|
| 1 | SEATED PULLER /PULL CHAIRmade from “C” Class G.I pipe.DIMENSIONS: - 1900mm (Length) x 740mm (Width) x 1920mm. (Height). SAFE AREA:- 1.2Mtr x 3Mtr.Seated puller equipment made up of “C” Class G.I. pipe of different NB.NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The center pipe is of 100NB made from “C” Class G.I. pipe. Bottom support is of M.S. round plate of DIA 250 mm & 10mm thickness welded. All linkages are made up of 25NB “C” class G.I. pipe. The handle frame is of 32NB “C” class G.I. pipe. The seat frame is of 32NB “C” class G.I. pipe. To build structure bushes are used which are made from seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush used. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C” class. Welded with M.S. round plate of DIA250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Foundation Cover Closing Cap is made from Injection Moulded Plastic LLDPE / HDPE. The seats and Back rests are fitted on the outer frames are made up of M.S. Sheet of size 330 mm X 300 mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges.Closing Caps are made up of from Injection Moulded Plastic LLDPE / HDPE.Pins used of Diameter 25mm and 17mm are made up from SAE 8620 bright material. The bearings used are of “6205 2RS1” and “6203 2RS1” permanent lubricated sealed bearing of reputed brand.High tensile steel with galvanized nuts & bolts are used for assembly.Thecirclips used for assembly are of A16. The Gym Equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size). |
| 2 | CROSS TRAINER /ELLIPTICAL EXERCISER |
| 3 | DIMENSIONS: - 1320mm (Length) x 600mm (Width) x 1750mm. (Height). SAFE AREA: - 1.77 x 1.2Mtr. Cross trainer equipment made from “C” Class G.I. Pipe of different NB.NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The main frame Pipes are of 80NB “C” Class G.I. Pipe with single bend pipe with 250mm radius. The bottom support of M.S. round plate of DIA250 mm & 10mm thick. The Handle Frame is made up of 25NB “C” Class G.I. Pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C” class welded with M.S. round plate of DIA250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. To build structure bushes are used which are made from M.S. seamless pipe of 60mm OD With 5 mm thickness. The footrests are made from Injection Moulded Plastic LLDPE / HDPE. Closing Caps are made up of Injection Moulded Plastic LLDPE / HDPE. Pins used of Diameter 35mm, 25mm, and 17mm are made up from SAE 8620 bright .The Bearings used are of “6007 2RS1” “62052RS1” and “62032RS1” permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts and bolts are used for assembly. The Gym Equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size). A16 , A 24 mm circlips are used for assembly. Bolt M8X16 mm and NY lock nut of M8 made of SS304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust. |
| 4 | SIT UP BOARD FOR USE OF TWO PERSONS AT ONE TIME. DIMENSIONS: - 1820mm (Length) x 430mm (Width) x 580mm (Height).Safe Area:- 2.8Mtr x 0.6Mtr.Sit up Board Equipment made from “C” Class G.I. pipe of different NB.NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The main frame is of 50mm NB made from “C” Class G.I. pipe in a single bend and supported with the MS round plate of DIA 250x10mm thickness. Fiber reinforced Plastic sheet of 3mm thickness is Bounded on 25mm NB (G.I.) “C” class pipe of main frame. The base support of the sit up board is made 40NB (G.I.) “C” class pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C” class Welded with M.S. round plate of DIA250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. The Gym Equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size). |
| 5 | STANDING SEATING TWISTER. DIMENSIONS: - 1700mm (Length) x 540mm (Width) x 1250mm. (Height). SAFE AREA: - 3 Mtr x 1Mtr.Seating & Standing Twister equipment made from “C” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The Center Pipe is of 100mm NB made from “C” Class G.I. Round Pipe. The M.S. round plate of DIA250 mm & 10mm thickness is welded at bottom. Handle and Bottom sleeve pipe of 125mm OD with thickness 5mm provided for easy assembly, replacement and maintenance. The bottom frame of the Seating & Standing twister is of 32 NB, 50 NB, and 25 NB made from “C” class G.I. pipe. The handle frame of Seating & Standing twister is 25 NB & Foot resting frame of seating side is made from “C” class G.I. pipe of 25mm NB.The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C” class, Welded with M.S. round plate of DIA250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRCA square pipes of 3mm thickness. The Twister plate fitted on the bottom frame is made up of Injection Moulded Plastic LLDPE / HDPE and supported by M.S. Round Plate of size 300mm diameter&10mm thickness. Closing Caps are made up Injection Moulded Plastic LLDPE / HDPE. The Pins used are made up of DIA 35 mm SAE 8620 bright material. The bearings used are of “62052RS1” permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts & bolts are used for assembly. The Gym Equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size). |
| 6 | SKY WALKER DIMENSIONS: - 1720mm (Length) x 630mm (Width) x 1750mm.(Height).SAFE AREA: - 2.7Mtr x 1.6Mtr. Sky Walker Equipment made from “C” class G.I. Pipe of different NB.NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The main frame pipe is of 80mm NB made from “C” Class G.I. Material which is bend at the radius of 250mm.The leg movement frame is of 50 x 50mm x 3mm thick CRC square pipe. Sleeves are made up of 100 mm OD M.S. pipe with thickness 5mm. This results in easy replacement of bearings, pins and handle The handle frame is of 25mm NB made from “C” Class G.I. pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C” class. Welded with M.S. round plate of DIA250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Two foundations are provided for rigid support. The footrests made from Injection Moulded Plastic LLDPE / HDPE. Closing Caps are made up of Injection Moulded Plastic LLDPE / HDPE. The pins used are made up of DIA 25mm SAE8620 bright material. Pins are fixed at the outer end with M8 grub screws and Dia.8mm SS ball. The bearings used are “62052RS1” are permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts & bolts are used for assembly. The cerclips used for assembly are of A24 type. The Gym Equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size). |
| 7 | CHEST PRESS . DIMENSIONS: - 2000mm (Length) x 710mm (Width) x 2200mm. (Height). SAFE AREA: - 3.0Mtr x 1.7Mtr. Chest press equipment made up of “C” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The center pipe is of 100NB made up of “C” Class G.I. pipe. The bottom welded with support of M.S. round plate of DIA250 mm & 10mm thickness. The connecting pipes are made up from 25NB “C” class G.I. pipe. The handle frame is made up from 32NB “C” class G.I. pipe. To build structure bushes are used which are made from MS seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush is used. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C” class. Welded with M.S. round plate of DIA250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. The seats and Back rests are fitted on the outer frames are made up of M.S. Sheet of size 330mm X 300 mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. Closing Caps are made up of Injection Moulded Plastic LLDPE / HDPE. Foundation cover Closing Cap is made from Injection Moulded Plastic LLDPE / HDPE. Pins used of Diameter 25mm and 17mm are made up from SAE 8620 bright material. Bolt M8X16 mm and Nylock nut of M8 made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust. The bearings used are of “62052RS1” &“62032RS1” permanent lubricated sealed bearing of reputedbrand. High tensile steel with galvanized nuts & bolts are used for assembly. The cer clips used for locking is made up of A24 mm & A16mm. The Gym Equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size). |
| 8 | SHOULDER BUILDERProviding and fixing Shoulder Builder made from C- Class GI pipe. The Center Pipe is of 100mm NB made from “C” Class GI pipe, and the bottom support of M.S.Round plate of 250 mm diameter & 10mm thickness is welded at bottom. The handle movement frame is of 25 NB & 20 NB made from “C” Class GI pipe. To Join the centre pipe & handle movement frame seamless pipe of 130mm dia& 3mm thickness is used. The foundation used for fixing consists of three equal items i.e. 100mm NB made from “C” classGI Pipe, M.S. Round Plate of 250 mm dia& 10mm thickness & 25 mm X 25mm X 3mm M.S. angle. Closing caps made from top quality FRP material which is of 2 mm thickness. The pins used are made up of 25 mm dia bright bar. The bearing used be permanent lubricated sealed bearing of reputed make. The nut bolts used for assembly are made from S.S. material. The serclips used for assembly is of 25 mm diameter. The Poly Urethin plastic bush is used for handling. The Gym Equipment shall be finished smooth with a primer coating of at least 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be embedded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size) |
| 9 | BACK EXTENSION DIMENSIONS: - 1400mm (Length) x 700mm (Width) x 820mm (Height). SAFE AREA: - 2.4Mtr x 1.7Mtr. Back Extension Equipment made from “C” class G.I. Pipe of different NB pipe. (NB stands for Nominal Bore i.e. Internal Diameter of pipe in mm) The main frame is of 50mm NB made from “c” Class G.I. pipe. The Foot resting frame of 32mm NB made from ”c” Class G.I. pipe. The handle frame is of 25NB made from “C” Class G.I. pipe. The seat fitted on the outer frames is made up of M.S. Sheet of size 330 mm X 300mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. The foundation used for fixing is consists of 50mm NB made from ”C” Class G.I. pipe.The footrests are made from Injection Moulded Plastic LLDPE / HDPE. The Gym Equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size). |
| 10 | ROWER (DIMENSIONS: - 1200mm (Length) x 1000mm (Width) x 920mm. (Height). SAFE AREA: - 1.5Mtr. x 1.5Mtr.Rower Equipment made from “C” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in mili-meters.The Main frame is of 80NB “C” class G.I. Pipe welded with M.S. round plate of 250mmX10mm. The handle frame 25NB is made from “C” class G.I. pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C” class Welded with M.S. round plate of DIA250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. To join the movement frame to main frame connecting links made up from 32 NB G.I. “C” class pipe. The seat fitted on the outer frames are made up of M.S. Sheet of size 330 mm X 300mmX2mm thickness and deep drawn and pressed tools and dies to have uniform radius of 20 mm with no sharp edges. Pins used of Diameter 17mm are made up from SAE 8620 bright material. The bearings used are of “6203zz” permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts and bolts are used for assembly. The P.U. bushes (Stopper) used to avoid the collision. The cir clips used for assembly is of A 16. The Gym Equipment shall be finished smooth with a primer coating of at least 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1 cement : 2 coarse sand : 4 stone agg. 20mm nominal size). |
| 11 | TAICHI SPINNER( DIMENSIONS: - 700mm (Length) x 1000mm (Width) x 1280mm (Height). Safe Area:- 1.9Mtr X 1.9Mtr Taichi spinner Equipment made up of “C” Class G.I. pipe of different NB.NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The center pipe is of 100NB made up of “C” Class G.I. pipe. The handle movement round frame is made up from 25 NB “C” class G.I. pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB“C” class Welded with M.S. round plate of DIA250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Closing Caps are made up of Injection Moulded Plastic LLDPE / HDPE. The pins used are made up of DIA 25 mm of SAE8620 bright material. The bearing used is “62012RS1” & “62052RS1” permanent lubricated sealed bearing of reputed brand. High tensile S.S. nut bolts are used for assembly. Foundation cover Closing Cap is made of Injection Moulded Plastic LLDPE / HDPE. The cer clips used for assembly is of A24 and A11.The nylon bush is used for handle knob. The Gym Equipment shall be finished smooth with a primer coating of at least 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size). Bolt M8X16 mm and Nylock nut of M8 made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust. |
| 12 | AIR WALKERProviding and fixing Air Walker made from “C” class GI Pipe. The center pipe is of 80mm NB made from “C” Class MS pipe, 32mm NB:- Air Walker pedal frame duly bend, 25mm NB:- Air Walker handle frame duly bend and the bottom support of M.S. round plate of 250 mm dia& 10mm thickness is welded at bottom. MS plate of 245 x 113 x 2.8mm :- Footrest support plate. The leg movement frame is of 40mm NB made from “C” Class MS pipe. The handle frame is of 25mm NB made from “C” Class GI pipe. The foundation used for fixing is consists of three equal items i.e. 80mm NB made from “C” ClassGI pipe, M.S. Round Plate of 250 mm dia & 10mm thickness & 25 mm X 25mm M.S. angle of 3 mm thickness. MS pipe 48 x 48 x 2.8mm:- Footrest frame support. MS Angle 23 x 23 x 1.8mm:- Foundation support frame. MS Flat 48 x 9mm:- Foundation plate support. MS bright material:- Pins made of Dia.25mm. MS plate of 8mm:- Air Walker Pedal L-bend, support. 60mm dia seamless pipe:- Bushes. Bearings:- Permanent lubricated bearings 6205. Closing Caps made from top quality FRP material with 2 mm thickness. HDPE / LLDPE Plastic :- Closing cap, Air Walker Footrest. The pins used are made up of 25mm diameter bright bar. The bearings used bepermanent lubricated sealed bearing of reputed make. The nut bolts used for assembly are made from S.S. material. The ser clips used for assembly are of 25 mm diameter. The Gym Equipment shall be finished smooth with a primer coating of at least 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be embedded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size). |
| 13 | Providing and fixing Surf Board made from “C” Class GI pipe. The center pipe is of 100mm NB made from “C” class GI pipe, and the bottom support of M.S. plate of 250 mm dia& 10mm thickness is welded at bottom. The handle frame is of 40mm NB & 25mm NB made from “C” class GI pipe. The movement frame is made up of 50mm NB “C” class GI pipe. The foundation used for fixing consists of three equal items i.e. 100mm NB made from “C” ClassGI pipe, M.S. round plate of 250 mm diameter & 10mm thickness, 25mm X 25mm X 3mm M.S. angle. To join the centre pipe & handle frame seamless pipe of 130mm dia& 3mm thickness is used. For the movement, bushes are used & for it 60mm dia with 3mm thickness & 60mm solid bar is used. The footrests is made from FRP/C.I./Aluminum casting material, its sizes are 320 mm X 270 mm & 5 mm thickness. For support of footrest is 200mm X 250mm with 5mm thickness M.S. Plate and 50mm X 50mm CRC Square pipe with 2mm thickness is used. Closing Caps made from top quality FRP material which is of 2 mm thickness. The pins used are made up of 25 mm diameter Harden bright bar. The bearing used be permanent lubricated sealed bearing of reputed make. The handles used are of Rubber grip. The Nut Bolts used for assembly is made from S.S. material. The bushes (Stopper) used to avoid the collusion made from Poly Urethin Plastic material of 50 mm dia. The ser clips used for assembly is of 25 mm dia. The Gym Equipment shall be finished smooth with a primer coating of at least 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be embedded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size). |
| 14 | Supply of sign boards of 0.91 x 0.61m size with support length of 3000 mm. Manufacturing, supplying and fixing of Retro reflective sign boards made of 2 mm thick aluminum sheet face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type – IV of ASTM-D 4956-01 in green and silver white including subject matter, message (bilingual(, symbol and borders etc as per IRC: 67-2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 And fixing the same with suitable sized aluminum alloy rivets @ 20 cm c/c to back support frame of m.s angle iron of size 35x35x5 mm and m.s flat of 25x5 mm along with theft resistant measures, mounted and fixed with 2 nos. clamp of mls flats of size 25x5 mm to a vertical post of 3 mtr height made up of msl pipe of 60 mm n.b welded with two hold fast of m.s angle 25x25x3mm of 30cm length each at bottom and including making holes in pipes, angles, providing & fixing m.s message plate of required size, steel work to be paired with two or more coats of synthetic enamel paint of required shade and of approved brand and manufacture over a priming coat of zinc chromate yellow primer (vertical post to be painted in black/white/grey color) Backside of aluminum sheet to be painted with two or more coats of epoxy paint over an appropriate priming coast including all leads and lifts etc. complete as per drawing, specification and direction of Officer-in Charge. |
| 15 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. |
| 16 | Provision and laying in position cement concrete of specified grade excluding and cost of centering and shuttering. Allwork upto plinth level in1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) (as per direction of officer in charge.) |
| 17 | Providing and Laying at or Near Ground Level Factory made kerb stone of M-25 Grade Cement Concrete in position to the required line, Level and curvature, Jointed with cement Mortar 1:3 (1 Cement :3 Coarse Sand), IncludingMaking Joints with or without grooves (Thickness of Joints Except at Sharp Curve Shall not to More Than 5MM), Including Making Drainage Opening Wherever Required Complete etc. As per Direction of Engineer-in-charge (Length of Finished Kerb Edging Shall Be Measured for payment). (Precast C.C. Kerb Stone Shall be Approved by as Per Direction of Officer in Charge) |
