|
| 1 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm DAR NO-15.23.1 |
| 2 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete.(dar-11.38) ( size of tile 300x300mm ) |
| 3 | Providing and fixing 1st quality ceramic, glazed wall tiles conforming to IS 15622 (thickness to be specified by the manufacturer) of approved make in all colours, shades except burgundy, bottle green black of any size as approved by Engineer-in-charge, in skirting, risers of steps and dados, over 12 mm thck bed of cmeent mortar 1:3 ( 1 cement 3 coarse sand) and jointing with grey cmeent slurry @ 3.3 kg per sqm, including pointign in white cement mixed with pigment of matching shade complete.DAR NO-8.31 |
| 4 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: of size 580x440 mm 17.1.1 |
| 5 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer DAR No- 17.7.A |
| 6 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore DAR NO-18.50.1 |
| 7 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bore DAR NO-18.53.1 |
| 8 | Providing and fixing uplasticised PVC connection pipe with brass unions :45 cm length 20 mm nominal bore DAR No-18.21.2.2 |
| 9 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality ) complete with 6 mm thick hard board ground fixed to wooden cleats with c.p brass screws and washers complete(dar-17.31) |
| 10 | Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge. all kinds of soil . DAR NO-(2.6.1) |
| 11 | Providing and layeing in position cement concrete of specified grade excluding the cost of centering and shuttering All work up to plinth level:1:2:4 (1 cement :2 coasre sand ( Zone-III) :4 graded stone aggregate 20 mm nominal size (4.1.3) |
| 12 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required::In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. (10.25.2) |
| 13 | Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.1.00 mm thick with zinc coating not less than 275 gm/m² DAR NO-12.1.1 |
| 14 | supplying and fixing c.i cover without frama for manholes:456x610 mm rectangular c.i (light duty ) the weight of the cover to be not less than 23 kg (19.18.1) Please Enable Macros to View BoQ information |
