrubbing downwith water, etc complete all as specified and directed by Engr-in-Charge. |
| 5 | M&L 15mm thick rendering cement mortar (1:4) mixed with liquid water proofing compound onbrick work or concrete surfaces, finished the surfaces even and fair without using extra cement including taking down cement plaster of any description on brick work or stone masonry walls including racking out Joints, hacking for key, scrubbing downwith water, etc complete all as specified and directed by Engr-in-Charge. (WPC shall be paid seperately) |
| 6 | M&L for 10mm thick plaster on roof,ceiling, chajja and roof parapet of CM (1:3) on RCCfinished even and smooth without using extra cementincluding taking down cement plaster of any description on brick work or stone masonry walls including out Joints, hacking for key, scrubbing downwith water, etc complete all as specified and directed by Engr-in-Charge. |
| 7 | Supply only liquid water proofing compound complete all as specified and directed by Engr-in-Charge. |
| 8 | S&F Pre-painted galvalume aluminum zinc coated GI based corrugated steel sheet 0.50mm thick of any colour, having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of plain or corrugated steel sheeting, any gauge/thickness/any type/any pattern complete all as specified and directed by Engr-in-Charge. |
| 9 | S&F Pre-painted galvalume aluminum zinc coated GI based plain steel sheet 0.50mm thick of any colour, having tensile strength of 550 Mpa as in roof covering/cladding to wall, ridge etc fixed with self tapping screws including dismantling of plain or corrugated steel sheeting, any gauge/thickness/any type/any pattern complete all as specified and directed by Engr-in-Charge. |
| 10 | S&F rolled mild steel work of Fe 290 (Gde E-165) as in framed structure, truss, purlins, crane gantries, rails and fastenings and heavy brackets framing (beam, tee, angle, channel, hollow section or flat sections) including distance pieces, cleats, etc complete all asspecified and directed. |
| 11 | S&F mild steel framed work as in grills, gratings etc with ends of bars shouldered and riveted or forged into spikes, framed guard bars, barred iron doors etc, conforming to Fe-290, Gde-E-165 complete all as specified and directed by Engr-in-Charge. |
| 12 | M&L cementconcrete typeC-2 (1:3:6)(Using 40mm graded stone aggregate) as in plinth protection /hardstanding , laid in panels, finished the top surfaces even and fair without using extra cementincluding demolition of cement concrete (un-reinforced) in ground floor and pavings n.exc 15 Cm thick (above or below ground level)complete all as specified and directed by Engr-in-Charge. |
| 13 | M&L Vitrified ceramic coloured light shade tiles double charged(premium)tiles 10 mm thick light shade (Square/Rectangular) area of each tiles exc. 0.42 Sqm but not exc 1.00 Sqm over and including 15mm thick screed bed in Cement Mortar(1:6) in flooring,set and jointed in neat cement slurry and pointed in coloured cement to match the surface including dismantling floor, hearth or wall tiling, including cement mortar bedding (but not backing), removing serviceable tiles to store & rubbish off the premises complete all as specified and directed complete of approved quality complete by Engineer-in- Charge. |
| 14 | M&L Vitrified ceramic coloured light shade tiles double charged(premium)tiles 10 mm thick light shade (Square/Rectangular) area of each tiles exc. 0.42 Sqm but not exc 1.00 Sqm over and including 10mm thick screed bed in Cement Mortar(1:4) in skirting/dado,set and jointed in neat cement slurry and pointed in coloured cement to match the surface including dismantling floor, hearth or wall tiling, including cement mortar bedding (but not backing), removing serviceable tiles to store & rubbish off the premises complete all as specified and directed complete of approved quality completeby Engineer-in- Charge. |
| 15 | M&L for Non skid Endura coloured tiles 12-14mm thick (square/ rectangular) area of each tile not exc 0.16 sqm over and incl 15mm thick screed bed in cement mortar (1:6) in flooring set and jointed in neat cement slurry and pointed in coloured cement to match the surface including dismantling floor, hearth or wall tiling, including cement mortar bedding (but not backing), removing serviceable tiles to store & rubbish off the premises complete of approved quality complete all as specified and directed. |
| 16 | All as per item No 15 above but on verticalsurface over and incl 10mm thick rendering in CM (1:4) complete all as specified and directed |
| 17 | M&L for Glazed ceramic coloured joint free tiles 450x300-350X7-8mm in vertical surfaces over and including 10mm thick rendering in Cement mortar (1:4), set and jointed in neat cement slurry and pointed in coloured cement to match the surface including dismantling floor, hearth or wall tiling, including cement mortar bedding (but not backing) complete of approved quality complete all as specified and directed by Engr-in-Charge |
| 18 | M&L for 18-20mm thick granite (of any type) work (table rubbed and polished) stone slab as in steps, jambs, pillars, window-cills, cooking platforms and including 15 mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust to match with marble shade including dismantling floor, hearth or wall tiling, including cement mortar bedding (but not backing) complete all as specified and directed by Engr-in-Charge |
| 19 | S&F in repairs Aluminium powder coated three track sliding windows with three sliding shutters, (One with and incl stainless steel wire mesh and two with and incl 4mm thick sheet glass panes) aluminium sections not less than 1.1kg per metre for bottom track and top track and side track 0.98 kg per metre, bottom shutter frame 0.55 kg per metre, top shutter frame 0.47 kg per metre, shutter sides, 0.47 kg per metre and interlock sides 0.45 kg per metre including aluminium powder coatedgrill of size 50x50mm, 5mm thick suitable nylon beading channel gasket, nylon rollers Maruthi lock with handles and connected itemsetc complete all as specified and directed by Engr-in-Charge. |
| 20 | S&F in repairs anosided aluminum powder coated window and ventilator side hung type without sash frame of weight not less than 0.75 kg/ RM bar aluminium sections weighting 0.55 kg/ m incl 4mm thick sheet glass pens/SS wire mesh necessary joining cleat, glazing clips, rubber packing, anodised aluminium snap beading, screw, anodised aluminium fittings such as peg stay 150 mm long (1 No) hinges type B-21 100 mm long(2 Nos) Suitable handle (1 No.) including aluminium powder coated grill of size 50 x 50mm,5mm thickcomplete all as specified and directed. |
| 21 | S&F of 100mm longbutt hinges, heavy weight cold rolled mild steel complete all as specified and directed by Engr-in-Charge. |
| 22 | S&F 150mm long, aluminium anodised barrel tower bolts of extruded sections complete all as specified and directed by Engr-in-Charge. |
| 23 | S&F 150mm long aluminium handles caste type anodised complete of approved quality complete all as specified and directed by Engineer-in-charge. |
| 24 | S&F 150mm long aluminium handles, cast type anodisedcomplete of approved quality complete all as specified and directed. |
| 25 | S&F of 250mm long (Length of bolt) fancy type aluminium alloy andodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolt complete of approved quality complete all as specified and directed by Engr-in-Charge. |
| 26 | S&F 150mm alimunium anodised Steel Hasp and Staple, safety type, brass with MS hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed by Engr-in-Charge. |
| 27 | S&F door closer aluminium (extruded sections body) hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000mm in width and weight between 61 to 80 Kg complete all as specified and directed by Engr-in-Charge. |
| 28 | S&F 300mm long mildsheet MS Helical ordinary rat tail rod patterndoor spring including roller and roller plate etc complete of approved quality complete all as specified and directed by Engr-in-Charge. |
| 29 | S&F 140mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, Overall length of cover plate complete all as specified and directed by Engr-in-Charge. |
| 30 | S&F fancy type decorativeStainless steel curtain rod, 25mm dia including brackets and decorative type knobs both side of each rod, incl taking down old curtain rod or pelmet boxes complete of approved quality complete all as specified and directed by Engineer in Charge. Note :- Measurement will be taken between end point of knobs. |
| 31 | S&F Dust/Snake guard aluminium strip in doors of size 40x2mm with rubber at strip bottom complete all as specified and directed by Engr-in-Charge. |
| 32 | Supply and laying of CPVC pipes 20mm outer dia SDR 13.5 pipes and plain CPVC SDR 13.5 fittings on wall/ceiling or laying in floors complete all as specified and directed by Engineer-in-charge. |
| 33 | All as per Ser No 32 and above but CPVC pipes 25mm outer dia. |
| 34 | Cutting chases, pinning in, making good to facing where required and pointing in Cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc and cutting chases for concealed water pipe etc and making good, cutting not exc 10cm width or girth complete all as specified and directed by Engr-in-Charge. |
| 35 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 36 | S&F CPVC 20mm outer dia brass elbow complete all as specified and directed by Engineer-in-charge. |
| 37 | S&F CPVC 20mm outer dia brassTeecomplete all as specified and directed by Engineer-in-charge. |
| 38 | Taking up or down 15mm diasteel tubing and connections including cleaning for re-fixing or removal from site complete all as specified and directed by Engr-in-Charge. |
| 39 | Taking up or down 20mm dia steel tubing and connections including cleaning for re-fixing or removal from site complete all as specified and directed by Engr-in-Charge. |
| 40 | S&F in repair 20mm dia gun metal gate valve with iron wheel haeded screwed both ends to iron pipe and fixed complete all as specified and directed by Engr-in-Charge. |
| 41 | S&F in repair 75mm dia PVC (SWR) pipe single socketed, in any length with rubber ring joints, laid in trenches/floor or fixed to wall including necessary clamps complete all as specified and directed by Engr-in-Charge. |
| 42 | S&F in repair75mm dia PVC (SWR) floor trap with grating including jointing with solvent cement including fixing waste pipe etc complete all as specified and directed by Engr-in-Charge. |
| 43 | S&F in repair PVC vent cowls 75mm complete all as specified and directed by Engr-in-Charge. |
| 44 | S&F in repair PVC connection 15mm bore dia 450mm long with 2 Nos PTMT nuts with washer complete all as specified and directed by Engr-in-Charge. |
| 45 | S&F in repair20mm dia brass CP fancy typetubular towel rail D type600mm long complete of approvedquality complete all as specified and directed by Engr-in-Charge. |
| 46 | S&F in repair chromium plated brass shower roses fancy typewith or without swivel joints 125mm size including shower arm complete of approvedquality complete all as specified and directed by Engr-in-Charge. |
| 47 | S&F in repairbrass CP bib tap 15mm bore fancy type screwed for iron pipe complete with wall flange complete of approvedquality complete all as specified and directed by Engr-in-Charge. |
| 48 | S&F in repair 15mm dia brass chromium plated fancy type pillar tap long body with fly nut capstan head screwed for 15mm bore dia of pipe complete of approvedquality complete all as specified and directed by Engr-in-Charge. |
| 49 | S&F in repair 600x450x5mm thick fancy typelooking mirror bevelled edge of selected good quality glass fixed with stainless steel glass fastner complete of approvedquality complete all as specified and directed by Engr-in-Charge. |
| 50 | S&F in repair CP health faucet with 1m flexible tube and wall hook complete all as specified and directed by Engr-in-Charge. |
| 51 | S&F in repair stop valves cast copper alloy, fancy type chromium plated15mm dia screwed down, high pressure with crutch or butterfly handlees, screwed both ends for iron pipes or for unions complete all as specified and directed by Engr-in-Charge. |
| 52 | S&F in repair stainless steel toilet paper holder fixed to wall with chromium plated brass screws complete all as specified and directed by Engr-in-Charge. |
| 53 | S&F in repair Sheet glass shelf assembly/Glass Corner assembly set of three consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed by Engr-in-Charge. |
| 54 | S&F in repairs 30mm thick Moulded WPC both side laminated Factory made 100% Solid door (Conforming as Per IS:4020) made from 100% LEAD FREE single extruded with 2, 4 or 6 raised panel design on the front side with 10mm deep mould on single side with Wood Grain Texture andback side plain with density not less than 600 kg/cum. Manufactured by an ISO: 9001-2015 certified company. The door should be Waterproof, Termite Proof, Fire Retardent and having screw holding capacity complete all as specified and directed by Engineer-in-Charge. |
| 55 | S&F in repairs 30mm thick Factory made Wiremesh SOLID WPC(Wood Plastic composit) moildede gauged door shutter with wire mesh in any number of division with brown wood grain texture, including S.S wire mesh shall be fixed with 15 x 15 square tube in side rails with screwing 8x28 heat metal zinc coated screws can be removed or fix again after changing of wire mesh when needed. The density of the door shall be as per manufacture instruction complete all as specified and directed by Engineer-in-Charge. |
| 56 | S&F in repairs Factory made 100% Solid WPC Brown door Frame (125mm x 63mm Double Rebate) made from 100% LEAD FREE (single extruded process) material with density 780 kg/Cum & Manufactured by an ISO: 9001-2015 certified company, all as per specification drawing as directed by the Engineer-in-Charge. The door frame should be Waterproof, Termite Proof, Fire Retardent and having excellent screw holding capacity complete all as specified and directed by Engineer-in-Charge. |
| 57 | S&F in repairs Factory made 100% Solid WPC Brown door Frame (75mm x 50mm Single Rebate) made from 100% LEAD FREE (single extruded process) material with density 780 kg/Cum & Manufactured by an ISO: 9001-2015 certified company, all as per specification drawing as directed by the Engineer-in-Charge. The door frame should be Waterproof, Termite Proof, Fire Retardent and having excellent screw holding capacity complete all as specified and directed by Engineer-in-Charge. |
| 58 | S&F in repair fancy type vitreous china white wash basin, (flat back or angle back type) of size 550x400 mm incl cutting for and pinning in ends of brackets or erecting stand of wall hung type with complete accessories, including brackets complete ofapproved quality completeall as specified and directed by Engr-in-Charge. |
| 59 | S&F PVC water storage tank triple layer cylindrical, vertical with closed top with threaded cover hoisted and fixed in position tank capacity 500 Ltr with and including ball valve high pressure of PTMT with epoxy coated Aluminum rod and high density plastic ball screwed for 20mm bore of iron pipe and making connection for inlet and outlet including dismantlingof old water tank and removing from site complete all as specified and directed by Engr-in-Charge. |
| 60 | S&F PVC water storage tank triple layer cylindrical, vertical with closed top with threaded cover hoisted and fixed in position tank capacity 1000 Ltr with and including ball valve high pressure of PTMT with epoxy coated Aluminum rod and high density plastic ball screwed for 20mm bore of iron pipe and making connection for inlet and outlet including dismantling of old water tank and removing from site complete all as specified and directed by Engr-in-Charge. |
| 61 | M&L for preparation newly plastered surfaces ofceiling surfaces and applying two coats of oil bound distemper white or tinted over a coat of primer complete all as specified and directed by Engr-in-Charge. |
| 62 | M&L for preparation old decorated surfaces ofceiling surfaces and applying one coats of oil bound distemper white or tinted complete all as specified and directed by Engr-in-Charge. |
| 63 | M&L for preparation of old decorated surface of internal wall by removing existing treatment with mechanical sander (rpm 1500-2700)along with internal dust extraction system for clean environment certified by reputed paint manufacturers and applying two coats of acrylic distemper using roller over a layer of wall care putty to make the surface smooth all as specified and prescribed by manufacturer of paint and all as directed at site by Engr-in-Charge.Note:- (i) The old surface must be prepared in a manner so that there should not be any impression of dent and it should be made even and smooth all as per manufacture’s instruction before application of distemper.The cost of materials, labour & T&P required for preparation of surface are deemed to be included in the rates quoted.(ii). All the material to be incorporated in the work shall be brought by contractor to MES store yard which will be subsequently issued by department for incorporation in the work to ensure the quantity to be consumed all as per recommendation of manufacture.(iii). After carrying out preparation of surface the same shall be got approved from GEbefore application of distemper for each building.(iv).The colour / shade will be all as approved by GE. |
| 64 | M&L for preparation of old decorated surface of exterior wall by removing existing treatment with mechanical sander (rpm 1500-2700)along with dust extraction system for clean environment certified by reputed paint manufacturers, then washing the surface with Bleaching powder solution for treatment of fungal growth and applying two coats of exterior anti fungal acrylic emulsion paint (Weathercoat of Berger paint or Apex in Asian paint, Nerolac etc having three years of performance warranty) over a coat of exterior water based primer of same make all as specified and prescribed by manufacture of paint and as directed at site by Engineer-in-Charge.Note:- (i) The old surface must be prepared in a manner so that there should not be any impression of dent and it should be made even all as per manufacture instruction before application of distemper.The cost of materials, labour & T&P required for preparation of surface are demand to be included in the rates quoted.(ii) All the material to be incorporated in the work shall be brought by Contractor to MES store yard which will be subsequently issued by department for incorporation in the work to ensure the quantity to be consumed all as per recommendation of manufacture.(iii). After carrying out preparation of surface the same shall be got approved from GE before application of distemper for each building.(iv).The colour / shade will be all as approved by GE.(v) The cost of Scaffolding wherever required are deemed to be included in the rates quoted by the contractor. |
| 65 | All as per Ser item No 64 above but weather coat of berger or apex of asian paint. |
| 66 | M&L two coats of weather proof emulsion paint weathercoatof Berger paint or equvalent in apex or Asian paint, Nerolac etc (having three years performance warranty) over a coat of exterior water based primer of same make in newly plastered surface over a coat of primer incl preparing the surface complete all as specified and directed by Engr-in-Charge. |
| 67 | M&L for preparing new steel and iron surfaces of any description over 10 CM width or girth and applying two coats of synthetic enamel paint of any tint over one coat of red oxide primer complete all as specified and directed by Engr-in-Charge. |
| 68 | M&L cementconcrete typeB-2 (1:2:4)(Using 40mm graded stone aggregate) as insub base including demolition of Cement cencrete (un- reinforced) in GF & pavings n.exc 15 CM thick (above or below GL) complete all as specified and directed. |
| 69 | Cutting openings, through brick walls, or cutting out defective brick work, cutting out brick work for reparir of cracks in brick work and similar work for brick work built in cement mortar or cement lime mortar complete all as specified and directed. |
| 70 | M&L for mild steel TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and incl mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified and directed. |
| 71 | All as per item No.70 above but 5 mm dia and over upto and incl 10 mm dia in stirrups, spacers and binders complete all as specified and directed. |
| 72 | M&L for providing reinforced cement concrete type B1 (1:2:4) (20 mm graded aggregate as in window or door cills, lintels, copings, cover slabs, chullah hoods, chajja, shelves, platform, etc and similar articles in cutting of brick wall for strengthening including demolition of roof, floors (other than ground floors), beams, stair cases, landing, chajjas, cooking platform, etc and similar suspended work reinforced (reinforcement cut as required to facilitate demolition) complete all as specified and directed. |
| 73 | M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where everrequired) and fitting the same with necessarystainless steel nuts and bolts complete, includingfixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel boltsetc., of required size, on the top of floor orthe side of waist slab with suitable arrangement complete all as specified and directed by Engr-in-Charge. |
| 74 | S&F in repair fancy type Vitreous china white wash down couple closet composite type including PVC soft seat cover and flushing cistern (single pattern) white completeof approved quality complete all as specified and directed by Engr-in-Charge. |
| 75 | S&F in repair 18mm thick WPC boardone side laminated and other side plain white colour as in cup board shutters and frames, kitchen cabinet front shutter, partiton, shelf & drawer, fixed with screws, solvent cement/ adhesive complete all as specified and directed by the Engineer-in-Charge. |
| 76 | S&F in repair of Sinks made of stainless steel 1mm thick fancy type kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm and bowl size 410mm x 330mm x 160mm complete of approved quality complete all as specified and directed by Engr-in-Charge. |
| 77 | S&F in repair 15mm dia fancy type brass CP wallmixture (hot & cold) with swinging spout (wall mounted model) with connecting legs and wall flanges screwed down for iron pipe and fixed complete of approved quality complete all as specified and directed by Engr-in-Charge. |
| 78 | S&F in repair 15mm Brass CP fancy typewash hand basin mixer for mixing hot & cold water screwed down for iron pipe and fixedcomplete of approved quality complete all as specified and directed by Engr-in-Charge. |
| 79 | S&F in repair Hydraulic Self Closing hinges 35mm of crank( KH-001) or 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters complete in all respect and fixed in position complete all as specified and directed by Engr-in-Charge. |
| 80 | S&F D-type cabinet handles fancy type premium quality, stainless steel 304/gloss chrome/SN finished 100mm long matt finished complete of approved quality complete fixed in position all as specified and directed by Engr-in-charge. |
| 81 | S&F Ball Catchers 304 grade stainless steel finished suitable for cabinets premium quality complete fixed in position as per manufacturer\"s instruction complete all as specified and directedby Engineer-in- Charge. |
| 82 | M&L forWall Cladding tile 7-8mm thick area of each tile exc 0.10 sqm but n.exc 0.20 Sqm of any colour and pattern set and jointed in neat cement slurry and pointed in white or colour cement to matchincluding 10mm thick rendering on wall in CM 1:4 and surface finished even & fair Complete all as specified and as directed by Engr-in-charge. |
| 83 | M&L for joint free Non-skid ceramic coloured tiles 7-8mm thick (square/rectangular), area of each tile not exc 0.11 Sqm, over and including 15mm thick screed bed in CM (1:6)in flooring, set and jointed in neat cement slurry and pointed in coloured cement to match including dismantling floor, hearth or wall tiling, including cement mortar bedding (but not backing), removing serviceable tiles to store & rubbish off the premises complete all as specified and directed completeby Engineer-in- Charge. |
| 84 | M&L for reinforced precast cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in landings, cover slabs (for manholes etc.), shelves and similar articles with plain faces including necessary form work, set in cement mortar 1:4 including demolition of cement concrete (Un-reinforced) in ground floor and pavings not n.exc 15mm thiick (above & below GL) complete all as specified and directed by Engr-in-Charge.(Note:- Reinforcement shall be measured and paid for separately) |
| 85 | S&F in repair 15mm Brass CP fancy typebath mixer with L bend for mixing hot & cold water screwed down for iron pipe and fixedcomplete of approved quality complete all as specified and directed by Engr-in-Charge. |
| 86 | Dismantling and taking down U/S copper / aluminium point wiring (light, fan, socket, power) complete fitting such as switches, ceiling roses, pendants, lamp holder, light fitting etc including CI/Pressed steel terminals, switch box, and making good the disturbed surface of wall/floor etc, to match with the existing surfaces of wall/floor complete all as specified and directed.Note :- If the contractor fail to make good the disturbed surface of wall/floor etc and do not match with the existing surface of wall/floor to the entire satisfaction of Engr-in-Charge a recovery @ of Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute the decision of accepting officer will be final and binding. |
| 87 | Dismantling and taking down carefully existing DB’s any type and making good the disturbed surfaces of wall/floor to match with the existing wall/floor etc.complete all as specified.Note:- i) Cost of cutting chases of suitable girth where required on brick /concrete surface and making good disturbed surface shall be deemed to be included in quoted rates( ii) If the contractor fail to make good the disturbed surface of wall/floor etc and do not match with the existing surface of wall/floor to the entire satisfaction of Engr-in-Charge a recovery @ of Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute the decision of accepting officer will be final and binding. If the contractor fail to make good the disturbed surface of wall/floor etc and do not match with the existing surface of wall/floor to the entire satisfaction of Engr-in-Charge a recovery @ of Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute the decision of accepting officer will be final and binding. |
| 88 | Material & Labour for Point Wiring for one light Point/one fan point/ one call bell point, controlled by one switch with 1100 volts grade single core conforming to (IS:694 /1990) PVC insulated unsheathed 1.5 sqmm multi stranded copper conductor cable (FRLSH) with contineous earth wire of 1.5 Sqmm stranded copper conductor cable (FRLSH) PVC insulated unsheathed , drawn in and including concealedPVC conduit ,duly concealed to wall/floor or above false ceiling with fittings(ISI marked) not less than 20 mm dia(Color coding of wires shall be Phase, neutral and earth wire all as specified ) sunk Metal flush box with and incl decorative polycarbonate frame for housing Modular Switches, sockets , fan regulators etc including white cover cover plate complete all as specified and directed. Note:- i) Cost of cutting chases of suitable girth where required on brick /concrete surface and making good disturbed surface shall be deemed to be included in quoted ratesii)If the contractor fail to make good the disturbed surface of wall/floor etc and do not match with the existing surface of wall/floor to the entire satisfaction of Engr-in-Charge a recovery @ of Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute the decision of accepting officer will be final and binding. |
| 89 | One 3pin/5pin 5/6 Amps socket out let on same boardwith other switches ,with cables 1.5 sq mm size , complete all as specified and directed. |
| 90 | One 3pin/5pin 5/6 Amps socket out let onindependent board with other switches, with cables 1.5 sq mm size,complete all as specified and directed . |
| 91 | All as per item No 88 abovebut with 2.5 Sqmm PVC insulated FRLSH cable for 15 Amps power point. |
| 92 | S & F Switch Modular single pole, one way 6 Amps, 1 module 240 Volts AC all as specified and directed by Engr- in-charge. |
| 93 | Supply and fixing switch modular , one-way 16Amps,1 module 240 Volts AC all as specified and directed by Engr- in-charge. |
| 94 | Supply and fixing modular socket, 6A -2/3 pin combined 2 module ISI marked 230 volts, 50 Hz all as specified and directed by Engr- in-charge. |
| 95 | Supply and fixing modular socket, 6A/16A -2/3 pin combined 2 module 230 volts 50 hz all as specified and directed by Engr- in-charge. |
| 96 | Supply and fixing bell pushmodular flush type single pole one way 6 Amps, 1 module all as specified and directed by Engr- in-charge. |
| 97 | S&FBell ding dong Type , 240 Voltscomplete all as specified and directed. |
| 98 | Supply and fixing ceiling rose surface bakelite 65x25mm dia having three terminals ISI marked all as specified |
| 99 | Supply and fixings modular fan regulator 120/280 V , For ceiling fan all as specified. |
| 100 | Supply and fixing batton/angle holder insulated body with back plate, suitable for batten fittingsall as specified & directed. |
| 101 | Supply and fixingLED lights fitting 1X20 watt ,4 ftwith extruded aluminium housing heat sink, environmental friendlyenergyefficienttranslucent diffuser with LED light source,2400 Lumens( minimum)coefficient colour temp 6000°K to 6500 °K, surge protection range ≥ 2.5KV, voltage protection range-120-300VAC,2 years warranty ,system efficacy not less than140Lm/Watt for the fitting, power factor >.95,total harmonic distortion< 20% color rendering index>80, fixed on site with all accessoriesincluding connecting up with three core flexible copper conductor cable of suitable size from ceiling rose all as specified & directed. |
| 102 | Supply and fixingenergy efficientLED lights fitting, 9 watt , 230 Volt, of 600 mm length,CCT 6000ºKto 6500° K , decorative ultra slim linear LED lighting fixture with extruded aluminium housing heat sink, environmental friendly, energy efficient LED light source more than1200 lumens , wall mounted mirror batten, integrated electronic driver, system efficacy not less than 140 lumens /watt CCT 6000to 6500°K , surge protection range ≥ 2.5 KV , voltage protection range 120-300 volt AC, power factor > 0.95 total harmonic distortion< 20%, colour rendering index > 80, fixed on site with all accessories including 2 years warranty connecting up with three coreflexible copper conductor cable of suitable size from ceiling rose complete all as specified& as directed.. |
| 103 | S&F LED wall mounted decorative luminaire suitable for LED lamp 9 /12watt B-22 base holder and LED lamp complete all as specified and directed. |
| 104 | S&Fonly round shape 12 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed. |
| 105 | Supply and fixing single pole and neutral enclosure with a two pole and earth plug socket complete with 01 No, RCCB 20 Amp, , 240 Volts,AC Complete all as specified.(Note - Cost of cutting chases for enclosure concealed in wall of suitable girth where required on brick /concrete surface and making good disturbed surface shall be deemed to be included in quoted rates |
| 106 | S & F wall fan 400mm sweep 240 volts Ac 50 Hzcomplete all as directed. |
| 107 | S & F ceiling fan complete 1200 sweep 240 volts Ac 50 Hzcomplete all as directed. |
| 108 | S & F exhaust fan 240 volts Ac 50 Hz 300 mm sweep matellic body (RPM will not be more then 900) including louvers and cutting as required size and shape complete all as directed. |
| 109 | S & F electric water heater storeage type geyser (ISI marked ) 5 star rated inner stainless steel 2 KW of capacity 25 Ltr complete grouting wall with suitable size of nut & bolts washer as required at site with cold water and hot water connection pipe as per required at site,complete all as directed. |
| 110 | S & F electric water heater storeage type geyser (ISI marked ) stainless steel 3 KW of capacity 3 Ltr complete grouting wall with suitable size of nut & bolts washer as required at site with cold water and hot water connection pipe as per required at site,complete all as directed. |
| 111 | S & F PVC fresh airfan 240 volts Ac 50 Hz 250 mm sweep PVC body including louvers and cutting as required size and shape complete all as directed. |
| 112 | Supply and fixingLED building security light 1X30 W housing made out of pressure die-cast aluminium alloy with toughened glass, IP-66 protection, working on 240 Volts , 50 HZ, consisting of reflective lens wired with appropriate driver PF>0.98 having over voltage protection up to 440 volts, Surge protection level ≥ 10 KV, thermal short circuit protection THD < 10% made up of long life LED chips (SMD) in modular with Ra>70, and LED lumen efficiency >140 lumen per watt, beam angle along the drive way, 120 degree, beam angle across the drive way, 80 degree luminior efficiency > 130 Lumens/watt, power LED should be of more than 01 wattCCT should be between 5700° K- 6500° Kincluding fixed onwall with 02 Nos MS clamp made out of 40X6 mm FI and bracket made out of 32 mm dia light grade GI pipe not less than 0.90 mtr long bend to shape completeallas Specifiedand directedincluding connecting with 1.5 sq mm, 3 core, PVC insulated Copper conductor cable 1100 Volts grade from terminalbox to light fittingscomplete all as specified and as directed by Engr-in-Charge (i)the firm has to give warranty for street light fittings including driver minimum for 03 years for any defects developed during the period. (ii) The contractor shall submit the third party LM 79 report from any NABL approved laboratory. (iii)The fitting should have BIS, CRS no. |
| 113 | Supply and fixing sheet metal enclosure double door type for MCBs DB SPN(Single pole and neutral) 240V AC 8 way with 200 Amps rated bus bar all as specified and directed. |
| 114 | Supply and fixing MCB SP 5 to 32 Amp \"B\" series 10 KA repturingcapacity complete all as specified. |
| 115 | Supply and fixing MCBSPN40 Amp 240 V AC 10 KA repturingcapacitycomplete all as specified. |
| 116 | Supply and fixing in repair sub main wiring two single core 4 sq mm PVC insulated unsheathed multi stranded copper conductor cable ( FRLSH ) 1100Volts grade drawn in & including rigid PVC conduit 20mm dia or more medium grade surface/ concealed in wall as per existing along with 4.00 Sq mm PVC insulated unsheathed copper conductor cable (FRLSH ) as earth wire and wire connected withmain earth dolly including cutting chasing and making good disturbed portionall as specified and as directedNote:- Two runs of multi stranded copper conductor cableand one run of earth wire including PVC conduit will be measured as a one length. |
| 117 | Material & labour for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground. ( earth pit not less than 2.25 mtr depth below ground level at any type of strata ) with top edge of the earth plate not less than 1.5mtr below normal ground level connected by 4 mm GI wire as earth lead by means of brass nuts and bolt,thimbles check nuts, washers including concrete chamber of PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish, internal surface of concrete chamber shall be given internal dia 300mm x300mm, 15mm thick plaster in CM 1:4 funnel with wire mesh, RCC pit cover of 320x320x80mm size (1:2:4) Type B1 using 20mm graded stone aggregate rainforced with XPM and charcoal, dust and common salt all as shown in electrical plate No 3 of MES SSR Part-1(2009) and specified including and provision of GI wire upto 7.5 mtrs long with 15 mm dia light grade Gi pipe protection and watering pipe of GI 20 mm bore, medium grade, including all exavation and earth work and connecting the earthing strip to panel, including testing on completion complete all as specified and directed by Engr-in-charge. Note:- (i) RCC pit cover shall be precast of RCC(1:2:4) type B1, 80mm thick rainforced with XPM weighting not less than 4kg/sqm in lieu of CI cover.(ii) Cost of additional GI wire more than 7.5 mtrs will be measured and paid seperately under relevant items. |
| 118 | NOTES :-1.For the items for which specifications not mentioned any where in the tender, the BIS specifications shall be followed. |
