|
| 1 | Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sum on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. |
| 2 | 2.8.1 All kinds of soil. |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level : |
| 5 | 4.1.8 1:4:8 (1 Cement : 4 coarse sand : 8 graded stoneaggregate 40 mm nominal size). |
| 6 | Providing and fixing upto floor five level precast cement concrete hollow block including hoisting and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centring, shuttering and finishing smooth with6mm thick cement plaster 1:3 (1 cement : 3 fine sand) on exposed surfacescomplete : |
| 7 | 4.8.1 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) . |
| 8 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement - All work upto plinth level : |
| 9 | 5.1.2 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 10 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement : |
| 11 | 5.2.21:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 12 | Reinforced cement concrete work inbeams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 13 | Centering and shuttering including strutting, propping etc. and removal of form for : |
| 14 | 5.9.1Foundations, footings, bases of columns, etc. for mass concrete. |
| 15 | 5.9.3Suspended floors, roofs, landings, balconies and access platform. |
| 16 | 5.9.5Lintels, beams, plinth beams, girders, bressumers and cantilevers. |
| 17 | 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts. |
| 18 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. |
| 19 | 5.22.3Cold twisted bars |
| 20 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). |
| 21 | 9.1.2Sal wood(Or equivalent wood ) |
| 22 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws excluding, panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. |
| 23 | 9.5.1Second class teak wood (Or equivalent wood ) |
| 24 | 9.5.1.135 mm thick shutters |
| 25 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : |
| 26 | 9.7.1 Second class teak wood (Or equivalent wood ) |
| 27 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all complete. |
| 28 | 9.48.2Fixed to openings /wooden frames with rawl plugs screws etc. |
| 29 | Windows |
| 30 | Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : |
| 31 | 9.96.1300x16 mm |
| 32 | 9.96.2250x16 mm |
| 33 | Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : |
| 34 | 9.97.3 200x10 mm |
| 35 | 9.97.5100x10 mm |
| 36 | Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : |
| 37 | 9.100.1125 mm |
| 38 | 9.100.2100 mm |
| 39 | Providing and fixing aluminium casement windows fastener of required length for aluminium windows with necessary screws etc. complete. |
| 40 | 21.15.1 Anodized (AC 15) aluminium |
| 41 | Providing and fixing ISI marked oxidised M.S. pressed butt hinges with necessary screws etc. complete. |
| 42 | 9.57.1125x65x2.12 mm |
| 43 | 9.57.3 75x47x1.70 mm |
| 44 | Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868)transparent or dyed to required colour and shade with necessary screws etc. complete. |
| 45 | 9.101.1Single rubber stopper |
| 46 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete. |
| 47 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. |
| 48 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 49 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. |
| 50 | 11.41.2Size of Tile 600x600 mm |
| 51 | 12 mm cement plaster of mix : |
| 52 | 13.4.1 1:4 (1 cement : 4 fine sand) |
| 53 | Finishing walls with textured exterior paint of required shade : |
| 54 | 13.45.1New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm |
| 55 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: |
| 56 | 17.7.3 White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps |
| 57 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings andNfixtures complete, including cutting and making good the walls and floors wherever required : |
| 58 | 17.2.1 W.C. pan with ISI marked white solid plastic seat and lid |
| 59 | Extra for providing heavy sheet float glass panes instead of ordinary float glass in glazed doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured) |
| 60 | 9.11.1 5.5 mm thick instead of 4 mm thick. |
| 61 | Applying priming coat: |
| 62 | 13.50.1With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) |
| 63 | Painting with synthetic enamel paint of approved brand and manufacture togive an even shade : |
| 64 | 13.62.1Two or more coats on new work |
| 65 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes butwithout fittings and the base support for tank |
| 66 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand (zone-III) derived from natural sources : 6 graded stoneaggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed andconsolidated and grouted with fine sand, including necessary excavation,levelling & dressing & finishing the top smooth |
| 67 | Providing cement concrete surface drain with 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 40mm nominal size) finished with 1:4 (1 cement: 4 sand) including floating coat of neat cement inside the drain and its top and exposed surface including earthwork in excavation and disposed of surplus earth etc. complete. |
| 68 | 15cm x 15cm surface drain. |
| 69 | Steel work in built up tubular trusses including cutting, hoisting fixing in position and applying a priming coat of approved steel primer, welded and bolted including special shaped washers etc. complete.GI pipes |
| 70 | Steel work welded in built up sections/framed work, including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. |
| 71 | 10.25.2 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 72 | Providing and fixing powder coated aluminium work (minimum thickness of powder coating 50 micron) consisting of tee/ angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P. brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I. level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in charge (level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately). |
| 73 | Providing and fixing plain multipurpose cement board(Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid seperatately). |
| 74 | 12.26.1 6 mm thick Cement fiber board as per IS: 14862 |
| 75 | Providing and fixing plain multipurpose cement board(Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid seperatately). |
| 76 | 12.26.1 6 mm thick Cement fiber board as per IS: 14862 |
| 77 | Providing and fixing PVC Door Frame of size 50x47 mm with a wall thickness of 5 mm (± 0.2 mm), made out of single piece extruded PVC profile, with mitred cut joints and joint with 2 nos of PVC bracket of size 190 mm x 100 mm long arms of cross section size 35 x 15 mm & self driven self taping screws, the vertical door profiles to be reinforced with 40x20 mm M.S. rectangular tube of 0.8 mm , including providing EPDM rubber gasket weather seal throughout the frame, including jointing 5 mm PVC frame strip with PVC solvent cement on the back of the profile. The door frame to be fixed to the wall using 8 x100 mm long anchor fasteners complete, all as per manufacturer\"s specification and direction of Engineer -in- charge. |
| 78 | 35 mm thick factory made Solid panel PVC Door shutter, made out of single piece extruded soild PVC profiles, 5 mm (± 0.2 mm) thick, having styles & rails (except lock rail) of size 95 mmx 35 mm x 5 mm, out of which 75 mm shall be flat and 20 mm shall be tapered (on both side), having one side thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power, including reinforcing with MS tube of size 40 mm X 20 mm x 1 mm, joints of styles & rails to be mitered cut & joint with the help of PVC solvent cement, self driven self tapping screws & M.S. rectangular pipes bracket of size 190 mm X 100 mm of cross section size 35 mm x 17 mm x 1 mm at each corner. Single piece extruded 5 mm thick solid PVC Lock rail of size 115 mm x 35 mm, out of which 75 mm to be flat and 20 mm to be tapered at both ends, having 15 mm solid core in middle of rail section integrally extruded, fixing the styles & rails with the help of solvent and self driven self tapping screws of 125 mm x 11 mm, including providing 5 mm Single piece solid PVC extruded sheet inserted in the door as panel, all complete as per manufacturer\"s specification and direction of Engineer-in-charge. |
| 79 | 9.142.1 Non decorative finish (matt finish) |
| 80 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm + 0.05 %, total coated thickness with zinc coating 120 gsm as per IS: 277 in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 81 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm + 0.05 % total coated thickness, Zinc coating 120gsm as per IS: 277 in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : |
| 82 | 12.51.1Ridges plain (500 - 600mm). |
| 83 | Extra for providing and fixing wind ties of 40x 6mm flat iron section. |
| 84 | Providing and fixing PVC Pipe 4\" approved good quality and complete the works |
| 85 | Providing and fixing PVC Pipe 2\" approved good quality and complete the works |
| 86 | Providing and fixing ofPVC Elbow 4\" approved good quality and complete the works |
| 87 | Providing and fixing of PVC coupler 4\"good quality |
| 88 | Providing and fixing ofPVC Tee4\" approved good quality |
| 89 | Providing and fixing ofPVC Door elbow 2\"good quality |
| 90 | Providing and fixing ofPVC Tee2\" approved good quality |
| 91 | Providing and fixing CPVC syntex tank nipple 1\" approved good quality and complete the works |
| 92 | Providing and fixing CPVC Plain FTA 1 X 1/2\" approved good quality and complete the works |
| 93 | Providing and fixing of CPVC union Socket 1\" inch approved good quality and complete the works |
| 94 | Providing and fixing ofCPVC Plain Coupler 1\" approved good quality and complete the works |
| 95 | Providing and fixing CPVC Pipe1\" approved good quality and complete the works(05 metre) |
| 96 | Providing and fixing CPVC Pipe1\" approved good quality and complete the works(05 metre) |
| 97 | Providing and fixing CPVC Tee1\" approved good quality and complete the works |
| 98 | Providing and fixing ofCPVC Elbow 1\" approved good quality and complete the works |
| 99 | Providing ofCPVC Reducer Tee 25x20mm\"approved good quality and complete the works |
| 100 | Providing ofCPVC Reducer elbow 25x20mm\"approved good quality and complete the works |
| 101 | Providing ofCPVC Plain Reducer 25x20mmpproved good quality and complete the works |
| 102 | Providing and fixing ofCPVC Elbow (3/4\")approved good quality and complete the works |
| 103 | Providing and fixing ofCPVC Tee 1\" approved good quality and complete the works |
| 104 | Providing and fixing ofCPVC Brass Elbow 20x12mm approved good quality and complete the works |
| 105 | Providing and fixing ofCPVC Brass Tee 20x12mm approved good quality and complete the works |
| 106 | Providing and fixing CPVC Solvent resistancefrom corrosionof approved quaity(200ml) |
| 107 | Providing and fixingFTA Brass 20x12mm approved good quality |
| 108 | CPVC Brass MTA 25mm approved good quality and complete the works |
| 109 | Providing and fixing ofCPVC Foot Valve25mm approved good quality and complete the works |
| 110 | Providing and fixingKitchen Sink Cock (wall mount) approved good quality and complete the works |
| 111 | Providing and fixing waste coupler connect thewaste coupler from a sink or other fixtures to the drainage system |
| 112 | Providing and fixing waste coupler connect thewaste coupler from a wash basin or other fixtures to the drainage system |
| 113 | Providing and fixing CP Pillar Cock approved quality |
| 114 | Providing and fixing CP Angular Cock approved good quality and complete the works |
| 115 | Providing and fixting Chorme plated 2-in-1Wall Mixture silver appearance wall mounted approved good quality |
| 116 | Providing and fixing Chrome plated showermade of brass/stainless steel,durability and polished finish uniform water flow elegant appearance approved good qality |
| 117 | Providing and fixingchrome plated 2-way bib cock of approved makewith dual outlets including wall flangefor corrosion resistance and installed with proper sealing |
| 118 | Providing and fixing15mm nominal bore chome plated bib cock solid brass long body wall mounted design including matching wall flange . The product shall be of an approved make and resistance for corrosion |
| 119 | Providing and fixingconnector pipe approved good qualityinlcuding fixing with approved adhesive etc complete |
| 120 | Provinding and fixing health faucet (also known as bidet spray )assembly complete with 1 metre longflexible chrome plated finish all necessary brass fitiing ISI marked product. |
| 121 | Providing and fixing sintex (or approved equivalent)waterstorage tank capacity 500 ltrs including threaded lidmarked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank(for storage) |
| 122 | Providing of S.S.Clamp 2\" |
| 123 | Providing of S.S.Screws |
| 124 | Wiring for light point/ fan point/ exhaust fan point/ call bell pointwith 1.5 sq.mm FRLS PVC insulated copper conductor singlecore cable in surface / recessed medium class PVC conduit,with modular switch, modular plate, suitable GI/Plastic box and earthing the point with 1.5 sq.mm FRLS PVC insulatedcopper conductorsingle core cable etc. as required.Group A |
| 125 | Wiring for twin control light point with 1.5 sq.mm FRLS PVCinsulated copper conductor single core cable in surface /recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5sq.mm FRLS PVC insulated copper conductor single core cableetc. As required. |
| 126 | Wiring for power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 127 | Wiring for circuit/ sub main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. |
| 128 | a) 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire. |
| 129 | b) 2 X 10 sq. mm + 1 X 10 sq. mm earth wire. |
| 130 | Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. |
| 131 | Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. |
| 132 | Supplying and fixing brass batten/ angle holder including connection etc. as required. |
| 133 | Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Upto 450 mm sweep. |
| 134 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 12 way, Double door. |
| 135 | Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. |
| 136 | Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A |
| 137 | Supplying and fixing suitable size GI /PVC box/ with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. |
| 138 | Supplying and fixing suitable size GI/PVC box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. |
| 139 | Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required |
| 140 | Installation, testing and commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/ LED lamps per fitting, complete with all accessories including connections etc. as required. |
| 141 | Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required. |
| 142 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole |
| 143 | Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required. |
| 144 | Supplying of 18/20 W LED tube light batten luminaire |
| 145 | Supplying ofBLDC Ceiling Fan 1200 MM sweep complete set 5 star |
| 146 | Supplying of 200mm sweep Exhaust Fan |
| 147 | Supplying Of B/C LED BULB 9W |
| 148 | Supplying ofLED batten 10 W |
