|
| 1 | Demolition of plain cement concrete(un-reinforced) of any description and in any position of thickness not exceeding 15 cm (below or above ground level) and removal of rubbish off from sitecomplete all as directed by Engr-in-Charge. |
| 2 | M & L for 75 mm thick plain cement concrete (1:3:6) mix, type C-1 (using 20mm graded crushedstone aggregate) as in plinth protection, finishing the surfaces even and fair without using extra cement, including 10 mm wide, 75mm deep joints made at 3.00 m in length and filled with bitumen 85/25 gradeand sand in the ratio 1:3 including necessary form work , complete all as specified and directed. |
| 3 | M&L for 10 mm thickvirtrified ceramic (Light shade) tiles polished area of each tilenot exceeding 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mmthick screed bed in CM 1:6 complete all as specified and directed. |
| 4 | M&L for 10mm thickvitrified ceramic ( Light shade) tilespolished area of each tiles not exceeding 0.36 sqm, laidin vertical surface as in dado/skirtingetc over & including10 mm thick rendering in CM 1:4,set & jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed. |
| 5 | M&L for joint free non skid colouredtiles 7 to 8 mm thick(square / rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc., over & including 15mm thick screed bed in cement mortar 1:6, set & jointed in neat cement slurry and pointed with white or coloured cement to match complete all as specified and directed. |
| 6 | M & L glazed ceramic coloured tiles of size 300 mm x 450 mm x7mm thick,as in vertical surfacesuch as dado/skirting etc ,set and jointed in neat cement slurry and pointed in colour cement to match the tiles,over & including 10 mm thickrendering in cement plaster in cement mortar 1:4 complete all as specified and directed. |
| 7 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the allrubbish off from the premises upto 500mtr complete all as specified and directed. |
| 8 | Dismantling of brick work of any description and in any position built in cement or cement lime mortar including all quoins, arches, pillars including segregation of serviceable bricks for reuse & removal of rubbish out offfrom site etc complete all as specified and directed. |
| 9 | M&L for Brick work with sub class bricks old size , straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 etc complete all as specified & directed. |
| 10 | Taking down existing roof treatment any thickness including plastering, leaping plaster of any thickness cuting & up rooting tree roots/vegitable growth & removing the debris from the premises upto 500m from the MOD land including cleaning/washing down and keeping surfaces cleancomplete all as specified and as directed. |
| 11 | M & L for plain cement concrete 1:2:4 ,type B-0 (using 12.5mm graded crushed stone aggregate) mixed with integral water proofing chemical compound, mixed in proportion 200 milli litre per 50 Kg of cement as in padding, benching, sunken portion & on roof surface for correcting/making proper slope on roof, etc.,complete all as specified and directed .(Note:Water proofing compound shall be measured and paid seprerately under respective item of \"BoQ\") |
| 12 | M & L for application of water proofing treatment using APP modified roof membrane over non accessible/ non approachableRCC roof slab / chajjah / canopy / parapet wall( horizontal/vertical surface) to be executed through approved applicator of the membrane manufacturer/authorized applicatorof the manufacturer with following specification etc complete all as specified and directed :-(a) Cleaning existing surface properly with wire brush &apply 10 mm thick plaster /rendering in cement mortar (1:4) mixed with liquid water proofing compound @ 200 ml/50 Kg of cement or as per manufacturer\"s instructions (b) Applying approved bituminousbased primer( conforming to IS: 3384-1995) @ 0.50 litre / Sqm manufactured by the same agency as that of APP membrane with a density 0.87-0.89 Kg per liter at 25 degree centigrade on prepared surface (c) Laying not less than 3mm thick APP (Atactic polypropylene Polymer modified prefabricated membrane) modified water proofing membrane weighing not less than 3.00 Kg/Sqm reinforced with non woven polyster fiber weight not less than 160gms/Sqm using butane torch by torch application with 10cm side laps and 15cm end lap. Physical property of membrane shall be as under :-(i) Membrane weight not less than 3.00 Kg/Sqm. (ii)Non woven polyester weight not less than 160 gms/Sqm.(iii)Softening point of membrane not less than 150degree Celsius. (iv)Joint tensile strength-longitudinal not less than 150 Kg / Sqcm and transverse not less than 450 Kg /Sq.cm at230 degree Celsius. (v) Tear strength - longitudinal not less than 300 N& transverse not less than 250N.(vi)Elongation of reinforcement not less than 30%.(vii) Impermeability under water pressure not less than 3 Kg/Sqcm.(d) APP modified polymeric membrane shall be laid using butane torch by Torch application with minimum 10cm side overlap and 15cm end lap.(e) Applying two coat of bituminiousbased Aluminium Paint @ 0.3 Kg /sqm over APP Membrane. |
| 13 | Supply only liquid water proofing compound ISI mark complete all as specified and directed. |
| 14 | Taking down cement plaster of brick or stone masonry etc including raking out joints,hacking for key & scrubbing down with water etc & removal of rubbish out offfrom site etc complete all as specified and directed. |
| 15 | M&L for rendering 15 mm thick on brick masonry/concrete surface etc incement mortar(1:4) surface finished even & smooth without using extra cement complete all as specified and directed. |
| 16 | M&L for rendering 10 mm thick cement plastering onfair face of brick masonry/concrete surface etcin cement mortar(1:6) surface finished even & smooth without using extra cement complete all as specified and directed. |
| 17 | M&L for 5 mm thickcement plastering in cement mortar 1:4 on concrete ceiling surfaces finished even & smooth without using extra cement omplete all as specifed and as directed. |
| 18 | M&L for preparation of newly plastered surfaceof wall and applying two coats of cement based paint over a coat of alkali resistant primer complete all as specifiedand directed. |
| 19 | M&L for prepatation of new plaster surface andapplyingtwo coats of distemper oil emulsion (OBD) any shadeover a coat of chalk whitening primer and a layer of wall care putty (1.0 mm thick) to make entire surface free from undulations complete all as specifiedand directed |
| 20 | M&L for prepatation of new plaster surface andapplyingone coat of distemper oil emulsion (OBD) any shadeover a coat of chalk whitening primer on ceiling surfaces to make entire surface free from undulations complete all as specifiedand directed |
| 21 | M&L for preparation of old decorated surfaces of ceiling including cornices, by brooming down or steel wire brushing to remove dust, dirt and loose scales of lime wash and other foreign material, scrapping down, smoke soot, moulds, moss and efflorescent salts, trading oil and greasy spots etc including filling the cracks and depressions with putty and applying one coat of distemper oil emulsio nover a coat of primer on ceiling surface at any height complete all as specifiedand directed. |
| 22 | M&L for complete removal of existing treatment from walls (any number of layers) by scrapping with steel scrappers or any other means, including filling depressions of scrapped surfaces withpreparation ofplastered surfaces and applying two coats of cement base paint on wall surface etc.,applying by pump roller applicator of any shade or tint complete all as specified & directed. |
| 23 | M&L for complete removal of old/existing treatment from walls (any number of layers) by scrapping with steel scrappers or any other means, including filling depressions of scrapped surfaces with preparation ofplastered surfaces and apply two coats of distemper oil emulsion (OBD)over a coat of chalk whitening primer applying by pump roller applicator of any shade or tintcomplete all as specified and directed. |
| 24 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exceeding 1.50 sqmeach and removing from site and making good disturbed surface of walls in cement mortar (1:3) complete all as specified & directed. |
| 25 | Taking down chowkats or frames with shuttersexceeding 1.5 Sqm sqm but not exceeding4.00 sqm each (without taking off shutters from the frames) etc including builders hardware etc and removing from site and making good disturbed surface of walls in cement mortar (1:3) complete all as specified & directed. |
| 26 | S&F for 1.25 mm thick pressed steel frames of size 125 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including plain cement concrete 1:3:6, type C-0 (using 12.5 mm graded crushed stone aggregate) as in filling in pressed steel door complete all as specified and directed.Note:The quoted unit rate under this item shall deemed to be included (i) one shop coat of primer (ii) a coat of bitumen paint of inner side of pressed steel door framebefore filling of PCC. |
| 27 | S&F for 1.25 mm thick pressed steel frames of size 105 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including plain cement concrete 1:3:6, type C-0 (using 12.5 mm graded crushed stone aggregate) as in filling in pressed steel door complete all as specified and directed.Note:The quoted unit rate under this item shall deemed to be included (i) one shop coat of primer (ii) a coat of bitumen paint of inner side of pressed steel door framebefore filling of PCC. |
| 28 | S& F 30 mm thick,factory made flush shutters factory made, kiln seasoned and ASCU treated solid core construction, with block board core and ply wood face panels, commercial type on both sides decorative face with lipping/ framecomplete all as specified and directed. |
| 29 | S & F 35 mm thick, factory made, IInd class hard wood glazed and skeleton shuttersopen rebated and prepared to receive glass, gauze, etc. (divided into squares with plain, chamfered or rounded, mitred and rebated sash bars any number size of members),beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, Section 8 clause 8.24 (a); kiln seasoned & chemically pressure treated etccomplete all as specified and directed .(Note:- (i)Glass / wire cloth shall be measured & paid separately.(ii) Sample of shutter in sample room of GE office.) |
| 30 | M&L for framed work such as grills,gratings etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railing; framework of water tanks and similar work conforming to Fe 290- Gde E -165& for portions framed and hung as gates, including pintle hinges, stops,hand-made sliding bolts, etc.complete all as specified and as directed |
| 31 | S&F small fitings of 2nd class hard wood such as brackets of any type, latch and hinge block shape door, window stops and the like incl all necessary labours articles not exceeding 200 cu.cm each complete all as specified and as directed by Engr-in-Charge . |
| 32 | S & F solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with mild steel square tubes suppyling & fixing in opening as per specification & drawing complete all as spcefied and directed by Engineer-in-Charge. |
| 33 | S & F for factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top and bottom rails. mild steel framed shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail &bottom rail on either side & as gap insert for top rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS framed welded/sealed to stiles & rails with suitable PVC sheet beading & joined together with solvent cement complete all asfixing in the frame at site as per specification and drawing complete all as specified and as directed. |
| 34 | S&F powder coated (with coating layer of minimum 50 micron thick) aluminium frame for doors, windows, ventilators shutters(fixed/ sliding track two or three track) and partitions frames with extruded built up standard sections of approved make fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions with sealent with wall, i.e. at top, bottom and sides including cleat angle,C.P. brass/ stainless steel screws, all complete all as specified and directed. |
| 35 | S & F forpowder coated aluminium window , ventilator shutters/sliding shutter with coating layer of minimum 50 micron, Track channel or fixed type without sash bar, aluminum section weighing min 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified. |
| 36 | M & L for40 mm thick plain cement concrete (1:2:4) mix, type B-1 (using 20mm graded crushedstone aggregate ) as in flooring,path,berm etc., finishing the surfaces even and fair without using extra cement including necessary form work, complete all as specified and directed. |
| 37 | M&L plain cement concrete 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate) in for inserting hold fast of doors & window , bed blocks,fillings & similar work etc. including necessary form work complete all as specified and directed. |
| 38 | M&L for prepartion ofnew or previously untreated wooden surface of any description , not otherwise described over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat ofpinkprimer complete all as specified & directed. |
| 39 | M&L for prepartion ofold paintedof wooden surface of any description , not otherwise described over 10 cm in width or girth and applying one coat of synthetic enamel paint on oldwooden painted surface complete all as specified & directed. |
| 40 | M&L for prepartion ofnew or previously untreated steel & Iron surface of any description , not otherwise described over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & directed. |
| 41 | S & F Aluminium anodised handles of extruded section and fixed 125 mm long complete all as specified & directed. |
| 42 | S&F mild steel 200 mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified & directed. |
| 43 | S & F for150 mm (overall length of cover plate) floor door stopperwith rubber shoesaluminium alloy body and tongue, anodised,with hard drawn steel spring,fixed in floor complete all as specified and directed. |
| 44 | S & F Aluminium anodised barrel tower bolts of extruded section and fixed 200 mm long complete all as specified & directed. |
| 45 | S&F250 mm long aluminiumalloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixingclips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixedcomplete all as specified and directed. |
| 46 | S & F for butt hinges, extruded aluminium alloy with galvanised steel hinge pin, anodised type B-21 complete all as specified and directed. |
| 47 | S & F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples etc complete all as specified & directed. |
| 48 | M & L for 3mm thick plain sheet glass ordinary quality and glazing with oil putty not exceeding 0.50 Sqm in each pane,complete all as specified and as directed by Engineer-in-Charge . |
| 49 | S & F in repair 20 mm diamild steel tubing chromium plated curtain rod, 1.0 mm wall thickness includingfixing with fancy brackets,stops, rollers etc.,complete all as specified and as directed by Engineer-in-Charge.Note: Running length of curtain rodshall be measured & paid only. |
| 50 | S&F in repair18/19mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice laminations & other side balancing white laminationfor cupboard shutter, shelf, etc fixed with screws & favicolincluding making holes with decorative covers for wires where ever required fixed complete all as specified and directed. |
| 51 | S & F for 30 mm width of flaps (when open) continuous (piano) hinges,mild steel, bright finish or electrogalvanised complete all as specified and directed. |
| 52 | S&F 40mm dia cupboard knobs fixed with nut, screw and washer of mild steel with brass polish,bright finish complete all as specified and directed |
| 53 | S&F ball catcher with 8mm dia steel ball and brass body and striking plate including letting and fixed complete all as specified and directed |
| 54 | S&F 125 mm size ofhasp and staple safety type aluminium anodized hinges pin including bolt to hinges plate complete etc all as specified & directed. |
| 55 | Taking up or down steel tubing and connections of 15 mm bore or removal to store complete etc and making good the surface in cement mortar 1:3 complete all as specified & directed.all as specified & directed. |
| 56 | S&F for GI water tubing mediumgrade, ISI marked,galvanised, 15 mm bore with all fittings, (such as tee, elbow, socket, union & short pieces) fixed to walls and ceiling or laid in floors including cutting chases for brick wallsand making good the surfacein cement mortar 1:3 complete all as specified & directed. |
| 57 | Refixing for 15 mm bore old steel tubing and connections in new or old position (walls, ceiling,floors, etc.)including all fitting as socket, elbow, nipple,union etc complete all as specified and directed .Note :G I Pipe obtained from item No.- 56 here-in -before. |
| 58 | Taking up or down steel tubing and connections of 20 mm bore or removal to store complete etc and making good the surface in cement mortar 1:3 complete all as specified & directed.all as specified & directed. |
| 59 | S&F for GI water tubing mediumgrade, ISI marked,galvanised, 20 mm bore with all fittings, (such as tee, elbow, socket, union & short pieces) fixed to walls and ceiling or laid in floors including cutting chases for brick wallsand making good the surfacein cement mortar 1:3 complete all as specified & directed. |
| 60 | Refixing for 20 mm bore old steel tubing and connections in new or old position (walls, ceiling,floors, etc.)including all fitting as socket, elbow, nipple,union etc complete all as specified and directed .Note :G I Pipe obtained from item No.-59 here-in -before. |
| 61 | S&F in repair for PVC connection 15 mm dia size with PTMT nuts of length 450 mm complete all as specified and directed. |
| 62 | S&F in repair 15mm bore long body (weight not less than 400 gm) bib tap, cast copper alloy, CP fancy type with crutch or butterfly handle, screw down, screwed for iron pipe or for brass ferrule including flange complete all as specified and directed |
| 63 | S & F shelf of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats 450mm long and 150mm wide (minimum weight 300gms) complete all as specified and directed. |
| 64 | S&F rotational moulded polythene water storage tank of capacity1000 ltrs (Cylindrical/vertical with closed type), triple layer construction, ISI marked, hoisted and fixed in position including 20 mm bore GI nipple and25 mm bore ball/ float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 455 gms)including taking down/dismantling of existing tank complete all as specified and directed. |
| 65 | M&L for plain cement concrete 1:3:6 type C-2(using 40 mm gradedcrushed stone aggregate) as in base of PVC tank etc including necessary form work complete all as specified and directed. |
| 66 | S&F in repair stop valve/cock 20mm bore chromium plated fancy typewith long shank fancy typecast copper alloy, screwed downhigh pressure with crutch or butterfly handlt, screwed both ends for iron pipe or for brass ferrule fixed in wall etc complete all as specified and directed. |
| 67 | S & F in repair angle cock of 15mm bore, chromium platedwith long shank and cup cast copper alloy, screwed down, high pressure, with crutch handle, screwed both ends for brass ferrule,complete all as specified and directed. |
| 68 | S & F in repair stop cock of 15mm bore , chromium platedwith long shank and cup concealed type cast copper alloy, screwed down, high pressure, with crutch handle, screwed both ends for brass ferrule,complete all as specified and directed. |
| 69 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings,heads, shoes, bends, swan-necks,etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specifed & directied. |
| 70 | S & F 110 mm dia PVC rain water pipes single socketed in any length with rubber ring joits fixed to walls with and including stack clamps made out of 40mm by 3mm flat iron and 12mm dia round iron stays and making good the disturbed portion in CM 1:3 to match with surrounding area, complete all as specified and directed. |
| 71 | S&Fin repair PVC (SWR) bends 110 mm dia PVC pipes with rubber ring jointscomplete all as specified & directed. |
| 72 | S & F in repair for 100mm bore, PVC (SWR) pipes, single socketed, in any length, with rubber ring joints laid in trenches or floors complete all as specified & directed. |
| 73 | S & F in repair for 75mm bore, PVC (SWR) pipes, single socketed, in any length, with rubber ring joints fixed on wall including PVC clamps fixed to wall properly including fixing of pipe with PCC (1:2:4) complete all as specified & directed. |
| 74 | S & F in repair for 75mm bore, PVC (SWR) pipes, single socketed, in any length, with rubber ring joints laid in trenches or floors complete all as specified & directed. |
| 75 | S & F vitreous China wash basin, any colour, flat back size 450 mm X 300 mm including 32mm brass chromium platedwaste coupling , 32 mm borePVC waste pipe, chromium plated Gratingincluding cutting for & pinning in ends of bracket or errecting bracket ,fixing of pillar tap & PCC 1:2:4 ,type B-1(using 20 mm graded crushed stone aggregate) for embedding brackets & making good disturbed surface with CM 1:3 complete all as specified and directed.Note : Pillar tap as supply only will be measured & paid seperately under respective item of BOQ. |
| 76 | M&L for 75mm thick plain cement concrete 1:4:8 type D-2(using 40 mm gradedcrushed stone aggregate) as in sub base of flooring, foundations,filling & mass concrete for fencing posts, foundation of pole ,struts & stay assembly etc complete all as specified and directed. |
| 77 | M&L for 80 mm thick factory mademachine pressed chamfered edge pre-cast concrete coloured interlocking paver blockof approved shade, design & pattern , laid as in footpath, light traffic parking etc, made by table vibratory method using PU mould of any shape and size conforming to IS-15658-2006 of M-40 grade laid over &including 50mm thick compacted bedover fine sand, compacting and proper embedding/ laying by vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. |
| 78 | M&L for plain cement concrete 1:2:4, type B-1 (using 20 mm graded crushed stone aggregates) as in kerb/benching/copings including weathering, slightly rounded or chamfered angle and throating including use & waste of necessary form worketc complete all as specified and directed |
| 79 | S & F in repair pillar taps long body chromium plated, cast copper alloy with capstan head, chromium plated, screwed down with or without lettered \"Hot\" or \"Cold\" with long screw shanks and fly nuts, screwed for iron pipe and fixed for 15 mm bore complete all as specified & directed (Make- Shakti Cat Part No API-6108 or equivalent Cat Part No. of any make as per appendix \"A\" to P.S as approved by GE). |
| 80 | S & F in repair brass chromium plated shower rose with swivel joints, 125 mm size in square with CP long shank arm including fixing to steel pipe or union complete all as specifed & as directed. |
| 81 | S & F PVC flushing cistern 10 ltr capacity valve less syphonic action type low level with and including ball valve float and handle, PVC flush pipe 32 mm bore & PVC connection 15 mm bore 450 mm long with PTMT nuts and brackets complete set & making good disturbed surface with CM 1:3 complete all as specified and directed. |
| 82 | S & F600mm X 450 mm bevelled edge looking mirror of selected quality glass mounted on 6 mm thick Acbuilding board or commercial plywood and fixedto wooden plugs with CP brass screw and cup washers complete all as specified and directed. |
| 83 | S&F for vitreous china, squatting pan \" Orissa Pattern\" of size 580 mm X 440 mm white with integral foot rest including cast iron \"P\" or \"S\" trap, front or back inlet and making connection to trap & to flushing cistern completeincluding taking down existing pan & making good disturbed surfacecomplete all as specified &directed. |
| 84 | S&F in repair brass chromium plated towel rail , 20 mm dia ,D-type 600 mm long between flangesfixed with and including chromium platedbrass screw & wooden /plastic cleats complete set all as specified and directed. |
| 85 | S & F PVC (SWR) bends 75mm bore of any radius complete all as specified and directed |
| 86 | S & FPVC (SWR) 110mm bore branch piece, double (double- Y) equal or unequal complete all as specified and directed |
| 87 | S & F PVC (SWR) 75mm bore branch piece, double (double Y) equal or unequal complete all as specified and directed |
| 88 | S&F 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed. |
| 89 | S&F 75 mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed. |
| 90 | S&F 110 mm bore PVC (SWR) junction double, (double T) equal or unequal complete all as specified and directed. |
| 91 | S&F 75 mm bore PVC (SWR) junction double, (double T) equal or unequal complete all as specified and directed. |
| 92 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.complete all as specified and directed. |
| 93 | Taking down ceiling fan/exhaust fanof any sweep after disconnecting all necessaryelectrical connctions from ceiling roseto fan, fan blades and deposit to MES Store yard of AGE E/M Ramgarh complete all as specified and directed. |
| 94 | M & L for point wiring for 15 Amppower point controlled by one 15 Amp with using with FRLSH PVCinsulated PVC unsheathed electric cable conforming to IS:694, 1100V grade AC, single core having multi stranded copper conductor of size 2.5 Sq.mm nominal cross sectional area for phase & neutralandincluding non metallic rigid PVC conduit ISI marked medium grade not less than 25 mm dia with all conduit accessories in concealed wiring system & 2.5 Sqmm green PVC insulated unsheathed multistranded copper conductor as a earth wire connected to earth dolly by providing lugs including sunken type anodized pressed steelsheet terminal box (normal & modular type) made out of 1.6mm thick of suitable size, for mounting fittings/junction boxes including PVC board with bakelite sheet 2.8 mm thick laminatedcover make sheet for housing/ fixingswitches etc.,includingcutting holes for switches,sockets,regulators etc as per requirement includingfixing with machine screw,washer etccomplete all as specified and directed. |
| 95 | All as per item No. 95 here-in-before but one 5 Amps socket outlet on same board. |
| 96 | All as per item No. 95 here-in-before but one 5 Amps socket outlet on independent board. |
| 97 | All as per item No. 95 here-in-before with 2.5 Sqmm (nominal area) FRLSH cable PVC for the 15 Amp 3/5 pin socket power point including 2.5 Sqmm copper conductor green as colour for earth contineuity all as specified. |
| 98 | S & F switch modular single pole one way 6amp 240 volts, 1 Module complete all as specified and directed. |
| 99 | S & F Modular socket 6A-2/3 pin combined 2 Module complete all as specified and directed. |
| 100 | S & F switch modular single pole one way 16amp 240 volts, 1 Module complete all as specified and directed. |
| 101 | S & F Modular socket 16A-2/3 pin combined 2 Module complete all as specified and directed. |
| 102 | S & F steped type modular fan regulator, 120W, 1/2 module complete all as specified and directed. |
| 103 | S&F ceiling rose 3 terminal / PVC/ Polycarbonate, isolated body complete all as specified and as directed.. |
| 104 | S & F LED tube light fitting 1 x 20watt , 220 V, AC, decorative box typewith driver ,holder includingLED tube lightsurface and wall mounted LED battenPVC housing with polycarbonatediffuserand integrated electronic driver complete with all accessories ,driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose to fitting, complete all as specified and as directed by Engineer-in-Charge. |
| 105 | S&F LED light fitting with high out put diffuser 2 feet, 10 watt 220 V AC waith driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge |
| 106 | S & F LED light fitting 1 x 9W/1x10watt ,bulkhead luminaires inlcuding LED light driver, holder connecting up with three core flexible copper conductor cable of suitable sizecomplete all as specified and as directed. |
| 107 | S&F new generation energy saving and environmental friendly long life versatile pressure dec cost aluminium IP 65/66 protection with fish power LED bldg security light of capacity 25/35W 230volt AC outdoor type with pre wired and necessary mounting arrangements ans provision of 2.5 sqmm three core flexible copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as specified and directed. |
| 108 | S&F Lamp holder, PVC/Polycarbonate type with back plate having matching colour to holder suitable for angle/batten fittings (ISI marked) complete all as specified and directed. |
| 109 | S &F LED bulb of capacity 9 watts lumen out put (950 lm) length 113 mmand 60 mm dia, base cap B22, 3 star, (ISI marked) complete with all accessories base (ISI marked) all as specified & directed by Engineer-in-Charge. |
| 110 | S & F for energy efficient exhaust fan of 300 mm sweep made of metal body Ventil Air-DS type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base complete all as specified and directed. Note :- Cost of suitable opening wall for fixing exhaust fan is deemed to be included in overall rate quoted. |
| 111 | Labour only for refixing the ceiling fan/Exhaust fan obtained from item No. 94 above with replacement of unserviceable 3 core PVC insulated PVC sheathed 3 core multistranded copper conductor cable of size 23/0.193 from ceiling rose to fan terminal including over hauling the fan, painting of ceiling fans/ exhaust fans complete with two coats of synthetic enamel paint by spraying including filling cavities with filler after cleaining all dust etc and writing the MES Number with synthetic enamel paint complete all as specified and directed. |
| 112 | S&F in replacement Distribution board (DB) made out of sheet metal enclosure (CRCA sheet) dust and vermin proof TPN 6 way(double door) with suitable Amps rated copper bus bar neutral bar ,earth bar,triple pole and neutral 415 volts ,flush to wall including taking down carefully existing UNSV main switches, DBS along with MCBs complete all as specified and directed. |
| 113 | S & F for 415V 10KA \"C\" curve miniature circuit breaker (MCB) of TPN/FP 40 to 100 Amp capacitypoles and current carrying capacity in the DB complete with connection testing and commissioning complete all as specified & directed. |
| 114 | S & F sheet metal enclosurespowder coated for DBs when MCBs to used singlepole and neutral (SPN) double door 240 volts, 6 way with fixed on wall with suitable amp bus bar and neutral link (ISI marked) EARTH BAR & DIN RAIL confirm to IS:13032-1991 DB including taking down carefully existing unserveciable /old main switches, DBS along with MCBs complete all as specified and directed. |
| 115 | S & F amp rating 240V, 10 KA \"B\" Curve miniature circuit breaker (MCB) of single poles and neutral and current carrying capacity 32 Amp in the MCB DB complete with connection testing and commissioningcomplete all as specified and as directed. |
| 116 | Supply and fixing 240V, 10 KA \"B\" curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 Amp to 32 Amp in the MCB DB Complete with connection testing and commissioning. |
| 117 | M & LSub main wiring with two runs ofsingle core 6.0 Sqmm PVC insulated FRLSH multistanderd copper conductor cable and one run of 6.0 SqmmPVC insulated unsheathedFRLSH multi stranded copper conductor cablefor earth wire drawn in & including concealed rigid non metallic PVC conduit medium grade with fittings (ISI marked) not less than 25 mm dia/appropriate dia with accessories & fittings complete and making good disturbed surface wall including taking down existing sub main wiring complete all as specified and as directed. Note : - Tworuns of 6.0 Sqmm cable andone run of earth wire 6.0 sqmm& conduit shall be measured as one unit length and extra length of cable required for connection to MCBs shall be deemed to be include in unit rate quoted by bidder. |
| 118 | M&L for Earthing complete with galvanizedsteel earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to galvanized earth wire of 4 mm dia (up to 7.5 m in length from earth plate ) by means of bolts, nuts , check nuts and washers of galvanized iron or steel all as specified and shown in electrical plate No.3 of SSR part I including necessary excavation and earth work in any type of soil PCC 1:3:6, type C-1 (using 20 mm graded crushed stone aggregate )chamber with RCC 1:2:4 ,type B-1(using 20 mm graded crushed stone aggregate),40 mm thick pre cast RCCcover with TMT8mm dia at 150mm c/c in both ways as reinforcement, watering funnel, 20 mm dia light grade for protection of earth electrode, 20 mm dia GI pipe light grade for watering including taking down of existing earthing complete all as specified and as directed by Engineer in charge and tested on completion. Note : Rate quoted deemed to be including excavation and earth work in any type of soil with PCC type C1 in pit PCC cover & other arrangement complete all as directed. |
| 119 | Supplying, laying, jointing and testing LT 1100 volt grade XLPE insulated, screened, PVC bedded, galvanised steel strip armoured, electric power cables (heavy duty) with stranded aluminium conductor, cross sectional area25 Sq.mm, 3.5 Core including fixing acessories for laying on wall/ roof/mild steel sturcture ,laid in trenches/ducts, floors etc including taking down existing cable complete all as specified and directed. |
| 120 | M&L for laying GI tubinglight grade 50 mm dia with all fittings for cable protection including GI clamps nut bolts and washer etc all as specified. |
| 121 | Excavation in trenches in soft/loose soil not exceeding 1.5 metre deep and not exceeding 1.5 mtr width and getting out soil including forming bottom surface to required slope/gradient for laying cables/pipes,foundations,laying of cable, shafts, well, cesspits, manholes etc., not exceeding 10Sqm on plan andnot exceeding 1.5m in depth complete all as specified and directed. |
| 122 | Returning, filling in trenchesincluding spreading, leveling, watering and well ramming in layers ofnot exceeding 25 cm thickafter the cables & pipes etc. are laid, jointed & testedand foundations complete all as specified and directed by Engineer-in-Charge. |
| 123 | Removal of surplus excavated soilnot exceeding 50 mtr distance and depositing where directed by Engineer-in-Charge at a level not exceeding 1.5 m above the starting point complete all as specified and directed. |
| 124 | M&L sand filling in cable trenches for cable protection for clean dry sand unwashed including gently punning in a layer of 15 cm and 8 cm (total 23 cm) inthickness all across the laid portion of LT cable in trenches complete all as specified and directed. (Note:-Punned thickness shall only be considered for payment) |
| 125 | Supplying & Laying factory made un-reinforced pre-cast flat concrete cable protection cover of class LV , type- I, size 250 mm x 150mm x 40mm,complete all as specified and directed by the Engineer-in-Charge. |
| 126 | Boring ofhole under road, pavement, hard standing without disturbing existing surface by using hand drilled hand drilled (manual boring)technique and necessary required tools complete all as specified and directed by Engineer-in-Charge.Note : Pipes shall be laid minimum 1.00 mtr below/under existing road surfaces / apron /floors etc.complete all as specified and as directed. |
