|
| 1 | M& L for Surface dressing n exc 15 cm deep including site clearance of any type of soil complete all as specified and as directed. |
| 2 | Excavation in trenches, n.exc 1.5m wide and n.exc 1.5m depth for foundation etc. or for shafts, wells, cesspits, manholes, pier holes, taking up/ laying of underground cableand getting out in any type of soil complete all as specified and as directed. |
| 3 | Returning, filling in trenches of any type of soil including spreading, leveling watering and well ramming in layers not exceeding 25 cm thick complete all as specified and as directed. |
| 4 | Removing of excavated soil not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point all as specified and directed. |
| 5 | M&L for PCC (1:4:8), type D-2 using 40mm graded stone aggregates as in foundation, filling and mass concretecomplete all as specified and directed. |
| 6 | M&L for Use & waste of formwork to sides and soffits of floor or roof beam,beam haunchings, girders, bressummers, lintels, catilevers, shelves including sup-ports, overhangs, at also splays between floor and beams etcin rough finished flat surface of concrete complete all as specified and directed. |
| 7 | M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to battercomplete all as specified and directed. |
| 8 | M&L for formwork to sides of columns, post, struts, piers and stenchions for fair finished surface complete all as specified and directed. |
| 9 | M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 10 | M&L for mild steel TMT bars 6mm to 10mm diacut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends as in stirrups, spacers and binders including binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 11 | M&L for reinforced cement concrete Type M-25 (Design mix) (20mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns etc basement slabs, under-reamed piles and mass concrete complete all as specified and directed |
| 12 | M&L for reinforced cement concreteType M-25 (Design mix) (20mm graded stone aggregate) as in Beams, cantilevers, bressummers, lintels over 1.5m spane complete all as specified and directed. |
| 13 | M&L for reinforced cement concreteType M-25 (Design mix) (20mm graded stone aggregate) as in Columns, pillars, piers, posts and struts complete all as specified and directed. |
| 14 | M&L for reinforced cement concrete (1:2:4) Type M-15 (nominal mix) (20mm graded stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies,canopies, deck slabs and in shelves complete all as specified and directed. |
| 15 | Earth filling under floors, spreading, levelling in layers n exc 25cm thick each including watering & well ramming complete all as specified and directed.(Note: (i) Earth obtain from item No 2.00 above shall be filled in this item. (ii) Cost of earth not consider in this item but costof spreading, levelling, watering, well ramming are included in this item.) |
| 16 | M&L for brick work with fly ash bricks, straight or curved on plan exc 6 m mean radius, built in cement mortar (1:6) complete all as specified and directed. |
| 17 | M&L for brick work with fly ash bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar (1:4) complete all as specified and directed. |
| 18 | M&L for 40mm thick in cement concrete (1:2:4), Type B-0 (using 12.5mm crushed stone aggregate) ofdamp proof course to horizontal or vertical surfaces including necessary formwork complete all as specified and directed. |
| 19 | M&L for damp proof course applying bitumen blown any grade, applied hot,two coats, to concrete surfaces at the rate of 1.5kg. per sq. m per coat Complete all as specified and directed |
| 20 | Excavating over areasn.exc 1.5m deepand getting out in any type of soil complete all as specified and as directed. |
| 21 | Excavating over areas exc 1.5mand n. exc 3.0 m deep and getting out in any type of soil complete all as specified and as directed. |
| 22 | M&L for rendering 15 mm thickon concrete/brick surface on wallin cement mortar (1:6) other than fair face of brick work, finished even and smooth without using extra cementcomplete all as specified and directed. |
| 23 | M&L for rendering 15 mm thick in cement mortar (1:4) on fair faces of brick or concrete surface , finished even andsmooth without using extra cement complete all as specifed and directed. |
| 24 | M&L forapplying two coats of oil bound distemper (premium quality) over one coat of alkali resistant primer paint over a layer of smooth wall putty finish punning 2 mm thick on new plaster surface strictly as per manufacturer instruction with smooth roller finish complete all as specified and directed by GE.(Note:- After painting works, cleaning of all floors, glass and furniture by own arrangement) |
| 25 | M&L for preparation of Newplastered or un-plasteredwall surfaces and applying two or more coats of 100% premium quality acrylic emulsion paint (Apex ultima) having VOC less than 50gm/ Ltr and UV resistence as per IS 15489:2005, alkali and fungal resistance, dirt resistance exterior paint of required shade (company depot tinted) with slilicon additive @ 1.43 ltr/10 Sqm over and including a coat of exterior primer applied @ 0.902 ltr/ 10 Sqm with roller finish complete all as specified and directed by GE. (Note:- After painting works, cleaning of all floors, glass and furniture by own arrangement) |
| 26 | M&L for hard core of broken stone or boulders of gauge not exc 63mm deposited spread and leveled in layers not exceeding 15cm thick watered and rammed to a true surface complete all as specified and directed. |
| 27 | M&L for 75mm thickPCC (1:3:6), type C-2 (using 40mm graded stone aggregates) as in sub base of floorscomplete all as specified and directed. |
| 28 | S &F for structural steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 complete all as specified and directed. |
| 29 | M & L for Hand rails, wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for ecuring wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar workonforming to Fe-290 Gde E-165 complete all as specified and directed |
| 30 | S&F for pre-painted galvalume aluminium zinc coated GI based corrugated steel sheet 0.50mmthick of approved colour having tensile strength 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws including side and end lap as per manufacturer’s instructions complete all as specified and directed. |
| 31 | S&F for pre-painted galvalume aluminium zinc coated GI based plain steel sheet 0.50mmthick of approved colour having tensile strength 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws including side and end lap as per manufacturer’s instructions complete all as specified and directed. |
| 32 | M&L for plates Fe-410-W (Gde-E-250) quality-B (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and directed. |
| 33 | M&L for preparation of new or previously untreated steel surfaces of any description, over 10cm in width or girth andapplying two coats of synthetic enamel paint over a coat of red oxide zic chrome primer complete all as specified and directed. |
| 34 | M&L for 4mm thick E-board fixed in ceiling and including aluminium anodised snap grid frame work as in false ceiling all as specified size of grid 605x605 mm with aluminium main T section of size 36.5 x25 mmx 1.4 mm weighing 0.24 kg per running metre and cross T of size 23.5 x 26.4 x1.4mm weighing 0.191 kg per RM with aluminium wall angle size 40 x 25 x 2 mm including GI supporting wire of 3mm dia including dismantling of wall and ceiling (fibre, pulp, insulation board/salbs/blankets) complete all as specified and directed. |
| 35 | M&L for non skid ceramic coloured tiles 7 to 8 mm thick (premium quality) Square/rectangular, area of each tile exceeding 0.06 sqm but n.exc 0.11 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over and including 15mm thick screed bed in cement mortar (1:4) complete all as specified and as directed. |
| 36 | M&L for glazedceramic coloured tiles of size 450x350x7mm thick,(premium quality)on vertical surface of wall such as dado, skirting, riser etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over and including 10mm thick screed bed in cement mortar (1:3) complete all as specified and as directed. |
| 37 | M&L for 20mm thick granite stone slab (of any type) work (table rubbed and polished) in skirting/dado, steps, pillars, window sills, cooking platform etc. laid over 20mm thick bedding in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of granite slab including rounding edges of granite complete all as specified and directed. |
| 38 | S&F for solid PVC door frame of size 50mmx47mm made out of 5mm wood grain printed colour PVC sheet and edges will be printed to match with printed sheet, reinforced with MS square tube as per specification and drawing complete all as directed. |
| 39 | S&F for 28 to 30mm thick (stiles) Factory Made Solid PVC Moulded Door Shutter with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain Moulded PVC Sheet polyurethane painted on the front face & 2mm prelam on front face and 2mm prelam PVC sheet on back face and fixed in frame at site as per specification & drawing complete all as specified and directed. |
| 40 | S&F for 100 mm long Butt hinges (medium weight) stainless steel complete all as specified and directed. |
| 41 | S & F for 150 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed. |
| 42 | S &F foraluminium alloy, anodised, sliding door bolt 250mm long, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloycomplete all as specified and directed. |
| 43 | S & F for 150 mm long aluminium alloy handles, cast type, anodized complete all as specified and directed. |
| 44 | M&L for 15mm diabib tap long body with wall flange cast copper alloy with crutch or butterfly handle, chromium plated, fancy type, screwedfor iron pipe completeas in repair all as specified and directed.(Make:-Jaquar, Cat No CON-107KN or equivalent of Hindware/ Kohler/Parryware) |
| 45 | S&F for 15mm bore pillar tap fancy type cast copper alloy with capstan heads chromium plated screwed down or high pressure with or without lettered hot or cold with 450mm long braided hoses screwed shank and fly nuts for iron pipe fixedcomplete as in repairall as specified and directed.(Make:-Jaquar, Cat No CON-011KN or equivalent of Hindware/ Kohler/Parryware) |
| 46 | S&F for 15 mm dia concealed stop cock with fitting sleeves, operating lever & adjustable wall flange with seal (comatible with ALD-083FT& ALD-089FT) valves cast copper chromium platedwith long shank and cup (concealed type) fancy type screwed down high pressure screwed both ends for pipe complete as in repair all as specified and directed.(Make:-Jaquar, Cat No CON-083FTK or equivalent of Hindware/ Kohler/Parryware) |
| 47 | M&L for 15mm dia angular stop cock with wall flange cast copper alloy with crutch or butterfly handle, chromium plated, fancy type, screwedfor iron pipe complete as in repairall as specified and directed.(Make:-Jaquar, Cat No CON-059KN or equivalent of Hindware/ Kohler/Parryware) |
| 48 | S&F for Brass chromium plated towel ring with round flange complete as in repair all as specifed and directed.(Make:-Jaquar, Cat No ACN-1121N or equivalent of Hindware/ Kohler/Parryware) |
| 49 | S&F for EWC with wall hang cistern, drainage L bend pipe, gasket and installation kit with PP normal close seat cover, Hinges, fixing accessories and accessories set of size 350mm x 450mm x 395mm \"S\" trap including to existing water supply ling and water closet pan complete as in repair all as speicified and directed.(Make:-Jaquar, Cat No CNS-WHT-551SNPP184LZ or equivalent of Hindware/ Kohler/Parryware) |
| 50 | S&F for corner shelf with bracket complete as in repair all as specified and directed. (Make:-Jaquar, Cat No CAN-1173 or equivalent of Hindware/ Kohler/Parryware) |
| 51 | S&F for soap dish hold type including chromium plated brass screws and wooden plastic cleats complete as in repairall as specified and directed.(Make:-Jaquar, Cat No AKP-35731P or equivalent of Hindware/ Kohler/Parryware) |
| 52 | S&F for CP brass health faucet of 8mm dia, with 1.2 mtr long flexible tube and wall hook with back flow preventer including all fittings complete as in repair all as specified and directed.(Make:-Jaquar, Cat No ALD-573 or equivalent of Hindware/ Kohler/Parryware)\" |
| 53 | S&F for 600x450mm bevelled edge mirror of selected quality glass with PVC packing as approved by GE fixed to wall/ wall tiles to silicon paste including necessary fixing arrangement completeas in repair all as specified and directed. |
| 54 | S&F forvitreous China wash basin table top, white, flat back, size 425mmx 425mm x 145mm including bottle trap of size 32mm with 250mm & 190mm long wall connection pipes and wall flanges (but exclusive of fixing of supply waste pipe, tap) completeall as specified and directed.(Make:-Jaquar, Cat No ONS-WHT-01901 for table top basin, Cat NoALD-769L250X190 for bottle trap or equivalent of Hindware/ Kohler/Parryware) |
| 55 | S&F for vitreous china urinals (top inlet) of size 345mmX320mmX610mm, white with fixing accessories, bowl type, complete including providing and fixing plus, bedding urinal against wall in cement mortar (1:2) securing urinal to plus with and including 60mm long brass screws, pointing around urinal back in cement, fixing with flush pipe, grating and Union for discharge pipe with grating and union for discharge pipe including connecting to waste pipe and flushing cistern with rectangular shaped urinal partition inlcluding froshed glass of 8mm/10mmfinish chrome size 450x 900mm complete all as specified and directed.(Make:-Jaquar, Cat No URS-WHT-13257 for urinal, Cat No JSE-CHR-110US450X for glass partition or equivalent of Hindware/ Kohler/Parryware) |
| 56 | S&F for PVC connection 15 mm dia withPTMT nuts of length 450mm at both ends screwed for iron pipe of 15 mm bore complete as in repair all as specified and directed. |
| 57 | S&F for 15 mm bore galvanized iron GI tubing medium grade with all fittings such as bends, socket, Tee, Elbow, union, Nipple, short pieces and fixed to walls, ceilings or laid in floors completeall as specified and directed. |
| 58 | S&F for 20 mm bore galvanized iron GI tubing medium grade with all fittings such as bends, socket, Tee, Elbow, union, Nipple, short pieces and fixed to walls, ceilings or laid in floors completeall as specified and directed. |
| 59 | M&L for 75mm bore PVC (SWR) floor/Nahani trap, plain with grating including jointing with solventcement complete all as specified and directed. |
| 60 | S&F for 75mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints laid in floors or trenches complete all as specified and directed. |
| 61 | S &F for 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified. |
| 62 | S&F for 110mm dia PVC (SWR) pipes type \"B\" single socketed in any length with rubber ring joints, laid in trenches or in floor complete all as specified and directed. |
| 63 | S&F for 110mm bore PVC SWR vent cowl with access door complete all as specified and directed. |
| 64 | S&F for Rotational moulded polythylene water storage tank (ISI marked of multi layer) with float valve, plastic lid cover, cylindrical vertical with closed top, hoisted and fixed in position of capacity 500 ltrs including 15mm bore ball brass valvewith union (two nos each)screwed for iron pipe and fixedcomplete all as specifed and directed. |
| 65 | Supply and laying of salt glazed stone ware drain pipe grade \"A\" 150 mm bore laid in trenches and jointed in cement mortar (1:1) complete all as specified and directed. |
| 66 | M&L for PCC (1:4:8) type D2 (using 40mm graded stone aggregate) as in concrete bed to drain pipes including packing under and haunching against the sides of salt galzed stone ware drain pipes for 150mm dia bore after they are laid and tested complete all as specified and directed. |
| 67 | M&L for cement concrete type B-0,(1:2:4) (12.5mm graded aggregate) as in coping, surface channel of drain and manhole including necessary formwork and weathering, slightly rounded or chamfered angles and throating complete all as specified and directed. |
| 68 | M&L for precast RCC (1:2:4), type B-1, (Using 20mm Graded Stone Aggregate),set in Cement Mortar (1:4) as in landing, cover slab (for manholes, septic tank/soak well) including placing in position and similar work including necessary form work complete all as specified. & directed.(Note: Reinforcement shall be measured and paid separately.) |
| 69 | M&L for 75mm thick PCC type C-2 (1:3:6), (using 40 mm graded stone aggregates) as in plinth protection, pavement etc. and finshed the surface even and smooth without using extra cement completeall as specified and directed. |
| 70 | M&L for chequered cement concrete tiles of size 30 cm x 30cmx22 mm thick set, jointed in neat cement slurry in floor and pointed in white or grey cement and no pigment of machine pressed to match the shade of tiles laid over and including 15 mm thick screed bed in cement mortar (1:6) complete all as specified and as directed. |
| 71 | M&L for PCC (1:3:6), type C-2 using 20mm graded stone aggregates as in surface channels and drain work including necessary formwork complete all as specified and directed. |
| 72 | S&F for factory made uPVC white colour Two track two panels sliding window upto 1.50 m height made of (big series) frame 67 x 50 mm sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension . (Area of window above 1.75 sqm upto 2.50 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mmthick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (whitepowder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware’s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required sizeand of approved quality, complete all as specified and directed by Engineer-in-Charge. (Cost of 4.00 mm thick ordinary sheetglassetc. shall be included in this ) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 73 | S&F for factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be included in this item ). (Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified and directed.) |
| 74 | S&F for 35mm thick factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 750 kg/cum and screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary SS screws shall be included in this item) complete all as specified and directed. |
| 75 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing rubbish off the premises complete all as specified and directed. |
| 76 | M&L for vitrifiedtiles light shade (premium quality) 10 mm thick (square/ rectangular) polished, area of each tiles exc 0.36 sqm but n. exc 0.42 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface, laid over and including 20 mm thick screed bed in cement mortar (1:4) complete all as specified and directed. |
| 77 | M&L for vitrifiedtiles light shade (premium quality) 10 mm thick (square/ rectangular) polished, area of each tiles exc 0.36 sqm but n. exc 0.42 sqmas in skirting/dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface, laid over and including 10 mm thick screed bed in cement mortar (1:4) complete all as specified and directed. |
| 78 | M&L for coloured vitrified heavy duty tiles dark shade (premium quality) of size 300mm x 300mm x 10 mm thick (square/ rectangular) polishedas in steps/stairs/raiser/vertical surface etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface, laid over and including 15 mm thick screed bed in cement mortar (1:6) complete all as specified and directed. |
| 79 | Taking down chowkhats or frames(without taking off shutters from the frames) n.exc 1.5 Sqm each complete all as specified and directed. |
| 80 | Taking down chowkhats or frames with shutter (without taking off shutter from the frame)exc 1.5 Sqmand n.exc 4 Sqm each and removing to store complete all as specified and directed. |
| 81 | Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nanital or similar pattern roof coverings complete all as specified and directed. |
| 82 | Dismantling wrought iron or mild steel work of any description not otherwise provided for all as specified. |
| 83 | S&F forfactory made uPVC white colourfixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers,plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealantover backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. ( Cost of 4.00 mm thick ordinary sheetglassetc. shall be included in this). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 84 | S&F for 100 mm dia stainless steel gratings with/without waste hole, fixedcomplete all as specified and directed. |
| 85 | M&L for 150 mm thick PCC type B-2 (1:2:4), (using 40 mm graded stone aggregates) as infloorcomplete all as specified and directed. |
| 86 | Taking down carefully copper/ aluminum point wiring (light, fan, socket or power) complete, including all fittings such as switches, ceiling roses, pendants, regulators sockets etc.) removing material from the site and making good the disturbed surfaces of walls, floor or ceiling etc. to match with existing specifications complete all as specified and directed. |
| 87 | M&L for point wiring (consealed) for one power point for one metal plug and socket set for AC or one socket for Geyser point on independent board controlled by one-MCB, 32 Amps (in and including) with 4.00 Sqmm. (nominal area) single core FRLSH,PVC insulated 1100 Volts, grade multi stranded unsheathed copper conductor unsheathed in and including non metalic rigid concealed PVCconduit of 20mm dia (Medium grade)complete with all acessories including PVC sunk box ISI marked and 4.00 Sqmm. (nominal area) single core FRLSH, PVC insulated 1100 Volts, grade multi stranded unsheathed copper conductor cable as earth wire upto common earth and connected to earth dolly including making goodthe diturbed surfaces and taking out of existing conduits and plug and socket boxes etc compete all as specified and directed.(Note:-(a) Three run of copper conductor of required size and one run of PVC conduit and accessories measured as one unit and also colour coding of wiring to be followed as red/yellow/blue for phase, black for neutral and green for earth.(b) Quoted rates shall be deemed to be inclueded for copper conductor cable, conduit & accessories , MCB and sunken box of suitable size and cutting,chasing, penning for concealed point wiring n. exc 10 cm girth in brick wall/ concrete surfaces including making good the disturbed surfaces where required and pointing in cement mortar (1:3) with necessary matching existing colour duly putting etc. complete as directed.) |
| 88 | M&L for point wiring (consealed) for one light point/fan point/exhaust fan pont/ bell point controlled by one-one way 5/6 amp switchwith 1.5 Sqmm. (nominal area) single core FRLSH,PVC insulated 1100 Volts, grade multi stranded unsheathed copper conductor unsheathed in and including non metalic rigid concealed PVCconduit of 20mm dia (Medium grade)complete with all acessories including PVC sunk box ISI marked for mounting of switches, sockets, fan regulator etc with 3 mm thick plastic laminated sheet as top cover, and 1.5 Sqmm. (nominal area) single core FRLSH, PVC insulated 1100 Volts, grade multi stranded unsheathed copper conductor cable as earth wire upto common earth and connected to earth dolly including making goodthe diturbed surfaces compete all as specified and directed.(Note:-(a) Three run of copper conductor of required size and one run of PVC conduit and accessories measured as one unit and also colour coding of wiring to be followed as red/yellow/blue for phase, black for neutral and green for earth.(b) Quoted rates shall be deemed to be inclueded for copper conductor cable, conduit & accessories, cover plate and sunken box of suitable size and cutting,chasing, penning for concealed point wiring n. exc 10 cm girth in brick wall/ concrete surfaces including making good the disturbed surfaces where required and pointing in cement mortar (1:3) with necessary matching existing colour duly putting etc. complete as directed.) |
| 89 | Description all as per srl item No. 88 above but for socket outlet 5/6 Amps on same board complete all as specified and directed. |
| 90 | Description all as per srl item No. 88 above but for one 5 pin, socket outlet, 5/6 Amps on independent board complete all as specified and directed. |
| 91 | Description all as per Serial item No 88above but for one 3 pin, 15/16 Amp socket outlet independent with2.5 sqmm PVC insulated FRLSH multistraind copper cable with 2.5 sqmm single core multistraind FRLSH copper cable as earthling lead complete all as specified and directed. |
| 92 | S&F for switch modular typeone way 6 Amps 230 volts, with one module, complete all as specified and directed. |
| 93 | S&F for switch modular typeone way 16 Amps 240 volts, with one module matching with existing plate complete all as specified and directed. |
| 94 | S&F for shuttered socket outlet modular type6 Amps , 2/3 pin combined, 240 volts, with two module matching with existing plate complete all as specified and directed. |
| 95 | S&F for shuttered socket outletmodular type6/16 Amps , 2/3 pin combined, 240 volts, with two module matching with existing plate complete all as specified and directed. |
| 96 | S &F of modular type bell push button, flush type, 5 Amp complete as in repair all as specified and directed. |
| 97 | S&F for modular fan regulator stepped type, 120 watts, two module matching with existing plate complete as in repair all as specified and directed. |
| 98 | S&F for lamp holder, insulated body, with back plate suitable for batten/ angle fittings including 1x 9 watt LED white glass lamp, 230 volt base22 complete as in repair all as specified and directed |
| 99 | S&F for ceiling rose 3 phase, PVC/polycarbonate isolated body surface bakelite2 to 3 terminals fixed to wall/ceiling complete all as specified and directed. |
| 100 | M&L forsub main wiring (Concealed) complete with 02 run of 6 sqmm, single core, copper conductor cable 1100 volts grade, FRLSH type, PVC insulated, unsheathed, flexible, multi strandedduly colour coded cable drawn through and including concealed PVC conduit of size 32mm dia or above (medium grade) as required at site and accessories such as tee, corners,overlaping connector etc of suitable size fixed on surface of walls/roofs/ceiling and including 01 run of 6 sqmm single core, copper conductor cable 1100 volts grade, FRLSH type, PVC insulated, unsheathed, flexible, multi stranded of green colour as earth continuity conductor connected to common earth dolly including removing old unserviceable sub main wiring items of any types complete all as specified and directed.(Note : -(a) 02 run of 6 sqmm single core copper conductor cable and 01 run of 6 sqmm single core copper conductor and 01 run of PVC conduit and accessories shall be measured as one unit and also colour coding of wiring to be followed as red/yellow/blue for phase, black for neutral and green for earth).(b)Quoted rates shall be deemed to be inclueded for copper conductor cable, conduit & accessories and cutting,chasing, penning for concealed submain wiring n. exc 10 cm girth in brick wall/ concrete surfaces including making good the disturbed surfaces where required and pointing in cement mortar (1:3) with necessary matching existing colour duly putting etc. complete as directed.) |
| 101 | M&L for sheet metal enclosure MCB distribution board, double door (metal) single pole and neutral with IP-30 and IK 09 protection single phase 240 volts 8 way, including suitable size copper bus bar of 100 amp and neutral link fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete as in repair all as specified and directed. (Note:-MCBs will be measured separately.) |
| 102 | M&L for MCB, SPN, 240 volts, 40-63 amps with rupturing capacity 10 KA, \"C\" curve, including providing thimble for out going cables complete all as specified and directed. |
| 103 | M&L for MCB, SP, 240 volts, 5-32 amps with rupturing capacity 10 KA, \"C\" curve, including providing thimble for out going cables complete all as specified and directed. |
| 104 | S&F for PVC exhaust fan of 250mm sweep, 220-240 Volt, 50 Hz with thermal overload protection (Approve by GE)and louvers shutter complete as in repair all as specified and directed. (Make : Crompton Brisk Air/ Bajaj Maxima/ Havells Thrill Air/ Atomberg Efficio)(Note:- (i) Purchase voucher having GST No submitted by the contractor before claiming any paymet duly verified and defeced by the Engr-in-Charge(ii) Two years warranty shall be given by the appoved company of exhaust fan and contractor also) |
| 105 | M&L for LED Tube light fitting, complete with 1x 20 watts, 220V, AC CCT 6500K, smart extruded with driver, holderandincluding LED tube light connection Aluminium LED pattern (4ft) with higher effect complete. Microwave sensor to save more energy. Reduce the light intensity by 70% during non occupancy with three code flexible copper conductor cable suitable size from ceiling rose and necessary fixing arrangement at any height complete as in repair all as specified and directed. (Note: Material required for safety harness, ladder and T&P etc will be provided by the contractor without any extra cost).(Make: Havells, Cat No. LUMILINEPLUSNEOBS20WLED865SPCSSIND or Crompton, Cat No. CCS-103-20-65-SL-DP-NWH or equivalent in Philips) |
| 106 | M&L for LED Tube light fitting, complete with 1x 10 watts, 220V, AC CCT 6500K, smart extruded with driver, holderandincluding LED tube light connection Aluminium LED pattern (4ft) with higher effect complete. Microwave sensor to save more energy. Reduce the light intensity by 70% during non occupancy with three code flexible copper conductor cable suitable size from ceiling rose and necessary fixing arrangement at any height complete as in repair all as specified and directed. (Note: Material required for safety harness, ladder and T&P etc will be provided by the contractor without any extra cost).(Make: Havells, Cat No. LUMILINEPLUSNEOBS10WLED865SPCSSIND or Crompton, Cat No. CCS-103-10-65-SL-DP-NWH or equivalent in Philips) |
| 107 | S&F for High efficacy 2\"x2\" recess LED flat panel light fittings 36W LED 6000K edge-lit luminaire with in and including LED lamp suitable for armstrong/grid ceiling complete for low ceiling applications complete with all accessories pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete as in repair all as specified and directed. (Make: Havells, Cat No. VENUSTREND2X2PLR36WLED865SWH or Crompton, Cat No. TCR-145-36-65-SL-NWH or equivalent in Philips) |
| 108 | S & F for modular white cover palte with frame, 1 module complete all as specified |
| 109 | S & F for modular white cover palte with frame, 2 module complete all as specified |
| 110 | S & F for modular white cover palte with frame, 3 module complete all as specified |
| 111 | S & F for modular white cover palte with frame, 6 module complete all as specified |
| 112 | S & F for modular white cover palte with frame, 8 module complete all as specified |
| 113 | Material and labour for Earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6.3 mm thick buried directly in ground( earth pit not less than 2.25 mtrs deep below normal ground level )with the top edges of plate not less than 1.5 mtrs below normal ground level connected to GI wire 4mmby means of GInuts, bolts check nuts and washers earth lead protected by 15mm dia GI pipe light grade and connected to main distribution board/earthing test pointall as shown in electrical plate No 3 of SSR part 1 and all as specified including taking down old unserviceable earthing and testing of earthing on completion. Notes:-The unit rate also including for excavation, earth work in any type of strata, plain cement concrete 1:3:6 mix, Type C1 pit, 40mm thick RCC 1:2:4 mix , type B1 cover reinforced with 8mm dia TMT bars @150mm C/C both ways ,GI funnel with GIwatering pipe 20mm dia medium grade, wire mesh, protection pipe 15mm dia GI pipe light grade for earth lead upto 7.50m long complete all specified and directed. |
| 114 | S & F for epoxy powder coated sheet metal enclosure eith socket plug top and MCB, Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 32 Amps, 240 volts, C series current carrying capacity 10 KA, incl necessary connection complete as in repair all as specified and directed. |
| 115 | S & F for ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated including fixing clamp and all accessoriescomplete all as specified and directed. |
